HENSLEY J Gavilanes,Cuchillas,Puntas y Adaptadores

SafetyFirst: Hensley Industries recommends that you us a soft-faced hammer with suitable hand protection andANSI approved (Z87.1) eye protection while using our products.

REPLACEMENT WEAR

PARTS FOR

CATERPILLAR® MACHINERY

REVISED03-06

2

TABLE of CONTENTS

Replacement Compactor Parts ............................................................................4 - 5Compactor Feet ................................................................................. 4Cleaner Bars ................................................................................. 5

Heavy Duty Cast Edges & End Bits for Dozers ....................................................................6 - 12Edge Details ............................................................................ 7- 9End Bit Details ......................................................................... 9 - 12

Replacement Ripper Parts for Dozers & Loaders ............................................................ 13 - 19Ripper Parts Application Chart ............................................................................... 13Ripper Part Details (sorted by tooth series)

R550 Series ............................................................................... 14R500 Series ....................................................................... 14 - 15R450 Series ............................................................................... 16R350 Series ............................................................................... 17R300 Series ............................................................................... 18J250 Series ............................................................................... 18J200 Series ............................................................................... 18

Ripper Tooth Details ............................................................................... 19

Replacement Ripper Parts for Motorgraders ..........................................................................20

Replacement Scarifier Parts for Motorgraders .......................................................................21

Replacement Parts for Scrapers ....................................................................... 22 - 23

Box Ripper Systems for Excavators ........................................................................ 24 - 25

Replacement Parts for Backhoes & Excavators (Application Chart) .............................. 26 - 27

Replacement Parts for Loaders with Weld-On Adapter Systems (Application Chart) ... 28 - 29

Replacement Parts for Loaders with Bolt-On Adapter Systems(Application Chart) ..... 30 - 31

Replacement Modulok Parts for Loaders ....................................................................... 32 - 36Application Chart ....................................................................... 32 - 33Modulok Details ....................................................................... 34 - 36

Bolt-On Segments, Heel Plates and Top Covers for Loaders .......................................... 37 - 43Bolt-On Reversible Segment Details ............................................................................... 38Bolt-On Half Arrow Segment Details ....................................................................... 39 - 40Bolt-On Top Cover Plate Details ............................................................................... 41Bolt-On Heel Plate Details ....................................................................... 42 - 43

Bolt-On Half Arrow Edge Systems for Loaders ................................................................ 44 - 47Half Arrow Edge Application Chart ............................................................................... 46Half Arrow Edge Details ............................................................................... 47

Hensley Industries, Inc. • P.O. Box 29779 • 2108 Joe Field Road • Dallas, Texas 75229Customer Service (888) 406-6262 U.S./Canada (972) 406-6262 all other locations

Fax (888) 241-3274 U.S./Canada (972) 241-3274 all other locations

3

Replacement Teeth for Excavators, Loaders & Scrapers ............................................... 48 - 59Tooth Series Reference Chart ....................................................................... 48 - 49Tooth Pocket Details ............................................................................... 48Tooth Details ....................................................................... 50 - 60

Short ............................................................................... 50Long ............................................................................... 50Heavy Long ............................................................................... 51Tiger ............................................................................... 52Twin Tiger ............................................................................... 52Abrasion ............................................................................... 53All Purpose ............................................................................... 53AGB ............................................................................... 54Penetrator ............................................................................... 54Rock Penetrator (RP2 & RP3) ............................................................................. 55Rock Chisel ............................................................................... 56SYL ............................................................................... 56Old Style Flare ............................................................................... 57Standard Flare ............................................................................... 57Heavy Long Abrasion Ace ............................................................................... 58Rock Penetrator (RP2 & RP3) Abrasion Ace ..................................................... 59Heavy Duty Penetrator Abrasion Ace ................................................................. 60

Miscellaneous Adapters ............................................................................... 60Skid-Steer Bolt-On Adapter ............................................................................... 60

Miscellaneous Teeth ............................................................................... 611 pc. Bolt-On Teeth ............................................................................... 61Asphalt Knife ............................................................................... 61

Replacement Fastener Details ....................................................................... 61 - 62

Adapter Details ....................................................................... 63 - 69Bolt-On Corner Adapters for Loaders ............................................................................... 633 Hole Bolt-On Adapters for Loaders ............................................................................... 632 Hole Bolt-On Adapters for Loaders ............................................................................... 64"Old Style" Flush Mount Weld-On Adapters for Loaders ................................................. 65Current Flush Mount Weld-On Adapters for Loaders ...................................................... 65Wrap-Around Weld-On Adapters for Loaders ............................................................ 66 - 67Wrap-Around Weld-On Adapters for Backhoes & Excavators ......................................... 68Bottom Leg Weld-On Adapters ............................................................................... 69

Weld-On Noses ............................................................................... 69

Excavator Sidecutter Details ....................................................................... 70 - 71

Sidecutter Combination Plate Details ............................................................................... 72

Vertical Lock Teeth & Fasteners for Loaders ................................................................... 73 - 74

Cast Lips for RTBs ............................................................................... 75

Tooth/Machine Quick Reference Guide ............................................................................... 76

Plow Bolt Assembly Charts ............................................................................... 77

Notes ....................................................................... 78 - 83

TABLE of CONTENTS

All manufacturers' names, numbers, symbols, & descriptions are used for reference purposes only. It is not implied that any part listed is the product of these manufacturers.Cat® & Caterpillar® are registered trademarks of Caterpillar, Inc.

SPECIAL NOTE: All dimensions, unless otherwise noted, are: Inches (mm)

4

REPLACEMENT COMPACTORPARTS

TAMPING FOOTMODEL PART NO. STYLE PART NO. STYLE BASE* PIN**

815 8K9189HX Bolt-On 4V3851HX Weld-On 7K6957

815 8K9189WHX Weld-On

815B 2V7053HX Weld-On 4V3851HX 7K6957

824B 3S3992HX Pin-On 7K9937P

824B 7K2939HX Pin-On 7K2939HX Pin-On 9S1645 7K9535P

825B 7K2939HX Pin-On 9S1645 7K9535P

825C 3S3992HX Pin-On 7K9937P

825C 8K9171HX Bolt-On 4V0668HX Weld-On 7K7071

834 3S3992HX Pin-On 7K9937P

834 7K2939HX Pin-On 7K2939HX Pin-On 9S1645 7K9535P

835 7K2939HX Pin-On 7K2939HX Pin-On 9S1645 7K9535P

835 8K9171HX Bolt-On 7K6015

ROCK TAMPING FOOT

* Part numbers shown in bold italics are for reference only and are not available from Hensley Industries.** See page 63 for pin detail.

PART TYPENO. A B C D E F LBS. KGS.

7K2939HX 5 8-7/8 (226) 3-3/4 (95) 4-7/8 (124) 4-1/16 (103) 3/4 (19) 13.8 6.3

8K9171HX 1 9-1/16 (230) 3-1/16 (78) 3-3/16 (81) 1-9/16 (40) 5-3/4 (146) 15/16 (24) 13.6 6.2

8K9189HX 1 6-11/16 (170) 2-3/4 (70) 2-1/2 (64) 1-9/32 (33) 4-1/2 (114) 21/32 (17) 8.2 3.7

8K9189WHX 2 7-1/8 (181) 3-1/8 (80) 1-3/4 (44) 1-3/16 (30) 5.3 2.4

2V7053HX 3 6-5/8 (168) 3-3/16 (81) 2-13/16 (71) 1-5/8 (41) 8.0 3.6

4V0668HX 4 8-7/16 (214) 3-7/16 (87) 3-1/2 (89) 1-15/16 (49) 16.2 7.3

4V3851HX 4 6-11/16 (170) 3-3/16 (81) 2-13/16 (71) 1-5/8 (41) 10.0 4.5

3S3992HX 6 5-1/16 (129) 3-9/16 (91) 4-1/16 (103) 3-5/16 (84) 25/32 (20) 9.5 4.3

WEIGHT

TYPE 3

TYPE 4 TYPE 5 TYPE 6

TYPE 2TYPE 1

COMPACTOR FEET

DIMENSIONS - Inches (mm)

5

Compactor wheel cleaner bar forCaterpillar® model 815B. Requires(2) 7/8" X 10" grade 8 hex head capscrews. Utilizes 3G8250HX flare tooth,9J2258P pin & 3G9609W washer.(See pages 62 - 63 for pin & washer details)

3G8250HXCLEANER BAR TOOTH

wt. = 9.2 lbs. 4.2 kgs.

5V4311HXCLEANER BAR

wt. = 21.1lbs. 9.6 kgs.

106-2047HXCLEAN-OUT BARwt. = 17.0 lbs. 7.7 kgs.

Compactor wheel clean-out bar forCaterpillar® model 815B.

REPLACEMENT COMPACTORPARTS - cont'd.

CLEANER BARS

141-7407HXCLEAN-OUT BARwt. = 9.7 lbs. 4.4 kgs.

Compactor wheel clean-out bar forCaterpillar® model 815B and 815F.

6

MACHINEMODEL

SERIALNO.

D11 4BB, 4KB, 9NH, LA6257HHDHX, 1 req’d. LA6258HHD-HX, 2 req’d. 8E4545RH, 1 req’d.1AD, 4CA, 5TB, (9) A114-514 (9) A114-514 (9) A114-5149MH, 9ZH, 4YP LA6259HHD-HX, 2 req’d. 8E4546LH, 1 req’d.

(9) A114-514 (9) A114-514

D10N, D10R - 10U 1SH, 7WH, LA6226HHD-HX, 3 req’d. LA6227HHD-HX, 2 req’d. 8E4541HDR, 1 req’d. 8E4541RH, 1 req’d.4LP, 6FP (5) A114-514 (5) A114-514 (7) A114-500 (7) A114-400

8E4542HDL, 1 req’d. 8E4542LH, 1 req’d.(7) A114-500 (7) A114-400

D10N, D10R - 10SU 1RH, 7RH LA6248HHD-HX, 2 req’d. LA6227HHD-HX, 2 req’d. 8E4541HDR, 1 req’d.4KP, 6EP (6) A114-500 (5) A114-514 (7) A114-500

8E4542HDL, 1 req’d.(7) A114-500

D9N, D9R - 9U 1LH, 2ZH LA6224HHD-HX*, 2 req’d. LA6201HHD-HX, 2 req’d. 8E4539RH, 1 req’d.1MP, 7PH (8) A10-400 (5) A10-400 (7) A10-412

8E4540LH, 1 req’d.(7) A10-412

D9N, D9R - 9SU 1MH, 5BH LA6225HHD-HX, 2 req’d. LA6201HHD-HX, 2 req’d. 8E4539RH, 1 req’d.1LP, 2LP (6) A10-400 (5) A10-400 (7) A10-412

7NH 8E4540LH, 1 req’d.(7) A10-412

D9L - 9U 19Y1-1474 LA6178HHD-HX*, 2 req’d. LA6179HHD-HX*, 2 req’d. 8E4541HDR, 1 req’d.78S (9) A10-400 (6) A10-400 (7) A114-500

8E4542HDL, 1 req’d.(7) A114-500

D9L - 9SU 18Y1-1875 LA6110HHD-HX, 1 req’d. LA6182HHD-HX*, 2 req’d. 8E4541HDR, 1 req’d.52Y, 42S (7) A10-400 (8) A10-400) (7) A114-500

8E4542HDL , 1 req’d.(7) A114-500

D9H - 9U 14C, 19K LA6111HHD-HX, 3 req’d. LA6112HHD-HX*, 2 req’d. 7T4094RH, 1 req’d.78X (6) A10-400 (4) A10-400 (7) A10-412

7T4095LH, 1 req’d.(7) A10-412

D9-9SU 18Y, 52Y, 1U1545HX, 1 req’d.42S (7) A114-400

1U1546HX , 1 req’d.(7) A114-400

D8N - 8U 1JH, 2WP LA6222HHD-HX, 2 req’d. LA6223HHD-HX*, 2 req’d. 8E4537HX, 1 req’d.6AH, 9CH (6) A10-400 (5) A10-400 (7) A10-412

8E4538HX, 1 req’d.(7) A10-412

D8N - 8SU 1KH, 2PP LA6178HHD-HX*, 1 req’d. LA6201HHD-HX, 2 req’d. 8E4537HX, 1 req’d.2TP, 3MP (9) A10-400 (5) A10-400 (7) A10-412

8E4538HX, 1 req’d.(7) A10-412

D8L - 8SU 04Y1-1939 LA6181HHD-HX, 2 req’d. LA6184HHD-HX, 2 req’d. 7T4091RH, 1 req’d. 3G8317HX, 1 req’d.(6) A10-314 (5) A10-314 (7) A10-314 (7) A10-314

7T4090LH, 1 req’d. 3G8318HX, 1 req’d.(7) A10-314 (7) A10-314

9J1477HX, 1 req’d.(7) A10-314

9J1478HX, 1 req’d.(7) A10-314

HEAVY DUTYRIBBED END BIT

(#) nut/bolt assy.

STANDARD DUTYEND BIT

(#) nut/bolt assy.

CENTER EDGE(#) nut/bolt assy.

END EDGE(#) nut/bolt assy.

HEAVY DUTY CAST EDGES and END BITSFOR DOZERS

*Under development.

TYPICAL BLADE LAYOUT

7

MACHINEMODEL

SERIAL NO.

D8-8SU 29V, 30W, 9J1479RH, 1 req’d.60V (7) A10-314

9J1480LH, 1 req’d.(7) A10-314

D8-8SU 78C, 29E, 94E, 4J8849RH, 1 req’d.69E, 14J, 44K (7) A78-300

47K 4J8850LH, 1 req’d.(7) A78-300

834 - U 14 LA6250HHD-HX, 2 req’d. LA6251HHD-HX, 2 req’d. 3G8315HDR, 1 req’d. 4J8843RH, 1 req’d.(7) A78-300 (6) A78-300 (7) A78-300 (7) A78-234

3G8316HDR, 1 req’d. 4J8844LH, 1 req'd.(7) A78-300 (7) A78-234

D7-7SU 40B, 1JP, 9W6199HRH, 1 req’d.8LH (7) A78-234

9W6198HLH, 1 req’d.(7) A78-234

D7-7S 23F,31F, 9W6199HRH, 1 req’d.59F, 60K, (7) A78-23414H, 49K, 9W6198HLH, 1 req’d.64K, 53J, (7) A78-2346KB, 8NH

D7-7A 22F, 30F, 9W6199HRH, 1 req’d. 4J8843RH, 1 req’d.72F, 13F, (7) A78-234 (7) A78-23413H, 4EB 9W6198HLH, 1 req’d. 4J8844LH, 1 req’d

(7) A78-234 (7) A78-234

D6-6SU & 8AH, 1CH, 2NH, 9W1875RH, 1 req’d.CUSTOM WIDE SU 4PH, 8BH (6) A34-212

9W1876LH, 1 req’d.(6) A34-212

D6-6S-LGP 1AH, 2LH, 3FH, 4T4455RH, 1 req’d.1SP, 3HP (6) A34-212

4T4454LH, 1 req’d.(6) A34-212

D6-6S 4BH, 4T4455RH, 1 req’d.1DH1-599 (6) A34-2122HH, 3JH 4T4454LH, 1 req’d.

1AH (6) A34-212

95E, 46G 5J1419RH, 1 req’d.55G, 17H (6) A34-21421H, 63S 5J1420LH, 1 req’d.

(6) A34-214

D6-6A 44E, 47G 4J8261RH, 1 req’d.58G, 18H, (6) A34-214

54U 4J8262LH, 1 req’d.(6) A34-214

3EH 4T4455RH, 1 req’d.1BH1-569 (6) A34-2144DH, 4LH 4T4454LH, 1 req’d.

(6) A34-214

D5-5A 91H, 96H, 42K, 4J8261RH, 1 req’d.11J, 13J, 98H, (6) A34-214

93H1-3846 4J8262LH, 1 req’d.93H3847-up (6) A34-214

6RH

CENTER EDGE(#) nut/bolt assy.

END EDGE(#) nut/bolt assy.

STANDARD DUTYEND BIT

(#) nut/bolt assy.

HEAVY DUTYRIBBED END BIT

(#) nut/bolt assy.

DOZER EDGES - Inches (mm)

CENTERS

LA6226HHD-HXwt.= 240.0 lbs. 108.9 kgs.

8

DOZER EDGES cont’d. - Inches (mm)

CENTERS cont’d.


CENTER EDGE

PART NO. A B C D E LBS. KGS.

LA6250HHD-HX 42-3/16 (1072) 10 (254) 1-3/4 (44) 3-1/16 (78) 6 (152) 164.0 74)

LA6110HHD-HX 40-7/8 (1038) 13 (330) 1-3/4 (44) 2-7/16 (62) 6 (152) 215.0 97.5

DIMENSIONS - Inches (mm) WEIGHT

ENDS

CENTER EDGE


LA6184HHD-HX 31-3/4 (806) 10 (254) 1-3/4 (44) 3-3/8 (86) 6 (152) 127.0 57.6

LA6201HHD-HX 31-7/16 (798) 13 (330) 1-3/4 (44) 2-7/8 (73) 6 (152) 162.0 73.5

LA6227HHD-HX 33-7/8 (860) 16 (406) 2 (51) 4-5/8 (117) 6 (152) 234.0 106.2


CENTER EDGE


LA6181HHD-HX 33-3/4 (857) 10 (254) 1-3/4 (44) 1-7/8 (48) 6 (152) 135.0 61.2

LA6111HHD-HX 35-7/16 (900) 13 (330) 1-3/4 (44) 2-23/32 (69) 6 (152) 185.0 83.9

LA6222HHD-HX 35-1/2 (902) 13 (330) 1-3/4 (44) 2-3/4 (70) 6 (152) 185.0 83.9

LA6225HHD-HX 35 (889) 13 (330) 1-3/4 (44) 2-1/2 (64) 6 (152) 190.0 86.2

LA6248HHD-HX 39 (991) 16 (406) 2 (51) 4-1/2 (114) 6 (152) 276.0 125.2

WEIGHT

NOTE:Non dimensioned bolthole locations are on 3"or 6" centers.


9

END BIT DETAILS - Inches (mm)

END BITPART NO. A B C D E F G H I J LBS. KGS.

5J1419RH& 15 (381) 9-3/4 (248) 13-3/4 (349) 8-1/8 (206) 2-3/16 (56) 15/16 (24) 4 (102) 2-1/2 (63) 33.6 15.2

5J1420LH


Right hand shown,left hand opposite.

STANDARD DUTY END BITS



DOZER EDGES cont’d. - Inches (mm)

ENDS cont’d.


NOTE:Non dimensioned bolthole locations are on 3"or 6" centers.

10

END BIT DETAILS cont'd - Inches (mm)


4J8261RH& 15 (381) 9-9/16 (243) 12-5/16 (313) 8-1/16 (205) 1-3/4 (44) 13/16 (21) 3-1/2 (89) 4 (102) 4 (102) 2-1/2 (63) 25.8 11.7

4J8262LH

4T4455RH& 17-1/8 (435) 11-1/16 (281) 13-9/16 (344) 9-1/16 (230) 2-11/16 (68) 3/4 (19) 3-3/16 (81) 3-21/32 (93) 3-29/32 (99) 2-7/16 (62) 51.6 23.4

4T4454LH

9W1875RH& 18-1/2 (470) 11-7/8 (302) 14-5/8 (371) 9-3/4 (248) 2-7/8 (73) 3/4 (19) 3-3/16 (81) 3-21/32 (93) 3-29/32 (99) 2-7/16 (62) 60.5 27.4

9W1876LH



HEAVY DUTY RIBBED END BITS


Heavy duty ribbed end bit.Standard duty end bit.


8E4545RH& 32 (813) 19-9/16 (497) 26-5/16 (688) 16-3/8 (416) 6-11/16 (170) 2-1/16 (51) 2-31/32 (75) 9-1/4 (235) 7-9/16 (192) 4-17/64 (108) 382.0 173.3

8E4546LH



11

END BIT DETAILS cont'd. - Inches (mm)

END BITPART NO. A B C D E F G H I LBS. KGS.

