Heavy-duty_anchor_TA_M-T01122015_100149

http://www.fischer.de/en/ - 12/01/2015

Heavy-duty anchor TA M-T

Hig

h p

erf

orm

ance

ste

el a

nch

ors

1

The installation-friendly push-through anchor for fixings in non-

cracked concrete

VERSIONS

zinc-plated steel▪

BUILDING MATERIALS

Approved for:Concrete C20/25 to C50/60, non-cracked

▪

Also suitable for:Concrete C12/15▪Natural stone with dense structure▪

APPROVALS

ADVANTAGES

The optimised geometry minimisessetting energy and allows for use inextremely narrow spaces. Thisallows for user-friendly installation.

▪

The three-part expansion sleevecreates even load distribution, thusallowing small edge and axialspacing. Thus the TA M-T isextremely flexible.

▪

The TA M-BP version with twist-offhead hinders the dismantling of thefixture for use as a theft-deterrentand break-in protection.

▪

The detachable screw connectionallows for surface flush removal.

▪

APPLICATIONS

Steel constructions▪Handrails▪Consoles▪Ladders▪Cable trays▪Machines▪Staircases▪Gates▪Façades▪

FUNCTIONING

The TA M-T is suitable for push-through installation.

▪

When applying the torque, the coneis pulled into the expansion sleeveand expands it against the drill holewall.

▪

The hexagonal head of the TA M-BPis tightened until it breaks off.

▪



Hig

h p

erf

orm

ance

ste

el a

nch

ors

2

TECHNICAL DATA


ETA-

appr

oval Drill hole diameter Anchor length Min. drill hole depth

for through fixingsMax. fixture

thicknessdo l h2 t fix

Article name Art.-No. [mm] [mm] [mm] [mm]TA M8 T/25 S 090268 ■ 12 84 95 25TA M10 T/25 S 090269 ■ 15 100 110 25TA M12 T/25 S 090270 ■ 18 114 120 25

211

3

TECHNICAL DATA

Heavy-duty▪anchor▪TA M-T,▪for▪push-through▪installation

zinc-plated steel

Appr

oval

Drill hole diameter

Anchor length Max. fixture thickness

Thread Width across nut Washer (outer diameter x thick-

ness)

Sales unit

do l t fix M SW

Art.-No. ETA [mm] [mm] [mm] [mm] [mm] [pcs]Item gvz

TA M6 T/25 S 090267 ■ 10 80 25 M 6 10 18 x 1,6 50TA M8 T/25 S 090268 ■ 12 84 25 M 8 13 24 x 2 50TA M10 T/25 S 090269 ■ 15 100 25 M 10 17 30 x 2,5 25TA M12 T/25 S 090270 ■ 18 114 25 M 12 19 37 x 3 20

TECHNICAL DATA

Heavy-duty▪anchor▪TA M-T BP,▪with▪twist-off▪head

zinc-plated steel

Drill hole diameter

Anchor length Max. fixture thickness

Thread Width across nut Washer (outer diameter x thick-

ness)

Sales unit

do l t fix M SW

Art.-No. [mm] [mm] [mm] [mm] [mm] [pcs]Item gvz

TA M8 BP 090265 12 84 25 M 8 13 24 x 2 50

Non-cracked concreteType Effective

anchorage depthMin.

member thicknessInstallation

torquePermissibletensile load

Permissibleshear load

Min.spacing

Min.edge distance

hef hmin Tinst Nperm3) Vperm

3) smin2) cmin

2)

[mm] [mm] [Nm] [kN] [kN] [mm] [mm]

TA M6 T 40 100 10,0 3,6 3,3 80 50TA M8 T 45 100 20,0 5,7 6,7 90 60TA M10 T 55 110 40,0 9,5 11,0 110 70TA M12 T 70 140 75,0 11,9 17,0 160 120

Heavy-duty anchor TA M-THighest permissible loads for a single anchor1)▪in▪concrete▪C20/254)

For▪the▪design▪the▪complete▪approval▪ETA▪-▪04/0003▪has▪to▪be▪considered.

1) The partial safety factors for material resistance as regulated in the approval as well as a partial safety factor for load actions of γL = 1,4 are considered. As an single anchor counts e.g. an an-chor with a spacing s ≥ 3 x hef and an edge distance c ≥ 1,5 x hef. Accurate data see approval.

2) Minimum possible axial spacings resp. edge distance while reducing the permissible load.3) For combinations of tensile loads, shear loads, bending moments as well as reduced edge

distances or spacings (anchor groups) see approval.4) For higher concrete strength classes up to C50/60 higher permissible loads may be possible.

LOADS

Hig

h p

erf

orm

ance

ste

el a

nch

ors




Hig

h p

erf

orm

ance

ste

el a

nch

ors

3

Heavy-duty_anchor_TA_M-T01122015_100149

Documents

Transcript of Heavy-duty_anchor_TA_M-T01122015_100149