Heavy Duty Hydraulic Roundline Cylinders - FPS Fluid … Cylinder RDH Heavy Duty... · fluid & gas...

aerospaceclimate control electromechanicalfiltrationfluid & gas handlinghydraulicspneumaticsprocess controlsealing & shielding

Heavy Duty Hydraulic Roundline CylindersSeries RDH


Parker Hannifin CorporationIndustrial Cylinder DivisionDes Plaines, Illinois USAwww.parker.com/cylinder

Catalog HY08-1320-2/NA

In line with our policy of continuing product improvement, specifications and information contained in this catalog are subject to change.

Copyright ©2011 by Parker Hannifin Corporation. All rights reserved.

PRINTED IN THE U.S.A.

WARNINGFAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from the Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having expertise. It is important that you analyze all aspects of your application, including consequences of any failure and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met.The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.

Offer of SaleThe items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by provisions stated on a separate page of the document entitled ‘Offer of Sale’.

Series CHE• 20through100mmBoreSizes•StrokeLengthsto150mm•OperatingPressureto140bar•4DifferentRodEndsAvailable

Accessories• CorrosionResistant• Cast&Fabricated• TraditionalAccessories• MetricAccessories• StainlessSteelAccessories

Series CHD• 20through80mmBoreSizes• StrokeLengthsto100mm• OperatingPressureto207bar• 4DifferentRodEndsAvailable




I

With annual sales exceeding $12 billion, Parker Hannifin is the world's leading diversi-fied manufacturer of motion and control technologies and systems, providing precision-engineered solutions for a wide variety of mobile, industrial and aerospace markets. The company employs approxi-mately58,000peoplein47countries around the world. Parker has increased its annual dividends paid to shareholders for55consecutiveyears,among the top five longest-running dividend-increase recordsintheS&P500index.Formoreinformation,visit the company’s web site at http://www.parker.com, or its investor information site at http://www.phstock.com.

Parker Hannifin is the world’s largest manufacturer of Hydraulic, Pneumatic, Electro-Hydraulic and Electric cylinders.With our global presence in 47countries,weareperfectlysuited to provide superior customer service to any location.

Here is a short list of what you can expect from Parker:• DesignandApplication

Experience• Responsiveness• FastProductDelivery• SystemIntegration

Capabilities• IngenuityandCreativity• OrganizationalIntegrity• HighestQuality• CompetitivePricing• FinancialStability•WorldwideSupport

Markets and ApplicationsParker cylinders are utilized worldwide in many markets and applications, including:• OilandGas•RenewableEnergy•PowerGeneration•ProcessValves•Mining•PrimaryMetals•MetalFabrication•Marine•CivilEngineering Projects

(including US Army Corps of Engineers Projects)

•Militaryand Commercial Aerospace

•MaterialHandling•TestingandAnalysis•Construction•WoodProcessing•WasteProcessing•Automotive•TirePress•MachineTools•Entertainment


Composite Wear Rings

Parker WearGard™ bearing materials are backed by over 30 years of manufacturing expertise.•Heatstabilizedandinternallylubricatedforlow

friction and maximum service life in any application.•Strengthcharacteristicsmeetorexceedmostmetals

traditionally used in wear rings.

Easy Installation

Standard mounts and rod ends accommodate commercially-available NFPAaccessories.

Switch-Ready

•The Parker ALS Switch is the lowest cost point feedback solution for carbon steel cylinders with a piston magnet ring.•Switches can be located

anywhere along the stroke and in any orientation.•Unique round body brackets

minimize installation time.•EPS & CLS threaded switches are

available for end-of-stroke sensing.

Advanced Sealing Technology

All components are manufactured by Parker and designed for high performance, long service life, low friction and zero leakage. •Tri-lip rod seal (3 sealing edges!) and bi-directional piston seal

feature proven leak-free performance.•Durable polyurethane material is used to maximize seal life.•Nitrile end seals and backup rings on a smooth bore of the

cylinder body for optimal sealing and elimination of extrusion problems.•Composite rod and piston wear rings are internally lubricated

for reduced friction and formulated for heavy-duty, load-bearing applications.•Standard rod material is case-hardened, hard chrome plated

and polished to an optimum finish.•Andsincewemakeourownseals,all seals have immediate

availability in other popular compounds.

Proven Exterior Toughness

•Steel cap, cylinder body and ports for high-strength in rough environments.•Case hardened, hard chrome plated and

polished carbon steel piston rod for damage resistance, long rod seal life and low friction.•Outboard urethane rod wiper seal to

remove external debris and adherents from the piston rod. •High quality paint coating for interior or

exterior applications.

Series RDH Cylinders from Parker

Environmentally FriendlyRoHS-compliant materials

II


New Value from a Standard Platform

Advanced ManufacturingCylinders, by nature, are customized products. Whether it is something basic, such as stroke length, or something more complex, such as a special head, raw material and basic parts must be procured and manufactured into components for configured cylinders.

Organizing cylinder production and assembly requires some degree of planning. To do so, without sacrificing customer service, requires a sharp focus on advanced manufacturing processes.

Lean Manufacturing PrinciplesParkerHannifinhasutilizedLeanManufacturingtechniquesformanyyears, even before it was called by name.CellularManufacturing,ValueStreamMapping,Kaizenevents,Kanban,One-PieceFlowandotherinfluences are pervasive in our manufacturing processes.

WenowfollowLeanImplementationto focus all aspects of our operation on the same goals for customer service.

Series RDH cylinders are manufacturedintheUSA.Locationis a significant part of our customer service model. We believe that customers value a domestic presence, for many reasons. A few include:

• Quick Delivery – standard lead time is a few days, with the capability of shipping some cylinderconfigurationswithin48hours. We deliver to your request.

• Made-To-Order – we are able to quickly manufacture customized products without the need to carry fixed finished goods inventory. This minimizes time-to-customer and cost-to-customer concerns.

• Late-Day Orders – our West Coast presence can create an order time advantage of up to three hours for many US locations, which may be instrumental in keeping you on schedule.

• Risk Management – the absence of international risks from deal-ing with non-domestic cylinder sup pliers will allow you to relax. Our goal is to offer you the best product, on time, with your finan-cial concerns in mind.

• Non-Standard Designs – since 50%ofapplicationsrequire cylinders that are not catalog-standard, we organized our entire culture for flexibility. Our manu-facturing processes are prepared to accommodate non-standard designs with minimal lead-time adjustments.

Made in U.S.A.

III



Catalog HY08-1320-2/NACustomer Service Locations

Customer Service Locations

California 221 Helicopter Circle Corona, CA 92880 Tel.:(951)280-3800 Fax:(951)280-3808 Fax:(800)869-9886

Connecticut 80 Shaker Road Enfield,CT06082 Tel.:(860)749-2215 Fax:(800)323-0105

Georgia 1300SixFlagsRoad LithiaSprings,GA30122 Tel.:(770)819-3400 Fax:(800)437-3498

Indiana GoodlandPlant 715SouthIroquoisStreet Goodland,IN47948 Tel.:(219)297-3182 Fax:(800)328-8120

Michigan 900 Plymouth Road Plymouth,MI48170 Tel.:(734)455-1700 Fax:(734)455-1007

Oregon 29289 Airport Road Eugene,OR97402 Tel.:(541)689-9111 Fax:(541)688-6771 Fax:(800)624-7996

Atlanta, GA

IV

Enfield, CT

Corona, CA

Plymouth, MI Goodland, IN

Eugene, OR




1

Table of Contents

Table of Contents

Description Page Section

A

B

C

D

Section A – Basic Cylinder Information 2-20Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2AvailableMountingStyles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3CustomOptionsandModifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3FeaturesandBenefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5Application Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6MountingStylesandTipsforApplying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7HowToOrder(SeriesRDHCylinderModelCode). . . . . . . . . . . . . . . . . . . . . . 8-9Rod End Styles and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10MountingInformationforSingleRodCylinders . . . . . . . . . . . . . . . . . . . . . . .11-19MountingInformationforDoubleRodCylinders . . . . . . . . . . . . . . . . . . . . . . . . . 20

Section B – Cylinder Accessories and Replacement Parts 21-30CylinderMountingAccessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-27SphericalBearingMountingAccessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26LinearAlignmentCouplers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Style55PistonRodEndAccessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Parts Identification / Torque Tool Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 29PistonandRodSealKits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Section C – Common Modifications 31-57Water Submersible Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-32 HiLoadPiston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33LowFrictionSeals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-35OtherCommonModifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36ALSSwitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-40EPS-AProximitySensor/CLS-ALimitSwitches . . . . . . . . . . . . . . . . . . . . . 41-43CylinderswithLimitSwitches–Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 44-52CounterbalanceValves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-57

Section D – Engineering Data 60-72Theoretical PushandPullForces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60Cylinder Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Seal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-63Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-65StrokeDataandTolerances/FatigueLife . . . . . . . . . . . . . . . . . . . . . . . . . ..66-67MountingGroupsandForceTransfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66Stop Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Piston Rod Selection Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68-69CylinderSafetyGuide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-71Offer of Sale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

2




2

General Specifications•Heavy duty service•Standardconstruction–threadedhead,weldedcap•Borediameters–1.50"through8.00"•Strokes–availableinanypracticalstrokelength•Pistonroddiameters–0.625"through5.500"

(based on bore size)•Rodendstyles–5standard,specialsavailable•Singlerodendordoublerodends

•Mountingstyles–9standardstylesatvarious application ratings•Nominalpressure–3,000psi1(207Bar)•Standardfluidmedia–filteredhydraulicoil2

•Standardtemperature–-10°Fto+165°F3 •RoHScompliant1 If hydraulic pressure exceeds3,000psi(207Bar),send

application data for engineering evaluation and recommendation.2 See Seal Information pages for appropriate seals with different fluid

media.3 See Seal Information pages for lower and higher temperature

service.

In line with our policy of continuing product improvement, specifications in this catalog are subject to change.

Product Specifications

Head Ductile ironCap Carbon steelCylinder body Carbon steelPiston rod Case-hardened, chrome plated high strength carbon steelRod seal PolyurethaneRod wiper seal UrethaneRodbearing WearGard™

High temperatures Rod seal, rod wiper seal, end (to+250°F) seal,backupringandpistonseal Class5 energizerarefluorocarbon. PistonsealisbronzefilledPTFE.

Extreme high Rod seals, rod wiper seal and temperatures piston seal are bronze filled (to+400°F) PTFE.Endsealo-ring,backupClass 8 ring and seal energizers are fluorocarbon.Bearingsare UltraComp™CGT.

Piston Ductile ironPiston seal PolyurethanePiston seal energizer Nitrile Pistonbearing WearGard™ orMolyGard™ Piston fastener Carbon steelPistonjointo-ring FluorocarbonEnd seal o-ring NitrileBackupring Nitrile

Cylinderseal WaterBaseFluidSeals(Class2)options4 EPR Seals (Class 3)(for chemical FluorocarbonSeals(Class5)compatibility)

HWCFSeals(Class6) Mixed-MediaPistonSeals (bronzefilledPTFEandnitrile)

Lowtemperatures Pistonsealenergizer,end (to-50°F) sealandbackupringare Class4 lowtemperaturerated nitrile.

Magneticring SinteredNdFeB

Pistonrod 17-4PHstainlesssteel, material options chrome plated 303and316stainlesssteelare available at lower operating pressures; consult factory.

Material Specifications–Standard Temperatures and Applications

Operating Temperature Options–Material and Part Changes

Other Standard Options–Material and Part Changes

Forthosediscerningcustomerswantingapersonaltouch, we can “private label” cylinders at no charge. The information must be in text format (no logos) and the label must include our serial number and cylinder pressure rating. Just place an “S” for special in the SpecialModificationfieldandprovidetheprivatelabelinformation in the item notes. We take care of the rest!

Private LabelingIf labels with logos are desired, contact the Industrial Cylinder Division for assistance.

YOUR NAME HERE

4 See Seal Information pages for additional specifications.

3 Parker Hannifin CorporationIndustrial Cylinder DivisionDes Plaines, Illinois USAwww.parker.com/cylinder

3



A

•SpecialHeads, Caps, PistonsandMounts•Mount/PortRelocation •Oversize/UndersizePorts •PortThreadStyles•PortBlocks/ValveManifoldandFlowTubing

(at either end)•MultiplePorts•CartridgeValves•AirBleeds•DoubleRodEnd•Oversize/UndersizeRodDiameters•ExtraThickChromePlatedPistonRod•RodMaterials(stainlesssteels,alloysteels,etc.)•RodCoatings(laser-clad,nanoplating,etc.)•NitridedRod•PinnedRodtoPiston•WeldedRodtoPiston•WeldedRodEndAccessory•ExtraWrenchFlats•RodBoot•ParkerCrown™ Wiper (ExtremeDutyNon-MetallicRodWiper)•MetallicRodWiper•SealMaterials(additionalcompounds)

SphericalBearingCapEnd Crosstube Cap End IntermediateFixedTrunnion

RoundHeadFlange RoundCapFlangeStyle J

Style JP with close

tolerance pilot

Style H

Style DD

Style BB

Style SB/SBM Style TT

Double Rod Cylinders

Style KT Shown

Available Mounting StylesCapFixedEye

Style B

CapFixedClevis

•PolyPakSeals•StopTube•StrokeAdjuster•PointFeedback–ALSSwitch (PNP/NPNMid-StrokeSwitch)•PointFeedback–CLS-ASwitch (Magnetically-ActuatedEnd-Of-StrokeLimitSwitch)•PointFeedback–EPS-ASensor

(PNP End-Of-Stroke Proximity Sensor)•ContinuousLinearPositionFeedback LinearDisplacementTransducer(LDT)•FixedCushions•HighPressureService(>3,000PSI)•PneumaticService•WaterSubmersibleDesign•ChromePlatedBore•NickelPlatedAssembly•Application-SpecificPaint(Marine-Grade,Salt-Spray

Rated, Caustic Washdown, etc.)•StainlessSteelConstruction(deratedoperating

pressure)•MetricRodandBoreDiameters•DualEndSeals

Style T

Basic,NoMount

Custom Options and Modifications

Mountingstyles T, DD and J are available as double rod cylinders.

Custom Options and Modifications (consult factory)

4




4

The inside story on why Series RDH is your best choice in heavy duty roundline cylinders

Ductile Iron Head – Concentric with the bore, it acts as the high-strength rod guide and housing for the rod seal, wiper seal and bearing. Torqued to the cylinder body for lasting cylinder integrity.

Primary Seal – PolyurethaneTri-LipRod Seal is a proven leakproof design –completelyself-compensatingandself-relieving to withstand variations and conform to mechanical deflection that may occur.

Secondary Seal – Dual-Service Urethane Wiperseal™–wipescleanany oil film adhering to the rod on the extend stroke and removes external debris and adherents from the rod on the return stroke.

Piston Rod – Induction case-hardened, hard chrome-plated medium carbon steel, polished to an optimum finish. Piston rods are made from 100,000 psi minimum yield material for .625"through4.000"diametersand70,000psiminimumyieldmaterialforlarger diameters. Stainless steel is available as an option.

Features and Benefits

End Seal – Parker o-ring with backup ring located on a smooth bore to combine leak-free service with an anti-extrusion design.

Buttress Threads – The strongest commercial thread style for pressure vessels with axial and impact loading.

Composite Wear Rings – Parker WearGard™ wear rings are internally lubricated for reduced friction and formulated for heavy-duty, load-bearing applications.

Ports – Seal-welded to the cylinder body. SAE straight thread o-ring ports arestandard.Otherportstyles(NPTF,BSPP,BSPT,etc.)arealsoavailable.

Optional Extreme Temperature/ Low Friction Seal Assembly – DualbronzefilledPTFErodsealsandbronzefilledPTFEwipersealareenergized with fluorocarbon o-rings to maintain consistent contact with the piston rod. The result is excellent sealing performance with low friction. Our seal set provides a “dry rod” surface on the extend stroke with rod scraping to clean the rod on the retract stroke. Heatresistanceto400°FwiththeClass8Sealsoption.Foradditional

details,seetheLowFrictionSealspage and Class 8 Seals specifications on the Seal Information page.


5



A

Cylinder Body – Heavy-wall steel tubing, burnished to a micro finish bore.

Features and Benefits

Piston Seal – Polyurethane bi-directional seal for long service life. Energized for leak-free service at any pressure.

Piston Joint Seal – Parker o-ring for positive joint sealing on a smooth rod diameter.

One-Piece Ductile Iron Piston – The wide piston and bearing are truly designed for heavy-duty industrial applications. One-piece design for strength and product integrity.

Composite Wear Rings – Parker WearGard™ wear rings are internally lubricated for reduced friction and formulated for heavy-duty, load-bearing applications.

Optional Pistons

Hi Load/Low Friction Piston – BronzefilledPTFEpistonsealformaximum seal life in extreme duty and side load applications.

Mixed Media Piston – Used for dissimilar fluids or a gas on either side of the piston (i.e. air/oil applications).

Magnetic Piston – Includes magnetic ringsfortheALSSwitchoption.

Steel Cap and Mount – Concentric with the bore and arc-welded for tough applications.

1Onlyfor1.50"to5.00"bores.For6.00"to8.00"bores,pistonsarethreadedandtorquedtothepistonrod,andsetscrewsareusedtolockthe piston to the rod.

Piston Fastener – Carbon steel, prevailing-torque type nut1 for cylinder serviceability (especially for welded rod ends).

6




6

Application ChecklistThe following checklist should be used to select the best possible cylinder for a given application. Additional information can be referenced in the following pages to help assist in this process. In the event that you have additional questions or concerns, or if more information is required, contact your local Parker distributor or our customer service representatives for assistance.

1. Establish the system requirements • Howheavyistheloadtobemoved? • Whatisthenominaloperatingpressureofthesystem? • Howfardoestheloadhavetomove? • Whatisthespeedatwhichtheloadwillmove? • Whatisthefluidtypeandthetemperaturetowhichthecylinderwillbeexposed?

2. Mounting Style .....................................................................................................................................Pages3and7 • Determinethebestmountingstylefortheapplication.

3. Cylinder Bore and Operating Pressure ......................................................................................................Page60 • Reviewthetheoreticalpushandpullforcestodeterminetheapplicableboreandroddiametersizes.

4. Piston Rod ..............................................................................................................................................Pages66-69 • Determinewhatrodsizewillberequiredtoavoidbuckling. • Determineifasingleordoublerodcylinderisrequired. • Determinetherodendstyleandrodendthread. • Willstoptubingberequired? • Isadequatepullforcestillavailableorisalargerborediameternowrequired?

5. Seals ........................................................................................................................................................ Pages62-63 • Selectthepropersealtypeandconfigurationfortheapplication. • Selectthepropersealtoassurefluidandtemperaturecompatibility.

6. Ports ..........................................................................................................................................................Page64-65 • Selectthebestpossibleportsizeforagivenspeedrequirement. • Selectporttype. • Selectportposition.

7. Piston rod and mounting accessories .................................................................................................Pages 21-28 • Determinehowyouwillattachthecylindertotheload.

8. Optional accessories and modifications ............................................................................................Pages31-58

Application Checklist


7



A

Mounting Styles and Tips for Applying ThemPivot Mountings – B, BB, SB/SBM and TTApplication: • Curvedorarclineforce transfer • Canbeusedincompressionor tension loads • Movementinasimplearc –useB,BBorTTmounts • Movementinacompoundarc –useSB/SBMmount

Advantages: • Easeofmounting • Designflexibility • Selfaligning(SB/SBMmount)

Application: • Curvedorarclineforce transfer • Canbeusedincompressionor tension loads

Trunnion Mountings – DDAdvantages: • Easeofmounting • Designflexibility • Improvedcylinderweight support • Reducespistonandrod bearing loads

Mounting Style Tips

Application: • Straightlineforcetransfer • Compressionloads(push) –useHmount • Tensionloads(pull) –useJ/JPmount

Flange Mountings – J/JP and HAdvantages: • Easeofmounting • Rigidbasemountingdueto large flange area • JPMountpilotimproves alignment of cylinder and load

8




8

Series RDH Model Code

How To Order

Shaded boxes identify the required model number fields. 1 AvailablestandardmountingstylesforK-typecylindersareT,

DD and J/JP. When ordering a double rod cylinder, the piston rod number and piston rod thread style must be specified for both rod ends. The model number should be created as viewing the primary rod end on the left-hand side.

ExampleofaK-typecylinder: 4.00KDDRDHBT14A28A10.000 2 Specify XI dimension. See minimum and maximum XI dimen-sionsonDDIntermediateFixedTrunnionMountingPage.

3 Includes low friction seals for the entire cylinder. Available with standardsealsandSealcodes2,X,4,VandH.

4 UsedwithexternallymountedALSSwitches.Includessealandwearringfromstandardpiston.Availablefor1.50"to6.00"borediameters.Switchoperatingtemperaturerangeis-13°Fto+185°F.SwitchpositionmayberestrictedforMountingStyleDD.Consult factory for other options.

5 Used for dissimilar fluids or a gas on either side of the piston (i.e. air/oil applications). Standard mixed media piston accommodates fluids which are compatible with Class 1 Seals. SeeSealInformationpagesformoredetails.Forotherfluids,consult factory.

6 See Seal Information pages for additional information.7 OptionusedforPistoncode7(MagneticPiston). 8 Used for external chemical compatibility applications, not high

temperature.

2.00

BoreDiameter

Specify bore dia. in inches1.502.00 2.503.254.005.006.007.008.00

BB RDH B T

Double Rod EndCylinder

Specify “K”onlyifDouble Rod Cylinder is required.1

Mounting Style

T=Basic,NoMount B=CapFixedEye BB=CapFixedClevis SB=SphericalBearing Cap EndSBM=SphericalBearing CapEnd,Metric (3,000 psi rating) TT = Crosstube Cap End DD = Intermediate FixedTrunnion2

J = Round Head Flange JP = Round Head FlangewithPilot H = Round Cap Flange

Series

RDH

Piston

B =Standard (Standard Seal with Wear Ring) K =BronzeFilledPTFE Seal with Wear Ring F =LowFriction Cylinder (All Seals)3

7 =Magnetic4 (Standard Seal with Wear Ring andMagnet)W =MixedMedia5 (MixedMediaSeal with Wear Ring)

Ports

Seals6

Blank=Standard (Polyurethane, Class 1) 2 =WaterBase Fluid/HWCF Seals (Classes 2 and6) X = EPR Seals (Class 3) 4 =Low Temperature Seals(Class4) V =Fluorocarbon Seals(Class5) H = Extreme High Temperature Seals (Class 8) K =Class1Seals withBronze FilledPTFE Piston Seal7

E =Fluorocarbon Rod Seal and Wiper Only8

M =MetallicRod Wiper, Standard Seals D =MetallicRod Wiper,Fluoro- carbon Seals

T = Standard (SAE)U=NPTFR=BSPP(ISO228)P=Flange(SAEcode61)B=BSPT


9



A

How To Order

Series RDH Model Code

Special Modification

Piston Rod Number9

1 4 A 6.000

Piston Rod End

12345

A = Standard (UNF)M=Metric13

N = No Threads (only used forStyle55 or Style 3 rod ends)

Stroke14

Specify in inches (see MinimumStandard Stroke table below)

Piston Rod Material12

Specify"S"for special modifica tion other than rod end, and then describe the modification in the item notes.

Piston Rod Threads

4=Style4Small Male7=Style7Thread for Spherical Rod Eye10

8 = Style 8 Intermediate Male 9 = Style 9 Small Female10

55=Style55For Flange Coupling 3 = Style 3 Special (specify)11

Blank=Standard Y=17-4PH Stainless Steel12

Shaded boxes identify the required model number fields.9 Refer to the Stop Tubing and Piston Rod Selection Data

pages to assure that the selected rod number will not buckle under load.

10 Style7A(UNFthreads)andStyle9mayrequireaminimumstroke.SeeMinimumStandardStrokeintabletotheleftfordetails.

11 ProvidedesireddimensionsforKK(orCC),AandW.If otherwise special, supply a dimensioned sketch. Accessories welded to the rod end are available.

12 Otherstainlesssteels(i.e.303,316)areavailablewithaderated maximum operating pressure; consult factory.

13 ForStyle7M,seepage15fordetails.ForStyles4M,8Mand9M,seepage36fordetails.

14 If a stop tube is required, specify gross stroke (net stroke +stoptubelength)inthemodelnumberfield,thenplacean“S”forspecialintheSpecialModificationfieldandspecifythestoptubelengthintheitemnotes.Forstrokelength tolerance, see Stroke Data page.

Minimum Standard StrokeBore

ØRod No. MM

Rod Ø

DD Mount

With Style 9 or 7A Rod End and Standard W Dimension

J Mount All Other Mounts

1.501 0.625 3.03 NoMin. NoMin.2 1.000 3.03 NoMin. NoMin.

2.001 1.000 3.12 NoMin. NoMin.2 1.375 3.12 NoMin. 0.25

2.501 1.000 2.98 NoMin. NoMin.2 1.750 2.98 NoMin. 0.443 1.375 2.98 NoMin. NoMin.

3.251 1.375 3.61 NoMin. NoMin.2 2.000 3.61 NoMin. 0.653 1.750 3.61 NoMin. 0.19

4.001 1.750 3.52 NoMin. NoMin.2 2.500 3.52 1.19 1.943 2.000 3.52 NoMin. 0.40

5.00

1 2.000 3.88 NoMin. 0.152 3.500 3.88 1.29 2.043 2.500 3.88 0.43 1.184 3.000 3.88 1.08 1.83

6.00

1 2.500 4.46 0.49 1.242 4.000 4.46 2.26 3.013 3.000 4.46 1.14 1.894 3.500 4.46 1.35 2.10

7.00

1 3.000 5.10 0.95 1.952 5.000 5.10 3.36 4.363 3.500 5.10 1.16 2.164 4.000 5.10 2.07 3.075 4.500 5.10 2.65 3.65

8.00

1 3.500 5.54 0.94 1.942 5.500 5.54 4.06 5.063 4.000 5.54 1.86 2.864 4.500 5.54 2.44 3.445 5.000 5.54 3.15 4.15

10




10

Rod End DimensionsThread Style 8 (NFPA Style IM)

Intermediate Male

Thread Style 4 (NFPA Style SM)

Small Male

“Special” Thread Style 3Special thread, extension, rod eye, blank, welded rod end accessory, etc. are also available.

Toorder,specify“Style3”andgivedesireddimensionsforKK,A,WorWF.Ifotherwisespecial,furnishdimensionedsketch.

Rod End Styles and Dimensions

Rod End Dimensions

Style 552 Flanged Rod End

Thread Style 91 (NFPA Style SF)

Small Female

A W

DWRENCH

FLATS

KK NA

ØMM

Bore Ø

Rod No.

MM Rod

Ø

Thread A AD AE +.001 -.001

AF Ø

AM Ø

D NA W WGStyle

8 CC

Style 4 & 9 KK

1.501 (std) 0.625 1/2-20 7/16-20 0.75 0.63 0.249 0.38 0.57 0.50 0.56 0.56 1.13

2 1.000 7/8-14 3/4-16 1.13 0.94 0.374 0.69 0.95 0.88 0.94 0.69 1.50

2.001 (std) 1.000 7/8-14 3/4-16 1.13 0.94 0.374 0.69 0.95 0.88 0.94 0.69 1.50

2 1.375 11/4-12 1-14 1.63 1.06 0.374 0.88 1.32 1.13 1.31 0.81 1.75

2.501 (std) 1.000 7/8-14 3/4-16 1.13 0.94 0.374 0.69 0.95 0.88 0.94 0.69 1.50

2 1.750 1 1/2-12 11/4-12 2.00 1.31 0.499 1.13 1.70 1.50 1.69 0.94 2.003 1.375 11/4-12 1-14 1.63 1.06 0.374 0.88 1.32 1.13 1.31 0.81 1.75

3.251 (std) 1.375 11/4-12 1-14 1.63 1.06 0.374 0.88 1.32 1.13 1.31 0.81 1.75

2 2.000 13/4-12 1 1/2-12 2.25 1.69 0.624 1.38 1.95 1.69 1.94 1.00 2.633 1.750 1 1/2-12 11/4-12 2.00 1.31 0.499 1.13 1.70 1.50 1.69 0.94 2.00

4.001 (std) 1.750 1 1/2-12 11/4-12 2.00 1.31 0.499 1.13 1.70 1.50 1.69 0.94 2.00

2 2.500 21/4-12 17/8-12 3.00 1.94 0.749 1.75 2.45 2.06 2.38 1.06 3.253 2.000 13/4-12 1 1/2-12 2.25 1.69 0.624 1.38 1.95 1.69 1.94 1.00 2.63

5.00

1 (std) 2.000 13/4-12 1 1/2-12 2.25 1.69 0.624 1.38 1.95 1.69 1.94 1.00 2.632 3.500 31/4-12 2 1/2-12 3.50 2.69 0.999 2.50 3.45 3.00 3.38 1.06 4.383 2.500 21/4-12 17/8-12 3.00 1.94 0.749 1.75 2.45 2.06 2.38 1.06 3.254 3.000 23/4-12 21/4-12 3.50 2.44 0.874 2.25 2.95 2.63 2.88 1.06 3.63

6.00

1 (std) 2.500 21/4-12 17/8-12 3.00 1.94 0.749 1.75 2.45 2.06 2.38 1.06 3.252 4.000 33/4-12 3-12 4.00 2.69 0.999 3.00 3.95 3.38 3.88 1.06 4.503 3.000 23/4-12 21/4-12 3.50 2.44 0.874 2.25 2.95 2.63 2.88 1.06 3.634 3.500 31/4-12 2.1/2-12 3.50 2.69 0.999 2.50 3.45 3.00 3.38 1.06 4.38

7.00

1 (std) 3.000 23/4-12 21/4-12 3.50 2.44 0.874 2.25 2.95 2.63 2.88 1.06 3.632 5.000 43/4-12 3 1/2-12 5.00 3.19 1.499 3.88 4.95 –3 4.88 1.19 5.383 3.500 31/4-12 2 1/2-12 3.50 2.69 0.999 2.50 3.45 3.00 3.38 1.06 4.384 4.000 33/4-12 3-12 4.00 2.69 0.999 3.00 3.95 3.38 3.88 1.06 4.505 4.500 41/4-12 31/4-12 4.50 3.19 1.499 3.50 4.45 –3 4.38 1.19 5.25

8.00

1 (std) 3.500 31/4-12 2 1/2-12 3.50 2.69 0.999 2.50 3.45 3.00 3.38 1.06 4.382 5.500 51/4-12 4-12 5.50 3.94 1.874 4.38 5.45 –3 5.38 1.19 6.253 4.000 33/4-12 3-12 4.00 2.69 0.999 3.00 3.95 3.38 3.88 1.06 4.504 4.500 41/4-12 31/4-12 4.50 3.19 1.499 3.50 4.45 –3 4.38 1.19 5.255 5.000 43/4-12 3 1/2-12 5.00 3.19 1.499 3.88 4.95 –3 4.88 1.19 5.38

W

KK

NA

ØMM

DWRENCH

FLATS

AWG

ØAFAE

AD

ØAM

R.06

ØMM

1 Style9strokerestrictionsmayapply.SeeMinimumStrokeforStyle 9 Rod End in table on How To Order page for details.

2 ForanyspecialStyle55dimensions,specify“Style3”andprovidethedesireddimensionsforAD,AE,AF,AMandWG.Forotherchanges, specify “S” in the model code, and describe the rod end with a dimensioned sketch.

3 Thesepistonrodshavefour0.515"dia.x0.5"deepspannerwrench holes instead of wrench flats on diameter NA.

A W

NAKK

DWRENCH

FLATS

ØMM


11



A

Mounting Information – 1.50" to 8.00" Bore

Basic, No MountStyle T

Table 1 – Dimensional and Mounting Data


EE

HD

ØE

LB + STROKE

P + STROKEY

W

ZJ + STROKE

ØMM

Bore Ø

Rod No. E Ø

EE HD Add Stroke

NPTF1 SAE2 LB P

1.501 (std) 1.88 3/8 6 1.60 3.56 1.19

2 1.88 3/8 6 1.60 3.94 1.192.00 All 2.38 1/2 8 2.04 4.81 1.932.50 All 3.00 1/2 8 2.37 5.25 1.883.25 All 3.88 3/4 12 2.81 6.00 2.064.00 All 4.61 3/4 12 3.20 6.50 2.505.00 All 5.75 3/4 12 3.79 7.12 2.566.00 All 7.00 1 16 4.58 8.37 3.007.00 All 8.00 11/4 20 5.11 9.00 3.258.00 All 9.25 11/4 20 5.76 9.50 3.25

1 NPTFportsareavailable for no additional charge 2 SAE straight thread o-ring ports are standard

Bore Ø

Rod No. MM Rod Ø

W Y Add Stroke

ZJ

1.501 (std) 0.625 0.56 2.12 4.12

2 1.000 0.69 2.62 4.63

2.001 (std) 1.000 0.69 2.51 5.50

2 1.375 0.81 2.63 5.62

2.501 (std) 1.000 0.69 2.69 5.94

2 1.750 0.94 2.94 6.193 1.375 0.81 2.81 6.06

3.251 (std) 1.375 0.81 3.06 6.81

2 2.000 1.00 3.25 7.003 1.750 0.94 3.19 6.94

4.001 (std) 1.750 0.94 3.40 7.44

2 2.500 1.06 3.52 7.563 2.000 1.00 3.46 7.50

5.00

1 (std) 2.000 1.00 3.70 8.122 3.500 1.06 3.76 8.183 2.500 1.06 3.76 8.184 3.000 1.06 3.76 8.18

6.00

1 (std) 2.500 1.06 4.24 9.432 4.000 1.06 4.24 9.433 3.000 1.06 4.24 9.434 3.500 1.06 4.24 9.43

7.00

1 (std) 3.000 1.06 4.25 10.062 5.000 1.19 4.38 10.193 3.500 1.06 4.25 10.064 4.000 1.06 4.25 10.065 4.500 1.19 4.38 10.19

8.00

1 (std) 3.500 1.06 4.44 10.562 5.500 1.19 4.56 10.683 4.000 1.06 4.44 10.564 4.500 1.19 4.56 10.685 5.000 1.19 4.56 10.68

12




12


Cap Fixed Eye MountingStyleB



ZC + STROKE

LB + STROKE

P + STROKEY

W

ØCDHOLE DIA.

LCB

HDØE

EE

XC + STROKE

LRM

ØMM


Bore Ø

Rod No. CB CD Ø +.002 -.000

E Ø

EE HD L LR min.

