HIGH PERFORMANCE DOOR SOLUTIONS€¦ · • Classroom function is available - manual locking upon...
Transcript of HIGH PERFORMANCE DOOR SOLUTIONS€¦ · • Classroom function is available - manual locking upon...
Technical Details
HIGH PERFORMANCEDOOR SOLUTIONS
NASL-017 04/20/20
91.146.110.198
91.146.110.198
91.146.110.198
91.146.110.198
INTRODUCTION
For over 50 years, Surelock McGill has been known around the world as a leading provider of high performance door hardware and accessories. We design and manufacture locking systems that meet a variety of security, operational and life safety needs.
Our ongoing programs of research, development and testing enable us to meet the changing needs and the latest levels of certification. This dedication to certification and development provides protection against extreme levels of physical attack, blast, ballistics, windstorm and corrosion. Each product has been third party tested and certified to many North American and international standards.
The modular design and flexible operational capabilities of our hardware are reasons why our systems are trusted and installed everywhere from retail chains, banks, data centers, utilities, and embassies across the world. Surelock McGill understands the vital operational requirements of our customers. Our products are designed to meet a tiered or layered security approach for the entire property that includes the perimeter doors/gates, exterior/interior doors, access control/alarm monitoring and life-safety.
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
SR4
SR5
SR6
STATE DEPARTMENT
FE/BRSD-STD-01
5MIN
15MIN
60MIN Blast - For details, contact your sales rep
UL752/EN1522/23 FB1- FB7 & FSG
EN1125/EN179/UL305
UL10C - exceeds 3 hours/BS476 PT22/EN1631-1
Above performance results are based on independent third party testing or assessment on selected doorsets
TESTING AND CERTIFICATION OVERVIEW
SOLUTIONS
GOVERNMENT& DEFENSE
INDUSTRIALPETROCHEM
TRANSPORT COMMERCIAL/RETAIL
Threat: Government and Defense facilities are visible icons and unfortunately have become targets for blast, physical and ballistic attacks.
Challenge: Balance between security and life safety.
Threat: Many industries operate in hazardous environments that require special materials and personnel safety that are not met with commercial grade doors and hardware.
Challenge: Pressure containment, corrosion resistance, blast mitigation and critical life-safety access control require specialized solutions designed by experts with years of experience.
Threat: Uncontrolled access to mass transit through service corridors and tunnels leaves the nation's transportation infrastructure vulnerable to attack and vandalism.
Challenge: Providing required access for service, free escape in the event of emergency, while surviving the harsh environment.
Threat: Unauthorized access to operations, control and equipment rooms could lead to sabotage, destruction, or theft of materials or equipment. The nation's connected infrastructure could be destabilized by physical, ballistic, or explosive attack at any one of these facilities.
Challenge: There is no uniform national security standard. Utilities, communications, and data centers need a modular access control and physical protection that is as diverse as their business.
Threat: New security vulnerabilities are discovered every day. Capabilities and technologies evolve and new materials and methods give criminals and terrorist an edge against current physical security solutions.
Challenge: Continued research, development, testing, and certification to mitigate ever evolving physical security and life-safety risks.
Threat: Simple tools like crowbars, hammers, and screwdrivers can be an effective means to pry open an entry door to grant unauthorized access. This can cost the business owner potentially thousands of dollars in losses and endanger or terrorize the staff.
Challenge: Design a physical security solution when coupled with the building's access control and alarm system provides a level of protection that realistically matches local law enforcements response time.
CRITICALINFRASTRUCTURE
CUSTOMSOLUTIONS
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
SLIMLINE: MULTIPOINT LOCKING
N
C
M
A
E
B
L
A
LE
O
N
P
K
K
C
G
G
I
F
B
H
D D1
R
KI
J
S
J
S
F
GLOSSARY:D1: GUIDE BRACKET E: RESTRAINTF: BASE PLATE G: BASE PLATE
H: BASE PLATE (ANTI THRUST)I: TOP TUBE/RODJ: BOTTOM TUBE/ROD-BOLTK: TUBE CLIP
L: TOP VERTICAL BOLTM: MOUNTING PLATEN: HANDLE PLATEO: FACE PLATE
P: GUIDE PLATE TOP/BOTTOMR: PANIC BARS: LEVER HANDLE
A: CENTER MODULEB: GUIDE BRACKET C: GUIDE BRACKET D: GUIDE BRACKET (SPRING LOADED)
SURFACE MOUNTED MORTISE MOUNTED
The Slimline by Surelock McGill is a high performance, multi-point locking system. Its modular design allows for a near infinite number of options to meet the necessary threat, life-safety, and operational requirements that challenge today’s physical security environment.
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
H28 Stainless round bar
SLIMLINE: PANIC & EMERGENCY EXIT SYSTEM
High performance multi-point bolting mechanism that provides automatic bolting upon door closure offering high security protection with ballistic and blast resistance in one product.
The product is designed to provide single motion egress with a panic bar or lever handle. Optional, exterior locking trim (LEO) is available.
The Slimline has been designed with a common mounting footprint enabling the addition of new modules to upgrade to the latest operational requirements.
OPERATIONSExit - Slimline panic and emergency exit systems are operated using either a lever handle or panic bar to allow single motion egress.Upon door closure the bolts will automatically release and secure the door.
Optional Entry - Passage lever handle or external lockable trim (LEO).
FEATURES• Surface mounted or mortise mounted• Automatic bolting upon door closure• Proven rack & pinion mechanism• 5/8" stainless steel bolts with 1" throw • Choice of exit device operators• Non-handed and suitable for in-swing and out-swing doors• Tested to over 1,000,000 cycles• Suitable for doors 7 feet tall with height extensions available• Optional enhancement packs available for blast applications• Optional bolt status monitoring available• Up to 5 active bolting points• 316 grade stainless steel optional
BENEFITS• Automatic bolting• Life safety device UL305 and BSEN 179/1125 compliant• Tested on specific door assemblies up to 60 minutes of FE/BR and LPS 1175:SR6• Door securely bolted when in closed position• Optional remote monitoring of bolt status• Engineered for longevity and trouble free service
Above performance results are based on independent third party testing or assessment on selected doorsets
ENTRY METHODS:
EXITMETHODS:
Manual Key Override
Panic Bar (meets UL305)
Access Control with Motorized Lock Remote Access with Motorized Lock
Access Control with Motorized Lock Remote Access with Motorized Lock
Straight Lever
Straight Lever
1,000,000C Y C L E S
TESTED TO OVERSEISMIC
TESTED
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2008LPCB Cert No. 516-1
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
SR4
SR5
SR6
STATE DEPARTMENT
FE/BRSD-STD-01
5MIN
15MIN
60MIN
Blast - For details, contact your sales rep
UL752/EN1522/23 FB1- FB7 & FSG
EN1125/EN179/UL305
UL10C - exceeds 3 hours/BS476 PT22/EN1631-1
TECHNICAL DRAWINGS
1591
.5
289
66
76.5146
93.5
46.75
SLIMLINE: PANIC & EMERGENCY EXIT SYSTEM - POPULAR ENHANCEMENTS AVAILABLE
M Electric monitoring of bolt status
M7 Motorized bolt retraction assembly for Slimline exit system
T Auxiliary bolting unit (below handle)
U Auxiliary bolting unit and continue (below handle)
U1 Auxiliary bolting unit and continue (above handle)
H28 Stainless steel round tube panic bar
D01 5/8” 316 S/S bolt enhanced blast level cast guides and brackets 3-point
D02 1” 316 S/S bolt, guides and brackets for high blast levels 3-point
E(n) 3 Foot top rod extension tube (i.e. E2 or E3)
B(n) Spacing off of door; (n) = Number of 1mm increments
CODE
/ DE
SCRI
PTIO
N
SELF-CODING SYSTEMThe Slimline (SL) modular devices have a simple ordering code that covers the chosen methods of entry and exit, followed by additional enhancements to further customize the device.
The device is easy to specify:Step 1. Bolt configurationStep 2. Choose the required entry code Step 3. Choose the required exit codeStep 4. Select handing and opening directionStep 5. Select enhancements to customize and suit specific requirements
The code SL304-00-W10 specifies the Slimline 3point with no entry provision and panic bar exit from inside. The enhancement codes specify surface mounting by machine screws (W10).
Note: The code '00' specifies surface mounted and non-handed.
Example system code:
SL 3 0 4 00 W10- -DEVICE BOLTS ENTRY EXIT HANDING ENHANCEMENTS
Number of boltsNumber of bolts Entry Exit Handing
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
No Entry Provision02-point security23-point security
4,5,8 point lockingavailable.
3
Panic Bar4Lever Handle5
Surface Mounted0Mortise Mounted1
Non-handed0Right Hand Reverse4Left Hand Reverse55Right Hand57Left Hand8
Enhancements
Surface mounted bymachine screwsW10
1st Digit
2nd Digit
SLIMLINE: PANIC & EMERGENCY EXIT SYSTEM
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
INWARD OPENING HANDING CODES
OUTWARD OPENING HANDING CODES
LEFT HAND (LH) #8 RIGHT HAND (RH) #7
LEFT HAND REVERSE (LHR) #5 RIGHT HAND REVERSE (RHR) #4
# TO BE REPLACED WITH:
0 FOR SURFACE MOUNTED - 1 FOR MORTISE MOUNTED
Dimensions shown in mmRefer to installation templates for more detail
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
Above performance results are based on independent third party testing or assessment on selected doorsets
High performance multi-point locking mechanism that automatically locks upon door closure to provide high security protection against forced entry, ballistic, and blast in one product.
The flexible design of the product enables external key access with single motion egress at all times by lever handle or panic bar.
The Slimline has been designed with a common mounting footprint enabling the addition of new modules to upgrade to the latest operational requirements.
OPERATIONSEntry - External mechanical key and lever handle are used to release the deadlock function and retract the locking bolts.Upon door closure the bolts will automatically extend and deadlock.
Exit - Single motion egress by either lever handle or panic bar is standard. An alternative method of egress can be provided by key & lever handle operation for non life-safety applications.
FEATURES• Surface mounted or mortise mounted• Storeroom function as standard - automatic locking upon door closure• Classroom function is available - manual locking upon door closure• Proven rack & pinion mechanism• 5/8" stainless steel bolts with 1" throw• Choice of exit device operators• Tested to over 1,000,000 cycles• Suitable for doors 7 feet tall with height extensions available• Up to 5 active locking points• Optional enhancement packs available for blast applications• Optional remote monitoring of lock/bolt status
BENEFITS• Automatic relocking as standard• Life safety device UL305 and BSEN 179/1125 compliant• Tested on specific door assemblies up to 60 minutes of FE/BR and LPS 1175:SR6• Door securely locked when in closed position• Engineered for longevity and trouble free service
Optional ExternalCylinder Protection
SLIMLINE: KEY ACCESS
ENTRY METHODS:
EXITMETHODS:
Manual Key Override
Panic Bar (meets UL305) RTE ButtonCranked Lever (meets EN179)
Access Control with Motorized Lock Remote Access with Motorized Lock
Access Control with Motorized Lock Remote Access with Motorized Lock
1,000,000C Y C L E S
TESTED TO OVERSEISMIC
TESTED
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2008LPCB Cert No. 516-1
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
H28 round tube panic bar.
