Heavy Equipment Inspection Checklist
-
Upload
juned-hamid-khan -
Category
Documents
-
view
303 -
download
40
description
Transcript of Heavy Equipment Inspection Checklist
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
ARTICULATED DUMP TRUCK
Statement of Operator Competence - Required
Form: HSE-INSP-0001
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Plate No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival on site. Check Box to be ticked after visual inspection by HSE Department
Verify Check CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
Verify Check
Handrails Steps
Verify Check
(Signs on both sides of vehicle)
KEEP CLEAR
Verify Check
Exhaust
WARNING DEVICES Verify Check Horn Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Note : Register if to be used on Public Roads
Verify Check
Tyres Wheels Brakes Park Brake Verify Check
Rams Hoses
Connections (check for excessive wear,
and leaks)
Hydraulics
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation.
Mobile Plant Prestart Checklist
BACKHOE
Statement of Operator Competence Required
Form: HSE-INSP-0002
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Plate No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check CAB Cleanliness Seat Operator Restraint Instruments & Labelling Levers / Controls Pedals ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors
Verify Check
(Signs on both sides of vehicle)
KEEP CLEAR
Verify Check
Stabilisers
Verify Check
Tyres Wheels Brakes
Park Brake
Verify Check
Handrails Steps
Verify Check
Rams Hoses
Connections (check for excessive wear,
and leaks)
Hydraulics
Verify Check
SWL
WARNING DEVICES Verify Check Horn Amber Flashing Beacon Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check
DANGER BEWARE OVERHEAD WIRES & UNDERGROUND SERVICES
Verify Check
Pivots Connecting Rods Safety Pins (no excessive wear)
Verify Check
SWL Crane Chart
Verify Check
Engine Guarding
Verify Check
Exhaust
Hydraulics Verify Check Rams Hoses Connections (check for excessive wear and leaks)
Verify Check
Travelling Hitch
Verify Check
Connecting Rods & Safety Pins
SWL
Verify Check
Quick Hitch Safety Pins (where applicable)
-
This is to certify that the plant being supplied conforms to the relevant HS&E Legislation, and the requirements as detailed above. HSE Department will check this Pre-start Checklist to ensure the supplier has verified compliance to Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
COMPACTOR
Statement of Operator Competence - Required
Form: HSE-INSP-0003
Issue No.:
Date:
Supplier Verification & Plant Details Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Office Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check
Handrails Steps
Verify Check WARNING DEVICES Horn Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS Verify Check
DANGER SAFE WORKING LIMITS
ON BATTERS Ratio 2 to 1 Eg only As per Manufacturers Specifications
Verify
CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
Verify Check
Exhaust
Verify Check
Engine Guarding
Hydraulics Verify Check Rams Hoses Connections (check for excessive wear, and leaks)
Verify Check Crush Point Hazard Sign displayed both sides
Verify Check
Brakes Park Brake
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will check this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
BULL DOZER
Statement of Operator Competence Required
Form: HSE-INSP-0004
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
Verify Check
Pivots Pins Connections Safety Pins
Verify Check
Tracks Complete Idlers Adjusted
Drivers Free from Leaks
Tracks
Verify Check
Handrails Steps
WARNING DEVICES Verify Check Horn Amber Flashing Beacon Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check
DANGER BEWARE OVERHEAD WIRES & UNDERGROUND SERVICES
Verify Check
Rams Hoses Connections (check for excessive wear, leaks and creep)
Verify Check
Exhaust
Verify Check
Engine Guarding
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE will assess this Pre-start Checklist to ensure the supplier has verified compliance to Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSEManagement will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
DRUM ROLLER
Statement of Operator Competence - Required
Form: HSE-INSP-0005
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
CAB Verify Cleanliness
Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
Verify Check
Hoses Connections (check for excessive wear and leaks)
Hydraulics
Verify Check Crush Point Hazard Sign displayed both sides
Verify Check
Handrails Steps
WARNING DEVICES Verify Check Horn Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check DANGER SAFE WORKING LIMITS ON BATTERS
Ratio 4 to 1 Eg only As per Manufacturers Specifications
Verify Check
Locating lock for Low/Neutral/Lower Range Pad lock provided Warning sign Hasp must be locked in position before operating
Verify Check
Exhaust
Verify Check
Tyres Wheels Brakes
Park Brake
Verify Check
Engine Guarding
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
ELEVATING WORK PLATFORM Knuckle Boom
Statement of Operator Competence - Required
Form: HSE-INSP-0006
Issue No.:
Date:
Supplier Verification & Plant Details
Sub-con name
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
WARNING DEVICES Verify Check Horn Amber Flashing Beacon Motion Alarms Raise & Lower Alarms Out of Level Alarm
Verify Check BASKET Cleanliness Operator Restraint Instruments & Labelling Levers / Controls Pedals Log Book Deadman Switch Operation Instruction (available on plant)
Verify Check
Tyres Wheels Brakes
Park Brake
Verify Check WARNING SIGNS
Harness Available
Verify Check DANGER BEWARE OVERHEAD WIRES
&SERVICES
Hydraulics Verify Check Rams Hoses Connections (check for excessive Wear and leaks)
Verify Check
Pivots Connecting Rods Safety Pins (no excessive wear)
Verify Check
SWL / Crane Chart
Verify Check
Safety Harness & Lanyard
Verify Check
Exhaust (if applicable)
Verify Check
Levers / Controls
Verify Check
Rams Hoses
Connections (check for excessive wear,
leaks and creep)
Hydraulics
Verify Check
Engine Guarding
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
ELEVATING WORK PLATFORM Scissor Lift
Statement of Operator Competence Required
Form: HSE-INSP-0007
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
WARNING DEVICES Verify Check Horn Amber Flashing Beacon (when onsite) Reversing Alarm Head, Tail & Turn Indicators
Verify Check BASKET Cleanliness Instruments & Labelling Levers / Controls Basket & Base Pedals Log Book Operation Instruction (available on plant)
Verify Check
Pivots Connecting Rods Safety Pins (no excessive wear)
Verify Check
Engine Guarding
Verify Check
Tyres Wheels Brakes
Park Brake
Verify Check
Levers / Controls
Verify Check WARNING & RESTRICTION SIGNS
Verify Check
Safety Working Load
Verify Check
Self Closing Gate
Hydraulics Verify Check Rams Hoses Connections (check for excessive Wear and leaks)
Verify Check
Exhaust (if applicable)
Verify Check
Safety Prop Under Scissor
Verify Check
Guarding Of Scissor
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE will assess this Pre-start Checklist to ensure the supplier has verified compliance to Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant RoK OH&S Legislation
Mobile Plant Prestart Checklist
EXCAVATOR
Statement of Operator Competence - Required
Form: HSE-INSP-0008
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Hydraulics Verify Check Rams Hoses Connections (check for excessive wear, leaks and creep)
Verify Check
Handrails Steps
Verify Check
Tracks Complete Idlers Adjusted
Drivers Free from Leaks
Tracks
WARNING DEVICES Verify Check Horn Amber Flashing Beacon Motion Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check DANGER BEWARE OVERHEAD WIRES
& UNDERGROUND SERVICES Hydraulics Verify Check Rams Hoses Connections (check for excessive wear and leaks)
Verify Check
SWL / Crane Chart
Verify Check
Pivots Connecting Rods Safety Pins (no excessive wear)
CAB Verify Check Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
Verify Check
Exhaust Verify Check
Engine Guarding
Verify Check
Quick Hitch Safety Pins (where applicable) (If Quick Hitch is fitted NO LIFTING POINTS Allowed on back of bucket
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
GRADER
Statement of Operator Competence - Required
Form: HSE-INSP-0009
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Plate No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and RoK Plant
Regs. Plant Operator is to provide daily checksheets HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
