Hg Combi Cut Touch 11.09.2011 Eng
-
Upload
thanasis-tsoutsoulianis -
Category
Documents
-
view
225 -
download
0
Transcript of Hg Combi Cut Touch 11.09.2011 Eng
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
1/80
11. september 2011
USERS MANUAL
HG COMBI CUTWith touch
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
2/80
Telephone 0045 75891244
- for professionel farmes 2
We thank you for bying the new HG Combi Cut.
Hedensted Gruppen A/S always tries to produce quality products, which
you can count on. We are sure that you will be pleased with your new
machine. To make sure that you get the most advantages from the
machine from the start, it is important to study the functions very carefully.
The users manual contains, all the technical details and diagrams, an
examination of the basis adjustments, a schedule with trouble shooting
and mending of these, and a new section called often asked questions
or FAQ.
There are also small sections of spare parts with item numbers, which can
be very useful.
There are pictures at the back of the manual of the machine and its parts.
If you need service, it can be a great help both to you and our service
team that we jointly according to the pictures can trace, where the
problems are at the machine.
Therefore it is important that you always know, where the users manual is.
We suggest that you keep it in the electric cupboard at the back of the
machine.
From the factory the machine is rough adjusted, but because of the
difference in mink, it is not sure that it fits 100 % to your mink.
An employee from Hedensted Gruppen will make the fine adjustment.
Before you get a visit for a start up, we will ask you, and the operator to
read the user's manual thorough, and to make sure, that the persons, who
are going to work with the machine are present during the visit.
You also must make sure, that there are supplies of air and power 380V,
and that it is lead to the machine.
Hedensted Gruppen A/S wishes you great pleasure with your new HG
Combicut.
Kindly regards
HEDENSTED GRUPPEN A/S
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
3/80
Telephone 0045 75891244
- for professionel farmes 3
1. Table of contents.
1. Table of contents. .................................................................................. 3
2. Machine information............................................................................... 4
3. Introduction. ........................................................................................... 5
3.1 Construction. ................................................................................. 5
3.2 Warranty........................................................................................ 5
4. Warning.................................................................................................. 6
4.1 Hazed signs................................................................................... 7
5. Setup of the Combi Cut.......................................................................... 8
5.1 Connection .................................................................................... 8
5.2 Connection of extra equipment...................................................... 9
5.3 Relocation. .................................................................................... 9
6. Control platform. .................................................................................. 10
7. Operation of the Mac panel.................................................................. 12
8. Description of screen pictures.............................................................. 13
9. Operating the HG Combi Cut.............................................................. 22
10. Adjustment ......................................................................................... 25
10.1 Change between male and female............................................ 26
11. Maintenance/Cleaning ....................................................................... 27
11.1 Daily cleaning and maintenance................................................ 27
11.2 Weekly cleaning and maintenance............................................ 28
11.3 Storing of the HG Combi Cut..................................................... 28
12. Spare parts. ....................................................................................... 29
13. FAQ.................................................................................................... 45
14. Air diagram......................................................................................... 49
15. Electric diagram. ................................................................................ 53
16. EC Declaration of Conformity............................................................. 54
17. Technical specifications..................................................................... 55
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
4/80
Telephone 0045 75891244
- for professionel farmes 4
2. Machine information.
HG Combi Cut TYPE:.
MACHINE NO.: YEAR:..
CUSTOMER:
DEALER:
..
...
.
Id plate:
3+400+N+PE
2,9 7
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
5/80
Telephone 0045 75891244
- for professionel farmes 5
3. Introduction.
HG Combi Cut is used for cutting up mink.
The slicing machine is constructed to carry out a correct cutting of the
male/female mink combined with loosen the behind legs in one working
operation.
The capacity of the machine with the leg loosener are up to about 180
pieces of mink pr. hour, and without the leg loosener up to about 350
pieces pr. hour (Both values are with trained users).
At the same time the machine has a flexible working area, which ensures
a correct slicing of mink of variable sizes.
3.1 Construction.
HG Combi Cut is constructed in surface treated steel with painted shield.
All the components are of the highest quality, and this combined with a
well-arranged operation indicates, that this is a machine of high quality
Vertical and horizontal movements run on precision ball shears, which
ensures a good repeatability.
3.2 Warranty.
There is 1 year of warranty on the HG Combi Cut.
Defect parts can be replaced, if the defect can be assigned to a
fabrications error. Errors, which can be assigned to freight is not included
in this warranty.
In cases of irresponsible treatment of the HG Combi Cut, no warranty is
given, either on the machine or on damaged skins.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
6/80
Telephone 0045 75891244
- for professionel farmes 6
4. Warning.
Read this users manual thoroughly before using the machine.
Avoid staying too close to the machine, when you connect air and
electricity, because the moveable parts can react quickly.
The operator must have instructions in use of the machine.
The slicing must only be used for slicing of mink.
Wrong use or ignorance of the security instructions can cause damages
on the body or breakdown of the machinery.
Pay attention in following sectors:
1. Look out the machine contains rotating knives. (1)
2. Emergency stop must not be covered or put out of function. (2)
3. The slicing machine contains vertical and horizontal moveable
knives. (3)
4. Look out the slicing machine contains vertical moveable parts.(4)
5. There is a risk of jamming your fingers in the paw holder. (5)
6. By use of the machine you have to use eye protectors.
2
4
1
3
3
5
5
1
2
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
7/80
Telephone 0045 75891244
- for professionel farmes 7
4.1 Hazed signs.
DANGER HIGH VOLTAGE
The operating box of the machine contains high
voltage. Because of the danger, the box must not
be opened by unauthorized employees.
DANGER ROTATING PARTS.
Avoid touching the moveable parts of the machine
with fingers or clothing, this can cause damages
on the body.
DANGER SHARP KNIVES.
The machine contains more sharp knives, both
rotating pneumatic moveable. Avoid touching with
fingers and clothing, this can cause damage of the
body.
EAR- AND EYE-DEFENDERS DEMANDED.
During operation of the machine glasses must beused, because hair, sawdust and other objects
can be thrown out.
During operation ear defenders must be used,
because the sound level of the machine exceeds
the normally allowed.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
8/80
Telephone 0045 75891244
- for professionel farmes 8
5. Setup of the Combi Cut.
The HG slicing machine has to be placed on a solid and plane floor, so
that the machine can be operated standing or sitting on a special chair.
The height of the room must minimum be 3,00 cm.
The legs of the machine have to be adjusted, so that it stands in level and
is steady without tipping. After setup you can remove the transport
brackets on the legs of the machine by help of the 4 bolts, if they annoy
the user.
Notice that the weight of the machine is 300 kg.
Attention : Keep the transport fittings, if the machine has to removed.
5.1 Connection
Electricity:
The HG Combi Cut is fit with a 16A CEE-socket to which 400 volt is
connected with zero and earth. The machine has a maximum power
consumption on 2,9Amp during running.
Air:
The slicing machine demands a
compressor pressure on min. 7 bar,
and an air supply on min. 500 l/min.
The air is connected with an air
coupling of the Cejn 320.
To avoid stop in the slicing, it is
important that the air, which is used
in the slicing machine is free of
water and dirt, as well as rust from
old pipes.
