HM-1000 Series User Manual

NO. G03-HM1000-F

Revision: 2.0

Release date: October 1, 2019

Trademark:

* Specifications and Information contained in this documentation are furnished for information use only, and are

subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

i

Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle.

ii

ENVIRONMENTAL SAFETY INSTRUCTION ........................................................................... iii USER’S NOTICE ....................................................................................................................... iv MANUAL REVISION INFORMATION ....................................................................................... iv ITEM CHECKLIST ..................................................................................................................... iv CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD

1-1 PRODUCT FEATURES ............................................................................................... 1 1-2 SPECIFICATION ......................................................................................................... 2 1-3 MAIN BOARD DIAGRAM ........................................................................................... 4

CHAPTER 2 HARDWARE INSTALLATION 2-1 LOCATION OF INTERNAL JUMPER AND CONNECTOR ....................................... 6 2-2 INTERNAL JUMPER AND CONNECTOR SETTING ................................................. 7

2-2-1 CONNECTORS ............................................................................................. 8 2-2-2 HEADERS ..................................................................................................... 10

CHAPTER3 HARDWARE EXPANSION 3-1 EXPANSION SLOT ..................................................................................................... 13 3-2 EXTENSION SLOT ..................................................................................................... 14

CHAPTER 4 INTRODUCING BIOS 4-1 ENTERING SETUP ..................................................................................................... 15 4-2 BIOS MENU SCREEN ................................................................................................ 16 4-3 FUNCTION KEYS ....................................................................................................... 16 4-4 GETTING HELP .......................................................................................................... 17 4-5 MEMU BARS ............................................................................................................... 17 4-6 MAIN MENU ................................................................................................................ 18 4-7 ADVANCED MENU ..................................................................................................... 19 4-8 CHIPSET MENU .......................................................................................................... 24 4-9 BOOT MENU ............................................................................................................... 28 4-10 SECURITY MENU ....................................................................................................... 30 4-11 TURBOOC MENU ....................................................................................................... 31 4-12 SAVE & EXIT MENU ................................................................................................... 34

TABLE OF CONTENT

iii

Environmental Safety Instruction Avoid the dusty, humidity and temperature extremes. Do not place the product in

any area where it may become wet. 0 to 60 centigrade is the suitable temperature. (The figure comes from the request

of the main chipset) Generally speaking, dramatic changes in temperature may lead to contact

malfunction and crackles due to constant thermal expansion and contraction from the welding spots’ that connect components and PCB. Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon. These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components. Suggest starting the computer until the temperature goes up.

The increasing temperature of the capacitor may decrease the life of computer.

Using the close case may decrease the life of other device because the higher temperature in the inner of the case.

Attention to the heat sink when you over-clocking. The higher temperature may

decrease the life of the device and burned the capacitor.

iv

USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.

THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).

PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT INTENT TO INFRINGE.

Manual Revision Information Reversion Revision History Date 2.0 Second Edition October 1, 2019

Item Checklist Motherboard Cable(s) I/O Back panel shield

1

Chapter 1: Introduction

1-1 Product Features Intel® LGA 1150 Socket Core i7/i5/i3 Processor (Max 54W) Onboard 4G DDR3L/1600Mhz DRAM (Max 8GB) 2 x Intel® i211AT 10/100/1000Base-T Ethernet 2 x RS-232/422/485 ports with automatic flow control VGA,HDMI,DP support 3 x independent displays Audio with MIC, Line in, Line out 6 x USB ports (4 x USB3.0) 1 x PCI-E x16 slot, 2 x PCI slots, 1 x extend slot The extend slot can be used to extend 14 x USB3.0 or 4 x Giga LAN or other

functional interfaces Thumb screw for easy maintenance and expansion card installation The lead switch is convenient for the actual field operation 9~36V wide input voltage can meet the needs of different industries

2

1-2 Specification Spec Description

CPU Intel® LGA 1150 Socket Core i7/i5/i3 Processor (Max 54W) Intel® Haswell Q87 chip (HM-1000) / Intel® Haswell H81

chip (HM-1100)

