HEAT PUMP - Air Freeze Corp · HEAT PUMP Heat Pump 50 Hz DAIPL-12F The specifications, designs, and...

A system with the high capacity needed to suit large-sized buildings

HEAT PUMPHeat Pump50 Hz

DAIPL-12F

The specifications, designs, and information in this brochure are subject to change without notice.

Note Ask an authorised Daikin dealer to install Daikin products. Do not try to install the product yourself or get it installed by any unauthorised dealer. Improper installation can result in water or refrigerant leakage, electrical shock, fire or explosion. Warranty of the product shall be void if not installed by an authorised Daikin dealer.

Use only those parts and accessories supplied or specified by Daikin. Ask authorised Daikin dealer for any repairs or components. Warranty of the product / component shall be void if non specified spares are used or repaired by a non Daikin dealer.

Please ensure to install ELCB (Earth Leakage Circuit Breaker) for outdoor units to prevent ground fault effects. For details, please refer Note 7. Field wiring of page 10 in installation manual which comes along with the product.

For any inquiries, either call the numbers mentioned below or contact your nearer Daikin dealer.

Visit us at www.daikinindia.com

1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced.2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided. If you need to install the outdoor unit close to the sea shore, contact your local distributor.

Cautions on product corrosion

ISO 14001 is the standard defined by the International Organization for Standardization (ISO) relating to environmental management systems. Our group has been acknowledged by an internationally accredited compliance organisation as having an appropriate programme of environmental protection procedures and activities to meet the requirements of ISO 14001.

About ISO 14001ISO 9001 is a plant certification system defined by the International Organization for Standardization (ISO) relating to quality assurance. ISO 9001 certification covers quality assurance aspects related to the “design, development, manufacture, installation, and supplementary service” of products manufactured at the plant.

About ISO 9001

JMI-0107 JQA-1452

21

Latest individual air conditioning technology adds new real valueto today's buildings

Air conditioning systems that use new refrigerant and save energy are the norm. However, we at Daikin have gone much further by maximising our advanced technology developed over 25 years as the leading manufacturer of individual air conditioning systems. Not only top level air conditioning performance, we also offer minimal space utilisation, efficient building management and a multitude of other added value features.

Daikin’s VRV systems include indoor and outdoor units available in a wide range of models for various building sizes and installation conditions. Long refrigerant piping lengths and other features put few restrictions on design for great flexibility in meeting the needs of the building.

Daikin offers a compact design for VRVIII outdoor units by further optimising equipment functions, exceeding the norm for air conditioning systems. Compact units facilitate installation in limited areas, such as rooftops, and take up less effective space. Easier installation work realises fast completion with time to spare.

Benefits for INSTALLERS

With Daikin's proprietary inverter technology and cutting-edge control technology for refrigerant, the VRVIII air conditioning system operates with outstanding efficiency. This contributes to high energy savings, which greatly reduces your running costs and facilitates far better building management.

Benefits for

property OWNERS

To provide a comfortable air environment, Daikin offers air treatment systems beyond mere air conditioning. As well as bringing air to a comfortable temperature, the air quality can be treated with ventilation, humidification, and other processes. Ease of use is realised through advanced, centralised control systems.

Benefits for USERS

Benefits for CONSULTANTand DESIGN OFFICES

3

Developed to facilitate more flexible system design in large-sized buildings

Daikin proudly introduces the new VRVIII series, which is well-suited to large-sized buildings. This new air conditioning system provides outdoor units that extend air conditioning capacity up to 54 HP. It also incorporates numerous outstanding features, such as a wide range of outdoor and indoor units, longer actual and total piping length, and high external static pressure. The VRVIII series provides the power and versatility you need for flexible design and easy installation in large-sized buildings.

Outdoor units with large capacities................................................................page 7

Wide range and an increased number of connectable indoor units......page 9

High COPs/Energy savings

Compliant with the RoHS Directive

Extended level difference between outdoor units and indoor units.....page 10

Extended actual and total maximum piping length...................................page 10

High external static pressure..........................................................................page 11

Two types of outdoor unit combinations.....................................................page 11

Memory function for operational data

Automatic test operation

Less chances of refrigerant leakage

Easier installation and maintenance......................page12

A sense of responsibility..........................................page13

4

Outdoor units designed for quiet operation

Efficient compressor

Enhanced comfort....................................................page14

Nighttime quiet operation function

Contents

Technologies..................................page 5

Main Features................................page 7

Control Systems............................page 45Indoor Unit Lineup........................page 15

Outdoor Unit Lineup.....................page 29

Specifications................................page 31

Indoor units.....................................page 31Outdoor units..................................page 39

Option List.......................................page 41

Indoor units....................................page 41Outdoor units.................................page 44

Air Treatment Equipment Lineup...page 56

Outdoor-air processing unit............page 57HRV with DX-coil and humidifier.......page 61HRV.................................................page 65

Cutting-Edge Technologies

65

Daikin’s constant efforts have been devoted towards using the latest and most revolutionary technologies in the development of the VRVIII system for large-sized buildings. The system offers larger outdoor capacities, greater energy savings, easier installation, longer actual and total piping, and more.

VRVIII —Created to respond to the needs of large-sized buildings

The new heat exchanger contributes to a high COP because of an increase from 7% to 10% of the effective length as well as an optimised e-Pass heat exchanger.

3

7

1

26

5

3

4

7

2

1 Newly improved fans and grilles

Heat exchangerDC fan motor

4 Heat transfer circuit

By performing super cooling before the expansion process, the volume of refrigerant that needs to be circulated to the indoor units can be reduced without lowering the evaporation temperature. This permits the use of narrower piping.

5 Compact aero box

Realises a compact casing by stacking the Inverter and control PCBs plus optimising the internal design to suit airflow speed. This achieves lower noise and reduces the power required by the large-diameter fanned outdoor unit.

• Across entire range of models (from 6 to 54 HP).• Efficiency improvement by approximately 40% especially at

low speed.

6 Smooth sine wave DC Inverter

By adoption of the Sine Wave, which smoothes the rotation of the motor, operation efficiency is improved sharply.

DC fan motorstructure

Ferrite magnet

Secret to raising energy-efficiency! Powerful magnetsSecret to raising energy-efficiency! Powerful magnets

Neodymium magnets are much more powerful than the widely used ferrite magnets.

Neodymium magnet

ReluctanceDC motor

Improving the high efficiency compressor to achievea high COP and larger capacity

Reluctance DC scroll compressor

High torque and efficiency is attained with the adoption of neodymium magnets. Achieves 70% reduction in volume.

Daikin’s unique scroll compressor minimises heat loss, and is driven by a high efficiency motor to achieve significant energy savings.

By introducing high pressure oil, the reactive force from the fixed scroll is added to the internal force, thereby reducing thrust losses. This results in improved efficiency and suppressed sound levels.

High-performance, low-noise new scroll compressor operates at a faster rate. The speed increase has been achieved through advanced stress analysis for increased strength and utilisation of the advantages (oil film control) of the high thrust mechanism*.

*High thrust mechanism

200 300 400 500 600 700 800 900 1000

0

20

40

80

60

100

Eff

icie

ncy

(%

)

Motor speed (rpm)

AC motorAC motorAC motor

DC motor efficiency (comparison with a conventional AC motor)

Approx.

40%increase

Approx.

40%increase

DC motorDC motorDC motorDC motorDC motor

Note: Data are based on studies conducted under controlled conditions at a Daikin laboratory.

A higher external static pressure has been achieved–from 58. 8 Pa to 78.4 Pa–thanks to reduced internal pressure loss, use of the new fans and the new grilles.

The area of these new fan blades has been increased and optimised for each casing. This greatly reduces pressure loss, resulting in a higher external static pressure.

The three-bladed fan on the 10 HP unit, with a diameter of 700 mm, has been redesigned to include four blades and now has a diameter of 680 mm. Blade area has been increased by 25%.

New aero spiral fan and aero asymmetrical fan

Aero smooth grille

New aero asymmetrical fanIn the 14 and 16 HP unit, a single fan with a diameter of 700 mm has been split into two fans with diameters of 540 mm each. Blade area has been increased by 20% to increase airflow.

New aero spiral fan (Powerful Dual DC fan)

VRVII

The three-dimensional, integrated, soft woven steel grilles are covered with a plastic coating that protects them from rotating elements and the possibility of fire damage.

Blade area increased by

25%!

