OPERATION MANUAL

HIGH RESOLUTION VANDAL DOME CAMERA

M099-VDE101-004

Thank you for choosing our high qual i ty camera. Before at tempt ing to connect or operate, p lease read and fol low these instruct ions.

CONTENTS

1. Cautions2. Features3. Equipment and Accessories4. Overview and function5. Instal lat ion6. Connection7. Dimensions8. Specif ications9. OSD Menu Structure

3

1. CAUTIONS

4

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions;

1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.

NoteThis equipment has been tested and found to comply with limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio / tv technician for help.

CautionAny changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1. A regulated DC12V 1A power supply is recommended for use with this camera for the best picture and the most stable operation. An unregulated power supply can cause damage to the camera. When unregulated power supply is applied, product warranty will be out of subject.2. It is recommended that the camera is used with a monitor that has a CCTV quality 75 video impedance level. If your monitor is switched to high impedance then please adjust accordingly.3. Do not attempt to disassemble the camera to gain access to the internal componets. Refer servicing to your dealer.4. Never face the camera towards the sun or any bright or reflective light, which may cause smear on the picture and possible damage to the CCD.5. Do not remove the serial sticker for the warranty service.6. Do not expose the camera to rain or other types of liquid.7. The apparatus must be connected to a mains socket-outlet with a protective earthing connection.

1. CAUTIONS

5

Correct Disposal of This Product(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.Household users should contact either the retailer where they for disposal.

2.Features• 1/3 960H SONY EXview HAD CCD II• High Resolution of 700TV Lines• OSD Function• Multi Language (ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN / PORTUGUESE / SPANISH / CHINESE)

• 2DNR• Privacy Zone• Motion Detect• DC12V / AC24V Dual Voltage• ATR(Adaptive Tone-curve Reproduction / Digital WDR)The function provides gradation compensation to improve the contrast of subjects both low-luminance areas and high luminance areas exist in the same picture

• 3-Axis Gimbal

CAUTION panning the bracket in excess of 3 rotations in one direction maycause damage to the cable.

• Service Video connectorThe Service Video Connector also provides the installer with an easy way of configuring the camera.

6

Pan Rotation Horizontal RotationTilt Rotation

3. Equipment and Accessories

1 VANDAL DOME CAMERA

2 SURFACE MOUNT

3 VIDEO OUTPUT TEST CABLE

4 OPERATION MANUAL

5

SCREW(M4x10) - 4eaSCREW(5x30) - 4eaSCREW(M4x40.SUS) - 4ea

L WRENCH - T20

6 MOUNT GUIDE

7

4.Overview and function

8

• Led Type

• Standard Type

OSD Joyst ick

OSD Joyst ick

• CONTROL FUNCTION (OSD JOYSTICK)

LEFT

UP

RIGHT

DOWN

5. Installation

9

Standard TypeLED Type

Mount Guide

Lens Zoom Knob

Lens Focus Knob

Separate LED Cover (Sunshield Cover) and adjust LENS ZOOM / FOCUS KNOBAfter setting the LENS, assemble the LED Cover (Sunshield Cover).

① Installation of the camera with SURFACE CASE(using M4x40)② Installation of the camera with SCREWS③ Installation of the camera with JUNCTION BOX

① Installation of the camera on the wall ② Installation of the camera on the 3/4” NPT PIPE ③ Installation of the camera on the JUNCTION BOX

Check the safe wire which should be entirely inserted into camera

housing during locking the dome cover to maintain Waterproof condition.

When using the camera without LED take off the rubber.

NOTE

5. Installation1. Installation of Flush Mount

2. Installation of Surface Mount

PIPE

PIPE

10

6.Connection• MONITOR CONNECTION

• DUAL(DC 12V/AC24V)

• DC 12V

When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.

11

DC12V / AC24VRegulated power supply

Video inBNC Female Video

DC12VRegulated power supply

Video inBNC Female Video

7.DimensionsUnit : mm

12

When you fix the focus around 22.0mm in f9.0-22.0mm Varifocal lens, please set short distance focus approximately 3M and do not set long distance focus

Flush Mount Type

Surface Mount Type

Type A Type B

70 70

Standard Type LED Type

8.SpecificationsSignal Format NTSC PAL

Image Device 1/3˝ 960H SONY EXview HAD CCD II

Scanning System 2:1 Interlace

H.Resolution 700TV Lines

Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz

Total Pixels 1020(H) X 508(V) 1020(H) X 596(V)

Effective Pixels 976(H) X 494(V) 976(H) X 582(V)

Electronic Shutter Speed 1/60 sec 1/50 sec

S/N Ratio More than 50dB(AGC Off)

Gamma r=0.45

Min. Illumination COLOR : 0.05Lux/F1.2, BW : 0.02 Lux/F1.2

Sync System Internal

Video Output 1.0 Vp-p Composite(75Ω)

OSD Built in (Inner Key / Joystick)

BLC OFF / BLC / HLC

White Balance ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH-LOCK

2DNR OFF / ON (Level adjustable)

ATR OFF / ON (Level adjustable)

Function MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN

Privacy Masking 4 Zones

Motion Detection 4 Zones

Day & Night AUTO

Language ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN/PORTUGUESE / SPANISH / CHINESE

IP Rating IP66 (Weatherproof)