4J8849RH& 19-1/8 (486) 11 (279) 16-1/4 (413) 10-3/8 (263) 2-7/16 (63) 1-1/8 (29) 4 (102) 3 (76) 3-1/4 (83) 53.0 24.0

4J8850LH

9J1479RH& 18-1/2 (470) 11-3/4 (298) 15-3/8 (390) 10 (254) 2-1/2 (63) 1-3/16 (30) 4 (102) 3 (76) 3-1/4 (83) 56.2 25.5

9J1480LH

9J1477RH& 19 (483) 11-7/8 (302) 15-7/8 (403) 10 (254) 2-9/16 (65) 1-3/16 (30) 4 (102) 3 (76) 3-1/4 (83) 59.0 26.8

9J1478LH

4J8843RH& 19 (483) 10-7/8 (276) 16-3/8 (416) 10-1/4 (260) 2-7/8 (73) 1-1/8 (29) 4 (102) 3 (76) 3-1/4 (83) 51.8 23.5

4J8844LH

3G8317HX& 20-13/16 (529) 11-5/8 (295) 16-1/4 (413) 10-1/4 (260) 2-1/8 (54) 1-3/16 (30) 4 (102) 3 (76) 3-1/4 (83) 61.0 27.7

3G8318HX

9W6199HRH& 19-3/8 (492) 12-3/8 (314) 16-3/4 (425) 10-3/8 (263) 3-5/16 (84) 1 (25) 4 (102) 3 (76) 3-1/4 (83) 80.0 36.3

9W6198HLH

3G8315HDR& 21-3/16 (538) 11-11/16 (297) 16-1/4 (413) 10-1/16 (256) 3-1/2 (89) 1-1/8 (29) 4 (102) 3 (76) 3-1/4 (83) 87.0 39.5

3G8316HDR

7T4091RH& 20-3/4 (527) 14 (356) 16-3/16 (411) 11-13/16 (300) 3-3/4 (95) 1-1/8 (29) 4 (102) 3 (76) 3-1/4 (83) 106.0 48.1

7T4090LH





Heavy duty ribbed end bit shown.Standard duty end bit

12

END BIT DETAILS cont'd. - Inches (mm)


1U1545HX& 26-13/16 (681) 14-1/2 (368) 21 (533) 12-1/2 (318) 3 (76) 1-9/16 (40) 2-15/16 (75) 7-1/8 (181) 3-15/16 (100) 143.0 64.9

1U1546HX

8E4541RH

& 29-7/16 (747) 18-19/32 (472) 22-3/4 (578) 16-1/8 (410) 6-1/4 (159) 1-15/16 (49) 3 (76) 7 (178) 3-15/16 (100) 275.0 124.7

8E4542LH

8E4541HDR& 29-1/4 (743) 18-3/4 (476) 22-3/4 (578) 12-1/8 (410) 6 (152) 1-7/8 (48) 3 (76) 7 (178) 3-15/16 (100) 285.0 129.3

8E4542HDR




Heavy duty extended wear life ribbed end bit.

Standard duty end bit shown.



8E4537HX& 24 (610) 15-3/8 (391) 18-3/8 (467) 11-1/2 (292) 4 (102) 2 (51) 4 (102) 3-1/4 (83) 3-5/16 (84) 134.0 60.8

8E4538HX

8E4539RH& 24-1/8 (613) 15-1/2 (394) 19 (483) 13 (330) 4-1/8 (105) 1-1/4 (32) 4 (102) 3-1/4 (83) 3-1/4 (83) 151.0 68.5

8E4540LH

7T4094RH& 26 (660) 18-3/4 (476) 18 (457) 14-1/4 (362) 5 (127) 3 (76) 4 (102) 3-1/4 (83) 3-1/4 (83) 236.0 107.0

7T4095LH




Heavy duty ribbed end bit.

13

REPLACEMENT RIPPER PARTS forDOZERS & LOADERSSEGMENTS • NOSES •SHANK GUARDS • RIPPER SHANKS

MACHINESHANK

ASSEMBLY†REPAIR

SEGMENTREPAIRNOSE

SHANK GUARDPART NO.

SHANK GUARDUPPER

FASTENER(S)

SHANK GUARDLOWER

FASTENER(S)

TOOTHSERIES1

D11 (SS) 8E0467, 8E1466 104-9279HX N/A 9N4621HX 8E2229P/101-2874W 8E2229P/101-2874W R5507T6020, 9W0259 (pin & retainer) (pin & retainer)

6Y2443P* 6Y2443P*

D11 (MS) 6Y3138, 8E8411 103-8115HX 107-3361HX 9W8365HX 6Y3909P/4T4707W 6Y3909P/4T4707W R500D10 6Y6141, 8E8414 (pin & retainer) (pin & retainer)D9L 6Y6144, 8E8415

6Y6147, 8E8416 3G0500P*8E8417, 109-9114

114-4503

6Y4679, 8E8412 103-8115HX 107-3361HX 6Y8960HX 6Y3909P/4T4707W 6Y3909P/4T4707W R500118-2140, 109-3135 6Y8960HHX (pin & retainer) (pin & retainer)

6Y5616, 8E84133G0500P*

1V4592, 7T5130 1U3630HX* 103-8114HX 6Y9704HX 8J48892 6Y3909P/4T4707W R5003G8566, 9W4427 (weld-on retainer) (pin & retainer)3G2088, 9W44269J5954, 1U4873

7T51313G0500P*

3G5707, 3G6507 1U3630HX* 103-8114HX 1U3644HX 6Y3909P/4T4707W R5001U3644HHX

3G0500P*

D9 107-3485, 107-3486 8E8418HX 9U9694HX 6J8814HX 6J8811P 6Y3394P/8E5559W R450D8 4T0134, 4T0135 6J8814WHX

4T0136, 4T8988 8E1848HX4T8989, 4T89907J1792, 7J17938E5339, 8E5340 7J1791HX* 4T9776WN* 6J8814HX 6J8811P 7J9600P* R4508E5341, 8E5345 6J8814WHX8E5346, 8E5347 8E1848HX8E5348, 9W6167

D7H 9W7382 9W7488WN R350983 7J6671

D7 D6 9J3139HX 9J3139SHX R350D5 (straight) 9J8920HX973 977 9J8923HX (old style)

(curved)

D4 941 9J6586HX C12WN R300951 955 (straight)963 9J89132

(curved)

953 943 1U12572 9J4254WN J250

D3 931 8J52992 8J7525WN J200

(SS)=Single Shank (MS)=Multi-Shank† Contact Hensley’s Attachment Division for Ripper Shank Replacements for D7H Dozers and larger.*Old Style Center Snap Ring Pin. See page 62 for details.1 See Tooth Series Application Chart on page 19.2 Reference only. Not available from Hensley Industries.

14

RIPPER WEAR PART DETAILS SORTED BY TOOTH SERIES - Inches (mm)

R550 SERIES

Shank Guard9N4621HX

wt.= 173.0 lbs. 78.5 kgs.

Weld-on Segment104-9279HX

wt.= 285.0 lbs. 129.3 kgs.

R500 SERIES


wt.= 96.0 lbs. 43.5 kgs.


wt.= 162.0 lbs. 73.5 kgs.

3-7/8(99)

23-7/8(607)

18(457)

13O

Weld-on Segment1U3630HX

(uses old style center snap ring pin)wt.= 224.0 lbs.101.6 kgs.


wt.= 98.0 lbs. 44.5 kgs.

Weld-on NoseC22WN

wt.= 46.9 lbs. 21.3 kgs.

Shank Guard9W8365HX

(3.62" Thick Shank)wt.= 84.0 lbs.38.1 kgs.

1-9/16 Dia.(40)

3-3/4(95)

1-9/16 x 2-3/16Slot (40x56)

6-5/8(168)

4-5/8(118)

16-5/8(422)

13-7/8(353)

4-1/4(108)

5-1/2(140)

REPLACEMENT RIPPER PARTSSEGMENTS • NOSES • SHANK GUARDS • RIPPER SHANKS

15

R500 SERIES - cont'd.

Shank Guard9W8365EXT

wt.= 94.0 lbs. 42.6 kgs.

Shank Guard6Y9704HX

wt.= 122.0 lbs. 53.3 kgs.

2-1/2(64)

1-1/2 x 2 Slot(38x51)

4-1/8(105)

19-1/16(484)25-1/2

(648)

5-5/8(143)

Shank Guard6Y8960HHX

wt.= 128.0 lbs. 58.1 kgs.

for DOZERS and LOADERSSEGMENTS • NOSES • SHANK GUARDS • RIPPER SHANKS

RIPPER WEAR PART DETAILS SORTED BY TOOTH SERIES cont'd. - Inches (mm)

1-9/16 Dia.(40)

1-9/16 x 3-3/16Slot (40x56)

6-5/8(168)

4-5/8(118)

16-5/8(422)

13-7/8(353)

4-1/8(105)

5-1/2(140)

Shank Guard6Y8960HX

(4.00" Thick Shank)wt.= 85.0 lbs. 38.5 kgs.

4-3/8(111)

4-1/8(105)

29(737)

5-1/4(133)

Shank Guard1U3644HX

wt.= 91.0 lbs. 41.3 kgs.

1-7/8 x 1-1/2 Slot(48x38)

9(229)

6-1/2(165)

29(737)

4-1/8(105)

Shank Guard1U3644HHX

wt.= 112.0 lbs. 55.3 kgs.

1-7/8 x1-1/2 Slot(48x38)

9-3/8(238)

16


R450 SERIES

Weld-on Segment9U9694HX

wt.= 43.5 lbs. 19.7 kgs.

14-1/4(362)

3(76)

38O

Weld-on Segment7J1791HX

(uses old stye center snap ring pin)wt.= 165.0 lbs. 74.8 kgs.

23-3/8(594)

3(76)

37O

Weld-on Segment8E8418HX

wt. = 150.0 lbs. 68.0 kgs.

23-1/16(586)

13-3/16(335)


Weld-on Segment4T9776WN

(uses old style center snap ring pin)

wt.= 36.8 lbs. 16.7 kgs.

Weld-on NoseC20WN

wt.= 24.5 lbs. 11.1 kgs.

Shank Guard6J8814WHX

wt.= 53.2 lbs. 24.1kgs.

3-1/8(80)

12-1/4(311)

1-3/8 Dia. (2 Holes)(35)

23-1/4(591)

4-1/4(108)

Shank Guard8E1848HX

wt.= 52.0 lbs. 23.6 kgs.

1-3/8 Dia.(35)

6-13/16(173)

12-1/4(311)

19-1/8(486)

5(127)

3-1/8(80)

3-1/4(83)

Shank Guard6J8814HX

wt.= 24.5 lbs. 11.1 kgs.

1-3/8 Dia. (2 Holes)(35)

3-1/16(78)

12-1/4(311)

4-1/4(108)

17(432)

17



R350 SERIES

Weld-on Segment9J3139SHX

wt.= 33.0 lbs. 15.0 kgs.

Weld-on Nose9W7488WN

wt.= 18.5 lbs. 8.4 kgs.

5-3/8(137)

3(76)

7-21/32(195)

Ripper Shank9J8923HX

wt.= 128.5 lbs. 58.3 kgs.

7 (178) 2-15/16(75)

2-1/16 Dia.(52)

20-1/2(521)

45O


wt.= 116.0 lbs. 52.6 kgs.

2-15/16(75)

20-5/8(524)

2-1/16 Dia.(52)

7 (178)

18



R300 SERIES

Weld-on Nose8J7525WN

wt.= 2.4 lbs. 1.1 kgs.

2-1/4(57)

2-5/16(59)

3-19/32(91)

Weld-on Nose9J4254WN

wt.= 5.1 lbs. 2.3 kgs.

3-1/4(83)

2-3/4(70)

4-1/2(114)

J250 SERIES

J200 SERIES

Weld-on NoseC12WN

wt.= 9.6 lbs. 4.4 kgs.

9J6586HX Ripper shankutilizes (1) 2K6413P pinwith (2) 3B5325P(3 X 15/32 cotter keys)also available from HensleyIndustries; see pages 62 - 63for pin detail.


wt.= 51.3 lbs. 23.3 kgs.

15(381)

5-1/2(140)

2-5/16(59)

1-7/8 Dia.(48)

19

RIPPER TOOTH TYPE


9W4551HX 1 17-5/8 (448) 3 (76) 8-3/8 (213) 4-9/16 (116) 9-7/16 (240) 88.5 40.1

9W4552HX 1 21-1/4 (540) 3 (76) 8-3/8 (213) 4-9/16 (116) 9-7/16 (240) 107.0 48.5

6Y3552HX 2 21-1/4 (540) 3-1/8 (80) 8-3/8 (213) 4-9/16 (116) 9-7/16 (240) 100.0 45.4

T9W4552 3 20 (508) 8-3/8 (213) 4-9/16 (116) 9-7/16 (240) 96.7 43.9

4T5501HX 2 14-3/4 (375) 2-3/4 (70) 6-1/2 (165) 4-1/4 (108) 7-1/2 (191) 53.5 24.3

4T5502HX 2 17-1/8 (435) 2-3/4 (70) 6-1/2 (165) 4-1/4 (108) 7-1/2 (191) 61.8 28.0

3G6503HX 2 18-3/4 (476) 2-3/4 (70) 6-1/2 (165) 4-1/4 (108) 7-1/2 (191) 63.0 28.6

4T4502HX 1 16-3/4 (425) 3 (76) 6-1/2 (165) 4-1/4 (108) 7-1/2 (190) 64.0 29.0

4T4503HX 1 19 (483) 2-7/8 (73) 6-1/2 (165) 4-1/4 (108) 7-1/2 (191) 68.0 30.8

3G6502HHX 1 17-1/4 (438) 3-3/4 (95) 6-1/2 (165) 4-1/4 (108) 7-1/2 (191) 77.2 35.0

T3G6502 3 16 (406) 6-1/2 (165) 4-1/4 (108) 7-1/2 (191) 49.8 22.6

T3G6503 3 18 (457) 6-1/2 (165) 4-1/4 (108) 7-1/2 (191) 49.8 22.6

3G6503CLAW 5 18 (457) 1-1/4 (32) 6-1/2 (165) 4-1/4 (108) 7-1/2 (191) 72.0 32.7

9W2451HX 1 12-7/8 (327) 3-1/8 (80) 4-7/8 (121) 3-3/8 (86) 6-1/2 (165) 38.2 17.3

4T4452HX 1 15-1/4 (387) 3-1/2 (89) 4-7/8 (124) 3-3/8 (86) 6-1/2 (165) 45.5 20.6

9W2452AHX 1 15-1/4 (387) 3-3/4 (86) 4-7/8 (121) 3-3/8 (86) 6-1/2 (165) 40.1 18.2

4T5451HX 2 12-7/8 (327) 2 (51) 4-7/8 (121) 3-3/8 (86) 6-1/2 (165) 37.7 17.1

4T5452HX 2 15-5/8 (397) 2 (51) 4-7/8 (121) 3-3/8 (86) 6-1/2 (165) 40.0 18.1

4T4452HX 1 15-1/4 (387) 3-1/2 (89) 4-7/8 (121) 3-3/8 (86) 6-1/2 (165) 45.5 20.6

4T4453HX 1 16-5/8 (422) 3-3/8 (86) 4-7/8 (121) 3-3/8 (86) 6-1/2 (165) 44.7 20.3

T6J8812 3 14-5/8 (372) 4-7/8 (124) 3-3/8 (86) 6-1/2 (165) 33.5 15.2

T9W2452 3 15 (381) 4-7/8 (124) 3-3/8 (86) 6-1/2 (165) 33.7 15.3

6Y0352HX 1 14 (356) 1-7/8 (48) 4-7/16 (113) 3-3/32 (78) 5-3/4 (146) 24.0 10.9

6Y0359HX 2 14 (356) 2-1/16 (52) 4-7/16 (113) 3-3/32 (78) 5-3/4 (146) 25.1 11.4

T6Y0352 3 15 (381) 4-7/16 (113) 3-3/32 (78) 5-3/4 (146) 24.3 11.0

6Y0309HX 2 11-3/8 (289) 1-3/4 (44) 3-1/4 (83) 2-1/4 (57) 4-7/16 (113) 11.4 5.2

T9J8910 3 11-3/4 (298) 3-1/4 (83) 2-1/4 (57) 4-7/16 (113) 12.0 5.4

9J8920HX 2 14-1/8 (359) 2-1/8 (54) 4-7/16 (113) 2-3/4 (70) 5-1/2 (140) 25.0 11.3

T9J8920 3 13 (330) 4-7/16 (113) 2-3/4 (70) 5-1/2 (140) 20.3 9.2

7J3310HX 4 12-1/8 (308) 4-15/16 (125) 3-29/32 (99) 3 (76) 6-3/4 (171) 23.4 10.6

7J3312HX 4 13-29/32 (353) 3-15/16 (100) 3-29/32 (99) 3 (76) 6-3/4 (171) 31.9 14.5

T7J3312 3 13 (330) 3-29/32 (99) 3 (76) 6-3/4 (171) 22.5 10.2

WEIGHTDIMENSIONS - Inches (mm)TOOTH

SERIES

FASTENERS

8E2229P/1012874W

or6Y2443P*

R550

R5006Y3909P/4T4707W

or3G0500P*

R450

6Y3394P/8E5559W

or7J9600P*

R3509W2678P/6Y9459W

R300

Old

Style


TOOTH OPTIONS

TYPE 3 (TIGER)

E

C

A

B

A

C

D

E

TYPE 1 (CENTERLINE) TYPE 2 (NON-CENTERLINE)

E

D

A

C

DB

E

TYPE 4

B

A

D

C

TYPE 5 (NON-CENTERLINE)

5J9000P

9J2358P/6Y9459W

*Old Style Center Snap Ring Pin

9J6583P/6Y9459W

(see pages 62 - 63)

20

REPLACEMENT RIPPER PARTS forMOTORGRADERSRIPPER SHANKS • WELD-ON NOSES • TEETH • PINS & WASHERS

*Reference only. Not available from Hensley Industries.** Weld on nose is utilized only with the R350 series teeth shown above.

MACHINE WELD-ON TEETH (See Below) FASTENERSMODEL NOSE OR CENTERLINE PENETRATOR TIGER PIN WASHER

SHANK

12G 9J6586HX14G (Straight)120 6Y0309HX T9J8910HX 9J6583P 6Y9459W130 * 9J8913140 (Curved)

C12WN(Nose)

9J3139HX(Straight)

9J8923HX 6Y0359HX T6Y0352HX16G (Curved)

or or

9J3139SHX 6Y0352HX 9J8920HX T9J8920HX 9W2678P 6Y9459W(Segment)

** 9W7488WN(Nose)

(See Page 62 - 63)

9W7488WNwt.= 18.5 lbs. 8.4 kgs.

RIPPER TOOTH TYPE


6Y0309HX 2 11-7/16 (290) 1-3/4 (44) 3-1/4 (83) 2-1/4 (57) 4-3/8 (111) 11.4 5.2

T9J8910 3 11-3/4 (298) 3-1/4 (83) 2-1/4 (57) 4-3/8 (111) 12.0 5.4

9J8920HX 2 14-1/8 (359) 2-1/8 (54) 4-7/16 (113) 2-3/4 (70) 5-1/2 (140) 25.0 11.3

T9J8920 3 13 (330) 4-7/16 (113) 2-3/4 (70) 5-1/2 (140) 20.3 9.2

6Y0352HX 1 14 (356) 1-7/8 (48) 4-7/16 (113) 3-3/32 (78) 5-3/4 (146) 24.0 10.9

T6Y0352 3 15 (381) 4-7/16 (113) 3-3/32 (78) 5-3/4 (146) 24.3 11.0

6Y0359HX 2 14 (356) 2-1/16 (52) 4-7/16 (113) 3-3/32 (78) 5-3/4 (146) 25.1 11.4

TYPE 1(CENTERLINE)

TYPE 3(TIGER)

TYPE 2(NON-CENTERLINE)


B D

E

C

A A

C

E

DB

A

C

E

D

9J8923HXwt.= 128.5 lbs. 58.3 kgs.

9J3139HXwt.= 116.0 lbs. 52.6 kgs.

9J6586HXwt.= 51.3 lbs. 23.3 kgs.