VRVIIBlade area increased by

20%!

Diameter of 700 mm Diameter of 540 mm x 2

Perspective view

Large capacities for large-sized buildings Large capacities for large-sized buildings

Main Features

87

The previous outdoor unit had a maximum output of 48 HP. The new units have a top output of 54 HP! Three more—a 50 HP model, a 52 HP model, and a 54 HP model, have been introduced, as well as a single 18 HP model that may serve as the main unit in combination solutions. With the introduction of these new models, outdoor unit combinations can be made more compact and flexible to suit large-sized buildings.

By providing a range of horse power levels in 2 HP increments*, Daikin responds flexibly to customer needs.

* Refer to page 30 for combination details.

Outdoor units

48 HP 54 HP

2 HP increments

Offering a higher capacity of up to 54 HP,responding to the needs of large-sized buildings

30, 32, 34, 36 HP

38, 40, 42, 44, 46 HP 48, 50, 52, 54 HP

6, 8, 10 HP 12, 14, 16, 18 HP

20, 22, 24, 26, 28 HP

VRVIIMA series

The latest technology is implemented in the VRVIII system. Surpassing even the VRVII, the new VRVIII responds to more of the needs of our customers that require air-conditioning solutions for large-sized buildings.

Major advances of the VRVIII over the VRVII for large-sized buildings

Indoor units

Ceiling Suspended FXHQ-MAVE

Ceiling MountedCassette Corner FXKQ-MAVE

Ceiling Mounted Cassette(Double Flow)

FXCQ-MVE

Daikin’s indoor unit system offers a large number of connectable indoor units—64! Furthermore, our wide range of indoor units to meet the needs of customers.

• R-410A VRV system indoor units are not compatible with the R-22 VRV system.Note:

• BEV units are necessary for Connection unit series indoor units. Note:

Connection unit series indoor units (50 Hz only)

Ceiling Suspended Cassette

Type Model Name—

1.6 HP0.8 HP 1.25 HP1 HP

FXUQ-MAV1

20 4031.2525BEVQ125MAVE

5 HP

BEVQ100MAVEBEVQ71MAVE

2 HP 4 HP3 HP50 12510071

Capacity Range

Connection UnitCapacity Index

Type Model NameCapacity Range

Capacity Index 20 40 62.5 80 100 1255031.2525

0.8 HP 1.6 HP 2.5 HP 3.2 HP 4 HP 5 HP

140

6 HP 8 HP2 HP1.25 HP1 HP

Floor Standing

ConcealedFloor Standing

FXLQ-MAVE

FXNQ-MAVE

Ceiling MountedCassette (Round Flow)

FXFQ-PVE

10 HP

250

16 HP

400

20 HP

500200Ceiling MountedCassette (Compact Multi Flow)

FXZQ-MVE

Floor StandingDuct FVYCP

FXDQ-PBVE/PBVE6

FXDQ-NBVE/NBVE6

FXMQ-MAVE/MVE6

FXMQ-PVE/PVE6

FXAQ-PVENew New New New New New NewWall Mounted

New 6 HP models are added to the lineup of VRVIII outdoor units.

New 6 HP modelsNew

Main Features

Large capacities for large-sized buildings Large capacities for large-sized buildings

Conditions of indoor unit connection capacity

109

The number of connectable indoor units has been drastically increased from 40 to 64!

An increased number of connectable indoor units

Connection capacity at maximum is 200%.

Combination ratio

40 64

Increased indoor unit connections

indoorunits

VRVIIMA series

indoorunits

Refer to page 30 for the maximum number of connectable indoor units.

Maximum number of connectable indoor units

Up toUp to

Note:* For the FXFQ25 models, maximum connection ratio is 130% for the entire range of outdoor units.

• If the operational capacity of indoor units is more than 130%, low airflow operation is enforced in all the indoor units.

50%–200%Connection capacity

Single outdoor units

Double outdoor units

Triple outdoor units

FXDQ, FXMQ-P, FXAQ models

Applicable indoor unitsOther indoorunit models*

200%200%

160%

130%

Piping length is drastically extended! The long piping length provides more design flexibility, which can match even large-sized buildings.

Extended long piping length

VRVII MA series

150 m 165 m

175 m 190 m

510 m 1000 m

Max. equivalent piping length

Max. actual piping length

50 m

40 m

VRVII MA series

VRVII MA series

VRVII MA series

p

q

k

First outdoor branch

fa

b

Firstindoor branch

Multiple use

*The rest of indoor units are the same as for single use.

a

i

s

r

hgf

edcbFirst indoor branch

Single use

Colours in the diagram above are merely for identifying pipes referenced with symbols such as a .

Max. total piping length

Max. level differencebetween the outdoor unitsand the indoor units

Outdoor unitabove indoor unit:

Outdoor unit above indoor unit:

2. Level differences above 50 m are available on request.

Outdoor unit below indoor unit:

Outdoor unit above indoor unit:

Outdoor unit below indoor unit:

Outdoor unitbelow indoor unit:

1. No special requirements up to 40 m. The maximum actual piping length can be 90 m, or less depending on conditions. Various conditions and requirements have to be met to allow utilisation of 90 m piping length.

2. Level differences above 50 m are not supported by default but are available on request for RXYQ8P-54P. (If the outdoor unit is above the indoor unit.).

Maximumallowablelevel difference

Maximumallowablepiping length

Between the outdoor unitsand the indoor units

Between the indoor units

Between the outdoor units (Multiple use)

Between the first indoor branch and the farthest indoor unit

Between the outdoor branch and the last outdoor unit

Total extension length

Refrigerant piping length

15 m or less

90 m or less

5 m or less

90 m or less

—

—

q

s

r

r

a+b+c+d+e+f+g+h+i

a+f+g+h+i

f+g+h+i

k+p

165 m or less 190 m or less

1000 m or less

90 m or less**1

10 m or less 13 m or less

Actualpiping length

Equivalentpiping length Example

Level Difference Example

RXYQ8P-54P

—

50 m or less rRXYQ6P

RXYQ8P-54P

Outdoor Units

2 Available on requestIf the outdoor unit is above.

If the outdoor unit is below.

If the outdoor unit is above.

If the outdoor unit is below. 40 m or less r

90 m 2

RXYQ8P-54P

90 m

40 m

50 m

RXYQ6P

Large capacities for large-sized buildings

Main Features

Easier installation and maintenance

High external static pressure 78.4 Pa (8 mm H2O)

58.8 Pa 78.4 Pa

Approx.

33.3%increase!

Selectable from two types of combinations

Automatic test operation

Memory function for operational data

Normal type (Space saving type)

* Refer to page 30 for outdoor combination details.

8

10

12

14

16

18

8

1

6

6

1

22

2

24

2

26

2

10

1

28

2

12

1

34

2

16

1

30

2

14

1

20

2

32

2

36

2

18

1Total number of connected outdoor units

HPSingle unit

8

10

12

14

16

18

6

40

3

38

3

42

3

46

3

48

3

44

3

50

3

52

3

54

3Total number of connected outdoor units

HPSingle unit

Higher external static pressure has been achieved thanks to the fan grilles and the dual DC fans that reduce internal pressure loss. Exceeding the previous 58.8 Pa (6 mm H2O) level, Daikin now offers 78.4 Pa (8 mm H2O) external static pressure by field setting to meet the requirements for installation on each floor, often requested for large-sized buildings.

VRVIIMA series

1211

Single outdoor units Double outdoor units

Triple outdoor units

Simply press the test operation button and the unit performs an automatic system check, including wiring, shutoff valves, and sensors. The results are returned automatically after the check finishes.

Operating data for the preceding 3 minutes is automatically stored in memory. Should a malfunction occur, this speeds up the process of identifying and fixing the cause of the problem. It also helps in developing measures to eliminate malfunctions.

78.4 Pa

Large capacities for large-sized buildings

Main Features

13

A sense of responsibility

High COPs

It has become essential for air conditioning manufacturers to develop systems that provide high energy savings. We at Daikin have made great efforts in this field, and the newly-developed VRVIII delivers highly efficient performance, contributing to high energy savings.

Compliant with the RoHS Directive*

We have been making efforts to facilitate the transition to using RoHS Directive*-compliant materials for system parts.

Less chances of refrigerant leakage

Conventionally, shutoff valve connections are flanged or flared. In the VRVIII system, the connections for all outdoor units are brazed, meaning less chance of refrigerant leakage.