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
SR4
SR5
SR6
STATE DEPARTMENT
FE/BRSD-STD-01
5MIN
15MIN
60MIN
Blast - For details, contact your sales rep
UL752/EN1522/23 FB1- FB7 & FSG
EN1125/EN179/UL305
UL10C - exceeds 3 hours/BS476 PT22/EN1631-1
Dimensions shown in mm
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
INWARD OPENING HANDING CODES
OUTWARD OPENING HANDING CODES
LEFT HAND (LH) #8 RIGHT HAND (RH) #7
LEFT HAND REVERSE (LHR) #5 RIGHT HAND REVERSE (RHR) #4
# TO BE REPLACED WITH:
0 FOR SURFACE MOUNTED - 1 FOR MORTISE MOUNTED
TECHNICAL DRAWINGS
SLIMLINE: KEY ACCESS - POPULAR ENHANCEMENTS AVAILABLE
M Electric monitoring of bolt status
N Electric monitoring of lock status
Classroom function (manual deadlocking)
U1 Auxiliary bolting unit and continue (above handle)
E(n)
K0
Auxiliary bolting unit (below handle)T
Auxiliary bolting unit and continue (below handle) U
3 Foot top rod extension tube (i.e. E2 or E3)
D02 1” 316 S/S bolt, guides and brackets for high blast levels 3-point
D01 5/8” 316 S/S bolt enhanced blast level cast guides and brackets 3-point
C Slimline aesthetic covers (top and bottom)
CODE
/ DE
SCRI
PTIO
N
SELF-CODING SYSTEMThe Slimline (SL) modular devices have a simple ordering code that covers the chosen methods of entry and exit, followed by additional enhancements to further customize the device.
The device is easy to specify:Step 1. Bolt configurationStep 2. Choose the required entry code Step 3. Choose the required exit codeStep 4. Select handing and opening directionStep 5. Select enhancements to customize and suit specific requirements
The code SL315-04-O5 specifies the Slimline 3 point device external key access with lever handle entry and lever handle emergency exit from inside. The enhancement code specifies Medeco m3-ARXregistered cylinders (O5).
Note: The code “04” specifies a surface mounted and right hand reverse.
Example system code:
SL 3 1 5 04 K2O5- -DEVICE BOLTS ENTRY EXIT HANDING ENHANCEMENTS
Number of boltsNumber of bolts Entry Exit Handing
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
Key and lever entry12-point security23-point security3
Key and lever exit1Panic Bar4Emergency lever5
Enhancements
Cylinder - Medeco m3-ARX (registered)O5
1st Digit
2nd Digit
Surface Mounted0Mortise Mounted1
Non-handed0Right Hand Reverse4Left Hand Reverse55Right Hand57Left Hand8
SLIMLINE: KEY ACCESS
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
1591
.5
289
66
76.5
93.5
46.75
ENTRY METHODS:
EXITMETHODS:
Manual Key Override
Panic Bar (meets UL305) RTE ButtonCranked Lever (meets EN179)
Access Control with Motorized Lock Remote Access with Motorized Lock
Access Control with Motorized Lock Remote Access with Motorized Lock
1,000,000C Y C L E S
TESTED TO OVERSEISMIC
TESTED
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2008LPCB Cert No. 516-1
SLIMLINE: KEY RELEASE LOCKING
Above performance results are based on independent third party testing or assessment on selected doorsets
High performance multi-point locking mechanism that automatically locks upon door closure to provide high security protection against forced entry, ballistic, and blast in one product.
The flexible design of the product provides manual entry after electronic release of an internal deadlock by any access control system. The bolts stay in the locked position until manual operation of the lever handle. Optional external mechanical key override is available to provide secure means of entry during power or system failure. The system provides single motion egress by lever handle or panic bar.
The Slimline has been designed with a common mounting footprint enabling the addition of new modules to upgrade to the latest operational requirements.
OPERATIONSEntry - A signal from the access control system will release the internal deadlock allowing the user to manually retract all locking bolts using the lever handle. Upon door closure the bolts will automatically extend and secure. Exit - Single motion egress by either lever handle or panic bar is standard. Alternate methods of egress can be provided by key & lever handle operation or electronic release of the internal deadlock and manual operation of the lever handle for non life-safety applications.
FEATURES• Surface mounted or mortise mounted• Key override: Storeroom function as standard - automatic locking upon door closure• Key override: Classroom function is available - manual locking upon door closure• Suitable for doors 7 feet tall with height extensions available• Up to 5 active locking points• Optional enhancement packs available for blast applications• Optional remote monitoring of lock/bolt status• 12V DC fail secure, as standard• Optional 24V DC fail secure, 12V DC or 24V DC fail safe
BENEFITS• Integrates with any electronic access control system• Life safety device UL305 and BSEN 179/1125 compliant• Tested on specific door assemblies up to 60 minutes of FE/BR and LPS 1175:SR6• Optional remote monitoring of lock/bolt status• Engineered for longevity and trouble free service
SLIMLINE: ELECTRONIC ACCESS CONTROL
Access control entry(supplied by others)
• Proven rack & pinion mechanism• 5/8" stainless steel bolts with 1" throw• Choice of exit device operators• Tested to over 1,000,000 cycles
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
SR4
SR5
SR6
STATE DEPARTMENT
FE/BRSD-STD-01
5MIN
15MIN
60MIN
Blast - For details, contact your sales rep
UL752/EN1522/23 FB1- FB7 & FSG
EN1125/EN179/UL305
UL10C - exceeds 3 hours/BS476 PT22/EN1631-1
Dimensions shown in mm
161
66
289
91.5
15
76.5
93.5
46.75
SLIMLINE: ELECTRONIC ACCESS CONTROL - POPULAR ENHANCEMENTS AVAILABLE
D02 1” 316 S/S bolt, guides and brackets for high blast levels 3-point
D01 5/8” 316 S/S bolt enhanced blast level cast guides and brackets 3-point
O(n) Cylinder option code – n=0 factory supplied cylinder, other cylinder codes available in catalog
R1 24VDC
Electric monitoring of bolt status
M7 Motorized bolt retraction assembly for Slimline exit system
N Electric monitoring of lock status
B(n) Spacing off of door; (n) = Number of 1mm increments
CODE
/ DE
SCRI
PTIO
N
E(n) 3 Foot top rod extension tube (i.e. E2 or E3)
K0
M
Classroom function (manual deadlocking)
SELF-CODING SYSTEMThe Slimline (SL) modular devices have a simple ordering code that covers the chosen methods of entry and exit, followed by additional enhancements to further customize the device.
The device is easy to specify:Step 1. Bolt configurationStep 2. Choose the required entry code Step 3. Choose the required exit codeStep 4. Select handing and opening directionStep 5. Select enhancements to customize and suit specific requirements
The code SL325-04-K2O5 specifies the Slimline 3 point electronic access control with external manual lever handle entry and lever handle single motion egress. The enhancement codes specify external key release in case of power failure (K2), and Medeco m3-ARX registered cylinder (O5).
Note: The code “04” specifies a surface mounted and right hand reverse system.
Example system code:
SL 3 2 5 04 K2 O5- -DEVICE BOLTS ENTRY EXIT HANDING ENHANCEMENTS
Number of boltsNumber of bolts Entry Exit Handing
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
Access Control22-point security23-point security3
Enhancements1st Digit
2nd Digit
External key release in case of power failure
K2
Cylinder - Medeco m3-ARX (registered)O5
Key and lever exit1Panic Bar4Emergency lever5
Surface Mounted0Mortise Mounted1
Non-handed0Right Hand Reverse4Left Hand Reverse55Right Hand57Left Hand8
TECHNICAL DRAWINGS
SLIMLINE: ELECTRONIC ACCESS CONTROL
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
INWARD OPENING HANDING CODES
OUTWARD OPENING HANDING CODES
LEFT HAND (LH) #8 RIGHT HAND (RH) #7
LEFT HAND REVERSE (LHR) #5 RIGHT HAND REVERSE (RHR) #4
# TO BE REPLACED WITH:
0 FOR SURFACE MOUNTED - 1 FOR MORTISE MOUNTED
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
OPERATIONSENTRY - A signal by the access control system or request to exit switch will release the internal deadlock allowing motorized retraction of all locking bolts. Upon door closure the bolts will automatically extend and secure. For fully automated operation, the locking system should be installed in conjunction with an automatic door operator.An external mechanical key and lever handle can be used to override the access control system and gain entry.
EXIT - A signal by the access control system or request to exit switch will release the internal deadlock allowing motorized retraction of all locking bolts. Single motion egress by either lever handle or panic bar is provided in the event of access control system or power failure.For fully automated operation, the locking system should be installed in conjunction with an automatic door operator.
FEATURES• Surface mounted or mortise mounted• Key override: Storeroom function as standard - automatic locking upon door closure• Key override: Classroom function is available - manual locking upon door closure• Suitable for doors 7 feet tall with height extensions available• Up to 5 active locking points• Optional enhancement packs available for blast applications• Optional remote monitoring of lock/bolt status• 12V DC fail secure, as standard• Optional 24V DC fail secure, 12V DC or 24V DC fail safe• Preprogrammed control box & power supply• Integrate with any Automatic Door Operator
BENEFITS• Remote or local operation capability• Optional remote monitoring of lock and bolt status• Integrates with any access control system and automatic door operator
SLIMLINE: KEY RELEASE LOCKING
Above performance results are based on independent third party testing or assessment on selected doorsets
SLIMLINE: MOTORIZED BOLT RETRACTION
High performance multi-point locking mechanism that automatically locks upon door closure to provide high security protection against forced entry, ballistic, and blast in one product. The flexible design of the Slimline is enhanced with the addition of motorized bolt retraction. When activated with any access control system, the motorized unit will retract all locking bolts. This feature allows local or remote automated opening and closing of the doorset when integrated with an optional automatic door operator. Mechanical override provides single motion egress in the event of access control system or power failure. The Slimline has been designed with a common mounting footprint enabling the addition of new modules to upgrade to the latest operational requirements.
ENTRY METHODS:
EXITMETHODS:
Manual Key Override
Panic Bar (meets UL305) RTE ButtonCranked Lever (meets EN179)
Access Control with Motorized Lock Remote Access with Motorized Lock
Access Control with Motorized Lock Remote Access with Motorized Lock
1,000,000C Y C L E S
TESTED TO OVERSEISMIC
TESTED
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2008LPCB Cert No. 516-1
• Proven rack & pinion mechanism• 5/8" stainless steel bolts with 1" throw• Choice of exit device operators• Tested to over 1,000,000 cycles
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
SR4
SR5
SR6
STATE DEPARTMENT
FE/BRSD-STD-01
5MIN
15MIN
60MIN
Blast - For details, contact your sales rep
UL752/EN1522/23 FB1- FB7 & FSG
EN1125/EN179/UL305
UL10C - exceeds 3 hours/BS476 PT22/EN1631-1
10
Dimensions shown in mm
SLIMLINE: MOTORIZED BOLT RETRACTION - POPULAR ENHANCEMENTS AVAILABLE
146
452
1591
.5
23460
66
76.5
SELF-CODING SYSTEMThe Slimline (SL) modular devices have a simple ordering code that covers the chosen methods of entry and exit, followed by additional enhancements to further customize the device.