15(381)

2-15/16(75)

20-5/8(524)

7 (178)2-15/16

(75)2-5/16(59)

9J6586HX ripper shank utilizes (1)2K6413P pin with (2) 3B5325P

(3 X 15/32 cotter keys) also availablefrom Hensley Industries;

see page 62 - 63 for pin detail.

2-1/16 Dia.(52)

20-1/2(521)

2-1/16 Dia.(52)

5-1/2(140)

1-7/8 Dia.(48)

7 (178)

45O

5-3/8(137)

3(76)

7-21/32(195)

3(76)9-1/4 (235)

9J3139SHXwt.= 33.0 lbs. 15.0 kgs.

10 (254)

21

UNIVERSAL STRAIGHT V-BLOCK V-BLOCK(Front and BLOCK (Front Notch) (Front and

Rear Notches) (Rear Notch) Rear Notches)

Scarifier Shank 101HX 5B6251HX 9F5124HX 101HX

Tip, Standard 5B946HX 5B946HX 5B946HX 5B946HX

Tip, Heavy Duty 2D5572HX* 2D5572HX* 2D5572HX* 2D5572HX*

Tip, Wide T2D5572 T2D5572 T2D5572 T2D5572

Tip, Heavy Duty 6Y5230HX 6Y5230HX 6Y5230HX 6Y5230HX

SHANK TYPEPART NO. A B C D E F G H J K L M N LBS. KGS.

5B6251HX 1 2-1/2 15-1/8 1 3/4 3/4 3/4 3/4 10.7 4.8(64) (384) (25) (19) (19) (19) (19)

9F5124HX 2 3 17-1/4 1 13/16 13/16 13/16 13/16 13/16 13/16 13.4 6.1(76) (438) (25) (21) (21) (21) (21) (21) (21)

101HX 3 3 17-1/4 1 3/4 11/16 3/4 11/16 1-1/8 13/16 1-1/4 13/16 13.5 6.1(76) (438) (25) (19) (18) (19) (18) (29) (21) (32) (21)

104HXL 3 3 20 1 9/16 13/16 11/16 13/16 1-1/4 13/16 1-5/16 13/16 16.0 7.3(76) (508) (25) (14) (21) (18) (21) (32) (21) (33) (21)

*Replaced by 6Y5230HXNOTE: All scarifier shanks utilize 1D3537HX or 5K1459W wedge pins.

11/16(17)

5K1459Pwt.= 1.0 lbs. 0.4 kgs.

TIP TYPE

PART NO. A B LBS. KGS.

5B946HX 1 6-1/2 (165) 1-9/16 (40) 2.1 .9

T2D5572 2 7-1/2 (191) 3 (76) 3.2 1.5

6Y5230HX 1 7-1/4 (184) 1-13/16 (46) 3.2 1.5

4-1/2(114)

1(25)

2(51)

A

DEFG

C A C CA

HJKLMN

TYPE 1 TYPE 2 TYPE 3

B

A

B

A

TYPE 1 TYPE 2

BB B

DEFG

HJKL

REPLACEMENT SCARIFIER PARTS forMOTORGRADERSSCARIFIER TIPS • SHANKS

WEIGHT

WEIGHT

1D3537HXwt.= 2.0 lbs. 0.9 kgs.



8-1/16(205)

1-1/4(32)

1(25)

11/16(17)

22

A B

CD

GO

ADAPTER CAT TOOTH WT.PART NO. SERIES A B C D G LBS. (KGS) SIZE ASSY. NO. QTY.

9J8455HX J250 5-3/16 (132) 3 (76) 1-11/16 (43) 15/16 (24) 16O 14.1 (6.4) 3/4 X 3-3/4 A34-334 2

9J2307HX J300 6-3/4 (171) 3 (76) 2 (51) 15/16 (24) 13O 25.7 (11.7) 1 X 4-1/2 A10-412 2

9W9971HX J350 7 (178) 3 (76) 2-9/16 (65) 1-1/2 (38) 5O 31.9 (14.5) 1 X 5-1/2 A10-512 2

MACHINE STANDARD **OPTIONALMODEL ADAPTER TOOTH TEETH PIN WASHER

613 9J8455HX 1U3252HX J250 Series 9J2258P 3G9609W

615 4T5805* 1U3302HX J300 Series 9J2308P 3G9609W

J619J621 9J2307HX 1U3302HX J300 Series 9J2308P 3G9609W623

633 9W9971HX 1U3352HX J350 Series 9J2358P 6Y9459W639

TEETH FASTENERS

(See Page 62 - 63)

TEETH • ADAPTERS • PINS & WASHERS

REPLACEMENT PARTS

*Reference only. Not available from Hensley Industries.** See " TOOTH SERIES REFERENCE CHART" pages 50 - 51 for teeth styles & additional information.

DIMENSIONS - Inches (mm) *PLOW BOLTS

*see page 78 for assembly details

23

MACHINE ROUTER BITMODEL LEFT RIGHT

615 4J8665H (Standard)621 7J3023HX (Heavy Duty) 8J7211HX 8J7210HX623

615 - 666 4J8665H (Standard)

619 - 666 7J3023HX (Heavy Duty)

D

G FG

F1-3/32 Dia.(28) Typ.

BHO

A

E

C

8-1/2(216)

10-1/16(256)

8J7210HX (RH Shown)8J7211HX (LH Opposite)wt.= 17.7 lbs 8.0 kgs. ea.

BOLT-ON GUIDES

ROUTER BITS

1-1/4 (32)2-1/4 (57)

GUIDES • ROUTER BITS

ROUTER BITPART NO. A B C D E F G H LBS. KGS.

4J8665H 21-1/8 (537) 8-5/8 (219) 3/4 (19) 4-1/4 (108) 10-1/2 (267) 3-1/2 (89) 2-1/2 (64) 8O 52.5 23.8

7J3023H 22-3/4 (578) 9-5/8 (244) 7/8 (22) 4-13/16 (122) 11-3/8 (289) 3-1/2 (89) 2-1/2 (64) 12O 78.3 35.5


BOLT-ON GUIDE

for SCRAPERS

24

BOX RIPPER SYSTEMS

REPLACEMENT NOSES

FEATURES INCLUDE:• High quality alloy steel castings for both box and

ripper shank

• Re-engineered tighter fit between box and shank

• New stronger, reusable box pin to reduce shankmovement

• Second box pin location to further eliminateshank movement

• Three pin hole locations in shank to cover greaterrange of bucket profiles and ripping depths

• Uses Caterpillar® style ripper teeth

Kit BK200 BK250 BK300 BK350-1 BK350-2 BK400

Shank C200-12 C250-14 C300-20 C350-20 C350-22 C400-22

Box Pin B250P (2) B250P (2) B250P (2) B350P (2) B350P (2) B350P (2)

9J6583P 9W2678P 6Y3394P 6Y3394P 6Y3909P 6Y3909P6Y9459W 6Y9459W 8E5559W 8E5559W 4T4707W 4T4767W

Box B200 B250 B300 B350 B350 B400

System

200 250 300 350 350 400

T9J8910 T6Y0352 T9W2452 T9W2452 T366503 T366503(R300) (R350) (R450) (R450) (R500) (R500)

ToothFastener*

TigerTooth

(tooth series)

SYSTEM COMPONENTS

B200 215, 311, 312, 315 20,000 - 39,000 lbs.(9,072 - 17,690 kgs.)

B250 225, 320, 322 40,000 - 59,000 lbs.(18,144 - 26,762 kgs.)

B300 325, 330 60,000 - 84,000 lbs.(27,216 - 38,102 kgs.

B350 235C 85,000 - 109,000 lbs.(38,556 - 49,442 kgs.)

B400 350L, 245, 345 110,000 - 169,000 lbs.(49,896 - 76,658 kgs.)

APPLICATIONS

COMPLETEBOX RIPPER SYSTEM

A B C LBS. KGS.

C12WN C200-12 3 (76) 4-1/4 (108) 5-23/32 (145) 9.6 4.4

9W7488WN C250-14 3 (76) 5-3/8 (137) 7-21/32 (194) 18.5 8.4

C20WN C300-20 2-15/16 (75) 6 (152) 8-13/16 (224) 24.5 11.0C350-20

C22WN C350-22 3-29/32 (99) 7-5/8 (194) 10-1/4 (260) 46.9 21.0C400-22

DIMENSIONS - Inches (mm) WEIGHTWELD-ONNOSE

FORSHANK No.

SYSTEM MACHINE MODELMACHINE

OPERATING WEIGHT

*see page 62 & 63 for fastener details

BOX PINS

B250Pwt.= 2.7 lbs. 1.2 kgs.

B350Pwt.= 5.6 lbs. 2.5 kgs.

25

RIPPER SHANKS

RIPPER BOXES

BOX A B C D E F G LBS. KGS.

B200 6 (152) 2-1/2 (63) 14-7/8 (378) 11-7/8 (302) 8-9/16 (218) 6-13/16 (173) 10-1/2 (267) 55.0 24.9

B250 6 (152) 2-5/8 (67) 17-1/8 (435) 13-5/8 (346) 9-3/4 (248) 7-13/16 (198) 12 (305) 75.0 34.0

B300 6 (152) 3-1/8 (79) 19-1/8 (486) 15-5/16 (389) 11-3/16 (284) 8-3/4 (222) 13-1/2 (343) 105.0 47.6

B350 7-1/2 (191) 4 (102) 21-1/4 (540) 17 (432) 12-1/4 (311) 9-3/4 (248) 15 (381) 150.0 68.0

B400 7-15/16 (202) 5-1/4 (133) 25-1/2 (648) 20-7/16 (519) 14-3/4 (375) 11-3/4 (298) 18 (457) 245.0 111.1


BOX SHANK A B C D E LBS. KGS.

B200 C200-12 31-3/16 (792) 8 (203) 4-13/16 (122) 3-1/2 (89) 2 (51) 65.0 29.5

B250 C250-14 36-3/4 (933) 10-1/8 (257) 5-1/2 (140) 4 (102) 2-1/2 (64) 95.0 43.1

B300 C300-20 41 (1041) 11-1/4 (286) 6-3/16 (157) 4-1/2 (114) 3 (76) 113.0 51.3

C350-20 45 (1143) 11-1/8 (283) 6-7/8 (175) 5 (127) 3-1/8 (79) 185.0 83.9B350

C350-22 46 (1168) 12-3/4 (324) 6-7/8 (175) 5 (127) 3-1/8 (79) 200.0 90.7

B400 C400-22 54 (1372) 13-3/4 (349) 8-1/4 (210) 6 (152) 3-3/4 (95) 300.0 136.1


FOR EXCAVATORS

26

REPLACEMENT PARTS for BACKHOES &EXCAVATORS

MACHINEMODEL STICK BUCKET CENTER LEFT-HAND RIGHT-HAND

D3, 8J7525HX416, 426 General Purpose J200 (Bottom Leg)428, 436 119-3204HX

(Wrap Around)

446, E70B J225 6Y3224HX

E110B, 120B General Purpose J250 6Y3254HX

General Purpose J300 9W1304HXE180B, E220

Heavy Duty Rock J350 6I6354HX *6I6356 *6I6355

205, 206, General Purpose J250 3G0169HX211, 212,213, 214 Heavy Duty Rock J300 *9J8929

213B, 214B General Purpose/ Rock J300 *9J8929

General Purpose J300 3G6304HXC 3G6306HXL 3G6305HXR215, 219

Heavy Duty Rock J350 3G8354HXC 3G8356HXL 3G8355HXR

224 General Purpose J300 *9J8929

Backhoe & Mass Excavating J350 3G8354HXC 3G8356HXL 3G8355HXR225

Heavy Duty Rock J450 8J9141HXC 8J9140HXL 8J9139HXR

227,229 Backhoe & Mass Excavating J350 3G8354HXC 3G8356HXL 3G8355HXR

J450 8J9141HXC 8J9140HXL 8J9139HXRBackhoe & Mass Excavating

235 J460 8E6464HXC 8E6466HXL 8E6465HXR

Heavy Duty Rock J550

E240, EL240 J350 6I6354HX *6I6356 *6I6355

Backhoe & Mass Excavating 9J0174HXC 9J0173HXL 9J0172HXR245 J550

Front Shovel 3G9494HXC 3G9496HXL 3G9495HXR

311, 312 General Purpose J250 6Y3254HX

6'-3" - Short 35T, 36T, 39T, 42T J300 8E9490HX44X, 47X, 50X, 54X

318, 320, 320L 9'-7", 8'-2" - Std.24ET, 30ET, J350 6I6354HX *6I6356 *6I6355

12'-8" - Long 43EX, 44ET

320ME 6'-3", 7'-10" - Short 30ET, 32ET, 37ET, 47EX, 54EX J400 7T3404HXC *6I6406 *6I6405

13'-3" - Long J300 8E9490HX

322L, 325, 325L 8'-8",10'-6" - Std. 31T, 36T, 42T, 48T, J350 6I6354HX *6I6356 *6I635553X, 54X, 54T, 57MX

6'-7", 8'-3" - Short 30ET, 36ET, 51EX, 57EMX J460 8E6464HXC 8E6466HXL 8E6465HXR

31T, 36T, 42T, 48T, J350 6I6354HX *6I6356 *6I635553X, 54X, 54T, 57MX

15'-9" - Long30ET, 32ET, 37ET, J400 7T3404HXC *6I6406 *6I6405

46EX, 54EMX

42T, 48T, 54T, 56X, J400 7T3404HXC *6I6406 *6I64059'-2" - Std. 59X, 60MX

330, 330L 10'-10" - Std.11'-6" - Std. 30ET, 36ET, 51EX, 57EMX 8E6464HXC 8E6466HXL 8E6455HXR

12'-10" - Std.35R J460

63X, 68MX 8E6464HXC 8E6466HXL 8E6455HXR8'-4" - Short

59EX, 64EMX J550 6I6554HXC 6I6556HXL 6I6555HXR

J460 8E6464HXC 8E6466HXL 8E6465HXR

350, 350LJ550 6I6554HXC 6I6556HXL 6I6555HXR

54T, 60T, 71X J550 6I6554HXC 6I6556HXL 6I6555HXR14'-5", 18'-1" - Long

42ET, 48ET

375, 375L 60T, 66T, 80X, 87X, 94MX 6I6604HXC *6I6606 *6I66059'-7" - Std. J60011'-2" - Std13'-5" - Std. 81V, 88VMX

*Reference only. Not available from Hensley Industries.** See "TOOTH SERIES REFERENCE CHART" pages 50 - 51 for teeth styles & additional information.

EXCAVATOR SPECIFICATIONS TOOTHSERIES**

ADAPTERS(See Pages 60 - 69)

27

ADAPTERS • TEETH • PINS & WASHERS • SIDECUTTERS

†see page 78 for plow bolt details

MACHINERIGHT- HAND LEFT-HAND PLOW BOLT ASSY.† PLATE PLOW BOLT ASSY.† MODEL

D3,8J7525WN 416,426,

428, 436

6Y3224WN 446, E70B

9J4254WN E110B, 120B

9J4304WN9J1855HXR 9J1856HXL A34-212 (3) E180B, E220

9J4354WN

9J4254WN 205, 206,211, 212,

9J4304WN 213, 214

9J4304WN 213B, 214B

9J4304WN9J1855HXR 9J1856HXL A34-212 (3) 215, 219

9J4354WN

9J4304WN 224

9J4354WN8J9615HXR 8J9614HXL A10-300 (3) 4T2886BHX A34-314 (4) 225

3G4454WN

9J4354WN 227, 229

3G4454WN

8E6464WN 8J9615HXR 8J9614HXL A10-300 (3) 4T2886BHX A34-314 (4) 235

9J4354WN 8J9615HXR 8J9614HXL A10-300 (3) 4T2886BHX A34-314 (4) E240, EL240

9J4554WN 8J9825HXR 8J9826HXL A10-312 (5) 4T6664PHX A34-314 (4) 245

9J4254WN 311, 312

9J4304WN

318, 320, 320L9J4354WN 8J9615HXR 8J9614HXL A10-300 (3) 4T2886BHX A34-314 (4)

7T3404WN 8J9615HXR 8J9614HXL A10-300 (3) 4T2886BHX A34-314 (4) 320ME

9J4304WN

9J4354WN 8J9615HXR 8J9614HXL A10-300 (3) 4T2886BHX A34-314 (4) 322L, 325,325L

8E6464WN

9J4354WN

7T3404WN 8J9615HXR 8J9614HXL A10-300 (3) 4T2886BHX A34-314 (4)

7T3404WN

330, 330L

8E6464WN8J9825HXR 8J9826HXL A10-312 (5) 4T6664PHX A34-314 (4)

9J4554WN

8E6464WN

8J9825HXR 8J9826HXL A10-312 (5) 4T6664PHX A34-314 (4) 350, 350L9J4554WN

9J4554WN

6I6604WN 8J9825HXR 8J9826HXL A10-312 (5) 4T6664PHX A34-314 (4) 375, 375L

WELD-ONNOSE

SIDECUTTERS (See Pages 70 - 72)

BLADE-TYPE SIDECUTTERS COMBINATION PLATE

28

1-1/2 & 2-LEG WELD-ON ADAPTERS(See Page 66 - 67)

FLUSH MOUNT WELD-ON ADAPTERS(See Page 65)

REPLACEMENT PARTS for LOADERS withWELD-ON ADAPTER SYSTEMS

4T7555R/LHX

(See pages 50-51)

*Reference only. Not available from Hensley Industries. **See "TOOTH SERIES REFERENCE CHART" pages 50 - 51 for teeth styles & addtional information.***Older J450 adapters and fasteners available.