M Add Stroke

NPTF1 SAE2 LB P

1.501 (std) 0.75 0.502 1.88 3/8 6 1.60 0.75 0.56 0.50 3.56 1.19

2 0.75 0.502 1.88 3/8 6 1.60 0.75 0.56 0.50 3.94 1.192.00 ALL 1.25 0.752 2.38 1/2 8 2.04 1.25 0.88 0.75 4.81 1.932.50 ALL 1.25 0.752 3.00 1/2 8 2.37 1.25 0.88 0.75 5.25 1.883.25 ALL 1.50 1.002 3.88 3/4 12 2.81 1.50 1.13 1.00 6.00 2.064.00 ALL 2.00 1.377 4.61 3/4 12 3.20 2.13 1.81 1.38 6.50 2.505.00 ALL 2.50 1.752 5.75 3/4 12 3.79 2.25 1.88 1.75 7.12 2.566.00 ALL 2.50 2.002 7.00 1 16 4.58 2.50 2.13 2.00 8.37 3.007.00 ALL 3.00 2.502 8.00 11/4 20 5.11 3.00 2.63 2.50 9.00 3.258.00 ALL 3.00 3.002 9.25 11/4 20 5.76 3.25 3.00 2.75 9.50 3.25

Bore Ø

Rod No. MM Rod Ø

W Y Add Stroke

XC ZC

1.501 (std) 0.625 0.56 2.12 4.87 5.37

2 1.000 0.69 2.62 5.38 5.88

2.001 (std) 1.000 0.69 2.51 6.75 7.50

2 1.375 0.81 2.63 6.87 7.62

2.501 (std) 1.000 0.69 2.69 7.19 7.94

2 1.750 0.94 2.94 7.44 8.193 1.375 0.81 2.81 7.31 8.06

3.251 (std) 1.375 0.81 3.06 8.31 9.31

2 2.000 1.00 3.25 8.50 9.503 1.750 0.94 3.19 8.44 9.44

4.001 (std) 1.750 0.94 3.40 9.56 10.94

2 2.500 1.06 3.52 9.69 11.063 2.000 1.00 3.46 9.62 11.00

5.00

1 (std) 2.000 1.00 3.70 10.37 12.122 3.500 1.06 3.76 10.43 12.183 2.500 1.06 3.76 10.43 12.184 3.000 1.06 3.76 10.43 12.18

6.00

1 (std) 2.500 1.06 4.24 11.93 13.932 4.000 1.06 4.24 11.93 13.933 3.000 1.06 4.24 11.93 13.934 3.500 1.06 4.24 11.93 13.93

7.00

1 (std) 3.000 1.06 4.25 13.06 15.562 5.000 1.19 4.38 13.19 15.693 3.500 1.06 4.25 13.06 15.564 4.000 1.06 4.25 13.06 15.565 4.500 1.19 4.38 13.09 15.69

8.00

1 (std) 3.500 1.06 4.44 13.81 16.562 5.500 1.19 4.56 13.93 16.683 4.000 1.06 4.44 13.81 16.564 4.500 1.19 4.56 13.93 16.685 5.000 1.19 4.56 13.93 16.68


13



A

Cap Fixed Clevis Mounting StyleBB




CW CWCB

ØEHD

ZC + STROKEXC + STROKE

LB + STROKE

P + STROKEY

W L

EE

M

LR

ØMM

ØCDPIN DIA.

Bore Ø

Rod No. CB min.

CD1 Ø +.000 -.002

CW E Ø

EE HD L LR min.

M Add Stroke

NPTF2 SAE3 LB P

1.501 (std) 0.75 .501 0.50 1.88 3/8 6 1.60 0.75 0.56 0.50 3.56 1.19

2 0.75 .501 0.50 1.88 3/8 6 1.60 0.75 0.56 0.50 3.94 1.192.00 All 1.25 .751 0.50 2.38 1/2 8 2.04 1.25 0.88 0.75 4.81 1.932.50 All 1.25 .751 0.63 3.00 1/2 8 2.37 1.25 0.88 0.75 5.25 1.883.25 All 1.50 1.001 0.75 3.88 3/4 12 2.81 1.50 1.13 1.00 6.00 2.064.00 All 2.00 1.376 1.00 4.61 3/4 12 3.20 2.13 1.81 1.38 6.50 2.505.00 All 2.50 1.751 1.25 5.75 3/4 12 3.79 2.25 1.88 1.75 7.12 2.566.00 All 2.50 2.001 1.25 7.00 1 16 4.58 2.50 2.13 2.00 8.37 3.007.00 All 3.00 2.501 1.50 8.00 11/4 20 5.11 3.00 2.63 2.50 9.00 3.258.00 All 3.00 3.001 1.50 9.25 11/4 20 5.76 3.25 3.00 2.75 9.50 3.25

1 Diameter CD is the Pivot Pin diameter (included) 2 NPTFportsareavailableforno additional charge 3 SAE straight thread o-ring ports are standard

Bore Ø

Rod No. MM Rod Ø W Y Add Stroke

XC ZC

1.501 (std) 0.625 0.56 2.12 4.87 5.37

2 1.000 0.69 2.62 5.38 5.88

2.001 (std) 1.000 0.69 2.51 6.75 7.50

2 1.375 0.81 2.63 6.87 7.62

2.501 (std) 1.000 0.69 2.69 7.19 7.94

2 1.750 0.94 2.94 7.44 8.193 1.375 0.81 2.81 7.31 8.06

3.251 (std) 1.375 0.81 3.06 8.31 9.31

2 2.000 1.00 3.25 8.50 9.503 1.750 0.94 3.19 8.44 9.44

4.001 (std) 1.750 0.94 3.40 9.56 10.94

2 2.500 1.06 3.52 9.69 11.063 2.000 1.00 3.46 9.62 11.00

5.00

1 (std) 2.000 1.00 3.70 10.37 12.122 3.500 1.06 3.76 10.43 12.183 2.500 1.06 3.76 10.43 12.183 3.000 1.06 3.76 10.43 12.18

6.00

1 (std) 2.500 1.06 4.24 11.93 13.932 4.000 1.06 4.24 11.93 13.933 3.000 1.06 4.24 11.93 13.934 3.500 1.06 4.24 11.93 13.93

7.00

1 (std) 3.000 1.06 4.25 13.06 15.562 5.000 1.19 4.38 13.19 15.693 3.500 1.06 4.25 13.06 15.564 4.000 1.06 4.25 13.06 15.565 4.500 1.19 4.38 13.19 15.69

8.00

1 (std) 3.500 1.06 4.44 13.81 16.562 5.500 1.19 4.56 13.93 16.683 4.000 1.06 4.44 13.81 16.564 4.500 1.19 4.56 13.93 16.685 5.000 1.19 4.56 13.93 16.68

14




14

A

X

A

X

XL + STROKE

XL + STROKE

Mounting Information3

HeadEndMounting

Note:foradditionaldimensionsseeStyleBBmount.1 These thread dimensions match mating thread dimensions of an inch-size spherical rod eye with the same hole diameter as the cap end. Itmustbepurchasedseparately;seeSphericalBearingMountingAccessories page for detailed information.

Note: Dimension X is the maximum off-center mounting of the cylinder. To determine dimension X for various stroke lengths, multiply the distance between pivot pin holes by tangent of anglea.ForextendedpositionuseXL+2xSTROKE.

Table 1 — Dimensional and Mounting Data

CapEndMounting

Table 2 – Recommended maximum swivel angle on each side of the cylinder centerline.


Spherical Bearing Cap End MountingInchSizeBearingStyleSB

2 Dimension CD is the hole diameter.

P + STROKE

LB + STROKE L MA

HD

EX

ØEEE

NR

XC + STROKEZC + STROKE

WA

KKCB

Y

ØMM

ØCDHOLE DIA.

Bore Ø

Rod No. MM Rod

Ø

Thread A CB CD2 Ø +.0000 -.0005

EX L MA NR min.

W Y Add Stroke

Style 9A KK1

Style 7A KK1

XC ZC

1.501 (std) 0.625 7/16-20 — 0.75

0.38 0.5000 0.44 0.75 0.75 0.560.56 2.12 4.87 5.62

2 1.000 — 7/16-20 0.75 0.69 2.62 5.38 6.13

2.001 (std) 1.000 3/4-16 — 1.13

0.56 0.7500 0.66 1.25 1.00 1.060.69 2.51 6.75 7.75

2 1.375 — 3/4-16 1.13 0.81 2.63 6.87 7.87

2.501 (std) 1.000 3/4-16 — 1.13

0.56 0.7500 0.66 1.25 1.00 1.060.69 2.69 7.19 8.19

2 1.750 — 3/4-16 1.13 0.94 2.94 7.44 8.443 1.375 — 3/4-16 1.13 0.81 2.81 7.31 8.31

3.251 (std) 1.375 1-14 — 1.63

0.75 1.0000 0.88 1.50 1.25 1.310.81 3.06 8.31 9.56

2 2.000 — 1-14 1.63 1.00 3.25 8.50 9.753 1.750 — 1-14 1.63 0.94 3.19 8.44 9.69

4.001 (std) 1.750 11/4-12 — 2.00

1.00 1.3750 1.19 2.13 1.88 1.880.94 3.40 9.56 11.44

2 2.500 — 11/4-12 2.00 1.06 3.52 9.69 11.563 2.000 — 11/4-12 2.00 1.00 3.46 9.62 11.50

5.00

1 (std) 2.000 1 1/2-12 — 2.25

1.25 1.7500 1.53 2.25 2.50 1.94

1.00 3.70 10.37 12.872 3.500 — 1 1/2-12 2.25 1.06 3.76 10.43 12.933 2.500 — 1 1/2-12 2.25 1.06 3.76 10.43 12.934 3.000 — 1 1/2-12 2.25 1.06 3.76 10.43 12.93

6.00

1 (std) 2.500 17/8-12 — 3.00

1.50 2.0000 1.75 2.50 2.50 2.19

1.06 4.24 11.93 14.432 4.000 — 17/8-12 3.00 1.06 4.24 11.93 14.433 3.000 — 17/8-12 3.00 1.06 4.24 11.93 14.434 3.500 — 17/8-12 3.00 1.06 4.24 11.93 14.43

7.00SeeSBMMountonthenextpage

8.00

Bore Ø

Maximum Operating Pressure

(psi)4

1.50 1,5002.00 2,2002.50 1,4503.25 1,5004.00 1,8505.00 2,0006.00 1,800

SB Pressure Ratings

Note:Femalethreadedrodend is shown to accept the inch-size spherical rod eye accessory with a male thread.

4Pressure ratings are based on standard commercial bearingratings.Forspherical bearing mount rated to 3,000 psi, see the SBMMountonthenextpage.

3 See SphericalBearingMountingAccessoriespages for information on mounting accessories.

Note: Standard spherical bearing is maintenance-free (sealed) for hole diameters largerthan0.5000".

Bore Ø Head End Mounted Cap End MountedAngle a Tan. of a Angle a Tan. of a

1.50 2.00° 0.035 2.00° 0.0352.00 2.50° 0.044 4.50° 0.0792.50 2.50° 0.044 4.50° 0.0793.25 3.00° 0.052 3.00° 0.0524.00 2.50° 0.044 3.00° 0.0525.00 3.00° 0.052 3.00° 0.0526.00 3.00° 0.052 3.00° 0.052


15



AAlthoughthestandardSBMounthasderatedpressureratingsbelow3,000psi,theSBMMountisastandardspherical bearing mount rated at 3,000 psi. Note that

P + STROKE

LB + STROKE L MA

HD

EX

ØEEE

NR

XC + STROKEZC + STROKE

W

A

KKCB

Y

ØMM

ØCDHOLE DIA.

Note:foradditionaldimensions,seeStyleSBMount.Forrecommendedmaximumswivelangles,seeTable2andsketchon the previous page.1 These thread dimensions match mating thread dimensions of a

metric spherical rod eye with the same hole diameter as the cap end.Itmustbepurchasedseparately;seeSphericalBearingMountingAccessoriespageformetricsizesfordetailedinformation.

Table 1 — Dimensional and Mounting Data


theSBMMounthasslightlydifferentlugdimensionsandametricbearingsize.SeeSphericalBearingMountingAccessories page for metric size accessories.

2 Dimension CD is the hole diameter.

Note:Malethreadedrodendis shown to accept the metric spherical rod eye accessory with a female thread.Note: Standard spherical

bearing is maintenance-free (sealed).

Bore Ø

Rod No. MM Rod

Ø

A1 Thread Length (mm)

KK1 Thread

Style 7M Male

W Y Add Stroke Dimensions at cap end (mm)

XC ZC CB (mm)

CD2 Ø (mm)

EX (mm)

L (mm)

MA (mm)

NR min. (mm)

1.501 (std) 0.625 0.71(18) M14X1.5 0.56 2.12 5.11 6.25 0.51

(13)0.7874-.0005

(20 -.012)0.63 (16)

0.98 (25)

1.14 (29)

0.87 (22)2 1.000 0.71(18) M14X1.5 0.69 2.62 5.61 6.75

2.001 (std) 1.000 0.87(22) M16X1.5 0.69 2.51 6.72 8.02 0.67

(17)0.9843-.0005(25-.012)

0.79 (20)

1.22 (31)

1.30 (33)

1.10 (28)2 1.375 0.87(22) M16X1.5 0.81 2.63 6.84 8.14

2.501 (std) 1.000 1.10 (28) M20X1.5 0.69 2.69 7.43 9.01

0.75 (19)

1.1811-.0005(30 -.012)

0.87 (22)

1.50 (38)

1.57 (40)

1.38 (35)2 1.750 1.10 (28) M20X1.5 0.94 2.94 7.68 9.26

3 1.375 1.10 (28) M20X1.5 0.81 2.81 7.56 9.13

3.251 (std) 1.375 1.42(36) M27X2 0.81 3.06 8.70 10.67

0.91 (23)

1.5748-.0005(40-.012)

1.10 (28)

1.89 (48)

1.97 (50)

1.73 (44)2 2.000 1.42(36) M27X2 1.00 3.25 8.89 10.86

3 1.750 1.42(36) M27X2 0.94 3.19 8.83 10.80

4.001 (std) 1.750 1.77(45) M33X2 0.94 3.40 9.72 12.16

1.18 (30)

1.9685-.0005(50-.012)

1.38 (35)

2.28 (58)

2.44 (62)

2.13 (54)2 2.500 1.77(45) M33X2 1.06 3.52 9.84 12.28

3 2.000 1.77(45) M33X2 1.00 3.46 9.78 12.22

5.00

1 (std) 2.000 2.20(56) M42X2 1.00 3.70 10.95 14.101.50 (38)

2.3622-.0006(60-.015)

1.73 (44)

2.83 (72)

3.15 (80)

2.68 (68)

2 3.500 2.20(56) M42X2 1.06 3.76 11.01 14.163 2.500 2.20(56) M42X2 1.06 3.76 11.01 14.164 3.000 2.20(56) M42X2 1.06 3.76 11.01 14.16

6.00

1 (std) 2.500 2.48(63) M48X2 1.06 4.24 13.05 16.991.85 (47)

3.1496-.0006(80-.015)

2.17 (55)

3.62 (92)

3.94 (100)

3.46 (88)

2 4.000 2.48(63) M48X2 1.06 4.24 13.05 16.993 3.000 2.48(63) M48X2 1.06 4.24 13.05 16.994 3.500 2.48(63) M48X2 1.06 4.24 13.05 16.99

7.00

1 (std) 3.000 3.35(85) M64X3 1.06 4.25 14.63 18.57

2.24 (57)

3.9370-.0008(100 -.020)

2.76 (70)

4.57 (116)

4.72 (120)

4.37 (111)

2 5.000 3.35(85) M64X3 1.19 4.38 14.75 18.693 3.500 3.35(85) M64X3 1.06 4.25 14.63 18.574 4.000 3.35(85) M64X3 1.06 4.25 14.63 18.575 4.500 3.35(85) M64X3 1.19 4.38 14.75 18.69

8.00

1 (std) 3.500 3.35(85) M64X3 1.06 4.44 15.12 19.85

2.24 (57)

3.9370-.0008(100 -.020)

2.76 (70)

4.57 (116)

4.72 (120)

4.37 (111)

2 5.500 3.35(85) M64X3 1.19 4.56 15.25 19.973 4.000 3.35(85) M64X3 1.06 4.44 15.12 19.854 4.500 3.35(85) M64X3 1.19 4.56 15.25 19.975 5.000 3.35(85) M64X3 1.19 4.56 15.25 19.97

Spherical Bearing Cap End MountingMetricSizeBearingStyleSBM

16




16


Crosstube Cap End Mounting Style TT



EE

LT

HDØE

XC + STROKE

LB + STROKE

ZC + STROKE

P + STROKEY

W

ØPT

L

ØMM

ØCDHOLE DIA.

Bore Ø

Rod No. CD Ø +.002 -.000

E Ø

EE HD L LT PT Ø

Add Stroke

NPTF1 SAE2 LB P

1.501 (std) 0.752 1.88 3/8 6 1.60 0.63 2.38 1.25 3.56 1.19

2 0.752 1.88 3/8 6 1.60 0.63 2.38 1.25 3.94 1.192.00 All 0.752 2.38 1/2 8 2.04 0.63 2.88 1.25 4.81 1.932.50 All 1.002 3.00 1/2 8 2.37 0.75 3.50 1.50 5.25 1.883.25 All 1.252 3.88 3/4 12 2.81 0.94 4.38 1.88 6.00 2.064.00 All 1.377 4.61 3/4 12 3.20 1.00 5.13 2.00 6.50 2.505.00 All 1.752 5.75 3/4 12 3.79 1.38 6.25 2.75 7.12 2.566.00 All 2.002 7.00 1 16 4.58 1.50 7.50 3.00 8.37 3.007.00 All 2.502 8.00 11/4 20 5.11 1.88 8.50 3.75 9.00 3.258.00 All 3.002 9.25 11/4 20 5.76 2.00 9.75 4.00 9.50 3.25


Bore Ø

Rod No.

MM Rod Ø

W Y Add Stroke

XC ZC

1.501 (std) 0.625 0.56 2.12 4.75 5.37

2 1.000 0.69 2.62 5.25 5.88

2.001 (std) 1.000 0.69 2.51 6.13 6.75

2 1.375 0.81 2.63 6.25 6.87

2.501 (std) 1.000 0.69 2.69 6.69 7.44

2 1.750 0.94 2.94 6.94 7.693 1.375 0.81 2.81 6.81 7.56

3.251 (std) 1.375 0.81 3.06 7.75 8.69

2 2.000 1.00 3.25 7.94 8.883 1.750 0.94 3.19 7.88 8.81

4.001 (std) 1.750 0.94 3.40 8.44 9.44

2 2.500 1.06 3.52 8.56 9.563 2.000 1.00 3.46 8.50 9.50

5.00

1 (std) 2.000 1.00 3.70 9.49 10.872 3.500 1.06 3.76 9.55 10.933 2.500 1.06 3.76 9.55 10.934 3.000 1.06 3.76 9.55 10.93

6.00

1 (std) 2.500 1.06 4.24 10.93 12.432 4.000 1.06 4.24 10.93 12.433 3.000 1.06 4.24 10.93 12.434 3.500 1.06 4.24 10.93 12.43

7.00

1 (std) 3.000 1.06 4.25 11.94 13.812 5.000 1.19 4.38 12.06 13.943 3.500 1.06 4.25 11.94 13.814 4.000 1.06 4.25 11.94 13.815 4.500 1.19 4.38 12.06 13.94

8.00

1 (std) 3.500 1.06 4.44 12.56 14.562 5.500 1.19 4.56 12.68 14.683 4.000 1.06 4.44 12.56 14.564 4.500 1.19 4.56 12.68 14.685 5.000 1.19 4.56 12.68 14.68


17



A


Intermediate Fixed Trunnion MountingStyle DD

W

ØE

ØTD

UM

TMTL TL

ØUX

P + STROKEZJ + STROKE

LB + STROKEXI

YEE

HD

BD

R.125 MAX

ØMM

1 NPTFportsareavailablefornoadditionalcharge 2 SAE straight thread o-ring ports are standard 3 Toleranceis+.000/-.002

Bore Ø

Rod No.

BD E Ø

EE HD TD Ø +.000 -.001

TL TM UM UX Ø

Add Stroke

NPTF1 SAE2 LB P

1.501 (std) 1.38 1.88 3/8 6 1.60 1.000 1.00 3.00 5.00 3.00 3.56 1.19

2 1.38 1.88 3/8 6 1.60 1.000 1.00 3.00 5.00 3.00 3.94 1.192.00 All 1.75 2.38 1/2 8 2.04 1.375 1.38 3.50 6.25 3.50 4.81 1.932.50 All 1.75 3.00 1/2 8 2.37 1.375 1.38 4.00 6.75 4.00 5.25 1.883.25 All 2.25 3.88 3/4 12 2.81 1.750 1.75 5.00 8.50 5.00 6.00 2.064.00 All 2.50 4.61 3/4 12 3.20 2.000 2.00 5.50 9.00 5.50 6.50 2.505.00 All 3.00 5.75 3/4 12 3.79 2.500 2.50 7.00 10.50 7.00 7.12 2.566.00 All 3.50 7.00 1 16 4.58 3.000 3.00 8.50 12.50 8.50 8.37 3.007.00 All 4.00 8.00 11/4 20 5.11 3.5003 3.50 9.75 14.75 9.75 9.00 3.258.00 All 4.50 9.25 11/4 20 5.76 4.0003 4.00 11.00 17.00 11.00 9.50 3.25



4 Shorter net/working strokes are available with the use of a stop tube; however, the overall length of the cylinder will increase. To achieve a net/working stroke that is less than the minimum shown, specify the stop tube length as the minimum stroke in Table 2. Grossstroke(designatedinthemodelcode)willbethe combination of the stop tube length and net (working) stroke length. If shortest total cylinder length is required and a stop tube is unacceptable, consult the factory.

5 Cylinders with an XI dimension shorter than the standard minimum are available with a special modification; consult the factory.

6 Add this number to the stroke to determine the maximum allowable XI dimension with the standard rod extension (W dimension).

Bore Ø

Rod No.

MM Rod

Ø

W Y Min. Stroke4

Min. XI5

Add Stroke

Max. XI6

ZJ

1.501 (std) 0.625 0.56 2.12 3.03 4.25 1.19 4.12

2 1.000 0.69 2.62 3.03 4.75 1.69 4.63

2.001 (std) 1.000 0.69 2.51 3.12 4.95 2.00 5.50

2 1.375 0.81 2.63 3.12 5.07 2.12 5.62

2.501 (std) 1.000 0.69 2.69 2.98 5.13 2.13 5.94

2 1.750 0.94 2.94 2.98 5.38 2.38 6.193 1.375 0.81 2.81 2.98 5.25 2.25 6.06

3.251 (std) 1.375 0.81 3.06 3.61 5.87 2.31 6.81

2 2.000 1.00 3.25 3.61 6.06 2.50 7.003 1.750 0.94 3.19 3.61 6.00 2.44 6.94

4.001 (std) 1.750 0.94 3.40 3.52 6.33 2.96 7.44

2 2.500 1.06 3.52 3.52 6.46 3.08 7.563 2.000 1.00 3.46 3.52 6.40 3.02 7.50

5.00

1 (std) 2.000 1.00 3.70 3.88 6.89 3.07 8.122 3.500 1.06 3.76 3.88 6.95 3.13 8.183 2.500 1.06 3.76 3.88 6.95 3.13 8.184 3.000 1.06 3.76 3.88 6.95 3.13 8.18

6.00

1 (std) 2.500 1.06 4.24 4.46 7.87 3.62 9.432 4.000 1.06 4.24 4.46 7.87 3.62 9.433 3.000 1.06 4.24 4.46 7.87 3.62 9.434 3.500 1.06 4.24 4.46 7.87 3.62 9.43

7.00

1 (std) 3.000 1.06 4.25 5.10 8.38 3.38 10.062 5.000 1.19 4.38 5.10 8.51 3.51 10.193 3.500 1.06 4.25 5.10 8.38 3.38 10.064 4.000 1.06 4.25 5.10 8.38 3.38 10.065 4.500 1.19 4.38 5.10 8.51 3.51 10.19

8.00

1 (std) 3.500 1.06 4.44 5.54 8.81 3.31 10.562 5.500 1.19 4.56 5.54 8.94 3.44 10.683 4.000 1.06 4.44 5.54 8.81 3.31 10.564 4.500 1.19 4.56 5.54 8.94 3.44 10.685 5.000 1.19 4.56 5.54 8.94 3.44 10.68

18




18


Round Head Flange Mounting Style JStyleJP–withclosetolerancepilot



ØRD

RT

P + STROKEYF

WWT

HD

LG + STROKE

FD ± 2.5°

ØFCØE

ØUC

ØFB EQUALLY

1.50"-6.00" BORE 6X ØFB7.00"-8.00" BORE 8X ØFB

ZG + STROKE

F

EEWF

ØMM

SPACED ON ØFC

Bore Ø

Rod No.

MM Rod

Ø

RT W WF WT YF Add Stroke

ZG

1.501 (std) 0.625 0.25 0.56 1.19 0.81 2.75 4.75

2 1.000 0.63 0.69 1.69 1.31 3.25 5.25

2.001 (std) 1.000 0.25 0.69 1.38 0.94 3.26 6.25

2 1.375 0.25 0.81 1.50 1.06 3.38 6.37

2.501 (std) 1.000 0.25 0.69 1.44 0.94 3.44 6.69

2 1.750 0.25 0.94 1.69 1.19 3.69 6.943 1.375 0.25 0.81 1.56 1.06 3.56 6.81

3.251 (std) 1.375 0.25 0.81 1.69 1.06 3.82 7.56

2 2.000 0.25 1.00 1.88 1.25 4.00 7.753 1.750 0.25 0.94 1.81 1.19 3.94 7.69

4.001 (std) 1.750 0.25 0.94 1.94 1.19 4.14 8.19

2 2.500 0.25 1.06 2.06 1.31 4.27 8.313 2.000 0.25 1.00 2.00 1.25 4.21 8.25

5.00

1 (std) 2.000 0.31 1.00 2.19 1.31 4.45 8.872 3.500 0.31 1.06 2.25 1.37 4.51 8.933 2.500 0.31 1.06 2.25 1.37 4.51 8.934 3.000 0.31 1.06 2.25 1.37 4.51 8.93

6.00

1 (std) 2.500 0.38 1.06 2.44 1.44 4.99 10.182 4.000 0.38 1.06 2.44 1.44 4.99 10.183 3.000 0.38 1.06 2.44 1.44 4.99 10.184 3.500 0.38 1.06 2.44 1.44 4.99 10.18

7.00

1 (std) 3.000 0.38 1.06 2.44 1.44 5.25 11.062 5.000 0.38 1.19 2.56 1.56 5.38 11.193 3.500 0.38 1.06 2.44 1.44 5.25 11.064 4.000 0.38 1.06 2.44 1.44 5.25 11.065 4.500 0.38 1.19 2.56 1.56 5.38 11.19

8.00

1 (std) 3.500 0.50 1.06 2.69 1.56 5.44 11.562 5.500 0.50 1.19 2.81 1.69 5.56 11.683 4.000 0.50 1.06 2.69 1.56 5.44 11.564 4.500 0.50 1.19 2.81 1.69 5.56 11.685 5.000 0.50 1.19 2.81 1.69 5.56 11.68

Note:MountingStylesJ/JP,in1.50-6.00inchbores,has6equallyspacedboltholesinthemounting flange. The bolt pattern is oriented to allow clearance for assembling mounting bolts when ports or switches are in positions 1 and/or 3. This bolt pattern orientation puts one hole each at positions 2 and 3, which results in bolt interference with ports or switches specified there. Consequently, ports or switches are not available inposition2or4ontheheadendofmountingStyles J/JP.

Installations that require a switch and port(s) located 90 degrees apart, on the head end of mounting Styles J/JP, can be accommodated by welding the flange with the mounting bolt pattern rotated slightly or with a special bolt size and quantity. Contact the factory in these cases.


Bore Ø

E Ø

EE F FB Ø

FC Ø

FD HD RD Ø UC Ø

Add Stroke

NPTF2 SAE3 Style J Style JP +.000 / -.002

LG P

1.50 1.88 3/8 6 0.38 0.28 2.75 30° 1.60 1.88 1.810 3.38 3.94 1.192.00 2.38 1/2 8 0.44 0.34 3.31 30° 2.04 2.38 2.310 4.00 5.31 1.932.50 3.00 1/2 8 0.50 0.41 4.13 30° 2.37 3.00 2.936 5.00 5.75 1.883.25 3.88 3/4 12 0.63 0.53 5.25 30° 2.81 3.88 3.810 6.38 6.50 2.064.00 4.61 3/4 12 0.75 0.66 6.25 30° 3.20 4.61 4.560 7.63 7.00 2.505.00 5.75 3/4 12 0.88 0.78 7.50 30° 3.79 5.75 5.686 9.00 7.55 2.566.00 7.00 1 16 1.00 0.91 9.13 30° 4.58 6.99 6.936 10.94 8.75 3.007.00 8.00 11/4 20 1.00 0.91 10.13 22.5° 5.11 7.99 7.936 11.94 9.63 3.258.00 9.25 11/4 20 1.13 1.06 11.63 22.5° 5.76 9.24 9.186 13.75 10.00 3.25


19



A


Round Cap Flange Mounting Style H

LH + STROKE

FZF + STROKE

XF + STROKE

Y P + STROKE

W

ØE

ØUC

ØFC

FD ± 2.5°

HD

EE

ØPDPEØMM

ØFB EQUALLY SPACED ON ØFC1.50"-6.00" BORE 6X ØFB7.00"-8.00" BORE 8X ØFBTable 1 – Dimensional and Mounting Data


1 NPTFportsareavailableforno additional charge 2 SAE straight thread o-ring ports are standard

Bore Ø

Rod No. E Ø

EE F FB Ø

FC Ø

FD HD PD3 Ø

UC Ø

Add Stroke

NPTF1 SAE2 LH P

1.501 (std) 1.88 3/8 6 0.38 0.28 2.75 30° 1.60 1.50 3.38 3.44 1.19

2 1.88 3/8 6 0.38 0.28 2.75 30° 1.60 1.50 3.38 3.81 1.192.00 All 2.38 1/2 8 0.44 0.34 3.31 30° 2.04 2.00 4.00 4.69 1.932.50 All 3.00 1/2 8 0.50 0.41 4.13 30° 2.37 2.50 5.00 5.13 1.883.25 All 3.88 3/4 12 0.63 0.53 5.25 30° 2.81 3.25 6.38 5.88 2.064.00 All 4.61 3/4 12 0.75 0.66 6.25 30° 3.20 4.00 7.63 6.37 2.505.00 All 5.75 3/4 12 0.88 0.78 7.50 30° 3.79 5.00 9.00 6.99 2.566.00 All 7.00 1 16 1.00 0.91 9.13 30° 4.58 6.00 10.94 8.25 3.007.00 All 8.00 11/4 20 1.00 0.91 10.13 22.5° 5.11 7.00 11.94 8.88 3.258.00 All 9.25 11/4 20 1.13 1.06 11.63 22.5° 5.76 8.00 13.75 9.37 3.25

Bore Ø

Rod No. MM Rod Ø

W Y Add Stroke

XF ZF

1.50 1 (std) 0.625 0.56 2.12 4.00 4.372 1.000 0.69 2.62 4.50 4.88

2.00 1 (std) 1.000 0.69 2.51 5.38 5.812 1.375 0.81 2.63 5.50 5.94

2.501 (std) 1.000 0.69 2.69 5.81 6.31

2 1.750 0.94 2.94 6.06 6.563 1.375 0.81 2.81 5.94 6.44

3.251 (std) 1.375 0.81 3.07 6.69 7.31

2 2.000 1.00 3.25 6.88 7.503 1.750 0.94 3.19 6.81 7.44

4.001 (std) 1.750 0.94 3.39 7.31 8.06

2 2.500 1.06 3.52 7.44 8.193 2.000 1.00 3.46 7.37 8.12

5.00

1 (std) 2.000 1.00 3.70 7.99 8.872 3.500 1.06 3.76 8.05 8.933 2.500 1.06 3.76 8.05 8.934 3.000 1.06 3.76 8.05 8.93

6.00

1 (std) 2.500 1.06 4.24 9.31 10.312 4.000 1.06 4.24 9.31 10.313 3.000 1.06 4.24 9.31 10.314 3.500 1.06 4.24 9.31 10.31

7.00

1 (std) 3.000 1.06 4.25 9.94 10.942 5.000 1.19 4.38 10.06 11.063 3.500 1.06 4.25 9.94 10.944 4.000 1.06 4.25 9.94 10.945 4.500 1.19 4.38 10.06 11.06

8.00

1 (std) 3.500 1.06 4.44 10.43 11.562 5.500 1.19 4.56 10.56 11.683 4.000 1.06 4.44 10.43 11.564 4.500 1.19 4.56 10.56 11.685 5.000 1.19 4.56 10.56 11.68

3 ØPD may be used to help center the cylinder during installation. However, typical cylinder assembly tolerances may require repositioning of the cylinder in order to align its travel with the load movement.

Note:MountingStyleH,in1.50-6.00inchbores,has6equallyspacedboltholesinthemountingflange. The bolt pattern is oriented to allow clear-ance for assembling mounting bolts when ports or switches are in positions 1 and/or 3. This bolt pattern orientation puts one hole each at positions 2 and 3, which results in bolt interference with ports or switches specified there. Consequently, ports or switches are not available in position 2 or 4onthecapendofmountingStyleH.

Installations that require a switch and port(s) located 90 degrees apart, on the cap end of mounting Style H, can be accommodated by welding the flange with the mounting bolt pattern rotated slightly or with a special bolt size and quantity. Contact the factory in these cases.

20




20

Double Rod Models – 1.50" to 8.00" Bore

To determine the dimensions for a double rod cylinder, first refer to the desired mounting style of the single rod version, as seen in the preceding pages of this catalog. When you have the required dimensions from that drawing, return to this page to supplement and replace the single rod dimensions with those shown on the double rod drawing and table above. Note that double rod cylinders haveaheadatbothendsandthatdimensionLDreplacesLB,andLGKreplacesLG.Thedoubleroddimensionsdiffer from, or are in addition to those for single rod

cylinders shown on preceding pages and provide the information needed to completely dimension a double rod cylinder. In the table above, note the minimum stroke length per mounting style.

On a double rod cylinder where the two rod ends are different, be sure to clearly state which rod end is to be assembled at which end. Port position 1 is standard. If otherthanstandard,specifyposition2,3or4whenviewed from rod end #1 only. See Port information page for more details.