* RoHS DirectiveThe RoHS (Restriction of Hazardous Substances (in electrical and electronic equipment)) Directive is an environmental directive enacted to regulate the use of designated chemical substances (lead, cadmium, hexavalent chromium, mercury, polybrominated biphenyls and polybrominated diphenylether) in electrical equipment.

Enhanced comfort

14

Outdoor units designed for low-sound operation

Outdoor units created with cutting-edge technologies provide quiet operation to increase users’ comfort.

Efficient compressor

New high-performance, low-sound scroll compressor operates at a faster rate, reducing start-up time. This helps the unit to bring the room temperature up to the set level quickly.

Nighttime quiet operation function

Set on the outdoor PCB. Time of maximum temperature is memorised. The low operating mode will initiate 8 hours*1 after the peak temperature in the daytime, and normal operation will resume 10 hours*2 after that. The operation sound level for the night mode can be selected from 55 dB(A) (Step 1),50 dB(A) (Step 2) and 45 dB(A) (Step 3).(For a single outdoor unit.)

Automatic mode

Operation sound level selectable from 3 steps for the night mode

Mode 1.

Automatic modeMode 1.

Starting time and ending time can be input. (An external control adaptor for outdoor unit, DTA104A53/61/62 or DTA114A61, and a subsequently obtained timer are necessary.)

Manual modeMode 2.

Combinations of modes 1 and 2 can be used depending on your needs.

Combined modeMode 3.

*1. Initial setting. Can be selected from 6, 8 and 10 hours.*2. Initial setting. Can be selected from 8, 9 and 10 hours.

• This function is available in setting at site.

• The relationship of outdoor temperature (load) and time shown in the graph is just an example.

The capacity reduction rate differs depending on the operation sound level step selected.

Notes:

Peak in outdoor temperature (For 10 HP outdoor unit)

Cap

acity

%

8 hrs 10 hrs

Ope

ratio

n so

und

dB(A

)

50

8:00 12:00 16:00 20:00 0:00 4:00 8:00

50

100

5855

0

Load

%

Night mode endsNight mode starts Night mode endsNight mode starts

Night Mode

45

(Initial setting)(Initial setting)

Step 2 max. - 8dB(A)



Step 2: 50 dB(A)

Step 1: 55 dB(A)

Step 3: 45 dB(A)

15

Type Model NameCapacity Range

Capacity Index 20 40 62.5 80 100 1255031.2525

0.8 HP 1.6 HP 2.5 HP 3.2 HP 4 HP 5 HP

140

6 HP 8 HP2 HP1.25 HP1 HP 10 HP

250

16 HP

400

20 HP

500200

Ceiling Suspended FXHQ-MAVE

ConcealedFloor Standing FXNQ-MAVE

Wall Mounted

Ceiling MountedCassette Corner FXKQ-MAVE

Ceiling Mounted Cassette(Double Flow)

FXCQ-MVE

• R-410A VRV system indoor units are not compatible with the R-22 VRV system.Note:

• BEV units are necessary for Connection unit series indoor units. Note:


Ceiling Suspended Cassette

Type Model Name—

1.6 HP0.8 HP 1.25 HP1 HP

FXUQ-MAV1

20 4031.2525BEVQ125MAVE

5 HP

BEVQ100MAVEBEVQ71MAVE

2 HP 4 HP3 HP50 12510071

Capacity Range

Connection UnitCapacity Index

Floor Standing FXLQ-MAVE

Ceiling MountedCassette (Round Flow)

FXFQ-PVE

Ceiling MountedCassette (Compact Multi Flow)

FXZQ-MVE

Floor StandingDuct FVYCP

FXMQ-MAVE/MVE6

FXMQ-PVE/PVE6

FXDQ-PBVE/PBVE6

FXDQ-NBVE/NBVE6

FXAQ-PVENew New New New New New New

Quiet, compact, and designed for user comfort

Dimensions correspond with 600 mm X 600 mm architectural module ceiling design specifications.

Wide discharge angle: 0° to 60°

2-, 3-, and 4-way airflow patterns are available, enabling installation in the corner of a room.

Comfortable airflow

Low operation sound level(240 V) (dB(A))

0°

60°

0°

60°

Auto swing Fixed angles: 5 levels

Angles can be also set on site to prevent drafts (0°-35°) or soiling of the ceiling (25°-60°), other than standard setting (0°-60°).

For 3-way or 2-way flow installation, the sealing member for air dischargeoutlet (option) must be used to close each unused outlet.

32/26Sound level

(H/L)

20/25 32 40 50

34/28 37/29 42/35

FXZQ-M

750 mm

Drain pump is equipped as standard accessory with 750 mm lift.

4-way flow 3-way flowL-shaped

2-way flow

1

2

0° 0°

60° 60°

FXZQ20MVE/FXZQ25MVE

FXZQ32MVE/FXZQ40MVE

FXZQ50MVE

Ceiling Mounted Cassette (Compact Multi Flow) Type

16

Indoor Unit Lineup

17

Ceiling Mounted Cassette (Round Flow) Type

360° airflow improves temperature distributionand offers a comfortable living environment.

FXFQ25P/FXFQ32P/FXFQ40P

FXFQ50P/FXFQ63P/FXFQ80P

FXFQ100P/FXFQ125P

Note: Whatever the discharge direction, the same type of panel is used. If installing for other than all-round flow, an air discharge outlet sealing member (option) must be used to close each unused outlet.

3-way flow L-shaped 2-way flowAll-round flow 4-way flow

GOOD DESIGNAWARD

IN JAPAN

850 mm

The industry’s first* Round Flow Ceiling Mounted Cassette type offers 360° airflow with improved temperature distribution.

All models are lighter than the conventional ones.Ex: Models FXFQ25P-50P are 4.5 kg lighter (reduced from 24 kg to 19.5 kg).

A new antibacterial treatment that uses silver ions has been applied to the drain pan, preventing the growth of slime, mould and bacteria that cause blockages and odours.

The horizontal louvres prevent dew condensation. Their non-flocking surfaces, which repel dirt, are easy to clean.

The air filter has an anti-mould and antibacterial treatment that prevents the growth of mould generated from dust or moisture that may adhere to the filter.

Example of airflow patterns:360° airflow is available, as well as 2- to 4-way flows, so you can choose the most suitable airflow pattern depending on location or room layout.

Drain pump is equipped as standard accessory, and the lift height has been improved from 750 mm to 850 mm.

Control of the airflow rate has been improved from 2-step to 3-step control.

(dB(A))

44/39/34

125

43/37.5/32

100

36/33.5/31

80

34/31/28

63

32/29.5/27

50

31/29/27

4032

30/28.5/27

25

Soundlevel

(HH/H/L)

FXFQ-P

Low operation sound level

4-way flow Round Flow

There are areas of uneven temperature.

There are much fewerareas of uneven temperature.

2019

Indoor Unit Lineup

Slim ceiling mounted duct type

Slim design, quietness and static pressure switching

FXDQ20PB/FXDQ25PB/FXDQ32PB

External static pressure selectable by remote controller switching make this indoor unit a very comfortable and flexible model.10 Pa-30 Pa/factory set: 10 Pa for FXDQ-PB models.15 Pa-44 Pa/factory set: 15 Pa for FXDQ-NB models.

Only 200 mm in height, this model can be installed in rooms with as little as 240 mm depth between the drop-ceiling and ceiling slab.

Only 700 mm in width and 23 kg in weight, this model is suitable to install in limited spaces like drop-ceilings in hotels.

1,100 mm in width for the FXDQ63NB model.

200mm900 mm

Suction grille*AIR

AIR

Discharge grille*

Air filterSuspension bolt*

240 mm

*: To be obtained locally

FXDQ-PB and FXDQ-NB models are available in two types to suit different installation conditions

Only 700 mm

200 mm

Great for hotel use!

Suited to use in drop-ceilings!

750 mm

Ceiling


36/34/32

63

35/33/31

50

34/32/30

40

33/31/29

32

33/31/29

25

33/31/29

20

Soundlevel (HH/H/L)

FXDQ-PB/NB

(dB(A))

The values of operation sound level represent those for rear-suction operation.Sound level values for bottom-suction operation can be obtained by adding 5 dB(A). Values are based on the following conditions:FXDQ-PB: external static pressure of 10 Pa; FXDQ-NB: external static pressure of 15 Pa.


