Holiday Ornaments Pillow - Viking Sewing Gallery½ yard fabric A (linen/cotton blend fabric for...

of 16 ©2014 KSIN Luxembourg ll, S.ar.I. VIKING, INSPIRA and DESIGNER DIAMOND ROYALE are trademarks of KSIN Luxembourg ll, S.ar.I. HUSQVARNA is a trademark of Husqvarna AB. All trademarks used under license by VSM Group AB.

DESIGNER DIAMOND Royale™ Advanced Workshop Holiday Ornaments Pillow

By Linda Holmes

Expand your sewing and embroidery machine skills in this advanced workshop while you create an elegant holiday pillow using decorative stitches to create ornaments and snowflakes. Suspend the ornaments on the pillow using yarns, ribbons, bows and buttons. Insert an invisible zipper for the closure on the back.

Sewing Supplies:

HUSQVARNA VIKING® Sensor Q Foot 413192045 HUSQVARNA VIKING® Straight stitch needle plate 412964203 HUSQVARNA VIKING® Ribbon Foot Set 920239096 HUSQVARNA VIKING® Button Foot with Placement Tool 412934545 HUSQVARNA VIKING® Clear Invisible Zipper Foot 413286545 HUSQVARNA VIKING® 3-Hole Yarn Foot 413187045 HUSQVARNA VIKING® Clear Seam Guide Foot 413034845 HUSQVARNA VIKING® Clear Open Toe Foot 413031945 HUSQVARNA VIKING® 120mm x 120mm Splendid Square Hoop 412968201 HUSQVARNA VIKING® USB embroidery stick 413095706 HUSQVARNA VIKING® Pictogram Pen 412083845 INSPIRA® Duck Bill Applique scissors 620102796


INSPIRA® Sheer & Stable stabilizer 12” x 5 yards 620133396 INSPIRA® Whisper Web Mesh stabilizer 12” x 12 yards 620111196 INSPIRA® Tear-A-Way stabilizer 12” x 10 yards 620120001 INSPIRA® Water Works soluble film 12” x 10 yards 620114096 ½ yard fabric A (linen/cotton blend fabric for pillow) ¼ yard fabric B (sparkle chiffon slightly darker than the linen/cotton fabric) 20” invisible zipper to match fabric A ⅓ yard each of 6 various ribbons ¼” to 3/8” wide 3 skeins yarn – size 4 – in 3 different colors Various buttons approximately 1” diameter 4 Robison-Anton 40wt. rayon embroidery threads to coordinate with fabric 1 Bobbins wound with embroidery bobbin thread Sewing thread to match fabric 1 Bobbin wound with matching thread Screwdriver 412381501 Stylus 413171702 Rotary cutter

Rotary mat

6” x 24” rotary cutting ruler

Erasable marking pen

Straight pins

Pressing surface

Iron

Glue stick (optional)

Cut: Whisper Web Mesh stabilizer:

(5) 10”L x 12”W Tear-A-Way stabilizer:

(5) 6”L x 6”W Water Works soluble film:

(3) 6”L x 6”W From Fabric A:

15”L x 18” W (2) 9”L x 18”W


From fabric B: (2) 6” squares

From various ribbons: (6) 12” pieces

From various yarns: (6) 15” pieces

Prepare: Prepare the pillow front fabric by drawing a vertical line down the center. Mark a short horizontal line on the vertical line, 6” up from the bottom. Draw vertical lines on each side of the center line 3” away. Draw short horizontal lines on each of these lines, 5” from the top. Draw vertical lines 5½” on each side of the center line. Draw short horizontal lines on each of these lines, 4½” from the bottom. These will be the center markings for each ornament. Turn on the DESIGNER DIAMOND Royale™. Calibrate the embroidery unit. Attach the Sensor Q Foot and the Straight Stitch Needle Plate. All designs will be created in the 120mm x 120mm Splendid Square hoop. Once that hoop is selected, that hoop size will remain selected.

