HHoorrssee DDeennttaall EEqquipment - Horse Dental Equipment › upload › ... · Z.I. de Bellevue...
4
Z Z . . I I . . d d e e B B e e l l l l e e v v u u e e R R u u e e B B l l a a i i s s e e P P a a s s c c a a l l 3 3 5 5 2 2 2 2 0 0 C C h h â â t t e e a a u u b b o o u u r r g g F F R R A A N N C C E E 0 0 0 0 3 3 3 3 2 2 9 9 9 9 0 0 0 0 7 7 1 1 2 2 9 9 F F A A X X 0 0 0 0 3 3 3 3 2 2 9 9 9 9 6 6 2 2 3 3 0 0 9 9 1 1 h h o o r r s s e e @ @ h h o o r r s s e e - - d d e e n n t t a a l l - - e e q q u u i i p p m m e e n n t t . . c c o o m m W W E E B B : : w w w w w w . . h h o o r r s s e e - - d d e e n n t t a a l l - - e e q q u u i i p p m m e e n n t t . . c c o o m m H H o o r r s s e e D D e e n n t t a a l l E E q q u u i i p p m m e e n n t t
Transcript of HHoorrssee DDeennttaall EEqquipment - Horse Dental Equipment › upload › ... · Z.I. de Bellevue...
ZZ..II.. ddee BBeelllleevvuuee RRuuee BBllaaiissee PPaassccaall
3355222200 CChhââtteeaauubboouurrgg
FFRRAANNCCEE �������� 00003333 22 9999 0000 7711 2299 FFAAXX 0000 3333 22 9999 6622 3300 9911
�������� hhoorrssee@@hhoorrssee--ddeennttaall--eeqquuiippmmeenntt..ccoomm WWEEBB:: wwwwww..hhoorrssee--ddeennttaall--eeqquuiippmmeenntt..ccoomm
HHoorrssee DDeennttaall EEqquuiippmmeenntt
To clean the handpieces, run them in clean water for a few seconds at high
speed.
Dry them with a towel.
Use only a stainless brush to clean the
diamond head.
Position the hand pieces upright
( head downwards ) to keep water out of the
bearings.
Maintenance HHDDEE BBaassiicc UUnnii tt
Humidify the drills before using
Do not forget to rinse the horse’s mouth after the operation
Do not use the drills with an engine of more than 3000 rpm ( max. Speed 2 to 3 )
Precautions before using the drills :
PPrreeppaarraatt iioonn AAnnggllee HHaanndd PPiieeccee oorr FF33
Achieve a bit -seat on the 306 & 406 without any difficulties.
This hand piece is to be used without extension.
Use this hand piece to work on canines & incisors a s well.
Screw the drive shaft to the engine.
Verify that the transmission screw of the drive shaft fits well
in the engine’s slit.
Thread the drive shaft in the extension.
Pull the black ring on the drive shaft head
back and push into the drill.
Then push the black ring back into place.
With a Quickflex head, it is enough to insert the drill in the head of drive
shaft.
MMaaxxii ll llaarryy HHaanndd PPiieeccee oorr FF11 MMaannddiibbuull llaarryy HHaanndd PPiieeccee oorr FF22
The 2 protective pa nes guide the hand piece along the tooth (see arrow).
To work on the 11s, use the flat end of the guard t o push the soft tissue and grind only the tooth.
Warning : Keep the handpiece moving along the arcade; do not rest the burr on one tooth as we encourage you not to take off too much tooth.
To work on the 11s, use the top of the head (much
finer) and use the cylindrical to finish the
work.
To do a bit -seat, work from the opposite side of the mouth (for example use
handpiece in left hand to work on 206).
Use your thumb to guide the hand piece (see enclosed
picture).
