Hedge Trimmer - canadiantire.ca€¦ · operate with two Hands Hold and operate the hedge trimmer...

model number 060-3014-6 | contact us: 1.866.523.5218

IMPORTANT:Read and follow all safety rules and operating instructions before using this product.

Instruction Manual

Hedge Trimmer

model no. 060-3014-6 | contact us: 1.866.523.5218

2Ta

ble

of C

onte

nts

Motor: 3.5 ABlade length: 18” (45.7 cm)Cut capacity: 2/3” (1.7 cm)No load speed: 3000 (±10%) SPMWeight: 6 lb (2.7 kg)

SPeCifiCAtioNS 2KNoW YoUR MoWeR 3SYMBolS 4SAfetY RUleS 6exPloded VieW 9PARtS liSt 10eleCtRiCAl 12ASSeMBlY 14oPeRAtioN 15MAiNteNANCe 18WARRANtY 20

Spe

cific

atio

ns

model no. 060-3014-6 | contact us: 1.866.523.5218 model no. 060-3014-6 | contact us: 1.866.523.5218

3

Kno

w Y

our H

edge

Tri

mm

er

1. lock-off button2. Auxiliary handle3. Guard4. Blade support rod5. Blade6. trigger switch7. Cord retainer

3

4

5

12

6

7

1. Cord2. extension cord

12

KNOW YOUR MOWeRthe safe use of this product requires an understanding of the information in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules.

CORD ReTAINeRA convenient cord retainer helps keep the extension cord connection secure during trimmer operation.

GUARDthe guard helps to deflect chips or other debris away from the operator’s hands.

TRIGGeR SWITCH AND LOCK-OFF BUTTONthe trigger switch, located beneath the rear handle, and the lock-off button, located behind the front handle, must be depressed simultaneously to allow blade movement.lock-off switch may be released once hedge trimmer is running.


4

Symbol Name designation/explanation

V Volts Voltage

A Amperes Current

Hz Hertz frequency (cycles per second)

W Watts Power

hrs Hours time

Class ii Construction double-insulated construction

Read the operator’s Manual

to reduce the risk of injury, user must read and understand operator’s manual before using this product.

Wear eyes protection and ears protection

Wear eye protection with side shields that are marked to comply with ANSiZ87.1 when operating this equipment.

Gloves Wear non-slip, heavy-duty protective gloves when handling the hedge trimmer and the blade.

Safety footwear Wear non-slip safety footwear when using this equipment.

Keep Bystanders Away Keep all bystanders at least 50’ (15 m) away.

Hot Surface to reduce the risk of injury or damage, avoid contact with any hot surface.

electric Shock failure to use in dry conditions and to observe safe practices can result in electric shock.

Sharp Blade danger – keep hands and feet away from blade.

operate with two Hands Hold and operate the hedge trimmer properly with two hands.

Moving Parts Keep hands away from moving parts.

Safety Alert Precautions that involve your safety

Ricochet thrown objects can ricochet and result in personal injury or property damage.

Wet Conditions Alert do not expose to rain or use in damp locations.

Sym

bols

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.


5

the following signal words and meanings are intended to explain the levels of risk associated with this product.

Symbol Signal Meaning

dANGeR indicates an imminently hazardous situation, which, if not avoided, could result in death or serious injury.

WARNiNG indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUtioN indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

CAUtioN (Without Safety Alert Symbol) indicates a situation that may result in property damage.

Sym

bols


6

Save all warnings and instructions for future reference.

the term “power tool” in all of the warnings listed below refers to your corded or cordless power tool.

1. Work area safety

A. Keep work area clean and well lit. Cluttered or dark areas invite accidents.B. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.C. Keep children and bystanders away while operating a power tool. distractions can cause you to lose control.

2. electrical safety

A. Power tool plugs must match the outlet. Never modify the plug in any way. do not use any adapter plugs with grounded power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.B. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. there is an increased risk of electric shock if your body is grounded.C. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. damaged or entangled cords increase the risk of electric shock.e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCd reduces the risk of electric shock.