Create:

Ornament 1 1. Touch My Hoops and select 120x120. 2. Touch the Designs Menu. Scroll down and choose design ROY_108.vp3. 3. Touch Scale, then touch the up arrow on the control wheel to enlarge the design

to its max size. 4. Touch Save to My Designs. Touch USB peripheral devices. Touch and hold

the icon for your USB embroidery stick. 5. Touch Rename File or Folder, then touch and hold Delete to clear the name


field. Name the design Ornament 1.vp3. Touch OK to accept the new name and touch OK to save the design.

6. Touch and hold Delete to clear the embroidery field.

Ornament 2 1. Touch the Stitch Menu. Select the C Menu. 2. Select stitch C1:5. Set the stitch length to 14.0 and leave the width at 7.0. 3. Touch ALT and set the density to 0.2. 4. Select C1:2. Set the stitch length to 20.0 and leave the width at 7.0 5. Touch ALT and set the density to 0.2. 6. Touch Mirror End to End. 7. Touch OK to exit Program mode. 8. Touch Thread Color Edit. Select color 1:1, and then touch Quick Color

Change. Select the brightest yellow in the second row, last column. Touch OK to close the pop-up, and then touch OK to close Thread Color Edit.

9. Touch Design Shaping. 10. Select Circle Clockwise. 11. Set the Number of Objects to 6. Touch OK to close the pop-up. 12. Touch Select Side Positioning, and choose Rotated 90° CCW. Touch OK to

close the pop-up. 13. Scale to 35.5. 14. Touch OK to close Design Shaping. 15. Touch the Stitch Menu. Select stitch C1:2. Set the stitch length to 10.0 and the

width to 6.0. 16. Touch ALT and set the density to 0.2. 17. Touch Duplicate, then Mirror End to End. 18. Change the stitch length of the second stitch to 12.0. 19. Touch OK to close Design Shaping. 20. Touch Thread Color Edit. Select color 2:1, and then touch Quick Color

Change. Select the gold in the last row, last column. Touch OK to close the pop- up, and then touch OK to close Thread Color Edit.


21. Touch Design Shaping. 22. Select Circle Counterclockwise. Set the Number of Objects to 6. Touch OK

to close the pop-up. 23. Touch Select Side Positioning, and choose Rotated 90° CW. Touch OK to

close the pop-up. 24. Scale to 30.5. 25. Touch Rotate, and rotate the design to center the shorter spokes between the

longer spokes. 26. Touch OK to close Design Shaping. 27. Touch the Stitch Menu. Select the X Menu. Touch and hold Delete to remove

the Fix stitches. 28. Select stitch X1:7. Change the stitch length to 9.0 and stitch width to 6.0. Touch

OK to exit Program mode. 29. Touch Scale and enlarge the size to 10.0 x 6.7. 30. Touch Thread Color Edit. Select color 3:1, and then touch Quick Color

Change. Choose the gold color in the last row, last column. Touch OK to close the pop-up, and then touch OK to close Thread Color Edit.

31. Touch Zoom Options, and then touch Zoom to Box. Click, hold and drag a very small box around the center of the design.

32. Move the candlewick stitch to center the body of the stitch in the center of the snowflake spokes.

33. Touch Zoom Options, and then Zoom to Hoop. 34. Touch the Stitch Menu. Select the X Menu. Touch and hold Delete to remove

the Fix stitches. 35. Select stitch X1:7. Leave all settings at default. Touch OK. 36. Touch Thread Color Edit. Select color 4:1, and then touch Quick Color

Change. Choose the same gold color in the last row, last column. Touch OK to close the pop-up, and then touch OK to close Thread Color Edit.

37. Touch Design Shaping. Choose Circle Clockwise. 38. Set Number of Objects to 6. Touch OK to close the pop-up. 39. Touch Select Side Positioning, and choose Rotated 90° CW. Touch OK to

close the pop-up. 40. Scale inward until the circle is very near the tip of the shorter snowflake spoke. 41. Touch Rotate and rotate the stitches to place each candlewick stitch at the tip of

the shorter point. 42. Touch OK to close Design Shaping.


43. Touch Save to My Designs, browse to your USB stick if necessary. Touch Rename File or Folder. Touch and hold Delete to clear the name field, and name the design Ornament 2.vp3. Touch OK to accept the new name, and touch OK to save the design.