TOOTHSERIES**MACHINE CENTER CENTER

MODEL (STRAIGHT) RIGHT-HAND LEFT-HAND (STRAIGHT) RIGHT-HAND LEFT-HAND

936, 938F, J250 1U1254HXC941, 943

950, 950B, E, F J300 1U1304HXC

950B, E, F, G J350 1U1354HXC 1U1355HXR 1U1356HXL

951, 953 J250 1U1254HX

960F, 962G J350

963 J300 1U1304HXC

963B J350 1U1354HXC

966, 966C, J350D, E, F

966G J350 135-9354* 135-9355HXR* 135-9356HXL*

972G J350 135-9354* 135-9355* 135-9356*

973 J350 135-9354* 135-9355* 135-9356* 1U1354HXC 1U1355HXR 1U1356HXL

977 J350 1U1354HXC

980, 980B, J350 1U1354HXC 1U1355HXR 1U1356HXLC, F

980F, G J400 125-8404HXC 125-8405HXR 125-8406HXL 107-3404HX

980G J460 8E3464HXC 8E3465HXR 8E3466HXL

983 J460 8E3464HXC 8E0464HXC

988, 988B J460*** 8E3464HXC 8E3465HXR 8E3466HXL 8E0464HXC 8E0465HXR 8E0466HXL

988F J460 8E3464HXC 8E3465HXR 8E3466HXL 8E0464HXC 8E0465HXR 8E0466HXL

988F J550 4T7554CHX

988G, 990 J550 107-3554HX 107-3555HX 107-3556HX 3G4554HXC 3G4555HXR 3G4556HXL

112-2554HX 112-2555HX 112-2556HX(w/tungsten carbide) (w/tungsten carbide) (w/tungsten carbide)

992, 992B, J550 107-3554HX 107-3555HX 107-3556HX 3G4554HXC 3G4555HXR 3G4556HXLC, D, G


992G J600 119-8604HX 119-8605HX 119-8606HX


992G J700 4T4704HXC 4T4705HXR 4T4706HXL

29

WELD-ON ADAPTERS • TEETH • PINS & WASHERSWELD-ON NOSES

BOTTOM LEGWELD-ON

ADAPTERS

BOLT-ON SEGMENTS(See Page 38 - 40)

BOLT-ONHEEL PLATE

† Replaces 9W5734NRHX, 9W5737NRHX, 9W5730NRHX

CENTER CENTER(STRAIGHT) RIGHT-HAND LEFT-HAND (STRAIGHT) RIGHT-HAND LEFT-HAND

3G0169HX 132-1037NRHX4T6694NRHX4T6692NRHX

4T6691*

9J8929* 4T6693NRHX 9W6747HX4T6694NRHX

132-1037NRHX

1U1350CHX 4T3015NRHX 4T9123NRHX 4T9124NRHX 9W6747HX1U1351R/LHX

3G0169HX 4T6692NRHX4T6694NRHX

1U1350CHX 132-4715* 9W6747HX1U1351R/LHX

9W6748HX

9W6748HX

1U1350CHX 4T6697NRHX 4T9123NRHX 4T9124NRHX 9W6749HX1U1351R/LHX

135-9544* 135-9545* 135-9546* 161-8573*

135-9544* 135-9545* 135-9546* 161-8573*

1U1350CHX 7V0910HX1U1351R/LHX 9W6750*

1U1350CHX

1U1350CHX 4T3015NRHX 4T7139NRHX 4T7140NRHX 7V0910HX1U1351R/LHX 9W6750*

116-7460CHX† 116-7461RHX † 116-7462LHX†

116-7460CHX† 116-7461RHX† 116-7462LHX † 109-9215HX

116-7460CHX† 116-7461RHX† 116-7462LHX† 6Y3609HX

109-9080NRHX 109-9081NRHX 109-98082NRHX 6Y3609HX

116-7460CHX† 116-7461RHX† 116-7462LHX† 6Y3609HX

4T6760NRHX 4T6761NRHX 4T6762NRHX 195-7096HX 195-7097HX 195-7098HX 6Y3573HX (990 only)(2-3/8") (2-3/8") (2-3/8")

4T6760NRH-HX 4T6761NRH-HX 4T6762NRH-HX(2-3/8") (2-3/8") (2-3/8")

4T6760NRHX 4T6761NRHX 4T6762NRHX 195-7096HX 195-7097HX 195-7098HX 6Y3610HX(2-3/8") (2-3/8") (2-3/8")

4T6760NRH-HX 4T6761NRH-HX 4T6762NRH-HX(2-3/8") (2-3/8") (2-3/8")

109-2675NRHX 109-2676NRHX 109-2677NRHX(3-1/4") (3-1/4") (3-1/4")

4T6760NRHX 4T6761NRHX 4T6762NRHX 195-7096HX 195-7097HX 195-7098HX 115-1548*(2-3/8") (2-3/8") (2-3/8")

4T6760NRH-HX 4T6761NRH-HX 4T6762NRH-HX 115-1549*(2-3/8") (2-3/8") (2-3/8")

109-2675NRHX 109-2676NRHX 109-2677NRHX(3-1/4") (3-1/4") (3-1/4")

4T6760NRHX 4T6761NRHX 4T6762NRHX 195-7096HX 195-7097HX 195-7098HX 115-1548*(2-3/8") (2-3/8") (2-3/8")

4T6760NRH-HX 4T6761NRH-HX 4T6762NRH-HX 115-1549*(2-3/8") (2-3/8") (2-3/8")

109-2675NRHX 109-2676NRHX 109-2677NRHX(3-1/4") (3-1/4") (3-1/4")

TOP COVER PLATES(See Page 41)

(See Pages 68 - 69) (See Pages 42 - 43)

30

REPLACEMENT PARTS for LOADERS withBOLT-ON ADAPTER SYSTEMS

*Reference only. Not available from Hensley Industries.** See " TOOTH SERIES REFERENCE CHART" pages 50 - 51 for teeth styles & additional information.

***Specific segment is based on width of bucket.

(See Page 42 - 43)

BOLT-ON ADAPTERS(See Pages 63 - 64)

416, 426, 428, J200 9W6207HX436, 438

446 J225 6Y3224HX(weld-on)

910, 914 J200 9J4207HX 5G2806* 5G2807* 128-2873*128-2872*

IT12, IT14, J250 1U257HX 3G4258HX 3G4259HX 132-1037NRHXIT24F, IT26 (1 hole) (1 hole)IT28, IT38 6I9250* 6I9251* 8E4569*

(2 hole) (2 hole)

916, 918F, J250 1U257HX 3G4258HX 3G4259HX 4T6694NRHX920, 924F, (1 hole) (1 hole) 4T6693NRHX

926, 928, 930 6I9250* 6I9251* 8E4569*(2 hole) (2 hole)

931, 933, J200 9J4207HX 1U2208* 1U2209*935

J225 6Y6227* 6Y6228* 6Y6229* 6Y6362*

936, 938F/G, J250 1U257HX 3G4258HX 3G4259HX 132-1037NRHX939, 941, (1 hole) (1 hole) 4T6692NRHX943, 951, 8E9250* 8E9251* 4T6691*

953, 953B/C (2 hole) (2 hole)

953B/C, J300 1U307HX 3G4308HX 3G4309HX 4T6694NRHX955 1 hole) (1 hole)

8E5308* 8E5309*(2 hole) (2 hole)

955 J300 4T4307HX 3G4308HX 3G4309HX(1 hole) (1 hole)

8E5308* 8E5309*(2 hole) (2 hole)

944, 950 J300 1U0307HX 3G4308HX 3G4309HX 4T6693NRHX 9W6747HX(1 hole) (1 hole) 4T6694NRHX

8E5308* 8E5309* 132-1037NRHX(2 hole) (2 hole)

950B, E, J300 4T4307HX 3G4308HX 3G4309HX 132-1037NRHX 9W6747HXF, G (1 hole) (1 hole) 132-4715*

8E5308* 8E5309*(2 hole) (2 hole)

960F J350 3G3357HX 3G5358HX 3G5359HX 9W6747HX(1 hole) (1 hole)8E5359 8E5358(2 hole) (2 hole)

960F J300 4T4307HX 8E5308* 8E5309* 9W6747HX

962G, 963, J300 4T4307HX 8E5308* 8E5309* 4T6693NRHX 9W6747HX963B 4T6694NRHX (962)

132-4715* 9W6748HX(963)

963B J350 3G7357HX 3G5358HX 3G5359HX 4T6696NRHX 9W6748HX(1 hole) (1 hole) 4T6697NRHX8E5359 8E5358(2 hole) (2 hole)

966C J300 8J5307HX

966C J300 3G9307HX 3G8308HX 3G8309HX(1 hole) (1 hole)

MACHINEMODEL CENTER LEFT-HAND

CORNERRIGHT-HAND

CORNER

BOLT-ON SEGMENTS(See Pages 38 - 40)

***STRAIGHTLIP

BOLT-ONHEEL PLATETOOTH

SERIES**

31

BOLT-ON ADAPTERS • TEETH • PINS & WASHERSBOLT-ON SEGMENTS • HEEL PLATES

(See Page 42 - 43)

BOLT-ON ADAPTERS(See Pages 63 - 64)

966C J350 3G3357HX 3G5358HX 3G5359HX(1 hole) (1 hole)

8E5358* 8E5359*(2 hole) (2 hole)

966D, E, F, G J350 3G3357HX 3G5358HX 3G5359HX 4T6698NRHX 9W6749970, 970F, (1 hole) (1 hole) 4T6699NRHX

972G 8E5358* 8E5359* 100-6666NRHX(2 hole) (2 hole)

973, 977 J350 3G3357HX 3G5358HX 3G5359HX 4T6696NRHX 7V0910HX(1 hole) (1 hole) 9W6750*

8E5358* 8E5359*(2 hole) (2 hole)

980, 980B, C J350 3G2357HX

980C, F J350 3G1357HX 1U1358HX 1U1359HX 4T6700NRHX 7V0910HX4T6700HX 9V6109*(reversible) 9W6750*

980F, G J400 6I9898HX 6I8244* 6I8243* 109-9019NRHX 109-9215HX

MACHINEMODEL CENTER LEFT-HAND

CORNERRIGHT-HAND

CORNER

BOLT-ON SEGMENTS(See Pages 38 - 40)

***STRAIGHTLIP

BOLT-ONHEEL PLATETOOTH

SERIES**

*Reference only. Not available from Hensley Industries.** See TOOTH SERIES REFERENCE CHART" pages 50 - 51 for teeth styles & additional information.

***Specific segment is based on width of bucket.

32

REPLACEMENT MODULOK PARTSfor LOADERS

• Vertical Protectors - Pinned-on to protect bucket cheek plate from wear.Interchangeable from cheek to cheek.

• Flush Mounted Adapters - Welded in place to provide asturdy base for replaceable teeth, adapter covers, and edge segments.These adapters provide a smooth, flat working surface, reducing tirecosts, and allowing faster clean-up. Available in standard & heavyversions.

• Adapter Covers - Protect adapter, reducing the need for adapterreplacement. Covers are side-pinned, allowing for quick changes.

• Teeth - Standard heavy teeth or "RP2" style teeth available.

• Cutting Edge Segments - Protect the leading edge of thesupport assembly. Bucket life is extended, and penetration improved.Edges wrap under support to protect bucket bottom. Available instandard & heavy versions.

LIP WIDTH RIGHT LEFT RIGHT LEFTMODEL Inches (mm) CENTER CORNER CENTER HAND HAND CENTER HAND HAND

132 8J6396HX 8J6397HX988A (3353) or or 8J8313HX 8J8222HX 8J8223HX 8J6398HX 9U9334RHX 9U9333LHX

8E1464HXC 8E1465HX (1) (3) (3) (8) (3) (3)(6) (2)

988B 143.5 8J6396HX 8J6397HX(3645) or or 9J4429HX 8J8222HX 8J8223HX 8J6398HX 9U9332CHX 9U9334RHX 9U9333LHX

8E1464HXC 8E1465HX (2) (3) (3) (9) (2) (3) (3)(7) (2)

988F 143.0 8E1464HXC 8E1465HX 9U9664CHX 9U9334RHX 9U9333LHX(3623) (7) (2) (2) (3) (3)

990 167.7 1U1554HX 1U1554HX 8E9514HX 102-9680RHX 102-9681LHX(4260) (6) (2) (1) (3) (3)

992 181.0 1U1554HX 1U1554HX 8J3962HX 9J9973HX 9J9974HX 1U0741HX *8E9564 *8E9565 *8E9566(4597) (7) (2) (2) (3) (3) (9) (2) (3) (3)

107-5894* 8E9515HXR 8E9516HXL(2) (3) (3)

992 187.0 1U1554HX 1U1554HX 1U0869HX 9J9973HX 9J9974HX 1U0741HX 8E9514HX 8E9515HXR 8E9516HXL(4750) (7) (2) (2) (3) (3) (9) (2) (3) (3)

992G 187.0 119-9604HX 119-9605HX 133-0730* 133-0731* 133-0732* CENTER(HD (4750) (6) (2) 133-0734HX

MINING (6)SYSTEM) CORNER

133-0735HX(2)

(See Page 36)(See Page 35)

(See Page 34)

(See Page 36)

NOTE - For 988 Modulok teeth fasteners, different size pins & washers are to be used based on pin hole size in adapter.* Reference only. Not available from Hensley Industries.

STANDARD EDGE SEGMENTSADAPTERS HD EDGE SEGMENTSMACHINE STANDARDADAPTER

COVER

33

TOOTH

FLUSH MOUNTADAPTER

ADAPTERCOVER

CUTTING EDGESEGMENT

(See pages 34 - 36 for all Modulok details.)

VERTICALPROTECTOR

PROTECTORPIN WASHER PART NO. PIN WASHER HD RP-2 PIN WASHER

9U9331HX 6Y2527P 6Y9459W 8J6399HX 9J8442P 6Y9459W 9N4452HX 9W1453RP2 6Y2527P (8) 6Y9459W (8) (8) (8) (8) (2) (4) (4) (8) (8) or or

8E0468P (8) 8E0469W (8)

9U9331HX 6Y2527P 6Y9459W 9J9600HX 9J8442P 6Y9459W 9N4452HX 9W1453RP2 6Y2527P (9) 6Y9459W (9)(9) (9) (9) (2) (4) (4) (9) (9) or or

8E0468P (9) 8E0469W (9)

9U9331HX 6Y2527P 6Y9459W 9J9600HX 9J8442P 6Y9459W 9N4552HX 9W1453RP2 8E0468P 8E0469W(9) (9) (9) (2) (4) (4) (9) (9) (9) (9)

8E9543HX 6Y8558P 8E5559W 1U0740HX 1U0739P 8E5559W 9N4552HX 9W1553RP2 6Y8558P 8E5559W(8) (8) (8) (2) (4) (4) (8) (8) (8) (8)



6I6608P 6I6609W 1U0740HX 1U0739P 8E5559W 7Y0602HX 6I6602RP2 6I6608P 6I6609W(9) (9) (2) (4) (4) (9) (9) (9) (9)

(See Page 35)

(See Page 34)

TEETH (See Pages 53 & 57) FASTENERS (See page 62 - 63)(See Page 62 - 63) FASTENERS (See Page 35)

VERTICAL PROTECTORTEETH/FASTENERSADAPTER COVER

FASTENERSHD

ADAPTERCOVER

34

ADAPTERCOVER LBS. KGS.

PART NO. A B C D E F G PIN WASHER

8J6398HX 6-1/8 (156) 1 (25) 2-5/16 (59) 4-1/8 (105) 7-1/8 (181) 5-3/4 (146) 1-3/16 (30) 22.4 10.2 6Y2527P 6Y9459W

1U0741HX 8-3/8 (213) 1-11/16 (43) 4-3/4 (121) 4-11/16 (119) 8-3/8 (213) 8-1/2 (216) 1-3/16 (30) 41.7 18.9 6Y8558P 8E5559W

9U9331HX 6-1/8 (156) 1 (25) 2-1/4 (57) 3-15/16 (100) 7-3/16 (183) 7 (178) 1-9/16 (40) 25.9 11.7 6Y2527P 6Y9459W

8E9543HX 7-1/4 (184) 1-11/16 (43) 4-5/8 (117) 4-13/16 (122) 8-3/8 (213) 8-11/16 (221) 1-11/16 (43) 46.1 20.9 6Y8558P 8E5559W

A

B

CDE

F

G

MODULOK DETAILS - Inches (mm)ADAPTER COVERS

DIMENSIONS - Inches (mm) FASTENERS(See Page 62 - 63)

WEIGHT

133-0734HX (Center)wt.= 77.0 lbs. 34.9 kgs.

Uses 6I6608P pin and 6I6609W washer(see page 63 for pin and washer details)

133-0735HX (Corner)wt.= 73.0 lbs. 33.1 kgs.

Uses 6I6608P pin and 6I6609W washer(see page 63 for pin and washer details)

35

MODULOK DETAILS cont'd. - Inches (mm)

EC

DA

PROTECTORPART NO. A B C D E LBS. KGS. PIN WASHER*

8J6399HX 20-1/2 (521) 3-3/8 (86) 1-3/8 (35) 10 (254) 5-1/2 (140) 33.4 15.2 9J8442P 6Y9459W

9J9600HX 22-3/4 (578) 3-1/2 (89) 1-3/8 (35) 10 (254) 5-13/16 (148) 38.0 17.2 9J8442P 6Y9459W

1U0740HX 23-1/2 (597) 3-1/2 (89) 2-1/8 (54) 11-1/2 (292) 5-1/4 (133) 49.0 22.2 1U0739P 8E5559W

VERTICAL PROTECTORS

BDIMENSIONS - Inches (mm) FASTENERS

TYPE 2CORNER

AB

C

ED

BA

C

TYPE 1CENTER

ADAPTERPART NO. TYPE A B C D E LBS. KGS.

8J6396HX 1 13-3/16 (335) 5-15/16 (176) 2-1/8 (54) 3-5/16 (84) 50.5 22.9

8J6397HX 2 13-3/16 (335) 6-15/16 (176) 2-1/8 (54) 3-5/16 (84) 5 (127) 53.7 24.3

*8E1464HXC 1 13-3/16 (335) 6-15/16 176) 2-1/8 (54) 3-5/16 (84) 51.0 23.1

*8E1465HX 2 13-3/16 (335) 6-15/16 (176) 2-1/8 (54) 3-5/16 (84) 5 (127) 52.7 23.9

1U1554HX 1 17 (432) 8 (203) 2-5/8 (67) 4-3/4 (121) 112.0 50.8

119-9605HX 1 15-7/8 (403) 9-13/16 (249) 2-13/16 (71) 5-3/16 (132) 141.0 63.9

119-9604HX 1 18-7/8 (479) 9-13/16 (249) 2-13/16 (71) 5-3/16 (132) 144.0 65.3


* Larger pin hole diameter for oversize fasteners.

FLUSH MOUNT ADAPTERS

WEIGHT

WEIGHT

Requires a 6Y9459W steel washer.

9J8442Pwt.= 0.8 lbs. 0.4 kgs.

Requires an 8E5559W steel washer

1U0739Pwt.= 1.0 lbs. 0.4 kgs.

VERTICAL PROTECTOR PINS

*see page 63 for washer details

D

36

SEGMENTPART NO. TYPE A B C D E F LBS. KGS.

9J4429HX 1 9 (229) 11-1/2 (292) 3-11/16 (94) 2-9/16 (65) 3-3/8 (86) 11/16 (17) 29.6 13.48J8313HX 1 13-3/8 (340) 16-1/8 (410) 3-11/16 (94) 2-9/16 (65) 3-3/16 (81) 11/16 (17) 41.2 18.7

8J8222HX(RH)& 2 10-3/16 (259) 13(330) 3-1/2 (89) 2-3/4 (70) 3-1/4 (83) 11/16 (17) 35.0 ea. 15.9 ea.

8J8223HX (LH)9U9332CHX 1 9 (229) 11-1/2 (292) 4-7/8 (124) 3-1/16 (78) 3 (76) 1-1/2 (38) 39.0 17.79U9333LHX

& 2 10-1/2 (267) 13 (330) 4 (102) 3-1/4 (83) 3-1/8 (79) 1-1/2 (38) 40.7 ea. 18.4 ea.9U9334RHX9U9664CHX 1 11-1/2 (292) 14 (356) 4-11/16 (119) 3-1/16 (78) 2-11/16 (68) 1-1/2 (38) 46.5 21.11U0869HX 1 15-7/8 (403) 18-1/2 (470) 3-7/16 (87) 3-13/16 (97) 3-9/16 (90) 3/4 (19) 63.3 28.7

102-9681LHX& 2 16 (406) 18-5/8 (473) 6 (152) 3 (76) 3-1/8 (79) 1-1/4 (32) 72.0 32.7

102-9680RHX8J3962HX 1 13-1/8 (333) 15-1/2 (394) 4-13/16 (122) 3-1/16 (78) 3 (76) 1-1/2 (38) 57.3 25.9

9J9973HX(RH)& 2 14-5/16 (364) 17- 1/16 (433) 4-9/16 (116) 2-5/16 (135) 3-1/8 (79) 7/8 (22) 53.2 ea. 24.1 ea.

9J9974HX (LH)8E9514HX 1 15-3/4 (400) 18-3/8 (467) 5-1/2 (140) 2-9/16 (65) 3-3/8 (86) 1-3/4 (44) 83.0 37.6

8E9516HXL& 2 14-1/4 (362) 17-1/16 (433) 5 (127) 2-5/8 (67) 3-1/8 (79) 1-3/4 (44) 69.0 ea. 31.3 ea.

8E9515HXR

EDGE SEGMENTS

B

C D

E

F

A B

C D

E

F

TYPE 1(CENTER)

TYPE 2(LH Shown,

RH Opposite)

A


MODULOK DETAILS cont'd. - Inches (mm)

37

BOTTOM VIEW of LOADER BUCKET

Center Segment

Right-HandSegment

Left-HandSegment

Bolt-On Heel Plate

• Durable heat-treated steel castings thru-hardened to 500 Brinnell

• Half arrow design increases penetration and protects the leading edge

• Ribbed-bottom design traps material to reduce wear

• Thicker material on the bottom extends wear life

Heavy duty bolt-onsegment with ribbedbottom

(See pages 42 - 46 for all bolt-on segmentand heel plate details)

BOLT-ON SEGMENTS & HEEL PLATES forLOADERS

38

BOLT-ON REVERSIBLE SEGMENT DETAILS - Inches (mm)

TYPE 1(Center)

TYPE 2(LH Shown, RH Opposite)

BOLT-ON HALF ARROW SEGMENT DETAILS - Inches (mm)

4T6700HXwt.= 52.8 lbs. 23.9 kgs.