How to Use Double Rod Cylinder Drawing Dimensions

Rod End #1 Rod End #2

Double Rod CylinderStylesKT&KDD

LD + STROKEWPK + STROKEY

ZM + 2 X STROKE

EE

ØMM MMØ

Table 1 – Dimensional and Mounting DataBore

ØRod No.

MM Rod

Ø

EE W PK Styles KJ / KJP All Other MountsWF WT YF LJ ZN Y LD ZM

NPTF SAE Add Stroke

Add Stroke

Add 2X Stroke

Add Stroke

Add 2X Stroke

1.50 1 (std) 0.625 3/8 6 0.56 1.22 1.19 0.81 2.87 4.78 6.10 2.12 4.34 5.482 1.000 3/8 6 0.69 1.22 1.69 1.31 3.37 4.78 7.10 2.62 5.09 6.48

2.00 1 (std) 1.000 1/2 8 0.69 1.76 1.38 0.94 3.26 6.09 7.53 2.51 5.40 6.782 1.375 1/2 8 0.81 1.76 1.50 1.06 3.38 6.09 7.78 2.63 5.40 7.03

2.501 (std) 1.000 1/2 8 0.69 1.90 1.44 0.94 3.44 6.78 8.03 2.69 5.90 7.28

2 1.750 1/2 8 0.94 1.90 1.69 1.19 3.69 6.78 8.53 2.94 5.90 7.783 1.375 1/2 8 0.81 1.90 1.56 1.06 3.56 6.78 8.28 2.81 5.90 7.53

3.251 (std) 1.375 3/4 12 0.81 2.02 1.69 1.06 3.82 7.59 8.90 3.07 6.53 8.15

2 2.000 3/4 12 1.00 2.02 1.88 1.25 4.00 7.59 9.28 3.25 6.53 8.533 1.750 3/4 12 0.94 2.02 1.81 1.19 3.94 7.59 9.16 3.19 6.53 8.41

4.001 (std) 1.750 3/4 12 0.94 2.35 1.94 1.19 4.14 8.10 9.91 3.39 7.27 9.16

2 2.500 3/4 12 1.06 2.35 2.06 1.31 4.27 8.10 10.15 3.52 7.27 9.403 2.000 3/4 12 1.00 2.35 2.00 1.25 4.21 8.10 10.03 3.46 7.27 9.28

5.00

1 (std) 2.000 3/4 12 1.00 2.50 2.19 1.31 4.45 8.70 10.66 3.70 7.90 9.912 3.500 3/4 12 1.06 2.50 2.25 1.37 4.51 8.70 10.78 3.76 7.90 10.033 2.500 3/4 12 1.06 2.50 2.25 1.37 4.51 8.70 10.78 3.76 7.90 10.034 3.000 3/4 12 1.06 2.50 2.25 1.37 4.51 8.70 10.78 3.76 7.90 10.03

6.00

1 (std) 2.500 1 16 1.06 2.79 2.44 1.44 4.99 10.02 12.03 4.24 9.15 11.282 4.000 1 16 1.06 2.79 2.44 1.44 4.99 10.02 12.03 4.24 9.15 11.283 3.000 1 16 1.06 2.79 2.44 1.44 4.99 10.02 12.03 4.24 9.15 11.284 3.500 1 16 1.06 2.79 2.44 1.44 4.99 10.02 12.03 4.24 9.15 11.28

7.00

1 (std) 3.000 11/4 20 1.06 3.16 2.44 1.44 5.25 10.97 12.67 4.25 9.54 11.672 5.000 11/4 20 1.19 3.16 2.56 1.56 5.38 10.97 12.92 4.38 9.54 11.923 3.500 11/4 20 1.06 3.16 2.44 1.44 5.25 10.97 12.67 4.25 9.54 11.674 4.000 11/4 20 1.06 3.16 2.44 1.44 5.25 10.97 12.67 4.25 9.54 11.675 4.500 11/4 20 1.19 3.16 2.56 1.56 5.38 10.97 12.92 4.38 9.54 11.92

8.00

1 (std) 3.500 11/4 20 1.06 3.21 2.69 1.56 5.44 11.46 13.09 4.44 9.96 12.092 5.500 11/4 20 1.19 3.21 2.81 1.69 5.56 11.46 13.34 4.56 9.96 12.343 4.000 11/4 20 1.06 3.21 2.69 1.56 5.44 11.46 13.09 4.44 9.96 12.094 4.500 11/4 20 1.19 3.21 2.81 1.69 5.56 11.46 13.34 4.56 9.96 12.345 5.000 11/4 20 1.19 3.21 2.81 1.69 5.56 11.46 13.34 4.56 9.96 12.34

EEWF

W

YFZN + 2 X STROKE

LJ + STROKE

PK + STROKE

WT

ØMM MMØ

StylesKJ/KJP

Rod End #1 Rod End #2

EEWF

W

YFZN + 2 X STROKE

LJ + STROKE

PK + STROKE

WT

ØMM MMØ


21



B

Cylinder Mounting Accessories

Rod End AccessoriesAccessories offered for the rod end of the cylinder include: RodClevis,EyeBracket,Knuckle,ClevisBracketandPivot Pin. To select the proper part number for any desired rod mounted accessory, refer to the table below and look opposite the thread size of the rod end as indicated in thefirstcolumn.ThePivotPins,EyeBracketsandClevisBracketsarelistedoppositethepindiameterthatfitstheirmatingKnucklesorClevises.

1 Includes pivot pin. 2CylinderaccessorydimensionsconformtoANSI/NFPA/T3.6.8R3-20103 CylinderaccessorydimensionsconformtoANSI/NFPA/T3.6.8R1-1984

Forged Steel or Cast Ductile Iron Mounting Plate or Eye Bracket Dimensions4

Thread Size

Pin Ø

Rod Clevis Mounting Plate or Eye Bracket Pivot PinPart

NumberLoad

Capacity (lb)

Forged Steel or Cast Ductile Iron

Fabricated Steel PartNumber

Shear Capacity

(lb) PartNumber

Load Capacity (lb)

PartNumber

Load Capacity (lb)

5/16-24 0.312 05122100001 2600 0959810031 1850 0740770000 1700 – –7/16-20 0.500 0509400000 4250 09598100502 4620 0691950000 4100 0683680000 86001/2-20 0.500 0509410000 4900 09598100502 4620 0691950000 4100 0683680000 86003/4-16 0.750 0509420000 11200 09598100752 12370 0691960000 10500 0683690000 193003/4-16 0.750 1332840000 11200 09598100752 12370 0691960000 10500 0683690000 193007/8-14 1.000 0509430000 18800 09598101002 20450 08536100003 20400 0683700000 343001-14 1.000 0509440000 19500 09598101002 20450 08536100003 20400 0683700000 343001-14 1.000 1332850000 19500 09598101002 20450 08536100003 20400 0683700000 34300

11/4-12 1.375 0509450000 33500 0959810138 33500 0691980000 21200 0683710000 6500011/4-12 1.375 1332860000 33500 0959810138 33500 0691980000 21200 0683710000 650001 1/2-12 1.750 0509460000 45600 0959810175 49480 08536200003 43300 0683720000 10520013/4-12 2.000 0509470000 65600 09598102002 70100 08536300003 70000 0683730000 13740017/8-12 2.000 0509480000 65600 09598102002 70100 08536300003 70000 0683730000 13740021/4-12 2.500 0509490000 98200 09598102502 98200 08536400003 94200 0683740000 2147002 1/2-12 3.000 0509500000 98200 09598103002 121940 08536500003 121900 0683750000 30920023/4-12 3.000 0509510000 98200 09598103002 121940 08536500003 121900 0683750000 30920031/4-12 3.500 0509520000 156700 0959810350 187910 0735380000 57400 0735450000 4209003 1/2-12 4.000 0509530000 193200 0959810400 268000 0735390000 75000 0735470000 5658004-12 4.000 0509540000 221200 0959810400 268000 0735390000 75000 0735470000 565800

ØCD

CB

ØDD(4X)LR

M

FL

F

Approx.20°

±.001

RE

RE

Cast or Forged Part Number6

Pin Ø

CB CD Ø

DD Ø

E (As

Cast)

F FL LR M (As

Cast)

R For Use With BB Mount Per Bore

0959810031 0.312 0.31 0.314 0.27 2.25 0.38 1.00 0.59 0.38 1.75 –0959810050 0.500 0.75 0.503 0.41 2.50 0.38 1.13 0.69 0.50 1.63 1.500959810075 0.750 1.25 0.753 0.53 3.50 0.63 1.88 1.13 0.75 2.55 Seefootnote70959810100 1.000 1.50 1.003 0.66 4.50 0.88 2.38 1.37 1.00 3.25 2.500959810138 1.375 2.00 1.378 0.66 5.00 1.005 3.00 1.88 1.38 3.82 3.250959810175 1.750 2.50 1.753 0.91 6.50 1.255 3.38 2.13 1.75 4.95 4.000959810200 2.000 2.50 2.003 1.06 7.50 1.50 4.00 2.38 2.00 5.73 5.000959810250 2.500 3.00 2.503 1.19 8.50 1.75 4.75 2.88 2.50 6.58 6.000959810300 3.000 3.00 3.003 1.31 9.50 2.00 5.25 3.13 3.00 7.50 7.000959810350 3.500 4.00 3.503 1.81 12.63 2.50 6.50 3.88 3.50 9.62 8.000959810400 4.000 4.50 4.003 2.06 14.88 3.00 7.50 4.38 4.06 11.45 –

Accessory Load CapacityThe various accessories on this and the following pages have been load rated for your convenience. The load capacity, shown in the table below, is the recommended maximumloadforthataccessorybasedona4:1designfactorintension.(PivotPinisratedinshear.)Beforespecifying, compare the actual load or the tension (pull) force at maximum operating pressure of the cylinder with the load capacity of the accessory you plan to use. If load or pull force of cylinder exceeds load capacity of accessory, consult factory.

Note: Cast ductile iron eye brackets must not be welded in place.

4 When used to mate with the Rod Clevis, select by pin diameter in the table above.5ThesedimensionsvaryfromNFPAstandard.Fisincreasedby.13.SufficientLRclearanceremainsforfullswingarcwithParkercapcleviscylinders and rod clevises.

6EyeBracketswithpindiameters.312thru1.000areforgedsteel.EyeBracketswith1.375pindiameterandlargerarecastductileiron.7For2.00"Boreusepartnumber069196000M.




22


1. Pivot Pins are furnished with Clevis MountedCylindersasstandard.

2. Pivot Pins are furnished with (2) Retainer Rings.

3. Pivot Pins must be ordered as a separate item if to be used with Knuckles,RodClevises,or ClevisBrackets.

5When used to mate with the Rod Clevis, select by pin diameter in table on previous page.

Fabricated Steel Mounting Plate or Eye Bracket Dimensions5

MR

LR

RE

F

M 25°

FL

CB

±.001

RE

ØCDØDD(X4)

CBCW CWER

KK Thread

±.001ØCD

A

CE

Rod Clevis Dimensions Pivot Pin Dimensions

CL

ØCD+.001-.002

1RodClevis’withpindiameters.312thru1.375areforgedsteel.RodClevis’with1.750pindiametersandlargerarecastductileiron.

2 Includes Pivot Pin3 Consult appropriate cylinder rod end dimensions for compatibility.

4This size supplied with cotter pins.

Part Number1 Pin Ø

A CB CDØ

CE CW ER KKThread

05122100002 0.312 0.81 0.34 0.314 2.25 0.20 0.30 5/16-240509400000 0.500 0.75 0.77 0.503 1.50 0.49 0.50 7/16-200509410000 0.500 0.75 0.77 0.503 1.50 0.49 0.50 1/2-200509420000 0.750 1.13 1.27 0.753 2.13 0.62 0.75 3/4-161332840000 0.750 1.13 1.27 0.753 2.38 0.62 0.75 3/4-160509430000 1.000 1.63 1.52 1.003 2.94 0.74 1.00 7/8-140509440000 1.000 1.63 1.52 1.003 2.94 0.74 1.00 1-141332850000 1.000 1.63 1.52 1.003 3.13 0.74 1.00 1-140509450000 1.375 1.88 2.04 1.378 3.75 0.99 1.38 11/4-121332860000 1.375 2.00 2.04 1.378 4.13 0.99 1.38 11/4-120509460000 1.750 2.25 2.54 1.753 4.50 1.24 1.75 1 1/2-120509470000 2.000 3.00 2.54 2.003 5.50 1.24 2.00 13/4-120509480000 2.000 3.00 2.54 2.003 5.50 1.24 2.00 17/8-120509490000 2.500 3.50 3.04 2.503 6.50 1.49 2.50 21/4-120509500000 3.000 3.50 3.04 3.003 6.75 1.49 2.75 2 1/2-120509510000 3.000 3.50 3.04 3.003 6.75 1.49 2.75 23/4-120509520000 3.500 3.503 4.04 3.503 7.75 1.98 3.50 31/4-120509530000 4.000 4.003 4.54 4.003 8.81 2.23 4.00 3 1/2-120509540000 4.000 4.003 4.54 4.003 8.81 2.23 4.00 4-12

Part Number CD Ø

CL

0683680000 0.500 1.880683690000 0.750 2.630683700000 1.000 3.130683710000 1.375 4.190683720000 1.750 5.190683730000 2.000 5.190683740000 2.500 6.190683750000 3.000 6.250735450000 3.500 8.2507354700004 4.000 9.00

Fabricated Steel Part Number

Pin Ø

CB CD Ø

DD Ø

E F FL LR M MR R For Use With BB Mount Per Bore

0740770000 0.312 0.31 0.314 0.27 2.25 0.38 1.00 0.63 0.38 0.50 1.75 –0691950000 0.500 0.75 0.503 0.41 2.50 0.38 1.13 0.75 0.50 0.56 1.63 1.50069196000M 0.750 1.06 0.753 0.53 3.50 0.63 1.88 1.25 0.75 0.88 2.55 2.000691960000 0.750 1.25 0.753 0.53 3.50 0.63 1.88 1.25 0.75 0.88 2.55 2.500853610000 1.000 1.50 1.003 0.66 4.50 0.88 2.38 1.50 1.00 1.25 3.25 3.250691980000 1.375 2.00 1.378 0.66 5.00 0.88 3.00 2.13 1.38 1.63 3.82 4.000853620000 1.750 2.50 1.753 0.91 6.50 1.13 3.38 2.25 1.75 2.13 4.95 5.000853630000 2.000 2.50 2.003 1.06 7.50 1.50 4.00 2.50 2.00 2.44 5.73 6.000853640000 2.500 3.00 2.503 1.19 8.50 1.75 4.75 3.00 2.50 3.00 6.58 7.000853650000 3.000 3.00 3.003 1.31 9.50 2.00 5.25 3.25 2.75 3.25 7.50 8.000735380000 3.500 4.00 3.503 1.81 12.63 1.69 5.69 4.00 3.50 4.13 9.62 –0735390000 4.000 4.50 4.003 2.06 14.88 1.94 6.44 4.50 4.00 5.25 11.45 –


23



B


Accessory Load CapacityThe various accessories have been load rated for your convenience. The load capacity, shown in the table below, is the recommended maximum load for that accessory basedona4:1designfactorintension.(PivotPinisratedinshear.)Beforespecifying,comparetheactualloadorthe tension (pull) force at the maximum operating pressure of the cylinder with the load capacity of the accessory you plan to use. If load or pull force of cylinder exceeds load capacity of accessory, consult factory.

1 This size supplied with cotter pins.

Forged Steel or Cast Ductile Iron Clevis Bracket Dimensions

Rod End Accessories Accessories offered for the rod end of the cylinder includeRodClevis,EyeBracket,Knuckle,ClevisBracket,and Pivot Pin. To select the proper part number for any rod mounted accessory, refer to the table below and look in the row to the right of the rod thread in the first column.ThePivotPins,EyeBracketsandClevisBracketsare listed opposite the pin diameter that fits their mating KnucklesorClevises.

Thread Size

Pin Ø

Knuckle Clevis Bracket Pivot PinPart

NumberLoad

Capacity(lb)

Forged Steel or Cast Ductile Iron

Fabricated Steel PartNumber

Shear Capacity

(lb) PartNumber

Load Capacity (lb)

PartNumber

Load Capacity (lb)

5/16-24 0.438 0740750000 3300 0960160044 2830 0740760000 3600 0740780000 66007/16-20 0.500 0690890000 5000 0960160050 7740 0692050000 7300 0683680000 86001/2-20 0.500 0690900000 5700 0960160050 7740 0692050000 7300 0683680000 86003/4-16 0.750 0690910000 12100 0960160075 13600 0692060000 10880 0683690000 193007/8-14 1.000 0690920000 13000 0960160100 23000 0692070000 15180 0683700000 343001-14 1.000 0690930000 21700 0960160100 23000 0692070000 15180 0683700000 34300

11/4-12 1.375 0690940000 33500 0960160138 39500 0692080000 23560 0683710000 650001 1/2-12 1.750 0690950000 45000 0960160175 49480 0692090000 21520 0683720000 10520013/4-12 2.000 0690960000 53500 0960160200 72400 0692100000 26000 0692150000 13740017/8-12 2.000 0962160000 75000 0960160200 72400 0692100000 26000 0692150000 13740021/4-12 2.500 0962170000 98700 0960160250 98700 0692110000 28710 0683740000 2147002 1/2-12 3.000 0962180000 110000 0960160300 123300 0692120000 28190 0683750000 30920023/4-12 3.000 0962190000 123300 N/A N/A 0692130000 31390 0692160000 30920031/4-12 3.500 0962200000 161300 0960160350 200400 0735420000 80250 0735450000 4209003 1/2-12 3.500 0962210000 217300 0960160350 200400 0735420000 80250 0735450000 4209004-12 4.000 0962220000 273800 0960160400 292100 0735430000 98420 0821810000 565800N/A 4.000 N/A N/A N/A N/A N/A N/A 07354700001 565800

LR

RE

ØDD(X4)

F

M

FL

CW CWCB

±.001

RE

ØCD

Approx.20°

Cast or Forged Part Number2

Pin Ø

CB CD Ø

CW DD Ø

E (As

Cast)

F FL LR M (As

Cast)

R For Use With B Mount Per Bore

0960160044 0.438 0.46 0.440 0.37 0.27 2.25 0.38 1.00 0.56 0.44 1.75 –0960160050 0.500 0.78 0.503 0.50 0.41 2.50 0.38 1.13 0.63 0.56 1.63 1.500960160075 0.750 1.28 0.753 0.63 0.53 3.50 0.63 1.88 1.06 0.75 2.56 2.00,2.500960160100 1.000 1.53 1.003 0.75 0.66 4.50 0.75 2.25 1.25 1.00 3.25 3.250960160138 1.375 2.03 1.378 1.00 0.66 5.00 0.88 3.00 1.94 1.38 3.81 4.000960160175 1.750 2.53 1.753 1.25 0.91 6.50 0.94 3.13 2.00 1.75 4.94 5.000960160200 2.000 2.53 2.003 1.25 1.06 7.50 1.38 3.75 2.25 2.00 5.75 6.000960160250 2.500 3.03 2.503 1.50 1.19 8.50 1.50 4.50 2.81 2.50 6.59 7.000960160300 3.000 3.03 3.003 1.50 1.31 9.50 1.88 5.38 3.31 3.00 7.50 8.000960160350 3.500 4.03 3.503 2.00 1.81 12.63 2.31 6.38 3.88 3.50 9.62 –0960160400 4.000 4.53 4.003 2.25 2.06 14.88 2.88 7.50 4.50 4.00 11.50 –

Note: Cast ductile iron clevis brackets must not be welded in place.

2 ClevisBracketswithpindiameters.438thru1.000areforgedsteel.ClevisBracketswith1.375pinandlargerarecastductileiron.




24


Knuckle Dimensions Pivot Pin Dimensions

CL

ØCD+.001-.002

Fabricated Steel Clevis Bracket Dimensions

Part Number Pin Ø

A CA CB CD Ø

ER JL LR min

KK Thread

0740750000 0.438 0.75 1.50 0.43 0.440 0.53 – – 5/16-240690890000 0.500 0.75 1.50 0.75 0.503 0.59 – – 7/16-200690900000 0.500 0.75 1.50 0.75 0.503 0.59 – – 1/2-200690910000 0.750 1.13 2.06 1.25 0.753 0.87 – – 3/4-160690920000 1.000 1.13 2.38 1.50 1.003 1.15 – – 7/8-140690930000 1.000 1.63 2.81 1.50 1.003 1.15 – – 1-140690940000 1.375 2.00 3.44 2.00 1.378 1.55 – – 11/4-120690950000 1.750 2.25 4.00 2.50 1.753 1.96 – – 1 1/2-120690960000 2.000 2.25 4.38 2.50 2.003 2.24 – – 13/4-120962160000 2.000 3.00 5.00 2.50 2.003 2.24 3.00 2.77 17/8-120962170000 2.500 3.50 5.81 3.00 2.503 2.76 3.50 3.09 21/4-120962180000 3.000 3.50 6.13 3.00 3.003 3.30 4.00 3.58 2 1/2-120962190000 3.000 3.63 6.50 3.50 3.003 3.30 4.00 3.58 23/4-120962200000 3.500 4.50 7.63 4.00 3.503 3.87 6.00 4.18 31/4-120962210000 3.500 5.00 7.63 4.00 3.503 3.87 6.00 4.18 3 1/2-120962220000 4.000 5.50 9.13 4.50 4.003 4.43 6.00 4.80 4-12

Part Number CD Ø CL

0740780000 0.438 1.310683680000 0.500 1.880683690000 0.750 2.630683700000 1.000 3.130683710000 1.375 4.190683720000 1.750 5.190692150000 2.000 5.690683740000 2.500 6.190683750000 3.000 6.250692160000 3.000 6.750735450000 3.500 8.250821810000 4.000 8.6907354700001 4.000 9.00


Pin Ø

CB CD Ø

CW DD Ø

E F FL LR M MR R For Use With B Mount Per Bore

0740760000 0.438 0.46 0.440 0.38 0.27 2.25 0.38 1.00 0.63 0.38 0.50 1.75 –0692050000 0.500 0.80 0.503 0.50 0.41 3.50 0.50 1.50 0.75 0.50 0.63 2.55 1.500692060000 0.750 1.30 0.753 0.63 0.53 5.00 0.63 1.88 1.19 0.75 0.91 3.82 2.00,2.500692070000 1.000 1.59 1.003 0.75 0.66 6.50 0.75 2.25 1.50 1.00 1.25 4.95 3.250692080000 1.375 2.09 1.378 1.00 0.66 7.50 0.88 3.00 2.00 1.38 1.66 5.73 4.000692090000 1.750 2.59 1.753 1.25 0.91 9.50 0.88 3.63 2.75 1.75 2.22 7.50 5.000692100000 2.000 2.59 2.003 1.50 1.06 12.75 1.00 4.25 3.19 2.25 2.78 9.40 6.000692110000 2.500 3.09 2.503 1.50 1.19 12.75 1.00 4.50 3.50 2.50 3.13 9.40 7.000692120000 3.000 3.09 3.003 1.50 1.31 12.75 1.00 6.00 4.25 3.00 3.59 9.40 8.000692130000 3.000 3.59 3.003 1.50 1.31 12.75 1.00 6.00 4.25 3.00 3.59 9.40 –0735420000 3.500 4.09 3.503 2.00 1.81 15.50 1.69 6.69 5.00 3.50 4.13 12.00 –0735430000 4.000 4.59 4.003 2.00 2.06 17.50 1.94 7.69 5.75 4.00 4.88 13.75 –

1. Pivot Pins are furnished with Clevis MountedCylindersasstandard.

2. Pivot Pins are furnished with (2) Retainer Rings.

3. Pivot Pins must be ordered as a separate item if to be used with Knuckles,RodClevises,or ClevisBrackets.

1 This size supplied with cotter pins.

CD

CALR Min.

ØCD

ER Max.

JL

A KK Thread

CB

±.001±.001

CB

CA

CD

ER Max.

AKK Thread

ØCD

Thread Size thru 1 3/4-12 Thread Size 1 7/8-12 & Larger

25°MR

LR

RE

ØDD(X4)

F

M

FL

CW CWCB

±.001

RE

ØCD


25



B

Spherical Bearing Mounting Accessories

LE

ØCD

JK Thd

ER (Max)

LubeFitting

CE

A

EX

ØJL

Pivot Pin (Inch Sizes)

Pivot Pins are furnished with (2) Retainer Rings.

Accessories for spherical bearing mount cylinders include Spherical Rod Eyes, Pivot Pins and Clevis

Brackets.Toidentifytheproperpartnumberforthedesired accessory, see the tables below.

Spherical Rod Eye (Inch Sizes)

MR

LR

RE

F

M

FL

CW CWCF

RE

ØCD

ØDD(4 X)

±.001

CL

ØCD

Clevis Bracket for SB Mount Cap or Spherical Rod Eye (Inch Sizes)

Bore Ø

Part No. A CD Ø +.0000 -.0005

CE ER EX JK Thread

Size

JL Ø

LE Load Capacity (lb)

1.50 0961000050 0.72 0.5000 0.86 0.80 0.44 7/16-20 0.88 0.78 26442.00

0961000075 1.02 0.7500 1.25 1.14 0.66 3/4-16 1.31 1.06 94412.503.25 0961000100 1.52 1.0000 1.88 1.34 0.88 1-14 1.50 1.45 168604.00 0961000138 2.02 1.3750 2.13 1.67 1.19 11/4-12 2.00 1.91 285625.00 0961000175 2.14 1.7500 2.50 2.05 1.53 1 1/2-12 2.00 2.16 430056.00 0961000200 2.89 2.0000 2.75 2.60 1.75 17/8-12 2.75 2.50 70193

Bore Ø

Part No. CD Ø

CL Shear Capacity (lb)

1.50 0839620000 .4997-.0004 1.56 86002.00

0839630000 .7497-.0005 2.03 193002.503.25 0839640000 .9997-.0005 2.50 343004.00 0839650000 1.3746-.0006 3.31 650005.00 0839660000 1.7496-.0006 4.22 1052006.00 0839670000 1.9996-.0007 4.94 137400

Note:Standardsphericalbearingismaintenance-free(sealed)forCDØ>0.5000"

BoreØ

PinØ

Cast Ductile Iron Part Number


CDØ

CF CW DDØ

E F FL LR M MR R Load Capacity (lb)

1.50 0.500 0959450000 0839470000 0.503 0.45 0.50 0.41 3.00 0.50 1.50 0.94 0.50 0.63 2.05 57702.00

0.750 0959300000 0839480000 0.753 0.67 0.63 0.53 3.75 0.63 2.00 1.38 0.88 1.00 2.76 94502.503.25 1.000 0959310000 0839490000 1.003 0.89 0.75 0.53 5.50 0.75 2.50 1.69 1.00 1.19 4.10 143004.00 1.375 0959320000 0839500000 1.378 1.20 1.00 0.66 6.50 0.88 3.50 2.44 1.38 1.63 4.95 203225.00 1.750 0959330000 0839510000 1.753 1.55 1.25 0.91 8.50 1.25 4.50 2.88 1.75 2.06 6.58 378006.00 2.000 0959340000 0839520000 2.003 1.77 1.50 0.91 10.63 1.50 5.00 3.00 2.00 2.38 7.92 50375

FabricatedSteel

±.001

RE

F

FL

M

RE

ØCD

CFCW CW

ØDD(4X)

LR

Cast Ductile Iron

Order to fit Piston Rod Thread Size




26

Spherical Bearing Mounting Accessories

Accessories for spherical bearing mount cylinders include Spherical Rod Eyes, Pivot Pins and Clevis

Brackets.Toidentifytheproperpartnumberforthedesired accessory, see the tables below.

Bore Ø

Part No.

A max

AX min

CH CN EF max

EN EU KK LF min

MA max Nm

N max

P Load Cap. (lb)

1.50 1452560000 55 19 58 20 -0.012 27.5 16 -.012 13 M14x1.5 25 25 25 M8 44962.00 1452570000 62 23 68 25 -0.012 32.5 20 -.012 17 M16x1.5 30 25 30 M8 71942.50 1452580000 80 29 85 30 -0.012 40 22 -.012 19 M20x1.5 35 45 36 M10 112403.25 1452590000 90 37 105 40 -0.012 50 28 -.012 23 M27x2 45 45 45 M10 179854.00 1452600000 105 46 130 50 -0.012 62.5 35 -.012 30 M33x2 58 80 55 M12 281015.00 1452610000 134 57 150 60 -0.015 80 44 -.015 38 M42x2 68 160 68 M16 449626.00 1452620000 156 64 185 80 -0.015 102.5 55 -.015 47 M48x2 92 310 90 M20 71939

7.00,8.00 1452630000 190 86 240 100 -0.020 120 70 -.020 57 M64x3 116 530 110 M24 112404

CH

LF

EF

PMA Torque

3°

EU

EN

AX

A

N

KK

CN3°

Spherical Rod Eye (MetricSizes)

Note: Standard spherical bearing is maintenance-free (sealed)

All dimensions are in millimeters unless otherwise specified.

Clevis Bracket and Pin for Style SBM Cap or Spherical Rod Eye(MetricSizes)

TA

FM

KC

GLLO

CO

FO

SRCG

UK

RE

ØCF

LJLG

UJ

CP

ØHB

Bore Ø

Part No. CF Ø

K7/h6

CG +0.1, +0.3

CO N9

CP FM js11

FO js14

GL js13

HB Ø

KC 0, +0.30

LG LJ LO RE js13

SR max

TA js13

UJ UK Load Cap. (lb)

1.50 1455320000 20 16 16 50 55 20 64 14 4.3 39 40 80 85 20 58 120 90 44962.00 1455330000 25 20 25 60 65 22 78 16 5.4 48 49 98 100 25 70 140 110 71942.50 1455340000 30 22 25 70 85 24 97 18 5.4 62 63 120 115 30 90 160 135 112403.25 1455350000 40 28 36 80 100 24 123 22 8.4 72 73 148 135 40 120 190 170 179854.00 1455360000 50 35 36 100 125 35 155 30 8.4 90 92 190 170 50 145 240 215 281015.00 1455370000 60 44 50 120 150 35 187 39 11.4 108 110 225 200 60 185 270 260 449626.00 1455380000 80 55 50 160 190 35 255 45 11.4 140 142 295 240 80 260 320 340 71939

7.00,8.00 1455390000 100 70 63 200 210 35 285 48 12.4 150 152 335 300 100 300 400 400 112404


27



B

Linear Alignment Couplers

Linear Alignment Couplers are available in 19 standard thread sizesCost Saving Features and Benefits Include:

n Simplify cylinder installation and reduce assembly costs

n Lowermaintenancecostsfrompossible machine misalignment

Alignment Coupler See Table for Part Numbers and Dimensions

ØD

1/16

CE

NTE

RLI

NE

A THREADE DEEP

K

CE

ØF

M °

TO

TAL

MO

VE

ME

NT

A THREADØB

GACROSS FLATS

J

1/8

TOTA

LM

OV

EM

EN

T

HACROSS FLATS

How to Order Linear Alignment Couplers — When ordering a cylinder with a threaded male rod end, specify thecouplerofequalthreadsizebypartnumberaslistedinthetable.Forexample,PistonRod“KK”or“CC” dimensionis3/4"-16,specifycouplerpartnumber1347570075.

n Maximizereliabilityfortrouble-free operation, long life and lower operating costs

n Increase cylinder life by reducing wear on piston and rod bearings

Part Numbers and DimensionsPart No. A1

Thread Size

B Ø

C D Ø

E F Ø

G H J K M Max. Pull Load (lbs.)

Max. Approx. Weight (lbs.)

1347570031 5/16-24 1.13 1.75 0.94 0.50 0.50 0.38 0.75 0.38 0.94 6° 1200 .351347570038 3/8-24 1.13 1.75 0.94 0.50 0.50 0.38 0.75 0.38 0.94 6° 2425 .351347570044 7/16-20 1.38 2.00 1.13 0.75 0.63 0.50 0.88 0.38 1.09 6° 3250 .551347570050 1/2-20 1.38 2.00 1.13 0.75 0.63 0.50 0.88 0.38 1.09 6° 4450 .551347570063 5/8-18 1.38 2.00 1.13 0.75 0.63 0.50 0.88 0.38 1.09 6° 6800 .551347570075 3/4-16 2.00 2.31 1.63 1.13 0.94 0.75 1.31 0.44 1.28 6° 9050 1.41347570088 7/8-14 2.00 2.31 1.63 1.13 0.94 0.75 1.31 0.44 1.28 6° 14450 1.41347570100 1-14 3.13 3.00 2.38 1.63 1.44 1.25 1.88 0.75 1.78 6° 19425 4.81347570125 11/4-12 3.13 3.00 2.38 1.63 1.44 1.25 1.88 0.75 1.78 6° 30500 4.81337390125 11/4-12 3.50 4.00 2.00 2.00 1.50 1.25 1.69 0.75 2.50 10° 30500 6.91337390150 1 1/2-12 4.00 4.38 2.25 2.25 1.75 1.50 1.94 0.88 2.75 10° 45750 9.81337390175 13/4-12 4.00 4.38 2.25 2.25 1.75 1.50 1.94 0.88 2.75 10° 58350 9.81337390188 17/8-12 5.00 5.63 3.00 3.00 2.25 1.94 2.63 1.38 3.38 10° 67550 19.81337390200 2-12 5.00 5.63 3.00 3.00 2.25 1.94 2.63 1.38 3.38 10° 77450 19.81337390225 21/4-12 6.75 6.38 3.25 3.50 2.75 2.38 2.88 1.63 3.75 10° 99250 35.31337390250 2 1/2-12 7.00 6.50 4.00 3.50 3.25 2.88 3.38 1.63 3.88 10° 123750 45.31337390275 23/4-12 7.00 6.50 4.00 3.50 3.25 2.88 3.38 1.63 3.88 10° 150950 45.31337390300 3-12 7.00 6.50 4.00 3.50 3.25 2.88 3.38 1.63 3.88 10° 180850 45.31337390325 31/4-12 9.25 8.50 5.25 4.50 4.00 3.38 4.50 2.00 5.50 10° 218450 –1337390425 41/4-12 12.88 11.25 7.75 4.50 5.50 4.88 7.00 1.50 8.75 10° 370850 –

1 Metricthreadsizecouplersarealsoavailable,consultfactory.




28

Style 55 Piston Rod End Accessories

Rod A B C D E F Bolt Size Bolt Split Weld Ø Ø Ø Ø Circle Coupler Plate Part No. Part No. 0.625 1.50 2.00 0.50 0.56 .250 4 #10-24x.94LG 1.125 1472340062 1481740062 1.000 2.00 2.50 0.50 0.88 .250 6 1/4-20x1.25LG 1.500 1472340100 1481740100 1.375 2.50 3.00 0.63 1.00 .250 6 5/16-18x1.00LG 2.000 1472340138 1481740138 1.750 3.00 4.00 0.63 1.25 .250 8 5/16-18x1.75LG 2.375 1472340175 1481740175 2.000 3.50 4.00 0.75 1.63 .375 12 3/8-16x2.25LG 2.687 1472340200 1481740200 2.500 4.00 4.50 0.75 1.88 .375 12 3/8-16x2.50LG 3.187 1472340250 1481740250 3.000 5.00 5.50 1.00 2.38 .375 12 1/2-13x3.25LG 4.000 1472340300 1481740300 3.500 5.88 7.00 1.00 2.63 .375 12 5/8-11x3.50LG 4.687 1472340350 1481740350 4.000 6.38 7.00 1.00 2.63 .375 12 5/8-11x3.50LG 5.187 1472340400 1481740400 4.500 6.88 8.00 1.00 3.13 .375 12 5/8-11x4.00LG 5.687 1472340450 1481740450 5.000 7.38 8.00 1.00 3.13 .375 12 5/8-11x4.00LG 6.187 1472340500 1481740500 5.500 8.25 9.00 1.25 3.88 .375 12 3/4-10x5.00LG 6.875 1472340550 1481740550

Ø E

F BOLTS

STYLE 55 ROD ENDSPLIT COUPLER

WELD PLATE

DC

Ø BØ A

Part Numbers and Dimensions

Note:Boltsarenotincludedwithsplitcouplerorweldplate

Parker Style 55 Piston Rod EndSplit Couplers and Weld Plates

WARNING: Piston rod separation from the machine member can result in severe personal injury or even death to nearby personnel. The cylinder user must make sure the weld holding the weld plate to the machine is of sufficient quality and size to hold the intended load. The cylinder user must also make sure the bolts holding split coupler to the weld plate are of sufficient strength to hold the intended load and installed in such a way that they will not become loose during the machine’s operation.