FXDQ40NB/FXDQ50NB/FXDQ63NB

Wall Mounted Type

Stylish flat panel design harmonised with your interior décor

Drain pan and air filter can be kept clean by mould-proof polystyrene.

Drain pump kit is available as optional accessory, which lifts the drain 1,000 mm from the bottom of the unit.

Vertical auto-swing realises efficiency of air distribution. The louvre closes automatically when the unit stops.

5 steps of discharge angle can be set by remote controller.

Discharge angle is automatically set at the same angle as the previous operation when restarting. (Initial setting: 10˚ for cooling and 70˚ for heating)

Flexible installationDrain pipe can be fitted to from either left or right sides.

FXAQ20P/FXAQ25P

FXAQ32P/FXAQ40P

FXAQ50P/FXAQ63P

Drain pump kit

1,000 mm

Height of drain-up

Indoor unit

Stylish flat panel design creates a graceful harmony that enhances any interior space.

Flat panel can be cleaned with only the single pass of a cloth across their smooth surface.Flat panel can also be easily removed and washed for more thorough cleaning.


47/41

63

42/37

50

39/34

40

38/31

32

36/31

25

35/31

20

Sound level(H/L)

FXAQ-P

(dB(A))

New

Ceiling Mounted Duct Type

Indoor Unit Lineup

21

Middle and high static pressureallows for flexible duct design

FXMQ20P/FXMQ25P/FXMQ32PFXMQ40P/FXMQ50P/FXMQ63PFXMQ80P/FXMQ100P/FXMQ125P

Built-in Drain Pump (Option)Housing the drain pump inside the unit reduces the space required for installation.

All models are only 300 mm in height, an improvement over the 390 mm height of conventional models. The weight of the FXMQ40P has been reduced from 44 kg to 28 kg.

A DC fan motor increases the external static pressure capacity range to include middle to high static pressures, increasing design flexibility.

Indoor unit

470 mm

Indoor unit

470 mm

0–250mm

222 mm

Without drain pump With drain pump

Simplified Static Pressure ControlExternal static pressure can be easily adjusted using a change-over switch inside the electrical box to meet the resistance in the duct system.

FXMQ200MA/FXMQ250MA



(dB(A))

44/42/40

125

42/40/38

63

43/41/39

80/100

41/39/37

50

39/37/35

40

34/32/30

32

33/31/29

20/25

Soundlevel

(HH/H/L)

FXMQ-P

700 mm

Ceiling

30 Pa–100 Pa for FXMQ20P-32P30 Pa–160 Pa for FXMQ40P50 Pa–200 Pa for FXMQ50P-125P


Improved ease of installation

Improved ease of maintenance

Airflow can be controlled using a remote controller. With the conventional model, the airflow rate was controlled from the PC board. It is automatically adjusted to the range between approximately ±10% of the rated HH tap airflow.

The drain pan can be detached for easy cleaning. A new antibacterial treatment that uses silver ions has been applied to the drain pan, preventing the growth of slime, mould and bacteria that cause blockages and odours.

Energy-efficientThe adopted DC fan motor is much more efficient than the conventional AC motor, yielding an approximate 20% decrease in energy consumption. (FXMQ125P)

25 mm

Indoor Unit Lineup

Expanded Ceiling Mounted Duct Type Lineup(middle and high static pressure)

Easy maintenance

The drain pan can be detached for easy cleaning. An antibacterial treatment that uses Ag+ ions has been applied to the drain pan, preventing the growth of slime, mould and bacteria that cause blockages and odours.

Airflow can be adjusted in 10 steps using a remote controller during test operation.

The new 6 HP FXMQ140PVE has been added to the conventional lineup, expanding the FXMQ20-140PVE lineup to total of 10 models.


46/45/43Sound level(dB(A))

FXMQ140PVE

700 mm

Ceiling


31.252520 6350 10080 12540

3-step control airflow rate

3-step airflow rate control for better comfort.

140

1.25 HP1 HP0.8 HP

Capacity Index

FXMQ-PVE

Capacity Range 2.5 HP2 HP 4 HP3.2 HP 5 HP1.6 HP 6 HP

New

Middle and high static pressureallows for flexible duct design

A DC fan motor provides a wide external static pressure capacity range, increasing design flexibility.

Energy-efficient

The adopted DC fan motor is much more efficient than an AC motor, yielding an approximate 20% decrease in energy consumption.

Wide external static pressure capacity rangeEasy installation

Slim and lightweight design

Airflow adjustment function

Drain pump as a standard accessory

(HH/H/L)

300 mmHeightFXMQ140PVE

47 kgWeight

FXMQ140PVE: 50 Pa–140 Pa


6 HP FXMQ140PVE

22

FVYCP280MR

FVYCP450MR

FVYCP560MR

Easy maintenanceMost maintenance can be done from the front of the main unit.Maintenance can be completed in the mechanical room and does not interfere with office work.

Airflow rate

170

560

130

450

85

280

6,0004,5003,000

FVYCP-MR

m3/min

cfm

Long-life filter is included as standard equipment.

Belt driven, high static pressure type. Long duct length makes this unit versatile and useful.

Floor Standing Duct Type

23 24

Ceiling Mounted Cassette (Double Flow) Type

Thin, lightweight, and easy to install in narrow ceiling spaces

FXCQ20M/FXCQ25M/FXCQ32M

FXCQ40M/FXCQ50M/FXCQ63M

FXCQ80M/FXCQ125M

FXCQ-M 20

32/27

25/32

34/28

63

37/32

40/50

34/29

80

39/34

125

44/38

34/29 36/30 39/3437/32 41/36 46/40

(dB(A))

350 mm

The thin unit (only 350 mm high) can be installed in a ceiling space as narrow as 355 mm. All models feature a compact design with a depth of only 600 mm.

(When a high-efficiency filter is attached, the unit's height is 400 mm.)


Designed with higher airflow suitable for high ceiling application up to 3 metres.

Providing 2 different settings of standard and ceiling soiling prevention, the auto swing mechanism realises even distribution of airflow and room temperature.

Two types of optional high-efficiency filter are available (65% and 95% NBS).

A long-life filter (maintenance free up to one year) is equipped as standard accessory.

Drain pump is equipped as standard accessory with 600 mm lift. Major maintenance work can be performed by

removing the panel. A flat-type suction grille and a detachable blade make cleaning easy.

220V

240V

Soundlevel (H/L)

600 mm600 mm

Indoor Unit Lineup

25 26

Ceiling Mounted Cassette Corner Type

Slim design for flexible installation

3

32˚C 30˚C28˚C 26˚C 24˚C

22˚C

20˚C

2

1

0 1 2 3 4 5 6 (m)

(m)

Panel spacer

20 mm

Min.195 mm

Main body

Air discharge grille (option)

Set for front discharge using a suspended ceiling.

Downward discharge is shut off and air is blown straight out (front discharge).

Single-flow type allows effective air discharge from corner or from drop-ceiling.

Front discharge is possible with a air discharge unit (option), which allows the installation in the drop-ceiling or sagging wall.

Slim body needs only 220 mm space above the ceiling. If you use a panel spacer (option), the unit can be installed in the minimum space of 195 mm.


Providing 3 different settings of standard, draft prevention and ceiling soiling prevention, the auto swing mechanism realises even distribution of airflow and room temperature.

Main body

Downward discharge

Air discharge grille (option)

FXKQ25MA/FXKQ32MA

FXKQ40MA/FXKQ63MA

500 mm


Indoor Unit Lineup

Ceiling Suspended Type

Slim body with quiet and wide airflow

Adoption of newly designed QUIET STREAM FAN

Drain pump kit (option) can be easily incorporated.

Easy-to-clean flat design

Maintenance is easier because everything can be performed from below the unit.

Non-dew Flap with no implanted bristles

FXHQ-MA

Sound level(H/L)

32

36/31

63

39/34

100

45/37

(dB(A))Low operation sound level

Uses the quiet stream fan and many more advanced technologies.

Sound absorptionmember

Turbulent flow is produced

Straightening vane

Quiet stream fan

Installation is easy

Maintenance is easyDrain pump kit(built inside main unit)

600 mm

Bristle-free Flap minimises contamination and makes cleaning simpler.

Non-dew Flap


FXHQ32MA/FXHQ63MA

FXHQ100MA

2827

Floor Standing Type

Suitable for perimeter zone air conditioning

Wall hanging Floor installation

Floor Standing types can be hung on the wall for easier cleaning. Running the piping from the back allows the unit to be hung on walls. Cleaning under the unit, where dust tends to accumulate, is considerably easier.


