How Electric Cars Workby Marshall Brain

Image Gallery: Electric Cars The Subaru R1e electric car can be charged overnight on household current. It has a range of 50 miles and a top speed of 62 miles per hour. See more electric car pictures.

STAN HONDA/AFP/Getty Images

Electric cars are something that show up in the news all the time. There are several reasons for the continuing interest in these vehicles:

Electric cars create less pollution than gasoline-powered cars, so they are an environmentally friendly alternative to gasoline-powered vehicles (especially in cities).

Any news story about hybrid cars usually talks about electric cars as well. Vehicles powered by fuel cells are electric cars, and fuel cells are getting a lot of

attention right now in the news.

An electric car is a car powered by an electric motor rather than a gasoline engine.

From the outside, you would probably have no idea that a car is electric. In most cases, electric cars are created by converting a gasoline-powered car, and in that case it is impossible to tell. When you drive an electric car, often the only thing that clues you in to its true nature is the fact that it is nearly silent.

Under the hood, there are a lot of differences between gasoline and electric cars:

The gasoline engine is replaced by an electric motor. The electric motor gets its power from a controller.

The controller gets its power from an array of rechargeable batteries.

A gasoline engine, with its fuel lines, exhaust pipes, coolant hoses and intake manifold, tends to look like a plumbing project. An electric car is definitely a wiring project.

In order to get a feeling for how electric cars work in general, let's start by looking at a typical electric car to see how it comes together.

An Electric Car ExampleThe electric car that we will use for this discussion is shown here.

A typical electric car, this one has some particularly snazzy decals. This vehicle is owned by Jon Mauney.

This electric vehicle began its life as a normal, gasoline-powered 1994 Geo Prism. Here are the modifications that turned it into an electric car:

The gasoline engine, along with the muffler, catalytic converter, tailpipe and gas tank, were all removed.

The clutch assembly was removed. The existing manual transmission was left in place, and it was pinned in second gear.

A new AC electric motor was bolted to the transmission with an adapter plate. An electric controller was added to control the AC motor.

The 50-kW controller takes in 300 volts DC and produces 240 volts AC, three-phase. The box that says "U.S. Electricar" is the controller.

A battery tray was installed in the floor of the car. Fifty 12-volt lead-acid batteries were placed in the battery tray (two sets of 25 to create

300 volts DC). Electric motors were added to power things that used to get their power from the engine:

the water pump, power steering pump, air conditioner. A vacuum pump was added for the power brakes (which used engine vacuum when the

car had an engine).

The vacuum pump is left of center.

The shifter for the manual transmission was replaced with a switch, disguised as an automatic transmission shifter, to control forward and reverse.

An automatic transmission shifter is used to select forward and reverse. It contains a small switch, which sends a signal to the controller.

A small electric water heater was added to provide heat.

The water heater

A charger was added so that the batteries could be recharged. This particular car actually has two charging systems -- one from a normal 120-volt or 240-volt wall outlet, and the other from a magna-charge inductive charging paddle.

The 120/240-volt charging system

The Magna-Charge inductive paddle charging system

The gas gauge was replaced with a volt meter.

The "gas gauge" in an electric car is either a simple volt meter or a more sophisticated computer that tracks the flow of amps to and from the battery pack.

Everything else about the car is stock. When you get in to drive the car, you put the key in the ignition and turn it to the "on" position to turn the car on. You shift into "Drive" with the shifter, push on the accelerator pedal and go. It performs like a normal gasoline car. Here are some interesting statistics:

The range of this car is about 50 miles (80 km). The 0-to-60 mph time is about 15 seconds. It takes about 12 kilowatt-hours of electricity to charge the car after a 50-mile trip. The batteries weigh about 1,100 pounds (500 kg). The batteries last three to four years.

To compare the cost per mile of gasoline cars to this electric car, here's an example. Electricity in North Carolina is about 8 cents per kilowatt-hour right now (4 cents if you use time-of-use billing and recharge at night). That means that for a full recharge, it costs $1 (or 50 cents with time-of-use billing). The cost per mile is therefore 2 cents per mile, or 1 cent with time-of-use. If gasoline costs $1.20 per gallon and a car gets 30 miles to the gallon, then the cost per mile is 4 cents per mile for gasoline.

Clearly, the "fuel" for electric vehicles costs a lot less per mile than it does for gasoline vehicles. And for many, the 50-mile range is not a limitation -- the average person living in a city or suburb seldom drives more than 30 or 40 miles per day.

To be completely fair, however, we should also include the cost of battery replacement. Batteries are the weak link in electric cars at the moment. Battery replacement for this car runs about $2,000. The batteries will last 20,000 miles or so, for about 10 cents per mile. You can see why

there is so much excitement around fuel cells right now -- fuel cells solve the battery problem (more details on fuel cells later in the article).