The device is easy to specify:Step 1. Bolt configurationStep 2. Choose the required entry code Step 3. Choose the required exit codeStep 4. Select handing and opening directionStep 5. Select enhancements to customize and suit specific requirements
The code SL325-04-K2M7O5 specifies the Slimline 3 point electronic access control motorized bolt retraction with external lever handle entry and lever handle single motion egress. The enhancement codes specify external key release in case of power failure (K2), Motorized bolt release (M7), and Medeco m3-ARX registered cylinder (O5).
Note: The code “04” specifies a surface mounted and right hand reverse system.
Example system code:
SL 3 2 5 04 K2 M7 O5- -DEVICE BOLTS ENTRY EXIT HANDING ENHANCEMENTS
Number of boltsNumber of bolts Entry Exit Handing
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
No Entry Provision0
Access Control
Key and lever entry1
2
2-point security23-point security3
Enhancements1st Digit
2nd Digit
(*must be specified for motorized lock)
External key release incase of power failureK2
Motorized bolt release*M7
Cylinder - Medeco m3-ARX (registered)O5
Key and lever exit1Panic Bar4Emergency lever5
Surface Mounted0Mortise Mounted1
Non-handed0Right Hand Reverse4Left Hand Reverse55Right Hand57Left Hand8
TECHNICAL DRAWINGS
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
INWARD OPENING HANDING CODES
OUTWARD OPENING HANDING CODES
LEFT HAND (LH) #8 RIGHT HAND (RH) #7
LEFT HAND REVERSE (LHR) #5 RIGHT HAND REVERSE (RHR) #4
# TO BE REPLACED WITH:
0 FOR SURFACE MOUNTED - 1 FOR MORTISE MOUNTED
SLIMLINE: MOTORIZED BOLT RETRACTION
D02 1” 316 S/S bolt, guides and brackets for high blast levels 3-point
D01 5/8” 316 S/S bolt enhanced blast level cast guides and brackets 3-point
O(n) Cylinder option code – n=0 factory supplied cylinder, other cylinder codes available in catalog
R1 24 Volt operation
Electric monitoring of bolt status
M7 Motorized bolt retraction assembly for Slimline exit system
N Electric monitoring of lock status
CODE
/ DE
SCRI
PTIO
N
E(n) 3 Foot top rod extension tube (i.e. E2 or E3)
K2
M
External key override in case of power failure
U1 Auxiliary bolting unit and continue (above handle)
Auxiliary bolting unit (below handle)T
Auxiliary bolting unit and continue (below handle) U
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
1,000,000C Y C L E S
TESTED TO OVERSEISMIC
TESTED
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2008LPCB Cert No. 516-1
SLIMLINE: KEY RELEASE LOCKING
Above performance results are based on independent third party testing or assessment on selected doorsets
SLIMLINE: COMBINATION SAFE LOCK ACCESS
Combination lock
High performance multi-point locking mechanism that automatically locks upon door closure to provide high security protection against forced entry, ballistic, and blast in one product.
The flexible design of the product allows the use of a mechanical or electronic combination safe lock to provide lock-down of a Slimline key locking or electronic access control system. After retracting the combination safe lock bolt, the Slimline provides manual entry through its configured means of entry. The system provides single motion egress through a lever handle or panic bar.
The Slimline has been designed with a common mounting footprint enabling the addition of new modules to upgrade to the latest operational requirements.
OPERATIONSEntry - Combination lock is used to lock down the Slimline system. Externally retract the combinationlock bolt and operate the Slimline system as configured with key access or electronic access control then turn the lever handle to retract the locking bolts. Exit - Single motion egress by lever handle or panic bar is standard.
FEATURES• Key override: Storeroom function as standard - automatic locking upon door closure• Key override: Classroom function is available - manual locking upon door closure• Proven rack & pinion mechanism• 5/8" stainless steel bolts with 1" throw• Choice of exit device operators• Tested to over 1,000,000 cycles• Suitable for doors 7 feet tall with height extensions available• Up to 5 active locking points• Optional enhancement packs available for blast applications• Optional remote monitoring of lock/bolt status
BENEFITS• Access control by specified electronic or mechanical combination safe lock• Life safety device UL305 and BSEN 179/1125 compliant• Tested on specific doorsets up to 60 minutes of FE/BR and LPS 1175:SR6• Door securely locked when in closed position• Engineered for longevity and trouble free service
ENTRY METHODS:
EXITMETHODS:
Manual Key Override
Panic Bar (meets UL305) RTE ButtonCranked Lever (meets EN179)
Access Control with Motorized Lock Remote Access with Motorized Lock
Access Control with Motorized Lock Remote Access with Motorized Lock
Combination Safe Lock
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
SR4
SR5
SR6
STATE DEPARTMENT
FE/BRSD-STD-01
5MIN
15MIN
60MIN
Blast - For details, contact your sales rep
UL752/EN1522/23 FB1- FB7 & FSG
EN1125/EN179/UL305
UL10C - exceeds 3 hours/BS476 PT22/EN1631-1
161
222.25
289
91.2
515
66
76.5
Dimensions shown in mm
SLIMLINE: COMBINATION SAFE LOCK ACCESS - POPULAR ENHANCEMENTS AVAILABLE
SELF-CODING SYSTEMThe Slimline (SL) modular devices have a simple ordering code that covers the chosen methods of entry and exit, followed by additional enhancements to further customize the device.
The device is easy to specify:Step 1. Bolt configurationStep 2. Choose the required entry code Step 3. Choose the required exit codeStep 4. Select handing and opening directionStep 5. Select enhancements to customize and suit specific requirements
The code SL335-04-K99 specifies the Slimline 3 point combination safe lock access with external manual lever handle entry and lever handle single motion egress.The enhancement codes specify a combination lock (not supplied) (K99).
Note: The code “04” specifies a surface mounted right hand reverse system.
Example system code:
SL 3 3 5 04 K99- -DEVICE BOLTS ENTRY EXIT HANDING ENHANCEMENTS
Number of boltsNumber of bolts Entry Exit Handing
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
Combination lock32-point security23-point security3
Access Control2Panic Bar4Emergency lever5
Enhancements1st Digit
2nd Digit
Supplied without acombination lockK99
Surface Mounted0
Non-handed0Right Hand Reverse4Left Hand Reverse55Right Hand57Left Hand8
TECHNICAL DRAWINGS
SLIMLINE: COMBINATION SAFE LOCK ACCESS
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
INWARD OPENING HANDING CODES
OUTWARD OPENING HANDING CODES
LEFT HAND (LH) #8 RIGHT HAND (RH) #7
LEFT HAND REVERSE (LHR) #5 RIGHT HAND REVERSE (RHR) #4
# TO BE REPLACED WITH:
0 FOR SURFACE MOUNTED - 1 FOR MORTISE MOUNTED
D02 1” 316 S/S bolt, guides and brackets for high blast levels 3-point
D01 5/8” 316 S/S bolt enhanced blast level cast guides and brackets 3-point
O(n) Cylinder option code – n=0 factory supplied cylinder, other cylinder codes available in catalog
Electric monitoring of bolt status
M7 Motorized bolt retraction assembly for Slimline exit system
N Electric monitoring of lock status
B(n) Spacing off of door; (n) = Number of 1mm increments
CODE
/ DE
SCRI
PTIO
N
E(n) 3 Foot top rod extension tube (i.e. E2 or E3)
K2
M
External key override in case of power failure
K99 No combination safe lock provided
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2008LPCB Cert No. 516-1
ENTRY METHODS:
EXITMETHODS:
Manual Key Override
Panic Bar (meets UL305) RTE ButtonCranked Lever (meets EN179)
Access Control with Motorized Lock Remote Access with Motorized Lock
Access Control with Motorized Lock Remote Access with Motorized Lock
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
SR4
SR5
SR6
Above performance results are based on independent third party testing or assessment on selected doorsets
SLIMLINE: MORTISE MOUNTED SYSTEM
The Surelock McGill Slimline can be mortise mounted inside the cavity of any hollow metal door. This is a discrete mounting method to provide multi-point locking security while concealing the inner workings of the device.
The modular design of the system functions the same as the surface mounted version offering all of the entry/exit, operational and enhancement options.
OPERATIONS: PANIC & EMERGENCY EXIT: Exit - Slimline panic and emergency exit systems are operated using either a lever handle or panic bar to allow single motion egress. Upon door closure the bolts will automatically release and secure the door.
KEY ACCESS: Entry - External mechanical key and lever handle are used to release the deadlock function and retract the locking bolts.Upon door closure the bolts will automatically extend and deadlock.
Exit - Single motion egress by either lever handle or panic bar is standard. An alternative method of egress can be provided by key & lever handle operation for non life-safety applications.
ELECTRONIC ACCESS CONTROLEntry - A signal by the access control system will release the internal deadlock allowing the user to manually retract all locking bolts using the lever handle. Upon door closure the bolts will automatically extend and secure. Exit - Single motion egress by either lever handle or panic bar is standard. Alternate methods of egress can be provided by key & lever handle operation or electronic release of the internal deadlock and manual operation of the lever handle for non life-safety applications.
FEATURES: • Key access/override: Storeroom function as standard - automatic locking upon door closure• Proven rack & pinion mechanism• 5/8" stainless steel bolts with 1" throw • Suitable for doors 7 feet tall with height extensions available• All systems are suitable for in-swing and out-swing doors• The panic and emergency exit system is non-handed • Optional bolt status monitoring is available for the panic and emergency system• Classroom function - manual locking is available for the key access systems• Up to 5 active locking points available• Optional remote monitoring of lock/bolt status can be added to the key release system. • The electronic access control system can come optional remote monitoring of lock/bolt status and 12V DC fail secure as standard• Additional options can be supplied for the electronic access control system- 24V DC fail secure/ 12V DC or 24V DC fail safe
BENEFITS: • Automatic relocking as standard• Life safety device UL305 and BSEN 179/1125 compliant• Tested on specific doorsets up to 60 minutes of FE/BR and LPS 1175:SR6• Door securely locked when in closed position• Engineered for longevity and trouble free service
Blast - For details, contact your sales rep
UL752/EN1522/23 FB1- FB7 & FSG
UL305/EN1125/EN179
UL10C - up to 4 hours/BS476 PT22/EN1631-1 1,000,000C Y C L E S
TESTED TO OVERSEISMIC
TESTED
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
14
SLIMLINE: MORTISE MOUNTED SYSTEM - POPULAR ENHANCEMENTS AVAILABLE
O(n) Cylinder option code – n=0 factory supplied cylinder, other cylinder codes available in catalog
T Auxiliary bolting unit (below handle)
U Auxiliary bolting unit and continue (below handle)
U1 Auxiliary bolting unit and continue (above handle)
N Electric monitoring of lock status
M
K2
Electric monitoring of bolt status
H28 Stainless steel round tube panic bar
K0 Classroom function (manual deadlocking)
External key override in case of power failure
E(n) 3 Foot top rod extension (i.e. E2 or E3)
CODE
/ DE
SCRI
PTIO
N
TECHNICAL DRAWINGS
Number of boltsNumber of bolts Entry Exit Handing
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
No Entry Provision02-point security23-point security3
Key and lever exit1Panic Bar4Key and lever entry1
Access Control2 Emergency lever5
Enhancements
Cylinder - Medeco m3-ARX (registered)O5
The code SL315-14-O5 specifies the Slimline 3 point key access device with lever handle entry and lever handle single motion egress. The enhancement code specifies Medeco m3-ARX registered cylinders (O5).