The adoption of a fibre-less discharge grille featuring an original design to prevent condensation also helps prevent staining and makes cleaning easier.

Concealed Floor Standing Type

Designed to be concealed in the perimeter skirting-wall

Connecting port

Refrigerant piping

Applies also to Floor Standing type (FXNQ-MA).

The unit is concealed in skirting-wall of perimeter, that enables to create high class interior design.

The connecting port faces downward, greatly facilitating on-site piping work.


FXNQ20MA/FXNQ25MA

FXNQ32MA/FXNQ40MA

FXNQ50MA/FXNQ63MA

FXLQ20MA/FXLQ25MA

FXLQ32MA/FXLQ40MA

FXLQ50MA/FXLQ63MA

Indoor Unit Lineup

Ceiling Suspended Cassette Type (50 Hz only)

FXUQ71MAV1/FXUQ100MAV1

FXUQ125MAV1

Indoor Unit Lineup (Connection unit series indoor units)

This thin indoor unit achievesoptimum air distribution, and can be installed

without the need for ceiling cavity.

Depending on installation site requirements or room conditions, 2-way, 3-way and 4-way discharge patterns are available.

4-way airflowfrom the centre of the store.

The 3-way airflow can distributecomfortable air throughout the room.

Only one unit is needed to distribute comfortable airthroughout an L-shaped store.

Connection unit

NEW

Connection unit is the device for connecting above indoor unit to VRV III.

BEVQ-MAVE

Connection unit for indoor unit

Indoor unitPiping length*1

Indoor unit

Remote controller

Super wiring (DIII-NET)

Single-phase 220-240 Vpower supply

Refrigerant piping layout External wiring layout

Notes:

Gas pipeLiquid pipe

*1

• When connecting centralised-control device, it is necessary to install an interface adaptor for an indoor unit (DTA102A52).

• Connection unit BEVQ-MA is necessary for each indoor unit.

• The refrigerant piping height difference between the indoor units and the BEV unit must be within 4 m.

• The BEV unit must be installed within a maximum height difference between indoor units of 15 m.

• Branching of the refrigerant piping is not possible downstream of the BEV unit.

VRV series outdoor unit

BEVQ71MAVE/BEVQ100MAVE/BEVQ125MAVE

3029

• Between 12 (6 HP) and up to 64 (54 HP) indoor units in a single refrigerant piping circuit can be individually controlled in minimum increments of 2.2 kW (0.8 HP). Facilities from small to large can be accommodated with the lineup of 6–54 HP models. The units are superbly compact, so less installation space is required.

• Outdoor units with anti-corrosion specifications (-E type on request) are designed specifically for use in areas which are subject to salt damage and atmospheric pollution.

Normal type (Space saving type)

Series6 HP

Capacity range

8 HP 10 HP 12 HP 14 HP 16 HP 18 HP 20 HP 22 HP 24 HP 26 HP 28 HP 30 HP 32 HP 34 HP 36 HP 38 HP 42 HP 44 HP 46 HP 48 HP40 HP

Series Lineup

50 HP 52 HP 54 HP

30, 32, 34, 36 HP 38, 40, 42, 44, 46 HP 48, 50, 52, 54 HP

20, 22, 24, 26, 28 HP

RXYQ20PRY6/PAY6RXYQ22PRY6/PAY6RXYQ24PRY6/PAY6RXYQ26PRY6/PAY6RXYQ28PRY6/PAY6

12, 14, 16, 18 HP

RXYQ12PRY6/PAY6RXYQ14PRY6/PAY6RXYQ16PRY6/PAY6RXYQ18PRY6/PAY6

6, 8, 10 HP

RXYQ6PAY16RXYQ8PRY6/PAY6

RXYQ10PRY6/PAY6




Heat pump

Maximum number ofconnectable indoor units*HP Model name

RXYQ6PAY16

RXYQ8PRY6/PAY6

RXYQ10PRY6/PAY6

RXYQ12PRY6/PAY6

RXYQ14PRY6/PAY6

RXYQ16PRY6/PAY6

RXYQ18PRY6/PAY6

RXYQ20PRY6/PAY6

RXYQ22PRY6/PAY6

RXYQ24PRY6/PAY6

RXYQ26PRY6/PAY6

RXYQ28PRY6/PAY6

RXYQ30PRY6/PAY6

RXYQ32PRY6/PAY6

RXYQ34PRY6/PAY6

RXYQ36PRY6/PAY6

RXYQ38PRY6/PAY6

RXYQ40PRY6/PAY6

RXYQ42PRY6/PAY6

RXYQ44PRY6/PAY6

RXYQ46PRY6/PAY6

RXYQ48PRY6/PAY6

6 HP

8 HP

10 HP

12 HP

14 HP

16 HP

18 HP

20 HP

22 HP

24 HP

26 HP

28 HP

30 HP

32 HP

34 HP

36 HP

38 HP

40 HP

42 HP

44 HP

46 HP

48 HP

10 (15)

13 (20)

16 (25)

19 (30)

23 (35)

26 (40)

29 (45)

32 (40)

35 (44)

39 (48)

42 (52)

45 (56)

48 (60)

52 (64)

55 (64)

58 (64)

61 (61)

64 (64)

Normal Type (Space Saving Type)Outdoor unit multi

connection piping kit

–

–

–

–

–

–

–

BHFP22P100

BHFP22P151

Combination

RXYQ6PAY16

RXYQ8PRY6/PAY6

RXYQ10PRY6/PAY6

RXYQ12PRY6/PAY6

RXYQ14PRY6/PAY6

RXYQ16PRY6/PAY6

RXYQ18PRY6/PAY6

RXYQ8PRY6/PAY6+RXYQ12PRY6/PAY6






RXYQ16PRY6/PAY6 x 2


RXYQ18PRY6/PAY6 x 2

RXYQ8PRY6/PAY6+RXYQ12PRY6/PAY6+RXYQ18PRY6/PAY6

RXYQ8PRY6/PAY6 +RXYQ16PRY6/PAY6 x 2

RXYQ8PRY6/PAY6+RXYQ16PRY6/PAY6 +RXYQ18PRY6/PAY6

RXYQ8PRY6/PAY6+RXYQ18PRY6/PAY6 x 2





RXYQ18PRY6/PAY6 x 3

Total capacity index of connectable indoor units*

105 to 195 (300)

100 to 260 (400)

125 to 325 (500)

150 to 390 (600)

175 to 455 (700)

200 to 520 (800)

225 to 585 (900)

250 to 650 (800)

275 to 715 (880)

300 to 780 (960)

325 to 845 (1,040)

350 to 910 (1,120)

375 to 975 (1,200)

400 to 1,040 (1,280)

425 to 1,105 (1,360)

450 to 1,170 (1,440)

475 to 1,235 (1,235)

500 to 1,300 (1,300)

525 to 1,365 (1,365)

550 to 1,430 (1,430)

575 to 1,495 (1,495)

600 to 1,560 (1,560)

625 to 1,625 (1,625)

650 to 1,690 (1,690)

675 to 1,755 (1,755)

RXYQ50PRY6/PAY6

RXYQ52PRY6/PAY6

RXYQ54PRY6/PAY6

50 HP

52 HP

54 HP

Note: •For multiple connection of 20 HP systems and above, the above Daikin optional kit (separately sold) is required.*Values inside brackets are based on connection of indoor units rated at maximum capacity, 200% for single outdoor units, 160% for double outdoor units, and 130% for triple outdoor units. Refer to page 9 for notes on connection capacity of indoor units.