Requires (2) 1-1/4 X 4 Plow Bolts*Plow Bolt Assembly No. A114-400

D

A

BC

E F

A

D

C

B

E F

SEGMENTPART NO. TYPE A B C D E F LBS. KGS. SIZE *ASSY. NO. QTY.

100-6666NRHX 1 12-1/4 (311) 11-9/16 (294) 8 (203) 3-7/8 (98) 2-1/2 (64) 1-5/8 (41) 44.0 19.9 1-1/4 X 4-1/2 A114-412 2

109-9019NRHX 1 13-1/8 (333) 12-1/2 (318) 7-1/4 (184) 4-1/16 (103) 2-5/8 (67) 1-5/8 (41) 58.0 26.3 1-1/4 X 4-1/2 A114-412 2

132-1037NRHX 1 9-15/16 (252) 10-3/8 (263) 7-11/16 (195) 3-5/32 (80) 2 (25) 1-1/8 (29) 25.0 11.3 1 X 3 A10-300 2

135-9544HX‡ 1 15-3/4 (400) 11-13/16 (300) 4-3/4 (121) 5 (127) 2-13/16 (71) 1-3/4 (44) 76.6 34.7 1-1/4 X 3-1/4 N/A 2

135-9545HX‡& 2 15-3/4 (400) 12 (305) 7-5/8 (194) 5 (127) 2-13/16 (71) 1-3/4 (44) 78.6 35.7 1-1/4 X 3-1/4 N/A 2

135-9546HX‡

4T3015NRHX 1 12-9/16 (319) 10-1/8 (257) 5-5/16 (135) 4-3/4 (121) 2-1/2 (64) 1-5/8 (41) 40.0 18.1 1-1/4 X 4 A114-400 2

4T6692NRHX 1 10-1/4 (261) 7-3/4 (197) 4-15/16 (125) 3-3/16 (81) 2-1/8 (54) 1-1/2 (38) 23.5 10.7 1 X 3 A10-300 2

4T6693NRHX 1 10-1/4 (261) 8-1/2 (216) 5-17/32 (140) 3-3/16 (81) 2-1/8 (54) 1-1/2 (38) 26.0 11.8 1X3 A10-300 2

4T6694NRHX 1 10-1/4 (261) 9 (229) 6-1/8 (156) 3-3/16 (81) 2-1/8 (54) 1-1/2 (38) 27.1 12.3 1X3 A10-300 2

4T6696NRHX 1 12-9/16 (319) 7-9/16 (192) 3-9/16 (90) 3-15/16 (100) 2-1/2 (63) 1-5/8 (41) 30.3 13.8 1-1/4X3 A114-300 2

4T6697NRHX 1 12-9/16 (319) 8-3/8 (213) 4-3/4 (121) 4-3/4 (121) 2-1/2 (64) 1-5/8 (41) 33.9 15.4 1-1/4 X 4 A114-400 2

4T6698NRHX 1 12-1/4 (311) 9-1/2 (241) 5-1/2 (140) 3-7/8 (98) 2-1/2 (64) 1-5/8 (41) 35.5 16.1 1-1/4 X 4 A114-400 2

4T6699NRHX 1 12-1/4 (311) 10-5/8 (270) 7-1/16 (179) 3-7/8 (98) 2-1/2 (64) 1-5/8 (41) 42.5 19.3 1-1/4 X 4 A114-400 2

4T6700NRHX 1 12-5/16 (313) 11-3/8 (289) 6-5/16 (289) 3-7/8 (98) 2-1/2 (64) 1-5/8 (41) 46.0 20.9 1-1/4 X 4 A114-400 2

4T7139NRHX& 2 12-9/16 (319) 12 (305) 5-5/16 (135) 4-3/4 (121) 2-1/2 (64) 1-5/8 (41) 46.1 ea. 20.9 ea. 1-1/4 X 4 A114-400 2

4T7140NRHX

4T9123NRHX& 2 12-9/16 (319) 10-9/16 (268) 5-3/4 (146) 4-3/4 (121) 2-1/2 (64) 1-5/8 (41) 45.2 ea. 20.5 1-1/4 X 4 A114-400 2

4T9124NRHX

DIMENSIONS - Inches (mm) PLOW BOLTSWEIGHT

*see page 78 for assembly details‡ these segments have rounded noses rather than pointed as shown in the illustrations.

39

BOLT-ON HALF ARROW SEGMENT DETAILS cont'd. - Inches (mm)

TYPE 1(Center)

TYPE 2(LH shown, RH Opposite)

SEGMENTPART NO. TYPE A B C D E F LBS. KGS. SIZE *ASSY. NO. QTY.

1099080NRHX 1 15-5/8 (397) 13-1/2 (343) 3-3/8 (86) 5-3/8 (136) 2-3/4 (70) 1-3/4 (44) 83.0 37.6 1-1/4 X 4 A114-400 3

1099081NRHX& 2 15-5/8 (397) 13-1/2 (343) 3-3/8 (86) 5-3/8 (136) 2-3/4 (70) 1-3/4 (44) 86.0 39.0 1-1/4 X 4 A114-400 3

1099082NRHX

9W5734NRHX 1 15-5/8 (397) 12-1/4 (311) 3-3/8 (86) 5-3/8 (137) 2-3/4 (70) 1-3/4 (44) 64.0 29.0 1-1/4 X 4 A114-400 3

9W5730NRHX& 2 15-5/8 (397) 12-11/16 (322) 3-3/8 (86) 5-3/8 (137) 2-3/4 (70) 1-3/4 (44) 68.0 30.8 1-1/4 X 4 A114-400 3

9W5737NRHX


A

B

C

D

E F

C



A

B

C

D

E F

C

116-7460CHX (Center)wt.= 75.5 lbs. 34.2 kgs.


116-7462LHX (LH Shown)116-7461RHX (RH Opposite)wt.= 75.5 lbs. 34.2 kgs. each

Requires (3) 1-1/4 X 4 Plow Bolts*Plow Bolt Assembly Part No. A114-400

40

BOLT-ON SEGMENT DETAILS cont'd. - Inches (mm)

4T6760NRHHX (Center)wt.= 179.0 lbs. 81.2 kgs.


4T6762NRHHX (LH Shown) 4T6761NRHHX (RH Opposite)wt.= 195.0 lbs. 88.5 kgs. each


4T6760NRHX (Center)wt.= 168.0 lbs. 76.2 kgs.


4T6762NRHX (LH Shown) 4T6761NRHX (RH Opposite)wt.= 175.0 lbs. 79.3 kgs. each



109-2675NRHX (Center)wt.= 246.0 lbs. 111.6 kgs.

Requires (4) 1-1/4 X 4-1/2 Plow Bolts*Plow Bolt Assembly No. A114-412

109-2677NRHX (LH Shown) 109-2676NRHX (RH Opposite)wt.= 268.0 lbs. 121.7 kgs. each

Requires (4) 1-1/4 X 4-1/2 Plow Bolts*Plow Bolt Assembly Part No. A114-412

41

TOP COVER PLATES - Inches (mm)

195-7097HX (RH Shown) 195-7098HX (LH Opposite)wt.= 56.5 lbs. 25.7 kgs. each

Used with the following segments:4T6761NRHX & 4T6762NRHX

4T6761NRH-HX & 4T6762NRH-HX109-2676NRHX & 1092677NRHX

195-7096HX (Center)wt.= 50.0 lbs. 22.70 kgs.

Used with the following segments:4T6760NRHX

4T6760NRH-HX109-2675NRHX

42

1-1/2 (38)

5-1/8(130)

23(584)

19-7/16(494)

10 (254)

1-5/8 (41)

3-15/16 (100)

23-7/8(606) 6-1/4

(159)

20-5/8(254)

9W6749HXwt.= 76.0 lbs. 34.5 kgs.

Requires (4) 3/4 X 2-1/2 Plow Bolts*Plow Bolt Assembly No. A34-212

7V0910HXwt.= 101.0 lbs. 45.8 kgs.


1-1/2 (38)

5 (127)

10 (254)

27-9/16(700) 24

(610)

6Y3610HXwt.= 245.0 lbs. 111.1 kgs.

Requires (4) 1 X 3-1/2 Plow Bolts*Plow Bolt Assembly No. A10-312

6Y3609HXwt.= 94.0 lbs. 42.6 kgs.


5 (127)

1-13/16 (46)

14 (356)

40-1/2(1029)

6-1/16(154)

36(914)

12-1/2 (318)

BOLT-ON HEEL PLATE DETAILS - Inches (mm)


43

BOLT-ON HEEL PLATE DETAILS cont'd. - Inches (mm)

109-9215HXwt.= 84.0 lbs. 38.1 kgs.


6Y3573HXwt.= 160.0 lbs. 72.6 kgs.


9W6748HXwt.= 44.7 lbs. 20.3 kgs.



9W6747HXwt.= 46.5 lbs. 21.1 kgs.


44

THIS PAGE INTENTIONALLYLEFT BLANK

45

BOTTOM VIEW of LOADER BUCKET

BOLT-ON HALF ARROW EDGE SYSTEMS FORLOADERS

• Durable heat-treated steel castings thru-hardened to 500 Brinnell

• Half arrow design increases penetration and protects the leading edge

• Ribbed-bottom design traps material to reduce wear

• Thicker material on the bottom extends wear life

Heavy duty bolt-onsegments with ribbedbottom

(See pages 48 - 49 for all bolt-on half arrowedge systems details)

Half arrowcenter edge

Half arrowend edge

Bolt-onheel plate

Half arrowcenter edge

Half arrowend edge

46

CENTER SEGMENTS

END SEGMENTS

BOLT-ON HEEL HALF ARROW EDGES - Inches (mm)

TYPICAL DRAWING

BUCKETWIDTH

inches (MM)

988F, G 145-7/32 (3,688) 104-5841NR3HX A114-412(4) 3

980F, G 134 (3,406) 109-9212NRHX A114-412 (4) 3

980F, G 134 (3,406) 109-9212NRLT A114-412 (2) 3

980C, D, E, F 130-3/4 (3,322) 1U0762NRHX A114-412 (4) 3

980C, D, E, F 130-3/4 (3,322) 1U0762NRLT A114-412 (2) 3

970, 970F 126 (3,200) 100-6668NRHX A114-412 (4) 3

970, 970F 119-1/2 (3,035) 1U0593NRHX A114-412 (4) 3

966D, E, F 119-1/2 (3,035) 1U0593NRHX A114-412 (4) 3

962G 115 (2,921) 135-9666NRHX A10-314 (2) 3

950G 115 (2,921) 135-9666NRHX A10-314 (2) 3

950B, E, F 108 (2,743) 132-1034NRHX A10-314 (2) 3

PARTNUMBER

PLOW BOLTASSEMBLY*

(no. req'd.)

LOADERMODEL

NUMBER OFSEGMENTSREQUIRED

BUCKETWIDTH

inches (MM)

988F, G 145-7/32 (3,688) 1U0761NR2HX A114-412(3) 2

980F, G 134 (3,406) 1U0761NRHX A114-412 (3) 2

980C, D, E, F 130-3/4 (3,322) 1U0761NRHX A114-412 (3) 2

970, 970F 126 (3,200) 3G6395RNRHX A114-412 (3) 13G6395LNRHX " 1

970, 970F 119-1/2 (3,035) 3G6395RNRHX A114-412 (3) 13G6395LNRHX " 1

966D, E, F 119-1/2 (3,035) 3G6395RNRHX A114-412 (3) 13G6395LNRHX " 1

962G 115 (2,921) 132-1033NRHX A10-314 (3) 2

950G 115 (2,921) 132-1033NRHX A10-314 (3) 2

950B, E, F 108 (2,743) 132-1033NRHX A10-314 (3) 2

PARTNUMBER

NUMBER OFSEGMENTSREQUIRED

LOADERMODEL

PLOW BOLTASSEMBLY*

(no. req'd.)


47

CENTER SEGMENTS

END SEGMENTS

1U0761NRHX76.0 lbs. 345.5 kgs.FITS BOTH SIDES

TYPE 1 TYPE 2

BOLT-ON HEEL HALF ARROW EDGES DETAILS - Inches (mm)

PARTNUMBER A B C D

WEIGHT

LBS.E F HG KGS.

104-5841NR3HX 1 40-7/8 (1038) 16-3/4 (425) 3-1/16 (78) 1-13/16 (46) 4-1/16 (103) 6-1/8 (156) 20-9/16 (522) 1-3/8 (35) 270.0 122.6

109-9212NRHX 1 37-15/16 (964) 16-3/4 (425) 3 (76) 1-3/4 (44) 4-1/16 (103) 6-5/32 (156) 19-1/8 (485) 1-3/8 (35) 265.0 120.0

109-9212NRLT 2 37-15/16 (964) 12-11/16 (322) 3-1/16 (78) 1-13/16 (46) 4-1/16 (103) N/A 19-3/32 1-3/8 (35) 200.0 90.8

1U0762NRHX 1 36-3/4 (933) 16-3/4 (425) 3 (76) 1-3/4 (44) 4-1/16 (103) 6-5/32 (156) 18-1/2 (470) 1-3/8 (35) 256.0 116.0

1U0762NRLT 2 36-3/4 (933) 12-11/16 (322) 3-1/4 (83) 1-13/16 (46) 4-1/16 (103) N/A 18-1/2 (470) 1-3/8 (35) 215.0 97.5

100-6668NRHX 1 35-3/8 (899) 15-5/8 (397) 2-3/4 (69) 1-5/8 (41) 3-15/16 (100) 5-15/16 (151) 17-13/16 (452) 1-3/8 (35) 200.0 90.7

1U0593NRHX 1 33-1/2 (851) 15-5/8 (397) 2-3/4 (69) 1-5/8 (41) 3-15/16 (100) 5-15/16 (151) 17-13/16 (452) 1-3/8 (35) 180.0 81.6

135-9666NRHX 2 32-13/32 (823) 9-3/4 (248) 2-1/4 (57) 1-1/2 (38) 3-3/16 (81) N/A 16-5/16 (415) 1-1/16 (27) 119.0 54.0

132-1034NRHX 2 30-1/4 (768) 9-3/4 (248) 2-1/4 (57) 1-1/2 (38) 3-3/16 (81) N/A 15-1/4 (387) 1-1/16 (27) 110.0 49.9

TYPEDIMENSIONS - Inches (mm)

1U0761NR2HX86.0 lbs. 39.0 kgs.FITS BOTH SIDES

3G6395RNRHX (R. HAND SHOWN)3G6395LNRHX (L. HAND OPPOSITE)

62.0 lbs. 28.1 kgs.RIGHT AND LEFT HAND REQUIRED

132-1033NRHX46.5 lbs. 21.1 kgsFITS BOTH SIDES

48

REPLACEMENT TEETH for

J200 9W7112P 4T0001W 7T8202HX 1U3202HX -- T1U3202 1U3202WT 4T2203HX --1U3201HX

J225 6Y3228P 3G9609W -- 6Y3222HX 8E4222HX T6Y3222 6Y3222WT -- --(101-0706)

J250 9J2258P 3G9609W† 1U3251HX 1U3252HX 9N4252HX T1U3252 1U3252WT 4T2253HX 1U3252AP(101-0707)

J300 9J2308P 3G9609W† 1U3301HX 1U3302HX 9N4302HX T1U3302 1U3302WT 4T2303HX 1U3302APT1U3302L 1U3302WTL

(101-0708)

J350 9J2358P 6Y9459W† 1U3351HX 1U3352HX 9N4352HX T1U3352 1U3352WT 4T2353HX 1U3352APT1U3352L 1U3352WTL

(101-0709)

J400 7T3408P 7T3409W† 7T3401HX* 7T3402HX 8E4402HX T7T3402 7T3402WT 7T3403HX --

J450 6Y2527P 6Y9459W† 1U3451HX 9W8452HX 9N4452HX T1U3452 1U3452WT 9W1453HX 1U3452APJ460 8E0468P 8E0469W† T1U3452L 1U3452WTL 9W1453HHX

(101-0711) 9N4453HX

J550 6Y8558P 8E5559W 1U3551HX 9W8552HX 9N4552HX T1U3552 1U3552WT 9W1553HX 1U3552APT1U3552L 1U3552WTL 6Y2553HX

(101-0712) 9J4553HX9J4553HHX

J600 6I6608P 6I6609W -- 6I6602HX 7Y0602HX T6I6602 6I6602WT 6I6603HX --

J700 4T4708P 4T4707W 4T4702HX 9U9702HX* 4T4703HX9U9703HX*

TOOTH SERIES REFERENCE CHARTS (See pages 52 - 61 for tooth details)

*Future development †Harder Rockwell washers are also available.

CATTOOTHSERIES

TYPE 4TIGER

TYPE 1SHORT

TYPE 2LONG

TYPE 3HEAVYLONG

TYPE 5TWIN

TIGER

TYPE 6ABRASION

TYPE 7APALL

PURPOSE

TOOTH FASTENERS(See pages 61 - 62)

PIN WASHER

TYPE 1

SHORT(Details Page 50)

LONG(Details Page 50)

TYPE 2

HEAVY LONG(Details Page 51)

TYPE 3

TYPE 8

AGB(Details Page 54)

PENETRATOR(Details Page 54)

TYPE 9 TYPE 10(RP-2 & RP-3)

ROCK PENETRATOR

(Details Page 55)

A(DEPTH)

BHEIGHT

D(TOP WIDTH)

(CENTER WIDTH)C

D(BOTTOM WIDTH)

TOOTH POCKET CROSS REFERENCE

A B C D

J200 2-7/16 (62) 1-27/32 (47) 1-9/16 (40) 1-13/32 (36)J225 2-13/16 (71) 2-11/32 (60) 1-15/16 (49) 1-3/4 (44)J250 3-1/8 (79) 2-11/16 (68) 2-5/32 (55) 1-15/16 (49)J300 3-1/2 (89) 3-1/32 (77) 2-5/8 (67) 2-3/8 (60)J350 4 (102) 3-5/16 (84) 2-15/16 (75) 2-11/16 (68)J400 4-7/16 (113) 3-21/32 (93) 3-15/32 (88) 3-5/32 (80)

J450 / J460 4-3/4 (121) 3-29/32 (99) 3-7/8 (98) 3-17/32 (90)J550 5-19/32 (142) 4-11/32 (110) 4-11/16 (119) 4-5/16 (110)J600 6-11/16 (170) 5-7/32 (133) 5-5/8 (143) 5-5/32 (131)J700 6-15/16 (176) 5-11/16 (144) 6 (152) 5-1/2 (140)

DIMENSIONS - Inches (mm)CATTOOTHSERIES

49

EXCAVATORS, LOADERS & SCRAPERS

-- -- -- -- -- 1U3202FHX -- 9W7112P 4T0001W J200

-- 6Y8229HX -- -- -- -- 6Y3222F 6Y3228P 3G9609W J225

-- 9J4259HX 4T2253RP2 1U3252RC -- 3G8250HX -- 9J2258P 3G9609W† J250

4T2303AGBHX 9J4309THX 4T2303RP2 1U3302RC 1U3302SYL 4T1300HX 1U3302FHX 9J2308P 3G9609W† J300(107-3300)

4T2353AGBHX 9J4359THX 4T2353RP2 1U3352RC 1U3352SYL 8J3350FHX 1U3352FHX 9J2358P 6Y9459W† J350(107-3350)

7T3403AGBHX 6Y7409HX 7T3403RP2 7T3402RC 8E4402SYL -- 7T3402F 7T3408P 7T3409W† J400(107-3400)

9W1453AGBHX 9J4459THX 9W1453RP2 1U3452RC 9W8452SYL 8J1450FHX 1U3452FHX 6Y2527P 6Y9459W† J4509W1453RP3 (107-3450) 8E0468P 8E0469W† J460

9W1553AGBHX 9W8559HX 9W1553RP2 1U3552RC 9W8552SYL 7J9550FHX 1U3552FHX 6Y8558P 8E5559W J550or (107-3550)

9W1553RP3

-- 7I7609* 6I6602RP2 6I6602RC 6I6602SYL -- 6I6602F 6I6608P 6I6609W J6006I6602RP3

4T4709HX 4T4703RP2 4T4702RC 4T4702SYL 4T4708P 4T4707W J7004T4703RP3

TYPE 10ROCK

PENETRATORRP2 & RP3

TYPE 11ROCK

CHISELTYPE 12

SYL

TYPE 13FLARE

OLD STYLE

TYPE 14FLARE

STANDARD

TYPE 8AGB

(ABRASION)TYPE 9

PENETRATOR

TOOTH FASTENERS(See pages 61 - 62)

PIN WASHER

TYPE 4

TIGER(Details Page 52)

TWIN TIGER(Details Page 52)

TYPE 5 TYPE 6

ABRASION(Details Page 53)

TYPE 7

ALL PURPOSE(Details Page 53)

TYPE 12

SYL(Details Page 56)

TYPE 11

ROCK CHISEL (RC)(Details Page 56)

CATTOOTHSERIES

TYPE 13

OLD STYLE FLARE(Details Page 57)

TYPE 14

STANDARD FLARE(Details Page 57)

50

TOOTH DETAILS - Inches (mm)

CAT TOOTHSERIES PART NO. DESCRIPTION A B C D LBS. KGS.