Note: The code “14” specifies right hand reverse mortise mounted system.
Example system code:
SL 3 1 5 14 O5- -DEVICE BOLTS ENTRY EXIT HANDING ENHANCEMENTS
1st Digit
SELF-CODING SYSTEMThe Slimline (SL) modular devices have a simple ordering code that covers the chosen methods of entry and exit, followed by additional enhancements to further customize the device.
The device is easy to specify:Step 1. Bolt configurationStep 2. Choose the required entry code Step 3. Choose the required exit codeStep 4. Select handing and opening directionStep 5. Select enhancements to customize and suit specific requirements
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
INWARD OPENING HANDING CODES
OUTWARD OPENING HANDING CODES
LEFT HAND (LH) #8 RIGHT HAND (RH) #7
LEFT HAND REVERSE (LHR) #5 RIGHT HAND REVERSE (RHR) #4
# TO BE REPLACED WITH:
0 FOR SURFACE MOUNTED - 1 FOR MORTISE MOUNTED
2nd Digit
Mortise Mounted1
Non-handed0Right Hand Reverse4Left Hand Reverse55Right Hand57Left Hand8
SL314-15-H28T SL305-10 SL315-15-UU1
SLIMLINE: MORTISE MOUNTED SYSTEM
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
The Slimline System supplied with 2mm thick or 3mm thick (motorized version) mounting plate. An optional 5mm thick load plate can be supplied to provide an enhanced mounting method for the Slimline lock and cylinder guard.
INSWING AND OUTSWING STRIKESFOR SURFACE MOUNTED SYSTEMS
MOUNTING/LOAD PLATES
SA
SC2
SFDust Proof Floor Socket
Mounting Plate Load Plate
STRIKES
SC8SB1
SA2 SA1
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
16
For full list of enhancements please see page at the end of this document
THRU BOLT MOUNTING OPTIONS
Retrofitting a security door with a Slimline multi-point lock will elevate the door's physical security. Installing this hardware in the field can be difficult and time consuming on doors and frames originally prepared for other hardware.
Surelock McGill has designed and manufactured a set of heavy-duty 316 grade stainless steel thru-bolt brackets and mounting plates to aid the installer and better protect the property owner against physical attack.
Our thru-bolt mounting solution is 50% faster to install than riv-nuts and offers a higher level of physical security than traditional bolts.
W21 Thru Bolt Mounting arrangement for 1 ¾” thick doors
W22 Thru Bolt Mounting arrangement for 2 ¼” thick doors
HB(n) Hinge bolt option with number of hinge bolts supplied in place of (n)
W20 Thru Bolt Mounting arrangement for custom thickness doors (customer to specify)
CODE / DESCRIPTION
FEATURES• Grade 316 Stainless Steel Construction• Guides and plates for the following mounting locations: - Lock Body - All active locking bolts - Hinge side dog-bolts - Auxiliary Bolting Units - Intermediate Guide Brackets (optional)• Pry -resistant edges resist physical attack• D-shaped barrels on mounting plates prevent rotation while screws are tightened• Options for any door thickness
Internal ExternalIntermediate GuideHinge Bolt
Auxilliary Bolting UnitExit Only Lock BodyExternal Lock Body Plate with Cylinder Guard
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
SL315-04 W21
For full list of enhancements please see page at the end of this document
SLIMLINE: BLAST PROTECTION & ENHANCEMENTS
There are three tiers of blast protection offered by the Slimline. Each level has been tested to at least 100kg of TNT at 15 meters and offer a selection of blast protection enhancements:
Peak pressure values are a guide based on static load calculations on a particular door construction. Calculations should be done for specific door sizes and constructions.
Peak pressure values are a guide based on static load calculations on a particular door construction. Calculations should be done for specific door sizes and constructions.
Enhanced level of Blast Protection:
Basic Level of Blast Protection:
Number of boltsSystem Configuration Load Per BoltkN / LBS
Peak PressureKPa / PSI
3-Point Outward Opening5-Point Outward Opening3-Point Inward Opening5-Point Inward Opening
24.4 / 5485 24.4 / 5485 24.4 / 5485 24.4 / 5485
70 / 10.2 114 / 16.5
42 / 6.1 68 / 9.8
Number of boltsSystem Configuration Load Per BoltkN / LBS
Peak PressureKPa / PSI
3-Point Outward Opening5-Point Outward Opening3-Point Inward Opening5-Point Inward Opening
34 / 7643 34 / 7643 34 / 7643 34 / 7643
102 / 14.8 166 / 24.1
61 / 8.8 99 / 14.4
Peak pressure values are a guide based on static load calculations on a particular door construction. Calculations should be done for specific door sizes and constructions.
High level of Blast Protection:
Number of boltsSystem Configuration Load Per BoltkN / LBS
Peak PressureKPa / PSI
3-Point Outward Opening5-Point Outward Opening3-Point Inward Opening5-Point Inward Opening
236 / 53K 236 / 53K 236 / 53K 236 / 53K
681 / 98.8 1108 / 160.7
408 / 59.2 664 / 96.3
Peak pressure values are a guide based on static load calculations on a particular door construction. Calculations should be done for specific door sizes and constructions.
Extreme level of Blast Protection:
Number of boltsSystem Configuration Load Per BoltkN / LBS
Peak PressureKPa / PSI
3-Point Outward Opening5-Point Outward Opening3-Point Inward Opening5-Point Inward Opening
1000 / 2248001000 / 2248001000 / 2248001000 / 224800
2887 / 4184694 / 680 1732 / 2512817 / 408
Basic Level Enhanced level (D01) High level (D02) Extreme level (D50)
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
3 Point system with enhanced blast hardware
3 Point system no additional enhancements
3 Point system with high level hardware
3 Point system with extreme level hardware
5 Point system with enhanced blast hardware and additional auxiliary bolts that continue above/below handle
5 Point system with additional auxiliary bolts that continue above/below handle - no additional blast enhancements
5 Point system withhigh level hardware, increased bolt size and additional auxiliary bolts that continue above/below handle
5 Point system withextreme level hardware, increased bolt size and additional auxiliary bolts that continue above/below handle
A high-performance, mortise, single point locking system designed specifically for secure applications. The Tyne's thin profile combined with a large bolt makes this product a versatile solution a cross many secure sites and environments.
The system can be unlocked via electronic access control system or via mechanical key. A handle must then be used to retract the bolt.
TYNE LOCK
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
OPERATIONSEntry – Key and lever handle used to release deadlocking system and retract the bolt, allowing the door to be opened. Alternative means of entry can be provided by access control and handle.
Exit – Free egress via lever handle at all times. Alternative egress can be provided by panic bar. Optional thumb-turn or key cylinder deadlock control can be used in the event of a "shelter in place" scenario.
FEATURES• 1.5" X 5/8" 316 Stainless Steel bolt with 1" throw• 12V DC access control solenoid deadlock available with fail-secure feature as standard. Fail-safe
and 24V DC alternative solenoid available• Mechanical access control via rim style cylinder• Self handing and directional• Deadlock status monitoring as standard when specified with access control. Available as an
optional enhancement for key deadlocking systems• Automatic relocking upon door closure• Seamless integration with entire range of Surelock McGill cylinder guards• 316 Grade Stainless Steel Construction
BENEFITS• Straightforward mounting and plug & play wiring for ease of installation• Robust stainless steel construction ensures long life, minimizing replacement and repairs• CE Marked• Suitable for a range of high-traffic environments• Resilient against break-in attempts. Attack tested to LPS 1175 SR3 on selected doorsets• Adjustable restraint to allow for tolerances between the leading edge of door and frame• 5" backset for double-rebate frames• Self handing simplifies ordering and stock levels
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
Above performance results are based on independent third party testing or assessment on selected doorsets
ENTRY METHODS:
EXITMETHODS:
Key & Lever
EN1125/EN179/UL305 in process
Access Control With Lever Handle
Panic Bar (meets UL305) Thumbturn & Lever Key & LeverSS Lever Access Control With Lever Handle
System Option code Voltage Power
consumption per solenoid
Current draw per solenoid
Recommended power supply
Single solenoid
12V – Energise to unlock R (standard) 12V 10W 0.8A 12V 1.5A
24V – Energise to unlock R1 24V 10W 0.4A 24V 1.0A
12V – Energise to lock R2 12V 10W 0.8A 12V 1.5A
24V – Energise to lock R3 24V 10W 0.4A 24V 1.0A
Exit Side Single Action Lever Handle Shown
Entry Side with Key Cylinder and Lever Handle Shown
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
TYNE LOCK
TYNE LOCK - POPULAR ENHANCEMENTS AVAILABLE
SELF-CODING SYSTEMThe Tyne Lock (TY code) device has a simple ordering code that covers the chosen methods of entry and exit, followed by additional enhancements to further customise the device.
The device is easy to specify:Step 1. Bolt configurationStep 2. Choose the required entry code Step 3. Choose the required exit codeStep 4. Select handing and opening directionStep 5. Select enhancements to customise and suit specific requirements
This code specifies a single-point and mortisemounted Tyne Lock with 24V access control &lever handle entry(R1), and single motionegress via lever handle.
Example system code:
TY 1 2DEVICE BOLTS ENTRY
5 10-EXIT HANDING
R1-ENHANCEMENTS
TECHNICAL DRAWINGS
CODE ENHANCEMENT
K0
M Monitoring of bolt and deadlock status - surface cable outlet
Classroom or manual style deadlocking (storeroom function as standard)
R1 Access control (energise to unlock) 24 volt
R2 Access control (energise to lock) 12 volt
R3 Access control (energise to lock) 24 volt
40 [1
.575
in]
25 [0.981 in]
265
[10.
433
in]
205
[8.0
71 in
]
68,5
[2.6
97 in
]
174 [6.85 in]30 [1.181 in]
235
[9.2
52 in
]
21 [0.827 in]3 [0.118 in]16 [0.63 in]
30 [1.181 in]
Number of boltsNumber of bolts Entry Exit Handing
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
No entry0
Key and lever handle1Access Control andlever handle2
1-point securing1 No exit provision0
Key and lever handle1Access Control andlever handle2Thumbturn and leverhandle3
Panic plate4Emergency leverhandle5
Emergency push pad6
Mortise mounted1
Non-handed02nd Digit
EnhancementsExternal key releasein case of powerfailure
K21st Digit
Blast - For details, contact your sales rep
UL752/EN1522/23 FB1- FB7 & FSG
UL305/EN1125/EN179
BS476 PT22/EN1631-1
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
SR4
Above performance results are based on independent third party testing or assessment on selected doorsets
STIRLING - HEAVY DUTY SINGLE POINT LOCK
The Stirling has a common mounting footprint for simple installation. The modular design provides the ability to upgrade the operational and security capabilities in the field.