3. Personal safety

A. Stay alert, watch what you are doing and use common sense when operating a power tool. do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.B. Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce the risk of personal injuries.C. Avoid accidental starting. ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

! WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

Gen

eral

Ssf

ety

Rul

es


7

e. Do not overreach. Keep proper footing and balance at all times. this enables better control of the power tool in unexpected situations.f. Dress properly. do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. loose clothes, jewellery, or long hair can be caught in moving parts.G. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust-related hazards.

4. Power tool use and care

A. Do not force the power tool. Use the correct power tool for your application. the correct power tool will do the job better and safer at the rate for which it was designed.B. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.C. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. if damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.G. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5. Service

A. Have your power tool serviced by a qualified repair person using only identical replacement parts. this will ensure that the safety of the power tool is maintained.

Gen

eral

Saf

ety

Rul

es


8

! WARNING: CALIFORNIA PROPOSITION 65 This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals, including lead, known to cause cancer, birth defects or other reproductive harm. Wash hands after handling. Some examples of these chemicals are:

• Lead from lead-based paints• Crystalline silica from bricks and cement and other

masonry products, and• Arsenic and chromium from chemically-treated

lumber.Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

HeDGe TRIMMeR SAFeTY WARNINGS

• Use both hands when operating the hedge trimmer. Using one hand could cause loss of control and result in serious personal injury.

• Keep all parts of the body away from the cutter blade. do not remove cut material or hold material to be cut when blades are moving. Make sure the switch is off when clearing jammed material. Blades coast after turn-off. A moment of inattention while operating the hedge trimmer may result in serious personal injury.

• Carry the hedge trimmer by the handle with the cutter blade stopped. Proper handling of the hedge trimmer will reduce possible personal injury from the cutter blades.

• Hold the power tool by insulated gripping surfaces only, because the cutter blade may contact hidden wiring or its own cord. Cutter blades contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

• Keep cable away from cutting area. during operation the cable may be hidden in shrubs and can be accidentally cut by the blade.

• DANGeR – Keep hands away from blade. Contact with blade will result in serious personal injury.

SAVe THeSe INSTRUCTIONS!

Spe

cific

Ssf

ety

Rul

es


9

exp

lode

d Vi

ew

678 5 4 3 2 191011

12

13 17

16

15

14

19

18


10Pa

rts

List

item description drawing Qty

1 Motor cover housing 31301652-2 1

2 Board 34118441-1 1

3 Screw St3.5*10-C 32201441 2

4 trigger 34106456-2 1

5 Spring 33402161-1 1

6 lock-off spring 32201647 1

7 lock-off button 34109453-11 1

8 4.8 Sheath 34901161 2

9 terminal 4.8*0.8 36503161 2

10 Micro swtich 36303152 1

11 Screw 3220313 10

12 Wiring cap 36504161 1

13 Motor/Blade assembly 31106161 1

14 Screw St4×12-f 3220905 6

15 Guard 34103456-1 1

16 Auxiliary handle assembly 31302162-5 1

17 Screw M4*23 32203162 2

18 Power cord assembly 31105161 1

19 Blade cover 34110648 1


11

ele

ctri

cal

DOUBLe INSULATION

double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. double-insulated tools do not need to be grounded.

eLeCTRICAL CONNeCTION

this product has a precision-built electric motor. it should be connected to a power supply that is 120 V, AC only, (normal household current) 60 Hz. do not operate this product on direct current (dC). A substantial voltage drop will cause a loss of power and the motor will overheat. if the product does not operate when plugged into an outlet, double-check the power supply.

! NOTe: Servicing of a product with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the product to your nearest authorized service center for repair. Always use original factory replacement parts when servicing.

! WARNING: The double insulated system is intended to protect the user from shock resulting from a break in the tool’s internal insulation. Observe all normal safety precautions to avoid electrical shock.