Memory 1* DDR3L SO-DIMM slot Support DDR3L 4GB DDR3L/1600 MHz SDRAM, expandable to

8GB Expansion Slot 1* Full-size Mini-PCIE slot

Storage 1* built-in 2.5” SATA HDD bracket

LAN Chip 2* Intel® i211AT GbE Support Fast Ethernet LAN function of providing

10/100/1000Mbps Ethernet data transfer rate

Audio Chip Realtek ALC662 HD Audio Codec integrated Audio driver and utility included

BIOS AMI 64MB Flash ROM

Rear I/O

1* 3 Pin power connector, terminal Block with lock 2* RS-232/422/485 with DB9 connectors, automatic RS-485 data

flow control 1* DP 1.2 support 1920 x 1080@60Hz 1* HDMI 1.4a support 1920 x 1080@60Hz 1* VGA support 1920 x 1200@60Hz 1* PS/2 Keyboard & Mouse port 4* USB3.0, 2* USB2.0 ports 2* RJ45, 10/100/1000 Mbps 1* MIC, Line-in, Line-out port 1* Power Button, 1* Reset Button

Internal I/O

1* USB 2.0 header 1* CPU / Chassis Fan connectors 1* 2-pin HDMI header 1* Audio header

3

1* Mini PCIe connector 1* PCIe x16 connector 1* M.2 Connector(2260/80) 2* SATA3 Connector 1* AT_ATX Mode header 1* Front panel header 1* SIM Card socket

4

1-3 Main Board Diagram: Front

Intel CPU

9~36V DC-in

Connector

Top: DP

Bottom: HDMI

Top: PS/2 Connector

Middle/Bottom: USB 2.0 Ports

Top: RJ-45

LAN Port2

Middle/Bottom: USB3.0 Ports

Top: Line-In Middle: Line-Out

Bottom: MIC

Power ON/OFF

CPUFAN Header

Top: COM1

Bottom: COM2

Top: RJ-45

LAN Port1

Middle/Bottom: USB3.0 Ports

VGA Connector

SYSFAN1 Header

JW_FP Header

AT_ATX_MODE Header

F_USB1 Header

HDMI_SPDIF Header

FP_AUDIO Header

SIM Card Socket

5

Main Board Diagram: Back

Mini PCIe Connector

M.2 Connector

SATA3 Connector

PCIe Connector

6

Chapter 2 Hardware Installation

2-1 Location of Internal Jumper and Connector

Intel CPU

9~36V DC-in

Connector

Top: DisplayPort

Bottom: HDMI

Top: PS/2 Connector

Middle/Bottom: USB 2.0 Ports

Top: RJ-45

LAN Port2

Middle/Bottom: USB3.0 Ports

Top: Line-In Middle: Line-Out

Bottom: MIC

Power ON/OFF

CPUFAN Header

Top: COM1

Bottom: COM2

Top: RJ-45

LAN Port1

Middle/Bottom: USB3.0 Ports

VGA Connector

SYSFAN1 Header

JW_FP Header F_USB1 Header

HDMI_SPDIF Header

FP_AUDIO Header

SIM Card Socket JP1

AT_ATX_MODE

JBAT

7

2-2 Internal Jumper and Connector Setting (1) DCIN936 (3-pin): 9~36V Power Select

(2) JP1 (4-pin): COSE_OPEN and PWROK_DISABLED Select

3-4 PWROK_DISABLED. 1-2 COSE_OPEN;

3 4

2 1

3 4

2 1

(3) AT_ATX_MODE (3-pin): AT/ATX Mode Select

V+

V-

GN

D

2-3 Close: AT_Mode.

1-2 Close: ATX_Mode (Default);

3 1

3 1

*ATX Mode Selected: Press power button to power on after power input ready; AT Mode Selected: Directly power on as power input ready.