WARNING DEVICES Verify Check Horn Amber Flashing Beacon Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check SAFE WORK LIMIT ON BATTERS Ratio 2 to 1 Ratio 2 to 1 e.g. only As per Manufacturers Specifications
Verify Check
Pivots Pins Connections Safety Pins
Verify Check
Handrails Steps
Verify Check
Tyres Wheels Brakes
Park Brake
Verify Check
Engine Guarding
Note : Register if to be used on Public Roads
Hydraulics Verify Check Rams Hoses Connections (check for excessive wear and leaks)
Verify Check
Exhaust
Verify Check
Unions Rods Connections
Steering
Verify Check
Drive Guards
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will check this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
FRONT END LOADER
Statement of Operator Competence - Required
Form: HSE-INSP-0010
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
Verify Check
SWL if used as Crane Lift point
Verify Check Crush Point Hazard Sign displayed both sides
WARNING DEVICES Verify Check Horn Amber Flashing Beacon Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check DANGER BEWARE OVERHEAD WIRES
Note : Register if to be used on Public Roads
Verify Check
Pivots Connecting Rods Safety Pins (no excessive wear)
Verify Check
Exhaust
Verify Check
Engine Guarding
Hydraulics Verify Check Rams Hoses Connections (check for excessive Wear and leaks)
Verify Check
Handrails Steps
Verify Check
Tyres Wheels Brakes
Park Brake
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will check this Pre-start Checklist to ensure the supplier has verified compliance to Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant Legalisation
Mobile Plant Prestart Checklist
MOBILE CRANE
Statement of Operator Competence - Required
Form: HSE-INSP-0011
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and Vic Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant) Log Book SWL / Crane Chart
Verify Check
Hambone & Wedge
Verify Check
Slings / Ropes / Chains (Tagged and in good working order) Electrical Wiring (No visual signs of damage) Steel or Timber Pads
Verify Check
Handrails Steps Verify Check
Outriggers & Rams Operational
WARNING DEVICES Verify Check Horn Amber Flashing Beacon Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check
DANGER BEWARE OVERHEAD WIRES, PIPES and SERVICES
Verify Check
Pivots Connecting Rods Safety Pins (no excessive wear)
Boom
Verify Check
Engine Guarding
Hydraulics Verify Check Rams Hoses Connections (check for excessive Wear and leaks)
Verify Check
Tyres Wheels Brakes Park Brake
Verify Check
Slew Radius / Barricading for around Outriggers
Verify Check
Exhaust
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
MULTI-WHEEL ROLLER
Statement of Operator Competence - Required
Form: HSE-INSP-0012
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and Vic Plant
Regs. Plant Operator is to provide daily checksheets to HSE Where
applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
WARNING DEVICES Verify Check Horn Amber Flashing Beacon Motion Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check
Handrails Steps
Verify Check
Exhaust
Verify Check
Engine Guarding
Verify Check
Tyres Wheels
Park Brake
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
ROLLER Smooth or Pad Foot
Statement of Operator Competence Required
Form: HSE-INSP-0013
Issue No.: 1
Date:
Supplier Verification & Plant Details
Plant Owner:
Address:
City/Suburb:
Phone:
Plant Make:
Plant Model:
Serial No.:
Signature:
Plant to conform to manufacturers specifications and Vic Plant
Regs. Plant Operator is to provide daily checksheets to HSE Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
Verify Check
Exhaust
Verify Check
Engine Guarding
Verify Check
Handrails Steps
Hydraulics Verify Rams
Hoses Connections (check for excessive
wear and leaks)
Verify Check WARNING DEVICES Horn Amber Flashing Beacon Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS Verify Check
DANGER SAFE WORKING LIMITS ON BATTERS
Ratio 4/1 Eg only As per Manufacturers Specifications
Verify Check
Locating lock for Low/Neutral/Lower Range
Pad lock provided
Warning sign Hasp must be locked in position before
operating
Verify Check Crush Point Hazard Sign displayed both sides
Verify Check
Rubber Mounts (Drum)
Verify Check
Drum Cleaning Rakes
Verify Check
Tyres Wheels Brakes Park Brake
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
SCRAPER Twin Engine
Statement of Operator Competence Required