44. Touch and hold Delete to clear the embroidery field. Touch OK to accept.

Ornament 3 (L Menu Snowflake) 1. Touch the Stitch Menu. Select stitch L1:6. Set the stitch length to 36.0 and the

width to 5.5. 2. Touch ALT, and set the density to 0.2. 3. Touch OK to exit Programming. 4. Touch Thread Color Edit. Select color 1:1, then touch Quick Color Change.

Select the gold color in the last row, next to the last column. Touch OK to close the pop-up, and then touch OK to close Thread Color Edit.

5. Touch Design Shaping. Select Circle Clockwise. 6. Set Number of Objects to 6 and touch OK to close the pop-up. 7. Touch Select Side Positioning, and choose Rotated 90° CCW. 8. Scale to 36.0. 9. Touch Rotate, and rotate the design to 351°. 10. Touch OK to close Design Shaping. 11. Touch Stitch Menu. Select stitch L1:6 again. Set the stitch length to 24.0 and

the stitch width to 5.5. Touch OK to close Programming. 12. Touch Thread Color Edit. Select color 2:1, then touch Quick Color Change.

Select the brown in the last row, first column. Touch OK to close the pop-up, then touch OK to close Thread Color Edit.

13. Touch Design Shaping. Choose Circle Clockwise. 14. Set Number of Objects to 6 and touch OK to close the pop-up. 15. Touch Select Side Positioning, and choose Rotated 90° CCW. 16. Scale to 26.


17. Touch Rotate, and rotate to center the shorter spokes between the longer spokes of the snowflake.

18. Touch OK to close Design Shaping. 19. Touch Stitch Menu. Select stitch C1:5. Set the stitch length to 3.0 and the stitch

width to 6.0. 20. Touch ALT, and change the density to 0.2. 21. Touch Duplicate, then Mirror End to End. 22. Touch OK to close Programming 23. Touch Thread Color Edit. Select color 3:1, then touch Quick Color Change

and select the medium brown in the last row, fifth column. Touch OK to close the pop-up, and touch OK to close Thread Color Edit.

24. Touch Position, then touch Center in Hoop. 25. Touch Save to My Designs. Touch USB peripheral devices. Touch and hold

your USB embroidery stick to open it. 26. Touch Rename File or Folder. Touch and hold Delete to clear the name field.

Name the design Ornament 3.vp3. Touch OK to accept the name, and touch OK to save the design.


Ornament 4 (Raw Edge Applique) 1. Touch Stitch Menu. Touch A Menu to open Program mode. 2. Touch and hold Delete to remove the Fix stitches. 3. Select stitch A1:8. Change the stitch length to 3.5. 4. Touch OK to exit Program mode. 5. Touch Thread Color Edit. Select color 1:1 and touch Quick Color Change.

Select the red in the 7th row, third column. 6. Touch Design Shaping. Choose Circle Clockwise. 7. Touch Select Spacing, and choose Left Justification. Touch OK to close the

pop-up.


8. Set the Number of Objects to 63. Touch OK. 9. Scale to 70.5. Touch OK to close Design Shaping. Click on the circle to select it

again. 10. Touch Design Shaping. Scale the circle to 70.0 to close the circle. 11. Touch OK to close Design Shaping. 12. Touch Stitch Menu. Select stitch H2:26. Set the stitch length to 50.0 and leave

the width at 7.0. 13. Touch ALT, and change the density to 0.2. 14. Touch OK to exit Program mode. 15. Touch Thread Color Edit. Select color 2:1, and then touch Quick Color

Change. Select the blue in the 5th row, next to the last column. Touch OK to close the pop-up. Touch OK to close Thread Color Edit.

16. Touch Scale, and then touch the padlock to unlock proportional. Scale the width to as wide as it will go (8.4).

17. Touch Rotate, and rotate 90°. 18. Touch Position, and move the scallop to -27 x 0.0. 19. Touch Duplicate. Touch Mirror Side to Side. 20. Move the new scallop to 21.1 x 0.0. 21. Touch Stitch Menu. Select stitch H2:26. Set the stitch length to 65.0 and leave

the width at 7.0. 22. Touch ALT, and change the density to 0.02. 23. Touch OK to exit Program mode. 24. Touch Thread Color Edit. Select color 3.1, and then touch Quick Color

Change. Select the blue in the 5th row, fourth column. Touch OK to close the pop-up. Touch OK to close Thread Color Edit.