8

(4) FPW_SW (2-pin): Power ON/OFF Select

2-2-1 Connectors (1) Rear I/O Connectors

Icon Name Function

9~36V DC-in Power Connector

For user to connect compatible power adapter to provide power supply for the system.

COM1

Blue:Line-IN Green:Line-OUT Pink:MIC

9~36V DC-in

Connector

PS/2

HDMI

VGA

GN

D

FPSPSW

COM2 USB 3.0 Port

DP

USB 2.0 Port

RJ-45 LAN1 Port

RJ-45 LAN2 Port

Power ON/OFF

9

Serial Port Mainly for user to connect external MODEM or other devices that supports Serial Communications Interface.

DP

To the system to corresponding display device with compatible DP cable. (Max. resolution Support : 1920*1080 @60

Hz)

HDMI Port To connect display device that support HDMI specification. (Max. resolution Support : 1920*1080

@60Hz)

PS/2 Port

Keyboard and Mouse port.

USB 2.0 Port To connect USB keyboard, mouse or other

devices compatible with USB specification.

RJ-45 LAN Port

This connector is standard RJ-45 LAN jack for Network connection.

USB 3.0 Port

To connect USB keyboard, mouse or other devices compatible with USB specification. USB 3.0 ports supports up to 5Gbps data transfer rate.

RJ-45 LAN Port

This connector is standard RJ-45 LAN jack for Network connection.

Audio Connectors

BLUE : Line-in Connector GREEN : Line-out Connector PINK : MIC Connector

10

VGA Port

To connect display device that support VGA specification.

Power ON/OFF

To select power ON and OFF.

2-2-2 Headers (1) CPUFAN (4-pin): CPUFAN Header

(2) SYSFAN1 (3-pin): System Fan Header

1 SYS FAN1 3 Fan Clock

+12V Fan Power GND

11

(3) JW_FP1 (9-pin): Front Panel Header

GN

D

HD

D LE

D-

GN

D

RS

SE

T-

PW

RS

W-

VC

C

PW

R LE

D+

PW

R LE

D-

HD

D LE

D+

Pin 1

(4) F_USB1 (9-pin): USB Port Header

Pin 1

SBV1

L_USBP7-

GND L_USBP7+

SBV1

NC

L_USBP6-

GND L_USBP6+

Pin 2

12

(5) HDMI_SPDIF (2-pin): HDMI-SPDIF Out header

Pin1 S

PD

IF

GN

D

(6) FP_AUDIO (10-pin): Line-Out, MIC-In Header This header connects to Front Panel Line-out, MIC-In connector with cable.

Pin 1

MIC2-L

LINEOUT2-L

MIC2-R LINEOUUT2-R

SENSE_B

GND

NC

AUD_JD

2

9 10

NC

13

Chapter 3 Hardware Expansion

3-1 Expansion Slot HM-1000 series offer 4* PCIex1 and 2 * COM expansion slots.

Expansion Slot 1 Expansion Slot 2 Expansion Slot 3

Expansion Slot 4

14

3-2 Extension Slot HM-1000 series offer 1* PCIex16, 2 * PCI and 1 * USB2.0 extension slots.

1 * USB2.0

1 * PCIex16

2 * PCI

15

Chapter 4 Introducing BIOS

Notice! The BIOS options in this manual are for reference only. Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard. Users are welcome to download the latest BIOS version form our official website.

The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program will gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). Since the BIOS is the only channel for hardware and software to communicate, it is the key factor for system stability, and in ensuring that your system performance as its best.

4-1 Entering Setup Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the “RESET” button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to Press <Del> to enter Setup

16

4-2 BIOS Menu Screen The following diagram show a general BIOS menu screen:

BIOS Menu Screen

4-3 Function Keys In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here: Press←→ (left, right) to select screen; Press ↑↓ (up, down) to choose, in the main menu, the option you want to confirm or

to modify.

Menu Bar

Menu Items

Current Setting Value

Function Keys

General Help Items

17

Press <Enter> to select. Press <+>/<–> keys when you want to modify the BIOS parameters for the active

option. [F1]: General help. [F2]: Previous value. [F3]: Optimized defaults. [F4]: Save & Reset. Press <Esc> to quit the BIOS Setup.