OPERATIONS: PANIC & EMERGENCY EXIT: Exit - Stirling panic and emergency exit systems are operated using either a lever handle or panic bar to allow single motion egress. Upon door closure the bolt will automatically release and secure the door.
KEY ACCESS: Entry - External mechanical key and lever handle are used to release the deadlock function and retract the locking bolt.Upon door closure the bolt will automatically extend and deadlock.
Exit - Single motion egress by either lever handle or panic bar is standard. An alternative method of egress can be provided by key & lever handle operation for non life-safety applications.
ELECTRONIC ACCESS CONTROL:Entry - A signal by the access control system will release the internal deadlock allowing the user to manually retract the locking bolt using the lever handle. Upon door closure the bolt will automatically extend and secure. Exit - Single motion egress by either lever handle or panic bar is standard. Alternate methods of egress can be provided by key & lever handle operation or electronic release of the internal deadlock and manual operation of the lever handle for non life-safety applications.
MOTORIZED BOLT RETRACTIONEntry – A signal by the access control system or request to exit switch will release the internal deadlock allowing motorized retraction of the locking bolt. Upon door closure the bolt will automatically extend and secure. For fully automated operation, the locking system should be installed in conjunction with an automatic door operator.An external mechanical key and lever handle can be used to override the access control system and gain entry.
Exit - A signal by the access control system or request to exit switch will release the internal deadlock allowing motorized retraction of the locking bolt. Single motion egress by either lever handle or panic bar is provided in the event of access control system or power failure.For fully automated operation, the locking system should be installed in conjunction with an automatic door operator.
FEATURES: • Proven rack and pinion design• Tested to over 1,000,000 cycles• Bolt automatically extends upon door closure• ¾” stainless steel bolt with 1” throwPanic and Emergency Exit • Passage with lever handle optional • Multiple external lockable trim optionsMotorized bolt retraction • Remote or local operation • Easily integrates with automatic door operator for automated opening and closing
BENEFITS: • Engineered for longevity and trouble free service • Tested on specific doorsets up to LPS 1175: SR4 • Life safety device UL305 and BSEN 179/1125 compliant
Key Access • Storeroom function as standard - automatic locking upon door closure • Classroom function is available - manual locking upon door closure • Work with any manufacturer’s rim cylinderElectronic access control • Bolt and deadlocking monitoring as standard • 12V DC fail secure as standard • Optional 24V DC fail secure, 12V or 24V DC fail safe • External key override in the event of power failure
1,000,000C Y C L E S
TESTED TO OVERSEISMIC
TESTED
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2008LPCB Cert No. 516-1
ENTRY METHODS:
EXITMETHODS:
Manual Key Override
Panic Bar (meets UL305) RTE ButtonCranked Lever (meets EN179)
Access Control with Motorized Lock Remote Access with Motorized Lock
Access Control with Motorized Lock Remote Access with Motorized Lock
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
19
STIRLING: POPULAR ENHANCEMENTS AVAILABLE
M Electric monitoring of bolt status
M7 Motorized bolt retraction assembly for Slimline exit system
N Electric monitoring of lock status
O(n) Cylinder option code – n=0 factory supplied cylinder, other cylinder codes available in catalog
K10 External key access no handle required
K2
K0
External key override in case of power failure
H28 Stainless steel round tube panic bar
HS2 Basic Hasp and Staple w/o padlock
Classroom function (manual deadlocking)
H External lever handle for passage function
CODE
/ DE
SCRI
PTIO
N
TECHNICAL DRAWINGS
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
INWARD OPENING HANDING CODES
OUTWARD OPENING HANDING CODES
LEFT HAND (LH) #8 RIGHT HAND (RH) #7
LEFT HAND REVERSE (LHR) #5 RIGHT HAND REVERSE (RHR) #4
# TO BE REPLACED WITH:
0 FOR SURFACE MOUNTED
The code ST124-04-M7W10 specifies the Stirling single point with electronic access control deadlock release with manual lever handle entry and single motion egress with a panic bar. The enhancement codes specify Motorized bolt retraction (M7) and Machine screws for surface mounting on a metal door (W10).
Note: The code “04” specifies surface mounted right hand reverse.
Example system code:
ST 1 2 4 04 M7 W10- -DEVICE BOLTS ENTRY EXIT HANDING ENHANCEMENTS
Number of boltsNumber of bolts Entry Exit Handing
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
No Entry Provision01-point security1 Key and lever exit1Access Control2Panic Bar4
Key and lever entry1Access Control2
Emergency lever5
Enhancements
M7
W101st Digit
2nd Digit
Motorized boltretraction
Surface mountedby machine screws
Surface Mounted0
Non-handed0Right Hand Reverse4Left Hand Reverse55Right Hand57Left Hand8
ST114-05 ST122-05 ST111-05-K13
SELF-CODING SYSTEMThe Stirling (ST) modular devices have a simple ordering code that covers the chosen methods of entry and exit, followed by additional enhancements to further customize the device.
The device is easy to specify:Step 1. Bolt configurationStep 2. Choose the required entry code Step 3. Choose the required exit codeStep 4. Select handing and opening directionStep 5. Select enhancements to customize and suit specific requirements
STIRLING - HEAVY DUTY SINGLE POINT LOCK
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
ORDERING CODE AND SPECIFICATION
SMP CONFIGURATIONS
ADO-SMP Heavy Duty Swing Door Operator
N-DSEL Programmer
ADO-EXTB-Z
ADO-N-DSEL
Operator Arm Extension B
ADO-EXTC-Z Operator Arm Extension C
ADO-AFP200 Retractable Finger Guard
ADO-BSS2FE Articulated Push Arm (Outswing)
ADO-BDT2 Slide Pull Arm (Inswing)
ADO-BDT2R90 Low Profile Slide Pull Arm (Inswing)
ADO-30862
ADO-30864
OPTEX EDGE-T On door safety sensor - Master
OPTEX EDGE-T On door safety sensor - Slave
ADO-RH-E900 OPTEX Edge T Rain Cover
AUTOMATIC DOOR OPERATOR: SMP
The Surelock McGill SMP is a heavy-duty automatic swing door operator. The SMP’s robust, belt driven design can operate doors in excess of 650 pounds making it a perfect fit for substantial blast, forced entry, and ballistic resistant doors.
Using an N-DSEL programming module, the SMP is field programmable to allow for site or even door specific operation. The on-board DC power supply and terminal blocks allow the SMP to seamlessly integrate with any access control, alarm, or lockingsystem.
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
21FEATURES: • Operates doors up to a maximum weight of 650lbs (295kg)• Maximum door width of 55in (1400mm)• Power supply field-selectable 115/230V AC 50-60Hz 5amp circuit (120W)• Working temperature range of 5°F (-15°C) to 120°F (50°C)• 24V DC power supply for external locking accessories• Opening time (95°) is 4-12 seconds/ Closing time (95°) is 5-15 seconds• Optional internal/external safety sensors
BENEFITS: • Motor driven opening and closing provides high degree of site-specific
programming options• Field programmable to customize: o Opening and closing speeds o Hold open time o Force to close (pull in against wind/pressure seals) o Integration with electronic locking devices• Works seamlessly with all Surelock McGill motorized bolt retraction devices• Field programmable push-and-go or push-to-exit
OPENING DIRECTION
Drawings are not to scale.
OPERATOR ON AN OUTWARD OPENING DOOR –BSS2 ARTICULATED PUSH ARM(Extension available to provide additional arm to header clearance)
OPERATOR ON AN INWARD OPENING DOOR –BDT2 SLIDE PULL ARM(Extension available to provide additional arm to header clearance)
OPERATOR ON AN INWARD OPENING DOOR –BDT2R90 SLIDE PULL ARM
OPENING DIRECTION
OPENING DIRECTION
ORDERING CODE AND SPECIFICATION
SLT CONFIGURATIONS
ADO-SLT Medium Duty Swing Door Operator With Closing Spring
N-DSEL Programmer
ADO-EXTB-Z
ADO-N-DSEL
Operator Arm Extension B
ADO-EXTC-Z Operator Arm Extension C
ADO-AFP200 Retractable Finger Guard
ADO-BSS2FE Articulated Push Arm (Outswing)
ADO-BDT2 Slide Pull Arm (Inswing)
ADO-BDT2R90 Low Profile Slide Pull Arm (Inswing)
ADO-30862
ADO-30864
OPTEX EDGE-T On door safety sensor - Master
OPTEX EDGE-T On door safety sensor - Slave
ADO-RH-E900 OPTEX Edge T Rain Cover
AUTOMATIC DOOR OPERATOR: SLT
The Surelock McGill SLT is a medium-duty automaticswing door operator. Its compact installation footprint, ability to operate doors in excess of 450 pounds, and customizable parameters make it an excellent fit for internal security and STC rated doors.
The SLT operator has an internal closing spring that allows for a field programmable low power assisted opening. An N-DSEL programming module allows the SLT to allow for site or even door specific operation. The on-board DC power supply and terminal blocks allow the SLT to seamlessly integrate with any access control, alarm, or locking system.
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
FEATURES: • Operates doors up to a maximum weight of 450lbs (205kg)• Maximum door width of 55in (1400mm)• Power supply field-selectable 115/230V AC 50-60Hz 5amp circuit• Working temperature range of 5°F (-15°C) to 120°F (50°C)• 24V DC power supply for external locking accessories• Opening time (95°) is 4-12 seconds/ Closing time (95°) is 5-15 seconds• Closing spring• Optional internal/external safety sensors
BENEFITS: • Motor driven opening and closing provides high degree of site-specific
programming options• Adjustable closing spring with or without motor assist• Field programmable to customize: o Opening and closing speeds o Hold open time o Force to close (pull in against wind/pressure seals) o Integration with electronic locking devices• Works seamlessly with all Surelock McGill motorized bolt retraction devices• Field programmable push-and-go or low power assisted opening
OPENING DIRECTION
Drawings are not to scale.
OPERATOR ON AN OUTWARD OPENING DOOR –BSS2 ARTICULATED PUSH ARM(Extension available to provide additional arm to header clearance)
OPERATOR ON AN INWARD OPENING DOOR –BDT2 SLIDE PULL ARM(Extension available to provide additional arm to header clearance)
OPERATOR ON AN INWARD OPENING DOOR –BDT2R90 SLIDE PULL ARM
OPENING DIRECTION
OPENING DIRECTION
A-A ( 1 : 2 )
AA
2013
(810)
65
65
15
12
14
99.8 5
850
135.28133.78
43.72
580.95
2 HO
LES FOR
FOR
E-END
FIXING
WITH
8mm
CSK FIXIN
GS
48.0
TOP
439411
25.25
5
43.72
720
51.2
223.5
310
123.2
322
33.5
46.75
71.5
922
40
Technical DetailsTwin Hook Heavy Duty Gate and Door Lock
The Moorgate is designed for securing sliding or hinged gates, doors andhatches. It incorporates two opposing hooks, plus a central horizontal bolt. The system is designed with an internal deadlock to resist prying and gate lift-off attacks. Optional auxiliary hook units can be added above or below the lock body for taller gate/door applications.