25. Touch Scale, and then touch the padlock to unlock proportional. Scale the width to as wide as it will go (8.4).

26. Touch Rotate, and rotate 90°. 27. Touch Mirror Side to Side. 28. Touch Position, and move the scallop to -16.6 x 0.0. 29. Touch Move Design Backward. 30. Touch Duplicate. Touch Mirror Side to Side, and then move the new scallop to

9.7 x 0.0. 31. Touch Move Design Backward to make this last scallop stitch before the top

scallop.


32. Touch Thread Color Edit. Touch color 3:1, and then touch Select Equal. Touch Quick Color Change, and select the same blue as the first and last scallop, the blue in the fifth row, next to the last colmn. Touch OK to close the pop-up, and touch OK to close Thread Color Edit.

33. Touch the Stitch Menu. Touch the K Menu. 34. Touch and hold Delete to remove the Fix stitches. Select stitch K4:57. Change

the stitch length to 25.0, and change the stitch width to 16.0. Touch OK. 35. Touch Thread Color Edit. Select color 6:1, then touch Quick Color Change.

Select any other blue color and touch OK to close the pop-up. Touch OK to close Thread Color Edit.

36. Touch Rotate, and touch Rotate 90° three times to rotate it to 270°. 37. Touch Position, and move the snowflake to -5.6 to 3.8. 38. Touch Duplicate, and move the new snowflake to -2.6 x -20.5. 39. Touch Duplicate, then Mirror Side to Side. 40. Touch Position, and move the new snowflake to -2.6 x 20.5. 41. Touch Save to My Designs. My Designs (or your USB stick) should be active, so

touch Rename File or Folder. Touch and hold Delete to clear the name field. Name the design Ornament 4.vp3. Touch OK to accept the new name, then touch OK to save the design.


Ornament 5 (Candlewick Applique)

1. Touch the Stitch Menu. Select stitch H1:2. Set the stitch length to 70.0 and the

stitch width to 20.0. Touch OK to close Programming. 2. Touch Thread Color Edit. Select color 1:1, and touch Quick Color Change.

Choose the green in the 3rd row, last column. Touch OK to close the pop-up, and touch OK to close Thread Color Edit.

3. Touch Position, and then touch Center in Hoop. 4. Touch Duplicate, and then touch Mirror End to End.


5. Center this stitch as well. (This stitch does not have the ability to change the density. By mirroring it end to end, it offsets the stitches to make the stitch denser).

6. Touch Select All. Touch Group/Ungroup. 7. Move the design to 0.0 x 9.0. 8. Touch Duplicate. Touch Mirror Side to Side, and then move the new design to

0.0 x -9.0. 9. With the grouped scallop design still selected, touch Duplicate. 10. Touch Scale, and then touch the padlock to unlock proportional. Scale the

design to as wide as it will go, 70.0 x 24.0. 11. Touch Position, and move the design to 0.0 x -15.4. 12. Touch Duplicate, and then touch Mirror Side to Side. 13. Touch Position, and move the grouped design to 0.0 x 15.4. 14. Touch Select All. Touch Group/Ungroup. 15. Touch the Stitch Menu. Select stitch C1:18. Change the stitch length to 35.0 and

leave the stitch width at 7.0. 16. Touch ALT, and change the density to 0.2. 17. Touch Duplicate, then Mirror End to End. 18. Touch OK to close Programming. 19. Touch Thread Color Edit. Select color 2:1, and touch Quick Color Change.

Select the green in the 3rd row, 3rd column. Touch OK to close the pop-up, and then touch OK to close Thread Color Edit.