PowerConsumption

DC12V DC 12V (±10%) Max.120mA

Dual DC 12V (±10%) Max.150mA , AC 24V (±10%) Max. 2.3W

Operating Temperature -10 ~ +50

Storage Temperature -20 ~ +60

Operating Humidity Less than 80%

Options Dual Power, Fan

Weight • Surface Mount Type A : Approx. 1.38kg / Type B : Approx. 1.1kg• Flush type : Approx. 730g

Dimension(mm) 143.0(Φ) x 104.0(mm)

LED TYPE

PowerConsumption

DC12V DC 12V (±10%) Max. 360mA

Dual DC 12V (±10%) Max 430mA , AC 24V (±10%) Max. 5.2W

Min. Illumination 0 Lux (IR LED ON)

IR LED 850nm, 30ea

IR Beam Range Up to 30M

IR LED Operation On : 1 Lux, Off : 3 Lux

Specifications and designs are subject to change for improving the functionality of this product without notice.

13

9. OSD MENU STRUCTUREMAINMENU

1st SubMENU

2nd Sub MENU

3rd Sub MENU

4th Sub MENU

LENS

MANUAL

AUTO

TYPE DC

MODE AUTO,OPEN,CLOSE

SPEED (000 ~ 255)

RETURN

SHUTTER/ AGC

AUTO

HIGH LUMINANCEMODE SHUT,AUTO IRIS, SHUT+AUTO IRIS

BRIGHTNESS (000 ~ 255)

LOW LUMINANCEMODE AGC,OFF

BRIGHTNESS x0.25,x0.50,x0.75,x1.00

RETURN

MANUAL

MODE SHUT+AGC

SHUTTER

1/50(PAL),1/100(NTSC)1/60(NTSC),1/120(PAL)1/250,1/500,1/10001/2000,1/4000,1/10000

AGC 6,12,18,24,30,36,42,44.8

RETURN

WHITEBAL

ATW

SPEED (000 ~ 255)

DELAY CNT (000 ~ 255)

ATW FRAME x0.50,x1.00,x1.50,x2.00

ENVIRONMENT INDOOR,OUTDOOR

RETURN

PUSH

USER1

B-GAIN (000 ~ 255)

R-GAIN (000 ~ 255)

RETURN

USER2

B-GAIN (000 ~ 255)

R-GAIN (000 ~ 255)

RETURN

ANTI CR

MANUALLEVEL 24 ~ 103

RETURN

PUSH LOCK

BACK LIGHT OFF,BLC,HLC

PICADJUST

MIRROR OFF,ON

BRIGHTNESS (000 ~ 255)

CONTRAST (000 ~ 255)

SHARPNESS (000 ~ 255)

HUE (000 ~ 255)

GAIN (000 ~ 255)

RETURN

ATRON

LUMINANCE LOW,MID,HIGH

CONTRAST LOW,MIDLOW,MID,MIDHIGH,HIGH

RETURN

OFF

*SHUT+IRIS : Both the Shutter and the Mechanical Iris are automatically adjusted according to brightness.*Auto Iris(Default): The Shutter stays at the manually selected value and only the Mechanical Iris adjusts to brightness.

14

9. OSD MENU STRUCTUREMAINMENU

1st SubMENU

2nd Sub MENU

3rd Sub MENU

4th Sub MENU

MOTION DET

ON

DETECT SENSE (000 ~ 127)

BLOCK DISP OFF,ON,ENABLE (CONTROLER)

MONITOR AREA ON,OFF

AREA SEL

1/4, 2/4, 3/4, 4/4

TOP NTSC:(000 ~ 244) / PAL: (000 ~ 288)

BOTTOM NTSC:(000 ~ 244) / PAL: (000 ~ 288)

LEFT NTSC:(000 ~ 474) / PAL: (000 ~ 468)

RIGHT NTSC:(000 ~ 474) / PAL: (000 ~ 468)

RETURN

OFF

NEXT

EXIT

SAVE ALL

PRIVACYON

AREA SEL

1/4, 2/4, 3/4, 4/4

TOP NTSC:(000 ~ 244) / PAL: (000 ~ 288)

BOTTOM NTSC:(000 ~ 244) / PAL: (000 ~ 288)

LEFT NTSC:(000 ~ 474) / PAL: (000 ~ 468)

RIGHT NTSC:(000 ~ 474) / PAL: (000 ~ 468)

COLOR (1 ~ 8)

TRANSP 0.00, 0.50, 0.75, 1.00

MOSAIC OFF,ON

RETURN

OFF

NR

NR MODE OFF,Y,C,Y/C

C LEVEL (000 ~ 015)

Y LEVEL (000 ~ 015)

RETURN

CAMERA ID

ON EDIT MODE

RETURN

OFF

LANGUAGE ENGLISH, 日本語 , DEUTSCH, FRANCAIS, Русский, PORTUGUÊS, ESPAÑOL, 中文

CAMERARESET

BACK

EXIT

SAVE ALL

*Important Note : - Any changes made to the camera sett ings must be saved pr ior to exi t ing the OSD menu. Else al l changes wi l l be discarded.

- By changing the lens opt ion in the OSD from MANUAL to AUTO wi l l automat ical ly change the SHUTTER/AGC sett ing f rom AUTO IRIS to SHUT+AUTO IRIS.(Defaul t :AUTO IRIS)

15