4-4 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the top right corner the screen.

Status Page Setup Menu/Option Page Setup Menu Press [F1] to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>. 4-5 Menu Bars There are six menu bars on top of BIOS screen:

Main To change system basic configuration Advanced To change system advanced configuration Chipset To change chipset configuration Security Password settings Boot To change boot settings Save & Exit Save setting, loading and exit options.

User can press the right or left arrow key on the keyboard to switch from menu bar. The selected one is highlighted.

18

4-6 Main Menu Main menu screen includes some basic system information. Highlight the item and then use the <+> or <-> and numerical keyboard keys to select the value you want in each item.

System Date Set the date. Please use [Tab] to switch between date elements. System Time Set the time. Please use [Tab] to switch between time elements.

19

4-7 Advanced Menu

ACPI Settings

Press [Enter] to make settings for the following sub-item: Enable Hibernation Use this item to select system ability to Hibernate (OS/S4 Sleet State). The optional settings are: [Disabled]; [Enabled]. ACPI Sleep State Use this item to select the highest ACPI sleep state the system will enter when the suspend button is pressed. The optional settings are: [Suspend Disabled]; [S1 only (CPU Stop Clock)]; [S3 (Suspend to RAM)]. ERP Support Use this item to disable or enable ERP to active all wake-up functions.

20

The optional settings are: [Disabled]; [Enabled]. Wake-Up by PCIE/Lan Use this item to disable or enable PCIE Device PME in S1/S3/S4/S5. The optional settings are: [Disabled]; [Enabled]. Wake-Up by PS/2 keyboard Use this item to disable or enable PS/2 keyboard Wake-up from S3/S4/S5. The optional settings are: [Disabled]; [Enabled]. Wake-Up by PS/2 mouse Use this item to disable or enable PS/2 mouse Wake-up from S3/S4/S5. The optional settings are: [Disabled]; [Enabled]. PWRON After PWR-Fail Use this item to select the power supply status. The optional settings are: [Former-Sts]; [Always On]; [Always Off]. [Former-Sts]: Remain the status when power is restored. [Always On]: Device will automatically start up when power is restored. [Always Off]: Device will remain powered off even when power is restored. USB2_PS2 StandBy Power Support` Use this item to disable or enable USB2_PS2 StandBy Power. The optional settings are: [Disabled]; [Enabled].

RTC WakeUp Settings Press [Enter] to make settings for the following sub-item: Wake System with Fixed Time Use this item to enable or disable system wake-up on alarm event. The optional settings: [Disabled]; [Enabled]. When set as [Enabled], system will wake on the Hour/Minute/Second specified. Wake System with Dynamic Time Use this item to enable or disable system wake-up on alarm event. The optional settings: [Disabled]; [Enabled]. When set as [Enabled], system will wake on the (Current time) + (Increased minute(s)).

SATA Configuration Press [Enter] to make settings for the following sub-items: SATA Controller(s)

21

The optional settings are: [Enabled]; [Disabled]. SATA Mode Selection The optional settings are: [IDE]; [AHCI]. SATA Controller Speed The item is for user to set the maximum speed the SATA controller can support. The optional settings are: [Default]; [Gen1]; [Gen2]; [Gen3]. M.2

Port Support The optional settings are: [Disabled]; [Enabled]. SATA Device Type The optional settings are: [Hard Disk Drive]; [Solid State Drive].

SATA Port Port Support The optional settings are: [Disabled]; [Enabled]. Hot Plug The optional settings are: [Disabled]; [Enabled]. SATA Device Type The optional settings are: [Hard Disk Drive]; [Solid State Drive].

► PCH-FW Configuration Press [Enter] to see Management Engine Technology Parameters information. ME FW Image RE-Flash Use this item to enable or disable ME FW Image Re-Flash function. The optional settings are: [Disabled]; [Enabled].