20. Touch Position, and move to 0.0 x -2.8. 21. Touch Duplicate, and then touch Mirror Side to Side. Touch Mirror End to

End. 22. Move the duplicated design to 0.0 x 2.8. 23. With the duplicated design still selected, touch Add/Remove Selection. Touch

Step Through Designs until the other pictogram program is selected. Touch Add/Remove Selection to end the selection process. Touch Group/Ungroup to combine the pair of stitches as a single pattern.

24. Touch Select All, and then touch Group/Ungroup. 25. Deselect everything by touching away from the design. 26. Touch Design Applique. Select Circle, and scale to 72.0 x 72.0. 27. Choose Candlewick Narrow, and then touch OK to accept and close Design

Applique.


28. Touch Thread Color Edit. Select color 2:1. Touch Quick Color Change. Select the white color. Touch OK to close the pop-up.

29. Touch color 2:2. Touch Quick Color Change. Select the off-white. Touch OK to close the pop-up.

30. Touch color 2:3, and then touch Quick Color Change. Select the green in the 3rd

row, 4th column. Touch OK to close the pop-up, and touch OK to close Thread Color Edit.

31. Touch Save to My Designs. Touch and hold the icon for your USB embroidery stick. Touch Rename File or Folder, then touch and hold Delete to clear the name field. Name the design Ornament 5.vp3. Touch OK to accept the new name and touch OK to save the design.


To embroider the designs:

Ornament 1 1. Touch File Manager. 2. Browse to your USB embroidery stick. 3. Load Ornament1. 4. Hoop the 10” x 12” piece of INSPIRA® Whisper Web Mesh stabilizer and

attach to the embroidery unit. 5. Touch GO! to toggle to stitch-out mode. 6. Place the pillow fabric on top of the stabilizer, centered in the hoop. 7. Use Design Positioning to place the center of the design on the center mark on

the fabric. 8. Place the 6” square of INSPIRA® Water Works soluble film on top of the fabric

in the hoop. 9. Touch and hold Baste in Hoop and choose Baste around hoop area. Touch

Start/Stop (or use the foot control) to baste the fabric to the stabilizer. 10. Slide the 6” square of INSPIRA® Tear-A-Way stabilizer under the hoop as

additional stabilizer. 11. Embroider the design with the colors of your choice. 12. When the embroidery is finished, touch OK on the pop-up. Touch Return to

Embroidery Edit. Touch and hold Delete to clear the screen.


13. Remove the hoop from the machine. Turn the hoop over and cut several of the basting stitches, including the corner stitches. Turn the hoop over again and pull on the lower left corner of the basting stitches to pull them out. Cut away as much stabilizer as possible.

Ornament 2 1. Load Ornament2 from your USB embroidery stick. 2. Hoop a 10” x 12” piece of INSPIRA® Whisper Web Mesh stabilizer and

attach to the embroidery unit. 3. Touch GO! to toggle to stitch-out mode. 4. Place the pillow fabric on top of the stabilizer, with the upper left mark centered in

the hoop. 5. Use Design Positioning to place the center of the design on the mark on the

fabric. 6. Place the 6” square of INSPIRA® Water Works soluble film on top of the fabric


Start/Stop (or use the foot control) to baste the fabric to the stabilizer. 8. Slide the 6” square of INSPIRA® Tear-A-Way stabilizer under the hoop for

additional stabilizer. 9. Touch Color Functions. Touch Color Block Merge. 10. Embroider the design with the colors of your choice. 11. When the embroidery is finished, touch OK on the pop-up. Touch Return to

Embroidery Edit. Touch and hold Delete to clear the screen. 12. Remove the hoop from the machine. Turn the hoop over and cut several of the

basting stitches, including the corner stitches. Turn the hoop over again and pull on the lower left corner of the basting stitches to pull them out. Cut away as much stabilizer as possible.


attach to the embroidery unit.