Warning: The moveable parts will react quickly by connection of air.
Air tube and electric cable must not lay loose on the floor, because of risk
of personal damage.
AIR IN 3x400V
OUT 3x400V
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
9/80
Telephone 0045 75891244
- for professionel farmes 9
5.2 Connection of extra equipment.
The HG Combi Cut is fit with a 16A CEE socket with 3x400V. The socket
is switched on and off on the main switch on the operation panel of the
slicing machine. Extra equipment, such as HG Grid conveyor or HG
Transport belt, which has to run at the same time as the slicing machine,
can with advantage be connected to the socket.
5.3 Relocation.
Before moving the machine you have to disconnect the air- and electricity
connection. Pay attention, the moveable parts of the machine can change
position, when the machine vents.
Mount the transport brackets on the legs of the machine, and move it with
a palletizer. Pay attention that the cables and the tubes of the machine are
not squeezed.
Warning:
Do not lift the machine in the moveable tower.
Notice that the weight of the machine is 300 kg.
By setup on a new location repeat the procedure, which is described
under section 5.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
10/80
Telephone 0045 75891244
- for professionel farmes 10
6. Control platform.
1. Emergency stop.
2. Reset.
3. Reverse use by wrong inserted animal at the behind leg
loosener procedure. By activating and simultaneous press on the
foot pedal you can reverse in this sequence.
4. Stop possibility for stopping between every sequence.
5. Lamp blinks before hooks to the hind leg loosener closes
6. Mac panel. (See the section about programme)
7. Knee pedal with start & emergency stop.
1.Step = start, 2.step = emergency stop
8. Reset emergency stop in foto pedal.
7
6
1
2 3 4 5
8
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
11/80
Telephone 0045 75891244
- for professionel farmes 11
1. Tower with tail roll, tail slicing and spade for belly.
Spade for back and tail, and pull off hooks for hind legs.
2. Cross knife.
3. Left paw holder/clip/cut system.
4. Right paw holder/clip/cut system.
5. Operation panel (MAC Panel).
6. Adjustment of stretch pressure.
7. Main switch.
8. Body holder.
9. Knee pedal.
10. Valve system.
11. Air pressure
9
1
11
2
4
5
6
7
3
8
10
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
12/80
Telephone 0045 75891244
- for professionel farmes 12
7. Operation of the Mac panel.
At the operation panel on the skinning machine there is a touch panel. The
panel is used to adjust the machine to the user and his mink, but it can
also inform the operator with different statistical information.
You operate the panel by pressing the display, on the area illustrated with
the wanted menu. If you want to change a value, press on value and the
below numeric keyboard emerge. Here you key the wanted value followed
by enter.
The other keys on the keyboard have following functions:.
Display shows the keyed value
Esc Return to screen menu without
saving the keyed value
Deletes the character to the left for
the cursor
Clr Deletes the total keyed value.
Del Deletes the character to the right
for the cursor.
Enter Saves the keyed value and
returns to screen menu.
Moves the cursor one step to the
Moves the cursor one step to the left.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
13/80
Telephone 0045 75891244
- for professionel farmes 13
8. Description of screen pictures.
When you start up the below screen picture emerge. Reset the emergency
stop circuit to activate the machine's operating system.
If the message at the top of the panel appears, deactivate emergency
stop devices on the dashboard and pedal.
Now press the reset emergency stop circuit and the main menu appears.
.
When this message is displayed, the emergency stop is activated and prevents the
operator to reset the emergency stop circuit .
Reset the emergency stop on the panel by turning the knob clockwise.The device in knee pedal reset by pressing the blue button.
Button to reset the machines emergency
stop circuit.
Back to main menu
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
14/80
Telephone 0045 75891244
- for professionel farmes 14
This picture is the machine's main menu and by pressing "Return" key in
the other screens it will returned to this.
In the middle of the screen displays the operator messages. The machine
writes which program is active and alarms if it is missing a signal.
Main menu
Buttons to open screens whose name is
affixed to the key.
On screens that are described in the
following, are also equivalent keys. But
the key text varies depending on which
keys are active.
Counter for daily production. Can be
edited by pressing on the value. The cycle time shows number of
seconds for the last used cycle.
Counter for the total production of the
machine. Cannot be changed.
Switch between male and female
program. In the following screens are
individual setup options for these 2
programs
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
15/80
Telephone 0045 75891244
- for professionel farmes 15
Vertical menu.
Button for other settings on the vertical
axis.
Setting the position where the
skinloosen sequence is completed,
and it releases the animal. This way
the machine does not have to drive all
the way to the top if it is not necessary.
When the tower has reached the
position, it releases the animal, and
the next cycle may begin. The
distance is calculated from tower top
and down.
Setting the depth of the triangle cut in
Male and Female program
Setting the depth, the leghooks run,
before it closes for Male and Female
program.
Setting the pause between the spade
reaches its bottom position (Spade
down) and the Tailroller closes.
Setting the tower's starting position in
Male and Female program. The
distance calculated from the tower's
top position.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
16/80
Telephone 0045 75891244
- for professionel farmes 16
Vertical settings menu.
You can disconnect the foot pedal to
the tail spade and the tail hook. After
the leghooks is closed, the machine
will finish without further steps.
Step tailhook is only active when
vertical step is set to OFF. Here you
can select if the operator wants a step
between the tailhook close and the
tower going up.The feature can protect against pelting
error at the tailhook when running
without vertical steps.
Adjust the speed the belly spade runs
down with.
Set as a % of max speed.
Adjust the speed the leg hooks run
down with.
Set as a % of max speed
You can switch off the hind leg
loosener module. Now the machine
will run as an ordinary slicing machine.
Adjust the speed the tower runs up
with, when you loosen the skin on the
legs and the tail. Set as a % of max
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
17/80
Telephone 0045 75891244
- for professionel farmes 17
Horisontal menu.
If the crosscut knife runs left and will not continue, the margin between the
stretch position and crosscut position are too large. Reset the machine
and set stretch time up a bit.
Setting stretch length before the knife
starts to run.
When using a low-pressure stretch, a
high value must be entered so the
knife begin to position later.
Please note that the value does not
exceed the animal's size. In this case,
the knife remain in the starting position
and wait.
Adjustment of extra stretch time.
Increasing this value makes it easier
for the machine to find the correct
cross cut position. At 0.1 sec the
machine runs as fast as possible, and
are default settings. If the stretch
pressure is very low, it may be
necessary to increase this time, so
that the operator gets more time to put
the animal correctly in before the knife
reads its cutting position.
Setting the cross cut speed.
Speed entered in % of max speed.
Setting the number of paw cut.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
18/80
Telephone 0045 75891244
- for professionel farmes 18
Setting knife positions menu.
Buttons to stretch paw holders in and out, so the operator can drive the blade manually
to its positions.
With knife down, the knife function up / down can be manually activated.
Buttons to run cross the knife to his
position in right, center or left side.
Correction of the crosscut start and
stop positions. Correction in the right
and left sides, enter a higher value to
get further out towards the feet.
The knife center are positive numbers
further to the right side.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
19/80
Telephone 0045 75891244
- for professionel farmes 19
Vertical setting menu.