Inside an Electric CarThe heart of an electric car is the combination of:

The electric motor The motor's controller The batteries

A simple DC controller connected to the batteries and the DC motor. If the driver floors the accelerator pedal, the controller delivers the full 96 volts from the batteries to the motor. If the driver take his/her foot off the accelerator, the controller delivers zero volts to the motor. For any setting in between, the controller "chops" the 96 volts thousands of times per second to create an average voltage somewhere between 0 and 96 volts.

The controller takes power from the batteries and delivers it to the motor. The accelerator pedal hooks to a pair of potentiometers (variable resistors), and these potentiometers provide the signal that tells the controller how much power it is supposed to deliver. The controller can deliver zero power (when the car is stopped), full power (when the driver floors the accelerator pedal), or any power level in between.

The controller normally dominates the scene when you open the hood, as you can see here:

The 300-volt, 50-kilowatt controller for this electric car is the box marked "U.S. Electricar."

In this car, the controller takes in 300 volts DC from the battery pack. It converts it into a maximum of 240 volts AC, three-phase, to send to the motor. It does this using very large transistors that rapidly turn the batteries' voltage on and off to create a sine wave.

When you push on the gas pedal, a cable from the pedal connects to these two potentiometers:

The potentiometers hook to the gas pedal and send a signal to the controller.

The signal from the potentiometers tells the controller how much power to deliver to the electric car's motor. There are two potentiometers for safety's sake. The controller reads both potentiometers and makes sure that their signals are equal. If they are not, then the controller does not operate. This arrangement guards against a situation where a potentiometer fails in the full-on position.

Heavy cables (on the left) connect the battery pack to the controller. In the middle is a very large on/off switch. The bundle of small wires on the right carries signals from thermometers located between the batteries, as well as power for fans that keep the batteries cool and ventilated.

The heavy wires entering and leaving the controller

The controller's job in a DC electric car is easy to understand. Let's assume that the battery pack contains 12 12-volt batteries, wired in series to create 144 volts. The controller takes in 144 volts DC, and delivers it to the motor in a controlled way.

The very simplest DC controller would be a big on/off switch wired to the accelerator pedal. When you push the pedal, it would turn the switch on, and when you take your foot off the pedal, it would turn it off. As the driver, you would have to push and release the accelerator to pulse the motor on and off to maintain a given speed.

Obviously, that sort of on/off approach would work but it would be a pain to drive, so the controller does the pulsing for you. The controller reads the setting of the accelerator pedal from the potentiometers and regulates the power accordingly. Let's say that you have the accelerator pushed halfway down. The controller reads that setting from the potentiometer and rapidly switches the power to the motor on and off so that it is on half the time and off half the time. If you have the accelerator pedal 25 percent of the way down, the controller pulses the power so it is on 25 percent of the time and off 75 percent of the time.

Most controllers pulse the power more than 15,000 times per second, in order to keep the pulsation outside the range of human hearing. The pulsed current causes the motor housing to vibrate at that frequency, so by pulsing at more than 15,000 cycles per second, the controller and motor are silent to human ears.

An AC controller hooks to an AC motor. Using six sets of power transistors, the controller takes in 300 volts DC and produces 240 volts AC, 3-phase. See How the Power Grid Works for a discussion of 3-phase power. The controller additionally provides a charging system for the batteries, and a DC-to-DC converter to recharge the 12-volt accessory battery.

In an AC controller, the job is a little more complicated, but it is the same idea. The controller creates three pseudo-sine waves. It does this by taking the DC voltage from the batteries and

pulsing it on and off. In an AC controller, there is the additional need to reverse the polarity of the voltage 60 times a second. Therefore, you actually need six sets of transistors in an AC controller, while you need only one set in a DC controller. In the AC controller, for each phase you need one set of transistors to pulse the voltage and another set to reverse the polarity. You replicate that three times for the three phases -- six total sets of transistors.

Most DC controllers used in electric cars come from the electric forklift industry. The Hughes AC controller seen in the photo above is the same sort of AC controller used in the GM/Saturn EV-1 electric vehicle. It can deliver a maximum of 50,000 watts to the motor.

Electric-car Motors and BatteriesElectric cars can use AC or DC motors:

If the motor is a DC motor, then it may run on anything from 96 to 192 volts. Many of the DC motors used in electric cars come from the electric forklift industry.

If it is an AC motor, then it probably is a three-phase AC motor running at 240 volts AC with a 300 volt battery pack.

DC installations tend to be simpler and less expensive. A typical motor will be in the 20,000-watt to 30,000-watt range. A typical controller will be in the 40,000-watt to 60,000-watt range (for example, a 96-volt controller will deliver a maximum of 400 or 600 amps). DC motors have the nice feature that you can overdrive them (up to a factor of 10-to-1) for short periods of time. That is, a 20,000-watt motor will accept 100,000 watts for a short period of time and deliver 5 times its rated horsepower. This is great for short bursts of acceleration. The only limitation is heat build-up in the motor. Too much overdriving and the motor heats up to the point where it self-destructs.

AC installations allow the use of almost any industrial three-phase AC motor, and that can make finding a motor with a specific size, shape or power rating easier. AC motors and controllers often have a regen feature. During braking, the motor turns into a generator and delivers power back to the batteries.