29



B

Notes:Factoryassembledpistonrodassemblies(whichincludesealsforthespecifiedpistontype)are recommended. Do not remove the piston from the rod.

Cylindersratedforhightemperatures(SealCodesV,HandD)mayincludeasetscrewtolock the head to the cylinder body. Remove and replace it when servicing the cylinder.

Parts Identification / Tools

10

11

4 987

1214

2

563

13

1 16 16

15

18 19 19 417

3 32

Symbol Description1 Head2 Rod wiper3 Rod seal4 Rod wear ring1

5 End seal (o-ring)6 Backupringforendseal7 Piston rod (single rod type)8 Piston9 Piston seal energizer10 Piston seal11 Piston wear ring 12 Piston joint o-ring13 Piston rod nut2

14 Cylinder body (welded to cap)15 Cap (welded to cylinder body)16 Port (welded to cylinder body)17 Head (optional)3

18 Rod wiper energizer3,4

19 Rod seal energizer3

20 Magneticrings5

Cylinder Service Tool (Head Torquing)

Optional Mixed Media PistonOptional Extreme High

Temperature and Low Friction Head

8 11910

Optional Magnetic Piston

Optional Hi Load and Low Friction Piston

(Bronze Filled PTFE Seal)

8 910 11

108 119 20

1 Not used for 0.625"roddiameter2 Onlyfor1.50"to5.00"bores.For6.00"to8.00"bores,pistonsare

threaded and torqued to the piston rod, and set screws are used to lock the piston to the rod.

3 UsedforPistoncodeForSealcodeH4UsedforSealcodesMandD5UsedforPistoncode7

Spanner Hole Ø

Cylinder Service Tool

Head Torque Units

2 holes on head face

Fits standard square drive on torque wrench

USA Metric

Lb-Ft N-m

0.171 RDHSVCTL15 55 75

0.203 RDHSVCTL20 70 95

0.203 RDHSVCTL25 100 136

0.266 RDHSVCTL32 150 203

0.266 RDHSVCTL40 175 237

0.266 RDHSVCTL50 225 305

0.266 RDHSVCTL60 285 386

0.391 RDHSVCTL70 400 542

0.516 RDHSVCTL80 485 658

Parts Identification Torque Tool Specifications




30

Seal Class

Piston Code

Bore Diameter

1.50 2.00 2.50 3.25 4.001 B,7 PK151RDH01 PK201RDH01 PK251RDH01 PK321RDH01 PK401RDH01

1 K,F PK151RDHK1 PK201RDHK1 PK251RDHK1 PK321RDHK1 PK401RDHK1

1 W PK151RDHW1 PK201RDHW1 PK251RDHW1 PK321RDHW1 PK401RDHW1

2 B,K,F,7 PK151RDH02 PK201RDH02 PK251RDH02 PK321RDH02 PK401RDH02


4 B,7 PK151RDH04 PK201RDH04 PK251RDH04 PK321RDH04 PK401RDH04

4 K,F PK151RDHK5 PK201RDHK5 PK251RDHK5 PK321RDHK5 PK401RDHK5




8 B,F,K PK151RDH08 PK201RDH08 PK251RDH08 PK321RDH08 PK401RDH08

Seal ClassPiston Rod Diameter

0.625 1.000 1.375 1.750 2.000 2.500Class 1 RKRDH00061 RKRDH00101 RKRDH00131 RKRDH00171 RKRDH00201 RKRDH00251

Class 2 RKRDH00062 RKRDH00102 RKRDH00132 RKRDH00172 RKRDH00202 RKRDH00252


Class4 RKRDH00064 RKRDH00104 RKRDH00134 RKRDH00174 RKRDH00204 RKRDH00254


Class 8 N/A RKRDH00108 RKRDH00138 RKRDH00178 RKRDH00208 RKRDH00258

Class1(LowFriction) N/A RKRDHF0101 RKRDHF0131 RKRDHF0171 RKRDHF0201 RKRDHF0251

Class5(LowFriction) N/A RKRDHF0105 RKRDHF0135 RKRDHF0175 RKRDHF0205 RKRDHF0255

Class1(MetallicScrapper) RKRDHM0061 RKRDHM0101 RKRDHM0131 RKRDHM0171 RKRDHM0201 RKRDHM0251


Piston and Rod Seal Kits

Piston Seal Kits

Rod Seal Kits

Seal ClassPiston Rod Diameter

3.000 3.500 4.000 4.500 5.000 5.500Class 1 RKRDH00301 RKRDH00351 RKRDH00401 RKRDH00451 RKRDH00501 RKRDH00551






Class1(LowFriction) RKRDHF0301 RKRDHF0351 RKRDHF0401 RKRDHF0451 RKRDHF0501 RKRDHF0551

Class5(LowFriction) RKRDHF0305 RKRDHF0355 RKRDHF0405 RKRDHF0455 RKRDHF0505 RKRDHF0555



Seal Class

Piston Code

Bore Diameter

5.00 6.00 7.00 8.001 B,7 PK501RDH01 PK601RDH01 PK701RDH01 PK801RDH01

1 K,F PK501RDHK1 PK601RDHK1 PK701RDHK1 PK801RDHK1

1 W PK501RDHW1 PK601RDHW1 PK701RDHW1 PK801RDHW1

2 B,K,F,7 PK501RDH02 PK601RDH02 PK701RDH02 PK801RDH02


4 B,7 PK501RDH04 PK601RDH04 PK701RDH04 PK801RDH04

4 K,F PK501RDHK5 PK601RDHK5 PK701RDHK5 PK801RDHK5




8 B,F,K PK501RDH08 PK601RDH08 PK701RDH08 PK801RDH08

Heavy Duty Hydraulic Roundline CylindersCommon Modifications



31

C

Water Submersible Option

Optional PolyPak Inner and Outer Rod Seals resist internal and external pressure. Requiredfordepthsgreaterthan25feet.

Optional Dual End Seals resist external pressure. Required for depths greater than25feet.

Standard 17-4 Heat-Treated, Chrome-Plated, High Tensile Stainless Steel Piston Rod Material resists corrosion.

Several surface treatment options are available for protection against the operating environments.


Specifications:• SubmersionDepth–to15,000feet• NominalPressure–3,000psi• OperatingTemperature–-10°Fto+165°F• 17-4PHchromeplatedstainlesssteelpistonrod• Stainlesssteelnametag

Cylinder Seal Construction:• 0to25feetdepth–Standardrodsealandendseals• 25to5,000feetdepth – Subsearodsealpackagethatincludesa PolyPak oil seal and an outward-facing PolyPak wiper to seal against water intrusion. – SubseaendsealpackagewithIDoilsealand body-end o-ring to seal against water intrusion.• Over5,000feetdepth–consultfactoryfordetails

Standard Options for Water Submersible Cylinders:Material• ChromeplatedcylinderbodyID

Surface Treatments for Corrosion Protection• Electrolessnickelplatedexterior(head,capand

cylinder body)• Inorganiczincprimer(zincprimeronly–withoutbond

coating)• Inorganiczincprimerwithepoxyundercoatand

polyurethane or acrylic epoxy topcoat• Epoxyundercoatandtopcoat

Custom Options available for Special Order:• Allstainlesssteelconstruction




32

How to Order Water Submersible Option

How to order:1. Specify the complete cylinder model number.2.Putan“S”inthemodelnumbertoindicateaSpecialModification.3. Include the 3 digit “Submersible Code” (see below).4.Forcustomoptions,provideacompletedescriptionordrawingofyourrequirements.

Submersible Code Whenselectingthesubmersibleoption,anSmustbeplacedintheModelNumber.SelectSubmersibleCodevaluesfortherequiredSubmersionDepth,CylinderBody,andCorrosionProtection.SeetheexampleModelNumber below:

Example: 4.00BBRDHKTS14A24.000 S = Submersible Code 2P1(describesa4"borex24"strokeSeriesRDHcylinderforsubmersionupto5,000feet,withaplaincylinderbodyIDand inorganic zinc primer corrosion protection.)

Feature Code Specification For

Submersion Depth1 Conventional rod seal, rod wiper and end seal Depthsto25feet2 Submersible rod seal, rod wiper and end seal Depthsto5,000feet3 Other Specify depth / requirements

CylinderBodyP Plain cylinder body IDC Chrome plated cylinder body ID

Corrosion Protection

1 Inorganic zinc primerSplash and short term immersion service where equipment is top coated by the customer

3 Electroless nickel plated exterior

4 Inorganic zinc primer, epoxy undercoat, and polyurethane or acrylic epoxy topcoat. Splash and short term immersion service

6 Epoxy base and top coat. Longtermimmersionservice9 Other Specify requirements

Water Submersible Codes and Features SuppliedDepths to 5,000 feet1

Submersible Cylinder Feature

Water Submersible Code1

2P1 2P3 2P4 2P6 2C1 2C3 2C4 2C617-4PHstainlesssteelpistonrod X X X X X X X XStainless steel nametag X X X X X X X XSubmersible rod seal and wiper X X X X X X X XDual end seals X X X X X X X XChrome plated cylinder body ID X X X XElectroless nickel plated exterior X XInorganic zinc primer X XInorganic zinc primer with topcoats X XEpoxy base and topcoat X X

1Correspondingsubmersiblecodesfordepthsto25feetbeginwith1(e.g.1P1,1P3,etc.)andincludeallofthe featuresmarkedfor5,000feetdepthexcept Submersible Rod Seal, Rod Wiper and End Seals.





33

C

Hi Load Piston

The effective difference...Parker’s bronze filled PTFE ring design.n Virtuallyeliminatesleakagen High load capacityn High contamination tolerancen Longlifen Lowfriction

The revolutionaryParkerHiLoadpistonassembly was designed to increase and insure consistent quality performance of the piston seals and your equipment. It’s a major innovative refinement over typical cast iron piston rings and nitrile or fluorocarbon lipseals.TheHiLoadpistonassemblyovercomestheinherentproblems commonly associated with these conventional types of seals, such as scoring of the cylinder bore due to contamination, and it virtually eliminates leakage flow. It can also reduce or eliminate the need for stop tubing. It has much greater side load carrying capacity, and most importantly, even at pressures up to 3,000 psi, it has a longer wearing life than any seal that we have tested to date. TheHiLoadpistonassemblyiscomprisedofabronzefilledPTFEpistonseal(withanitrileenergizer)andaWearGard™ non-metallic wear ring to achieve dramatic efficiency.Reduced scoring. Low friction. TheWearGard™ non-metallic wear ring eliminates all metal-to-metal contact between the piston and cylinder body. Some scoring may occur even with the use of compatible materials such as cast iron or bronze for the piston and steel for the cylinder body. The combination of the high imbeddability factor and the wiping action of the wear ring prevents contamination from getting between the piston bearing and sealing surfaces; therefore, scoring is greatly reduced and cylinder life is extended. Other benefitsoftheHiLoadpistonareexcellentlubricityandminimum wear when using water base fluids, soluble oil &water,orbiodegradablefluids.Extensive controlled contamination tests in our labor- atoryhaveshowntheHiLoadpistontooperatemorethan 4 times longer than lip seals when high degrees of contamination are present.Note:BecausetheHiLoadpistonpreventsmetal-to-metal contact with the cylinder bore, steel pistons may be used.Higher side load carrying capacity. Under severe side load conditions arising from long stroke or pivot mounted cylinders, the characteristics of a non-metallic wear ring provide increased side load carrying capa-bility, a distinctive benefit. The non-metallic bearing can also absorb hydraulic shock and conform more to the piston and cylinder body. The action of deformation increases the area of contact, which in turn keeps the contact stresses from increasing and permits the HiLoadpistontohaveahighersideloadcarryingcapacity. This can often reduce or eliminate the need for stop tubing.

Comparative Piston Seal Friction

200C

AST

IRO

N R

ING

S

PISTON SEAL FRICTION2 IN. BORE

175

150

125

100

75

50

25

0 500 1000 1500 2000 2500 3000PRESSURE PSIG

FRIC

TIO

N L

BS

.

BRONZE-FILLED PTFE

LIPSEAL WITH BACK-UP

The Exclusive Parker Hi Load Piston

Virtually zero leakage.TheHiLoadpistonassemblyprovides virtually zero leakage with hydraulic and/or water base fluids due to the continuous bronze filled PTFEringwithahomogenousinnerringofNitrilerubber to apply seal preloading. The Nitrile energizer provide enough initial radial force to eliminate low pressure leakage. At higher pressure (above 2,000 psi) the seal is also pressurized underneath, and is therefore dynamically self-sealing.ThebronzefilledPTFEresistsextrusionintheclear-ance between the piston and bore much better than Nitrile, and, as a result, increases the life of a cylinder, significantly at higher pressures.WhenorderingtheHiLoadpistonoptionforSeriesRDHcylinders,specifyKinthePistonfieldofthe model code.

Optional Hi Load Piston




34

Low Friction Seals

nSmooth-runningoperation–reduces“stick/slip” or “chatter”

n BronzefilledPTFEsealsandWearGard™ wear rings for low friction, rapid break-in and long service life

n Appropriate for servo applicationsnInnovative seal geometry for maximum sealing efficiencyn WhenorderingSeriesRDHcylinders,placean“F” inthePistonfieldforLowFrictionSeals.

Low Friction Rod Seal Design A - DualbronzefilledPTFEstep-sealrodseals insure positive sealing and smooth operation at low or high pressures.

B - Elastomer expander for pressure compensation and low pressure effectiveness.

C -Durable,energizedbronzefilledPTFElipwiper keeps contaminants out.

D -WearGard™ wear ring for high load capacity, low friction and no metal-to-metal contact.

Available for all standard piston rod diameters larger than 0.625"

Low Friction Piston Seal Design A - WearGard™ wear ring for high load capacity, low friction and no metal-to-metal contact.

B - BronzefilledPTFEpistonsealinsuresmaximum sealing efficiency.

C - Elastomer expander for pressure compensation and low pressure effectiveness.

Available for all standard bore diameters.

Low Friction Seal Option

B

C A

B

C A

Seal FrictionSeal friction under a given set of working conditions is not easily calculated due to the multiplicity of variables involved. The following graph is offered as a guide for use in performance calculations, but for critical applications, measurements should be made under simulated or actual working conditions.

4

500 1000 1500 2000 2500 3000

Pressure (psi)

3

2

1

0

FrictionFactor (F)

(FL) Standard Seals

(FP) Low Friction Seals

D




35

C

Low Friction Seals

Calculation of Running FrictionThe seal friction attributable to the cylinder is calculated as the sum of the friction due to the individual sealing elements(wipersealfriction+rodsealfriction+pistonseal friction), using the following formulae:Option: Formula:Standardrodandpistonseals 12d+12FLd+24FLDLowfrictionrodandpistonseals 12d+30Fpd+6FpD Where: d = rod dia. (inch) D = bore dia. (inch) FL=frictionfactorforstandardseals(FL) Fp=frictionfactorforPTFElowfrictionseals(Fp)

Breakaway FrictionBreakawayfrictionmaybecalculatedbyapplyingthefollowing correction factors: Correctionfactors– Standardseals: FLx1.5 Lowfrictionseals: Fp x 1.0

Sample CalculationSeriesRDHCylinderwith3.25dia.boreand1.75dia.pistonrodwithlowfrictionsealsat1500psi.

Running Friction Calculation:Friction(lbs.force)≈ 12d+30Fpd+6FpDFriction(lbs.force)≈ 12(1.75)+30(1.3x1.75) +6(1.3x3.25)Friction(lbs.force)≈ 115

Breakaway Friction Calculation:Fp x 1.0 ≈Fp

Basedonzeropressure:Friction(lbs.force)≈ 12d+30Fpd+6FpDFriction(lbs.force)≈ 12(1.75)+30(.3x1.75) +6(.3x3.25)Friction(lbs.force)≈ 43

Specifications for Low Friction Options:Operating Pressure: 0 - 3000 psiOperatingTemperature:-10°Fto+165°F. Forhighertemperatures,consultfactory.FluidMedia:petroleum-basedhydraulicoils. Forotherfluids,consultfactory.




36

Series RDH Common Modifications

.107.005.000

To determine extra length of piston rod required to accommodate boot, calculate:BL=StrokexLF+1.13"BL+W+A=lengthofpistonrodto extend beyond the head face.Note:CheckallBootO.D’sagainst “E” dimension from catalog.

The following modifications can be supplied on most Series RDH cylinders for an additional charge.

Metallic Rod Wiper When specified, metallic rod wipers can be supplied instead of the standard urethane wiperseal. Recom-mended in applications where contaminants tend to cling to the extended piston rod and would damage the standard urethane wiperseal. Installation of metallic rod wiper does not affect cylinder dimensions.

Air Bleeds In most hydraulic circuits, cylinders are considered self-bleeding when cycled full stroke. If air bleeds are requiredandspecified,AirBleedPortsforventingaircan be provided at both ends of the cylinder body, or ontheheadorcap.Toorder,specify“BleedPort”andindicate the desired position on the cylinder.

Rod End BootsCylinders have a hardened bearing surface on the piston rod to resist external damage and are equipped with the high efficiency “wiperseal” to remove external dust and dirt. Exposed piston rods that are subjected to contaminants with air hardening properties, such as paint, should be protected. In such applications, the use of a collapsing cover should be considered. This is commonly referred to as a “rod boot”. Calculate the longer rod end required to accommodate the collapsed length of the boot from the following data.

LFODMM

.132.25.500

.132.25.625

.132.631.000

.133.00 1.380

.133.381.750

.133.752.000

.105.133.000

.105.633.500

.106.25 4.000

.107.505.500

.50 .63

ØMM

BL

OD

.134.382.500

Stroke AdjustersFortherequirementwhereadjustingthestrokeis specified. Several designs are available.

A “retracting stroke adjuster” must be ordered with an SforSpecialModificationinthemodelcode,andthelength of the adjustment must be specified.

“Infrequent-type” is defined by positioning the retract stroke in a couple of attempts at original machine set up. The “frequent-type” stroke adjuster is recommended for adjustments required after the equipment has been adjusted by the original machine manufacturer.

Metric Piston Rod Thread The table below lists the standard thread supplied when PistonRodThreadTypeMisspecifiedinthecylindermodelcodewithPistonRodEnds4,8and9.ForStyle7M,seepage15fordetails.

MM Rod

Ø (inches)

Thread Size AThread Length(inches)

Styles 4M & 9M

KK

Style 8M CC

0.625 M10x1.5 M12x1.5 0.751.000 M20x1.5 M22x1.5 1.131.375 M26x1.5 M30x2 1.631.750 M33x2 M39x2 2.002.000 M39x2 M45x2 2.252.500 M48x2 M56x2 3.003.000 M58x2 M68x2 3.503.500 M64x2 M76x2 3.504.000 M76x2 M95x2 4.004.500 M80x2 M110x2 4.505.000 M90x2 M110x2 5.005.500 M100x2 M130x2 5.50

Rectangular Head and Cap FlangesRectangular head flanges and cap flanges that match-mountNFPAStyleME5andME6areavailableasaspecialmodification.Enter“S”forSpecialModificationin the cylinder model code, request the desired flange in the item notes and consult the factory for a quote.

Welded Rod End Accessories Some standard and special rod end accessories can be welded to the piston rod. In the cylinder model code, specify"3"inthePistonRodThreadStylefield(forspecial rod end). Then describe the accessory in the item notes (or furnish a dimensioned sketch), signify that it is welded to the piston rod and consult the factory for a quote.

Additional common and custom modifications are available, see Custom Options and Modifications page or consult the factory.




37

C

ALS Switch

•Switchesandcylindercombinetoformacompact package•Body-mountedswitchesareeasilyadjustable

along cylinder stroke length•Lowprofileswitchesarelessproneto

mechanical damage

Durable polyurethane bi-directional seal –forpositive sealing with no by-pass and long life.

Cylinder Body –Standard carbon steel materialforALSSwitch.

WearGard™ wear ring – improves resistance to bearing loads and provides support for magnet.

Series RDH Cylinder – with magnetic piston

•Non-intrusivedesigneliminatesthepossibilityof oil leakage•Utilizesthestandardcarbonsteelcylinder

body

Switches Mounted on Series RDH Cylinders Add Value to Your Machine Design




38

ALS Switch Specifications

ALS Switch Wiring and Installation•Formagneticpistonsensingthroughsteel

tube material•4wireDCconnection•PNPandNPNversionscanbewiredN.O.

or N.C.

•TheALSSwitchisnotdesignedforusewithnon-ferrous tubes•CEapproved•ATEXapprovedversionavailable

Switch OperationThe switch detects a change in polarity of the magnetic field as a piston with magnet moves through the cylinder.

FormattingBeforetheswitchisusedforthefirsttime,thepistonwith magnet should be run in and out of the cylinder to format the cylinder tube. The switch will detect the polarity of the residual magnetic field created by the movement of the magnetic piston during formatting.

Field Direction with Magnetic PistonSingle rod end cylinders are assembled with the piston magnet’s North Pole facing the rod end. As the magnetic piston moves through the cylinder, it creates a stronger field opposite in polarity to the residual magnetism in the cylinder tube. As it moves under the switch, the change in polarity of the magnetic field in the cylinder tube is detected.

Switch ZoneSwitch actuation occurs as the piston enters a switching “zone”. The switching point is highly repeatable, in either direction, under conditions of constant piston speed and operating temperature.

Note:ALSSwitchesaredesignedtosensenearend of stroke positions (“stroke-to-go”) and stroke positions inbetweenthesetwopoints.Fortrueend-of-stroke positionsensing,usetheCLS-AorEPS-ALimitSwitchesfeaturedontheEPS-ASensors/CLS-ASwitches page.

The switching zone may be up to 21mm wide depending on tube wall thickness and piston speed.

LED IndicatorsTherearetwoLED’s(yellowandred)toindicatethatthe piston is inside or outside the switching zone. The sequenceoftheLED’sisdeterminedbytheorientationof the north pole of the magnet system (rod end side of single rod end cylinders) to the connector.

WhentheALSSwitchconnectorfacestherodsideofsinglerodendcylinderstheredLEDturnsONwhenthepistoniswithintheswitchingzone.TheyellowLEDis ON otherwise.

WhentheALSSwitchconnectorfacesthecapsideof singlerodendcylinderstheyellowLEDturnsONwhen thepistoniswithintheswitchingzone.TheredLEDis ON otherwise.

PerformanceALSSwitcheshavebeendesignedtooperateatamaximumpistonspeedof0.5m/s,andamaximumcylinderoperatingtemperatureof85°C.

YELLOWLED

REDLED

Black

A2

White

Blue

Brown

N.C. Load

N.O.

(+)

Load

(-)

ALS-P

64.050.0

M12x1.0 METRIC THREAD

7.2

10.5

TARGETAREA

18.021.0

SpecificationsSwitching Output: PNP or NPN

Hysteresis1: 5mmRepeatability1: 0.5mmLoad Current: 100mA

Leakage Current: < 10µAVoltage Drop: <1.5VDC

Short Circuit and Overload Protection: Yes

Reverse Polarity Protection: Yes

Supply Voltage: 10-30VDCLED(s): Yes (2)

Current Consumption: < 30 mAOperating

Temperature Range:-25°Cto+85°C (-13°Fto+185°F)

Housing Material: BlackPolyamide(PA)Enclosure Rating: IP67

1Hysteresis and repeatability based on measurements withacylinderouterdiameterof46mm,wallthickness of3mmandpistonspeedof0.5m/s.

ALSSwitchoutputstatesmaybeinfluencedbyanexternal magnetic field. Care must be taken to avoid external magnetic field exposure.




39

C

ALS Switch Wiring Connection

ALS Switch – Wiring Connection12mm Connector

34

21

PNP

N.O. LOAD

1 BROWN

4 BLACK

2 WHITE

3 BLUE

( )+

( )-LOADN.C.

NPN

N.O.N.C.

LOADLOAD

1 BROWN

4 BLACK

2 WHITE

3 BLUE

( )+

( )-

ALS Switch Wiring and InstallationBecausetheALSSwitchdetectschangeinpolarity as the magnet moves through the cylinder, wiring connections are dependent on switch mounting orientation to the magnet’s North Pole. The two possible orientations are:

A–connectorfacingtowardtherodend (rodend1ifK-type)

B–connectorfacingtowardthecapend (rodend2ifK-type)

ConnectionstoPin1(+VDC)andPin3(-VDC)arethesameforeitherswitchorientation.But,asoutlinedin the table and wiring schematic diagrams below, the normaloutputstateofPins2&4flipbetweenmount-ingorientationsA&B.Notethattosensenearthefullyretracted position of the cylinder the cap end switch must be mounted in orientation A, and to sense near the fully extended position of the cylinder the rod end switch must bemountedinorientationB.

General view of switches as installed:

Example:AnapplicationrequiresthatALSSwitchessense two positions of the cylinder with normally closed logicatbothends.Howwouldtheswitchesbewired?

Answer: The two switches would not be installed or wired the same way. The cap end switch would be installedinorientationAwithPin1(+VDC),Pin2(Load),Pin3(-VDC),Pin4(notused).TherodendswitchwouldbeinstalledinorientationBwithPin1(+VDC),Pin2(notused),Pin3(-VDC),Pin4(Load).

Switch Mounting

Orientation

Connector Facing Toward

LED indicator (on/off) when magnet is:

Pin Wire Function

Single Rod Cylinder

Double Rod Cylinder

Out of Switch Zone In Switch ZoneRed Yellow Red Yellow

A Rod End Rod End #1 off on on off

1 Brown +VDC2 White N.C.3 Blue -VDC4 Black N.O.

B Cap End Rod End #2 on off off on

1 Brown +VDC2 White N.O.3 Blue -VDC4 Black N.C.

LED Function and Pin Wiring

Switch Orientation A Switch Orientation A

Switch Orientation B Switch Orientation B

N.O. LOAD

1 BROWN

4 BLACK

2 WHITE

3 BLUE

( )+

( )-LOADN.C.

N.O.N.C.

LOADLOAD

1 BROWN

4 BLACK

2 WHITE

3 BLUE

( )+

( )-

B

B




40

ALS Switch Part Numbers

ALS Switch and Accessory Part NumbersAllswitcheshavea4-pinmaleM12x1threadedconnector.

Minimum Net Stroke for ALS SwitchBore

Ø Stroke

1.50 3.00

2.00 3.00

2.50 2.88

3.25 2.75

4.00 2.63

5.00 2.38

6.00 2.19

12mm Cordset for ALS Switches12mmCordsetwithFemaleQuickConnect

M12 Straight ConnectorCable Length Part Number5meters 9126487205

2 meters 9126487202

M12 Right Angle ConnectorCable Length Part Number5meters 9126487305

2 meters 9126487302

Cordset SpecificationsConnector ................Polyvinylchloride(PVC)body

material,PVCcontactcarrier,spacingtoVDE0110GroupC,(250VAC/300VDC)

Contacts ..................GoldPlatedCopperTin(CuSn),stamped from stock.

CouplingMethod ..... Threaded nut: Chrome plated brass.

Cord Construction ...PVCnon-wicking,non-hygroscopic, 250VAC/300VDC.Cableendisstripped.

Conductors ..............ExtrahighflexstrandingwithPVCinsulation

Temperature ............ -13°Fto158°F(-25°Cto70°C)Protection ................NEMA1,3,4,6PandIEC1P67CableLength ...........6.56ft(2m)or16.4ft(5m)

A female connector is available for all switches with the male 12mm quick connect option. The cordsets are available with a right angle or straight connector. Cordset part numbers are listed above.

Straight Connector

Right Angle Connector

42

Ø14.5

CABLE LENGTH (m)(SEE TABLE)

1.5

PIN 4 /BLK

PIN 2 / WHTPIN 3 / BLU

M12 X 1CABLE MINIMUM BENDRADIUS: 100mmPIN 1 / BRN

CABLE MINIMUMBEND RADIUS:

100mm

CABLE LENGTH(SEE TABLE)

M12 X 1

1.526.5

PIN 2 / WHT

PIN 3 / BLU

PIN 4 / BLKPIN 1 / BRN38.3

Ø14.5

BodymountingbandforALSswitchesmustbeorderedseparately.

Note:Specifypistoncode‘7’incylindermodelnumberwhenusingALSSwitches.

Switch Part Number

PNP NPN

0944520000 0942230000

Body Mounting Band Part Number

Bore Ø

Part Number

1.50 0853990005

2.00 0853990005

2.50 010151006M

3.25 010151007M

4.00 010151008M

5.00 010151010M

6.00 010151011M




41

C

EPS-A Sensors / CLS-A Switches

CLS-A Threaded Style End-Of-Stroke Limit SwitchesNon-contacting, magnetically-actuating

As shown in the illustrations below, these switches are magnetically operated. Dual magnets provide a dependable “snap action“ for positive position sensing.

In the “Unoperated” position, the magnet assembly is attracted in the opposite direction of the arrow, causing a finely ground stainless steel connecting rod to hold the contacts open.

SensingArea

SensingDistance

Magnet Ass’y Switch Case

N/O

N/CCom.

Unoperated

N FerrousActuator

DifferentialConnecting Rod

N/O

N/CCom.

Operated

N

Operating Principle

See the specification table on the next page for additional details.

In the “Operated” position a ferrous part (piston or piston spacer) enters the sensing area and attracts the magnet assembly which causes the rod to draw the contacts together.

Threaded switches can be height-adjusted for small changes to end-of-stroke position sensing.

Note: Cylinders that include CLS-A Switches may be longer than standard cylinders. Consult Switch Dimension tables for exact lengths.

EPS-A Threaded Style End-Of-Stroke Inductive Proximity Sensor

•Shoulderedone-piecestainlesssteelbodyforpositiveinstallation and easy replacement•PNP(sourcing)output•NormallyOpenfunction•10-30VDC

•Minorvoltagedropandleakagecurrent•CE,C-UL-USApproved•IP68rating•4-pin12mmconnector(standard)•Cableandshortcable/connectoroptions

Non-contacting, end-of-stroke position sensor

Sensing gap: .030"to.060"Trip point: Factorysetwithpiston bottomed out.Release point:Approx.0.250"of piston travel.Minimum net strokeis0.500"for1.50"and2.00"boresand0.750"forlargerbores.

Note: Cylinders that include EPS-A Switches may be longer than standard cylinders. Consult Switch dimension tables for exact lengths.




42

EPS-A Sensor & CLS-A Limit Switch Specifications

Switch Type: Inductive Proximity Non-contacting, magnetically actuating

Style: EPS-A CLS-A

Code Designator: C G

Description: "GeneralPurpose,3wire, DCSensor"

Forapplicationswherethecustomerneeds NO or NC contacts, zero

leakage, zero voltage drop, higher or lower load current than EPS style.

Threaded style permits small adjustability of make/break location.

Supply Voltage: 10to30VDC 24to240VAC/DC

Load Current, min.: NA

Load Current, max.: 200 mA4AMPS@120VAC

3AMPS@24VDC

Leakage Current: 10 µA None

Voltage Drop: ≤2.0V None

Operating Temperature: -13°Fto+194°F -40°Fto+221°F

Part Number: 0961640M120961710000-1.50"Bore

0961680000-2.00"-8.00"Bores

Connection: M124-pinconnector 3-pin micro connector

Enclosure Rating: Enclosure–IP68 Enclosure–IP68

LED Indication: No No

Short Circuit Protection: Yes No

RFI/Weld Field Immune: No Yes

Output: PNPSPDT (Single Pole Double Throw), Normally Open/Normally Closed,

FormC

Approvals/Marks: CE ULListedGeneralPurpose

Make/Break Location: 0.25"fromendofstroketypical. Toleranceis+0/-0.13"

0.25"fromendofstroke,typical. Toleranceis+0/-.13"

Wiring Instructions:

Options: (Consult factory)

5mcable

½"conduithub,cable,flyinglead and other connector types

Hightemperatureversion(to+400°F)

ATEX, CSA, intrinsically-safe, explosion-proof, non-incendive,

DPDT and Subsea versions

EPS-A Sensor / CLS-A Switch Specifications

bn

bk

bu

1

4

3

+

DC

–

2

4

13 12

3Pin 1 ComPin 2 N/CPin 3 N/O




43

C

How to Order EPS & CLS Limit Switches

EPS-A&CLS-Alimitswitchesmaybeorderedasfollows:

1) Complete the basic cylinder model number.

2) Place an “S” in the model number for Special Modification.

3)MountingstylesDD,JandHshouldbeusedwithcaution because of possible mounting interferences.

