How much money are you wasting by using worm gear motors? · PDF fileShaft-mounted right angle...
Transcript of How much money are you wasting by using worm gear motors? · PDF fileShaft-mounted right angle...
usa.siemens.com/SIMOGEAR
Shaft-mounted right angle gear motors are the new normal for conveyors. When faced with the decision of whether to use a bevel or worm gear motor, you may be tempted to choose the latter, because it is seemingly less expensive and gives you the output speed and torque that you require. What you may not have realized is that worm gears are the least efficient type of right angle gearing, and the associated long-term energy costs far outweigh the initial investment. The example below illustrates why a worm gear motor may not be the best choice.
This conveyor application requires 1.4 HP at the load with an output speed of 53 rpm.
Helical Worm Helical Bevel
Initial cost for end user $890 $930
Gearbox efficiency 80% 96%
Required output power 1.4 HP 1.4 HP
Required motor power 2 HP 1.5 HP
Energy cost per year $366/year $305/year
Now let’s extrapolate these results to resemble a more typical scenario in an industrial setting. The figure below shows the total cost of 200 units over 5 years. By using helical bevel gearing instead of helical worm gearing, you would save over $52,000 with a return on investment of less than 1 year.
Assumptions: Both gear motors use the same NEMA Energy Efficient motor, energy cost is $0.07 per kWh, run-time of 4,000 hrs/yr. Maintenance costs are not included.
usa.siemens.com/SIMOGEAR
How much money are you wasting by using worm gear motors?
Disadvantages of worm gearing• Least efficient type of right-angle gearing• In high run-time applications, the energy costs far
outweigh the initial investment• Energy is lost in the form of heat due to sliding friction
between the worm and worm gear• Efficiency decreases as gear ratio increases, or as
output speed decreases• Efficiency decreases as motor input speed decreases• Bronze worm gears are designed to wear and must be
replaced periodically
www.usa.siemens.com/SIMOGEAR
Subject to change without prior notice Order No.: MDFL-00001-0713 Printed in USA © 2013 Siemens Industry, Inc.
Siemens Industry, Inc. 3333 Old Milton Parkway Alpharetta, GA 30005 1-800-241-4453
The information provided in this flyer contains merely general descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract.
All product designations may be trademarks or product names of Siemens AG or supplier companies whose use by third parties for their own purposes could violate the rights of the owners.
SIMOGEAR helical bevel gear motors• Mounting options: Foot, flange, and torque arm• Inch or metric shafts in common dimensions• Shaft types: Solid, hollow, and SIMOLOC• Gear teeth hardened and ground for infinite life• Synthetic oil standard for longer maintenance intervals• Aluminum housings are lightweight and do not require paint• Inverter-duty NEMA Premium® and NEMA Energy Efficient
motors (230/460VAC, 60Hz)• Conduit box with NPT-tapped holes• Standard 9-pin terminal block in 3x3 configuration
Helical bevel gear motors 2-stage (B Series)
Helical bevel gear motors 3-stage (K Series)
Efficiency Up to 96% Up to 94%
Output torque (lb-in) 442 to 3,982 1,947 to 14,160
Ratio 3.47 to 59.28 5.17 to 244.25
Motor power (HP) 1/3 to 10 1/3 to 20
Easy installation• SIMOLOC keyless tapered shaft locking system allows for
easier installation on hollow shaft applications• An integrated mounting flange is incorporated into the
gearbox housing, however other common flanges are also available
E-readable• RFID nameplates allow for quick identification, while Smart
Numbers make ordering of exact duplicates effortless
Field modifiable• MODULOG modular concept uses various mounting shafts to
add options such as brakes, encoders, and external fans that can be field-retrofitted after installation
The power of 2%:
Our SIMOGEAR 2-stage helical bevel unit gives you higher ratios in the first gear stage than traditional designs. All told, the unit averages 2% higher efficiency than 3-stage units. For any continuous duty application, that translates to substantial energy savings over the long term.
Gear type has a drastic effect on efficiency
NEMA Premium® is a certification mark of the National Electrical Manufacturers Association. (US DOE CC# 032A)