Outdoor unit combinations

Indoor Unit Lineup

3231

INDOOR UNITS

Ceiling Mounted Cassette (Round Flow) Type

MODEL FXFQ25PVE

Cooling capacity

kW(*1)

(*2)

2.9

9,900

2,500

3.2

10,900

Galvanised steel plate

2,800

246X840X840

19.5

6.4

12.7

VP25 (External Dia, 32/Internal Dia, 25)

BYCP125K-W1

Fresh white

50X950X95050X950X95050X950X95050X950X95050X950X95050X950X95050X950X95050X950X950

5.55.55.55.55.55.55.55.5

246X840X840

19.5

6.4

12.7

FXFQ32PVE

3.7

12,600

3,200

4.0

13,600

3,400

15/13/1113/11.5/10 13/11.5/10

30/28.5/27 30/28.5/27

530/459/388

31/29/27

246X840X840

19.5

6.4

12.7

FXFQ40PVE

4.7

16,000

4,000

5.0

17,100

4,300

16/13.5/11

565/477/388459/406/353 459/406/353

32/29.5/27

246X840X840

19.5

6.4

12.7

FXFQ50PVE

5.8

19,800

5,000

6.3

21,500

5,400

19/16.5/13.5

671/583/477

34/31/28

246X840X840

22

9.5

15.9

FXFQ63PVE

7.3

24,900

6,300

8.0

27,300

6,900

21/18/15

742/636/530

36/33.5/31

246X840X840

22

9.5

15.9

FXFQ80PVE

9.3

2.8 3.6 4.5 5.6 7.1 9.0

31,700

8,000

10.0

34,100

8,600

FXFQ100PVE

11.6

39,600

10,000

12.5

42,700

10,800

FXFQ125PVE

14.5

11.2 14.0

49,500

12,500

16.0

54,600

13,800

32/26/20

1,130/918/706

43/37.5/32

288X840X840

25

9.5

15.9

33/28/22.5

1,165/989/794

44/39/34

288X840X840

25

9.5

15.9

Btu/h(*1)

kcal/h(*1)

Heating capacity

kW

Btu/h

kcal/h

Casing

1-phase, 220-240 V, 50 HzPower supply

Airflow rate(HH/H/L)

m3/min

cfm

Dimensions (HXWXD) mm

Machine weight kg

Piping connections

Drain piping

Panel (Option) Model

Colour

mmDimensions(HXWXD)

weight kg

dB(A)Sound level (HH/H/L)

Liquid (Flare)

Gas (Flare)

mm

mm

Note : Specifications are based on the following conditions;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB. (*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.•Equivalent piping length : 7.5 m•Level difference : 0 m•Capacity of indoor unit is only for reference. Actual capacity of indoor unit is based on the total capacity index. •Sound level : Anechoic chamber conversion value, measured at a point 1.5 m downward from the unit centre. During actual operation, these values are normally somewhat higher as a result of ambient conditions.

Ceiling Mounted Cassette (Compact Multi Flow) Type

1-phase, 220-240 V, 50 Hz

2.3

8,500

2,200

2.5

7,800

2,000

FXZQ20MVE

2.2

FXZQ25MVE

2.9

9,900

2,500

3.2

10,900

2,800

2.8

FXZQ32MVE

3.7

3.6

4.0

13,600

3,400

FXZQ40MVE

4.7

4.5

16,000

4,0003,200

12,600

5.0

17,100

4,300

FXZQ50MVE

5.8

5.6

19,800

5,000

6.3

21,500

5,400

MODEL

kW(*1)

Btu/h(*1)

kcal/h(*1)

Heating capacitykW

Btu/h

(*2)

kcal/h

Power supply

Cooling capacity

6.4

12.7

55X700X700

2.7

286X575X575

18


BYFQ60B8W1

White (6.5Y9.5/0.5)


493/353

14/10

41/33-42/35-41/34

318/247

6.4

12.7

55X700X700

2.7

9/7

30/25-32/26-32/29

318/247

6.4

12.7

55X700X700

2.7

9/7

30/25-32/26-32/29

335/265

6.4

12.7

55X700X700

2.7

9.5/7.5

32/26-34/28-33/29

388/282

6.4

12.7

55X700X700

2.7

11/8

36/28-37/29-36/30


Machine weight kg

Casing

Airflow rate (H/L)m3/min

cfm

Sound level (H/L) dB(A)230 V-240 V-220 V, 60 Hz

Pipingconnections

Drain

Panel(Option)

Model

Colour

mmDimensions (HXWXD)

Weight kg

Liquid (Flare)

Gas (Flare) mm

Specifications

INDOOR UNITSINDOOR UNITS

Slim Ceiling Mounted Duct Type (700 mm width type)

Cooling capacity

kW(*1)

7,800

2,000

9,900

2,500

12,600

3,200

(*2) 2.2

Btu/h(*1)

kcal/h(*1)

8,500

2,200

10,900

2,800

13,600

3,400

Btu/h

2.5 3.2 4.0kW

kcal/hHeating capacity


2.8 3.6

2.3 2.9 3.7

MODEL FXDQ20PBVE/PBVE6 FXDQ25PBVE/PBVE6 FXDQ32PBVE/PBVE6with drain pump


8.0/7.2/6.4

282/254/226

8.0/7.2/6.4

282/254/226

8.0/7.2/6.4

282/254/226

33/31/29 33/31/29 33/31/29

Airflow rate (HH/H/L)

m3/min

cfm

dB(A)

Casing

200X700X620

23.0

6.4

12.7

200X700X620

23.0

6.4

12.7

200X700X620

23.0

6.4

12.7

Dimensions (HXWXD)

Sound level (HH/H/L)

PaExternal static pressure

mm

Machine weight kg

Piping connections

Drain piping VP20 (External Dia, 26/Internal Dia, 20)

30-10 1

32

Liquid (Flare)

Gas (Flare)

mm

mm

Cooling capacity

kW(*1)

(*2)

Btu/h(*1)

kcal/h(*1)

Btu/h

kW

kcal/h

Slim Ceiling Mounted Duct Type (900/1,100 mm width type)

Heating capacity


with drain pumpMODEL

16,000

4,000

19,800

5,000

24,900

6,300

17,100

4,300

21,500

5,400

27,300

6,900

5.0 6.3 8.0

4.5 5.6 7.1

4.7 5.8 7.3

FXDQ40NBVE/NBVE6 FXDQ50NBVE/NBVE6 FXDQ63NBVE/NBVE6

Note : Specifications are based on the following conditions;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB. (*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.

1 : External static pressure is changeable to set by the remote controller. This pressure means "High static pressure - Standard". (Factory setting is 10 Pa. for PBVE & 15 Pa for NBVE)

2 : The values of operation sound level represent those for rear-suction operation. Sound level values for bottom-suction operation can be obtained by adding 5 dB(A). 3 : Values are based on the following conditions: external static pressure of 10 Pa for PBVE & 15 Pa for NBVE.•Equivalent piping length : 7.5 m •Level difference : 0 m•Capacity of indoor unit is only for reference. Actual capacity of indoor unit is based on the total capacity index. •Sound level (FXDQ-PB) Anechoic chamber conversion value, measured at a point 1.5 m downward from the unit centre. (FXDQ-N(B)) Anechoic chamber conversion value, measured at a point 1.5 m downward from the unit centre. During actual operation, these values are normally somewhat higher as a result of ambient conditions.


Airflow rate(HH/H/L)

m3/min

cfm

dB(A)

Casing

Dimensions (HXWXD)

PaExternal static pressure

mm

Machine weight kg

Piping connections

Drain piping VP20 (External Dia, 26/Internal Dia, 20)

44-15 1

10.5/9.5/8.5

371/335/300

12.5/11.0/10.0

441/388/353

16.5/14.5/13.0

583/512/459

34/32/30 35/33/31 36/34/32

200X900X620

27.0

6.4

12.7

200X900X620

28.0

6.4

12.7

200X1,100X620

31.0

9.5

15.9

Sound level (HH/H/L) 32

Liquid (Flare)

Gas (Flare)

mm

mm

3433

Specifications

INDOOR UNITS

Note : Specifications are based on the following conditions;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB. (*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.•Equivalent piping length : 7.5m •Level difference : 0m•Capacity of indoor unit is only for reference. Actual capacity of indoor unit is based on the total capacity index. •Sound level Anechoic chamber conversion value, measured at a point 1 m in front of the unit and 1 m downward.

During actual operation, these values are normally somewhat higher as a result of ambient conditions.