USB Configuration Press [Enter] to make settings for the following sub-items: Legacy USB Support The optional settings are: [Enabled]; [Disabled]; [Auto]. [Enabled]: To enable legacy USB support. [Disabled]: To keep USB devices available only for EFI specification, [Auto]: To disable legacy support if no USB devices are connected. XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.

22

The optional settings are: [Enabled]; [Disabled]. EHCI Hand-off This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. The optional settings are: [Disabled]; [Enabled]. USB Mass Storage Driver Support The optional settings are: [Disabled]; [Enabled]. USB Transfer time-out Use this item to set the time-out value for control, bulk, and interrupt transfers. The optional settings are: [1 sec]; [5 sec]; [10 sec]; [20 sec]. Device reset time-out Use this item to set USB mass storage device start unit command time-out. The optional settings are: [10 sec]; [20 sec]; [30 sec]; [40 sec]. Device Power-up Delay Use this item to set maximum time the device will take before it properly reports itself to the host controller. ‘Auto’ uses default value: for a root port it is 100 ms, for a hub port the delay is taken from hub descriptor. The optional settings: [Auto]; [Manual]. Select [Manual] you can set value for the following sub-item: ‘Device Power-up Delay in Seconds’. Device Power-up Delay in Seconds The delay range is from [1] to [40] seconds, in one second increments.

► Super I/O Configuration Press [Enter] to make settings for the following sub-items:

► Serial Port 1 Configuration Press [Enter] to make settings for the following items:

Serial Port Use this item to enable or disable serial port (COM). The optional settings are: [Disabled]; [Enabled]. Change Settings Use this item to select an optimal setting for super IO device. The optional settings are: [Auto]; [IO=3F8h; IRQ=4;]; [IO=3F8h; IRQ=3,4,5,6,7,10,11;]; [IO=2F8h; IRQ=3,4,5,6,7,10,11;]; [IO=3E8h;

23

IRQ=3,4,5,6,7,10,11;] ; [IO=2E8h; IRQ=3,4,5,6,7,10,11;]. Transmission Mode Select Use this item to select transmission mode. The optional settings are: [RS422]; [RS232]; [RS485].

► Serial Port 2 Configuration Press [Enter] to make settings for the following items:

Serial Port Use this item to enable or disable serial port (COM). The optional settings are: [Disabled]; [Enabled]. Change Settings Use this item to select an optimal setting for super IO device. The optional settings are: [Auto]; [IO=2F8h; IRQ=3;]; [IO=3F8h; IRQ=3,4,5,6,7,10,11;]; [IO=2F8h; IRQ=3,4,5,6,7,10,11;]; [IO=3E8h; IRQ=3,4,5,6,7,10,11;] ; [IO=2E8h; IRQ=3,4,5,6,7,10,11;]. Transmission Mode Select Use this item to select transmission mode. The optional settings are: [RS422]; [RS232]; [RS485].

WatchDog Timer The optional settings are: [Disabled]; [Enabled]. When user set it as [Enabled], the following items will show up for user to make further settings:

WatchDog timer Value: The temperature range is from [1] to [255]. WatchDog timer Unit: The optional settings are [Sec.]; [Min.].

Case Open Detect Use this item to detect case has already open or not, and show message in POST. The optional settings are: [Disabled]; [Enabled]. PS2 KB/MS Connect Use this item to select PS2 Connect Primary Devices. The optional settings are: [Keyboard First]; [Mouse First].

F81866 H/W Monitor Press [Enter] to make settings for the following sub-item: Shutdown Temperature Configuration

24

Use this item to select system shutdown temperature. The optional settings are: [Disabled]; [60C/140F]; [65C/149F]; [70C/158F]; [75C/167F]; CPUFAN Smart Mode The optional settings are: [Disabled]; [Enabled]. Select [Enabled] you can set value for the following sub-item: CPUFAN Highest speed Temp The temperature range is from [Min>=Idel Temp.] to [Max=100C]. CPUFAN Idle Temp The idel speed temperature range is from [Min=0C.] to [Max<=Full-speed Temp].