4)Specialmodificationstocylindersotherthanswitches must be described in the item notes.

Head EndG 1 3 GG

Specify:“C” = EPS-A“G”=CLS-A

“T” = Prepared forCLS-AThreaded

Switch“X” = Special

installed switch

(Specify)

Port Location

See Figure1.

Switch Location

See Figure1.

Actuation Point

GG=End of Stroke.

Cap End4 2 GG

Port Location

See Figure1.

Switch Location

See Figure1.

Actuation Point

GG=End of Stroke.

Note: All specified switch and port locations are as seen from rod end of cylinder.

5)LimitSwitchCode–Specifyletterprefix“C”forEPS-Aor“G”forCLS-A,thenfillinthefourblanksspecifying port location, switch location and actuation point for both head and cap. If only one switch is used, place “XXXX” in the unused blanks.

Example=G13GG-XXXXdenotesaswitchonthehead end only.

Example=XXXX-G42GGdenotesaswitchonthecapend only.

Head (Rod) End Head Cap

Limit Switch Code

Figure 1

1

2

3

4




44

Dimensions – Cylinders with Limit Switches

SeriesRDHcylinderswithLimitSwitchesrequireadditional length for the piston collar(s) required to activate the switch. The table below and those on following pages show dimensions that are changed when switches are

specified. Note that dimension changes are specific to whether switches are specified on both ends, switch on cap end only or switch on head end only.

Switch on Both Ends

Bore Ø

Rod No.

MM Rod

Ø

All Mountings All Mountings Except Styles J/JP

Styles T & DD

Styles B & BB

Style SB Style SBM

ER HS EN Add Stroke Add Stroke

Add Stroke Add Stroke Add Stroke

CLS-A EPS-A CLS-A EPS-A LB P ZJ XC ZC XC ZC XC ZC

1.501 (std) 0.625 0.83 4.49 2.66 1.63 1.63 4.19 1.82 4.75 5.50 6.00 5.50 6.25 5.73 6.87

2 1.000 0.83 4.49 2.66 2.01 2.01 4.56 1.82 5.25 6.00 6.50 6.00 6.75 6.23 7.38

2.001 (std) 1.000 1.12 4.25 2.91 2.31 2.20 5.69 2.81 6.38 7.63 8.38 7.63 8.63 7.60 8.89

2 1.375 1.12 4.25 2.91 2.31 2.20 5.69 2.81 6.50 7.75 8.50 7.75 8.75 7.72 9.02

2.501 (std) 1.000 1.31 4.47 3.13 2.56 2.45 6.13 2.75 6.81 8.06 8.81 8.06 9.06 8.31 9.88

2 1.750 1.31 4.47 3.13 2.56 2.45 6.13 2.75 7.06 8.31 9.06 8.31 9.31 8.56 10.133 1.375 1.31 4.47 3.13 2.56 2.45 6.13 2.75 6.94 8.19 8.94 8.19 9.19 8.43 10.01

3.251 (std) 1.375 1.68 4.84 3.51 2.81 2.70 6.88 2.94 7.69 9.19 10.19 9.19 10.44 9.58 11.55

2 2.000 1.68 4.84 3.51 2.81 2.70 6.88 2.94 7.88 9.38 10.38 9.38 10.63 9.76 11.733 1.750 1.68 4.84 3.51 2.81 2.70 6.88 2.94 7.81 9.31 10.31 9.31 10.56 9.70 11.67

4.001 (std) 1.750 1.44 5.15 3.82 3.06 2.95 7.25 3.25 8.19 10.31 11.69 10.31 12.19 10.47 12.91

2 2.500 1.44 5.15 3.82 3.06 2.95 7.25 3.25 8.31 10.44 11.81 10.44 12.31 10.59 13.033 2.000 1.44 5.15 3.82 3.06 2.95 7.25 3.25 8.25 10.37 11.75 10.37 12.25 10.53 12.97

5.00

1 (std) 2.000 1.79 5.59 4.26 3.31 3.20 7.87 3.31 8.87 11.12 12.87 11.12 13.62 11.70 14.852 3.500 1.79 5.59 4.26 3.31 3.20 7.87 3.31 8.93 11.18 12.93 11.18 13.68 11.76 14.913 2.500 1.79 5.59 4.26 3.31 3.20 7.87 3.31 8.93 11.18 12.93 11.18 13.68 11.76 14.914 3.000 1.79 5.59 4.26 3.31 3.20 7.87 3.31 8.93 11.18 12.93 11.18 13.68 11.76 14.91

6.00

1 (std) 2.500 2.36 6.09 4.76 3.19 3.14 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.992 4.000 2.36 6.09 4.76 3.19 3.14 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.993 3.000 2.36 6.09 4.76 3.19 3.14 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.994 3.500 2.36 6.09 4.76 3.19 3.14 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.99

7.00

1 (std) 3.000 2.67 6.59 5.26 3.20 3.08 9.00 3.25 10.06 13.06 15.56

N/A

14.63 18.572 5.000 2.67 6.59 5.26 3.20 3.08 9.00 3.25 10.19 13.19 15.69 14.75 18.693 3.500 2.67 6.59 5.26 3.20 3.08 9.00 3.25 10.06 13.06 15.56 14.63 18.574 4.000 2.67 6.59 5.26 3.20 3.08 9.00 3.25 10.06 13.06 15.56 14.63 18.575 4.500 2.67 6.59 5.26 3.20 3.08 9.00 3.25 10.19 13.19 15.69 14.75 18.69

8.00

1 (std) 3.500 2.96 7.09 5.76 3.41 3.29 9.50 3.25 10.56 13.81 16.56 15.12 19.852 5.500 2.96 7.09 5.76 3.41 3.29 9.50 3.25 10.68 13.93 16.68 15.25 19.973 4.000 2.96 7.09 5.76 3.41 3.29 9.50 3.25 10.56 13.81 16.56 15.12 19.854 4.500 2.96 7.09 5.76 3.41 3.29 9.50 3.25 10.68 13.93 16.68 15.25 19.975 5.000 2.96 7.09 5.76 3.41 3.29 9.50 3.25 10.68 13.93 16.68 15.25 19.97

Styles T & DD

Styles SB & SBM

Styles B & BBLB + STROKE

ZJ + STROKE

HS

EREN

HS

P + STROKELB + STROKE


HSHS

EREN

P + STROKE

LB + STROKE


HSHS

EREN

P + STROKE




45

C


Switch on Both Ends

Bore Ø

Rod No.

MM Rod

Ø

All Mountings Except Styles J/JP

Styles J/JP Style H Style TT

EN Add Stroke

EJ ER YF Add Stroke EH Add Stroke ER Add Stroke

CLS-A EPS-A P CLS-A EPS-A LG PJ ZG LH XF ZF LB XC ZC

1.50 1 (std) 0.625 1.63 1.63 1.82 2.01 2.01 0.83 2.75 4.56 1.82 5.37 1.08 4.06 4.62 5.00 0.83 4.19 5.37 6.002 1.000 2.01 2.01 1.82 2.01 2.01 0.83 3.25 4.56 1.82 5.88 1.08 4.44 5.13 5.50 0.83 4.56 5.88 6.50

2.00 1 (std) 1.000 2.31 2.20 2.81 2.44 2.33 1.12 3.26 5.81 2.81 6.75 1.43 5.56 6.25 6.69 1.12 5.69 7.00 7.632 1.375 2.31 2.20 2.81 2.44 2.33 1.12 3.38 5.81 2.81 6.87 1.43 5.56 6.37 6.81 1.12 5.69 7.12 7.75

2.501 (std) 1.000 2.56 2.45 2.75 2.69 2.58 1.31 3.44 6.25 2.75 7.19 1.68 6.00 6.69 7.19 1.31 6.13 7.56 8.31

2 1.750 2.56 2.45 2.75 2.69 2.58 1.31 3.69 6.25 2.75 7.44 1.68 6.00 6.94 7.44 1.31 6.13 7.81 8.563 1.375 2.56 2.45 2.75 2.69 2.58 1.31 3.56 6.25 2.75 7.31 1.68 6.00 6.81 7.31 1.31 6.13 7.69 8.44

3.251 (std) 1.375 2.81 2.70 2.94 2.94 2.83 1.68 3.81 7.00 2.94 8.06 2.18 6.75 7.56 8.19 1.68 6.88 8.62 9.56

2 2.000 2.81 2.70 2.94 2.94 2.83 1.68 4.00 7.00 2.94 8.25 2.18 6.75 7.75 8.38 1.68 6.88 8.81 9.753 1.750 2.81 2.70 2.94 2.94 2.83 1.68 3.94 7.00 2.94 8.19 2.18 6.75 7.69 8.31 1.68 6.88 8.75 9.69

4.001 (std) 1.750 3.06 2.95 3.25 3.06 2.95 1.44 4.15 7.25 3.25 8.44 2.07 7.12 8.06 8.81 1.44 7.25 9.19 10.19

2 2.500 3.06 2.95 3.25 3.06 2.95 1.44 4.27 7.25 3.25 8.56 2.07 7.12 8.19 8.94 1.44 7.25 9.31 10.313 2.000 3.06 2.95 3.25 3.06 2.95 1.44 4.21 7.25 3.25 8.50 2.07 7.12 8.12 8.87 1.44 7.25 9.25 10.25

5.00

1 (std) 2.000 3.31 3.20 3.31 3.25 3.14 1.79 4.45 7.80 3.31 9.12 2.54 7.74 8.74 9.62 1.79 7.87 10.24 11.622 3.500 3.31 3.20 3.31 3.25 3.14 1.79 4.51 7.80 3.31 9.18 2.54 7.74 8.80 9.68 1.79 7.87 10.3011.683 2.500 3.31 3.20 3.31 3.25 3.14 1.79 4.51 7.80 3.31 9.18 2.54 7.74 8.80 9.68 1.79 7.87 10.3011.684 3.000 3.31 3.20 3.31 3.25 3.14 1.79 4.51 7.80 3.31 9.18 2.54 7.74 8.80 9.68 1.79 7.87 10.3011.68

6.00

1 (std) 2.500 3.19 3.14 3.00 3.56 3.51 2.36 4.99 8.75 3.00 10.18 3.24 8.25 9.31 10.31 2.36 8.37 10.9312.432 4.000 3.19 3.14 3.00 3.56 3.51 2.36 4.99 8.75 3.00 10.18 3.24 8.25 9.31 10.31 2.36 8.37 10.9312.433 3.000 3.19 3.14 3.00 3.56 3.51 2.36 4.99 8.75 3.00 10.18 3.24 8.25 9.31 10.31 2.36 8.37 10.9312.434 3.500 3.19 3.14 3.00 3.56 3.51 2.36 4.99 8.75 3.00 10.18 3.24 8.25 9.31 10.31 2.36 8.37 10.9312.43

7.00

1 (std) 3.000 3.20 3.08 3.25 3.82 3.70 2.67 5.25 9.63 3.25 11.06 3.55 8.88 9.94 10.94 2.67 9.00 11.9413.812 5.000 3.20 3.08 3.25 3.82 3.70 2.67 5.38 9.63 3.25 11.19 3.55 8.88 10.0611.06 2.67 9.00 12.0613.943 3.500 3.20 3.08 3.25 3.82 3.70 2.67 5.25 9.63 3.25 11.06 3.55 8.88 9.94 10.94 2.67 9.00 11.9413.814 4.000 3.20 3.08 3.25 3.82 3.70 2.67 5.25 9.63 3.25 11.06 3.55 8.88 9.94 10.94 2.67 9.00 11.9413.815 4.500 3.20 3.08 3.25 3.82 3.70 2.67 5.38 9.63 3.25 11.19 3.55 8.88 10.0611.06 2.67 9.00 12.0613.94

8.00

1 (std) 3.500 3.41 3.29 3.25 3.91 3.79 2.96 5.44 10.00 3.25 11.56 3.96 9.37 10.4311.56 2.96 9.50 12.5614.562 5.500 3.41 3.29 3.25 3.91 3.79 2.96 5.56 10.00 3.25 11.68 3.96 9.37 10.5611.68 2.96 9.50 12.6814.683 4.000 3.41 3.29 3.25 3.91 3.79 2.96 5.44 10.00 3.25 11.56 3.96 9.37 10.4311.56 2.96 9.50 12.5614.564 4.500 3.41 3.29 3.25 3.91 3.79 2.96 5.56 10.00 3.25 11.68 3.96 9.37 10.5611.68 2.96 9.50 12.6814.685 5.000 3.41 3.29 3.25 3.91 3.79 2.96 5.56 10.00 3.25 11.68 3.96 9.37 10.5611.68 2.96 9.50 12.6814.68

1SeeportandswitchpositionnoteonmountingStylesJ/JP&Hpages.2 See previous page for HS dimensions.

Styles J/JP1

Style TT

Style H1

LG + STROKEZG + STROKE

HS2

ER

YF

EJ

HS2

PJ + STROKE

EN EH

HS2

P + STROKE

HS2

LH + STROKEXF + STROKE

ZF + STROKE

EN

HS2 HS2

ER

ZC + STROKEXC + STROKELB + STROKE

P + STROKE




46


Switch on Head End

Bore Ø

Rod No.

MM Rod

Ø

All Mountings All Mountings Except Styles J/JP

Styles T & DD

Styles B & BB

Style SB Style SBM

HS EN Add Stroke Add Stroke


CLS-A EPS-A CLS-A EPS-A LB P ZJ XC ZC XC ZC XC ZC

1.501 (std) 0.625 4.49 2.66 1.63 1.63 4.06 1.69 4.62 5.37 5.87 5.37 6.12 5.61 6.75

2 1.000 4.49 2.66 2.01 2.01 4.44 1.69 5.13 5.88 6.38 5.88 6.63 6.11 7.25

2.001 (std) 1.000 4.25 2.91 2.31 2.20 5.56 2.68 6.25 7.50 8.25 7.50 8.50 7.47 8.77

2 1.375 4.25 2.91 2.31 2.20 5.56 2.68 6.37 7.62 8.37 7.62 8.62 7.59 8.89

2.501 (std) 1.000 4.47 3.13 2.56 2.45 6.00 2.63 6.69 7.94 8.69 7.94 8.94 8.18 9.76

2 1.750 4.47 3.13 2.56 2.45 6.00 2.63 6.94 8.19 8.94 8.19 9.19 8.43 10.013 1.375 4.47 3.13 2.56 2.45 6.00 2.63 6.81 8.06 8.81 8.06 9.06 8.31 9.88

3.251 (std) 1.375 4.84 3.51 2.81 2.70 6.75 2.81 7.56 9.06 10.06 9.06 10.31 9.45 11.42

2 2.000 4.84 3.51 2.81 2.70 6.75 2.81 7.75 9.25 10.25 9.25 10.50 9.64 11.613 1.750 4.84 3.51 2.81 2.70 6.75 2.81 7.69 9.19 10.19 9.19 10.44 9.58 11.55

4.001 (std) 1.750 5.15 3.82 3.06 2.95 7.25 3.25 8.19 10.31 11.69 10.31 12.19 10.47 12.91

2 2.500 5.15 3.82 3.06 2.95 7.25 3.25 8.31 10.44 11.81 10.44 12.31 10.59 13.033 2.000 5.15 3.82 3.06 2.95 7.25 3.25 8.25 10.37 11.75 10.37 12.25 10.53 12.97

5.00

1 (std) 2.000 5.59 4.26 3.31 3.20 7.87 3.31 8.87 11.12 12.87 11.12 13.62 11.70 14.852 3.500 5.59 4.26 3.31 3.20 7.87 3.31 8.93 11.18 12.93 11.18 13.68 11.76 14.913 2.500 5.59 4.26 3.31 3.20 7.87 3.31 8.93 11.18 12.93 11.18 13.68 11.76 14.914 3.000 5.59 4.26 3.31 3.20 7.87 3.31 8.93 11.18 12.93 11.18 13.68 11.76 14.91

6.00

1 (std) 2.500 6.09 4.76 3.19 3.14 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.992 4.000 6.09 4.76 3.19 3.14 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.993 3.000 6.09 4.76 3.19 3.14 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.994 3.500 6.09 4.76 3.19 3.14 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.99

7.00

1 (std) 3.000 6.59 5.26 3.20 3.08 9.00 3.25 10.06 13.06 15.56

N/A

14.63 18.572 5.000 6.59 5.26 3.20 3.08 9.00 3.25 10.19 13.19 15.69 14.75 18.693 3.500 6.59 5.25 3.20 3.08 9.00 3.25 10.06 13.06 15.56 14.63 18.574 4.000 6.59 5.26 3.20 3.08 9.00 3.25 10.06 13.06 15.56 14.63 18.575 4.500 6.59 5.26 3.20 3.08 9.00 3.25 10.19 13.19 15.69 14.75 18.69

8.00

1 (std) 3.500 7.09 5.76 3.41 3.29 9.50 3.25 10.56 13.81 16.56 15.12 19.852 5.500 7.09 5.76 3.41 3.29 9.50 3.25 10.68 13.93 16.68 15.25 19.973 4.000 7.09 5.76 3.41 3.29 9.50 3.25 10.56 13.81 16.56 15.12 19.854 4.500 7.09 5.76 3.41 3.29 9.50 3.25 10.68 13.93 16.68 15.25 19.975 5.000 7.09 5.76 3.41 3.29 9.50 3.25 10.68 13.93 16.68 15.25 19.97

Styles T & DD

Styles SB & SBM

Styles B & BB

LB + STROKEZJ + STROKE

HS

EN

P + STROKELB + STROKE


HS

EN

P + STROKE

LB + STROKE


HS

EN

P + STROKE




47

C


Switch on Head End

1 SeeportandswitchpositionnoteonmountingStylesJ/JP&Hpages.2 See previous page for HS dimensions.

Bore Ø

Rod No.

MM Rod

Ø

All Mountings Except Styles J/JP

Styles J/JP Style H Style TT

EN Add Stroke

EJ YF Add Stroke Add Stroke Add Stroke

CLS-A EPS-A P CLS-A EPS-A LG PJ ZG LH XF ZF LB XC ZC

1.501 (std) 0.625 1.63 1.63 1.69 2.01 2.01 2.75 4.44 1.69 5.25 3.94 4.50 4.87 4.06 5.25 5.87

2 1.000 2.01 2.01 1.69 2.01 2.01 3.25 4.44 1.69 5.75 4.31 5.00 5.38 4.44 5.75 6.38

2.001 (std) 1.000 2.31 2.20 2.68 2.44 2.33 3.26 5.69 2.68 6.63 5.44 6.13 6.56 5.56 6.88 7.50

2 1.375 2.31 2.20 2.68 2.44 2.33 3.38 5.69 2.68 6.75 5.44 6.25 6.69 5.56 7.00 7.62

2.501 (std) 1.000 2.56 2.45 2.63 2.69 2.58 3.44 6.13 2.63 7.06 5.88 6.56 7.06 6.00 7.44 8.19

2 1.750 2.56 2.45 2.63 2.69 2.58 3.69 6.13 2.63 7.31 5.88 6.81 7.31 6.00 7.69 8.443 1.375 2.56 2.45 2.63 2.69 2.58 3.56 6.13 2.63 7.19 5.88 6.69 7.19 6.00 7.56 8.31

3.251 (std) 1.375 2.81 2.70 2.81 2.94 2.83 3.81 6.88 2.81 7.94 6.63 7.44 8.06 6.75 8.50 9.44

2 2.000 2.81 2.70 2.81 2.94 2.83 4.00 6.88 2.81 8.13 6.63 7.63 8.25 6.75 8.69 9.633 1.750 2.81 2.70 2.81 2.94 2.83 3.94 6.88 2.81 8.06 6.63 7.56 8.19 6.75 8.63 9.56

4.001 (std) 1.750 3.06 2.95 3.25 3.06 2.95 4.15 7.25 3.25 8.44 7.12 8.06 8.81 7.25 9.19 10.19

2 2.500 3.06 2.95 3.25 3.06 2.95 4.27 7.25 3.25 8.56 7.12 8.19 8.94 7.25 9.31 10.313 2.000 3.06 2.95 3.25 3.06 2.95 4.21 7.25 3.25 8.50 7.12 8.12 8.87 7.25 9.25 10.25

5.00

1 (std) 2.000 3.31 3.20 3.31 3.25 3.14 4.45 7.80 3.31 9.12 7.74 8.74 9.62 7.87 10.24 11.622 3.500 3.31 3.20 3.31 3.25 3.14 4.51 7.80 3.31 9.18 7.74 8.80 9.68 7.87 10.30 11.683 2.500 3.31 3.20 3.31 3.25 3.14 4.51 7.80 3.31 9.18 7.74 8.80 9.68 7.87 10.30 11.684 3.000 3.31 3.20 3.31 3.25 3.14 4.51 7.80 3.31 9.18 7.74 8.80 9.68 7.87 10.30 11.68

6.00

1 (std) 2.500 3.19 3.14 3.00 3.56 3.51 4.99 8.75 3.00 10.18 8.25 9.31 10.31 8.37 10.93 12.432 4.000 3.19 3.14 3.00 3.56 3.51 4.99 8.75 3.00 10.18 8.25 9.31 10.31 8.37 10.93 12.433 3.000 3.19 3.14 3.00 3.56 3.51 4.99 8.75 3.00 10.18 8.25 9.31 10.31 8.37 10.93 12.434 3.500 3.19 3.14 3.00 3.56 3.51 4.99 8.75 3.00 10.18 8.25 9.31 10.31 8.37 10.93 12.43

7.00

1 (std) 3.000 3.20 3.08 3.25 3.82 3.70 5.25 9.63 3.25 11.06 8.88 9.94 10.94 9.00 11.94 13.812 5.000 3.20 3.08 3.25 3.82 3.70 5.38 9.63 3.25 11.19 8.88 10.06 11.06 9.00 12.06 13.943 3.500 3.20 3.08 3.25 3.82 3.70 5.25 9.63 3.25 11.06 8.88 9.94 10.94 9.00 11.94 13.814 4.000 3.20 3.08 3.25 3.82 3.70 5.25 9.63 3.25 11.06 8.88 9.94 10.94 9.00 11.94 13.815 4.500 3.20 3.08 3.25 3.82 3.70 5.38 9.63 3.25 11.19 8.88 10.06 11.06 9.00 12.06 13.94

8.00

1 (std) 3.500 3.41 3.29 3.25 3.91 3.79 5.44 10.00 3.25 11.56 9.37 10.43 11.56 9.50 12.56 14.562 5.500 3.41 3.29 3.25 3.91 3.79 5.56 10.00 3.25 11.68 9.37 10.56 11.68 9.50 12.68 14.683 4.000 3.41 3.29 3.25 3.91 3.79 5.44 10.00 3.25 11.56 9.37 10.43 11.56 9.50 12.56 14.564 4.500 3.41 3.29 3.25 3.91 3.79 5.56 10.00 3.25 11.68 9.37 10.56 11.68 9.50 12.68 14.685 5.000 3.41 3.29 3.25 3.91 3.79 5.56 10.00 3.25 11.68 9.37 10.56 11.68 9.50 12.68 14.68

Styles J/JP1

Style TT

Style H1


HS2

EJ

YF PJ + STROKEXF + STROKE

LH + STROKE

ZF + STROKE

HS2

EN

P + STROKE

LB + STROKE


HS2

EN

P + STROKE




48


Switch on Cap End

Bore Ø

Rod No.

MM Rod

Ø

All Mountings Except Styles J/JP or H

Styles T & DD

Styles B & BB

Style SB Style SBM

ER HS Add Stroke Add Stroke


CLS-A EPS-A LB P ZJ XC ZC XC ZC XC ZC

1.501 (std) 0.625 0.83 4.49 2.66 3.69 1.32 4.25 5.00 5.50 5.00 5.75 5.23 6.37

2 1.000 0.83 4.49 2.66 4.06 1.32 4.75 5.50 6.00 5.50 6.25 5.73 6.88

2.001 (std) 1.000 1.12 4.25 2.91 4.94 2.06 5.63 6.88 7.63 6.88 7.88 6.85 8.14

2 1.375 1.12 4.25 2.91 4.94 2.06 5.75 7.00 7.75 7.00 8.00 6.97 8.27

2.501 (std) 1.000 1.31 4.47 3.13 5.38 2.00 6.06 7.31 8.06 7.31 8.31 7.56 9.13

2 1.750 1.31 4.47 3.13 5.38 2.00 6.31 7.56 8.31 7.56 8.56 7.81 9.383 1.375 1.31 4.47 3.13 5.38 2.00 6.19 7.44 8.19 7.44 8.44 7.68 9.26

3.251 (std) 1.375 1.68 4.84 3.51 6.13 2.19 6.94 8.44 9.44 8.44 9.69 8.83 10.80

2 2.000 1.68 4.84 3.51 6.13 2.19 7.13 8.63 9.63 8.63 9.88 9.01 10.983 1.750 1.68 4.84 3.51 6.13 2.19 7.06 8.56 9.56 8.56 9.81 8.95 10.92

4.001 (std) 1.750 1.44 5.15 3.82 6.50 2.50 7.44 9.56 10.94 9.56 11.44 9.72 12.16

2 2.500 1.44 5.15 3.82 6.50 2.50 7.56 9.69 11.06 9.69 11.56 9.84 12.283 2.000 1.44 5.15 3.82 6.50 2.50 7.50 9.62 11.00 9.62 11.50 9.78 12.22

5.00

1 (std) 2.000 1.79 5.59 4.26 7.12 2.56 8.12 10.37 12.12 10.37 12.87 10.95 14.102 3.500 1.79 5.59 4.26 7.12 2.56 8.18 10.43 12.18 10.43 12.93 11.01 14.163 2.500 1.79 5.59 4.26 7.12 2.56 8.18 10.43 12.18 10.43 12.93 11.01 14.164 3.000 1.79 5.59 4.26 7.12 2.56 8.18 10.43 12.18 10.43 12.93 11.01 14.16

6.00

1 (std) 2.500 2.36 6.09 4.76 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.992 4.000 2.36 6.09 4.76 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.993 3.000 2.36 6.09 4.76 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.994 3.500 2.36 6.09 4.76 8.37 3.00 9.43 11.93 13.93 11.93 14.43 13.05 16.99

7.00

1 (std) 3.000 2.67 6.59 5.26 9.00 3.25 10.06 13.06 15.56

N/A

14.63 18.572 5.000 2.67 6.59 5.26 9.00 3.25 10.19 13.19 15.69 14.75 18.693 3.500 2.67 6.59 5.26 9.00 3.25 10.06 13.06 15.56 14.63 18.574 4.000 2.67 6.59 5.26 9.00 3.25 10.06 13.06 15.56 14.63 18.575 4.500 2.67 6.59 5.26 9.00 3.25 10.19 13.19 15.69 14.75 18.69

8.00

1 (std) 3.500 2.96 7.09 5.76 9.50 3.25 10.56 13.81 16.56 15.12 19.852 5.500 2.96 7.09 5.76 9.50 3.25 10.68 13.93 16.68 15.25 19.973 4.000 2.96 7.09 5.76 9.50 3.25 10.56 13.81 16.56 15.12 19.854 4.500 2.96 7.09 5.76 9.50 3.25 10.68 13.93 16.68 15.25 19.975 5.000 2.96 7.09 5.76 9.50 3.25 10.58 13.93 16.68 15.25 19.97

Styles T & DD

Styles SB & SBM

Styles B & BBLB + STROKE

ZJ + STROKE

HS

P + STROKE

ER

LB + STROKE


P + STROKE

HS

ER

LB + STROKE


HS

ER

P + STROKE




49

C


Switch on Cap End

Bore Ø

Rod No.

MM Rod

Ø

All Mountings Styles J/JP Style H Style TT

HS ER YF Add Stroke EH Add Stroke ER Add StrokeCLS-A EPS-A LG PJ ZG LH P XF ZF LB P XC ZC

1.501 (std) 0.625 4.49 2.66 0.83 2.75 4.06 1.32 4.87 1.08 3.56 1.32 4.12 4.50 0.83 3.69 1.32 4.87 5.50

2 1.000 4.49 2.66 0.83 3.25 4.06 1.32 5.38 1.08 3.94 1.32 4.63 5.00 0.83 4.06 1.32 5.38 6.00

2.001 (std) 1.000 4.25 2.91 1.12 3.26 5.44 2.06 6.38 1.43 4.81 2.06 5.50 5.94 1.12 4.94 2.06 6.25 6.88

2 1.375 4.25 2.91 1.12 3.38 5.44 2.06 6.50 1.43 4.81 2.06 5.62 6.06 1.12 4.94 2.06 6.37 7.00

2.501 (std) 1.000 4.47 3.13 1.31 3.44 5.88 2.00 6.81 1.68 5.25 2.00 5.94 6.44 1.31 5.38 2.00 6.81 7.56

2 1.750 4.47 3.13 1.31 3.69 5.88 2.00 7.06 1.68 5.25 2.00 6.19 6.69 1.31 5.38 2.00 7.06 7.813 1.375 4.47 3.13 1.31 3.56 5.88 2.00 6.94 1.68 5.25 2.00 6.06 6.56 1.31 5.38 2.00 6.94 7.69

3.251 (std) 1.375 4.84 3.51 1.68 3.81 6.63 2.19 7.69 2.18 6.00 2.19 6.81 7.44 1.68 6.13 2.19 7.87 8.81

2 2.000 4.84 3.51 1.68 4.00 6.63 2.19 7.88 2.18 6.00 2.19 7.00 7.63 1.68 6.13 2.19 8.06 9.003 1.750 4.84 3.51 1.68 3.94 6.63 2.19 7.81 2.18 6.00 2.19 6.94 7.56 1.68 6.13 2.19 8.00 8.94

4.001 (std) 1.750 5.15 3.82 1.44 4.15 7.00 2.50 8.19 2.07 6.37 2.50 7.31 8.06 1.44 6.50 2.50 8.44 9.44

2 2.500 5.15 3.82 1.44 4.27 7.00 2.50 8.31 2.07 6.37 2.50 7.44 8.19 1.44 6.50 2.50 8.56 9.563 2.000 5.15 3.82 1.44 4.21 7.00 2.50 8.25 2.07 6.37 2.50 7.37 8.12 1.44 6.50 2.50 8.50 9.50

5.00

1 (std) 2.000 5.59 4.26 1.79 4.45 7.55 2.56 8.87 2.54 6.99 2.56 7.99 8.87 1.79 7.12 2.56 9.49 10.872 3.500 5.59 4.26 1.79 4.51 7.55 2.56 8.93 2.54 6.99 2.56 8.05 8.93 1.79 7.12 2.56 9.55 10.933 2.500 5.59 4.26 1.79 4.51 7.55 2.56 8.93 2.54 6.99 2.56 8.05 8.93 1.79 7.12 2.56 9.55 10.934 3.000 5.59 4.26 1.79 4.51 7.55 2.56 8.93 2.54 6.99 2.56 8.05 8.93 1.79 7.12 2.56 9.55 10.93

6.00

1 (std) 2.500 6.09 4.76 2.36 4.99 8.75 3.00 10.18 3.24 8.25 3.00 9.31 10.31 2.36 8.37 3.00 10.93 12.432 4.000 6.09 4.76 2.36 4.99 8.75 3.00 10.18 3.24 8.25 3.00 9.31 10.31 2.36 8.37 3.00 10.93 12.433 3.000 6.09 4.76 2.36 4.99 8.75 3.00 10.18 3.24 8.25 3.00 9.31 10.31 2.36 8.37 3.00 10.93 12.434 3.500 6.09 4.76 2.36 4.99 8.75 3.00 10.18 3.24 8.25 3.00 9.31 10.31 2.36 8.37 3.00 10.93 12.43

7.00

1 (std) 3.000 6.59 5.26 2.67 5.25 9.63 3.25 11.06 3.55 8.88 3.25 9.94 10.94 2.67 9.00 3.25 11.94 13.812 5.000 6.59 5.26 2.67 5.38 9.63 3.25 11.19 3.55 8.88 3.25 10.06 11.06 2.67 9.00 3.25 12.06 13.943 3.500 6.59 5.26 2.67 5.25 9.63 3.25 11.06 3.55 8.88 3.25 9.94 10.94 2.67 9.00 3.25 11.94 13.814 4.000 6.59 5.26 2.67 5.25 9.63 3.25 11.06 3.55 8.88 3.25 9.94 10.94 2.67 9.00 3.25 11.94 13.815 4.500 6.59 5.26 2.67 5.38 9.63 3.25 11.19 3.55 8.88 3.25 10.06 11.06 2.67 9.00 3.25 12.06 13.94

8.00

1 (std) 3.500 7.09 5.76 2.96 5.44 10.00 3.25 11.56 3.96 9.37 3.25 10.43 11.56 2.96 9.50 3.25 12.56 14.562 5.500 7.09 5.76 2.96 5.56 10.00 3.25 11.68 3.96 9.37 3.25 10.56 11.68 2.96 9.50 3.25 12.68 14.683 4.000 7.09 5.76 2.96 5.44 10.00 3.25 11.56 3.96 9.37 3.25 10.43 11.56 2.96 9.50 3.25 12.56 14.564 4.500 7.09 5.76 2.96 5.56 10.00 3.25 11.68 3.96 9.37 3.25 10.56 11.68 2.96 9.50 3.25 12.68 14.685 5.000 7.09 5.76 2.96 5.56 10.00 3.25 11.68 3.96 9.37 3.25 10.56 11.68 2.96 9.50 3.25 12.68 14.68

Styles J/JP1

Style TT

Style H1


HS

ER

YF PJ + STROKE XF + STROKELH + STROKE

ZF + STROKE

HS

EH

P + STROKE

LB + STROKE


HS

ER

P + STROKE

1 SeeportandswitchpositionnoteonmountingStylesJ/JP&Hpages.




50


Switch on K-Type – Both Ends

Styles KJ/KJP1

Styles KT & KDD

LJ + STROKEZN + STROKE

HSHS

EJ EN

YF PK + STROKE

LD + STROKEZM + STROKE

HSHS

ENEN

PK + STROKE

1 See port and switch position note on mounting Styles J/JP dimension page.

Bore Ø

Rod No.