The Moorgate is manufactured from 316 grade stainless steel making it suitable for external and hazardous conditions.
The modular design provides flexible solutions to suit many high security gate and door applications.
SR3
Tested to LPS 1175 Security Rating SR3 when fitted on selected gates
OPERATIONSPANIC & EMERGENCY EXIT: Exit - Moorgate panic and emergency exit systems are operated using either a lever handle or panic bar to allow single motion egress. Upon door/gate closure the bolts will automatically release and secure the door/gate.
KEY ACCESS: Entry - External mechanical key and lever handle are used to release the deadlock function and retract the locking bolts.Upon door/gate closure the bolts will automatically extend and deadlock.
Exit - Single motion egress by either lever handle or panic bar is standard An alternative method of egress can be provided by key or thumbturn and lever handle operation for non life-safety applications.
ELECTRONIC ACCESS CONTROLEntry - A signal by the access control system will release the internal deadlock allowing the user to manually retract all locking bolts using the lever handle. Upon door/gate closure the bolts will automatically extend and secure. Exit - Single motion egress by either lever handle or panic bar is standard. Alternate methods of egress can be provided by key or thumbturn and lever handle operation or electronic release of the internal deadlock and manual operation of the lever handle for non life-safety applications. FEATURES• 5/8” horizontal bolt with 1” engagement• 3/8” wide inverted hook bolts with 1-3/4” engagement• Adjustable roller release mechanism for gap variation• Bolts automatically engage upon closureKey access • Storeroom function as standard - automatic locking upon door closure • Classroom function is available - manual locking upon door closure • Work with any manufacturer’s rim cylinderElectronic access control • Bolt and deadlocking monitoring as standard • 12V DC fail secure as standard • Optional 24V DC fail secure, 12V or 24V DC fail safe • Optional bolt and lock status monitoring • External key release in the event of power failure• Auxiliary hook bolt units available for taller gates and doors• Robust strike arrangement• Tested to LPS 1175 Security Rating SR3 on selected gates
BENEFITS• Engineered for longevity and trouble free service
MOORGATE LOCK
Dimensions shown in mm
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
720
134581
4444
25
439
Ø48.0
135850
5100
14
6565
310223.5
51.2123.2
322
46.75
411
2 HO
LES FOR FO
RE-END
FIXING
S WITH
8mm
CSK FIXING
S
40
2020
810
161.06.0
23
Technical Details
The Moorgate has a modular design to meet the required level of physical attack resistance while maintaining its core footprint and operational parameters. Additional active locking bolts can be added to the standard 3-point system to provide added protection for larger doors and gates.
The 5-point “A” design adds vertical rods/bolts that engage into the header and footer while the “B” design adds two additional horizontal hook bolts that engage the frame.
The 7-point version incorporates both the vertical rods and additional horizontal hook bolts to provide maximum protection for taller gates and doors.
Bolt-through cylinder guards are available to meet a higher threat of physical and ballistic attack.
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2008LPCB Cert No. 608
OPTIONAL ENTRY METHODS:
OPTIONAL EXIT METHODS:
Access Control
MOORGATE STRIKES HANDING
Access Control with LeverKey Entry with Lever Access Control with Key Override
Cranked Lever(meets EN179)
Straight Lever(meets EN179) Key Exit with Lever
Thumbturn & Lever
BREAK
Breakdome Thumbturn & Lever
SB1
S-12048-0001/0002
S-12048-0003/0004
SF
5-Point B 7-Point3-Point 5-Point A
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
OUTSIDE (KEYSIDE)
INWARD OPENING HANDING CODES
SWINGING DOORS/GATES
OUTWARD OPENING HANDING CODES
LEFT HAND (LH) #8 RIGHT HAND (RH) #7
LEFT HAND REVERSE (LHR) #5 RIGHT HAND REVERSE (RHR) #4
# TO BE REPLACED WITH:
0 FOR SURFACE MOUNTED - 1 FOR MORTISE MOUNTED
OUTSIDE (KEYSIDE) OUTSIDE (KEYSIDE)
GATE OPENING HANDING CODES (SURFACE)SLIDING DOORS/GATES
LEFT HAND (LHR) 05 RIGHT HAND (RHR) 04
OUTSIDE (KEYSIDE) OUTSIDE (KEYSIDE)
GATE OPENING HANDING CODES (MORTISE)
LEFT HAND (LHR) 15 RIGHT HAND (RHR) 14
MOORGATE LOCK
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
Technical Details
MOORGATE - ENHANCEMENTS AVAILABLE
Electric monitoring of lock status
Cylinder option code – n=0 factory supplied cylinder, other cylinder codes available in catalog
Auxiliary hook unit (below handle)
Auxiliary hook unit (above handle)
Electric monitoring of bolt status
External key override in case of power failure
H28
HS2
K0
K2
M
N
O(n)
T2
T3
Auxiliary hook unit and continue (below handle)U2
Auxiliary hook unit and continue (above handle)U3
Stainless steel round tube panic bar
Basic hasp and staple w/o padlock
Classroom function (manual deadlocking)
H External lever handle for passage function
CODE
/ DE
SCRI
PTIO
N
SELF-CODING SYSTEMThe Moorgate (MG) modular devices have a simple ordering code that covers the chosen methods of entry and exit, followed by additional enhancements to further customize the device.
The device is easy to specify:Step 1. Bolt configurationStep 2. Choose the required entry code Step 3. Choose the required exit codeStep 4. Select handing and opening direction Step 5. Select enhancements to customize and suit specific requirements
The code MG315-05-K2O0 specifies a Moorgate 3-point twin-hook deadlocking system with key access and lever handle to enter and single motion egress with a lever handle to exit. The enhancement codes specify manual deadlocking (K2) and a factory supplied cylinder (O0).
Note: The "05" handing specifies surface mounted left hand opening.
Example system code:
MG 3 1 5 05 K2 O0- -DEVICE BOLTS ENTRY EXIT HANDING ENHANCEMENTSNumber of boltsNumber of bolts Entry Exit Handing
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
Center bolt and 2 hook bolts
No Entry Provision3
Center bolt, 2 hook bolts with top and bottom bolts
5
0Key and lever1Access Control2
No Exit0Key and lever1Access Control withlever
2
Thumbturn and lever3Panic Bar4Emergency exit lever5
Surface Mounted0Mortise Mounted1
0 Non-handed0Right Hand Reverse4Left Hand Reverse55Right Hand57Left Hand8
Enhancements
External key release in case of power failure
K2
Factory suppliedcylinderO0
1st Digit
2nd Digit
MOORGATE LOCK
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
25
Number of boltsProduct RangeFirst 3 digits
Security Rating4th digit
Cylinder Profile5th digit
Mounting6th digit
Mounting Plate7th digit
GSS = Steel cylinder guard for surface mounted locks
GMS = Steel cylinder guard for mortised locks
3 = LPS 1175 SR3
4 = LPS 1175 SR4
5 = LPS 1175 SR5
R = for Rim Cylinders 0 = No mountings supplied
4 = Supplied with 1-1/2" mountings to suit a 1-1/2" to 2" thick doors
5 = Supplied with 2" mountings to suit a 2" to 2-3/8" thick doors
6 = Supplied with 2-3/8" mountings to suit a 2-3/8" to 2-3/4" thick doors
7 = Supplied with 2-3/4" mountings to suit a 2-3/4" to 3" thick doors
0 = Supplied without a mounting plate
1 = Supplied with a mounting plate
Basic Enhanced High
CYLINDER GUARDSExternal key cylinders are the most common method of access control. Enforcing a strict key-control policy may not be enough to keep unauthorized individuals out of your facility. In many instances, a screw driver, crow-bar, or even a hand gun are the only "key" an intruder needs to gain access to a secure location.
Surelock McGill cylinder guards protect against this kind of attack by encasing the key lock in a proprietary alloyof Stainless Steel. The key-way is protected against drilling and ballistic attack by a hardened rotating disc.
FEATURES• Provides up to 60 minutes of resistance against physical attack• Bullet resistant up to 7.62 x 51 armor piercing• Suitable for most rim cylinder designs• Easily integrates with mortise or surface mounted locks• Corrosion resistant
ORDER CODES
UNPROTECTED CYLINDER FAILING PUNCH ATTACK TEST CYLINDER GUARD RESISTING WEDGE/PRY ATTACKCYLINDER GUARD RESISTING DRILL ATTACK CYLINDER GUARD RESISTING GRINDING ATTACK
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
Extreme
Technical Details
Hinge Self-coding System
Number of bolts
STEP 2 STEP 3 STEP 4 STEP 5
100mm x 8mm Satin Stainless
STEP 1
Knuckled HingeHANo pins provided
Knock-in pins
Type Pins/Straps FinishSystem
6
146mm x 10mm7
210mm x 12mm8
A 00Polished stainless01Lacquered brass15Lacquered bronze16Other special99
BScrew in pinsE
Standard HA8 (50mm hinge mounting plate size)
Standard HA6/HA7(40mm hinge mounting plate size)
Mounting plate size
40
50+20 mm mounting plate (leaves) on HA6/HA760+40 mm mounting plate (leaves) on HA6/HA780+50 mm mounting plate (leaves) on HA6/HA790
Example system code: HA7-40-A-00
Features:• Designed to support heavy loading• Robust to withstand a long life of heavy use• Stainless steel hinge pin• Sealed top and bottom knuckles• Bearings within and between each knuckle
Material:• 316 Stainless Steel.
Finish:• Brushed stainless steel (as standard)• 316 Polished stainless steel• Bronze lacquer finish• Brass lacquer finish• Additional finishes available on request
Surelock McGill hinges are designed for heavy duty security, blast and ballistic doorsets.These hinges offer high levels of load carrying capacity. The hinges have been successfully security tested to LPCB SR 2 and 3 on selected doorsets. 316 grade stainless steel hinge pins offer increased levels of protection against physical attack and environmental corrosion.Internal linear bearings combined with thrust bearings between each knuckle, ensure long and trouble-free operation. Our exclusive hinge bolt arrangements are available in a number of options to accommodate all types of doors.
HA6 HA7 HA8
HA6
- 100
mm
(4.0
") s
ecur
ity h
inge
HA7
- 146
mm
(5.7
5") s
ecur
ity h
inge
HA8
- 210
mm
(8.2
5") s
ecur
ity h
inge
NOMINAL HINGE DIMENSIONS (MM)HINGE CODE
A B C D HINGE PIN DIA
SCREW SIZE
HA6 8 19 100 99 9.5 #12
HA7 10 22.2 146 102.2 12.5 #12
HA8 12 32 210 132 19 3/8”
B
D
C
A
SURELOCK SECURITY HINGES
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
27HA6 and HA7 shown with hinge pins
Technical Details
LOADING CHARTThe following chart is a guide for maximum door sizes and weights and a door height of
7 feet using three hinges equally spaced.