Right now, the weak link in any electric car is the batteries. There are at least six significant problems with current lead-acid battery technology:

They are heavy (a typical lead-acid battery pack weighs 1,000 pounds or more). They are bulky (the car we are examining here has 50 lead-acid batteries, each measuring

roughly 6" x 8" by 6"). They have a limited capacity (a typical lead-acid battery pack might hold 12 to 15

kilowatt-hours of electricity, giving a car a range of only 50 miles or so). They are slow to charge (typical recharge times for a lead-acid pack range between four

to 10 hours for full charge, depending on the battery technology and the charger). They have a short life (three to four years, perhaps 200 full charge/discharge cycles). They are expensive (perhaps $2,000 for the battery pack shown in the sample car).

In the next section we'll look at more problems with battery technology.

The EV Challenge

The EV Challenge (www.ev-challenge.org) is an innovative educational program for middle and high school students that centers around building electric-powered cars:

Middle school students build and compete model solar-powered cars. High school students convert full-sized gasoline-powered vehicles into electric vehicles. It's a

complete conversion project, as described in the previous section of this article.

Students learn about electric technology throughout the year and then come together for a two-day finale. In addition to building the electric vehicle, high school students compete in autocross (speed and agility) and range events, vehicle design, oral presentations, troubleshooting, Web site design, and community involvement.

The EV Challenge gets a majority of its funding from corporate sponsors and government organizations, including Advanced Energy Corporation, CP&L/Progress Energy, Duke Power, Dominion Virginia Power, the NC Energy Office, the NC Department of Environment and Natural Resources, and the EPA.

Jon Mauney (whose car is featured at the beginning of this article) is on the steering committee for EV Challenge. According to Jon, CP&L started the EV Challenge program in North Carolina. The program then spread to South Carolina, Florida, Virginia, West Virginia, and Georgia, and is now spreading nationwide. Thousands of students have participated in the EV Challenge.

If you or your school would like more information on the EV Challenge program, please see www.ev-challenge.org.

Energy smart inventions

All over the world, scientists are finding new ways to save energy – and make energy. In a few years, you might even be using some of these new energy-smart inventions in your home or school.

Electric car

Electric vehicles have been around for a very long time. In the early 1900s, there were more electric vehicles than there were gasoline-powered cars. The vehicle pictured is a Rauch and Lang Electric Sedan, built around 1922.

Gasoline back then was very expensive. It also was hard to start a gasoline engine; you had to turn and turn and turn a crank in front of the car to get it to start. They did not have a key to start the car like we do today. Gasoline vehicles were also noisy and put out lots of smoke. The cars either had no mufflers, or the mufflers didn't do a good job. So, electric vehicles were a BIG hit!

How Do Electric Vehicles Work?Electric vehicles (like the Ford Ranger Electric Vehicle above on the left) don't burn gasoline in an engine. They use electricity stored on the car in batteries. Sometimes, 12 or 24 batteries, or more, are needed to power the car. Just like a remote-controlled, model electric

car, EVs have an electric motor that turns the wheels and a battery to run that motor.

One of the first modern EVs was the General Motors Impact. GM changed its name and started selling the GM "EV1" in 1997. This sleek looking car even set a World Record of more than 180 miles per hour!

The EV1 is very aerodynamic. This means that air slides around the body of the car very easily. The less air resistance or drag, the less energy is needed to power the car at freeway speeds.

The EV1 is as aerodynamic as some jet fighter aircraft!

Charging an Impact EV To charge an EV's batteries, the car is usually plugged in at night. In

the picture to the left, an Impact test vehicle is plugged into a special charging unit attached to a house. The Impact is not yet available for sale. Some EVs can plug right into a regular electrical wall outlet. Others need a larger outlet, like the kind that a stove or electric clothes dryer plug into.

Electricity, the same energy that lights your lamps and runs your TV, is stored in batteries on an EV.

The batteries can be lead acid batteries, like the batteries you find in our flashlight or in regular gasoline cars. Or they can be ni-cad (nickel-cadmium) like the kind that run portable video recorders or a portable video game player -- only much larger.

Better batteries that hold more energy and last longer are being developed. In 2001, by the time today's fifth graders are ready to drive, electric vehicles should be able to go 150 to 200 miles before recharging.

What About Solar-Powered Cars?Unfortunately, electric cars will probably not be solar-powered. Solar cells, also called photovoltaic cells, produce too little power. They are not practical to power a full-sized electric car.

Some colleges, however, race solar-powered cars. The picture on the right is the solar car from California Polytechnic University in Pomona, California -- CalPoly Pomona for short.

The back of the car is covered with solar cells, but all those solar cells only produce enough power to run an electric hair dryer...about 1,500 watts.

That's not enough energy to run a heavy vehicle. The CalPoly Pomona solar car is also very light, less than 400 pounds. It's not strong enough to be in traffic and protect a driver in an accident with another car or truck.