Adjust the machine to run with paw clip (OF) or paw cut (ON).
When paw on function is used, paw blow cannot be turned ON.
Blow of paws can here switched on and off. Blow can only be turned ON, when
running with option Paw OFF.
Here you can turn on and off, the stop of the cross knife. At stop, the knife only
drives on by activating the foot pedal. If you keep down the foot pedal after start
the knife runs without stopping.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
20/80
Telephone 0045 75891244
- for professionel farmes 20
Technic menu.
Version Date of software saved in the
machine.
Load the machines factory settings.
Button to reset the machines emergency
stop circuit.
Under the menu I/O tests can machines
different signals be seen. All inputs and
outputs from the PLC is listed.
If the square field "in/output" is dark it is
active.
Under the menu manually, the functions
can be activated manually.
Danish or English texts in the panel.
Key 0 for Danish and 1 for English.
Grinding function. Press this button to
activate the knifes on and off manually.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
21/80
Telephone 0045 75891244
- for professionel farmes 21
8. Starting up the HG Combi Cut
The below procedure is made without mink.
1. Connect Electricity 3x400V+0+PE
2. Connect air Min. 7 bar.
Warning: The moveable parts will react quickly an run to starting
position.
3. Check input pressure (7 bar)
4. Adjust the input pressure (7 bar)
5. Emergency stop on panel and pedal must be deactivated.
6. Press the button Reset Emergency stop on the touch panel.
7. Press the button Reset.
8. Press the foot pedal.
Warning: Now the machine will run a cycle.
9. Watch the stretch pressure (min. 1 bar - max. 4 bar)
10.After running a cycle the machine returns to starting position.
10.1 You can adjust the stretch pressure
10.2 Adjust other things in program
11. Repeat this procedure point. 7 to 9, until the machine has the
wanted pressure.
Warning: Only adjust the machine when it does not run, or you risk
to get squeezed between the moveable parts of the
machine.
When you adjust the machine, do not activate the knee
pedal.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
22/80
Telephone 0045 75891244
- for professionel farmes 22
9. Operating the HG Combi Cut.
The slicing machine can be adjusted so that it fits to the need of the
operator. The below description of the operation take basis in the factory
adjustments, where the machine runs with hind leg loosener and step
functions.
If the machine is adjusted to work as a ordinary slicing machine without
hind leg loosener then skip point 10 15.
1
9
3
6
10
5
4
7
9
2
1
8
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
23/80
Telephone 0045 75891244
- for professionel farmes 23
1 Take the rear paws of the mink between forefinger and thumb, so
that the belly points against the machine.
2 Place the paws in the paw holders (1)
NOTICE! Do not place the paws too deep in the paw holders, this
can cause that the slicing do not get optimal.
Warning: Avoid putting your fingers between the paw holders.
3 Lock the paw holders by activating the foot pedal.
4 Then the machine pulls the paws from each other, and at the same
time the knife (2) runs against left.
5 Before you start to slice:
a) Fetch the tail of the mink with the right hand.
b) Turn the hand so that it is placed right under the tail root and
the skin.c) Decide the cut by pulling or pushing the body.
6 The 50 knife (2) to the long running cut now cuts from left against
right. When the knife reaches the right hind leg, the knife returns to
starting point.
7 The spade (4) runs down and loosens the skin on the belly.
8 The 80 knives (5) cut the V-cut by a down going movement.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
24/80
Telephone 0045 75891244
- for professionel farmes 24
9 Under the V-cut you lift the tail point to vertical position and you put
the tail into the tail roll (3), and this will pull the tail against the nylon
roll and cut the tail, while the spade runs up with a vertical
movement. Now the tail is cut up. The spade returns to starting
point.
10 The hind leg hooks runs out with a horizontal movement.
11 Step foot pedal. The tail is pulled, so that the cross cut opens up.
You steer with the tail of the mink, so that the back hook is about
75 % free of the hind leg. Step pedal. Then the hook runs down
with a vertical movement and stops with an open hook. Activated
the foot pedal. Next step closes the hook around the thighbone.
12 Activate the foot pedal. Then the tail loosener spade (7) runs with a
horizontal movement. Pull hard in the tail, and the spade runs down
on the back of the mink.
Activate the foot pedal. Back hook closes.
13 Activate foot pedal. Body holder (8) is activated around the mink
and is kept.
14 Paws are clipped (9) or cut release the mink. (Section 13.3)
15 The tower (10) runs up vertical, at the same time hind leg and tailare loosened.
16 Body holder returns to starting position, and the mink dumps down
on the conveyor belt.
17 The operator takes a new mink, and the machine returns to starting
position.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
25/80
Telephone 0045 75891244
- for professionel farmes 25
10. Adjustment
To obtain the optimal slicing it is necessary to adjust the machine
individual to each operator.
1. Adjustment of the thigh supporter (1), so that the give a good
support.
2. Adjust the paw clamp (2), so that the paw is properly tightened
during the slicing.
3. Adjust the paw knife (3), so
that it cuts or clips paw.
4. Adjustment of the hind leg
hooks (4). These have to be
adjusted in the MAC panel,
so that they run 3 mm past
the thigh supporter
immediate after the hooks
close. If they run too far you
risk to spoil the hind leg skin.
5. Adjust the tail roll (5), so
that the centre of the two
80 mm knives are right
outside the upper edge of
the tail roll.
6. Adjustment of the hooks
to the hind leg loosener
(6), it has to go down a
1/3 into the backside of
the cut up hind legs.
6 54
213
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
26/80
Telephone 0045 75891244
- for professionel farmes 26
10.1 Change between male and female.
In the Mac panel you distinguish, as earlier mentioned, between male and
female values for the position of the tower. The Male/Female reverser on
the operation panel changes between these typed values.
To obtain the optimal slicing you also have to change between the wedges
on the belly spade. The wedge positioned the mink correctly in proportion
to the triangular cut.
By slicing of MALE mink wedge 1 has to be mounted alone.
By slicing of FEMALE mink the wedges 1 and 2 have to be mounted.
The hind leg hooks (3) have to be adjusted, so that the hooks close
around between the skin and the thigh on the mink.
The opening on the hind leg hooks have to be adjusted to about 32 mm forMALE mink.
For FEMALE mink the opening has to be adjusted to about 16 mm.
The stretch pressure on the paw stretch also has to be changed between
MALE and FEMALE.
By Male mink the stretch pressure is adjusted to about 3 bar.
By FEMALE mink the stretch pressure is adjusted to about 2 bar.
1
2
3
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
27/80
Telephone 0045 75891244
- for professionel farmes 27
11. Maintenance/Cleaning
To make the slicing machine work optimal, you have to clean and maintain
it after following description.
11.1 Daily cleaning and maintenance
Before you start cleaning, disconnect electricity and pneumatic air.
1 After use only clean the machine with pneumatic air.
2 Remove slicing rests and sawdust from the moveable parts of the
machine, so they can run freely and easily.
3 Empty the water separator (1).
4 Check the air filters(1+3). Replace as needed.
2 13
Cleaning: Only use pneumatic
air in the area of the circle.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
28/80
Telephone 0045 75891244
- for professionel farmes 28
11.2 Weekly cleaning and maintenance
Before cleaning the machine disconnect electricity and pneumatic air.