J200 7T8202HX Utility 4-11/16 (119) 1-15/16 (49) 2-3/8 (60) 2-1/8 (54) 1.8 0.8

J200 1U3201HX Short 5-1/4 (133) 2-1/4 (57) 2-7/16 (61) 2-1/4 (57) 3.1 1.4

J250 1U3251HX Short 6-9/16 (167) 2-9/16 (65) 3-3/8 (86) 2-7/8 (73) 6.0 2.7

J300 1U3301HX Short 7-1/2 (191) 3 (76) 4 (102) 3-5/16 (84) 8.2 3.7

J350 1U3351HX Short 8-1/8 (206) 3-1/2 (89) 4-3/8 (111) 4 (102) 13.4 6.1

J450 1U3451HX Short 9-7/8 (251) 4-5/8 (117) 4-13/16 (122) 5 (127) 22.8 10.3

J550 1U3551HX Short 11-1/4 (286) 5-3/4 (146) 5-3/4 (146) 6-1/16 (154) 30.2 13.7

STANDARD TOOTH DIMENSIONS - Inches (mm) WEIGHT

TYPE 1SHORT

TYPE 2LONG


J200 1U3202HX Long 5-3/4 (146) 2 (51) 2-3/8 (60) 2-1/4 (57) 2.8 1.3

J225 6Y3222HX Long 6-5/8 (168) 2-1/4 (57) 3-3/16 (81) 2-19/32 (66) 4.6 2.1

J250 1U3252HX Long 7-1/2 (191) 2-9/16 (65) 3-1/4 (82) 2-7/8 (73) 6.4 2.9

J300 1U3302HX Long 8-9/16 (217) 3 (76) 4 (102) 3-5/16 (84) 9.8 4.4

J350 1U3352HX Long 9-1/2 (241) 3-5/8 (92) 4-3/8 (111) 4 (102) 13.5 6.1

J400 7T3402HX Long 10-1/2 (267) 4-1/4 (108) 5 (127) 4-11/16 (119) 22.9 10.4

J450 9W8452HX Long 11-3/8 (289) 4-1/2 (114) 4-13/16 (122) 5 (127) 25.5 11.6

J550 9W8552HX Long 13-3/16 (335) 5-5/8 (143) 5-3/4 (146) 6-1/16 (154) 37.9 17.2

J600 6I6602HX Long 15 (381) 6-1/2 (165) 7-1/4 (184) 7-3/4 (197) 72.0 32.7

J700 4T4702HX Long 16-1/2 (419) 7-1/8 (181) 8-3/8 (213) 7-7/8 (200) 95.0 43.1


51

TOOTH DETAILS cont'd. - Inches (mm)


J225 8E4222HX Heavy 7 (178) 2-3/16 (56) 3-3/16 (81) 2-19/32 (66) 5.6 2.5

J250 9N4252HX Heavy 7-7/8 (200) 2-7/16 (61) 3-1/2 (89) 3 (76) 8.4 3.8

J300 9N4302HX Heavy 8-3/4 (222) 2-3/4 (70) 4-3/16 (106) 3-7/16 (87) 12.2 5.5

J350 9N4352HX Heavy 9-7/8 (251) 3-1/2 (89) 4-7/16 (113) 4 (102) 18.0 8.2

J400 8E4402HX Heavy 11 (279) 4 (102) 5 (127) 4-11/16 (119) 24.8 11.3

J450 9N4452HX Heavy 12-1/2 (317) 4-1/2 (114) 5-3/8 (137) 5-3/16 (132 ) 37.6 17.1

J550 9N4552HX Heavy 13-3/4 (349) 5-3/4 (146) 6-1/8 (156) 6-1/4 (159) 61.0 27.7

J600 7Y0602HX Heavy 16 (406) 6-1/2 (165) 7-1/2 (191) 7-1/2 (191) 91.0 41.3


TYPE 3HEAVY LONG

52

TYPE 4TIGER

TYPE 5TWIN TIGER


J200 T1U3202 Standard 6-1/2 (165) 2-3/8 (60) 2-1/4 (57) 2.4 1.1

J225 T6Y3222 Standard 7-7/8 (200) 3-3/16 (81) 2-19/32 (66) 4.7 2.1

J250 T1U3252 Short 8 (203) 3-5/16 (84) 2-7/8 (73) 6.2 2.8

J300 T1U3302 Short 9 (229) 3-3/4 (95) 3-1/4 (83) 9.2 4.1

J300 T1U3302L Standard 9-1/2 (241) 3-3/4 (95) 3-1/4 (83) 9.3 4.2

J350 T1U3352 Short 11 (279) 4-7/16 (113) 3-15/16 (100) 13.0 5.9

J350 T1U3352L Standard 11-1/4 (286) 4-5/16 (110) 4 (102) 13.2 6.0

J400 T7T3402 Standard 12-1/2 (318) 5-3/32 (129) 4-11/16 (119) 21.2 9.6

J450 T1U3452 Short 12 (305) 4-3/4 (121) 4-7/8 (124) 18.7 8.5

J450 T1U3452L Standard 14-1/16 (357) 5-3/8 (137) 5-1/4 (133) 28.7 13.0

J550 T1U3552 Short 13-1/4 (337) 5-3/4 (146) 6 (152) 28.5 12.9

J550 T1U3552L Standard 15 (381) 5-3/4 (146) 6-1/8 (156) 35.9 16.3

J600 T6I6602 Standard 18 (457) 7-1/4 (184) 7-3/4 (197) 68.0 30.8

TIGER TOOTH DIMENSIONS - Inches (mm)

A

C

D

C

A

DB

WEIGHT


J200 1U3202WT Standard 6-1/2 (165) 3 (76) 2-3/8 (60) 2-1/4 (57) 3.0 1.4

J225 6Y3222WT Standard 7-7/8 (200) 3-3/8 (86) 3-1/16 (78) 2-19/32 (66) 5.8 2.6

J250 1U3252WT Short 8 (203) 3-1/2 (89) 3-5/16 (84) 2-7/8 (73) 7.5 3.4

J300 1U3302WT Short 9 (229) 3-13/16 (97) 4 (102) 3-1/4 (83) 11.2 5.1

J300 1U3302WTL Standard 9-1/2 (241) 4-5/32 (106) 4-3/16 (106) 4-7/16 (113) 10.7 4.8

J350 1U3352WT Short 10-1/2 (267) 4-3/4 (121) 4-3/8 (111) 4 (102) 16.1 7.3

J350 1U3352WTL Standard 11-1/4 (286) 4-3/4 (121) 4-5/16 (110) 4 (102) 14.2 6.4

J400 7T3402WT Standard 12-1/2 (318) 5-9/16 (141) 5-3/32 (129) 4-11/16 (119) 23.8 10.8

J450 1U3452WT Short 12 (305) 5-3/4 (146) 4-3/4 (121) 5 (127) 24.5 11.1

J450 1U3452WTL Standard 14-1/16 (357) 6-7/32 (158) 5-3/8 (137) 5-1/4 (133) 31.7 14.4

J550 1U3552WT Short 13 (330) 6-3/4 (171) 5-3/8 (137) 6 (152) 32.7 14.8

J550 1U3552WTL Standard 15 (381) 7-1/4 (184) 5-3/4 (146) 6-1/8 (156) 40.1 18.2

J600 6I6602WT Standard 18 (457) 9-1/4 (235) 7-1/4 (184) 7-3/4 (197) 76.0 34.5

TWIN TIGER TOOTH DIMENSIONS - Inches (mm) WEIGHT


53

TYPE 6ABRASION

TYPE 7ALL PURPOSE

CAT TOOTH ABRASION TOOTHSERIES PART NO. A B C D LBS. KGS.

J200 4T2203HX 5-3/4 (146) 2-3/8 (60) 2-9/16 (65) 2-1/4 (57) 3.5 1.6

J250 4T2253HX 7-9/16 (192) 3-1/8 (79) 3-9/32 (83) 2-15/16 (75) 7.3 3.3

J300 4T2303HX 8-5/8 (219) 3-7/8 (98) 4-1/8 (105) 3-1/2 (89) 12.0 5.4

J350 4T2353HX 9-1/2 (241) 4-1/4 (108) 4-7/16 (113) 4 (102) 16.7 7.6

J400 7T3403HX 10-3/4 (273) 5-11/16 (144) 5 (127) 4-3/4 (121) 33.0 14.9

J450 9W1453HX 11-5/8 (295) 5-5/8 (143) 5-5/16 (135) 5 (127) 31.7 14.4

J450 9W1453HHX 11-5/8 (295) 5-5/8 (143) 5-5/16 (135) 5 (127) 36.0 16.3

J450 9N4453HX 12-1/4 (311) 6-3/8 (162) 5-21/32 (144) 5-1/4 (133) 55.0 24.9

J550 9J4553HX 13 (330) 6-7/8 (175) 6-1/16 (154) 6-3/8 (162) 50.9 23.0

J550 9J4553HHX 13 (330) 6-3/4 (171) 6-1/16 (154) 6-3/8 (162) 59.0 26.8

J550 9W1553HX 13-1/8 (333) 7 (178) 5-13/16 (148) 6-1/4 (159) 51.5 23.4

J550 6Y2553HX 14 (356) 7-1/2 (191) 6-7/32 (158) 6-1/4 (159) 71.0 32.2

J600 6I6603HX 16-1/4 (413) 9 (229) 8-1/8 (206) 7-3/4 (197) 125.0 56.7

J700 4T4703HX 16-3/8 (416) 9-3/8 (238) 8 (203) 7-7/8 (200) 105.0 47.6

CAT TOOTH ALL PURPOSE TOOTHSERIES PART NO. A B C D LBS. KGS.

J250 1U3252AP 7-1/2 (191) 2-1/2 (64) 3-5/16 (84) 2-7/8 (73) 6.2 2.8

J300 1U3302AP 8-1/2 (216) 3 (76) 3-13/16 (97) 3-5/16 (84) 10.1 4.6

J350 1U3352AP 9-1/2 (241) 3-1/2 (89) 4-3/16 (106) 3-5/8 (92) 13.9 6.3

J450 1U3452AP 11-1/8 (283) 4-3/8 (111) 5 (127) 4-7/8 (124) 25.2 11.4

J550 1U3552AP 13-5/8 (346) 5-1/2 (140) 6-3/16 (81) 6-1/4 (159) 46.1 20.9



B

A

D

C

B D

C

WEIGHT

WEIGHT


A

54

B D

A

C

CAT TOOTHSERIES PART NO. A B C D LBS. KGS.

J225 6Y8229HX 6-9/16 (167) 1-1/4 (32) 3-3/16 (81) 2-5/8 (67) 4.2 1.9

J250 9J4259HX 7-9/16 (192) 1-5/16 (33) 3-1/2 (89) 3 (76) 6.3 2.9

J300 9J4309THX 8-1/2 (216) 1-1/2 (38) 3-13/16 (97) 3-9/16 (90) 7.8 3.5

J350 9J4359THX 9-7/8 (251) 2 (51) 4-1/4 (108) 3-7/8 (98) 12.3 5.6

J400 6Y7409HX 10-1/2 (267) 2 (51) 5-1/8 (130) 4-5/8 (117) 19.5 8.8

J450 9W8459HX 11-5/8 (295) 2 (51) 5-1/8 (130) 5 (127) 22.1 10.0

J550 9W8559HX 13-1/4 (337) 2-5/8 (67) 5-3/4 (146) 6 (152) 36.0 16.3

J700 4T4709HX 16-1/2 (419) 3-1/8 (79) 8-5/16 (211) 8-1/4 (209) 82.0 37.2

TYPE 9PENETRATOR


PENETRATOR TOOTHDIMENSIONS - Inches (mm)

TYPE 8AGB

WEIGHT

CAT TOOTH AGB (ABRASION) TOOTHSERIES PART NO. A B C D LBS. KGS.

J300 4T2303AGBHX 9 (229) 4 (102) 4-1/8 (105) 3-19/32 (91) 14.5 6.6

J350 4T2353AGBHX 10 (254) 4-3/4 (121) 4-19/32 (117) 4 (102) 18.7 8.5

J400 7T3403AGBHX 11-1/2 (292) 5-3/4 (146) 5-3/16 (132) 4-7/8 (124) 30.3 13.7

J450 9W1453AGBHX 12-1/4 (311) 6 (152) 5-1/2 (140) 5-3/16 (132) 35.3 16.0

J460

J550 9W1553AGBHX 14-1/4 (362) 7-1/4 (184) 6-1/2 (165) 6-5/16 (160) 62.0 28.1


55


TYPE 10ROCK PENETRATOR

CAT TOOTHSERIES A B C D LBS. KGS.

J250 4T2253RP2 9-1/2 (241) 2-5/8 (67) 3-23/32 (94) 2-15/16 (75) 11.9 5.4

J300 4T2303RP2 10-1/2 (267) 3-5/16 (84) 4-5/16 (110) 3-1/2 (89) 18.6 8.4

J350 4T2353RP2 11-11/16 (297) 3-3/4 (95) 4-25/32 (121) 4 (102) 26.0 11.8

J400 7T3403RP2 13 (330) 4-1/8 (105) 5-7/32 (133) 4-11/16 (119) 35.6 16.1

J450 9W1453RP2 13-13/16 (351) 4-27/32 (123) 5-9/16 (141) 5-1/4 (133) 47.8 21.7

J450 9W1453RP3 14-1/4 (362) 4-7/8 (124) 5-11/16 (144) 5-1/4 (133) 52.3 23.7

J550 9W1553RP2 14-3/4 (375) 5-5/32 (131) 6-1/32 (153) 6-1/4 (159) 58.0 26.3

J550 9W1553RP3 15-1/4 (387) 5-5/32 (131) 6-1/4 (159) 6-1/4 (159) 68.5 31.1

J600 6I6602RP2 17-3/4 (451) 6-1/4 (159) 7-5/16 (186) 7-3/4 (197) 109.0 49.4

J600 6I6602RP3 18-1/2 (470) 6-1/2 (165) 7-3/8 (187) 7-3/4 (197) 127.0 57.6

J700 4T4703RP2 19-1/2 (495) 6-7/8 (175) 8-1/16 (205) 7-3/4 (197) 113.5 51.5

J700 4T4703RP3 19-1/2 (495) 7 (178) 8-1/8 (206) 7-7/8 (198) 148.0 67.1

DIMENSIONS - Inches (mm)ROCK PENETRATOR

TOOTH PART NO.

WEIGHT

A

B D

C

56

B D

A

C


J250 1U3252RC 8-1/2 (216) 2-3/8 (60) 3-9/16 (90) 2-15/16 (75) 8.6 3.9

J300 1U3302RC 9-3/4 (248) 2-7/8 (210) 4-3/16 (106) 3-7/16 (87) 12.4 5.6

J350 1U3352RC 11 (279) 3-3/8 (86) 4-7/16 (113) 4 (102) 17.9 8.1

J400 7T3402RC 12-1/8 (308) 3-7/8 (98) 5-3/32 (129) 4-5/8 (117) 26.0 11.8

J450 1U3452RC 13 (330) 4-1/4 (108) 5-3/8 (137) 5-3/16 (132) 31.4 14.2

J550 1U3552RC 15 (381) 5-1/8 (130) 6-1/8 (156) 6-1/4 (159) 50.8 23.0

J600 6I6602RC 18 (457) 6-3/8 (162) 7-1/4 (184) 7-3/4 (197) 86.0 39.0

J700 4T4702RC 19 (483) 6-1/2 (165) 8-1/8 (206) 7-7/8 (200) 105.0 47.6


TYPE 11ROCK CHISEL

DIMENSIONS - Inches (mm)ROCK CHISEL TOOTH

WEIGHT

TYPE 12SYL


J300 1U3302SYLHX 9-1/4 (235) 3-7/16 (87) 4-3/16 (106) 3-7/16 (87) 10.9 4.9

J350 1U3352SYLHX 10-1/2 (267) 4 (102) 4-7/16 (113) 4 (102) 16.2 7.3

J400 8E4402SYLHX 11-3/4 (298) 4-11/16 (119) 5-3/32 (129) 4-11/16 (119) 24.4 11.1

J450 9W8452SYLHX 12-3/4 (324) 5-1/8 (130) 5-3/8 (136) 5-3/16 (132) 29.6 13.4

J460

J550 9W8552SYLHX 14-1/2 (368) 6 (152) 6-1/8 (156) 6-1/4 (159) 48.8 22.1

J600 6I6602SYLHX 16-1/2 (419) 7-1/2 (190) 7-1/4 (184) 7-3/4 (197) 76.0 34.5

J700 4T4702SYLHX 18 (457) 7-1/2 (190) 8-1/8 (206) 7-7/8 (200) 95.0 43.1

DIMENSIONS - Inches (mm)SYL TOOTH

WEIGHT

57



J200 1U3202FHX Old Style 5 (127) 4-3/8 (111) 2-5/16 (59) 2-3/8 (60) 2.8 1.3

J250 3G8250HX Old Style 7-3/4 (197) 4-1/2 (114) 3-9/16 (90) 2-7/8 (73) 9.2 4.2

J300 4T1300HX Old Style 8-1/2 (216) 6 (152) 3-7/8 (98) 3-3/8 (86) 11.5 5.2

J350 8J3350FHX Old Style 9-1/2 (241) 7 (178) 4-1/2 (114) 4 (102) 16.7 7.6

J450 8J1450FHX Old Style 11-1/4 (286) 9 (229) 5-3/16 (132) 5-1/8 (130) 31.2 14.2

J550 7J9550FHX Old Style 13 (330) 11 (279) 6-1/8 (156) 6-3/8 (162) 50.2 22.7

TYPE 13OLD STYLE FLARE

FLARE TOOTH DIMENSIONS - Inches (mm) WEIGHT


J225 6Y3222F Standard 5-3/4 (146) 4-5/8 (117) 3-3/16 (81) 2-5/8 (67) 5.9 2.7

J300 1U3302FHX Standard 7-1/2 (191) 6 (152) 3-7/8 (98) 3-3/8 (86) 10.4 4.7

J350 1U3352FHX Standard 9-1/2 (241) 7 (178) 4-1/2 (114) 4 (102) 18.1 8.2

J400 7T3402F Standard 10-5/16 (262) 8-1/4 (210) 4-15/16 (125) 4-11/16 (119) 25.6 11.6

J450 1U3452FHX Standard 11-1/4 (286) 9 (229) 5-3/16 (132) 5-1/8 (130) 34.5 15.6

J550 1U3552FHX Standard 13-3/4 (349) 11 (279) 6-1/8 (156) 6-5/16 (160) 65.0 29.5

J600 6I6602F Standard 16 (406) 12-1/2 (317) 7-1/4 (184) 7-5/8 (194) 89.0 40.4

FLARE TOOTH DIMENSIONS - Inches (mm) WEIGHT

A

B D

C

C

B

A

D

TYPE 14STANDARD FLARE

58

TOOTH WITH CARBIDE TOOTH WITH CARBIDE GROOVES ONLY

A B C D LBS. KGS.