4-8 Chipset Menu

PCH-IO Configuration

25

USB Configuration Press [Enter] to view current using memory information and make settings for the following sub-items: USB Precondition Use this item to enable or disable precondition work on USB host controller and root ports for faster enumeration. The optional settings are: [Disabled]; [Enabled]. XHCI Mode Use this item to selectmode of operation of XHCI controller. The optional settings are: [Smart Auto]; [Auto]; [Enabled]; [Disabled]; [Manual].

When user set it as [Disabled], the following items will show up for user to make further settings:

EHCI1: Use this item to control the USB EHCI (USB 2.0) functions. One EHCI controller must always be enabled. The optional settings are [Disabled]; [Enabled]. EHCI2: Use this item to control the USB EHCI (USB 2.0) functions. One EHCI controller must always be enabled. The optional settings are [Disabled]; [Enabled].

Select [Manual] you can set value for the following sub-item: XHCI Pre-Boot Driver The optional settings are: [Enabled]; [Disabled]. Route USB 2.0 pins to which HC? The optional settings are: [Route Per-Pin]; [Route all Pins to EHCI]; [Route all Pins to XHCI]. When user set it as [Route Per-Pin], the following items will show up for user to make further settings:

USB 2.0 PIN #1 / #2 / #3 / #4 / #5 / #6 / #7 / #8 / #9 / #10 / #11 / #12 / #13: The optional settings are [Route to EXCI]; [Route to XHCI].

Enable USB 3.0 pins The optional settings are: [Select Per-Pin]; [Disabled all Pins]; [Enable all Pins]. When user set it as [Select Per-Pin], the following items will show up for user to make further settings:

USB 3.0 PIN #1 / #2 / #3 / #4 / #5 / #6: The optional settings are [Disabled]; [Enabled].

26

USB Ports Per-Port Disable Control The optional settings are: [Disabled]; [Enabled]. Select [Enabled] you can set value for the following sub-item:

USB Port 1/2/3/4/5/6/7/8/9/10/11/12/13/14 and USB30 Port 1/2/3/4/5/6 The optional settings are: [Disabled]; [Enabled].

Onboard PCIE Lan1 Use this item to enable or disable PCI Express Root Port. The optional settings are: [Disabled]; [Enabled]. Onboard PCIE Lan2 The optional settings are: [Disabled]; [Enabled]. Onboard Lan BootROM Use this item to enable or disable Boot Option ROM for Onboard Network Devices. The optional settings are: [Disabled]; [Enabled]. Azalia Use this item to select detection of the Azalia device. The optional settings are: [Disabled]; [Enabled].

Azalia Internal HDMI Codec Use this item to enable or disable internal HDMI codec for Azalia. The optional settings are: [Enabled]; [Disabled].

► System Agent (SA) Configuration Press [Enter] to make settings for the following sub-items: VT-d Use this item to enable or disable VT-d function on MCH. The optional settings are: [Disabled]; [Enabled]. Internal Graphics The optional settings are: [Auto]; [Disabled]; [Enabled]. [Auto]: Auto Disable Internal Graphics if detect PCIE VGA card. [Enable]: Always Enable Internal Graphics. [Disable]: Always Disable Internal Graphics. Aperture Size The optional settings are: [128MB]; [256MB]; [512MB]. DVMT Pre-Allocated Use this item to select DVMT 5.0 pre-allocated (fixed) graphics memory size used by the internal graphics device.