1. After use clean the machine with pneumatic air.
2. Empty water separator (1).
3. Check the oil level in the pneumatic lubricator and replenish after
need (2).
Always use the right air oil: Statoil NUTO H 15.
Hedensted Gruppen item no. 476550
4. Shears and slippery surfaces are dried clean and oiled with fine oil.
Hedensted Gruppen item no.476590
5. The lubricating nipples of the shears are oiled with grease.
Hedensted Gruppen Item no. 476570 (Patron 400g)
11.3 Storing of the HG Combi Cut.
To obtain a long lifetime and good reliability by starting up, it is necessary
to clean the machine well and make an extra oiling. The slicing machine is
cleaned as described under daily/weekly cleaning.
Shears and slippery surfaces are dried and oiled with fine oil
Hedensted Gruppen item no. 476590
The lubricating nipples of the shears are oiled with grease.
Hedensted Gruppen item no. 476570 (Patron 400g)
Oil the air engines extra well by opening the pneumatic lubricator and run
a couple of times with the machine.
Remember: To close completely for the pneumacit lubricator again, and
then open 1 round then it is ready for next season.
Always use the right air oil: Statoil NUTO H 15.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
29/80
A
1
:
1
,
5
)
PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangivettoleranceriht./Notspecificedtoleranceaccordingto:
Material:
Scale:
Overfl.beskaffenhed/Surfaceproperties:
Konst./Designed:
Tegnet/Drafted:
Date:
Description:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsave
d:
Sheetsize:
DS/ISO2768-m
Sheet
/
Thisdocumentisstrictlyconfidentialandmustonnoaccountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
2
KL
KC
12-05-2004
Assemblytower2010
A3
31-05-2010
1
207943
KC
Allekanterreifes
Breakealledges
PartsList
DESCR
IPTION
PAR
TNUMBER
QTY
ITEM
Boltunbrakocyl5x20
FZB
1020
5020
4
1
Boltunbrakocyl5x25
FZB
1020
5025
4
2
Boltunbrakocyl6x10
FZB
1020
6010
2
3
Boltunbracocyl6x20
FZB
1020
6020
3
4
FittingboltM8-10x20mm
2020
8020
1
5
Frameforspadelift2010
2079
45
1
6
Assemblyleghookandtailrollsystem2010
2079
54
1
7
LocknutMP150189_M10x1,25
2104
27
1
8
CylinderRT57225/M/50
2116
16
1
9
UF-JointQM-8025-32
2141
16
1
10
L-JointQM-57025-24
2141
40
1
11
Reedsensoryellow
2143
12
2
12
Socketwith3Mwire
2143
14
2
13
Clampforsensor
2143
16
2
14
Banjoflowcontrol6
1/8"
2151
10
2
15
Assemblytailrollsyste
m
3042
6
1
16
WasherM5FZB
8210
5900
8
17
A
REVISIONHISTORY
REV
DES
CRIPTION
DATE
APPR
OVED
A
Made
31-05-2010
kc
47
16
117
3
15
9
11
14
12
13
8
10
5
15
15
26
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
30/80
PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangivettoleranceriht./Notspecificedtoleranceaccordingto:
Material:
Scale:
Overfl.beskaffenhed/Surfaceproperties:
Konst./Designed:
Tegnet/Drafted:
Date:
Description:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsaved:
Sheetsize:
DS/ISO2768-m
Sheet
/
Thisdocumentisstrictlyconfidentialandmustonnoaccountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
2
KC
05-12-2005
Fra
meforspadelift2010
A2
27-05-2010
1
207945
KC
Allekanterreife
s
Breakealledge
s
DESCRIPTION
PARTNUMBER
QTY
ITEM
B
olt.unbracocyl4x16FZB
10204016
12
1
B
oltunbrakocyl6x12FZB
10206012
2
2
B
olt.unbracocyl6x16FZB
10206016
4
3
B
oltunbracocyl6x20FZB
10206020
8
4
B
olt.unbracocyl8x12FZB
10208012
2
5
B
olt.unbracocyl8x20FZB
10208020
2
6
B
oltUnbrakocyl.8x30FZB
10208030
6
7
B
oltUnbrakocyl8x35FZB
10208035
2
8
H
exagoncountersunkhead6x25FZB
20406025
2
9
H
exagoncountersunkhead8x16FZB
20408016
4
10
H
exagoncountersunkhead8x20FZB
20408020
4
11
S
ensorbracketfortower2010
207861
1
12
R
einforcementfortowermodelES
207880
1
13
C
onsolefortowermodel2008
207885
1
14
H
orisontialconsolefortower_M2008
207887
1
15
C
onnectionplate-spadecylinder_ES
207890
1
16
H
orisontialconsolemodelES
207895
1
17
B
allrunnerblocksize15
207981
2
18
B
allguiderailsize15-710
207983
1
19
C
ylinderPRA/182040/M/500
212129
1
20
F
-JointQM-8040-25
214120
1
21
L
-JointQA-8040-24
214160
1
22
R
eedsensoryellow
214312
2
23
S
ocketwith3Mwire
214314
2
24
B
anjoflowcontrol61/4"
215992
2
25
B
allrunnerblocksize25
222300
2
26
C
lampingplateforAT10
30268
1
27
B
racketassemblyfortowerlift
30291
1
28
C
onnectionplateforbelt
30700
1
29
B
racketforenergichain
30820
1
30
W
asherM6FZB
82106000
2
31
W
asherM8FZB
82108000
2
32
REVIS
IONHISTORY
REV
DESCRIPT
ION
DATE
APPROVED
A
Made
27-05-2010
kc
6
32
1
19
16
28
21
20
13
10
23
24
18
18
24
23 3 4 91
722
7
8
12
31
2
26
29
30 5 4 2
726
11
15
14
25
2
5
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
31/80
PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangivettoleranceriht./Notspecificedtoleranceaccordingto:
Material:
Scale:
Overfl.beskaffenhed/Surfaceproperties:
Konst./Designed:
Tegnet/Drafted:
Date:
Description:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsave
d:
Sheetsize:
DS/ISO2
768-m
Sheet
/
Thisdocumentisstrictlyconfidentialandmustonnoaccountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
2
KL
KC
12-05-2004
Assemblyleghookandtailrollsystem2
010
A3
31-05-2010
1
207954
KC
Allekanterreifes
Breakealledges
PartsList
DESCRIPTION
PAR
TNUMBER
QTY
ITEM
Leftleghooksystem2
010
2079
49
1
1