Form: HSE-INSP-0014
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify
CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
WARNING DEVICES Verify Check Horn Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check
Handrails Steps
Hydraulics Verify Check Rams Hoses Connections (check for excessive Wear and leaks)
Verify Tyres
Wheels Brakes Park Brake
Note : Register if to be used on Public Roads
Verify Check
Exhaust Verify Check
Exhaust
Verify Check
Pivots Connecting Rods
Safety Pins (no excessive wear)
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will check this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. Company Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
SCRAPER
Statement of Operator Competence Required
Form: HSE-INSP-0015
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
Verify Check
Tyres Wheels Brakes
Park Brake
Hydraulics Verify Check
Rams Hoses Connections
WARNING DEVICES Verify Check Horn Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Note : Register if to be used on Public Roads
Verify Check
Exhaust
Verify Check
Pivots Connecting Rods
Safety Pins (no excessive wear)
Hydraulics Verify Check Rams Hoses
Connections (check for excessive
Wear and leaks)
Verify Check
Handrails Steps
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. Company Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
SKID STEER LOADER
Statement of Operator Competence Required
Form: HSE-INSP-0016
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check
Pivots Connecting Rods Safety Pins (no excessive wear)
Verify Check WARNING DEVICES Horn Amber Flashing Beacon Reversing Alarm
Verify Check CAB Cleanliness Seat Operator Restraint Instruments & Labelling Levers / Controls Pedals Protective Mesh Rear View Mirrors ROPS (Roll Over Protective Structure) Operator Instruction (available on plant)
Verify Check
SWL / Crane Chart
Verify Check
Tyres Wheels Brakes
Park Brake
Verify Check
Exhaust
Verify Check
Engine Guarding
Verify Check Hydraulics Rams Hoses Connections (check for excessive wear and leaks)
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS MUST BE WORN
Verify Check
DANGER BEWARE OVERHEAD WIRES & UNDERGROUND SERVICES
Verify Check
Rams Hoses
Connections (check for excessive wear,
leaks and creep)
Hydraulics
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE will check this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
TRACK LOADER
Statement of Operator Competence Required
Form: HSE-INSP-0017
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE. Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department.
Verify Check
Connecting Rods & Safety Pins
Verify Check
Brakes Park Brake
Verify Check CAB Cleanliness Seat Condition OK Operator Restraint Provided Instruments Operational & Labelled Levers / Controls Operational Pedals in Good Condition ROPS (Roll Over Protective Structure) Windows / Wipers / Washers Rear View Mirrors Operator Instruction (available on plant)
Verify Check
SWL if used as Crane Lift Point
Hydraulics Verify Check Rams Hoses Connections (check for excessive Wear and leaks)
Verify Check
Tracks Complete Idlers Adjusted Drivers Free from Leaks
Tracks Verify Check
Tracks Complete Idlers Adjusted
Drivers Free from Leaks
Tracks Verify Check Handrails
Steps
Verify Check
Engine Guarding
Verify Check
Exhaust
Verify Check
Pivots Connecting Rods Safety Pins (no excessive wear)
WARNING DEVICES Verify Check Horn Amber Flashing Beacon Reversing Alarm
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
Verify Check DANGER BEWARE OVERHEAD WIRES
& UNDERGROUND SERVICES
-
This is to certify that the plant being supplied conforms to the relevant HSE Legislation, and the requirements as detailed above. HSE Department will assess this Pre-start Checklist to ensure the supplier has verified compliance to HSE Legislative requirements and, to register the plant onto the site. The operator will be required to participate in ongoing training and perform work in accordance with the relevant Work Method Statement. Should the plant be found to not conform to the above, then it will be prevented from commencing work on the site until the non-compliance is rectified. HSE Management will not reimburse the Owner / Supplier / Contractor for any down / lost time so caused from the non-conformance.