3. Touch GO! to toggle to stitch-out mode. 4. Place the pillow fabric on top of the stabilizer, with the upper right mark centered

in the hoop. 5. Use Design Positioning to place the center of the design on the mark on the

fabric. 6. Place the 6” square of INSPIRA® Water Works soluble film on top of the fabric



additional stabilizer. 9. Touch Color Functions. Touch Color Block Merge. 10. Embroider the design with the colors of your choice. 11. When the embroidery is finished, touch OK on the pop-up. Touch Return to




attach to the embroidery unit. 3. Touch GO! to toggle to stitch-out mode. 4. Place the pillow fabric on top of the stabilizer, with the lower right mark centered

in the hoop. 5. Use Design Positioning to place the center of the design on the mark on the

fabric. 6. Touch and hold Baste in Hoop and choose Baste around hoop area. Touch


additional stabilizer. 8. Touch Color Functions. Touch Color Block Merge.


9. Place the sheer fabric in the center of the hoop. Use the foot control to stitch the first color, keeping the sheer fabric smoothed out as it stitches.

10. Remove the hoop from the machine, and trim fairly close around the stitching. 11. Place the hoop back on the machine. 12. Embroider the rest of the design with the colors of your choice. 13. When the embroidery is finished, touch OK on the pop-up. Touch Return to



Ornament 5 1. Load Ornament5 from your USB embroidery stick. 2. Hoop the 10” x 12” piece of INSPIRA® Whisper Web Mesh stabilizer and

attach to the embroidery unit. 3. Touch GO! to toggle to stitch-out mode. 4. Place the pillow fabric on top of the stabilizer, with the lower left mark centered in

the hoop. 5. Use Design Positioning to place the center of the design on the mark on the

fabric. 6. Touch and hold Baste in Hoop and choose Baste around hoop area. Touch


additional stabilizer. 8. Touch Color Functions. Touch Color Block Merge. 9. On the control panel, scroll down and select the white color. Stitch the color,

using the color of your choice since it will be covered later by the candlewicking stitches.

10. Place the sheer fabric over the stitching. 11. Use the foot control to tack the applique fabric to the pillow fabric with the next

color. 12. Remove the hoop from the machine and trim fairly close around the applique

fabric. Return the hoop to the machine.


13. Jump back to color 1:1. 14. Embroider the design using the colors of your choice until you get back to the

white color stop. Skip that one and the next one as they’ve already been stitched. 15. Change to the color for the candlewick stitches and embroider it. 16. When the embroidery is finished, touch OK on the pop-up. Touch Return to



Complete the Pillow

Once all embroideries are finished and stabilizer trimmed, steam press the designs on a padded surface from the wrong side. 1. Using the Clear Invisible Zipper foot, insert the invisible zipper on the two

backing pieces of pillow fabric. 2. Change to the Clear Open Toe foot. Use stitch A2:38 to secure both ends of the

zipper within the seam allowance. Set aside. 3. Attach the appropriate Ribbon Foot. Insert one of the ribbons into the slot in the

foot. Stitch the ribbon from the top of the pillow to the lower left ornament. Leave a short ribbon tail for now. Repeat this process for the center design and the far right design with different ribbons.

4. Thread yarns into the holes of the 3-Hole Yarn foot. Attach the foot and pick one of the yarn couching stitches in the X menu. Choose thread to coordinate with the yarns, and stitch to the second design.

5. Select stitch A2:38 and stitch to secure the yarn ends. Cut the yarn tails at the stitching.

6. Change yarns and threads if desired. Choose one of the yarn couching stitches from the X menu and stitch to the fourth design.

7. Select stitch A2:38 and stitch to secure the yarn ends. Cut the yarn tails at the stitching.

8. Tack the lower ends of the ribbons using stitch A2:38. Trim the ribbon tails at the stitching.


9. Create bows as demonstrated in the class. Tack a bow to the bottom of each ribbon and yarn stitch.

10. Attach the Button Foot. Use the placement tool to insert the button into the button foot and stitch to secure the bows.

11. Lay the pillow back on a flat surface, right side up. Open the zipper at least 2”. Place the pillow top, right side down, on the pillow back. Pin.

12. Change to the Clear Seam Guide Foot and stitch in place using a ½” seam allowance. Trim the seam allowance and corners if necessary. Turn right side out.

Holiday Ornaments Pillow - Viking Sewing Gallery½ yard fabric A (linen/cotton blend fabric for...

Documents

Transcript of Holiday Ornaments Pillow - Viking Sewing Gallery½ yard fabric A (linen/cotton blend fabric for...