Wall Mounted Type

FXAQ25PVE

2.9

3.2

White (3.0Y8.5/0.5)

36/31

290X795X238

11

Casing

1-phase, 220-240 V/220 V, 50 Hz

38/31

290X795X238

11

FXAQ40PVE

4.7

5.0

39/34

290X1,050X238

14

9,900 16,000

2,500 4,000

10,900 17,100

2,800 4,300

282/177 300/194 424/318

m3/minAirflow rate (H/L)

cfm

8/5 8.5/5.5

13,600

3,400

FXAQ32PVE

3.7

12,600

3,200

4.0

2.8

FXAQ20PVE

2.3

2.5

35/31

290X795X238

11

7,800

2,000

8,500

2,200

265/159

7.5/4.5

2.2 4.53.6

12/9


6.4 6.4 6.4 6.4

12.7 12.7 12.7 12.7

42/37

290X1,050X238

14

FXAQ63PVE

7.3

24,900

6,300

27,300

6,900

15/12 19/14

530/424

8.0

47/41

290X1,050X238

14

671/494

21,500

5,400

6.3

5,000

FXAQ50PVE

5.8

19,800

7.15.6

6.4 9.5

12.7 15.9

Heating capacity

kW

Btu/h

kcal/h

MODELPower supply

Cooling capacity

kW(*1)

(*2)

Btu/h(*1)

kcal/h(*1)


Machine weight kg

dB(A)Sound level (H/L)

Pipingconnections

Drain

Liquid (Flare)

Gas (Flare) mm

INDOOR UNITS


FXMQ200MAVE/MVE6 FXMQ250MAVE/MVE6

23.0

78,500

19,800

28.8

22.4 28.0

98,300

24,800

1-phase, 220-240 V, 50 Hz

MODELPower supply

Cooling capacity

kW(*1)

(*2)

Btu/h(*1)

kcal/h(*1)

External static pressure Pa60 Hz

50 Hz


58/50

2,047/1,765

470X1,380X1,100

137.0

9.5

19.1

PS1B

72/62

2,542/2,189

470X1,380X1,100

137.0

9.5

22.2

132-221 191-270 2

132-270 147-270 2 2

2

48/45 48/45

49/46 49/46

Casing

m3/min

cfm


Machine weight kg

Airflow rate (H/L)

Sound level(H/L)

dB(A)220 V

240 V

Pipingconnections

Drain

Liquid (Flare)

Gas (Brazing) mm

Note : Specifications are based on the following conditions;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB.

(*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB. 1 : External static pressure can be modified using a remote controller that offers seven (FXMQ20-32P), thirteen (FXMQ40P) or fourteen (FXMQ50-125P),ten (FXMQ 140P) levels of control. These values indicate the lowest and highest possible static pressures. The standard static pressure is 50 Pa for FXMQ20-32P and 100 Pa for FXMQ40-140P. 2 : External static pressure is changeable to change over the connectors inside electrical box, this pressure means "Standard-High static pressure".•Equivalent piping length : 7.5 m•Level difference : 0 m•Capacity of indoor unit is only for reference. Actual capacity of indoor unit is based on the total capacity index. •Sound level : Anechoic chamber conversion value, measured at a point 1.5 m downward from the unit centre.



FXMQ40PVE/6 FXMQ50PVE/6 FXMQ63PVE/6 FXMQ80PVE/6 FXMQ100PVE/6 FXMQ125PVE/6

4.7

16,000

4,000

5.0

17,100


4,300

565/459/388

300X700X700

28.0

6.4

12.7


5.8

19,800

5,000

6.3

21,500

5,400

635/582/530

300X1,000X700

36.0

6.4

12.7

7.3

24,900

6,300

8.0

27,300

6,900

688/618/565

300X1,000X700

36.0

9.5

15.9

9.3

31,700

8,000

10.0

34,100

8,600

883/794/706

300X1,000X700

36.0

9.5

15.9

11.6

39,600

10,000

12.5

42,700

10,800

1,130/953/812

300X1,400X700

46.0

9.5

15.9

14.5

49,500

12,500

16.0

54,600

13,800

1,377/1,165/988

300X1,400X700

46.0

9.5

15.9

4.5 5.6 7.1 9.0 11.2 14.0

Heating capacity

kW

Btu/h

kcal/h

cfm

External static pressure

Casing

1-phase, 220-240 V/, 50 Hz

Airflow rate (HH/H/L)16/13/11 18/16.5/15 19.5/17.5/16 25/22.5/20 32/27/23 39/33/28m3/min

Pa 30-160 50-200 50-200 50-200 50-200 50-200 1 1 1 1 1 1

39/37/35

FXMQ20PVE

2.3

7,800

2,000

2.5

8,500

2,200

318/265/230

300X550X700

25.0

6.4

12.7

2.2

9/7.5/6.5

30-100

33/31/29

FXMQ25PVE

2.9

9,900

2,500

3.2

10,900

2,800

318/265/230

300X550X700

25.0

6.4

12.7

2.8

9/7.5/6.5

30-100

33/31/29

FXMQ32PVE

3.7

12,600

3,200

4.0

13,600

3,400

335/282/247

300X550X700

25.0

6.4

12.7

3.6

9.5/8/7

30-100

34/32/30 41/39/37 42/40/38 43/41/39 43/41/39 44/42/40Sound level (HH/H/L) dB(A)

(*1)

(*2)

MODELPower supply

Cooling capacity

kW

Btu/h(*1)

kcal/h(*1)

Drain


Machine weight kg

Pipingconnections

Liquid (Flare)

Gas (Flare) mm

1 1 1

FXMQ140PVE/6

16.7

57,000

14,300

18.0

61,400

15,500

1,624/1,377/1,130

300X1,400X700

47.0

9.5

15.9

16.0

46/39/32

50-140 1

46/45/43

35

Specifications

36

INDOOR UNITS

Ceiling Mounted Cassette Corner Type

FXKQ25MAVE

kW(*1) 2.9

9,900

2,500

3.2

10,900

2,800

Btu/h(*1)

kcal/h(*1)

Heating capacity

kW

Btu/h

FXKQ32MAVE

3.7

12,600

3,200

4.0

13,600

3,400

FXKQ40MAVE

4.7

16,000

4,000

5.0

17,100

4,300

FXKQ63MAVE

7.3

(*2) 2.8 3.6 4.5 7.1

24,900

6,300

8.0

27,300

6,900kcal/h

1 phase, 220-240V, 50 HzPower supply

Cooling capacity

MODEL

Galvanized steel plate

11/9 11/9 13/10 18/15

388/318 388/318 459/353 635/530

215X1,110X710

31.0

6.4

12.7


BYK45FJW1

White (10Y9/0.5)

70X1,240X800

8.5

215X1,110X710

31.0

6.4

12.7

70X1,240X800

8.5

215X1,110X710

31.0

6.4

12.7

70X1,240X800

8.5

215X1,310X710

34.0

9.5

15.9

BYK71FJW1

70X1,440X800

9.5


Machine weight kg

Piping connections Liquid(Flare)mm

Gas(Flare)mm

Drain piping


Colour

mm

weight kg

Dimensions(HXWXD)

38/33 38/33 40/34 42/37

40/35 40/35 42/36 44/39

Casing

Air flow rate (Hi/Lo) m3/min

cfm

50 Hz

50 Hz

Sound level (Hi/Lo) dB (A)

50 Hz/60 Hz 220V

50 Hz 240V

MODEL FXHQ32MAVE

Cooling capacity

kW(*1) 3.7

12,600

3,200

4.0

13,600

3,400

FXHQ63MAVE

7.3

24,900

6,300

8.0

27,300

6,900

FXHQ100MAVE

11.6

(*2) 3.6 7.1 11.2

39,600

10,000

12.5

42,700

10,800

Btu/h(*1)

kcal/h(*1)

Heating capacity

kW

Btu/h

kcal/h

Ceiling Suspended Type


White (10Y9/0.5)

cfm

12/10 17.5/14 25/19.5


Machine weight kg

Piping connections

Drain piping

36/31 39/34 45/37

195X960X680

24.0

6.4

12.7


195X1,160X680

28.0

9.5

15.9

195X1,400X680

33.0

9.5

15.9

Casing


424/353 883/688618/494

dB(A)Sound level (H/L)

Note : Specifications are based on the following conditions;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB.

(*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB. 1 : External static pressure can be modified using a remote controller that offers fourteen levels of control. These values indicate the lowest and highest possible static pressures. The standard static pressure is 100 Pa. 2 : External static pressure is changeable to change over the connectors inside electrical box, this pressure means "Standard-High static pressure".•Equivalent piping length : 7.5 m•Level difference : 0 m•Capacity of indoor unit is only for reference. Actual capacity of indoor unit is based on the total capacity index. •Sound level : (FXKQ-MA) Anechoic chamber conversion value, measured at a point 1 m in front of the unit and 1 m downward.

(FXHQ-M) Anechoic chamber conversion value, measured at a point 1 m in front of the unit and 1 m downward.During actual operation, these values are normally somewhat higher as a result of ambient conditions.