12e

lect

rica

l

eXTeNSION CORDS

When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the product will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. only round jacketed cords listed by Underwriter’s laboratories (Ul) should be used.

When working outdoors with a product, use an extension cord that is designed for outside use. this type of cord is designated with “W-A” or “W” on the cord’s jacket. Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation.

A proper extension cord is available at an authorized service centre.

it is possible to tie the extension cord and power cord in a knot to prevent them from becoming disconnected during use. Make the knot as shown in fig. 1, then connect the plug end of the power cord into the receptacle end of the extension cord. this method can also be used to tie two extension cords together.

! WARNING: Check extension cords before each use. If damaged replace immediately. Never use the product with a damaged cord since touching the damaged area could cause electric shock resulting in serious injury.

! WARNING: Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools, or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury.

–– –– ––


13

Ass

embl

y

UNPACKING

• this product requires no assembly.• Carefully remove the product and any accessories from the box. Make sure that all items

listed in the packing list are included.• inspect the product carefully to make sure no breakage or damage occurred during

shipping.• do not discard the packing material until you have carefully inspected and satisfactorily

operated the product.• if any parts are damaged or missing, please call 1.866.523.5218 for assistance.

PACKING LIST

• electric hedge trimmer• instruction manual

! WARNING: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.

! WARNING: Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

! WARNING: If any parts are damaged or missing, do not operate this product until the parts are replaced. Failure to heed this warning could result in serious personal injury.


14

A

B

Ope

ratio

n

CONNeCTING TO POWeR SUPPLY

this product is designed with a cord retainer that prevents the extension cord from being pulled loose while using.• form a loop with the end of the extension cord.• insert loop portion of extension cord through opening in the bottom of the rear handle and

place over cord retainer.• Slowly pull loop against cord retainer until the slack is removed.• Plug product into extension cord.

! WARNING: Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.

! NOTe: Failure to remove all excess cord slack from extension cord retainer could result in plug loosening from receptacle.

1

2

34

A - Cord retainer

B - Extension cord


15

Ope

ratio

n

STARTING THe HeDGe TRIMMeR

1. Attach an extension cord to your hedge trimmer.2. Place one hand on the trigger handle (1). Place the other hand on the auxiliary handle (2).3. Slide the lock switch (4) toward you then squeeze the trigger switch (3) to turn oN the

hedge trimmer. the trimmer will stay on as long as the trigger switch is squeezed. lock-off switch may be released once hedge trimmer is running.

STOPPING THe HeDGe TRIMMeR

1. Release the trigger switch (3).2. Allow at least 5 seconds for the cutting blade to stop moving.

! WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

! WARNING: Always wear safety goggles or safety glasses with side shields that comply with ANSI Z87.1 when operating power tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.


16O

pera

tion

CUTTING TIPS

• When operating the hedge trimmer, keep the extension cord behind the trimmer. Never drape it over the hedge being trimmed.

• do not force the hedge trimmer through heavy shrubbery. this can cause the blades to bind and slow down. if the blades slow down, reduce the pace.

• do not attempt to cut stems or twigs that are thicker than 2/3” (17 mm), or those obviously too large to feed into the cutting blade. Use a non-powered hand saw or pruning saw to trim large stems.

• if blades do become jammed, stop the motor, allow the blades to stop, and disconnect the plug from the power source before attempting to remove the obstruction.

• if desired, you can use a string to help cut your hedge level. decide how high you want the hedge. Stretch a piece of string along the hedge at the desired height. trim the hedge just above the guide line of string. trim the side of a hedge so that it will be slightly narrower at the top. More of the hedge will be exposed when shaped this way, and it will be more uniform.

• Wear gloves when trimming thorny or prickly growth. When trimming new growth, use a wide sweeping action, so that the stems are fed directly into the cutting blade. older growth will have thicker stems and will be trimmed easiest by using a sawing movement. the unit is used for cutting in either direction in a slow, sweeping action from side to side.