27

The optional settings are: [32M]; [64M]; [96M]; [128M]; [160M]; [192M]; [224M]; [256M]; [288M]; [320M]; [352M]; [384M]; [416M]; [448M]; [480M]; [512M]; [1024M]. DVMT Total Gfx Mem Use this item to select DVMT 5.0 total graphics memory size used by the internal graphics device. The optional settings are: [128M]; [256M]; [MAX]. RC6 (Render Standby) The optional settings are: [Disabled]; [Enabled]. DMI Link ASPM Control Use this item to enable or disable the control of Active State Power Management on SA side of the DMI Link. The optional settings are: [Disabled]; [L0s]; [L1]; [L0sL1]. DMI Gen 2 Use this item to enable or disable DMI Gen2/nAuto means Disabled for IVB A0 MB/DT and IVB B0 MB, Enabled for other CPUs. The optional settings are: [Auto]; [Enabled]; [Disabled]. Enable PEG The optional settings are: [Disabled]; [Enabled]; [Auto].

PEG – Gen X Use this item to configure PEG B0:D1:F0 Gen1-Gen3.

The optional settings are: [Auto]; [Gen1]; [Gen2]; [Gen3]. Detect Non-Compliance Device The optional settings are: [Disabled]; [Enabled]. PEG – ASPM Use this item to select ASPM support for the PEG Device. This has no effect if PEG is not the currently active device. The optional settings are: [Disabled]; [Auto]; [ASPM L0s]; [ASPM L1]; [ASPM L0sL1]. Select [ASPM L0s] and [ASPM L0sL1] you can set value for the following sub-item:

ASPM L0s Use this item to enable PCIe ASPM L0s. The optional settings are: [Root Port Only]; [Endpoint Port Only]; [Both Root and Endpoint Ports].

Primary IGFX Boot Display

28

The optional settings are: [VBIOS default]; [CRT]; [HDMI1 Only]; [DP Only]. When user set it as [CRT]; [HDMI1 Only]; [DP Only], the following items will show up for user to make further settings:

Secondary IGFX Boot Display The optional settings are: [Disabled]; [CRT]; [HDMI1 Only]; [DP Only].

4-9 Boot Menu

Boot Configuration

► Setup Prompt Timeout Use this item to set number of seconds to wait for setup activation key. ► Bootup Numlock State Use this item to select keyboard NumLock state.

29

The optional settings are: [On]; [Off]. ► Fast Boot The optional settings are: [Disabled]; [Enabled]. When user set it as [Enabled], the following items will show up for user to make further settings:

SATA Support The optional settings are: [Last Boot HDD Only]; [All Sata Devices]; [HDD Only]. VGA Support When user set it as [Auto], only install Legacy OpRom with Legacy OS and logo would NOT be shown during post. Efi driver will still be installed with EFI OS. The optional settings are: [Auto]; [EFI Driver]. USB Support The optional settings are: [Disabled]; [Full Initial]; [Partial Initial]. [Disabled]: All USB devices will not be available until after OS boot. [Full Initial]: USB Mass storage and specific USB port/device will NOT be available before OS boot. [Partial Initial]: All USB devices will be available in OS and Post. PS2 Devices Support The optional settings are: [Disabled]; [Enabled]. NetWork Stack Driver Support The optional settings are: [Disabled]; [Enabled].

Boot Option Priorities ► Boot Option #1 Use this item to select the system boot order. The optional settings are: [P0: SandDisk SD6SP1M128G1012]; [Disabled]. ► Hard Drive BBS Priorities Use this item to select order of the legacy devices in this group. The optional settings are: [P0: SandDisk SD6SP1M128G1012]; [Disabled]. ► CSM parameters Use this item to control CSM launched.

Launch CSM The optional settings are: [Enabled]; [Disabled]. Boot option filter

30

The optional settings are: [UEFI and Legacy]; [Legacy only]; [UEFI only]. Launch Storage OpROM policy The optional settings are: [Do not launch]; [UEFI only]; [Legacy only]. Launch Video OpROM policy The optional settings are: [Do not launch]; [UEFI only]; [Legacy only]; [Legacy first]; [UEFI first]. Other PCI device ROM priority The optional settings are: [UEFI OpROM]; [Legacy OpROM].

4-10 Security Menu

Security menu allow users to change administrator password and user password settings.