Rightleghooksystem
2078
48
1
2
Tailspadesystem2
010
2079
51
1
3
REVISION
HISTORY
REV
DES
CRIPTION
DATE
APPR
OVED
A
Made
31-05-2010
kc
1
3
2
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
32/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
33/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
34/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
35/80
ID-Nr./PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangivettoleranceriht./
Notspecificedtoleranceaccordingto:
Materiale/
Material:
Skala/Scale:
Overfl.bes
kaffenhed/
Surfacepr
operties:
Vgt/Weight:
Konst./Designed:
Tegnet/Drafted:
Dato/Date:
Filnavn/Filename:
Beskrivelse:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsaved:
Papirstrrelse/Sheetsize:
DS/ISO2768-m
kg
sheet
of
Thisdocumentisstrictlyconfidentialandmustonnoaccountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
2
ThomasVittrup
02-06-2010
CompletebodyholdersystemM2010
207967CompletebodyholdersystemM2010
.iam
A2
02-0
6-2010
CombiCut
1:2
TV
1
207967
PartsListDESCRIPTION
PARTNUMB
ER
QTY
ITEM
Bolt.unbracocyl6x16FZB
10206016
4
1
Boltunbracocyl6x20FZB
10206020
4
2
Boltunbracocyl6x25FZB
10206025
4
3
Bolt.unbracocyl8x12FZB
10208012
2
4
Bolt.unbracocyl8x16FZB
10208016
12
5
Bolt.unbracocyl8x20FZB
10208020
2
6
Hexagoncountersunkhead6x12FZB
20406012
8
7
Hexagoncountersunkhead8x16FZB
20408016
8
8
HingeGN237-60-60
207940
2
9
CylinderRA/192032/M/20
210330
1
10
LocknutMP150189_
M10x1,25
210427
1
11
LocknutMP150190_
M12x1,25
210428
1
12
CylinderPRA/182040/M/80
212123
1
13
F-JointQM-57040-25
214108
1
14
F-JointQM-8025-25
214115
1
15
Reedsensoryellow
214312
1
16
Socketwith3Mwire
214314
1
17
R-JointQA-8040-27
214905
1
18
Swirvelelbow6mm1/8"
215760
2
19
Straightconnector61/4"
215930
2
20
Assemblybracketfor32cylinder
30641
1
21
Ass.unitexcentricbodyholder
30667
1
22
Stopaxlecomplete
30702
1
23
Bodyholderforouterplate
30705
1
24
Bodyholderforouterplate
30706
1
25
Bodyholderforinnerplate
30710
1
26
Bodyholderforinnerplate
30711
1
27
Assemblybodyholder
30716
1
28
Lowerplatefortigh-support
30740
2
29
Assemblytigh-supportright
30756
1
30
Assemblytigh-supportleft
30757
1
31
Axleforcylinder32
30760
1
32
Axleforcylinder40
30761
1
33
Spacer19-12-24,8
30762
2
34
Spacer19-12-29,7
30763
2
35
Plateforbodyholderrubber
30765
1
36
Rubberforbodyholderplate
30770
1
37
WasherM6FZB
82106000
20
38
WasherM8FZB
82108000
16
39
REVISIONHISTORY
REV
DESCRIPTION
DATE
APPROVED
A
Newdrawing
02-06-2010
KL
22
31
26 7 9 8 2 3
829 7 2
8 4 5 39
24
14
12
13
20
16
17
30
15
19
19
32
38
35
21
20
34 3 1
833162
310
11
25
27
37
36
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
36/80
ID-Nr./PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangiv
ettoleranceriht./
Notspecificedtoleranceaccordingto:
Materiale/Material:
Skala/Scale:
Overfl.beskaffenhed/
Surfaceproperties:
Vgt/Weight:
Konst./Designed:
Tegnet/Drafted:
Dato/Date:
Filnavn/Filename:
Beskrivelse:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsaved:
Pa
pirstrrelse/Sheetsize:
DS/ISO2768-m
kg
sheet
of
Thisdocumentisstrictlyconfidentialandmustonnoaccountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
1
ThomasVittrup
14-05-2004
Ass.unitexcentricbo
dyholder
30667Ass.unitexcentricbodyholde.iam
A3
17-05-2004
1:1
TV
1
30667
PartsList
DESCRIPTION
PARTNUMBER
Q
TY
ITEM
StopscrewM5-10FZB
20905010
4
1
Bodyholderhoo
kleft
30665
1
2
Bodyholderhoo
kright
30666
1
3
Braceforcylinde
rbody-holderleft
30670
1
4
Braceforcylinde
rbody-holderright
30671
1
5
Bottompartfbodyhook
30675
1
6
Bushingforbodyhook20-10,2-15,8
30680
2
7
Bushingforbodyhook
30682
4
8
Eccentricforbodyholdsystem
30685
1
9
Bracketforbodysholdsystem
30690
1
10
Axelforbodyho
ldersystem
30731
2
11
Axelforbodyho
ldersystem
30732
3
12
Hexagoncounte
rsunkhead6x16Kval.12.9
53406016
6
13
4xDrillintoshaft
4xCleanwithMA
-4000MetalKlene
4xLockwithLoct
ite243
6xCleanwithMA
-4000Metal-Klene
6xLockwithLoctite243
13
5
8
7
1
3
11
10
9
2
8
7
8
4
13
6
12
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
37/80
B-B
(1:2)
ID-Nr./PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangiv
ettoleranceriht./
Notspecificedtoleranceaccordingto:
Materiale/Material:
Skala/Scale:
Overfl.beskaffenhed/
Surfaceproperties:
Vgt/Weight:
Konst./Designed:
Tegnet/Drafted:
Dato/Date:
Filnavn/Filename:
Beskrivelse:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsaved:
Pa
pirstrrelse/Sheetsize:
DS/ISO2768-m
kg
sheet
of
Thisdocumentisstrictlyconfidentialandmustonnoaccountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
1
ThomasVittrup
14-05-2004
Assemblybodyholder
30716Assemblybodyholder.iam
A3
17-05-2004
1:2
WeldedSteelMild
TV
1
30716
PartsList
DESCRIPTION
PA
RTNUMBER
QTY
ITEM
FittingboltM6-8x12
mm
20
206012
1
1
StopscrewM5-5FZB
20
905005
2
2
LocknutMP150189_
M10x1,25
21
0427
1
3
CylinderRM/8026/M/125
21
1005
1
4
Banjoflowcontrol
61/8"
21
5105
2
5
Col.pipelineforbodyholder
30
715
1
6
Axleforpipe-bodyholderlock
30
725
1
7
Roundsteelforbodylock
30
730
1
8
B
B
90,0
0
2
6
5
8
3
2-01
+
Drillintoshaft
CleanwithMA-4000Metal-Klene
Loc
kwithLoctite248
Lubricatewithcoppergrease
1
Cleanwit
hMA-4000Metal-Klene
Lockwith
Loctite248
4
7
Cylinder
adjusting:
Thebolt
muststop2mmbeforetheendofthegroove.