This form does not remove any liability for the plant supplier to conform with the relevant HSE Legislation
Mobile Plant Prestart Checklist
TRUCK and TRAILER Articulated Vehicle
Statement of Operator Competence Required
Form: HSE-INSP-0018
Issue No.:
Date:
Supplier Verification & Plant Details
Plant Supplier
Phone Number
Plant Make
Plant Model
Serial No.
Name
Signature:
Date
Plant to conform to manufacturers specifications and HSE Plant
Regs. Plant Operator is to provide daily checksheets to HSE . Where applicable, Personal Protective Equipment must be worn. Plant Log Book Detailing service history in accordance with
Manufacturers specifications should be written legibly in English.
Contractor must produce proof of competence of operator, e.g., Certificate of Competence, Licence, Detailed Log Book
HSE Use Only
NOTE: Sign only when all items have been checked
Plant Check By: Position: Date: / /
Instructions: Verify Box to be ticked by Owner / Supplier / Operator prior to arrival onsite. Check Box to be ticked after visual inspection by HSE Department
Verify Check CABIN Cleanliness Seat Seat Belts Instruments & Labelling Levers / Controls Pedals Windows / Wipers / Washers Rear View Mirror Current Registration Sticker
Air / Hydraulics Verify Check Rams Hoses Connections (check for excessive wear and leaks) Hoist Control from Cabin Tail Gate Control from Cabin
Verify Check
KEEP CLEAR AIR OPERATED TAILGATE
Verify Check
Exhaust
Verify Check
Tyres Wheels Brakes
Park Brake
Verify Check
Handrails Steps
Verify Check
Connecting Rods Safety Pins
(no excessive wear visible
Towing Hitch
Verify Check WARNING SIGNS (In Cabin)
SEAT BELTS
WARNING DEVICES Verify Check Horn Amber Flashing Beacon (when onsite) Reversing Alarm Head, Tail & Turn Indicators
Steering Tyres Verify Check No Cuts or Splits Good Tread Condition Not Recaps
01 SECL.INSP 0001 Articulated DTruck CheckMobile PlantARTICULATED DUMP TRUCKStatement of Operator Competence - RequiredSupplier Verification & Plant Details
SEAT BELTSHydraulicsCABWARNING SIGNS (In Cabin)WARNING DEVICESHSE Use Only
02 SECL.INSP 0002 BackHoe CheckMobile PlantBACKHOEStatement of Operator Competence RequiredSupplier Verification & Plant Details
HydraulicsCABHydraulicsSWLDANGER BEWARE OVERHEAD WIRESSEAT BELTS
WARNING SIGNS (In Cabin)WARNING DEVICESHSE Use Only
03 SECL.INSP 0003 Compactor CheckMobile PlantCOMPACTORStatement of Operator Competence - RequiredSupplier Verification & Plant Details
CABHydraulicsRatio 2 to 1SEAT BELTS
WARNING SIGNS (In Cabin)WARNING DEVICESHSE Office Use Only
04 SECL.INSP 0004 BullDozer CheckMobile PlantBULL DOZERStatement of Operator Competence RequiredSupplier Verification & Plant Details
CABTracksDANGER BEWARE OVERHEAD WIRESSEAT BELTS
WARNING SIGNS (In Cabin)WARNING DEVICESHSE Use Only
05 SECL.INSP 0005 DrumRoller CheckMobile PlantDRUM ROLLERStatement of Operator Competence - RequiredSupplier Verification & Plant Details
Ratio 4 to 1CABHydraulicsSEAT BELTS
WARNING SIGNS (In Cabin)WARNING DEVICESHSE Use Only