MM Rod

Ø

Styles KT, KDD & KJ / KJP Style KT & KDD

Styles KJ / KJP

EN HS Add Stroke LD ZM EJ YF LJ ZN

CLS-A EPS-A CLS-A EPS-A PK CLS-A EPS-A

1.501 (std) 0.625 1.63 1.63 4.49 2.66 1.91 5.03 6.10 2.01 2.01 2.75 5.40 6.73

2 1.000 2.01 2.01 4.49 2.66 1.91 5.78 7.10 2.01 2.01 3.25 5.78 7.73

2.001 (std) 1.000 2.31 2.20 4.25 2.91 3.26 6.90 7.66 2.44 2.33 3.26 7.03 8.03

2 1.375 2.31 2.20 4.25 2.91 3.26 6.90 7.90 2.44 2.33 3.38 7.03 8.28

2.501 (std) 1.000 2.56 2.45 4.47 3.13 3.40 7.40 8.16 2.69 2.58 3.44 7.53 8.53

2 1.750 2.56 2.45 4.47 3.13 3.40 7.40 8.66 2.69 2.58 3.69 7.53 9.033 1.375 2.56 2.45 4.47 3.13 3.40 7.40 8.40 2.69 2.58 3.56 7.53 8.78

3.251 (std) 1.375 2.81 2.70 4.84 3.51 3.53 8.03 9.03 2.94 2.83 3.81 8.15 9.40

2 2.000 2.81 2.70 4.84 3.51 3.53 8.03 9.41 2.94 2.83 4.00 8.15 9.783 1.750 2.81 2.70 4.84 3.51 3.53 8.03 9.28 2.94 2.83 3.94 8.15 9.66

4.001 (std) 1.750 3.06 2.95 5.15 3.82 3.86 8.78 9.91 3.06 2.95 4.15 8.78 10.16

2 2.500 3.06 2.95 5.15 3.82 3.86 8.78 10.15 3.06 2.95 4.27 8.78 10.403 2.000 3.06 2.95 5.15 3.82 3.86 8.78 10.03 3.06 2.95 4.21 8.78 10.28

5.00

1 (std) 2.000 3.31 3.20 5.59 4.26 4.00 9.40 10.66 3.25 3.14 4.45 9.34 10.912 3.500 3.31 3.20 5.59 4.26 4.00 9.40 10.78 3.25 3.14 4.51 9.34 11.033 2.500 3.31 3.20 5.59 4.26 4.00 9.40 10.78 3.25 3.14 4.51 9.34 11.034 3.000 3.31 3.20 5.59 4.26 4.00 9.40 10.78 3.25 3.14 4.51 9.34 11.03

6.00

1 (std) 2.500 3.19 3.14 6.09 4.76 2.92 9.28 11.28 3.56 3.51 4.99 9.65 12.032 4.000 3.19 3.14 6.09 4.76 2.92 9.28 11.28 3.56 3.51 4.99 9.65 12.033 3.000 3.19 3.14 6.09 4.76 2.92 9.28 11.28 3.56 3.51 4.99 9.65 12.034 3.500 3.19 3.14 6.09 4.76 2.92 9.28 11.28 3.56 3.51 4.99 9.65 12.03

7.00

1 (std) 3.000 3.20 3.08 6.59 5.26 3.16 9.54 11.67 3.82 3.70 5.25 10.16 12.672 5.000 3.20 3.08 6.59 5.26 3.16 9.54 11.92 3.82 3.70 5.38 10.16 12.923 3.500 3.20 3.08 6.59 5.26 3.16 9.54 11.67 3.82 3.70 5.25 10.16 12.674 4.000 3.20 3.08 6.59 5.26 3.16 9.54 11.67 3.82 3.70 5.25 10.16 12.675 4.500 3.20 3.08 6.59 5.26 3.16 9.54 11.92 3.82 3.70 5.38 10.16 12.92

8.00

1 (std) 3.500 3.41 3.29 7.09 5.76 3.21 9.96 12.09 3.91 3.79 5.44 10.46 13.092 5.500 3.41 3.29 7.09 5.76 3.21 9.96 12.34 3.91 3.79 5.56 10.46 13.343 4.000 3.41 3.29 7.09 5.76 3.21 9.96 12.09 3.91 3.79 5.44 10.46 13.094 4.500 3.41 3.29 7.09 5.76 3.21 9.96 12.34 3.91 3.79 5.56 10.46 13.345 5.000 3.41 3.29 7.09 5.76 3.21 9.96 12.34 3.91 3.79 5.56 10.46 13.34




51

C


Switch on K-Type – End 1 Only

Styles KJ/KJP1

Styles KT & KDD


HS

EJ

YF PK + STROKE


HS

EN

PK + STROKE

1 See port and switch position note on mounting Style J dimension page.

Bore Ø

Rod No.

MM Rod

Ø

Styles KT, KDD & KJ / KJP Styles KT & KDD

Styles KJ / KJP

EN HS Add Stroke EJ YF LJ ZN

CLS-A EPS-A CLS-A EPS-A PK LD ZM CLS-A EPS-A

1.501 (std) 0.625 1.63 1.63 4.49 2.66 1.72 4.84 5.98 2.01 2.01 2.75 5.21 6.60

2 1.000 2.01 2.01 4.49 2.66 1.72 5.59 6.98 2.01 2.01 3.25 5.59 7.60

2.001 (std) 1.000 2.31 2.20 4.25 2.91 2.51 6.15 7.53 2.44 2.33 3.26 6.28 7.91

2 1.375 2.31 2.20 4.25 2.91 2.51 6.15 7.78 2.44 2.33 3.38 6.28 8.15

2.501 (std) 1.000 2.56 2.45 4.47 3.13 2.65 6.65 8.03 2.69 2.58 3.44 6.78 8.41

2 1.750 2.56 2.45 4.47 3.13 2.65 6.65 8.53 2.69 2.58 3.69 6.78 8.913 1.375 2.56 2.45 4.47 3.13 2.65 6.65 8.28 2.69 2.58 3.56 6.78 8.65

3.251 (std) 1.375 2.81 2.70 4.84 3.51 2.78 7.28 8.90 2.94 2.83 3.81 7.40 9.28

2 2.000 2.81 2.70 4.84 3.51 2.78 7.28 9.28 2.94 2.83 4.00 7.40 9.663 1.750 2.81 2.70 4.84 3.51 2.78 7.28 9.16 2.94 2.83 3.94 7.40 9.53

4.001 (std) 1.750 3.06 2.95 5.15 3.82 3.11 8.03 9.91 3.06 2.95 4.15 8.03 10.16

2 2.500 3.06 2.95 5.15 3.82 3.11 8.03 10.15 3.06 2.95 4.27 8.03 10.403 2.000 3.06 2.95 5.15 3.82 3.11 8.03 10.03 3.06 2.95 4.21 8.03 10.28

5.00

1 (std) 2.000 3.31 3.20 5.59 4.26 3.25 8.65 10.66 3.25 3.14 4.45 8.59 10.912 3.500 3.31 3.20 5.59 4.26 3.25 8.65 10.78 3.25 3.14 4.51 8.59 11.033 2.500 3.31 3.20 5.59 4.26 3.25 8.65 10.78 3.25 3.14 4.51 8.59 11.034 3.000 3.31 3.20 5.59 4.26 3.25 8.65 10.78 3.25 3.14 4.51 8.59 11.03

6.00

1 (std) 2.500 3.19 3.14 6.09 4.76 2.79 9.15 11.28 3.56 3.51 4.99 9.53 12.032 4.000 3.19 3.14 6.09 4.76 2.79 9.15 11.28 3.56 3.51 4.99 9.53 12.033 3.000 3.19 3.14 6.09 4.76 2.79 9.15 11.28 3.56 3.51 4.99 9.53 12.034 3.500 3.19 3.14 6.09 4.76 2.79 9.15 11.28 3.56 3.51 4.99 9.53 12.03

7.00

1 (std) 3.000 3.20 3.08 6.59 5.26 3.16 9.54 11.67 3.82 3.70 5.25 10.16 12.672 5.000 3.20 3.08 6.59 5.26 3.16 9.54 11.92 3.82 3.70 5.38 10.16 12.923 3.500 3.20 3.08 6.59 5.26 3.16 9.54 11.67 3.82 3.70 5.25 10.16 12.674 4.000 3.20 3.08 6.59 5.26 3.16 9.54 11.67 3.82 3.70 5.25 10.16 12.675 4.500 3.20 3.08 6.59 5.26 3.16 9.54 11.92 3.82 3.70 5.38 10.16 12.92

8.00

1 (std) 3.500 3.41 3.29 7.09 5.76 3.21 9.96 12.09 3.91 3.79 5.44 10.46 13.092 5.500 3.41 3.29 7.09 5.76 3.21 9.96 12.34 3.91 3.79 5.56 10.46 13.343 4.000 3.41 3.29 7.09 5.76 3.21 9.96 12.09 3.91 3.79 5.44 10.46 13.094 4.500 3.41 3.29 7.09 5.76 3.21 9.96 12.34 3.91 3.79 5.56 10.46 13.345 5.000 3.41 3.29 7.09 5.76 3.21 9.96 12.34 3.91 3.79 5.56 10.46 13.34




52


Switch on K-Type – End 2 Only

Styles KJ/KJP1

Styles KT & KDD


HS

EN

YF PK + STROKE


HS

EN

PK + STROKE

1 See port and switch position note on mounting Style J dimension page.

Rod No.

MM Rod

Ø

Styles KT, KDD & KJ / KJP Styles KT & KDD

Styles KJ / KJP

EN HS Add Stroke EJ YF LJ ZN

CLS-A EPS-A CLS-A EPS-A PK LD ZM CLS-A EPS-A1 (std) 0.625 1.63 1.63 4.49 2.66 1.41 4.53 5.60 2.01 2.01 2.75 4.90 6.23

2 1.000 2.01 2.01 4.49 2.66 1.41 5.28 6.60 2.01 2.01 3.25 5.28 7.231 (std) 1.000 2.31 2.20 4.25 2.91 2.51 6.15 6.91 2.44 2.33 3.26 6.65 7.66

2 1.375 2.31 2.20 4.25 2.91 2.51 6.15 7.15 2.44 2.33 3.38 6.65 7.901 (std) 1.000 2.56 2.45 4.47 3.13 2.65 6.65 7.41 2.69 2.58 3.44 7.15 8.16

2 1.750 2.56 2.45 4.47 3.13 2.65 6.65 7.91 2.69 2.58 3.69 7.15 8.663 1.375 2.56 2.45 4.47 3.13 2.65 6.65 7.65 2.69 2.58 3.56 7.15 8.40

1 (std) 1.375 2.81 2.70 4.84 3.51 2.78 7.28 8.28 2.94 2.83 3.81 7.78 9.032 2.000 2.81 2.70 4.84 3.51 2.78 7.28 8.66 2.94 2.83 4.00 7.78 9.413 1.750 2.81 2.70 4.84 3.51 2.78 7.28 8.53 2.94 2.83 3.94 7.78 9.28

1 (std) 1.750 3.06 2.95 5.15 3.82 3.11 8.03 9.16 3.06 2.95 4.15 8.53 9.912 2.500 3.06 2.95 5.15 3.82 3.11 8.03 9.40 3.06 2.95 4.27 8.53 10.153 2.000 3.06 2.95 5.15 3.82 3.11 8.03 9.28 3.06 2.95 4.21 8.53 10.03

1 (std) 2.000 3.31 3.20 5.59 4.26 3.25 8.65 9.91 3.25 3.14 4.45 9.09 10.662 3.500 3.31 3.20 5.59 4.26 3.25 8.65 10.03 3.25 3.14 4.51 9.09 10.783 2.500 3.31 3.20 5.59 4.26 3.25 8.65 10.03 3.25 3.14 4.51 9.09 10.784 3.000 3.31 3.20 5.59 4.26 3.25 8.65 10.03 3.25 3.14 4.51 9.09 10.78

1 (std) 2.500 3.19 3.14 6.09 4.76 2.92 9.28 11.28 3.56 3.51 4.99 9.65 12.032 4.000 3.19 3.14 6.09 4.76 2.92 9.28 11.28 3.56 3.51 4.99 9.65 12.033 3.000 3.19 3.14 6.09 4.76 2.92 9.28 11.28 3.56 3.51 4.99 9.65 12.034 3.500 3.19 3.14 6.09 4.76 2.92 9.28 11.28 3.56 3.51 4.99 9.65 12.03

1 (std) 3.000 3.20 3.08 6.59 5.26 3.16 9.54 11.67 3.82 3.70 5.25 10.16 12.672 5.000 3.20 3.08 6.59 5.26 3.16 9.54 11.92 3.82 3.70 5.38 10.16 12.923 3.500 3.20 3.08 6.59 5.26 3.16 9.54 11.67 3.82 3.70 5.25 10.16 12.674 4.000 3.20 3.08 6.59 5.26 3.16 9.54 11.67 3.82 3.70 5.25 10.16 12.675 4.500 3.20 3.08 6.59 5.26 3.16 9.54 11.92 3.82 3.70 5.38 10.16 12.92

1 (std) 3.500 3.41 3.29 7.09 5.76 3.21 9.96 12.09 3.91 3.79 5.44 10.46 13.092 5.500 3.41 3.29 7.09 5.76 3.21 9.96 12.34 3.91 3.79 5.56 10.46 13.343 4.000 3.41 3.29 7.09 5.76 3.21 9.96 12.09 3.91 3.79 5.44 10.46 13.094 4.500 3.41 3.29 7.09 5.76 3.21 9.96 12.34 3.91 3.79 5.56 10.46 13.345 5.000 3.41 3.29 7.09 5.76 3.21 9.96 12.34 3.91 3.79 5.56 10.46 13.34




53

C

Notes

Notes




54

Counterbalance Valves

• Offerhosebreakprotection • Preventloadsfromdrifting • Controloverrunningloads • Provideovercenterloadcontrol • Protectagainstpressureduetothermalexpansion

Counterbalance valves can be supplied for control of both extend and retract stroke or only in one stroke direction. The valve manifold can be installed on either the head end or cap end. Carbon steel hydraulic tubing connects the valvemanifoldtotheoppositeendport.ALenzfittinginthemanifold port is plumbed to a matched SAE size zinc plated Triple-Lokfittinginthecylinderport.

Port Mounted Counterbalance Valves Add Versatility to Series RDH Cylinders

Required information for selecting the correct Counterbalance Valve for your application: 1.OilflowthroughtheportinGPM 2. System operating pressure in psi 3. Pressure (psi) to hold the load 4.Valvemanifoldlocation–headorcap 5.Controlofbothextendandretractstrokeoronlyin one stroke direction

Note – control of only one stroke direction affects the required manifold location: – Manifoldmustbemountedatthecapendfor retract stroke control and load holding – Manifoldmustbemountedattheheadendfor extend stroke control and load holding

V2

V1

C1

C2

V2

V1

C1

C2

Single Counterbalance, Cap Mounted

Single Counterbalance, Head Mounted

Many functional options are available to suit a wide variety of applications: • 3ValveManifoldsizeswith3flowchoicespersize • 3standardpressuresettings–1,000,2,000 and 3,000 psi • 4standardpressureadjustmentranges • 2pilotratios–3to1or4.5to1 • Class1(standard)orClass5seals(contactthe factory for other seal classes)

Double Counterbalance, Cap Mounted

Double Counterbalance, Head Mounted

V2

V1

C1

C2

V2

V1

C1

C2




55

C


RDH Counterbalance Valve Manifold Assembly Ordering CodeCounterbalanceValvescanbeorderedonSeriesRDHcylindersasfollows. 1) Complete the basic cylinder model number. 2)Placean'S'inthemodelnumbertodenoteSpecialModifications. 3)SpecifytheCounterbalanceValveManifoldoptionOrderingCodebymakingselections from the categories below.

A S A C CA H N A - 3000 / 2500Valve Manifold SizeA–SAE6Port-5GPM1

B–SAE8Port-10GPM1

C–SAE12Port-20GPM1

D–SAE16Port-40GPM1

Single or Double ValveS–Single–ControlinonedirectionD–Double–Controlinbothdirections

Valve Manifold MaterialA–AluminumD–DuctileIron

Cap End or Head End MountedC–CapEndMountedH–HeadEndMounted

Counterbalance Valve Capacity & Pilot RatioSee Table A

Pressure RangeValveswith3to1PilotRatioH–1000to4000psi(3000psistd.setting)I –400to1500psi(1000psistd.setting)Valveswith4.5to1PilotRatioJ–2000to5000psi(3000psistd.setting)K–1000to2500psi(2000psistd.setting)

SealsN–NBR-NitrileV–FKM-Fluorocarbon

Valve AdjustmentA–ScrewAdjust(Std)T–withTamperResistCover

Pressure Setting SingleValveManifold–pressuresettingofcounterbalancevalve(psi)orDoubleValveManifold–pressuresettingofcounterbalancevalveonC1port(psi)Pressure Setting – C2 Port (Double Valve Manifold Only)DoubleValveManifold-pressuresettingofcounterbalancevalveonC2port(psi)

1Nominalflowforportsizeat25fpsvelocity.

Table A - Counterbalance Valve Capacity & Pilot RatioCounterbalance Valve Capacity

Valve Manifold Size A Valve Manifold Size B Valve Manifold Sizes C & D

Rated Max. Flow (GPM)

Pilot Ratio

Order Code


Pilot Ratio

Order Code


Pilot Ratio

Order Code

Standard 15 3:1 CA 30 3:1 EA 60 3:1 GAStandard 15 4.5:1 CG 30 4.5:1 EG 60 4.5:1 GG

Semi-Restrictive 10 3:1 BC 20 3:1 DC 40 3:1 FCSemi-Restrictive 10 4.5:1 BD 20 4.5:1 DD 40 4.5:1 FD

Restrictive 5 3:1 BA 8 3:1 DA 15 3:1 FARestrictive 5 4.5:1 BG 8 4.5:1 DG 15 4.5:1 FG




56


Counterbalance Valve Control of One Stroke Direction Only – Dimensions

MH BC

ML RV

RV ML

BC MC

FHMT

EH

MWMO

HP

CP

EE (V2 - RETRACT)RH

EE (V1 - EXTEND)

HF

Bore Ø

Rod No.

Manifold Size

Min. Stroke

BC CP EE SAE

EH FH HF HP MC1 MH ML MO MT MW RH RV

1.50 1 A 5.50 1.00 0.96 6 0.59 1.79 3.00 0.22 -0.19 0.56 3.75 1.46 1.18 2.50 0.59 1.272 A 5.50 1.00 0.96 6 0.59 1.79 3.00 0.22 -0.19 0.94 3.75 1.46 1.18 2.50 0.59 1.27

2.00 All A 4.95 1.00 0.96 6 0.59 2.04 3.39 0.22 0.06 0.82 3.75 1.46 1.18 2.50 0.59 1.27B 5.86 1.21 1.16 8 0.71 2.12 3.52 0.28 -0.15 0.61 4.25 1.78 1.43 3.00 0.71 1.63

2.50 All A 5.00 1.00 0.96 6 0.59 2.37 3.73 0.22 0.38 1.00 3.75 1.46 1.18 2.50 0.59 1.27B 5.92 1.21 1.16 8 0.71 2.43 3.84 0.28 0.17 0.79 4.25 1.78 1.43 3.00 0.71 1.63

3.25 All

A 4.81 1.00 0.96 6 0.59 2.81 4.16 0.22 0.69 1.25 3.75 1.46 1.18 2.50 0.59 1.27B 5.73 1.21 1.16 8 0.71 2.81 4.21 0.28 0.48 1.04 4.25 1.78 1.43 3.00 0.71 1.63C 7.63 1.43 1.68 12 1.09 3.18 4.82 0.50 0.26 0.82 5.46 2.43 2.18 4.00 1.09 1.69D 8.28 1.43 1.53 16 1.09 3.18 5.07 0.66 0.26 0.82 5.46 2.43 2.18 4.00 1.09 1.69

4.00 All

A 4.38 1.00 0.96 6 0.59 3.17 4.53 0.22 0.54 1.46 3.75 1.46 1.18 2.50 0.59 1.27B 5.29 1.21 1.16 8 0.71 3.19 4.60 0.28 0.33 1.25 4.25 1.78 1.43 3.00 0.71 1.63C 7.19 1.43 1.68 12 1.09 3.57 5.20 0.50 0.11 1.03 5.46 2.43 2.18 4.00 1.09 1.69D 7.84 1.43 1.53 16 1.09 3.57 5.46 0.66 0.11 1.03 5.46 2.43 2.18 4.00 1.09 1.69

5.00 All

A 4.31 1.00 0.96 6 0.59 3.75 5.10 0.22 0.86 1.70 3.75 1.46 1.18 2.50 0.59 1.27B 5.23 1.21 1.16 8 0.71 3.80 5.20 0.28 0.65 1.49 4.25 1.78 1.43 3.00 0.71 1.63C 7.13 1.43 1.68 12 1.09 4.17 5.81 0.50 0.43 1.27 5.46 2.43 2.18 4.00 1.09 1.69D 7.78 1.43 1.53 16 1.09 4.17 6.06 0.66 0.43 1.27 5.46 2.43 2.18 4.00 1.09 1.69

6.00 All

A 3.87 1.00 0.96 6 0.59 4.37 5.73 0.22 1.19 2.18 3.75 1.46 1.18 2.50 0.59 1.27B 4.79 1.21 1.16 8 0.71 4.42 5.83 0.28 0.98 1.97 4.25 1.78 1.43 3.00 0.71 1.63C 6.69 1.43 1.68 12 1.09 4.80 6.43 0.50 0.76 1.75 5.46 2.43 2.18 4.00 1.09 1.69D 7.34 1.43 1.53 16 1.09 4.80 6.69 0.66 0.76 1.75 5.46 2.43 2.18 4.00 1.09 1.69

7.00 All

A 3.63 1.00 0.96 6 0.59 4.87 6.23 0.22 1.56 2.19 3.75 1.46 1.18 2.50 0.59 1.27B 4.54 1.21 1.16 8 0.71 4.92 6.33 0.28 1.35 1.98 4.25 1.78 1.43 3.00 0.71 1.63C 6.44 1.43 1.68 12 1.09 5.30 6.93 0.50 1.13 1.76 5.46 2.43 2.18 4.00 1.09 1.69D 7.09 1.43 1.53 16 1.09 5.30 7.19 0.66 1.13 1.76 5.46 2.43 2.18 4.00 1.09 1.69

8.00 All

A 3.63 1.00 0.96 6 0.59 5.50 6.85 0.22 1.87 2.38 3.75 1.46 1.18 2.50 0.59 1.27B 4.54 1.21 1.16 8 0.71 5.55 6.95 0.28 1.66 2.17 4.25 1.78 1.43 3.00 0.71 1.63C 6.44 1.43 1.68 12 1.09 5.92 7.56 0.50 1.44 1.95 5.46 2.43 2.18 4.00 1.09 1.69D 7.09 1.43 1.53 16 1.09 5.92 7.81 0.66 1.44 1.95 5.46 2.43 2.18 4.00 1.09 1.69

1 Negative values indicate valve block extension beyond rear of cap. Check rear mounting styles (especially pivot mounts) for possible interference with a cap mounted manifold.




57

C

Counterbalance Valve Control of Both Extend and Retract Strokes – Dimensions

MH BC

CV ML RV

RV ML CV

BC MC

FHEH

RH

MT

MW

HP

CPEE (V1 - EXTEND)

EE (V2 - RETRACT)

MO

HF

Bore Ø

Rod No.

Manifold Size

Min. Stroke

BC CP CV EE SAE

EH FH HF HP MC1 MH ML MO MT MW RH RV

1.50 1 A 5.50 1.00 0.96 1.28 6 0.59 1.79 3.00 0.25 -0.19 1.56 3.75 1.46 2.18 2.50 0.50 1.272 A 5.50 1.00 0.96 1.28 6 0.59 1.79 3.00 0.25 -0.19 1.94 3.75 1.46 2.18 2.50 0.50 1.27

2.00 All A 4.95 1.00 0.96 1.28 6 0.59 2.04 3.39 0.25 0.06 1.82 3.75 1.46 2.18 2.50 0.50 1.27B 5.86 1.21 1.16 1.32 8 0.81 2.12 3.52 0.22 -0.15 1.82 4.25 1.78 2.75 3.00 0.62 1.63

2.50 All A 5.00 1.00 0.96 1.28 6 0.59 2.37 3.73 0.25 0.38 2.00 3.75 1.46 2.18 2.50 0.50 1.27B 5.92 1.21 1.16 1.32 8 0.81 2.43 3.84 0.22 0.17 2.00 4.25 1.78 2.75 3.00 0.62 1.63

3.25 All

A 4.81 1.00 0.96 1.28 6 0.59 2.81 4.16 0.25 0.69 2.25 3.75 1.46 2.18 2.50 0.50 1.27B 5.73 1.21 1.16 1.32 8 0.81 2.81 4.21 0.22 0.48 2.25 4.25 1.78 2.75 3.00 0.62 1.63C 7.63 1.43 1.68 1.69 12 1.43 3.18 4.82 0.00 0.26 2.25 5.46 2.43 3.93 4.00 1.18 1.69D 8.28 1.43 1.53 1.69 16 1.93 3.18 5.07 0.35 0.26 2.25 5.46 2.43 3.93 4.00 1.09 1.69

4.00 All

A 4.38 1.00 0.96 1.28 6 0.59 3.17 4.53 0.25 0.54 2.46 3.75 1.46 2.18 2.50 0.50 1.27B 5.29 1.21 1.16 1.32 8 0.81 3.19 4.60 0.22 0.33 2.46 4.25 1.78 2.75 3.00 0.62 1.63C 7.19 1.43 1.68 1.69 12 1.43 3.57 5.20 0.00 0.11 2.46 5.46 2.43 3.93 4.00 1.18 1.69D 7.84 1.43 1.53 1.69 16 1.93 3.57 5.46 0.35 0.11 2.46 5.46 2.43 3.93 4.00 1.09 1.69

5.00 All

A 4.31 1.00 0.96 1.28 6 0.59 3.75 5.10 0.25 0.86 2.70 3.75 1.46 2.18 2.50 0.50 1.27B 5.23 1.21 1.16 1.32 8 0.81 3.80 5.20 0.22 0.65 2.70 4.25 1.78 2.75 3.00 0.62 1.63C 7.13 1.43 1.68 1.69 12 1.43 4.17 5.81 0.00 0.43 2.70 5.46 2.43 3.93 4.00 1.18 1.69D 7.78 1.43 1.53 1.69 16 1.93 4.17 6.06 0.35 0.43 2.70 5.46 2.43 3.93 4.00 1.09 1.69

6.00 All

A 3.87 1.00 0.96 1.28 6 0.59 4.37 5.73 0.25 1.19 3.18 3.75 1.46 2.18 2.50 0.50 1.27B 4.79 1.21 1.16 1.32 8 0.81 4.42 5.83 0.22 0.98 3.18 4.25 1.78 2.75 3.00 0.62 1.63C 6.69 1.43 1.68 1.69 12 1.43 4.80 6.43 0.00 0.76 3.18 5.46 2.43 3.93 4.00 1.18 1.69D 7.34 1.43 1.53 1.69 16 1.93 4.80 6.69 0.35 0.76 3.18 5.46 2.43 3.93 4.00 1.09 1.69

7.00 All

A 3.63 1.00 0.96 1.28 6 0.59 4.87 6.23 0.25 1.56 3.19 3.75 1.46 2.18 2.50 0.50 1.27B 4.54 1.21 1.16 1.32 8 0.81 4.92 6.33 0.22 1.35 3.19 4.25 1.78 2.75 3.00 0.62 1.63C 6.44 1.43 1.68 1.69 12 1.43 5.30 6.93 0.00 1.13 3.19 5.46 2.43 3.93 4.00 1.18 1.69D 7.09 1.43 1.53 1.69 16 1.93 5.30 7.19 0.35 1.13 3.19 5.46 2.43 3.93 4.00 1.09 1.69

8.00 All

A 3.63 1.00 0.96 1.28 6 0.59 5.50 6.85 0.25 1.87 3.38 3.75 1.46 2.18 2.50 0.50 1.27B 4.54 1.21 1.16 1.32 8 0.81 5.55 6.95 0.22 1.66 3.38 4.25 1.78 2.75 3.00 0.62 1.63C 6.44 1.43 1.68 1.69 12 1.43 5.92 7.56 0.00 1.44 3.38 5.46 2.43 3.93 4.00 1.18 1.69D 7.09 1.43 1.53 1.69 16 1.93 5.92 7.81 0.35 1.44 3.38 5.46 2.43 3.93 4.00 1.09 1.69

1 Negative values indicate valve block extension beyond rear of cap. Check rear mounting styles (especially pivot mounts) for possible interference with a cap mounted manifold.





58

Notes

Notes




59

C

Notes

Notes

Heavy Duty Hydraulic Roundline CylindersEngineering Data



60

Theoretical Push and Pull Forces

General FormulaThe cylinder output forces are derived from the formula: F=Px A

Theoretical Push Forces for Cylinders Cylinder

Bore Ø

Piston Area (In.2)

Cylinder Push Stroke Force in Pounds at Various Pressures (psi)

100 250 500 1000 1500 2000 30001.50 1.77 177 443 885 1770 2651 3540 53102.00 3.14 314 785 1570 3140 4712 6280 94202.50 4.91 491 1228 2455 4910 7363 9820 147303.25 8.30 830 2075 4150 8300 12444 16600 249004.00 12.57 1257 3143 6285 12570 18850 25140 377105.00 19.64 1964 4910 9820 19640 29453 39280 589206.00 28.27 2827 7068 14135 28270 42412 56540 848107.00 38.49 3849 9623 19245 38490 57727 76980 1154708.00 50.27 5027 12568 25135 50270 75398 100540 150810

Theoretical Pull Forces for Cylinders Bore

ØPiston Rod

Ø

Piston Rod Area

(In.2)

Cylinder Pull Force in Pounds at Various Pressures (psi)

100 250 500 1000 1500 2000 3000

1.500.625 0.307 146 365 730 1460 2190 2920 43801.000 0.785 98 245 491 982 1473 1964 2946

2.001.000 0.785 236 589 1178 2355 3533 4710 70651.375 1.48 166 414 828 1655 2483 3310 4965

2.501.000 0.785 413 1031 2063 4125 6188 8250 123751.375 1.48 343 856 1713 3425 5138 6850 102751.750 2.41 250 625 1250 2500 3750 5000 7500

3.251.375 1.48 682 1704 3408 6815 10223 13630 204451.750 2.41 589 1473 2945 5890 8835 11780 176702.000 3.14 516 1290 2580 5160 7740 10320 15480

4.001.750 2.41 1016 2540 5080 10160 15240 20320 304802.000 3.14 943 2358 4715 9430 14145 18860 282902.500 4.91 766 1915 3830 7660 11490 15320 22980

5.00

2.000 3.14 1650 4125 8250 16500 24750 33000 495002.500 4.91 1473 3683 7365 14730 22095 29460 441903.000 7.07 1257 3143 6285 12570 18855 25140 377103.500 9.62 1002 2505 5010 10020 15030 20040 30060

6.00

2.500 4.91 2336 5840 11680 23360 35040 46720 700803.000 7.07 2120 5300 10600 21200 31800 42400 636003.500 9.62 1865 4663 9325 18650 27975 37300 559504.000 12.57 1570 3925 7850 15700 23550 31400 47100

7.00

3.000 7.07 3142 7855 15710 31420 47130 62840 942603.500 9.62 2887 7218 14435 28870 43305 57740 866104.000 12.57 2592 6480 12960 25920 38880 51840 777604.500 15.90 2259 5648 11295 22590 33885 45180 677705.000 19.63 1886 4715 9430 18860 28290 37720 56580

8.00

3.500 9.62 4065 10163 20325 40650 60975 81300 1219504.000 12.57 3770 9425 18850 37700 56550 75400 1131004.500 15.90 3437 8593 17185 34370 51555 68740 1031105.000 19.63 3064 7660 15320 30640 45960 61280 919205.500 23.76 2651 6628 13255 26510 39765 53020 79530

WhereF=Forceinpounds. P = Pressure at the cylinder in pounds per square inch, gauge. A = Effective area of cylinder piston in square inches.




61

D

Cylinder Weights

The estimated weights shown below are for standard Series RDH hydraulic cylinders equipped with the different piston rod diameters. To determine the total netweightofacylinder,firstselecttheBasicWeight

Table A–SeriesRDHCylinderWeightsinpounds.

for the proper mount at zero stroke, then calculate the weight of the cylinder stroke and add the result to the BasicWeight.Forextrarodextension,usepistonrodweightperinchshowninTableB.

Table B–Extraweightforlongerthanstandardrodextensions

Cylinder Weights

Bore Ø

Rod No.