REVISIONHISTORY
REV
DESCRIPTION
DATE
APPROVED
A
Made
17-05-2004
B
Renamed,Loctitetypechanged
11-06-2010
KC
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
38/80
ID-Nr./PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangivettoleranceriht./
Notspecificedtoleranceaccordingto:
Materiale/
Material:
Skala/Scale:
Overfl.bes
kaffenhed/
Surfaceproperties:
Vgt/Weight:
Konst./Designed:
Tegnet/Drafted:
Dato/Date:
Filnavn/Filename:
Beskrivelse:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsaved:
Papirstrrelse/Sheetsize:
DS/ISO2768-m
kg
sheet
of
Thisdocumentisstrictlyconfidentialandmustonnoaccountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
2
ThomasVittrup
01-06-2010
Assemblycrosscutknife2010
207862Assemblycrosscutknife2010.iam
A2
01-0
6-2010
1:2
Welde
dSteelMild
TV
1
207862
PartsList
DESCRIPTION
PARTNUMBER
QTY
ITEM
Boltunbrakocyl5x12FZB
10205012
4
1
Bolt.unbracocyl8x16FZB
10208016
4
2
BoltUnbrakoCyl.8x25FZB
10208025
1
3
He
xagonboltm6x16FZB
11406016
2
4
He
xagonboltm6x20FZB
11406020
3
5
He
xagonboltm8x25FZB
11408025
2
6
He
xagonbolt10x45FZB
11410045
1
7
Nu
tM6FZB
1506000
2
8
Self-lockingnutM6FZB
17906000
1
9
Self-lockingnutM8FZB
17908000
3
10
Self-lockingnutM10FZB
17910000
1
11
FittingboltM6-8x16mm
20206016
1
12
He
xagoncountersunkhead6x12FZB
20406012
2
13
Hu
bforcrosscutknife
205918
1
14
Knifeforslicingmachine50mm
206060
1
15
Lockforknife
206061
1
16
Air
motorLZB22A049-55
206084
1
17
Assemblyconsole-bracket2010
207854
1
18
Screenfor50knife
207857
1
19
Bracketforknivescreen
207863
1
20
CylinderRA/192020/M/25
210300
1
21
LocknutM/P1501/60
210421
1
22
Re
edsensoryellow
214312
1
23
Socketwith3Mwire
214314
1
24
Str
aightconnector61/8"
215900
2
25
Banjoflowcontrol4M5
215980
2
26
Do
ublestraightconnector6mm
216615
1
27
Silencer1/8"T40C-1800
216796
1
28
Ballrunnerblocksize25
222300
1
29
Bracketforcrosscutknife
30390
1
30
Assemblymountingplatefor
30442
1
31
Assemblyspringsystem
30467
1
32
Bracketforpullingof
30470
1
33
Cla
mpingplateforAT5
30598
1
34
Assemblymountingbracket
30644
1
35
Wa
sherM5FZB
82105900
4
36
Wa
sherM6FZB
82106000
4
37
Wa
sherM8FZB
82108000
8
38
REVISIONHISTORY
REV
DESCRIPTION
DATE
APPROVED
A
Newdrawing
01-06-2010
KL
16
15
14
17
28
19
20
37
4
8
4
18
8
5
30
2
38
31
13
29
5 37
33
34
10
38
38
6
1
3
10
36
35
26
23
24
26
21
32
1293
727
25
7
11
22
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
39/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
40/80
PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangivettoleranceriht./Notspecificedtoleranceaccordingto:
Material:
Scale:
Overfl.beskaffenhed/Surfaceproperties:
Konst./Designed:
Tegnet/Drafted:
Date:
Beskrivelse:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsaved:
Sheetsize:
DS/ISO2768-m
Sheet
/
Thisdocumentisstrictlyconfidentialandmustonno
accountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
2
KL
26-05-2010
Pawcutsystem_
2010-Left
A3
26-05-2010
1
207969
Combi/Quickcut
KL
1:2
Allekanterreifes
PartsList
DESCRIPTION
PARTNUMBER
QTY
ITEM
Bolt
.unbracocyl4x10FZB
10204010
4
1
Bolt
.unbracocyl4x12FZB
10204012
2
2
Bolt
.unbracocyl4x16FZB
10204016
2
3
Bolt
.unbracocyl4x18FZB
10204018
4
4
Bolt
unbrakocyl5x12FZB
10205012
2
5
Bolt
unbrakocyl6x12FZB
10206012
2
6
Hex
agonboltm5x20FZB
11405020
1
7
Hex
agonboltm5x35FZB
11405035
1
8
Self
-lockingnutM5FZB
17905000
1
9
Hex
agoncountersunkhead4x10FZB
20404010
4
10
Hex
agoncountersunkhead6x12FZB
20406012
2
11
Paw
knifeCCHSS110-62-40-4mm
207825
1
12
SlideBearingGFM-1416-21
207840
2
13
Gas
spring6x5050N
207875
1
14
CylinderRA/192032/M/20
210330
1
17
LocknutMP150189_
M10x1,25
210427
2
18
GroovenutMP72816
214184
8
19
Mou
ntingplateforleftpawkniferail
30237
1
21
Top
forconsole,pawknife
30238
1
22
Bracketforpawknife
30250
1
23
Bracketforgasspring,pawcut
30253
1
24
Pelletforgasspring
30254
1
25
Mou
ntingpieceforleftpawknife
30285
1
26
Assembly,branchforturning
30323
1
27
WasherM4FZB
82104000
10
28
WasherM5FZB
82105900
3
29
WasherM6FZB
82106000
2
30
Left
Screenforpawblow
207976
1
67
Stra
ightconnector6mm1/8"
216520
2
68
Swirvelelbow6mm1/8"
215760
1
69
Ball
guiderailsize15-95
207984
1
70
Ball
runnerblocksize15
207982
1
71
28
22
11
21
17
19
10
2
2651
218
23 3
29
9
14
25
24
8
7
6
27
13
30
30
4
28
2912
8
Breakalledges
68
67
71
7
0
69
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
41/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
42/80
PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangivettoleranceriht./Notspecificedtoleranceaccordingto:
Material:
Scale:
Overfl.beskaffenhed/Surfaceproperties:
Konst./Designed:
Tegnet/Drafted:
Date:
Beskrivelse:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsaved:
Sheetsize:
DS/ISO2768-m
Sheet
/
Thisdocumentisstrictlyconfidentialandmustonno
accountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
2
KL
26-05-2010
Pawcutsystem_
2010-Right
A3
26-05-2010
1
207973
Combi/Quickcut
KL
1:2
Allekanterreifes
PartsList
DESCRIPTION
PARTNUMBER
QTY
ITEM
Bolt
.unbracocyl4x10FZB
10204010
4
1
Bolt
.unbracocyl4x12FZB
10204012
2
2
Bolt
.unbracocyl4x16FZB
10204016
2
3
Bolt
.unbracocyl4x18FZB
10204018
4
4
Bolt
unbrakocyl5x12FZB
10205012
2
5
Bolt
unbrakocyl6x12FZB
10206012
2
6
Hex
agonboltm5x20FZB
11405020
1
7
Hex
agonboltm5x35FZB
11405035
1
8
Self
-lockingnutM5FZB
17905000
1
9
Hex
agoncountersunkhead4x10FZB
20404010
4
10
Hex
agoncountersunkhead6x12FZB
20406012
2
11
Paw
knifeCCHSS110-62-40-4mm
207825
1
12
SlideBearingGFM-1416-21
207840
2
13
Gas
spring6x5050N
207875
1
14
RightScreenforpawblow
207974
1
15
Ball
runnerblocksize15
207982
1
16
Ball
guiderailsize15-95
207984
1
17
CylinderRA/192032/M/20
210330
1
18
LocknutMP150189_
M10x1,25
210427
2
19
GroovenutMP72816
214184
8
20
Swirvelelbow6mm1/8"
215760
1
21
Stra
ightconnector6mm1/8"
216520
2
22
Mou
ntingplaterforrightpawkniferail
30231
1
23
Top
forconsole,pawknife
30238
1
24
Bracketforpawknife
30250
1
25
Mou
ntingpiece,rightpawknife
30251
1
26
Bracketforgasspring,pawcut
30253
1
27
Pelletforgasspring
30254
1
28
Assembly,branchforturning
30323
1
29
WasherM5FZB