31

4-11TurboOC Menu

CPU Configuration Press [Enter] to view current CPU configuration and make settings for the following sub-items: Hyper-threading The optional settings: [Disabled]; [Enabled]. This item should be set as [Enabled] for Windows XP and Linux. Active Processor cores Use this item to select number of cores to enable in each processor package. The optional settings: [All]; [1]. Limit CPUID Maximum The optional settings are: [Disabled]; [Enabled]. This item should be set as [Disabled] for Windows XP. Execute Disable Bit

32

The optional settings: [Disabled]; [Enabled]. Intel Virtualization Technology The optional settings: [Disabled]; [Enabled]. When set as [Enabled], a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. EIST Use this item to enable or disable Intel SpeedStep. The optional settings: [Disabled]; [Enabled]. When set as [Enabled], the following items will show up for user to make further settings:

Turbo Mode The optional settings: [Disabled]; [Enabled].

Turbo Core Ratio Limit Use this item to setup Turbo Core Ratio. [0] means using the factory-configured value.

CPU C State Use this item to enable or disable CPU C state. The optional settings: [Disabled]; [Enabled]. When set as [Enabled], user can see Enhanced C1 state: Enhanced C1 state Use this item to enable or disable CPU C1 state. The optional settings: [Disabled]; [Enabled]. CPU C3 Report The optional settings: [Disabled]; [Enabled]. CPU C6 Report The optional settings: [Disabled]; [Enabled].

C6 Latency The optional settings: [Short]; [Long].

CPU C7 Report The optional settings: [Disabled]; [CPU C7]; [CPU C7s].

C7 Latency The optional settings: [Short]; [Long].

► Memory Configuration Press [Enter] to make settings for the following sub-items:

33

DIMM profile Use this item to select DIMM timing profile that should be used. The optional settings are: [Default DIMM profile]; [Custom Profile]. When set as [Custom Profile], the sub-item ‘Custom Profile Control’ will appear for user to manually set memory timing configuration. Memory Frequency Limiter Use this item to set maximum memory frequency selection in Mhz. This item will not show on the screen when ‘DIMM Profile’ is set as: [Custom Profile]. The optional settings are [1066]; [1333]; [1600]. tCL The Cas Latency Range is from [4] to [18]. tRCD The Row to Col Delay Range is from [1] to [38]. tRP The Ras Precharge Range is from [1] to [38]. tRAS The Ras Active Time Range is from [1] to [586]. tWR The Min Write Recovery Time Range is from [1] to [38]. tRFC The Min Refresh Recovery Delay Time Range is from [1] to [9363]. tRRD The Min Row Active to Row Active Delay Time Range is from [1] to [38]. tWTR The Min Internal Write to Read Command Delay Time Range is from [1] to [38]. tRTP The Min Internal Read to Precharge Command Delay Time Range is from [1] to [38]. tRC The Min Active to Active/Refresh Delay Time (tRCmin) Range is from [1] to [586]. tFAW The Min Four Active Window Delay Time Range is from [1] to [586]. tCWL Use this item to setup Minimum CAS Write Latency Time (tCWLmin).

34

tREFI Use this item to setup Maximum tREFI Time (Average Periodic Refresh Interval). Command Rate Use this item to setup Memory Command Rate Option. The optional settings are [Auto]; [1T]; [2T].

4-12 Save & Exit Menu

Save Changes and Reset

This item allows user to reset the system after saving the changes. Discard Changes and Reset

This item allows user to reset the system without saving any changes. Save Options

35

Save Changes This item allows user to save changes done so far to any of the setup options.

Discard Changes This item allows user to discard changes done so far to any of the setup options.

Restore Defaults Use this item to restore /load default values for all the setup options.

Save as User Defaults Use this item to save the changes done so far as user defaults.

Restore User Defaults Use this item to restore defaults to all the setup options. Boot Override

P0: Sandisk SD6SP1M128G1012 Launch Internal EFI shell application (shell.efi).

Launch EFI Shell from filesystem device Use this item to Launch EFI Shell application (Shellx64.efi) from one of the available filesystem devices.