• Stand so that you are stable and balanced on both feet. do not overreach.• inspect and clear the area of any hidden objects.• Never use the hedge trimmer near power lines, fencing, posts, buildings, or other

immovable objects.• Never use a blade after hitting a hard object without first inspecting it for damage. do not

use if any damage is detected.• Never touch blades or service unit with the power supply connected.

! WARNING: Clear the area to be cut before each use. Remove all objects such as cords, lights, wire, or loose string which can become entangled in the cutting blade and create a risk of serious personal injury.

! WARNING: Always keep both hands on the hedge trimmer handles. Never hold shrubs with one hand and operate hedge trimmer with the other. Failure to heed this warning can result in serious injury.

! WARNING: Read the safety information for safe operation using the blade. extreme care must be taken when using blades to ensure safe operation. Refer to General Safety Rules and Specific Safety Rules.


17

Mai

nten

ance

GeNeRAL MAINTeNANCe

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

! WARNING: Blades are sharp, when handling the blade assembly, wear non-slip, heavy-duty protective gloves. Do not place your hand or fingers between blades or in any position where they could get pinched or cut. Never touch blades or service unit with the power supply connected.

! WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic which may result in serious personal injury. Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at an authorized service center.

! WARNING: Before inspecting, cleaning, or servicing the machine, disconnect the plug from power source and wait for all moving parts to stop. Failure to follow these instructions can result in serious personal injury or property damage.

! WARNING: Always wear safety goggles or safety glasses with side shields that comply with ANSI Z87.1 during product operation. If operation is dusty, also wear a dust mask.

! WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.


18

CLeANING THe HeDGe TRIMMeR

• Stop the motor and disconnect from power supply.• Clean dirt and debris from the body of the hedge trimmer, using a damp cloth with a mild

detergent.

STORING THe TRIMMeR

• Clean all foreign material from the product.• Store it in a well-ventilated place that is inaccessible to children.• Keep away from corrosive agents such as garden chemicals and de-icing salts.

! NOTe: Do not use any strong detergents on the plastic housing or the handle. They can be damaged by certain aromatic oils such as pine and lemon, and by solvents such as kerosene.

Mai

nten

ance


19

War

rant

y

Yardworks CANADA will not be liable for incidental or consequential loss or damage.

2-YeAR LIMITeD WARRANTY

for tWo YeARS from the date of purchase within Canada, Yardworks CANAdA will, at its option, repair or replace for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.

THIS WARRANTY DOeS NOT COVeR:

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or

2. the unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or

3. Normal wear, except as noted below;4. Routine maintenance items such as

lubricants, blade sharpening;5. Normal deterioration of the exterior finish

due to use or exposure.

FULL 120-DAY WARRANTY ON NORMAL WeAR PARTS:

Normal wear parts are defined as blade adaptors, blades, grass bags and tires. these parts are warranted to the original purchaser to be free from defects in material and workmanship for a period of one hundred twenty (120) days from the date of retail purchase.

HOW TO OBTAIN SeRVICe:

Warranty service is available by calling the toll-free helpline, at 1.866.523.5218. the factory will not accept the return of a complete unit unless prior written permission has been extended by Yardworks CANAdA.

TRANSPORTATION CHARGeS:

transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. the purchaser must pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by Yardworks CANAdA.

OTHeR WARRANTIeS:

All other warranties, express or implied, including any implied warranty of merchantability is limited in its duration to that set forth in this express limited warranty. the provisions as set forth in this warranty provide the sole and exclusive remedy of Yardworks CANAdA obligations arising from the sale of its products.

Made in Chinaimported byYardworks Canada toronto, Canada M4S 2B8

Hedge Trimmer - canadiantire.ca€¦ · operate with two Hands Hold and operate the hedge trimmer...

Documents

Transcript of Hedge Trimmer - canadiantire.ca€¦ · operate with two Hands Hold and operate the hedge trimmer...