82105900
1
30
WasherM6FZB
82106000
2
31
18
20
4
11
24
23
10
31
7
8
6
19
27
14
9
12
26 15
28
25
30
3
29
13
Breakalledges
REVISIONHISTORY
REV
DESCRIPTION
DATE
APPROV
ED
A
Newdrawing
06-03-2007
KL
22
21
15
16 1
7
2
2
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
43/80
PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangivettoleranceriht./Notspecificedtoleranceaccordingto:
Material:
Scale:
Overfl.beskaffenhed/Surfaceproperties:
Konst./Designed:
Tegnet/Drafted:
Date:
Beskrivelse:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsaved:
Sheetsize:
DS/ISO2768-m
Sheet
/
Thisdocumentisstrictlyconfidentialandmustonno
accountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
1
KL
02-03-2007
Gearfortower
A3
05-03-2007
1
207852
Allekanterreifes
Parts
List
DESCRIPTION
PARTNUMBER
QTY
ITEM
B
oltUnbracocyl3x8FZB
10203008
2
1
H
exagonboltm8x16FZB
11408016
1
2
G
earmotorhigh-effectwithbreake
207902
1
3
K
ey8x7x32mmDIN-6885A
207947
2
4
E
ncoderType8.5020.C922.0500
207956
1
5
S
topscrewM5-10FZB
20905010
1
6
S
haftforencoder
30171
1
7
B
racketforencoder
30172
2
8
P
ulleyAT10Z24-gearside
30266
1
9
S
pacerforlargegear
30267
1
10
S
haftforlargegearmotor
30775
1
11
N
utforlargegearmotor
30776
1
12
W
ashertypeSRKB9x35x3
4809335
1
13
W
asherTypeSRKB14x35x3
4814335
1
14
W
asherM3FZB
82103000
2
15
14
1283
114
56 7
2 13 9 1
0
REVISIONHISTORY
REV
DESCRIPTION
DATE
APPROVED
A
Made
20-05-2010
KC
4
15 1 1 1
5
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
44/80
PartNo.:
Udfoldetiht./Unfoldingaccordingto:
Ikkeangivettoleranceriht./Notspecificedtoleranceaccordingto:
Material:
Scale:
Overfl.beskaffenhed/Surfaceproperties:
Konst./Designed:
Tegnet/Drafted:
Date:
Beskrivelse:
Description:
Sidstgemtaf/Lastsavedby:
Sidstgemt/Lastsaved:
Sheetsize:
DS/ISO2768-m
Sheet
/
Thisdocumentisstrictlyconfidentialandmustonno
accountbecopiedordisclosedtoanythirdperson.
HEDENSTEDGRUPPENA/S
1
KL
05-03-2007
Gearforcrossentknife
A3
06-03-2007
1
207853
Allekanterreifes
PartsList
DESCRIPTION
PARTNUMBER
QTY
ITEM
BoltUnbracocyl3x8FZB
10203008
2
1
Bolt.unbracocyl4x10FZB
10204010
2
2
Boltunbrakocyl5x20FZB
10205020
4
3
Boltunbracocyl6x20FZB
10206020
1
4
Stopscrew4x5black
10504005
1
5
NutM5FZB
1505000
4
6
NutM12FZB
1512000
1
7
GearmotorRMI28S56B14
207904
1
8
Key5x5x25mmDIN-6885A
207946
2
9
EncoderType8.5020.C922.0500
207956
1
10
Smallenginebracket
30144
1
11
Shaftforencoder
30171
1
12
Bracketforencodercrosscutknife
30173
1
13
PulleyAT5Z32gearside
30600
1
14
Shaftforcrosscutknife
30780
1
15
WasherM3FZB
82103000
2
16
WasherM4FZB
82104000
2
17
WasherM5FZB
82105900
8
18
WasherM12FZB
82112000
1
19
Washer6,5x16,5x3FZB
87606000
1
20
REVISIONHISTORY
REV
DESCRIPTION
DATE
APPROVED
A
Made
19-05-2010
KC
1
011
6
1
271
9
1
321
7
1
331
181
86
155991
4204
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
45/80
Telephone 0045 75891244
- for professionel farmes 45
13. FAQ
Problem Cause Solution
When I put the mink in and stepthe pedal the paw is pulled out ofthe paw holder?
The stretch pressure is toohigh or there is dirt in theslide
Reduce the stretch pressure,and if it does not help, dismountthe air of the machine, clean anmassage the slide.
The cross-section is not quiet overthe mink, even though I have justput it in?
The paw holders are mutualincorrectly adjusted.
Adjust the screws, which aremarked with 2a on figure 2, sothat the line between the two isquite right.
When I make a triangle cut, the cutis not deep enough?
The spade does not cutdeep enough in the mink.
Adjust the depth in vertical dataon the operating panel
When the legs are being loosened,
the skin bursts on the thigh?
The cross cut is laid too faron the belly side of the legs,
therefore it does not crossthe paw blades.
Too much meat is left on thethighs by loosening the legs?
The hooks do not close farenough round or it isbended.
Figure 1- open the hooks a littlebit more with the adjustmentscrew
I have opened the hooks, but itdoes not help?
Adjust the depth on the hind legloosener in the operating panel(vertical data), they have to beplaced about 3-4 mm under thethigh holder.
Even though I close the hookscorrectly round the thighs, it does
not loosen well?
The hook does not close farenough round or it is
bended
Try to increase the length andstroke, so that the balls just pass
each other.If defect then change the hook.
The tail spade makes a hole in theskin when it runs down?
The tail is stretched to hardout, or there can be a burron the side of the spade.
I have closed the tail hook andwant to complete the skin, but themachine stops?
The signal for completing ismissing, probably becausesome dirt is in the lock tothe body holder.
Press reset on the panel, cleanthe lock and run the body again
I have cleaned the lock, but still it
does not work?
When you run big minks, itcan happen, that the body
holder do not get far enoughround to lock
Fig. 3 At repeatable cases, tryto increase the length of strokeby raising the cylinder 3-4mm
(3a). At the same time lower thehind leg holder similar.
The tail is not cut up properly?
The tail roll is wrongadjusted, or it does not getclose enough to the blade.The blade can be deaf.
Check that the tail roll attach canmove unhindered in the lengthdirection, clean for dirt.Sharpen the blades if necessary.
I have tried the variouspossibilities, but still it does notwork?
Dismount the air of the machineand check that the tail roll canreach right to the blades. The tailroll has to be placed right
beneath the centre of the blades.
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
46/80
Telephone 0045 75891244
- for professionel farmes 46
Fig. 2
2
2a
Fig. 1
1
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
47/80
Telephone 0045 75891244
- for professionel farmes 47
Fig. 3
3
3a
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
48/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
49/80
ODS-0566-S1
Drawing no. Date: 29-6-2010Parts of list Design: Peter DamsgrdDrawing A4-10774
Item No. Descreption Norgren Ident. no.