HA6-40-E-00Supplied with screw in hinge pins
HA6-40-B-00as HA6-40-A but supplied without hinge pins
Five-knuckle Security HingeFeatures:• Designed to support heavy loading• Robust to withstand a long life of heavy use• Sealed top and bottom knuckles• Bearings within and between each knuckle
maintenance free operation• Additional 3/8" (10mm) mounting hole for
enhanced security• Tested to over 1 million cycles• CE marked BSEN 1935:2002
18.0 (0.709")
8.0 (0.315")
54.0 (2.126")
10.0
(0.3
94")
80.0 (3.150")
HINGE CLOSED VIEW
40.0
(1.5
75")
49.5
(1.9
49")
59.0
(2. 3
23")
8.0 (0.315")
19.0 (0.748")
3.0 (0.118")
7.0 (0.276")
99.0
(3.8
9 7")
100.0 (3.937")
9.0
(0.3
5 4")
14.0
(0.5
51")
21.0
(0.8
27")
9.5 (0.374")
23.0 (0.905")
36.5 (1.437")
50.0 (1.968")
8 HOLES Ø6.4CSK Ø12 x 90°
2 SLOTS R612.5mm x 14mm
1 HOLE Ø10.5CSK Ø20.5 x 90°
2 PINS Ø10 STRAIGHT KNURL
9.0
(0.3
5 4")
22.0
(0.8
66")
2 2.0
(0.8
6 6")
63.5 (2.5")
77.0 (3.03")
90.5 (3.56")
LPS 1175 SECURITY RATING(on selected doorsets)
SR2
SR3
CE certificate of conformity CPR-AC5037
EN 1935:2002 - Class 4 7 7 1 1 4 1 1 4Grade 14
1121 15
0
440
880
1320
1760
2200
2640
3080
3520
3960
44002000
0
200
400
600
800
1000
1200
1400
1600
1800
0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2
DOOR WIDTH IN METRES
DOOR
WEI
GHT
IN K
GS
16 24 31 39 47 55 63 71 79
DOOR WIDTH IN INCHES
DOOR
WEI
GHT
IN P
OUND
SCustom FinishesFinishes available on hinges such as:
Polished Stainless Steel Brass lacquer finish Bronze lacquer finish
HA6 - 40 - A - 01HA6 - 40 - B - 01
HA6 - 40 - A - 15HA6 - 40 - B - 15
HA6 - 40 - A - 16HA6 - 40 - B - 16
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
SURELOCK SECURITY HINGES
STATE DEPARTMENT FE/BR SD-STD-01
5MIN
15MIN
Technical Details
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
SURELOCK SECURITY HINGES
29HA7 - 40 - A - 01HA7 - 40 - B - 01
HA7 - 40 - A - 15HA7 - 40 - B - 15
HA7 - 40 - A - 16HA7 - 40 - B - 16
Custom FinishesFinishes available on hinges such as:
Polished Stainless Steel Brass lacquer finish Bronze lacquer finish
LOADING CHARTThe following chart is a guide for maximum door sizes and weights and a door height of
7 feet using three hinges equally spaced.
HA7-40-E-00 supplied with screw in hinge pins
HA7-40-B-00as HA7-A but supplied without screw in hinge pins
Five-knuckle Security HingeFeatures:• Designed to support heavy loading• Robust to withstand a long life of heavy use• Sealed top and bottom knuckles• Bearings within and between each knuckle
maintenance free operation• Additional 3/8" (10mm) mounting hole for
enhanced security• Tested to over 1 million cycles• CE marked BSEN 1935:2002
LPS 1175 SECURITY RATING(on selected doorsets)
SR2
SR3
CE certificate of conformity CPR-AC5037
EN 1935:2002 - Class 4 7 7 1 1 4 1 1 4Grade 14
1121 15
HINGE CLOSED VIEW
40.0
0 (1
. 575
")
51.1
0 (2
. 012
" )
62.2
0 (2
.44 9
")
5.80 (0.228")
10.00 (0.394")
22.20 (0.874")
2.20 (0.087")
80.00 (3.149")
10.00 (0.394")18.00 (0.709")
52.00 (2.047")
10.0
0 (0
.394
")
2 PINS Ø10 STRAIGHT KNURL
146.00 (5.748")
102.
20 (4
.024
")
8 HOLES Ø6.4CSK Ø12 x 90°
1 HOLE Ø10.5CSK Ø20.5 x 90°
8.50
(0.3
35")
13.3
5 ( 0
.525
")
21.0
0 (0
.827
")
11.11 (0.437")
31.75 (1.250")
52.38 (2.062")
73.00 (2.874")
2 SLOTS R6 12.5mm x 14mm
8.50
(0.3
35")
21.2
0 (0
.835
")
21.2
0 ( 0
.835
")
14.8
5 (0
.585
")
93.62 (3.686")
114.26 (4.498")
134.89 (5.311")
0
200
400
600
800
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
0
440
880
1320
1760
2200
2640
3080
3520
3960
4400
4850
5290
5730
6170
6610
0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2
16 24 31 39 47 55 63 71 79
DOOR WIDTH IN METRES
DOOR WIDTH IN INCHES
DOOR
WEI
GHT
IN K
GS
DOOR
WEI
GHT
IN P
OUND
S
STATE DEPARTMENT FE/BR SD-STD-01
5MIN
15MIN
60MIN
Technical Details
Extended Hinge Mounting Plates
Mounting plates can be extended to required lengths:• 40mm wide mounting plate (Standard)• 60mm wide mounting plate• 80mm wide mounting plate• 90mm wide mounting plate• Please ask us for alternative sizes
Alternative hole pattern arrangements
Custom hinges can be designed with:• Standard hole patterns• Partial hole patterns• Repositioned hole patterns• Blank plates with no hole patterns
Specialist Finishes
Hinges can be provided in a variety of required finishes, with examples including:• Brushed Stainless Steel (Standard)• Lacquered Bronze• Lacquered Brass• Polished Stainless Steel
If you have a specialist hinge requirement for your project, please discuss with our technical sales team for further details including drawing details. Contact details are below.
HA6 & HA7
Based on our proven HA range of security hinges, Surelock McGill are able to design & manufacture custom hinges allowing our solutions to be used with more challenging door constructions. Alternative plate lengths and hole pattern arrangements will enable you to specify Surelock McGill security hinges where the standard design is unsuitable. The hinges displayed on this page are based on existing arrangements; however, please discuss your specific needs with our technical sales team.
59 [2.323 in]
49 [1.949 in]
40 [1.575 in]
HA6 - Standard
79 [3.11 in]
HA6 + 20MM Wide Mounting Plate
69 [2.736 in]
60 [2.362 in]
109 [4.291 in]
HA6 + 50MM Wide Mounting Plate
99 [3.917 in]
90 [3.543 in]
62 [2.449 in]
51 [2.012 in]
40 [1.575 in]
HA7 - Standard
82 [3.236 in]
HA7 + 20MM Wide Mounting Plate
60 [2.362 in]
71 [2.799 in]
112 [4.417 in]
HA7 + 50MM Wide Mounting Plate
90 [3.543 in]
101 [3.98 in]
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
EXTENDED AND CUSTOM SECURITY HINGES
Technical Details
15.00 (0.590")
33.00 (1.299")
27.00 (1.063")
79.00 (3.110")
15.00 (0.590")
33.00 (1.299")
130.00 (5.118")
210.00 (8.268")
81.00 (3.189")
12.00 (0.472")
32.00 (1.259")
8.00 (0.315")
65.00 (2.559")
50.00 (1.969")
8 HO
LES Ø11.00
Five-knuckle Security HingeFeatures:• Designed to support heavy loading• Robust to withstand a long life of heavy use• Sealed top and bottom knuckles• Bearings within and between each knuckle Maintenance free operation
HA8-50-B-00 LOADING CHARTThe following chart is a guide for maximum door sizes and weights and a
door height of 7 feet using three hinges equally spaced.
DOOR
WEI
GHT
IN P
OUND
S (W
ITH
3 HI
NGES
)
0200400600800
1000120014001600180020002200240026002800300032003400360038004000
0200400600800
1000120014001600180020002200240026002800300032003400360038004000
0
880440
132017602200264030803520396044004850529057306170661070507490793083708810
0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2
DOOR WIDTH IN METRES
DOOR
WEI
GHT
IN K
GS (W
ITH
3 HI
NGES
)
16 24 31 39 47 55 63 71 79
DOOR WIDTH IN INCHES
Dimensions shown in mm
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
SURELOCK SECURITY HINGES
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2008LPCB Cert No. 516-1
ENTRY METHODS:
EXITMETHODS:
Hasp & Staple
Straight LeverPush Plate
UL305/EN1125/EN179
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
Above performance results are based on independent third party testing or assessment on selected doorsets
HASP AND STAPLE
The Hasp and Staple is an external, padlock capable devicethat is compatible with many internal lever and panic exitdevices.
When the hasp is secured with a padlock, the uniquedesign offers single motion egress from the inside of thebuilding providing both physical and operational securityfor sensitive areas.
The Hasp and Staple is designed to protect againstmultiple methods and levels of physical and ballistic attack.
OPERATION: Entry - Remove the padlock and lift the hasp and turn. System locking bolts will retract.
Exit - Push panic exit bar/plate or lever. Internal hardware will still operate when the Hasp & Staple isexternally pad locked.
FEATURES: • Compatible with a multitude of padlocks• Manufactured from grade 316 stainless steel• Operates with almost any surface mounted exit device• Non-handed
BENEFITS: • Tested on specific doorsets up to LPS 1175: SR3• Simple operation
ORDER CODES: HS2 - SR2HS3 - SR3
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
5/16” SQUARE SPINDLE
PANIC ESCAPE DEVICE
4 X 5/16” SCREWS
SR2 HASP AND STAPLE
5/16” SQUARE SPINDLE
PANIC ESCAPE DEVICE
4 X 5/16” SCREWS
SR3 HASP AND STAPLE
LPS 1175 SECURITY
RATING(on selected doorsets)
SR2
SR3
SR4
Above performance results are based on independent third party testing or assessment on selected doorsets
BARREL BOLTS
Surelock McGill design and manufacture a selection of heavy dutybolts that serve a wide range of applications. Including modelsthat have been tested and approved to the highest levels of forcedentry and blast protection in the commercial and government markets.
They offer easy installation and provide protection for the inactiveleaf of a double-door or physical security in an area that does notrequire emergency egress or entry.
Number of
Range Strikes & Guides Enhancements
STEP 1 STEP 2 STEP 3
SA.12 Guide bracket/strike & base plate SC.12 Outward opening strike SD.12 Inward opening strikeSF.12 Dust-free floor strike
SA.00 Guide bracket/strike & base plate SC.00 Outward opening strike SD.00 Inward opening strikeSF.00 Dust-free floor strike
TD
TB
SA.12 Guide bracket/strike & base plate SC.12 Outward opening strike SD.12 Inward opening strikeSF.12 Dust-free floor strike
TC
Packing in 1mm increments Bn
Height incrementEn
Number of 1000mmincrementsNPadlock option(padlock not included)F0
Mountingmachine screwW3
SELF-CODING SYSTEMThe Barrel Bolt ancillary product range has a simple ordering code that covers the bolt throw, keeps and additional enhancements to further customise the device.