J300 125-8302HX w/carbide 8-3/4 (222) 2-3/4 (70) 4-3/16 (106) 3-7/16 (87) 13.0 5.9

J350 100-3130HX w/carbide 9-7/8 (251) 3-1/2 (89) 4-7/16 (113) 4 (102) 19.0 8.6

J350 100-3130CG grooves only 17.0 7.7

J400 116-7402HX w/carbide 11 (279) 4 (102) 5-3/32 (129) 4-3/4 (121) 25.9 11.8

J400 116-7402CG grooves only 24.6 11.2

J450 101-9054HX w/carbide 12-1/2 (317) 4-1/2 (114) 5-3/8 (136) 5-3/16 (132) 39.3 17.8J460

J450 101-9054CG grooves only 37.5 17.0J460

J550 101-9055TC w/carbide 13-3/4 (349) 5-3/4 (146) 6-1/8 (156) 6-1/4 (159) 60.0 27.2


TUNGSTEN CARBIDED TEETH DETAILS - Inches (mm)

HEAVY LONGABRASION ACE

TEETH WITH TUNGSTEN CARBIDE

CAT TOOTHSERIES PART NO. DESCRIPTION

59

TUNGSTEN CARBIDED TEETH DETAILS cont'd. - Inches (mm)



J350 4T2353RP2TC w/carbide 11-11/16 (297) 3-3/4 (95) 4-25/32 (121) 4 (102) 26.5 12.0

J350 4T2353RP2CG grooves only 25.0 11.3

J400 7T3403RP2TC w/carbide 13 (330) 4-1/8 (105) 5-1/4 (133) 4-23/32 (120) 34.5 15.6

J400 7T3403RP2CG grooves only 32.5 14.7

J450 9W1453RP2TC w/carbide 13-13/16 (351) 4-27/32 (123) 5-21/32 (144) 5-1/4 (133) 47.0 21.3

J460

J450 9W1453RP2CG grooves only 45.0 20.4

J460

J550 9W1553RP2TC w/carbide 14-3/4 (375) 5-5/32 (131) 6-1/16 (154) 6-1/4 (159) 56.0 25.4

J550 9W1553RP2CG grooves only 56.0 25.4


ROCK PENETRATORABRASION ACE

60

TUNGSTEN CARBIDED TEETH DETAILS cont'd. - Inches (mm)



J300 135-9300RTC w/carbide 10-5/16 (262) 3-1/16 (78) 4-1/4 (108) 3-3/4 (95) 25.0 11.4

J300 135-9300RHX grooves only

J350 144-1358RTC w/carbide 11-3/8(289) 3-5/16 (84) 4-7/16 (113) 4-3/32 (104) 25.5 11.6


J400 135-9400RTC w/carbide 12-5/16 (313) 4 (102) 5-1/4 (133) 4-7/8 (124) 39.0 17.7


J460 138-6451RTC w/carbide 13-3/4 (349) 4-3/4 (121) 5-3/4 (146) 5-1/2 (140) 50.5 22.9


J550 138-6552RTC w/carbide 15 (381) 5-1/4 (133) 6-1/2 (165) 6-3/8 (162) 67.0 30.4


J600 135-9600RTC w/carbide 17-5/8 (447) 6-11/16 (170) 8 (203) 7-3/4 (197) 122.7 55.7



HEAVY DUTY PENETRATORABRASION ACE

MISCELLANEOUS ADAPTER DETAILS - Inches (mm)

Skid-Steer Bolt-On Adapter

132-4720-J200HXwt.= 7.6 lbs. 3.4 kgs.

12O

22.5O

2-5/32

(55)

2-3/8

(60)

25/32 (20)

2-5/8

(67)

11/16 (17)

Dia.

Fits Cat® 226 series skid steer loaders.Uses (1) 5/8 X 3 hex head bolt w/lock nut and (1) 5/8 X 2-1/2 hex head bolt w/locknut.

61

MISCELLANEOUS TOOTH DETAILS - Inches (mm)

1 pc. Bolt-On Tooth

132-4720HXwt.= 4.6 lbs. 2.1 kgs.

Direct replacement for Cat® 132-4720 tooth. FitsCat®216,226,236 and 246 series skid steer loaders.Uses (1) 11/16 X 2-1/4 hex head bolt w/lock nut and(1) 11/16 X 2 hex head bolt w/lock nut.

138-6410HXwt.= 2.6 lbs. 1.2 kgs.

135-9390HXwt.= 3.6 lbs. 1.6 kgs.

Direct replacement for Cat® 138-6410 tooth. FitsCat® 301.5 mini-excavators. Uses (2) 1/2 X 1-1/2hex head bolts w/lock nut.

Direct replacement for Cat®135-9390 tooth.Fits Cat® 302.5 mini-excavators. Uses (2)5/8 X 2 hex head bolts w/lock nut.

PINPART NO. A B (Dia.) LBS. KGS.8J1433P 3-1/4 (83) 3/4 (19) .1 .05

7J9600P 5 (127) 1(25) 1.0 0.5

6J8811P 4-3/8 (111) 1-1/4 (32) 1.4 0.6

3G0500P 6 (152) 1-1/4 (32) 1.8 0.8

6Y2443P 6-1/8 (156) 1-3/8 (35) 2.5 1.1

SINGLE PIECE SNAP RING PIN


REPLACEMENT FASTENER DETAILS - Inches (mm)

A B (Diameter of actualpin - not snap ring)

Asphalt Knife

1U3202KNIFEwt.= 18.2 lbs. 8.3 kgs.

This tool is designed to be used on RTB's and smallexcavators which are running the Cat® style 1U3202teeth. The knife is mounted in place of a 1U3202tooth with the standard fastener.

1 pc. Bolt-On Tooth

1 pc. Bolt-On Tooth

62

REPLACEMENT FASTENER DETAILS cont'd. - Inches (mm)

PINPART NO. A B (Dia.) LBS. KGS.9W7112P 2-5/16 (59) 7/16 (11) 0.1 0.04

6Y3228P 2-5/8 (67) 9/16 (14) 0.1 0.04

9J2258P 3-1/8 (79) 9/16 (14) 0.1 0.04

9J2308P 3-5/8 (92) 9/16 (14) 0.2 0.09

9J6583P 3-7/16 (87) 3/4 (19) 0.3 0.1

9W2678P 4-3/16 (106) 3/4 (19) 0.5 0.2

9J2358P 4-1/4 (108) 3/4 (19) 0.5 0.2

6Y2527P 5-1/4 (133) 3/4 (19) 0.6 0.3

7T3408P 4-5/8 (117) 7/8 (22) 0.6 0.3

8E0468P 5-1/4 (133) 15/16 (24) 1.0 0.4

6Y3394P 4-15/16 (125) 1 (25) 1.1 0.5

6Y8558P 6-3/8 (162) 1 (25) 1.2 0.5

6Y3909P 5-5/8 (143) 1-1/4 (32) 1.9 .9

6I6608P 7-5/8 (194) 1-1/8 (29) 2.3 1.0

8E2229P 6-5/16 (160) 1-3/8 (35) 2.6 1.2

4T4708P 7-11/16 (195) 1-1/4 (32) 2.7 1.7

PIN

A B

A

B

C

TWO PIECE PIN & WASHER SYSTEM

MISCELLANEOUS PINS

3-25/32 (96)3/4 Dia. (19)

21/32 (16)21/32 (16)

1/2 Dia. (13) 2 Holes 1-3/4 Dia. (44)

6-1/2 (165)

Used on 9J6586HX Ripper Shank (see page 18 & 20)

7K9535Pwt.= 0.4 lbs. 0.2 kgs.

2K6413Pwt.= 4.2 lbs. 1.9 kgs.

Used on Compactor Feet (see page 4)

Requires (2) 3B5325P(3 X 15/32) cotter keys.

DIMENSIONS - Inches (mm) WEIGHTPIN

PART NO. A (O.D.) B (I.D.) C LBS. KGS.4T0001W 3/4 (19) 13/32 (10) 9/32 (7) 0.1 0.05

3G9609W 1-1/8 (29) 17/32 (13) 11/32 (9) 0.1 0.05

*3G9609WHR 1-1/8 (29) 17/32 (13) 11/32 (9) 0.1 0.05

6Y9459W 1-1/2 (38) 23/32 (18) 11/32 (9) 0.1 0.05

*6Y9459WHR 1-1/2 (38) 23/32 (18) 11/32 (9) 0.1 0.05

7T3409W 1-9/16 (40) 27/32 (21) 11/32 (9) 0.2 0.09

*7T3409WHR 1-9/16 (40) 27/32 (21) 11/32 (9) 0.2 0.09

8E0469W 1-11/16 (43) 29/32 (23) 11/32 (9) 0.2 0.09

*8E0469WHR 1-11/16 (43) 29/32 (23) 11/32 (9) 0.2 0.09

8E5559W 2 (51) 31/32 (25) 11/32 (9) 0.2 0.09

6I6609W 2-1/4 (57) 1-5/32 (29) 5-16 (8) 0.3 0.14

4T4707W 2-1/2 (64) 1-7/32 (31) 3/8 (10) 0.4 0.19

1012874W 2-11/16 (68) 1-11/32 (34) 3/8 (9) 0.5 0.23

STEEL WASHER

* Harder Rockwell


2-15/16 (75)3/4 Dia. (19)

7K9937Pwt.= 0.4 lbs. 0.2 kgs.

Flex Pin for Ripper Teeth (see page 19)

5J9000Pwt.= 0.7 lbs. 0.3 kgs.

63

ADAPTER DETAILS - Inches (mm)

BOLT-ON CORNER ADAPTERS for LOADERS

C

A

D

EO

HENSLEY CAT TOOTHPART NO. SERIES A B C D E LBS. KGS. SIZE *ASSY. NO. QTY.

3G4258HX (LH)& J250 5-3/4 (146) 4-3/16 (106) 1-1/16 (27) 3 (76) 43O 25.0 ea. 11.3 ea 1 X 3-1/4 AC10-314 1 ea.

3G4259HX (RH)

3G4308HX (LH)& J300 7 (178) 4-3/4 (121) 1-1/16 (27) 4-1/16 (103) 39O 34.9 ea. 15.8 ea. 1-1/4 X 4 AC114-400 1 ea.

3G4309HX (RH)

3G8308HX (LH)& J300 8 (203) 5-1/2 (140) 1-9/16 (40) 5-1/8 (130) 47O 35.9 ea. 16.3 ea. 1-1/4 X 4 AC114-400 1 ea.

3G8309HX (RH)

1U1358HX (LH)& J350 9-1/8 (232) 5-3/4 (146) 1-5/8 (41) 5-7/8 (149) 45O 49.7 ea. 22.5 ea. 1-1/4 X 4 AC114-400 1 ea.

1U1359HX (RH)

3G5358HX (LH)& J350 8-17/32 (217) 5-5/8 (143) 1-9/16 (40) 5-3/32 (129) 38O 51.3 ea. 23.3 ea. 1-1/4 X 4 AC114-400 1 ea.

3G5359HX (RH)

C

A

FO

EO

3 HOLE BOLT-ON ADAPTERS for LOADERSHENSLEY CAT TOOTHPART NO. SERIES A B C D E F LBS. KGS. SIZE *ASSY. NO. QTY.

8J5307HX J300 3-3/8 (86) 5-3/4 (146) 1-5/16 (33) 3-1/4 (83) 23O 17O 30.6 13.8 1 X 4-1/4 A10-414 3

3G1357HX J350 3-3/8 (86) 5-3/4 (146) 1-5/16 (33) 3-1/4 (83) 23O 16O 38.4 17.4 1 X 4 AC10-400 3

3G2357HX J350 4-5/32 (106) 6-1/8 (156) 1-13/16 (46) 3-1/4 (83) 20O 15O 46.0 20.9 1 X 4-1/2 AC10-412 3

DIMENSIONS - Inches (mm) PLOW BOLTS

Plow Bolt

D

(RH Shown, LH Opposite)

Plow Bolts

B

14O


WEIGHT


B

64

HENSLEY CAT TOOTHPART NO. SERIES A B C E F LBS. KGS. SIZE *ASSY. NO. QTY.

9W6207HX J200 1-31/32 (50) 2-15/16 (75) 7/8 (22) 23O 14O 4.8 2.2 5/8 X 2-1/2 A58-212 2

1U4207HX J200 2-5/8 (67) 3-1/2 (89) 13/16 (21) 30O 14O 8.5 3.9 3/4 X 3 A34-300 2

1U257HX J250 2-3/4 (70) 4-7/8 (124) 1-1/16 (27) 23O 14O 18.0 8.2 1 X 3-3/4 AC10-334 2

8J6656HX J250 2-3/4 (70) 4-7/8 (124) 1-1/16 (27) 27O 13O 18.4 8.3 1 X 4 A10-400 2

1U307HX J300 2-3/4 (70) 4-7/8 (124) 1-1/16 (27) 23O 14O 25.4 11.5 1 X 4 A10-400 2

8J6587HX J300 2-3/4 (70) 4-7/8 (124) 1-1/16 (27) 23O 15O 27.5 12.5 1 X 4 A10-400 2

4T4307HX J300 3-3/16 (81) 6-1/2 (165) 1-5/16 (33) 23O 14O 29.3 13.3 1 X 4-1/4 AC10-414 2

3G9307HX J300 3-3/8 (86) 6-5/16 (160) 1-5/16 (33) 23O 14O 31.9 14.5 1-1/4 X 4-1/2 AC114-412 2

3G3357HX J350 3-7/8 (98) 5-7/8 (149) 1-11/16 (43) 24O 14O 43.9 19.9 1-1/4 X 5 AC114-500 2

3G7357HX J350 3-3/8 (86) 6-9/32 (159) 1-5/16 (34) 22O30' 15O 46.2 20.9 1-1/4 X 4-1/4 AC114-414 2

1U1357HX J350 4-1/32 (102) 6-1/8 (156) 1-13/16 (46) 20O 14O 44.7 20.3 1-1/4 X 5 AC114-500 2

6I9898HX J400 4-3/16 (106) 6-1/8 (156) 1-13/16 (46) 22O30' 14O 62.0 28.1 1-1/4 X 5 AC114-500 2

PLOW BOLTS

2 HOLE BOLT-ON ADAPTERS for LOADERSDIMENSIONS - Inches (mm)

ADAPTER DETAILS cont'd. - Inches (mm)

WEIGHT


A B

CEO

FO Plow Bolts

65

HENSLEY CAT TOOTH TYPEPART NO. SERIES A B C E F LBS. KGS.

1U1254HXC J250 1 9-1/4 (235) 2 (51) 1 (25) 22O 13O 14.3 6.5

1U1304HXC J300 1 9-3/8 (238) 2-5/16 959) 1-1/16 (27) 22O 14O 19.4 8.8

1U1354HXC J350 1 11-1/4 (286) 3-3/16 (81) 1-1/2 (38) 22O 14O 31.7 14.4

1U1355HXR& J350 2 11-3/4 (298) 3-3/4 (95) 1-1/2 (38) 22O 14O 41.2 ea. 18.7 ea.

1U1356HXL

107-3404HX J400 1 11-1/2 (292) 3-1/4 (83) 1-1/2 (38) 22O 14O 45.0 20.4

9J9584HXC2 J450 1 12-1/2 (318) 4-1/8 (105) 2-3/16 (56) 23O 13O 56.7 25.7

9J9585HXR2& J450 2 13-3/4 (349) 4-1/8 (105) 2-3/16 (56) 23O 13O 64.6 ea. 29.3

9J9586HXL2

8E0464HXC J460 1 12-1/2 (318) 4-1/8 (105) 2-3/16 (56) 23O 13O 57.0 25.9

8E0465HXR& J460 2 13-3/4 (349) 4-1/8 (105) 2-3/16 (56) 23O 13O 64.0 ea. 29.0 ea.

8E0466HXL

3G4554HXC J550 1 14-7/8 (378) 5 (127) 2-11/16 (68) 23O 14O 80.6 36.6

3G4555HXR& J550 2 15-5/8 (397) 5 (127) 2-11/16 (68) 23O 14O 87.8 ea. 39.8 ea.

3G4556HXL

CURRENT FLUSH MOUNT WELD-ON ADAPTERS for LOADERS

AB

CEO


HENSLEY CAT TOOTH TYPEPART NO. SERIES A B C E F LBS. KGS.

8J4254HXC J250 8-1/8 (206) 1/2 (13) 3/8 (10) 21O 15O 11.8 5.3

9J4304HXC J300 8-15/16 (227) 1-1/8 (29) 11/16 (17) 22O 15O 20.3 9.2

9J4354HXC J350 9-15/16 (252) 1-11/16 (43) 1 (25) 22O 15O 30.4 13.8

7J9554HXC J550 11-7/16 (290) 1-15/16 (49) 1-1/8 (29) 23O 17O 72.9 33.1


"OLD STYLE" FLUSH MOUNT WELD-ON ADAPTERS for LOADERS

AB

C

EO

AB

C

TYPE 1(Center)

TYPE 2(RH Shown, LH Opposite)

FO

15O

FO

EO

FO


WEIGHT

WEIGHT

66



TYPE 2(Center)

TYPE 1(RH & LH Universal)

GO

AB

C

D

FO

EO

AB

C

D

EO

FO

AB

D

EO C

FO

15O

HENSLEY CAT TOOTH TYPEPART NO. SERIES A B C D E F G LBS. KGS.

2740-416 J200 2 5 (127) 2-5/8 (67) 1-3/32 (28) 7/32 (6) 30O 12O 3.5 1.6

125-446 J225 2 7-1/2 (191) 5 (127) 1-5/16 (33) 3/8 (10) 30O 12O 11.1 5.0

125-8404HX J400 2 10 (254) 7 (178) 1-27/32 (47) 23/32 (18) 22O 15O 43.9 19.9

125-8405HX& J400 3 10-7/16 (265) 7-7/16 (189) 1-27/32 (47) 23/32 (18) 22O 15O 15O 46.2 ea. 20.9 ea.

125-8406HX

4T8454CHX 2 53.0 24.0& J450 11-1/2 (292) 6-3/4 (171) 1-7/8 (48) 13/16 (21) 22O 15O

4T8455RLHX 1 12O 55.0 24.9

9J6698HXC J450 2 11-3/8 (289) 7-7/8 (200) 2-1/8 (54) 5/8 (16) 22O 15O 52.0 23.6

9J6701HXR& J450 3 12-1/2 (318) 9 (229) 2-1/8 (54) 3/4 (19) 22O 15O 57.0 ea. 25.9 ea.

9J6702HXL

8E3464HXC J460 2 10-3/8 (264) 6-7/8 (175) 2-1/8 (54) 3/4 (19) 22O 12O 50.0 22.7

8E3465HXR& J460 3 12-1/2 (318) 9 (229) 2-1/8 (54) 3/4 (19) 22O 12O 55.0 ea. 24.9 ea.

8E3466HXL

303J460 J460 2 12-3/4 (324) 9-3/4 (248) 2-5/8 (67) 5/8 (16) 30O 12O 70.0 31.8

4T7554CHX 2 65.0 29.5& J550 12-1/2 (318) 8 (203) 2-1/16 (52) 13/16 (21) 23O 15O

4T7555RLHX 1 15O 68.0 30.8

3G9494HXC J550 2 14-1/4 (362) 12-5/8 (321) 2-5/8 (67) 1-1/16 (27) 22O 15O 76.5 34.7

3G9495HXR& J550 3 15 (381) 13-3/8 (340) 2-5/8 (67) 1-1/16 (27) 22O 15O 81.7 ea. 37.1 ea.

3G9496HXL

9W9704HXC J700 2 17-3/16 (437) 13-11/16 (347) 2-5/8 (67) 1 (25) 22O 15O 164.0 74.4

9W9705HXR& J700 3 17-1/2 (445) 14 (356) 2-5/8 (67) 1 (25) 22O 15O 15O 175.0 ea. 79.4 ea.