MM Rod

Ø

Single Rod Cylinders Add per Inch of StrokeBase Weight at Zero Stroke

T B, BB, SB/SBM, TT DD J/JP H

1.501 0.625 2.5 3.7 5.6 3.8 3.4 0.42 1.000 2.7 3.9 5.8 4.0 3.6 1.0

2.001 1.000 5.0 6.6 9.7 7.3 6.4 0.62 1.375 5.4 7.0 10.1 7.7 6.8 1.7

2.501 1.000 8.8 11.3 13.7 12.5 11.3 0.82 1.750 9.4 11.9 14.3 13.2 12.0 2.73 1.375 9.8 12.3 14.7 13.6 12.3 2.4

3.251 1.375 16.5 22.5 24.9 23.6 21.7 1.42 2.000 17.2 23.2 25.6 24.2 22.4 4.23 1.750 17.8 23.8 26.2 24.8 23.0 4.0

4.001 1.750 22.3 28.3 31.4 34.4 31.4 1.82 2.500 24.0 30.0 33.1 36.1 33.1 6.13 2.000 24.7 30.7 33.8 36.7 33.8 5.6

5.00

1 2.000 51.2 57.2 67.7 69.8 66.0 2.72 3.500 52.9 58.9 69.4 71.5 67.7 10.13 2.500 54.6 60.6 71.1 73.2 69.4 8.74 3.000 56.8 62.8 73.3 75.4 71.6 9.3

6.00

1 2.500 75.7 83.7 102.8 106.5 100.9 4.32 4.000 79.7 87.7 106.8 110.5 104.9 14.43 3.000 81.9 89.9 109.0 112.7 107.2 12.94 3.500 83.6 91.6 110.7 114.4 108.8 13.6

7.00

1 3.000 111.8 124.8 154.0 151.8 141.7 5.32 5.000 116.1 129.1 158.3 156.1 146.0 19.83 3.500 118.0 131.0 160.2 158.0 147.9 16.94 4.000 122.0 135.0 164.2 162.0 151.9 17.85 4.500 126.1 139.1 168.3 166.1 156.0 18.7

8.00

1 3.500 159.6 173.6 217.4 216.7 204.5 7.52 5.500 166.9 180.9 224.7 224.0 211.8 25.73 4.000 171.4 185.4 229.2 228.5 216.3 22.64 4.500 175.5 189.5 233.3 232.6 220.4 23.55 5.000 179.8 193.8 237.6 236.9 224.7 24.6

Rod Ø

Piston Rod Weight per Inch (lb)

Rod Ø

Piston Rod Weight per Inch (lb)

0.625 0.09 3.000 2.00

1.000 0.22 3.500 2.72

1.375 0.42 4.000 3.56

1.750 0.68 4.500 4.50

2.000 0.89 5.000 5.56

2.500 1.39 5.500 6.72




62

Seal Information

Operating Fluids and Temperature Range Fluidpowercylindersaredesignedforusewithpressurizedair, hydraulic oil and fire resistant fluids; in some cases special seals are required.Standard Seals (class 1) Class 1 seals are what is normally provided in a cylinder unless otherwise specified. They are intended for use with fluids such as: air, nitrogen, mineral base hydraulic oil or MIL-H-5606withinthetemperaturerangeof-10°F(-23°C)to+165°F(+74°C).Theindividualsealsmaybenitrile(Buna-N),enhancedpolyurethane,polymyte,P.T.F.E.orfilledP.T.F.E.Water Base Fluid Seals (class 2) Generallyclass2sealsareintendedforusewithwaterbasefluidswithinthetemperatureof-10°F(-23°C)to+165°F(+74°C)exceptforHighWaterContentFluids(H.W.C.F.)inwhichcaseClass6sealsshouldbeused.Typicalwaterbasefluidsare:Water,Water-Glycol,Water-inEmulsion,Houghto-Safe27,620,5040,MobilPyrogardD,ShellIrus905,UconHydrolubeJ-4.Thesesealsarenitrile.RodsealandpistonsealwillhavepolymyteorP.T.F.E.back-upwasherwhenrequired.PistonsealmaybefilledP.T.F.E.O-ringswillhavenitrileback-upwashers when required.Ethylene Propylene (E.P.R.) Seals (class 3) Class 3 seals are intended for use with some Phosphate Ester Fluidsbetweenthetemperaturesof-10°F(-23°C)to+130°F(+54°C).TypicalfluidscompatiblewithE.P.R.sealsareSkydrol500and700.E.P.R.areEthylenePropylene.RodsealandpistonsealwillhaveaP.T.F.E.back-upwasherwhenrequired.PistonsealmaybefilledP.T.F.E.O-ringswillhaveEPR back-up washers when required. Note: E.P.R. seals are not compatible with mineral base hydraulic oil or greases. Even limited exposure to these fluids will cause severe swelling. P.T.F.E.back-upwashermaynotbesuitablewhenusedinaradiation environment.Low Temperature Nitrile Seals (class 4) Class4sealsareintendedforlowtemperatureservicewith the same type of fluids as used with Class 1 seals within the temperaturerangeof-50°F(-46°C)to+150°F(+66°C).Rodsealandpistonsealwillhaveleather,polymyteorP.T.F.E.back-up washers when required. Piston seal may be filled P.T.F.E.O-ringswillhavenitrileback-upwasherswhenrequired.Note:CertainfluidsmayreactadverselywithClass4seals compared to Class 1 seals.Fluorocarbon Seals (class 5) Class5sealsareintendedforelevatedtemperatureserviceorforsomePhosphateEsterFluidssuchasHoughto-Safe1010,1055,1120;Fyrquel150,220,300,350;MobilePyrogard42,43,53,and55.Note:Inaddition,class5sealscanbeusedwith fluids listed on the next page under standard service. However,theyarenotcompatiblewithPhosphateEsterFluidssuchasSkydrols.Class5sealscanoperatewithatempera-turerangeof-10°F(-23°C)to+250°F(+121°C).Class5sealsmaybeoperatedto+400°F(+204°C)withlimitedservicelife.Fortemperaturesabove+250°F(+120°C)thecylindermustbemanufactured with non-studded piston rod and thread and a pinnedpistontorodconnection.Class5rodsealandpistonsealwillhaveP.T.F.E.back-upwasherswhenrequired.PistonsealmaybefilledP.T.F.E.O-ringswillhavefluorocarbonback-up when required.H.W.C.F. Seals (class 6) Class6sealsareintendedforHighWaterContentFluids(H.W.C.F.)suchasHoughton,Hydrolubric120BandSonsol Lubrizolwithinthetemperaturerangeof+40°F(+4°C)to+120°F(+49°C).Class6sealsarethesameasClass2seals.RodsealandpistonsealwillhaveP.T.F.E.andorpolymyteback-up washers when required. Piston seal may be filled P.T.F.E.O-ringswillhavenitrileback-upwasherswhenrequired. Energized PTFE Seals (class 8) Class8sealsconsistofPTFErodseals,rodwipersealandpiston seal. All seals have o-ring energizers for sealing in static

and dynamic applications. They are intended for high tempera-tureapplications,to400°F(204°C),wherelongerseallifeandimproved high temperature sealing performance is required. Endsealandenergizero-ringsealswillbefluorocarbon.FluidresistanceiscomparabletoClass5.CylindersincorporatingClass 8 Seals will not have studded piston rods.Warning The piston rod stud and the piston rod to piston threaded connections are secured with an anaerobic adhesive which is temperature sensitive. Cylinders are assembled with anaerobic adhesivehavingamaximumtemperatureratingof+250°F(+74°C).Cylindersspecifiedwithallothersealcompounds(builtbefore1997)wereassembledwithanaerobicadhesivehavingamaximumoperatingtemperaturerating+165°F(+74°C).Thesetemperaturelimitationsarenecessarytoprevent the possible loosening of the threaded connections. Cylindersoriginallymanufactured(before1997)withclass1seals (Nitrile) that will be exposed to ambient temperatures above+165°F(+74°C)mustbemodifiedforhighertemperatureservice. Contact the factory immediately and arrange for the piston to rod and the stud to piston rod connections to be properly re-assembled to withstand the higher temperature service. Hi-Load Seals Hi-loadsealsconsistofonePTFEdynamicpistonsealwithan energizer underneath. Hi-load piston arrangement includes a wear ring on the piston. The piston seal is virtually leak-free under static conditions and can tolerate high pres sure. The wear ring on the piston can also tolerate high side loads. The dynamicportionofthesealisbronzefilledPTFEandcompat-ible with all conditions and fluids listed on this page. However, carbonfilledPTFEwillprovidebetterseallifewhenusedwithclass6fluids.AnitrileexpanderwillbeprovidedunlessClass3or5sealsarespecified.Inthosecasestheexpanderwillbeof E.P.R. or fluorocarbon respectively. Note: It may be neces-sarytocyclethepistonseals40or50timesbeforeachievingleakage free performance.Low Friction Hydraulic Seals Lowfrictionhydraulicsealsareavailableasanoption.Theyare sometimes used when a cylinder is controlled by a servo valve or proportional valve. The rod seals, rod wiper seal and piston seal are two-piece assemblies that include a filled PTFEdynamicsealwithano-ringenergizer.ThepistonandheadalsoincludeWearGard™wearrings.ThefilledPTFEseals are compatible with the fluids listed on this page and provide virtually leak-free sealing. The energizers will be fluoro carbon unless E.P.R. seals are specified. In those cases the energizers will be E.P.R. Note: It may be necessary to cycletheseseals40or50timesbeforeachievingleakage free performance.Water Service Series RDH cylinders can be modified to make them more suitable for use with water as the operating medium. The modifications include chrome-plated cylinder bore; electroless nickel-platedhead,capandpiston;andachromeplated17-4stainless steel piston rod. When high water base fluids are the operating medium, hydraulic cylinders are usually supplied with high water base rod wiper and seals. Water and high water base fluid operated cylinders are best used on short stroke applications or where high pressure is applied only to clamp the load.Warranty Parker Hannifin will warrant cylinders modified for water or high water content fluid service to be free of defects in materials or workmanship, but cannot accept responsibility of premature failure due to excessive wear from lack of lubricity or where failure is caused by corrosion, electrolysis or mineral deposits within the cylinder.




63

D

Seal Information

Temperature Range

-10°F(-23°C)to +165°F(+74°C)

-10°F(-23°C)to +165°F(+74°C)

-10°F(-23°C)to +130°F(+54°C)

-50°F(-46°C)to +150°F(+66°C)

See paragraph on FluorocarbonSealson previous page for recommended temperature range.

+40°F(+4°C)to +120°F(+49°C)

-15°F(-26°C)to +400°F(+204°C)

Class No.

1 (Standard) (Nitrile, Polyurethane)

2WaterBaseFluidSeal

3 E.P.R. Note: (E.P.R.) seals are not compatible with Hydraulic Oil4Nitrile

5FluorocarbonSeals Note:FluorocarbonsealsarenotsuitableforusewithSkydrolfluid,butcanbeusedwithhydraulic oil if desired.6HWCF(samesealsasClass2)

8EnergizedPTFE

Typical Fluids

Air, Nitrogen HydraulicOil,Mil-H-5606Oil

Water,Water-Glycol,Water-in-OilEmulsionHoughto-Safe,271,620,5040.MobilPyrogardD,ShellIrus905.UconHydrolubeJ-4

SomePhosphateEsterFluids Skydrol500,7000

LowTemperatureAirorHydraulicOil

High Temperature Houghto-Safe1010,1055,1120 Fyrquel150,220,300,550 MobilPyrogard42,43,53,55

Houghton,Hydrolubric120B SonsolLubrizol;forotherHWCF— consult factory.

SeeClass5Seals

Fluids and Temperature Range

Seal Compounds by Seal CodeSeal Code

Description Rod Wiper Seal

Rod Seal Rod Seal Backup

Ring

Piston Seal

Piston Seal

Energizer

Piston Joint Seal

End Seal End Seal Backup

Ring

Wear Rings

(blank) Standard (Class 1) Urethane Polyurethane N/A Polyure-

thane Nitrile Fluoro-carbon Nitrile Nitrile Composite

2WaterBase Fluid/HWCF

(Classes 2and6)

Nitrile Carboxilated Nitrile PTFE

BronzeFilledPTFE

Nitrile Fluoro-carbon Nitrile Nitrile Composite

X EPR (Class 3) EPR EPR PTFEBronzeFilledPTFE

EPR EPR EPR PTFE Composite

4Low

Temper ature (Class4)

Urethane Polyurethane N/A Polyure-thane

Low Temper-

ature Nitrile

Fluoro-carbon

Low Temper-

ature Nitrile

Low Temper-

ature Nitrile

Composite

V Fluorocarbon (Class5) Fluorocarbon Fluorocarbon PTFE

BronzeFilledPTFE

Fluoro-carbon

Fluoro-carbon

Fluoro-carbon

Fluoro-carbon Composite

HExtreme High Temper ature

(Class 8)

BronzeFilledPTFEwithFluorocarbon

Energizer

BronzeFilledPTFEwithFluorocarbon

EnergizerN/A

BronzeFilledPTFE

Fluoro-carbon

Fluoro-carbon

Fluoro-carbon

Fluoro-carbon

High Temper-

ature Composite

KStandard

(withBronzeFilledPTFE Piston Seal)

Urethane Polyurethane N/ABronzeFilledPTFE

Nitrile Fluoro-carbon Nitrile Nitrile Composite

EFluorocarbon

Rod Seals Only

Fluorocarbon Fluorocarbon PTFE Polyure-thane Nitrile Fluoro-

carbon Nitrile Nitrile Composite

MMetallic

Rod Wiper, Standard

Seals

BrasswithFluorocarbon

EnergizerPolyurethane N/A Polyure-

thane Nitrile Fluoro-carbon Nitrile Nitrile Composite

DMetallicRodWiper,Fluoro-carbon Seals

BrasswithFluorocarbon

EnergizerFluorocarbon PTFE

BronzeFilledPTFE

Fluoro-carbon

Fluoro-carbon

Fluoro-carbon

Fluoro-carbon Composite




64

Ports

PortsSeries RDH cylinders can be supplied with many port styles, but SAE straight o-ring ports are standard. Extra ports are available for an additional charge.

Standard port location is position 1 as shown in the mountingdrawingsandFigure1below.Portlocationsother than position 1 can be specified for no additional charge if both ports are in the same new position. If either port is required to be at a different position than the other, additional charges would apply.

Figure 1

Head (Rod) End Head Cap

Straight Thread PortsThe SAE straight thread o-ring port is recommended for hydraulic applications. SAE port size numbers are listednexttotheNPTFpipethreadcounterpartsforeach bore size in the respective catalog pages. Size number, tube O.D., and port thread size for SAE ports are listed in Table A.

Table ASAE Straight Thread O-Ring Ports

Note:Forthepressureratingsofindividualconnectors, contact your connector supplier. Hydraulic cylinders applied with meter out or deceleration circuits are subject to intensified pressure at the cylinder piston rod end. The rod end pressure is approximately equal to:

Effective Cap End Piston Area Effective Rod End Piston Area

x Operating Pressure

International PortsOther port configurations to meet international require-ments are available for an additional charge. Series RDH cylinderscanbesuppliedwithBritishstandardtaperports(BSPT).Suchporthasataperof1in16measuredon the diameter (1/16"perinch).Thethreadformis Whitworth System, and size and number of threads per inch are as follows:

Table BBritishStandardPipeThreads

BritishstandardparallelinternalthreadsaredesignatedasBSPPandhavethesamethreadformandnumberofthreadsperinchastheBSPTtypeandcanbesuppliedfor an additional charge. Unless otherwise specified, theBSPPorBSPTportsizesuppliedwillbethesamenominalpipesizeastheNPTFportforagivenboresizecylinder.

1

2

3

4

Size No.

Tube O.D. (in.)

Thread Size

2 0.13 5/16-243 0.19 3/8-244 0.25 7/16-205 0.31 1/2 - 206 0.38 9/16-188 0.50 3/4-16

10 0.63 7/8-1412 0.75 11/16-1216 1.00 15/16-1220 1.25 15/8-1224 1.50 17/8-1232 2.00 2 1/2 - 12

NominalPipe Size

No. ThreadsPer Inch

PipeO.D.

1/8 28 0.3831/4 19 0.5183/8 19 0.6561/2 14 0.8253/4 14 1.0411 11 1.309

11/4 11 1.6501 1/2 11 1.882

2 11 2.347




65

D

Table C – Standard Port Sizes

Undersize and Oversize PortsUndersize and oversize ports are available. Please consult factory. Metricportscanalsobesuppliedtoorderforan additional charge. See table below for the standard port size for each bore.

Bore Ø

U NPTF

T SAE

R BSPP

B BSPT

G Metric

P Flange

1.50 3/8 6 G3/8 Rc3/8 M18x1.5 NA2.00 1/2 8 G1/2 Rc1/2 M22x1.5 82.50 1/2 8 G1/2 Rc1/2 M22x1.5 93.25 3/4 12 G3/4 Rc3/4 M27x2 124.00 3/4 12 G3/4 Rc3/4 M27x2 125.00 3/4 12 G3/4 Rc3/4 M27x2 126.00 1 16 G1 Rc1 M33x2 167.00 11/4 20 G1-1/4 Rc1-1/4 M42x2 208.00 11/4 20 G1-1/4 Rc1-1/4 M42x2 24

Ports

SAE 4-Bolt Flange Ports (Code 61, 3000 psi)SAE4-boltflangeportconnectionsprovidetheabilitytoconnect larger pipe or hose sizes and achieve higher-pressure capability at reasonable assembly torques. Becauseofthelowerassemblytorquescomparedtoanequivalentsizethreadedport,SAE4-boltflangeports are well suited for tight quarters where wrench clearances are limited. See Table A for port mounting flangedimensionsandTableBforportflangeheightdimensions.

F

HDA

GG

BQ

ØEE 4X Z Thread

Flange Size

SAE Dash No.

A B GG Q F EE Ø

Z

0.50 8 1.81 2.13 0.69 1.50 0.63 0.548 5/16-180.75 12 1.97 2.56 0.88 1.88 0.71 0.744 3/8-161.00 16 2.17 2.75 1.03 2.06 0.71 0.959 3/8-161.25 20 2.68 3.12 1.19 2.31 0.83 1.280 7/16-141.50 24 3.07 3.68 1.41 2.75 0.98 1.502 1/2-13

Table ABore

ØHD

Code 61 Flange Size

0.50 0.75 1.00 1.25 1.501.50 N/A N/A N/A N/A N/A2.00 2.52 N/A N/A N/A N/A2.50 2.85 N/A N/A N/A N/A3.25 3.29 3.29 3.37 N/A N/A4.00 3.65 3.65 3.73 N/A N/A5.00 4.23 4.23 4.31 N/A N/A6.00 4.85 4.85 4.93 5.04 N/A7.00 5.35 5.35 5.43 5.54 5.668.00 5.98 5.98 6.06 6.17 6.29

Table B




66

Stroke Data and Mounting Groups

Stroke DataSeries RDH cylinders are available in any practical stroke length.

Stroke Length ToleranceStroke length tolerances are required due to buildup of tolerances of the piston, head, cap and cylinder tube.

Standard stroke length tolerances are:

forstrokesupto43"=-0/+.040"

forstrokesgreaterthan43"=-0/+.062"

Forclosertolerancesonstrokelength,itisnecessaryto specify the required tolerance plus the pressure and temperature at which the cylinder will operate. Stroke tolerancessmallerthan.015"arenotgenerallypracticaldue to elasticity of cylinders. If machine design requires such close tolerances, use of a stroke adjuster or special endcap ties may achieve the desired result. Please consult factory.

Mounting GroupsStandard mountings for Series RDH cylinders fall into two basic groups. The groups can be summarized as follows:

The cylinder’s mounting directly affects the maximum pressure at which the cylinder can be used. Stroke length, piston rod connection to load, extra piston rod length over standard, etc. should be considered for thrust loads. See Stop Tubing and Piston Rod Selection

Data on the following pages to first determine whether stop tubing is recommended and then determine the correct piston rod diameter for an application. Alloy steel mounting bolts are recommended for all mounting styles.

Style HStyles J/JP

Style B Style BB

Straight Line Force Transfer–fixedmountswhich absorb force on the cylinder centerline

Pivot Force Transfer–mountingsthatpermita cylinder to change its alignment in one plane

Style SB/SBM Style TT Style DD

Fatigue LifeAlthough each application is unique, all cylinders have a finite life. In general, welded cylinders have a limited fatigue life when used at the maximum pressure rating. Series RDH cylinders are rated for industrial-grade service but for the maximum possible fatigue life in severe duty applications, Parker cylinders with another construction style (tie-rod, mill-type or bolted) should be considered. If necessary, consult the factory forassistanceorreviewBulletinHY08-1320-T1.

Note: User Responsibility. The user, through its own analysis and testing, is solely responsible for making the final selection of the system and Product and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application and follow applicable industry standards and Product information. If Seller provides Product or system options, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the Products or systems.




67

D

L

Stop Tubing

Stop TubingStop tube is recommended to lengthen the distance between the rod bearing and piston bearing to reduce bearing loads on long push stroke cylinders when the cylinder is fully extended. This is especially true of horizontally mounted cylinders. As part of the piston assembly and positioned between the piston and head, a stop tube restricts the extended position of the rod using the increased distance to achieve additional stability.

Use the following steps to determine the need for stop tube and, if required, how long it should be.1. Examine the groups of cylinder illustrations below

and determine which mounting and rod guiding group type match the required cylinder application.

2.EstablishtheBasicLength(L),withthepistonrodfully extended, for the selected illustration by using the dimensional tables on previous pages of this catalog.Forpivotmountedcylinders,thepin-to-pindimension with the piston rod fully extended must be used. Regardless of mounting style, be sure to include any extended piston rod length beyond the catalog standard.

3. In the Stop Tube Table select the column for the appropriate mounting style and rod end guiding type. IntheBasicLength(L)column,findtherowwiththe range that includes the value calculated in Step 2. The next respective column to the right has the required length of stop tube.

Note:MountingStylesB,BB,SB/SBM,TTandHthatare mounted horizontally should also be checked for turning moments and loads between the rod bearing and piston to ensure they are not excessive. Weight of oil must be included in determining bearing loads.When specifying cylinders with stop tube be sure to call out the net stroke and the length of the stop tube. Machinedesigncanbecontinuedwithoutdelaybylaying in a cylinder equivalent in length to the NET STROKEPLUSSTOPTUBELENGTH,whichisreferredtoasGROSSSTROKE.

Cylinder Mounting and Rod Guiding GroupsPivotMount–Pivotedandrigidlyguidedrodend

StylesB,BB, SB/SBMandTT Style DD

FixedMount–Fixedandrigidlyguidedrodend

Styles J/JP Style HFixedMount–Pivotedandrigidlyguidedrodend

Styles J/JP Style HFixedMount–Unguidedrodend

Styles J/JP Style H

L

L L

L

L L

Stop Tube Table

L

Pivot Mounts (B, BB, SB/SBM,

TT and DD)

Fixed Mounts (J/JP and H)

Pivoted and Rigidly Guided Rod End

Fixed and Rigidly Guided Rod End


Unguided Rod End

Basic Length

(L)

Stop Tube

Length

Basic Length

(L)

Stop Tube

Length

Basic Length

(L)

Stop Tube

Length

Basic Length

(L)

Stop Tube

Length0 - 40 0 0 - 80 0 0 - 57 0 0 - 20 041 - 50 1 81 - 100 1 58 - 71 1 21 - 25 151 - 60 2 101 - 120 2 72 - 86 2 26 - 30 261 - 70 3 121 - 140 3 87 - 100 3 31 - 35 371 - 80 4 141 - 160 4 101 - 114 4 36 - 40 481 - 90 5 161 - 180 5 115 - 129 5 41 - 45 591 - 100 6 181 - 200 6 130 - 143 6 46 - 50 6101 - 110 7 201 - 220 7 144 - 157 7 51 - 55 7111 - 120 8 221 - 240 8 158 - 171 8 56 - 60 8121 - 130 9 241 - 260 9 172 - 186 9 61 - 65 9131 - 140 10 261 - 280 10 187 - 200 10 66 - 70 10141 - 150 11 281 - 300 11 201 - 214 11 71 - 75 11151 - 160 12

ConsultFactory

215 - 229 12 76 - 80 12161 - 170 13 230 - 243 13 81 - 85 13171 - 180 14 244 - 257 14 86 - 90 14181 - 190 15 258 - 271 15 91 - 95 15191 - 200 16 272 - 286 16 96 - 100 16201 - 210 17 287 - 300 17 101 - 105 17211 - 220 18

ConsultFactory

106 - 110 18221 - 230 19 111 - 115 19231 - 240 20 116 - 120 20241 - 250 21 121 - 125 21251 - 260 22 126 - 130 22261 - 270 23 131 - 135 23271 - 280 24 136 - 140 24281 - 290 25 141 - 145 25291 - 300 26 146 - 150 26ConsultFactory ConsultFactory

STOP TUBE

GROSS STROKE

NET STROKE STOP TUBELENGTH




68

Piston Rod Selection Data

Piston Rod Diameter SelectionLongstrokecylinders(upto36"grossstrokemaximum)that work on push with the piston rod loaded in compression should be checked, using the following steps, to ensure an appropriate piston rod diameter is specified.1. First,determinewhetherstoptubingisrequiredas

described on the previous page. 2.UsetheBasicLength(L)thatwasestablishedfor

determining the stop tube length and then add the requiredstoptubelengthtotheBasicLengthtoobtainanAdjustedBasicLength(LA).

3. In the table below, for the mounting style and rod end guiding condition that will be used, find the row for theBoreandRodcombinationthatisrequired.

4.FollowtheBoreandRodrowtotherightandfindthe Operating Pressure column that is closest, but exceeds the system pressure. The intersection of the BoreandRodrowandOperatingPressurecolumndisplaysthemaximumallowableLA.IfLA in the table isgreaterthanorequaltothecalculatedLA, the rod diameter selected is satisfactory for the application.

5. IfLA in the table is less than the calculated Adjusted BasicLengthmovedownthecolumntoaroddiam-eterwithanLA that exceeds the requirement.

6. IftheLA specifies a rod diameter in a larger bore then restart the process of sizing the stop tube and re-checktheroddiameter.ContactthefactoryifLA exceeds 300 inches.

Maximum Basic Lengths (LA) (all dimensions in inches)

1MaximumoperatingpressureislimitedfortheSBMount.PleaserefertomaximumoperatingpressureperboreinSBPressureRatingstableonpage14.

Note: Data in these tables assume standard rod exten-sion (W dimension) and standard rod end accessories. If different, consult factory.

Bore Ø

Rod Ø

Rear Pivot Mounts (B, BB, SB1, SBM and TT)

Front Fixed Mount (J/JP)




Unguided Rod End

Max.AllowableBasic Length(LA) at psi:




500 1000 1500 2000 2500 3000 500 1000 1500 2000 2500 3000 500 1000 1500 2000 2500 3000 500 1000 1500 2000 2500 3000

1.500.625 35 25 20 18 16 14 50 35 29 25 22 20 36 25 21 18 16 15 13 9 7 6 6 51.000 85 60 49 42 38 35 128 91 74 64 57 52 92 65 53 46 41 37 32 23 19 16 14 13

2.001.000 66 47 38 33 29 27 96 68 56 48 43 39 69 49 40 34 31 28 24 17 14 12 11 101.375 116 82 67 58 52 47 182 129 105 91 81 74 130 92 75 65 58 53 45 32 26 23 20 19

2.50 1.000 54 38 31 27 24 22 77 54 44 38 34 31 55 39 32 27 25 22 19 14 11 10 9 81.375 99 70 57 49 44 40 146 103 84 73 65 59 104 73 60 52 46 42 36 26 21 18 16 151.750 151 106 87 75 67 61 236 167 136 118 105 96 168 119 97 84 75 69 59 42 34 29 26 24

3.25 1.375 78 55 45 39 35 32 112 79 65 56 50 46 80 57 46 40 36 33 28 20 16 14 13 111.750 123 87 71 62 55 50 181 128 105 91 81 74 130 92 75 65 58 53 45 32 26 23 20 192.000 157 111 90 78 70 64 237 167 137 118 106 97 169 120 98 85 76 69 59 42 34 30 26 24

4.001.750 102 72 59 51 45 41 147 104 85 74 66 60 105 74 61 53 47 43 37 26 21 18 16 152.000 131 92 75 65 58 53 192 136 111 96 86 79 137 97 79 69 61 56 48 34 28 24 22 202.500 194 137 112 97 87 79 300 213 174 150 134 123 215 152 124 107 96 88 75 53 43 38 34 31

5.00

2.000 107 76 62 53 48 44 154 109 89 77 69 63 110 78 63 55 49 45 38 27 22 19 17 162.500 163 115 94 82 73 67 241 170 139 120 108 98 172 121 99 86 77 70 60 43 35 30 27 253.000 226 160 130 113 101 92 300 245 200 173 155 141 247 175 143 124 111 101 87 61 50 43 39 353.500 289 204 167 145 129 118 300 300 272 236 211 192 300 238 194 168 151 137 118 83 68 59 53 48

6.00

2.500 139 98 80 70 62 57 200 142 116 100 90 82 143 101 83 72 64 58 50 35 29 25 22 203.000 197 139 114 98 88 80 289 204 167 144 129 118 206 146 119 103 92 84 72 51 42 36 32 293.500 260 184 150 130 116 106 300 278 227 196 176 160 281 198 162 140 125 115 98 69 57 49 44 404.000 300 231 188 163 146 133 300 300 296 257 229 209 300 259 212 183 164 150 128 91 74 64 57 52

7.00

3.000 171 121 99 85 76 70 247 175 143 124 111 101 177 125 102 88 79 72 62 44 36 31 28 253.500 228 161 132 114 102 93 300 238 194 168 151 137 241 170 139 120 108 98 84 60 49 42 38 344.000 289 204 167 145 129 118 300 300 254 220 197 180 300 222 181 157 140 128 110 78 63 55 49 454.500 300 249 203 176 157 144 300 300 300 278 249 227 300 281 230 199 178 162 139 98 80 70 62 575.000 300 293 239 207 185 169 300 300 300 300 300 281 300 300 283 245 220 200 172 121 99 86 77 70

8.00

3.500 203 144 117 102 91 83 295 208 170 147 132 120 210 149 122 105 94 86 74 52 43 37 33 304.000 261 185 151 131 117 107 300 272 222 192 172 157 275 194 159 137 123 112 96 68 56 48 43 394.500 300 229 187 162 145 132 300 300 281 244 218 199 300 246 201 174 156 142 122 86 70 61 54 505.000 300 274 224 194 174 158 300 300 300 300 269 245 300 300 248 215 192 175 150 106 87 75 67 615.500 300 300 261 226 202 185 300 300 300 300 300 297 300 300 300 260 232 212 182 129 105 91 81 74




69

D

Piston Rod Selection Data

Maximum Basic Lengths (LA) (all dimensions in inches)Bore

ØRod

ØIntermediate Pivot Mount

(DD)Rear Fixed Mount (H)




Unguided Rod End





500 1000 1500 2000 2500 3000 500 1000 1500 2000 2500 3000 500 1000 1500 2000 2500 3000 500 1000 1500 2000 2500 3000

1.500.625 25 18 14 12 11 10 70 50 40 35 31 29 50 35 29 25 22 20 18 12 10 9 8 71.000 63 44 36 31 28 25 170 120 98 85 76 69 121 86 70 61 54 50 42 30 25 21 19 17

2.001.000 47 33 27 23 21 19 132 93 76 66 59 54 94 67 54 47 42 38 33 23 19 16 15 131.375 90 63 52 44 40 36 232 164 134 116 104 95 166 117 96 83 74 68 58 41 33 29 26 24

2.501.000 38 26 21 18 16 15 107 76 62 54 48 44 77 54 44 38 34 31 27 19 16 13 12 111.375 72 50 41 35 32 29 197 140 114 99 88 81 141 100 81 70 63 58 49 35 28 25 22 201.750 117 82 67 58 51 47 300 213 174 151 135 123 215 152 124 108 96 88 75 53 43 38 34 31

3.251.375 55 39 31 27 24 22 156 110 90 78 70 64 111 79 64 56 50 45 39 28 22 19 17 161.750 90 63 51 44 39 36 246 174 142 123 110 100 176 124 102 88 79 72 62 44 36 31 28 252.000 117 82 67 58 52 47 300 221 181 157 140 128 224 158 129 112 100 91 78 55 45 39 35 32

4.001.750 73 51 42 36 32 29 203 144 117 102 91 83 145 103 84 73 65 59 51 36 29 25 23 212.000 95 67 54 47 42 38 261 185 151 131 117 107 187 132 108 93 83 76 65 46 38 33 29 272.500 149 105 85 74 66 60 300 274 224 194 173 158 277 196 160 138 124 113 97 69 56 48 43 40

5.00

2.000 76 53 43 37 33 30 214 151 123 107 96 87 153 108 88 76 68 62 53 38 31 27 24 222.500 119 84 68 59 52 48 300 231 188 163 146 133 233 165 135 117 104 95 82 58 47 41 36 333.000 172 121 99 85 76 69 300 300 261 226 202 184 300 228 186 161 144 132 113 80 65 56 50 463.500 234 165 135 116 104 95 300 300 300 289 259 236 300 292 239 207 185 169 145 102 83 72 65 59

6.00

2.500 99 70 57 49 44 40 278 197 161 139 124 114 199 141 115 99 89 81 70 49 40 35 31 283.000 143 101 82 71 63 58 300 278 227 197 176 161 281 199 162 140 126 115 98 70 57 49 44 403.500 195 138 112 97 87 79 300 300 300 260 233 212 300 263 215 186 166 152 130 92 75 65 58 534.000 255 180 147 127 113 103 300 300 300 300 292 266 300 300 269 233 208 190 163 115 94 82 73 67

7.00

3.000 121 85 69 60 53 48 300 241 197 171 153 139 244 172 141 122 109 100 85 60 49 43 38 353.500 166 117 95 82 73 66 300 300 263 228 204 186 300 230 188 163 146 133 114 81 66 57 51 464.000 218 153 125 108 96 88 300 300 300 289 259 236 300 292 239 207 185 169 145 102 83 72 65 594.500 276 195 158 137 122 111 300 300 300 300 300 288 300 300 290 252 225 205 176 124 102 88 79 725.000 300 241 196 170 151 138 300 300 300 300 300 300 300 300 300 296 264 241 207 146 119 103 93 84

8.00

3.500 145 102 83 71 64 58 300 288 235 203 182 166 291 205 168 145 130 119 102 72 59 51 45 424.000 190 134 109 94 84 76 300 300 300 261 234 213 300 264 216 187 167 152 131 92 75 65 58 534.500 241 170 138 120 107 97 300 300 300 300 290 264 300 300 267 231 207 189 162 114 93 81 72 665.000 298 210 171 148 132 120 300 300 300 300 300 300 300 300 300 277 248 226 194 137 112 97 87 795.500 300 255 208 180 160 146 300 300 300 300 300 300 300 300 300 300 289 264 226 160 131 113 101 92




70

Cylinder Safety Guide

BeforeselectingorusingParkerHannifinCorporation(theCompany)cylindersor related accessories, it is important that you read, understand and follow the following safety information. Training is advised before selecting and using the Company’s products.

1.0 General Instructions 1.1 Scope–Thissafetyguideprovidesinstructionsforselectingandusing

(including assembling, installing, and maintaining) cylinder products. This safety guide is a supplement to and is to be used with the specific Company publications for the specific cylinder products that are being considered for use.

1.2 Fail Safe–Cylinderproductscananddofailwithoutwarningformanyreasons. All systems and equipment should be designed in a fail-safe mode so that if the failure of a cylinder product occurs people and property won’t be endangered.

1.3 Distribution–Provideafreecopyofthissafetyguidetoeachpersonresponsible for selecting or using cylinder products. Do not select or use the Company’s cylinders without thoroughly reading and understanding this safety guide as well as the specific Company publications for the products considered or selected.

1.4 User Responsibility–Duetoverywidevarietyofcylinderapplicationsand cylinder operating conditions, the Company does not warrant that any particular cylinder is suitable for any specific application. This safety guide does not analyze all technical parameters that must be considered in select-ing a product. The hydraulic and pneumatic cylinders outlined in this catalog are designed to the Company’s design guidelines and do not necessarily meetthedesignguidelineofotheragenciessuchasAmericanBureauofShipping,ASMEPressureVesselCodeetc.Theuser,throughitsown analysis and testing, is solely responsible for:

• Makingthefinalselectionofthecylindersandrelatedaccessories. •Determiningifthecylindersarerequiredtomeetspecificdesignrequire-

ments as required by the Agency(s) or industry standards covering the design of the user’s equipment.