06 SECL.INSP 0006 Elevating Platform CheckMobile PlantELEVATING WORK PLATFORMStatement of Operator Competence - RequiredSupplier Verification & Plant Details
DANGER BEWARE OVERHEAD WIRESBASKETHydraulicsHarness Available
WARNING SIGNSWARNING DEVICESHydraulicsHSE Use Only
07 SECL.INSP 0007 Scissor Lift CheckMobile PlantELEVATING WORK PLATFORMStatement of Operator Competence RequiredSupplier Verification & Plant Details
HydraulicsBASKETWARNING DEVICESHSE Use Only
08 SECL.INSP 0008 Tracked Excavator CheckMobile PlantEXCAVATORStatement of Operator Competence - RequiredSupplier Verification & Plant Details
DANGER BEWARE OVERHEAD WIRESTracksSEAT BELTS
CABWARNING SIGNS (In Cabin)HydraulicsHydraulicsWARNING DEVICESHSE Use Only
09 SECL.INSP 0009 Grader CheckMobile PlantGRADERStatement of Operator Competence - RequiredSupplier Verification & Plant Details
SteeringSAFE WORK LIMIT ON BATTERSRatio 2 to 1 Ratio 2 to 1
CABHydraulicsSEAT BELTS
WARNING SIGNS (In Cabin)WARNING DEVICESHSE Use Only
10 SECL.INSP 0010 Front End Loader CheckMobile Plant FRONT END LOADERSupplier Verification & Plant Details
HydraulicsCABDANGER BEWARE OVERHEAD WIRESSEAT BELTS
WARNING SIGNS (In Cabin)WARNING DEVICESHSE Use Only
11 SECL.INSP 0011 Mobile Crane CheckedMobile PlantMOBILE CRANEStatement of Operator Competence - RequiredSupplier Verification & Plant Details
HydraulicsBoomCABDANGER BEWARE OVERHEAD WIRES,SEAT BELTS
WARNING SIGNS (In Cabin)WARNING DEVICESHSE Use Only
12 SECL.INSP 0012 MultiWheel Roller Check()Mobile PlantMULTI-WHEEL ROLLERStatement of Operator Competence - RequiredSupplier Verification & Plant Details
SEAT BELTSWARNING SIGNS (In Cabin)WARNING DEVICESCABHSE Use Only
13 SECL.INSP 0013 Pad Foot Roller Check()Mobile PlantROLLER Smooth or Pad FootStatement of Operator Competence RequiredSupplier Verification & Plant Details
HydraulicsRatio 4/1SEAT BELTS
WARNING SIGNS (In Cabin)CABWARNING DEVICESHSE Use Only
14 SECL.INSP 0014 Scraper Check()Mobile PlantSCRAPER Twin EngineStatement of Operator Competence RequiredSupplier Verification & Plant Details
SEAT BELTSWARNING SIGNS (In Cabin)HydraulicsWARNING DEVICESCABHSE Use Only
15 SECL.INSP 0015 One Engine Scraper Check()Mobile PlantSCRAPERStatement of Operator Competence RequiredSupplier Verification & Plant Details
SEAT BELTSHydraulicsWARNING SIGNS (In Cabin)CABWARNING DEVICESHydraulicsHSE Use Only
16 SECL.INSP 0016 Skid Steer Loader()Mobile PlantSKID STEER LOADERStatement of Operator Competence RequiredSupplier Verification & Plant Details
CABHydraulicsHydraulicsWARNING DEVICESDANGER BEWARE OVERHEAD WIRESSEAT BELTS MUST BE WORN
WARNING SIGNS (In Cabin)HSE Use Only
17 SECL.INSP 0017 Tracked Loader Check()Mobile PlantTRACK LOADERStatement of Operator Competence RequiredSupplier Verification & Plant Details
TracksHydraulicsTracksCABDANGER BEWARE OVERHEAD WIRESSEAT BELTS
WARNING SIGNS (In Cabin)WARNING DEVICESHSE Use Only
18 SECL.INSP 0018 TruckTrailer ()Mobile PlantTRUCK and TRAILER Articulated VehicleSupplier Verification & Plant Details
Towing HitchKEEP CLEARSEAT BELTS
WARNING SIGNS (In Cabin)Steering TyresWARNING DEVICESCABINAir / HydraulicsHSE Use Only