9W9706HXL

4T4704HXC J700 2 18-1/8 (460) 13-1/8 (333) 3-1/16 (78) 1 (25) 22O 15O 164.0 74.4

4T4705HXR& J700 3 18-1/8 (460) 13-1/8 (333) 3-1/16 (78) 1 (25) 22O 15O 15O 172.0 78.0

4T4706HXL

WRAP-AROUND WELD-ON ADAPTERS for LOADERSDIMENSIONS - Inches (mm) WEIGHT

67

WRAP-AROUND WELD-ON ADAPTERS for LOADERS


TYPE 3

TYPE 4

TYPE 1WITH TUNGSTEN CARBIDE

TYPE 2WITH TUNGSTEN CARBIDE

RIGHT HAND SHOWNLEFT HAND OPPOSITE

RIGHT HAND SHOWNLEFT HAND OPPOSITE

HENSLEY CAT TOOTH TYPEPART NO. SERIES A B C D E F LBS. KGS.

107-3554HX J550 3 14-1/2 (368) 12-1/2 (305) 2-5/8 (67) 1 (25) 22O 15O 92.0 41.7

107-3555HX(RH)& J550 4 14-1/2 (368) 12-1/2 (317) 2-5/8 (67) 1 (25) 22O 15O 97.0 44.0

107-3556HX(LH)

112-2554HX J550 1 14-1/2 (368) 12-1/2 (305) 2-5/8 (67) 1 (25) 22O 15O 94.0 42.6

112-2555HX (RH)& J550 2 14-1/2 (368) 12-1/2 (305) 2-5/8 (67) 1 (25) 22O 15O 98.0 44.5

112-2556HX (LH)

119-8604HX J600 3 14-1/2 (368) 12-1/2 (305) 2-7/8 (73) 1-3/16 (30) 22O 15O 156.0 70.8

119-8605HX (RH)& J600 4 14-1/2 (368) 12-1/2 (305) 2-7/8 (73) 1-3/16 (30) 22O 15O 169.0 76.7

119-8606HX (LH)

119-8607HX J600 1 14-1/2 (368) 12-1/2 (305) 2-7/8 (73) 1-3/16 (30) 22O 15O 158.0 71.7

119-8608HX (RH)& J600 2 14-1/2 (368) 12-1/2 (305) 2-7/8 (73) 1-3/16 (30) 22O 15O 171.0 77.6

119-8609HX (LH)


68


TYPE 2(Center)



WRAP-AROUND WELD-ON ADAPTERS for BACKHOES & EXCAVATORS

HENSLEY CAT TOOTH TYPEPART NO. SERIES A B C D E F H J LBS. KGS.

119-3204HX J200 2 3-1/4 (83) 4-1/4 (108) 1-1/8 (29) 1/2 (13) 22O 9O 4.1 1.9

6Y3224HX J225 2 5-9/16 (141) 3-11/16 (94) 1-1/16 (27) 7/16 (11) 22O 8O 7.3 3.3

6Y3254HX J250 2 6-1/8 (156) 5 (127) 1-5/16 (33) 3/8 (10) 22O 9O 11.2 5.1

9W1304HX J300 2 7-1/2 (191) 5-1/4 (133) 1-5/16 (33) 7/16 (11) 22O 9O 17.3 7.8

8E9490HX J300 2 8-1/4 (210) 5-7/8 (149) 1-9/16 (40) 1/2 (13) 23O 12O 17.2 7.8

3G6304HXC J300 2 8 (203) 4-9/16 (116) 1-5/16 (33) 9/16 (14) 22O 8O 18.0 8.2

3G6305HXR& J300 3 8 (203) 4-9/16 (116) 1-5/16 (33) 9/16 (14) 22O 8O 1-7/16 (37) 1-7/8 (48) 17.5 ea. 7.9 ea.

3G6306HXL

3G8354HXC J350 2 8-1/4 (210) 4-3/4 (121) 1-11/16 (43) 5/8 (16) 35O 8O 20.9 9.5

3G8355HXR& J350 3 8-1/4 (210) 4-3/4 (121) 1-11/16 (43) 5/8 (16) 35O 8O 1-3/4 (44) 1-5/16 (33) 19.6 ea. 8.9 ea.

3G8356HXL

6I6354HX J350 2 9 (229) 7-1/4 (184) 1-5/8 (41) 9/16 (14) 22O 12O 27.2 12.3

7T3404HXC J400 2 9-1/2 (241) 6-3/4 (171) 1-7/8 (48) 3/4 (19) 22O 9O 33.5 15.2

8J9141HXC J450 2 11-1/8 (283) 7-3/8 (187) 2 (51) 7/16 (11) 24O 9O 46.5 21.1

8J9139HXR& J450 3 11-1/8 (283) 7-3/8 (187) 2 (51) 7/16 (11) 24O 9O 2-1/8 (54) 3-1/2 (89) 46.5 ea. 21.1 ea.

8J9140HXL

8E6464HXC J460 2 11-1/8 (283) 7-3/8 (187) 2 (51) 7/16 (11) 24O 9O 46.5 21.1

8E6465HXR& J460 3 11-1/8 (283) 7-3/8 (187) 2 (51) 7/16 (11) 24O 9O 2-1/8 (54) 3-1/2 (89) 46.5 ea. 21.1 ea.

8E6466HXL

6I6554HXC J550 2 13-1/4 (337) 11 (279) 2-9/16 (65) 1-1/16 (27) 22O 9O 77.0 34.9

9J0174HXC J550 2 14-1/2 (368) 8-5/8 (219) 2-7/16 (62) 7/8 (22) 23O 9O 77.2 35.0

9J0172HXR& J550 3 14-1/2 (368) 10 (254) 2-7/16 (62) 7/8 (22) 23O 9O 2-3/16 (56) 3-3/8 (86) 78.2 ea. 35.5 ea.

9J0173HXL

6I6604HXC J600 2 14-1/2 (368) 12 (305) 3-1/8 (78) 1-3/8 (35) 22O 9O 126.0 57.1

132-4705RHX& J700 4 14-1/2 (368) 12 (305) 3-1/8 (78) 1-3/8 (35) 22O 9O 135.0 61.2

132-4706LHX

WEIGHTDIMENSIONS - Inches (mm)


69

WELD-ON NOSES

WELD-ON CAT TOOTHPART NO. SERIES A B C D LBS. KGS.

8J7525WN J200 2-5/16 (59) 2-1/4 (57) 15/16 (24) 7/16 (11) 2.5 est. 1.1 est.

6Y3224WN J225 3-3/16 (81) 2-9/16 (65) 1-1/8 (29) 7/16 (11) 3.8 est. 1.7 est.

9J4254WN J250 3-1/4 (83) 2-3/4 (70) 1-1/8 (29) 1/2 (13) 5.1 2.3

9J4304WN J300 3-1/2 (89) 3-1/2 (89) 1-1/2 (38) 7/8 (22) 8.8 3.9

9J4354WN J350 4-3/8 (111) 4 (102) 1-1/4 (32) 1/2 (13) 10.7 4.8

7T3404WN J400 5 (127) 4-5/8 (117) 1-3/8 (35) 1/2 (13) 15.2 6.9

3G4454WN J450 5-1/8 (130) 5 (127) 1-1/2 (38) 1/2 (13) 19.3 8.8

*8E6464WN J460 5-1/8 (130) 5 (127) 1-1/2 (38) 1/2 (13) 19.8 9.0

9J4554WN J550 5-1/2 (140) 5-3/4 (146) 1-3/4 (44) 3/4 (19) 29.6 13.4

6I6604WN J600 7-1/8 (181) 7-5/8 (194) 1-7/8 (48) 13/16 (21) 53.0 24.0

* Larger pin hole diameter for oversize fastener


ADAPTER DETAILS con't. - Inches (mm)

TYPE 2(Center)


BOTTOM LEG WELD-ON ADAPTERSADAPTER CAT TOOTHPART NO. SERIES TYPE A B C D E F LBS. KGS.

8J7525HX J200 3 3-15/16 (100) 1 (25) 1 (25) 1/4 (6) 23O 14O 3.1 1.4

3G0169HX J250 3 7-1/2 (191) 2-5/16 (59) 2 (51) 5/16 (8) 22O 15O 11.7 5.3

1U1350CHX 2 30.7 14.7& J350 10 (54) 7 (178) 1-13/16 (46) 11/16 (17) 22O 14O

1U1351RLHX 1 32.5 14.7


TYPE 3(Center)

6I6555HXR (Right Hand Opposite)6I6556HXL (Left Hand Shown)

wt.= 81.3 lbS. 36.9 kgs.

70

EXCAVATOR SIDECUTTER DETAILS - Inches (mm)

7Y0358LHX (LH Shown) 7Y0357RHX (RH Opposite) wt.= 40.9 lbs. 18.6 kgs. eachEach Requires (3) 1 X 3 Plow Bolts*Plow Bolt Assembly No. A10-300

9J9540LHX (LH Shown) 9J9539RHX (RH Opposite) wt.= 58.0 lbs. 26.3 kgs. eachEach Requires (3) 1 X 3 Plow Bolts*Plow Bolt Assembly No. A10-300

9J1855HXR (RH Shown) 9J1856HXL (LH Opposite) wt.= 31.0 lbs. 14.0 kgs. eachEach Requires (3) 3/4 X 2-1/2 Plow Bolts

*Plow Bolt Assembly No. A34-212

1-7/16 (37)

13/16 (21)

3-1/8(79)

3-1/8(79)

4 (102)

11-1/8 (283)

13-5/8 (346)


71

EXCAVATOR SIDECUTTER DETAILS cont'd. - Inches (mm)

8J9614HXL (LH Shown) 8J9615HXR (RH Opposite) wt.= 49.0 lbs. 22.2 kgs. eachEach Requires (3) 1 X 3 Plow Bolts*Plow Bolt Assembly No. A10-300

1-5/8 (41)

15/16 (24)

3-15/16(100)

3-15/16(100)

5-1/4(133)

14-1/8(359)

11-7/8 (302)

2 (51)

1-1/8 (29)

16(406)

2 (51)

4 (102)

2(51)

2(51)

2(51)

2(51)

12-1/2 (318)

8J9825HXR (RH Shown) 8J9826HXL (LH Opposite) wt.= 68.0 lbs. 30.8 kgs. each Each Fastens With (5) 1 X 3-1/2 Plow Bolts

*Plow Bolt Assembly Part No. A10-312


72

4T6664PHX wt.= 44.8 lbs. 20.3 kgs. Used With 8J9825HXR & 8J9826HXLRequires (4) 1 X 3-1/2 Plow Bolts

*Plow Bolts Assembly No. A10-312

EXCAVATOR SIDECUTTER COMBINATION PLATE DETAILS - Inches (mm)

23-1/2 (597) 1 (25)

10(254)

4T2886BHX wt.= 31.0 lbs. 14.1 kgs. Used With 8J9615HXR & 8J9614HXLRequires (4) 3/4 X 3-1/4 Plow Bolts*Plow Bolt Assembly No. A34-314

3/4 (19)18-5/8 (473)

9-7/8(251)

4T2963-4HX wt.= 18.5 lbs. 8.4 kgs. Used With 9J1855HXR & 9J1855HXLRequires (4) 5/8 X 2-3/4 Plow Bolts*Plow Bolt Assembly No. A58-234


73

MACHINEMODEL TOOTH PIN

920922 4K50-HX 3K2P R2R933 (Long) (rubber plug)941

930, 941,944, 950, 4K34HX 4K43P 4K41LK951, 955, (Long)

966

950966 4K6148HX 4K32P 4K8LK977 (Long)980

977 2K4569HX 4K32P 4K8LK

TEETH FASTENERSRUBBER

LOCK

4K34HXwt.= 4.6 lbs. 2.1 kgs.

4K50HXwt.= 5.0 lbs. 2.3 kgs.

4K6148HXwt.= 7.4 lbs. 3.4 kgs.

VERTICAL LOCK TEETH &FASTENERS for LOADERS

2K4569HXwt.= 5.7 lbs. 2.6 kgs.

74

PINPART NO. A B C LBS. KGS.

4K43P 2-11/16 (44) 3/4 (19) 5/16 (8) 0.1 0.05

4K32P 3-1/8 (79) 13/16 (21) 7/16 (11) 0.3 0.14


A

B

C

A C

RUBBER LOCKPART NO. A B C LBS. KGS.

4K41LK 1-3/4 (68) 31/32 (25) 1/2 (13) 0.1 0.05

4K8LK 1-31/32 (50) 1-1/16 (27) 9/16 (14) 0.2 0.09

RUBBERLOCK

PIN

B


WEIGHT

3K1P(uses R2R rubber plug)wt.= 0.1 lbs. 0.05 kgs.

3K2P(uses R2R rubber plug)wt.= 0.2 lbs. 0.09 kgs.

VERTICAL LOCK TEETH &FASTENERS for LOADERS

75

CAST LIPS FOR RTBs

12MCAT-12A-HXwt.= 35.3 lbs. 16.0 kgs.

J200 TOOTH SERIESstd. tooth: 1U3202HX (see page 52)

18MCAT-12A-HXwt.= 46.6 lbs. 21.2 kgs.

J200 TOOTH SERIESstd. tooth: 1U3202HX (see page 52)

24MCAT-12A-HXwt.= 62.0 lbs. 28.1 kgs.J200 TOOTH SERIES

std. tooth: 1U3202HX (see page 52)

side view for all cast lips

76

TOOTH/MACHINE QUICK REFERENCEGUIDE

CATTOOTH

SERIES

STANDARDTOOTH

BACKHOELOADERS

EARLYMODEL

EXCAVATORS

NEWERMODEL

EXCAVATORS

WHEELLOADERS

CRAWLERLOADERS SCRAPERS

416, 426, 428, 416, 426, 428, 931, 935436, 438, 436, 438, 910,

(also D3/931 910E, F, 914Gbackhoe att.)

446 E70 307 446, 933

205, 206, 211, 311, 312 IT12, IT14, IT24F 941, 943, 951 613212, 213, 214, IT26, IT28, IT38,E110, E120B 916, 918F, 920,

930, 936E, F;938F, 939

215, 219, 224, 315, 320A, B 944, 950, 950B, 953, 953B, C; 615, 619, J621,E180, E200, 950E, F; 960F, G 955L, 963, 623

EL200 962G, 966, 966C 963B

225, 229, E240 320A, B; 322A, 966D, E, F, G 963B, 973, 977 633, 639322B, 325A, B 970F, 972G, 980,

980B,C, F

229 322A, B; 325A 980F, G325B, 330A, B

231, 235, 235B, 330A, B; 345B 988, 988B, 988F 983235C, E300 350

245, 245B 345B, 350 988G, 990, 992, 992B, 992C, D

375 992D, 992G

375 992D, G; 994

J200 1U3202HX

J225 6Y3222HX

J250 1U3252HX

J300 1U3302HX

J350 1U3352HX

J400 7T3402HX

J450/J460 9W8452HX

J550 9W8552HX

J600 6I6602HX

J700 4T4702HX

77

PLOW BOLTS

PLOW BOLT ASSEMBLIES* DIMENSIONS

w/HexNut

StockNo.

w/HexCone Nut

StockNo.

BoltLength

Diameterw/ Threads

per Inch

A58-200 75-1090 . . . . . . . . . . . . . . . . . . 5/8" 11 2"A58-214 75-1100 . . . . . . . . . . . . . . . . . . 5/8" 11 2-1/4"A58-212 75-1110 . . . . . . . . . . . . . . . . . . 5/8" 11 2-1/2"A58-234 75-1120 . . . . . . . . . . . . . . . . . . 5/8" 11 2-3/4"A58-300 75-1130 . . . . . . . . . . . . . . . . . . 5/8" 11 3"A58-312 75-1140 . . . . . . . . . . . . . . . . . . 5/8" 11 3-1/2"

A34-212 75-1200 . . . . . . . . . . . . . . . . . . 3/4" 10 2-1/2"A34-234 75-1210 . . . . . . . . . . . . . . . . . . 3/4" 10 2-3/4"A34-300 75-1220 . . . . . . . . . . . . . . . . . . 3/4" 10 3"A34-314 75-1230 . . . . . . . . . . . . . . . . . . 3/4" 10 3-1/4"A34-312 75-1240 . . . . . . . . . . . . . . . . . . 3/4" 10 3-1/2"A34-334 75-1250 . . . . . . . . . . . . . . . . . . 3/4" 10 3-3/4"A34-400 75-1260 . . . . . . . . . . . . . . . . . . 3/4" 10 4"A34-412 75-1270 . . . . . . . . . . . . . . . . . . 3/4" 10 4-1/2"

A78-300 75-1300 . . . . . . . . . . . . . . . . . . 7/8" 9 3"A78-314 75-1310 . . . . . . . . . . . . . . . . . . 7/8" 9 3-1/4"A78-312 75-1320 . . . . . . . . . . . . . . . . . . 7/8" 9 3-1/2"A78-334 75-1330 . . . . . . . . . . . . . . . . . . 7/8" 9 3-3/4"A78-400 75-1340 . . . . . . . . . . . . . . . . . . 7/8" 9 4"A78-412 75-1350 . . . . . . . . . . . . . . . . . . 7/8" 9 4-1/2"

**A10-212J 75-1490 . . . . . . . . . . . . . . . . . . 1" 8 2-1/2"A10-300 75-1400 AC10-300 72-2400 1" 8 3"A10-314 75-1410 AC10-314 75-2410 1" 8 3-1/4"A10-312 75-1420 AC10-312 75-2420 1" 8 3-1/2"A10-334 75-1430 AC10-334 75-2430 1" 8 3-3/4"A10-400 75-1440 AC10-400 75-2440 1" 8 4"A10-412 75-1450 AC10-412 75-2450 1" 8 4-1/2"A10-500 75-1460 AC10-500 75-2460 1" 8 5"

A114-400 75-1500 AC114-400 75-2500 1-1/4" 7 4"A114-414 75-1510 AC114-414 75-2510 1-1/4" 7 4-1/4"A114-412 75-1520 AC114-412 75-2520 1-1/4" 7 4-1/2"A114-500 75-1530 AC114-500 75-2530 1-1/4" 7 5"A114-512 75-1540 AC114-512 75-2540 1-1/4" 7 5-1/2"A114-700 75-1550 . . . . . . . . . . . . . . . . . . 1-1/4" 7 7"

Hex Nuts

Part No. Stock No. Inside Dia. Description

N10J 75-0730 1" Hex Jam Nut

N58 75-0800 5/8" Hex Nut

N34 75-0810 3/4" "

N78 75-0820 7/8" "

N10 75-0830 1" "

N114 75-0840 1-1/4" "

N10C 75-0930 1" Hex Cone Nut

N114C 75-0940 1-1/4" "

RetainersPart No. Stock No. Inside Dia.

LW58 75-0600 5/8"

LW34 75-0610 3/4"

LW78 75-0620 7/8"

LW10 75-0630 1"

LW114 75-0640 1-1/4"

*Plow Bolt Assembly consists of Plow Bolt with Nut.**Comes w/Hex Jam Nut.

78

NOTES

79

NOTES

80

NOTES

81

NOTES

82

NOTES

83

NOTES

84

YOUR AUTHORIZED HENSLEY DEALER:

WARNINGUnder the Occupational Safety and Health Act of 1970, as well as other applicable industry standards there may be required or recommendsafety and/ or health equipment, devices, requirements, personal protective equipment, etc., that are required to be used by your employeesbefore working on any Hensley Industries product. Please consult with the appropriate regulatory agency or safety officer, before working on

any of our products to determine the applicability of all safety / personal protective equipment /health devices that are or may be required.

All manufacturer's names, numbers, symbols, & descriptions are used for reference purposes only, & it is not implied that any part listed is the productof these manufacturers.

Cat® & Caterpillar® are registered trademarks of Caterpillar, Inc.

Form0504 Rev E. 0306

Hensley Industries, Inc. 2108 Joe Field Rd. Dallas, TX 75229 U.S.A.

www.hensleyind.com

Customer ServiceToll Free U.S./Canada

Ph. (888) 406 - 6262Fax (888) 241 - 3274All Other LocationsPh. (972) 406 - 6262Fax (972) 241-3274

Copyright © 2006 Hensley Industries, Inc.This publication is protected by the copyright laws of the United States. Unauthorized duplication and distribution is prohibited.

HENSLEY J Gavilanes,Cuchillas,Puntas y Adaptadores

Documents

Transcript of HENSLEY J Gavilanes,Cuchillas,Puntas y Adaptadores