The device is easy to specify:Step 1. Bolt rangeStep 2. Choose the required strikes and guides Step 3. Select enhancements to customize and suit specific requirements
1488
162236
250 25
62 4210
Ø16
TB - 16mmTD - 12mm
25
40
150
12
6 HOLES Ø 5. 25 THRU
286
15 70 50
TC - 19mm
62
19
32
1488
162236
250
8545
8 HOLES Ø8.5
FEATURES: • .75" DIA 316 Grade stainless steel bolt • Fits most 1/4" shackles• Strike configurations for in and out swing doors• Cast through bolt mounting brackets• Vertical or horizontal mounting• Operating extensions for taller doorsets• Padlock option available for enhanced security
BENEFITS: • Tested on specific doorsets up to LP1175:SR4• Door is secure when bolt is extended into guide bracket• Suitable for use on both timber and steel doorsets • Optional remote monitoring of bolt status available on complete doorsets
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
Bolt Range Bolt Bolt Throw Plate Width (exc. throw)
Plate Length
TD 12 25 150 40
TB 16 25 252 62
TC 19 32 252 62
Nominal Barrel Bolt Dimensions (mm)
Above performance results are based on independent third party testing or assessment on selected doorsets
MEDIUM AND HEAVY DUTY OVERHEAD STOP
The surface mounted stainless steel door stop range hasbeen designed to control the degree of opening with an inbuiltspringing system to absorb shocks when the door is forciblyopened.
With brackets and arms manufactured entirely from Grade 316stainless steel the stops are recommended on doors which are subject to high usage or where external doors open out to hostile weatherconditions such as strong winds.
FEATURES: • Each door stay can be fastened in position to suit degrees of opening ranging from 90° - 110° • The hold open tension can be easily adjusted on site• Manufactured using Grade 316 stainless steel• A variety of arm lengths available to suit varying door leaf width• Diameter of Medium duty 100 series is 12mm and for the Heavy duty is 16mm • Heavy duty 200 series suitable for heavy or wide doors subject to more treacherous conditions• Stainless steel machine screws for reinforced doors and frames are standard. Bolt-through options are available for retrofit
installations on commercial hollow metal doors• Can be installed along our automatic door operators to protect the ADO's arm from damage due to hyper-extension from
forced opening
BENEFITS: • Tested to 1 million cycles • Tested on specific doorsets up to LPS 1175:SR6
PRODUCT CODE ARM LENGTH DESCRIPTION
M140
Medium Duty 100 Series
15 3/4” (400mm) To suit door widths 21 to 27.5” (550mm - 700mm)
M150 19 11/16” (500mm) To suit door widths 27.5 to 35” (701mm - 900mm)
M160 23 5/8” (600mm) To suit door widths 35 to 41” (901mm - 1050mm)
M170 27 9/16” (700mm) To suit door widths 41 to 47” (1051mm - 1200mm)
H240
Heavy Duty 200 Series
15 3/4” (400mm) To suit door widths 21 to 27.5” (550mm - 700mm)
H250 15 3/4” (500mm) To suit door widths 27.5 to 35” (701mm - 900mm)
H260 23 5/8” (600mm) To suit door widths 35 to 41” (901mm - 1050mm)
1,000,000C Y C L E S
TESTED TO OVER
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
ORDER CODES:
OPTION CODES
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
Bx
B – SPACING OF THE LOCKING SYSTEM OFF THE DOORX following the option code is the distance in mm added to the standard offset of the system which is 5mm measured from the door skin to the underside of the bolt. Use the “B” code to increase the amount of engagement of the bolts into the frame. Example: B10 would represent an additional 10mm of space added to the standard system and create 15mm offset from the skin of the door to the underside of the bolt.
D01
D01 – ENHANCED LEVEL GUIDES For increased amount of blast protection that uses a 316 Grade Stainless Steel 5/8” bolt with (4) 5/16” stainless steel mounting screws.
D02
D02 – HIGH LEVEL BOLTS AND GUIDES For increased amount of blast protection that uses 1” stainless steel bolts with (4) ½” mounting screws.
En
E – TOP ROD EXTENSION TUBE For doors taller than 7”. N number proceeding the E code is the number of extension kits added to the standard system. Each kit will include a 3” rod, coupler and clips, and guide bracket and mounting hardware.
HH – EXTERNAL HANDLE For system without mechanical or electronic access control. This code provides a handle and mounting hardware for passage-based Slimline systems which use the “0” for Entry code.
H11
H11 – PANIC BAR EXTENSION For doors wider than 36”. This option code will provide an 1000mm (39-3/8”) aluminum blade, or if option code H28 is selected, an 1100 mm (43-1/3”) round tube bar.
H28
H28 – ROUND TUBE PANIC BARThis option will replace the aluminum extruded bar with a round, 316 grade stainless steel tube on all panic escape systems.
K0
K0 – CLASSROOM FUNCTIONClassroom, or manual locking is a mechanical access control method where the system can be unlocked with a key and then free ingress is allowed until the system is locked again. The standard function of a deadlocking Slimline is storeroom, or automatic locking, which means that the key cannot be removed in the unlocked position.
MM – MONITORING OF BOLT STATUSThis option is available for every version of Slimline and allows the end user to electronically monitor if the bolt is fully extended. 3 - Red
4 - Green
5 - Blue
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
M3
M3 – REQUEST TO EXIT (REX) MODULEThis option is available for adding to either mechanical or electronic locks to provide a dry pulse when egress from the exit side is occurring.
M7
M7 – MOTORIZED BOLT RETRACTIONThis feature is most commonly used in conjunction with an automatic door operator. When the Slimline lock received an external input, such as a push to exit button or a signal from an access control system, all of the bolts will retract and then signal the automatic door operator to open. The bolts will be held back in the retracted position until the door closes at which time the locks will automatically extend and lock the system. The option code includes the center module, motor assembly/terminal block, as well as a power supply unit.
NN – MONITORING OF DEADLOCK STATUSThis option is available for key locking or electronic access control versions of Slimline and allows the end user to electronically monitor if the system’s deadlock is secured.
OPTION CODES
6 - White
7 - Violet
8 - Brown
24V 2ampPSU with
2.5amp timedelay fuse
+ -
Dooractuatoroutput
Accesscontrolinput
1PS
U 24
V2
PSU
0V3
SOL
1 O/
P +
4SO
L 1
O/P
-5
SOL
2 O/
P +
6SO
L 2
O/P
-7
MOT
OR O
/P8
MOT
OR O
/P9
ACT
O/P
+10
ACT
O/P
-11
BOLT
O/P
+12
BOLT
O/P
-13
DLOC
K O/
P14
DLOC
K O/
P15
ILOC
K O/
P +
16IL
OCK
O/P
-17
ACTR
L I/P
+18
ACTR
L I/P
-19
MOT
P I/
P +
20M
OT P
I/P
-21
MOT
U I/
P +
22M
OT U
I/P
-23
BOLT
I/P
+24
BOLT
I/P
-25
DLOC
K I/P
+26
DLOC
K I/P
-27
REST
R I/P
+28
REST
R I/P
-29
EMER
G I/P
30EM
ERG
I/P -
31IL
OCK
I/P +
32IL
OCK
I/P -
33PR
OX 2
4V34
PROX
I/P
35PR
OX O
V36
Basic M7 Motorized Wiring(other features and options available)
Connections to lock 1 - Black 2 - Yellow 3 - Red 4 - Green 5 - Blue 6 - White 7 - Violet 8 - Brown 9 - Orange 10 - Pink 11 -Turquoise 12 - Grey
Connection to access control/alarm system
1 - Black (+ve) Solenoid
2 - Yellow (-ve) 3 - Red
Deadlockstatus
4 - Green 5 - Blue 6 - White
Boltstatus
7 - Violet 8 - Brown 9 - Orange
RTEpulse
10 - Pink 11 -Turquoise Anti-tamper 12 - Grey
Switches shown with lock secure
Power to REX Module 10 V to 28 V DC +ve -ve
(C)
(NO)
(NC)
(C)
(NO)
(C)
(NO)
(NC)
1K
www.surelockmcgill.com - email: [email protected] - phone: 859.899.7870 - Surelock McGill, LLC 2380 Fortune Drive, Suite 120 Lexington, KY 40509
O0
O0 – RIM CYLINDER PROVIDED BY OTHERSKey locking and electronic access control systems will ship with a SFIC round rim cylinder as standard. Choosing this option will remove the cylinder from the packaging and will result in a discounted price.
Rn
Rn – SOLENOID POWER OPTIONSThese options designate on an access control Slimline whether it needs to include Fail Secure or Fail Safe in either 24V or 12V.
TT – AUXILIARY BOTTOM BOLTHorizontal bolt that replaces the standard vertical bottom bolt. Selecting this option will provide clearance above 10” from the finished floor to meet ADA requirements for the full width of the door. This is also a popular option where floor sockets and strikes may interfere with daily operations or collect debris or water.
T1
T1 – AUXILIARY TOP BOLT Horizontal bolt that replaces the standard vertical top bolt.
UU – AUXILIARY BOTTOM BOLT AND CONTINUEHorizontal bolt below lock and then continues to the vertical bottom bolt. This option would be used to add more active locking bolts.
U1
U1 – AUXILIARY TOP BOLT AND CONTINUEHorizontal bolt above lock and then continues to the vertical top bolt. This option would be used to add more active locking bolts.
VV – VISUAL INDICATOR PANEL WITH KEYED RESETThe visual indicator panel, or VIP, is a non-electronic monitoring option that allows visual inspection of an opening. The status flag, reset by a key, will change from green to red if the door has been opened.
WW10 – SURFACE MOUNTING BY MACHINE SCREWS Imperial hardware for all locking components including strikes and bolt guides. If specified, door thickness and spacing off the door will be used to calculate appropriate screw lengths.
OPTION CODES
‘Rn’ OPTIONS24V / 10W / 0.4amp Recommended Power Supply: 24V 1.0amp R1 - Energize to unlock (Fail Secure) R3 - Energize to lock (Fail Safe)12V / 10W / 0.8amp Recommended Power Supply: 12V 1.5amp R0 - Energize to unlock (Fail Secure) R2 - Energize to lock (Fail Safe)
+ Black
- Yellow
SOLENOID POWER CONNCTION
34
Technical Details
MANAGEMENTSYSTEMS
Assessed to ISO 9001:2015LPCB Cert No. 516-1
Technical Details
OFFERING MULTI-THREAT PROTECTION
CYLINDER PROTECTION BLAST BALLISTIC PHYSICAL SECURITY FIRE WIND STORM
Technical Details
Technical Details
Technical Details
OFFERING MULTI-THREAT PROTECTION
CYLINDER PROTECTION BLAST BALLISTIC PHYSICAL SECURITY FIRE WIND STORM
Technical Details