Hot Water Heater Replacement
2
Information on Hot Water Heater Replacement Hot water heater replacement is not a very difficult job to perform. When you found out that one day your water heater doesn’t function as efficient and as effective as they should be then it’s time to replace them with new ones. You should know that water heaters are just like other appliances that are composed of small and large parts that can either be repaired or replaced. Like all the electrical and mechanical things, they can and they will break down eventually. Yes, you can still repair the troubled water heater or you may just replace some parts but look if the cost is just somewhat the same as buying a new one then it’s better to upgrade and replace it with a new one. Overall you all need a water heater that works as efficient as you want, so don’t hesitate to upgrade when you know it’s best for you. Again when you want a hot water heater replacement, it’s always sensible to get help from a local service provider that is expert in this kind of work. Generally, when you buy an upgraded water heater you know that it will last long when adequate and proper preventive maintenance is regularly performed. If a hot water heater replacement is to be performed by an owner, then the following information will help you in the process. Remove the old and broken water heater Switch off the water heater’s power and at the same time turn off the breaker as well. Check all connections that it is properly switch off. Disconnect all the wirings associated with the water heater. Make sure that you leave a visible mark for you to know which wires should be put when a new water heater is installed. Switch off the water supply from the water heater at the same time turn on all the hot water spigots. Connect a hose at the drain valve and allow the tank to fully drain completely. Disconnect all the cold and hot water inlet and outlets from the unit. Ask for help when removing the old water heater as this thing is heavy. Installing the new and upgraded water heater Place the new water heater in its proper position. Reconnect the cold and hot water inlet and outlets to the new water heater. Turn on the water heater supply. Remember to let the spigot open so that air will not be trapped inside the hot water tank as the tank is being filled. Let the tank to be filled with water until water flows from each of the spigots and turn it off after a minute. Refer to the instructor’s manual and reconnect the wiring to the heater accordingly. Turn on the breaker and let the water heat up.
-
Upload
michael-parrish -
Category
Technology
-
view
89 -
download
0
Transcript of Hot Water Heater Replacement
Information on Hot Water Heater Replacement Hot water heater replacement is not a very difficult job to perform. When you found out that one day your water heater doesn’t function as efficient and as effective as they should be then it’s time to replace them with new ones. You should know that water heaters are just like other appliances that are composed of small and large parts that can either be repaired or replaced. Like all the electrical and mechanical things, they can and they will break down eventually. Yes, you can still repair the troubled water heater or you may just replace some parts but look if the cost is just somewhat the same as buying a new one then it’s better to upgrade and replace it with a new one. Overall you all need a water heater that works as efficient as you want, so don’t hesitate to upgrade when you know it’s best for you. Again when you want a hot water heater replacement, it’s always sensible to get help from a local service provider that is expert in this kind of work. Generally, when you buy an upgraded water heater you know that it will last long when adequate and proper preventive maintenance is regularly performed. If a hot water heater replacement is to be performed by an owner, then the following information will help you in the process. Remove the old and broken water heater
Switch off the water heater’s power and at the same time turn off the breaker as well. Check all connections that it is properly switch off.
Disconnect all the wirings associated with the water heater. Make sure that you leave a visible mark for you to know which wires should be put when a new water heater is installed.
Switch off the water supply from the water heater at the same time turn on all the hot water spigots. Connect a hose at the drain valve and allow the tank to fully drain completely.
Disconnect all the cold and hot water inlet and outlets from the unit.
Ask for help when removing the old water heater as this thing is heavy. Installing the new and upgraded water heater
Place the new water heater in its proper position.
Reconnect the cold and hot water inlet and outlets to the new water heater.
Turn on the water heater supply. Remember to let the spigot open so that air will not be trapped inside the hot water tank as the tank is being filled. Let the tank to be filled with water until water flows from each of the spigots and turn it off after a minute.
Refer to the instructor’s manual and reconnect the wiring to the heater accordingly. Turn on the breaker and let the water heat up.
Relief System
The provision of temperature and pressure relief valve and its relief line is the very important part of installing a water heater. The relief system is specially designed to release excess heat and pressure automatically.
Be sure that all plumbing are properly connected. Energy Hookup
Connect the gas or the electric lines to the heater. There are several potential dangers when doing hot water heater replacement. Be sure to check all the procedures and materials and always ask for help. Generally, hot water heater replacement is usually done by professionals. Just make sure that you all have the necessary tools before starting your hot water heater replacement. Never be afraid of consulting a plumber or an electrician.