•Assuringthattheuser’srequirementsaremet,OSHArequirementsaremet, and safety guidelines from the applicable agencies such as but not limited to ANSI are followed and that the use presents no health or safety hazards.

•Providingallappropriatehealthandsafetywarningsontheequipmentonwhich the cylinders are used.

1.5 Additional Questions–CalltheappropriateCompanytechnicalservicedepartment if you have any questions or require any additional information. See the Company publication for the product being considered or used, or call1-847-298-2400,orgotowww.parker.com, for telephone numbers of the appropriate technical service department.

2.0 Cylinder and Accessories Selection 2.1 Seals–Partoftheprocessofselectingacylinderistheselectionof

sealcompounds.Beforemakingthisselection,consultthe“sealinformationpage(s)” of the publication for the series of cylinders of interest.

The application of cylinders may allow fluids such as cutting fluids, wash down fluids etc. to come in contact with the external area of the cylinder. These fluids may attack the piston rod wiper and or the primary seal and must be taken into account when selecting and specifying seal compounds.

Dynamic seals will wear. The rate of wear will depend on many operating factors. Wear can be rapid if a cylinder is mis-aligned or if the cylinder has been improperly serviced. The user must take seal wear into consideration in the application of cylinders.

2.2 Piston Rods–Possibleconsequencesofpistonrodfailureor separation of the piston rod from the piston include, but are not limited to are:

•Pistonrodandorattachedloadthrownoffathighspeed. •Highvelocityfluiddischarge. •Pistonrodextendingwhenpressureisappliedinthepiston

retract mode.

Piston rods or machine members attached to the piston rod may move suddenly and without warning as a consequence of other conditions occurring to the machine such as, but not limited to:

•Unexpecteddetachmentofthemachinememberfromthepistonrod.

•Failureofthepressurizedfluiddeliverysystem(hoses,fittings,valves,pumps, compressors) which maintain cylinder position.

•Catastrophiccylindersealfailureleadingtosuddenlossofpressurizedfluid.

•Failureofthemachinecontrolsystem. Followtherecommendationsofthe“PistonRodSelectionChartandData”

in the publication for the series of cylinders of interest. The suggested piston rod diameter in these charts must be followed in order to avoid piston rod buckling.

Piston rods are not normally designed to absorb bending moments or loads which are perpendicular to the axis of piston rod motion. These additional loads can cause the piston rod to fail. If these types of additional loads are expected to be imposed on the piston rod, their magnitude should be made known to our engineering department.

The cylinder user should always make sure that the piston rod is securely attached to the machine member.

On occasion cylinders are ordered with double rods (a piston rod extended from both ends of the cylinder). In some cases a stop is threaded on to one of the piston rods and used as an external stroke adjuster. On occasions spacers are attached to the machine member connected to the piston rod and also used as a stroke adjuster. In both cases the stops will create a pinch point and the user should consider appropriate use of guards. If these external stops are not perpendicular to the mating contact surface, or if debris is trapped between the contact surfaces, a bending moment will be placed on the piston rod, which can lead to piston rod failure. An external stop will also negate the effect of cushioning and will subject the piston rod to impact loading. Those two (2) conditions can cause piston rod failure. Internal stroke adjusters are available with and without cushions. The use of external stroke adjusters should be reviewed with our engineering department.

The piston rod to piston and the stud to piston rod threaded connections are secured with an anaerobic adhesive. The strength of the adhesive decreases with increasing temperature. Cylinders which can be exposed to tempera-turesabove+250°F(+121°C)aretobeorderedwithanonstuddedpistonrod and a pinned piston to rod joint.

2.3 Cushions–Cushionsshouldbeconsideredforcylinderapplicationswhenthepistonvelocityisexpectedtobeover4inches/second.

Cylinder cushions are normally designed to absorb the energy of a linear applied load. A rotating mass has considerably more energy than the same mass moving in a linear mode. Cushioning for a rotating mass application should be reviewed by our engineering department.

2.4 Cylinder Mountings–Somecylindermountingconfigurationsmayhavecertain limitations such as but not limited to minimum stroke for side or foot mounting cylinders or pressure de-ratings for certain mounts. Carefully review the catalog for these types of restrictions.

Always mount cylinders using the largest possible high tensile alloy steel socket head cap screws that can fit in the cylinder mounting holes and torque them to the manufacturer’s recommendations for their size.

2.5 Port Fittings–Hydrauliccylindersappliedwithmeteroutordecelera-tion circuits are subject to intensified pressure at piston rod end.

The rod end pressure is approximately equal to:

operating pressure x effective cap end area effective rod end piston area

Contact your connector supplier for the pressure rating of individual connectors.

3.0 Cylinder and Accessories Installation and Mounting 3.1 Installation 3.1.1 –Cleanlinessisanimportantconsideration,andcylindersare

shipped with the ports plugged to protect them from contaminants enter-ing the ports. These plugs should not be removed until the piping is to beinstalled.Beforemakingtheconnectiontothecylinderports,pipingshould be thoroughly cleaned to remove all chips or burrs which might have resulted from threading or flaring operations.

Safety Guide for Selecting and Using Hydraulic, Pneumatic Cylinders and Their Accessories

WARNING: FAILURE OF THE CYLINDER, ITS PARTS, ITS MOUNTING, ITS CONNECTIONS TO OTHER OBJECTS, OR ITS CONTROLS CAN RESULT IN: •Unanticipatedoruncontrolledmovementofthecylinderorobjectsconnectedtoit. •Fallingofthecylinderorobjectsheldupbyit. •Fluidescapingfromthecylinder,potentiallyathighvelocity.THESE EVENTS COULD CAUSE DEATH OR PERSONAL INJURY BY, FOR EXAMPLE, PERSONS FALLING FROM HIGH LOCATIONS, BEING CRUSHED OR STRUCK BY HEAVY OR FAST MOVING OBJECTS, BEING PUSHED INTO DANGEROUS EQUIPMENT OR SITUATIONS, OR SLIPPING ON ESCAPED FLUID.




71

D

Cylinder Safety Guide

3.1.2 –Cylindersoperatinginanenvironmentwhereairdryingmaterialsare present such as fast-drying chemicals, paint, or weld splatter, or other hazardous conditions such as excessive heat, should have shields installed to prevent damage to the piston rod and piston rod seals.

3.1.3 –Properalignmentofthecylinderpistonrodanditsmatingcomponent on the machine should be checked in both the extended and retracted positions. Improper alignment will result in excessive rod gland and/or cylinder bore wear. On fixed mounting cylinders attaching the pis-ton rod while the rod is retracted will help in achieving proper alignment.

3.1.4 –Sometimesitmaybenecessarytorotatethepistonrodinorderto thread the piston rod into the machine member. This operation must always be done with zero pressure being applied to either side of the piston.Failuretofollowthisproceduremayresultinlooseningthepistonto rod-threaded connection. In some rare cases the turning of the piston rod may rotate a threaded head and loosen it from the cylinder body. Confirm that this condition is not occurring. If it does, re-tighten the head firmly against the cylinder body.

Fordoublerodcylindersitisalsoimportantthatwhenattachingordetaching the piston rod from the machine member that the torque be applied to the piston rod end of the cylinder that is directly attaching to the machine member with the opposite end unrestrained. If the design of the machine is such that only the rod end of the cylinder opposite to where the rod attaches to the machine member can be rotated, consult the factory for further instructions.

3.2 Mounting Recommendations 3.2.1 –Alwaysmountcylindersusingthelargestpossiblehightensile

alloy steel socket head screws that can fit in the cylinder mounting holes and torque them to the manufacturer’s recommendations for their size.

3.2.2 –Side-MountedCylinders–Inadditiontothemountingbolts,cylinders of this type should be equipped with thrust keys or dowel pins located so as to resist the major load.

3.2.3 –TieRodMounting–Cylinderswithtierodmountingsarerecom-mended for applications where mounting space is limited. Nuts used for this mounting style should be torqued to the same value as the tie rods for that bore size.

3.2.4 –FlangeMountCylinders–Thecontrolleddiameteroftherodgland extension on head end flange mount cylinders can be used as a pilot to locate the cylinders in relation to the machine. After align-ment has been obtained, the flanges may be drilled for pins or dowels to prevent shifting.

3.2.5 –TrunnionMountings–Cylindersrequirelubricatedbearingblockswithminimumbearingclearances.Bearingblocksshouldbecarefullyaligned and rigidly mounted so the trunnions will not be subjected to bending moments. The rod end should also be pivoted with the pivot pin in line and parallel to axis of the trunnion pins.

3.2.6 –ClevisMountings–Cylindersshouldbepivotedatbothendswith centerline of pins parallel to each other. After cylinder is mounted, be sure to check to assure that the cylinder is free to swing through its working arc without interference from other machine parts.

4.0 Cylinder and Accessories Maintenance, Troubleshooting and Replacement

4.1 Storage–Attimescylindersaredeliveredbeforeacustomerisreadytoinstall them and must be stored for a period of time. When storage is required the following procedures are recommended.

4.1.1 –Storethecylindersinanindoorareawhichhasadry,cleanandnoncorrosive atmosphere. Take care to protect the cylinder from both internal corrosion and external damage.

4.1.2 –Wheneverpossiblecylindersshouldbestoredinaverticalposi-tion (piston rod up). This will minimize corrosion due to possible conden-sation which could occur inside the cylinder. This will also minimize seal damage.

4.1.3 –Portprotectorplugsshouldbeleftinthecylinderuntilthetimeofinstallation.

4.1.4 –Ifacylinderisstoredfullofhydraulicfluid,expansionofthefluiddue to temperature changes must be considered. Installing a check valve with free flow out of the cylinder is one method.

4.1.5 –Whencylindersaremountedonequipmentthatisstoredoutsidefor extended periods, exposed unpainted surfaces, e.g. piston rod, must be coated with a rust-inhibiting compound to prevent corrosion.

4.2 Cylinder Trouble Shooting

4.2.1 –External Leakage 4.2.1.1 –Rodsealleakagecangenerallybetracedtowornor

damaged seals. Examine the piston rod for dents, gouges or score marks, and replace piston rod if surface is rough.

Rod seal leakage could also be traced to bearing wear. If clear-ance is excessive, replace rod bearing and seal. Rod seal leakage can also be traced to seal deterioration. If seals are soft or gummy or brittle, check compatibility of seal material with lubricant used if air cylinder, or operating fluid if hydraulic cylinder. Replace with seal material, which is compatible with these fluids. If the seals are hard or have lost elasticity, it is usually due to exposure to tem-peraturesinexcessof165°F.(+74°C).Shieldthecylinderfromtheheatsourcetolimittemperatureto350°F.(+177°C.)andreplacewith fluorocarbon seals.

4.2.1.2 –Cylinderbodysealleakcangenerallybetracedtoaloose head. Torque the head to manufacturer’s recommendation for that bore size.

Excessive pressure can also result in cylinder body seal leak. Determine maximum pressure to rated limits. Replace seals and retorque head as in paragraph above. Excessive pressure can also result in cylinder body seal leak. Determine if the pressure rating of the cylinder has been exceeded. If so, bring the operating pressure down to the rating of the cylinder and have the head replaced.

Pinched or extruded cylinder body seal will also result in a leak. Replace cylinder body seal and retorque as in paragraph above.

Cylinder body seal leakage due to loss of radial squeeze which shows up in the form of flat spots or due to wear on the O.D. or I.D. –Eitherofthesearesymptomsofnormalwearduetohighcyclerate or length of service. Replace seals as per paragraph above.

4.2.2 –Internal Leakage 4.2.2.1 –Pistonsealleak(by-pass)1to3cubicinchesperminute

leakageisconsiderednormalforpistonringconstruction.Virtuallyno static leak with lipseal type seals on piston should be expected. Piston seal wear is a usual cause of piston seal leakage. Replace seals as required.

4.2.2.2 –Withlipsealtypepistonsealsexcessivebackpressuredue to over-adjustment of speed control valves could be a direct cause of rapid seal wear. Contamination in a hydraulic system can result in a scored cylinder bore, resulting in rapid seal wear. In either case, replace piston seals as required.

4.2.2.3 –Whatappearstobepistonsealleak,evidencedbythefact that the cylinder drifts, is not always traceable to the piston. To make sure, it is suggested that one side of the cylinder piston be pressurized and the fluid line at the opposite port be disconnected. Observe leakage. If none is evident, seek the cause of cylinder drift in other component parts in the circuit.

4.2.3 –Cylinder Fails to Move the Load 4.2.3.1 –Pneumaticorhydraulicpressureistoolow.Checkthe

pressure at the cylinder to make sure it is to circuit requirements. 4.2.3.2 –PistonSealLeak–Operatethevalvetocyclethecylinder

and observe fluid flow at valve exhaust ports at end of cylinder stroke. Replace piston seals if flow is excessive.

4.2.3.3 –Cylinderisundersizedfortheload–Replacecylinderwithone of a larger bore size.

4.3 Erratic or Chatter Operation 4.3.1 –Excessivefrictionatrodbearingorpistonbearingduetoload

misalignment–Correctcylinder-to-loadalignment. 4.3.2 –Cylindersizedtooclosetoloadrequirements–Reduceloador

install larger cylinder. 4.3.3 –Erraticoperationcouldbetracedtothedifferencebetweenstatic

and kinetic friction. Install speed control valves to provide a back pres-sure to control the stroke.

4.4 Cylinder Modifications, Repairs, or Failed Component–Cylinders as shipped from the factory are not to be disassembled and or modified. If cylinders require modifications, these modifications must be done at company locations or by the Company’s certified facilities. The Industrial Cylinder Division Engineering Department must be notified in the event of a mechanical fracture or permanent deformation of any cylinder component (excluding seals). This includes a broken piston rod, head, mounting accessory or any other cylinder component. The notification should include all operation and application details. This information will be used to provide an engineered repair that will prevent recurrence of the failure.

It is allowed to disassemble cylinders for the purpose of replacing seals or seal assemblies. However, this work must be done by strictly following all the instructions provided with the seal kits.




72

Offer of Sale

TheitemsdescribedinthisdocumentandotherdocumentsanddescriptionsprovidedbyParkerHannifinCorporation,HydraulicsGroup,anditsauthorizeddistributors(“Seller”)areherebyofferedforsaleatpricestobeestablishedbySeller.Thisofferanditsacceptancebyanycustomer(“Buyer”)shallbegovernedbyallofthefollowingTermsandConditions.Buyer’sorderforanyitemdescribedinitsdocument,whencommunicatedtoSellerverbally,orinwriting,shallconstituteacceptanceofthisoffer.Allgoodsorworkdescribedwillbe referred to as “Products”.1. Terms and Conditions. Seller’s willingness to offer Products, or accept an order for Products,toorfromBuyerisexpresslyconditionedonBuyer’sassenttotheseTermsand Conditions and to the terms and conditions found on-line at www.parker.com/saleterms/. Sellerobjects toanycontraryoradditional termorconditionofBuyer’sorderoranyotherdocumentissuedbyBuyer.2. Price Adjustments; Payments. Prices stated on the reverse side or preceding pages of this document are valid for 30 days. After 30 days, Seller may change prices to reflect any increase in its costs resulting from state, federal or local legislation, price increases from its suppliers, or any change in the rate, charge, or classification of any carrier. The prices stated on the reverse or preceding pages of this document do not include any sales, use, or other taxes unless so stated specifically. Unless otherwise specifiedbySeller,allpricesareF.O.B.Seller’sfacility,andpaymentisdue30daysfromthedateofinvoice.After30days,Buyershallpayinterestonanyunpaidinvoicesattherateof1.5%permonthorthemaximumallowablerateunderapplicablelaw.3. Delivery Dates; Title and Risk; Shipment. All delivery dates are approximate and Seller shall not be responsible for any damages resulting from any delay. Regardless of the manner of shipment, title to any products and risk of loss or damage shall pass to BuyerupontendertothecarrieratSeller’sfacility(i.e.,whenit’sonthetruck,it’syours).Unless otherwise stated, Seller may exercise its judgment in choosing the carrier and meansofdelivery.NodefermentofshipmentatBuyers’requestbeyondtherespectivedates indicated will be made except on terms that will indemnify, defend and hold Seller harmlessagainstall lossandadditionalexpense.Buyershallberesponsibleforany additional shipping charges incurred by Seller due to Buyer’s changes in shipping, product specifications or in accordance with Section 13, herein.4. Warranty. Seller warrants that the Products sold hereunder shall be free from defects in material or workmanship for a period of eighteen months from the date of delivery to Buyer. The prices charged for Seller’s products are based upon the exclusive limited warranty stated above, and upon the following disclaimer: DISCLAIMER OFWARRANTY: THISWARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO PRODUCTS PROVIDED HEREUNDER. SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS AND IMPLIED, INCLUDINGMERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSE.5. Claims; Commencement of Actions. Buyer shall promptly inspect all Productsupon delivery. No claims for shortages will be allowed unless reported to the Seller within 10 days of delivery. No other claims against Seller will be allowed unless asserted inwritingwithin60daysafterdeliveryor,inthecaseofanallegedbreachofwarranty,within 30 days after the date within the warranty period on which the defect is or should havebeendiscoveredbyBuyer.Anyactionbaseduponbreachofthisagreementorupon any other claim arising out of this sale (other than an action by Seller for any amountdue toSeller fromBuyer)mustbe commencedwithin thirteenmonths fromthe date of tender of delivery by Seller or, for a cause of action based upon an alleged breach of warranty, within thirteen months from the date within the warranty period on whichthedefectisorshouldhavebeendiscoveredbyBuyer.6. LIMITATION OF LIABILITY. UPON NOTIFICATION, SELLER WILL, AT ITS OPTION, REPAIR OR REPLACE A DEFECTIVE PRODUCT, OR REFUND THE PURCHASEPRICE. INNOEVENTSHALLSELLERBE LIABLE TOBUYERFORANYSPECIAL,INDIRECT,INCIDENTALORCONSEQUENTIALDAMAGESARISING OUT OF, OR AS THE RESULT OF, THE SALE, DELIVERY, NON-DELIVERY, SERVICING,USEORLOSSOFUSEOFTHEPRODUCTSORANYPARTTHEREOF, ORFORANYCHARGESOREXPENSESOFANYNATUREINCURREDWITHOUT SELLER’S WRITTEN CONSENT, EVEN IF SELLER HAS BEEN NEGLIGENT,WHETHER IN CONTRACT, TORT OR OTHER LEGAL THEORY. IN NO EVENTSHALLSELLER’SLIABILITYUNDERANYCLAIMMADEBYBUYEREXCEEDTHEPURCHASEPRICEOFTHEPRODUCTS.7. Contingencies. Seller shall not be liable for any default or delay in performance if caused by circumstances beyond the reasonable control of Seller.8. User Responsibility. The user, through its own analysis and testing, is solely responsible for making the final selection of the system and Product and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application and follow applicable industry standards and Product information. If Seller provides Product or system options, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the Products or systems.9. Loss to Buyer’s Property. Any designs, tools, patterns, materials, drawings, confi-dentialinformationorequipmentfurnishedbyBuyeroranyotheritemswhichbecomeBuyer’sproperty,maybeconsideredobsoleteandmaybedestroyedbySelleraftertwoconsecutiveyearshaveelapsedwithoutBuyerplacinganorderfortheitemswhichare manufactured using such property. Seller shall not be responsible for any loss or damage to such property while it is in Seller’s possession or control.10. Special Tooling. A tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired to manufacture Products. Such special tooling shall be and remain Seller’s property notwithstanding payment of any charges by Buyer. In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in the manufacture of the Products, even if such apparatus has been specially converted or adapted for such manufacture and notwithstandinganychargespaidbyBuyer.Unlessotherwiseagreed,Sellershallhavethe right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time.

11. Buyer’s Obligation; Rights of Seller. To secure payment of all sums due or other-wise, Seller shall retain a security interest in the goods delivered and this agreement shallbedeemedaSecurityAgreementunder theUniformCommercialCode.Buyer authorizesSelleras itsattorney toexecuteand fileonBuyer’sbehalfalldocumentsSeller deems necessary to perfect its security interest. Seller shall have a security interestin,andlienupon,anypropertyofBuyerinSeller’spossessionassecurityforthepaymentofanyamountsowedtoSellerbyBuyer.12. Improper Use and Indemnity. Buyer shall indemnify, defend, and hold Sellerharmless from any claim, liability, damages, lawsuits, and costs (including attorney fees), whether for personal injury, property damage, patent, trademark or copyright infringementoranyotherclaim,broughtbyorincurredbyBuyer,Buyer’semployees,or any other person, arising out of: (a) improper selection, improper application or other misuseofProductspurchasedbyBuyerfromSeller;(b)anyactoromission,negligentorotherwise,ofBuyer; (c)Seller’suseofpatterns,plans,drawings,orspecificationsfurnishedbyBuyertomanufactureProduct;or(d)Buyer’sfailuretocomplywiththesetermsandconditions.SellershallnotindemnifyBuyerunderanycircumstanceexceptas otherwise provided.13. Cancellations and Changes. Orders shall not be subject to cancellation or change byBuyerforanyreason,exceptwithSeller’swrittenconsentandupontermsthatwillindemnify, defend and hold Seller harmless against all direct, incidental and consequen-tial loss or damage. Seller may change product features, specifications, designs and availabilitywithnoticetoBuyer.14. Limitation on Assignment. Buyermaynotassignitsrightsorobligationsunderthis agreement without the prior written consent of Seller.15. Entire Agreement. This agreement contains the entire agreement between the BuyerandSellerandconstitutes the final,completeandexclusiveexpressionof theterms of the agreement. All prior or contemporaneous written or oral agreements or negotiations with respect to the subject matter are herein merged. 16. Waiver and Severability. Failure toenforceanyprovisionof thisagreementwillnot waive that provision nor will any such failure prejudice Seller’s right to enforce that provision in the future. Invalidation of any provision of this agreement by legislation or other rule of law shall not invalidate any other provision herein. The remaining provisions of this agreement will remain in full force and effect.17. Termination. This agreement may be terminated by Seller for any reason and at anytimebygivingBuyerthirty(30)dayswrittennoticeoftermination.Inaddition,Sellermaybywrittennoticeimmediatelyterminatethisagreementforthefollowing:(a)Buyercommits a breach of any provision of this agreement (b) the appointment of a trustee, receiverorcustodianforalloranypartofBuyer’sproperty(c)thefilingofapetitionforrelief in bankruptcy of the other Party on its own behalf, or by a third party (d) an assign-mentforthebenefitofcreditors,or(e)thedissolutionorliquidationoftheBuyer.18. Governing Law. This agreement and the sale and delivery of all Products here-under shall be deemed to have taken place in and shall be governed and construed in accordance with the laws of the State of Ohio, as applicable to contracts executed andwhollyperformedthereinandwithoutregardtoconflictsoflawsprinciples.Buyerirrevocably agrees and consents to the exclusive jurisdiction and venue of the courts of Cuyahoga County, Ohio with respect to any dispute, controversy or claim arising out of or relating to this agreement. Disputes between the parties shall not be settled by arbitration unless, after a dispute has arisen, both parties expressly agree in writing to arbitrate the dispute. 19. Indemnity for Infringement of Intellectual Property Rights. Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this Section. Seller will defend and indemnifyBuyeragainstallegationsofinfringementofU.S.patents,U.S.trademarks,copyrights, trade dress and trade secrets (“Intellectual Property Rights”). Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an actionbroughtagainstBuyerbasedonanallegationthataProductsoldpursuanttothisAgreement infringes the Intellectual Property Rights of a third party. Seller’s obligation todefendandindemnifyBuyeriscontingentonBuyernotifyingSellerwithinten(10)daysafterBuyerbecomesawareofsuchallegationsofinfringement,andSellerhavingsolecontrol over the defense of any allegations or actions including all negotiations for settle-ment or compromise. If a Product is subject to a claim that it infringes the Intellectual Property Rights of a third party, Seller may, at its sole expense and option, procure for BuyertherighttocontinueusingtheProduct,replaceormodifytheProductsoastomake it noninfringing, or offer to accept return of the Product and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information provided by Buyer,ordirectedtoProductsdeliveredhereunderforwhichthedesignsarespecifiedinwholeorpartbyBuyer,orinfringementsresultingfromthemodification,combinationoruse in a system of any Product sold hereunder. The foregoing provisions of this Section shallconstituteSeller’ssoleandexclusiveliabilityandBuyer’ssoleandexclusiveremedy for infringement of Intellectual Property Rights.20. Taxes. Unless otherwise indicated, all prices and charges are exclusive of excise, sales, use, property, occupational or like taxes which may be imposed by any taxing authority upon the manufacture, sale or delivery of Products.21. Equal Opportunity Clause. For the performance of government contracts andwhere dollar value of the Products exceed $10,000, the equal employment opportunity clausesinExecutiveOrder11246,VEVRAA,and41C.F.R.§§60-1.4(a),60-741.5(a),and60-250.4,areherebyincorporated.

Offer of Sale

AEROSPACEKey Markets• Aircraft engines• Business & general aviation• Commercial transports• Land-based weapons systems• Military aircraft• Missiles & launch vehicles• Regional transports• Unmanned aerial vehicles

Key Products• Flight control systems & components• Fluid conveyance systems• Fluid metering delivery & atomization devices• Fuel systems & components• Hydraulic systems & components• Inert nitrogen generating systems• Pneumatic systems & components• Wheels & brakes

CLIMATE CONTROLKey Markets• Agriculture• Air conditioning• Food, beverage & dairy• Life sciences & medical• Precision cooling• Processing• Transportation

Key Products• CO2 controls• Electronic controllers• Filter driers• Hand shut-off valves• Hose & fittings• Pressure regulating valves• Refrigerant distributors• Safety relief valves• Solenoid valves• Thermostatic expansion valves

FILTRATIONKey Markets• Food & beverage• Industrial machinery• Life sciences• Marine• Mobile equipment• Oil & gas• Power generation• Process• Transportation

Key Products• Analytical gas generators• Compressed air & gas filters• Condition monitoring• Engine air, fuel & oil filtration & systems• Hydraulic, lubrication & coolant filters• Process, chemical, water & microfiltration filters• Nitrogen, hydrogen & zero air generators

ELECTROMECHANICALKey Markets• Aerospace• Factory automation• Food & beverage• Life science & medical• Machine tools• Packaging machinery• Paper machinery• Plastics machinery & converting• Primary metals• Semiconductor & electronics• Textile• Wire & cable

Key Products• AC/DC drives & systems• Electric actuators• Controllers• Gantry robots• Gearheads• Human machine interfaces• Industrial PCs• Inverters• Linear motors, slides and stages• Precision stages• Stepper motors• Servo motors, drives & controls• Structural extrusions

PNEUMATICSKey Markets• Aerospace• Conveyor & material handling• Factory automation• Food & beverage• Life science & medical• Machine tools• Packaging machinery• Transportation & automotive

Key Products• Air preparation• Compact cylinders• Field bus valve systems• Grippers• Guided cylinders• Manifolds• Miniature fluidics• Pneumatic accessories• Pneumatic actuators & grippers • Pneumatic valves and controls• Rodless cylinders• Rotary actuators• Tie rod cylinders• Vacuum generators, cups & sensors

FLUID & GAS HANDLINGKey Markets• Aerospace• Agriculture• Bulk chemical handling• Construction machinery• Food & beverage• Fuel & gas delivery• Industrial machinery• Mobile• Oil & gas• Transportation• Welding

Key Products• Brass fittings & valves• Diagnostic equipment • Fluid conveyance systems• Industrial hose• PTFE & PFA hose, tubing & plastic fittings• Rubber & thermoplastic hose & couplings• Tube fittings & adapters• Quick disconnects

HYDRAULICSKey Markets• Aerospace• Aerial lift• Agriculture• Construction machinery• Forestry• Industrial machinery• Mining• Oil & gas• Power generation & energy• Truck hydraulics

Key Products• Diagnostic equipment• Hydraulic cylinders & accumulators• Hydraulic motors & pumps• Hydraulic systems• Hydraulic valves & controls• Power take-offs • Rubber & thermoplastic hose & couplings• Tube fittings & adapters• Quick disconnects

PROCESS CONTROLKey Markets• Chemical & refining• Food, beverage & dairy• Medical & dental• Microelectronics• Oil & gas• Power generation

Key Products• Analytical sample conditioning products & systems• Fluoropolymer chemical delivery fittings, valves & pumps• High purity gas delivery fittings, valves & regulators• Instrumentation fittings, valves & regulators• Medium pressure fittings & valves• Process control manifolds

SEALING & SHIELDINGKey Markets• Aerospace• Chemical processing• Consumer• Energy, oil & gas• Fluid power• General industrial• Information technology• Life sciences• Military• Semiconductor• Telecommunications• Transportation

Key Products• Dynamic seals• Elastomeric o-rings • EMI shielding• Extruded & precision-cut, fabricated elastomeric seals• Homogeneous & inserted elastomeric shapes • High temperature metal seals• Metal & plastic retained composite seals• Thermal management

Parker’s Motion & Control TechnologiesAt Parker, we’re guided by

a relentless drive to help

our customers become more

productive and achieve

higher levels of profitabil-

ity by engineering the best

systems for their require-

ments. It means looking at

customer applications from

many angles to find new

ways to create value. What-

ever the motion and control

technology need, Parker has

the experience, breadth of

product and global reach

to consistently deliver. No

company knows more about

motion and control technol-

ogy than Parker. For further

info call 1 800 C-Parker

(1 800 272 7537).

AEROSPACEKey Markets• Aircraft engines• Business & general aviation• Commercial transports• Land-based weapons systems• Military aircraft• Missiles & launch vehicles• Regional transports• Unmanned aerial vehicles

Key Products• Flight control systems & components• Fluid conveyance systems• Fluid metering delivery & atomization devices• Fuel systems & components• Hydraulic systems & components• Inert nitrogen generating systems• Pneumatic systems & components• Wheels & brakes

CLIMATE CONTROLKey Markets• Agriculture• Air conditioning• Food, beverage & dairy• Life sciences & medical• Precision cooling• Processing• Transportation

Key Products• CO2 controls• Electronic controllers• Filter driers• Hand shut-off valves• Hose & fittings• Pressure regulating valves• Refrigerant distributors• Safety relief valves• Solenoid valves• Thermostatic expansion valves

FILTRATIONKey Markets• Food & beverage• Industrial machinery• Life sciences• Marine• Mobile equipment• Oil & gas• Power generation• Process• Transportation

Key Products• Analytical gas generators• Compressed air & gas filters• Condition monitoring• Engine air, fuel & oil filtration & systems• Hydraulic, lubrication & coolant filters• Process, chemical, water & microfiltration filters• Nitrogen, hydrogen & zero air generators

ELECTROMECHANICALKey Markets• Aerospace• Factory automation• Food & beverage• Life science & medical• Machine tools• Packaging machinery• Paper machinery• Plastics machinery & converting• Primary metals• Semiconductor & electronics• Textile• Wire & cable

Key Products• AC/DC drives & systems• Electric actuators• Controllers• Gantry robots• Gearheads• Human machine interfaces• Industrial PCs• Inverters• Linear motors, slides and stages• Precision stages• Stepper motors• Servo motors, drives & controls• Structural extrusions

PNEUMATICSKey Markets• Aerospace• Conveyor & material handling• Factory automation• Food & beverage• Life science & medical• Machine tools• Packaging machinery• Transportation & automotive

Key Products• Air preparation• Compact cylinders• Field bus valve systems• Grippers• Guided cylinders• Manifolds• Miniature fluidics• Pneumatic accessories• Pneumatic actuators & grippers • Pneumatic valves and controls• Rodless cylinders• Rotary actuators• Tie rod cylinders• Vacuum generators, cups & sensors

FLUID & GAS HANDLINGKey Markets• Aerospace• Agriculture• Bulk chemical handling• Construction machinery• Food & beverage• Fuel & gas delivery• Industrial machinery• Mobile• Oil & gas• Transportation• Welding

Key Products• Brass fittings & valves• Diagnostic equipment • Fluid conveyance systems• Industrial hose• PTFE & PFA hose, tubing & plastic fittings• Rubber & thermoplastic hose & couplings• Tube fittings & adapters• Quick disconnects

HYDRAULICSKey Markets• Aerospace• Aerial lift• Agriculture• Construction machinery• Forestry• Industrial machinery• Mining• Oil & gas• Power generation & energy• Truck hydraulics

Key Products• Diagnostic equipment• Hydraulic cylinders & accumulators• Hydraulic motors & pumps• Hydraulic systems• Hydraulic valves & controls• Power take-offs • Rubber & thermoplastic hose & couplings• Tube fittings & adapters• Quick disconnects

PROCESS CONTROLKey Markets• Chemical & refining• Food, beverage & dairy• Medical & dental• Microelectronics• Oil & gas• Power generation

Key Products• Analytical sample conditioning products & systems• Fluoropolymer chemical delivery fittings, valves & pumps• High purity gas delivery fittings, valves & regulators• Instrumentation fittings, valves & regulators• Medium pressure fittings & valves• Process control manifolds

SEALING & SHIELDINGKey Markets• Aerospace• Chemical processing• Consumer• Energy, oil & gas• Fluid power• General industrial• Information technology• Life sciences• Military• Semiconductor• Telecommunications• Transportation

Key Products• Dynamic seals• Elastomeric o-rings • EMI shielding• Extruded & precision-cut, fabricated elastomeric seals• Homogeneous & inserted elastomeric shapes • High temperature metal seals• Metal & plastic retained composite seals• Thermal management

Parker’s Motion & Control TechnologiesAt Parker, we’re guided by

a relentless drive to help

our customers become more

productive and achieve

higher levels of profitabil-

ity by engineering the best

systems for their require-

ments. It means looking at

customer applications from

many angles to find new

ways to create value. What-

ever the motion and control

technology need, Parker has

the experience, breadth of

product and global reach

to consistently deliver. No

company knows more about

motion and control technol-

ogy than Parker. For further

info call 1 800 C-Parker

(1 800 272 7537).

Smart phone scan hereScanthisQRcodewithyoursmartphone to download the complete RDHcatalog.LookforQRcode readersatan"AppStore"foryourmobile device.

Parker Hannifin CorporationIndustrial Cylinder Division500SouthWolfRoadDesPlaines,IL60016USAphone(847)298-2400fax (800) 892-1008www.parker.com/cylinder

12/11 / Catalog HY08-1320-2/NA

Heavy Duty Hydraulic Roundline Cylinders - FPS Fluid … Cylinder RDH Heavy Duty... · fluid & gas...

Documents

Transcript of Heavy Duty Hydraulic Roundline Cylinders - FPS Fluid … Cylinder RDH Heavy Duty... · fluid & gas...