1 1 Cyl C1 PRA/182032/M/3202 1 F-Mounting QM/8025/253 1 L-Mounting QA/8032/244 1 Swivel C024706185 1 Banjo flow control V20 C0L5106186 1 Valve V19 R07-100-RNEG7 1 Bracket M/P71273/38 1 Gauge M1 18-013-0119 2 Swivel C0247061810 1 Mounting nut 2962-041112 1 Cyl C2 PRA/182040/M/50013 1 F-Mounting QM/8040/2514 1 L-Mounting QA/8040/2415 2 Banjo flow control V23-V24 C0K51062816
17 2 Cyl C3-C4 RT/57225/M/5018 2 F Mounting QM/57025/2519 2 Nut M/P1501/8920 2 Straight adaptor C0125061821 2 Banjo flow control V25-V26 C0TA006182223 1 Cyl C4-2 RM/8026/M/8024 1 F Mounting QM/8025/2525 1 Banjo flow control V32 C0K51061826 1 Swivel C02470618
27 1 Silencer 10011060028 1 Swivel Y adaptor C008206002930 1 Cyl C5 RA/192032/M/80
31 1 Nut M/P1501/89
32 2 Banjo flow control V21-V22 C0K510618
33
34 1 Cyl C6 RT/57225/M/50
35 1 Nut M/P1501/89
36 1 UF-Mounting QM/8025/32
37 1 L-Mounting QM/57025/2438 2 Banjo flow control V33-V34 C0TA00618
Hedensted Gruppen A/SODS-0566-35314-A1
ODS-0566-S1Combicut 2010
21-6-2010 Side 1
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
50/80
ODS-0566-S1
39 2 Swivel Y adaptor C00820600
4041 1 Cyl C7 RA/192032/M/20
42 1 F Mounting QM/8025/25
43 1 Nut M/P1501/89
44 2 Swivel C02470618
45
46 2 Cyl C8-C9 RA/192032/M/25
47 2 F Mounting QM/8025/25
48 2 Nut M/P1501/89
49 4 Swivel C02470618
50 2 Swivel Y adaptor C0082060051
52 2 Cyl C10-C11 RA/192032/M/20
53 4 Nut M/P1501/8954 4 Straight adaptor C0225061855
21-6-2010 Side 2
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
51/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
52/80
ODS-0566-S2
Drawing no. Date: 29-6-2010Parts of list Design: Peter DamsgrdDrawing A4-10774
Item No. Descreption Norgren Ident. no.
1 1 Cyl C12 RM/8026/M/1252 2 Banjo flow control V35-V36 C0K510618
3 2 Swivel Y adaptor C0082060045 1 Cyl C13 PRA/182040/M/806 1 F-Mounting QM/57040/257 1 R-Mounting QA/8040/278 2 Straight adaptor C02250628910 1 Cyl C14 RA/192020/M/2511 1 Nut M/P1501/6012 2 Banjo flow control V37-V38 C0K510405
1314 2 Cyl C15-16 RA/192032/M/8015 2 F-Mounting QM/8025/2516 2 Nut M/P1501/8917 4 Banjo flow control V28-V31 C0K5104181819 1 Cyl C17 RA/192025/M/2520 1 F-Mounting QM/8020/2521 1 Nut M/P1501/6022 2 Swivel C024704052324 1 Cyl C18 RA/192032/M/50
25 2 Nut M/P1501/89
26 2 Swivel C02470618
Hedensted Gruppen A/SODS-0566-35314-A2
ODS-0566-S2Combicut 2010
21-6-2010
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
53/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
54/80
ODS-0566-S3
Drawing no. Date: 29-6-2010Parts of list Design: Peter DamsgrdDrawing A4-10774
Item No. Descreption Norgren Ident. no.
1 1 Air Motor M01 LZB22A049-552 1 Silencer T40C18003 2 Straight adaptor C022506184 1 Straight union C0020060056 2 Air Motor M02-M03 LZB22A049-557 4 Swivel C024708188 2 Swivel C024708289 2 Silencer T40C1800
1011 1 Valve V17 V60A413A-A313J12 1 Connector M/P43313/313 1 Swivel C0247081814 1 Swivel C0247061815 1 Silencer T40C180016
17 1 Valve V18 V61B413A-A313J18 1 Connector M/P43313/3
19 2 Swivel C02470828
20 1 Silencer T40C2800
21 2 Swivel Y adaptor C00820800
22
23 1 Valve V19 V60A413A-A313J24 1 Connector M/P43313/325 2 Swivel C0247081826 1 Silencer T40C1800
27 1 Swivel Y adaptor C0082080628 2 Swivel C024706182930 1 Plug Male 23411002831 1 Adaptor 4215-0832 1 Filterregulator FR B72G-2GK-AL3-RMN33 1 Tamper resistant 4255-5134 1 Gauge 18-013-98935 2 Plug Male 16005002836 2 Quikclamp and Wall mount 4214-52
37 1 Quikclamp 4214-5138 1 Porting blok 4216-52
Hedensted Gruppen A/SODS-0566-35314-A3
ODS-0566-S3Combicut 2010
21-6-2010 side 1
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
55/80
ODS-0566-S3
39 1 Straight adaptor C0225102840 1 Lubricator L72M-2GP-ETN41 1 Swivel C024708284243 1 Swivel Tee adaptor C0267103844 1 Stem reducer C0023100845 1 Oil removal filter FF F73C-3GD-AT046 1 Swivel C0247103847 1 Union Tee C00601000
48 1 wall mounting bracket 4424-504950 1 Valve V1-V16 VM10160217251 2 Plug 6 11004060052 1 Cabel 3 m D Sub 90gr. V12088-E03
21-6-2010 side 2
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
56/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
57/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
58/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
59/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
60/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
61/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
62/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
63/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
64/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
65/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
66/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
67/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
68/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
69/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
70/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
71/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
72/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
73/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
74/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
75/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
76/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
77/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
78/80
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
79/80
Telephone 0045 75891244
- for professionel farmes 54
16. EC Declaration of Conformity
Hedensted Gruppen A/S
Vejlevej 15,
8722 Hedensted
- herewith declares that:
HG slicing machine Combi Cut
Typenummer 207802
- is in conformity with the provision of:
The Machinery Directive 2006/42/EF
The low Voltage Directive 73/23/EF
- and the following harmonised standards have been applied.
DS/EN 12100-1:2005
EN 60/439-3
DS/EN 13857:2008
1. november 2010
-
7/25/2019 Hg Combi Cut Touch 11.09.2011 Eng
80/80
Telephone 0045 75891244
17. Technical specifications
Voltage : 3x400V + N + PE
Connection : 16A CEE
PLC-control : 220 V/ 24 V DC
Pneumatic air : 7 bar
Air volume : Min. 500 l/min.
Air connection : Cejn 320 quick coupling
Kapacity : 180/350 mink pr. hour
Weight : 300 kg
Dimensions :
Width : 1400 mm
Transport hight : 2400 mm
Operating hight : 3000 mm
Length : 900 mm