Liquid (Flare)

Gas (Flare)

mm

mm

Specifications are based on the following conditions;•Cooling : Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.

INDOOR UNITS

FVYCP280M9R

28.0

95,600

24,100

31.5

107,500

27,100

FVYCP450MR

45.0

153,600

38,700

50.0

170,600

43,000

250 400

3-phase, 380-415 V, 50 Hz

kW

Btu/h

kcal/h

Power supply

Capacity index

Cooling capacity

MODEL

Heating capacity

kW

Btu/h

kcal/h


85 130

3,000 4,500

1,670X1,170X510

145

9.5

22.2

Ps1 Internal Dia

1,870X1,170X720

210

12.7

28.6

Airflow rate (H)m3/min

cfm

Casing


270 400

FVYCP560MR

56.0

191,300

48,200

500

63.0

215,100

54,200

170

6,000

1,870X1,470X720

240

15.9

28.6

480External static pressure Pa

Machine weight kg

Pipingconnections

Drain

Liquid (Flare)

Gas (Flare) mm

FXCQ20MVE FXCQ25MVE FXCQ32MVE FXCQ40MVE FXCQ50MVE FXCQ63MVE FXCQ80MVE FXCQ125MVE

2.3

7,800

2,000

2.5

8,500

2,200

2.9

9,900

2,500

3.2

10,900

2,800

3.7

12,600

3,200

4.0

13,600

3,400

4.7

16,000

4,000

5.0

17,100

4,300

5.8

19,800

5,000

6.3

21,500

5,400

7.3

24,900

6,300

8.0

27,300

6,900

9.3

31,700

8,000

10.0

34,100

8,600

14.5

2.2 2.8 3.6 4.5 5.6 7.1 9.0 14.0

49,500

12,500

16.0

54,600

13,800


MODEL

Cooling capacity

kW(*1)

(*2)

Btu/h(*1)

kcal/h(*1)

Heating capacity

kW

Btu/h

kcal/h



7/5

247/177

32/27

305X775X600

26.0

6.4

12.7


BYBC32G-W1

White (10Y9/0.5)

53X1,030X680

8.0

9/6.5

318/230

34/28

305X775X600

26.0

6.4

12.7

53X1,030X680

8.0

9/6.5

318/230

34/28

305X775X600

26.0

6.4

12.7

53X1,030X680

8.0

12/9

424/318

34/29

305X990X600

31.0

6.4

12.7

BYBC50G-W1

53X1,245X680

8.5

12/9

424/318

34/29

305X990X600

32.0

6.4

12.7

53X1,245X680

8.5

16.5/13

582/459

37/32

305X1,175X600

35.0

9.5

15.9

BYBC63G-W1

53X1,430X680

9.5

26/21

918/741

39/34

305X1,665X600

47.0

9.5

15.9

BYBC125G-W1

53X1,920X680

12.0

33/25

1,165/883

44/38

34/29 36/30 36/30 37/32 37/32 39/34 41/36 46/40

305X1,665X600

48.0

9.5

15.9

53X1,920X680

12.0

Casing

Airflow rate (H/L) m3/min

cfm


Machine weight kg

Piping connections

Drain piping


Colour

mm

Sound level (H/L)

Dimensions(HXWXD)

weight kg

dB (A)

220V

240V

Liquid (Flare)

Gas (Flare)

mm

mm

Note : Specifications are based on the following conditions;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB. (*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.•Equivalent piping length : 7.5 m•Level difference : 0 m•Capacity of indoor unit is only for reference. Actual capacity of indoor unit is based on the total capacity index. •Sound level : Anechoic chamber conversion value, measured at a point 1.5 m downward from the unit centre. During actual operation, these values are normally somewhat higher as a result of ambient conditions.


3837

Specifications

INDOOR UNITS

Note : Specifications are based on the following conditions ;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB.

(*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.•Equivalent piping length : 7.5 m•Level difference : 0 m•Capacity of indoor unit is only for reference. Actual capacity of indoor unit is based on the total capacity index. •Sound level : (FXLQ-MA,FXNQ-MA) Anechoic chamber conversion value, measured at a point 1.5 m infront of the unit at a height of 1.5m. During actual operation, these values are normally somewhat higher as a result of ambient conditions.

Floor Standing Type/Concealed Floor Standing Type

MODELFXLQ20MAVE

Cooling capacity

2.3

7,800

2,000

8,500

2,200

Btu/h(*1)

kcal/h(*1)

Heating capacity

kW

Btu/h

kcal/h

Power supply

2.2

FXLQ25MAVE

2.9

9,900

2,500

10,900

2,800

2.8

FXLQ32MAVE

3.7

12,600

3,200

13,600

3,400

3.6

FXLQ40MAVE

4.7

16,000

4,000

17,100

4,300

4.5

FXLQ50MAVE

5.8

19,800

5,000

6.3

21,500

5,400

5.6

FXLQ63MAVE

FXNQ20MAVE FXNQ25MAVE FXNQ32MAVE FXNQ40MAVE FXNQ50MAVE FXNQ63MAVE

7.3

24,900

6,300

8.0

27,300

6,900

7.1kW

(*1)

(*2)

2.5 3.2 4.0 5.0

FXLQ

FXNQ

1-phase, 220-240 V, 50 Hz

FXLQ: Ivory white (5Y7.5/1) / FXNQ: Galvanised steel plateCasing

Airflow rate (H/L) m3/min

cfm

7/6

247/212

600X1,000X222

25.0

6.4

12.7

21O.D.

Dimensions (HXWXD)

Machine weight

Piping connections

Drain piping

7/6

247/212

600X1,000X222

25.0

6.4

12.7

282/212 388/300 494/388 565/424

8/6

600X1,140X222

30.0

6.4

12.7

11/8.5

600X1,140X222

30.0

6.4

12.7

14/11

600X1,420X222

36.0

6.4

12.7

16/12

600X1,420X222

610X930X220 610X930X220 610X1,070X220 610X1,070X220 610X1,350X220 610X1,350X220

36.0

19.0 19.0 23.0 23.0 27.0 27.0

9.5

15.9

mmFXLQ

FXNQ

kgFXLQ

FXNQ

35/32 35/32 35/32 38/33 39/34 40/35

37/34 37/34 37/34 40/35 41/36 42/37Sound level (H/L) dB

(A)

220V

240V

Liquid (Flare)

Gas (Flare)

mm

mm

INDOOR UNITS

Ceiling Suspended Cassette Type

kW(*1)

(*2)

Kcal/h(*1)

Power supply

8.3

7,1001-phase, 220-240 V, 50 Hz

Btu/h(*1) 28,300

kW

Kcal/hHeating capacity (Max.)

9.0

7,700Btu/h 30,700

11.6

10,00039,600

12.5

10,80042,700

14.58.0 11.2 14.0

12,50049,500

14.0

12,00047,800

Cooling capacity

ModelIndoor unit

Connection unit BEVQ71MAVEFXUQ71MAV1

BEVQ100MAVEFXUQ100MAV1

BEVQ125MAVEFXUQ125MAV1


* A type of BEV unit is necessary for each Connection unit series indoor unit. Refer to the Engineering Data for details.* If indoor units from the Connection unit series are connected within a single refrigerant system to indoor units from any other

series, cooling/heating switchover will not be possible using the remote controller of the Connection unit series indoor units. However, if the remote controller of an indoor unit from the other series is set as a master remote controller, cooling/heating switchover will be possible.

* If all indoor units are from the Connection unit series, an outdoor unit Cool/Heat selector will be needed to enable cooling/heating switchover.

* Group control between Connection Unit series equipment within one system is possible. However, group control with the other VRV indoor units is not possible.

Indoorunit


Sound level (230 V)

Casing

dBAmmDimensions (HXWXD)

kgMachine weight

40/35

Piping connectionsLiquidGas

Drain piping VP 20 (External Dia. 26/Internal Dia. 20)

25

White(10Y9/0.5)19/14

671/494cfm

165X895X895

9.5 (Flare)15.9 (Flare)

43/38

31

29/211,024/741

230X895X89544/39

31

32/231,130/812

230X895X895

mm

Note : Specifications are based on the following conditions ;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB.

(*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.•Equivalent piping length : 7.5 m•Level difference : 0 m•Capacity of indoor unit is only for reference. Actual capacity of indoor unit is based on the total capacity index. •Sound level : (FXUQ-MA) Anechoic chamber conversion value, measured at a point 1.5 m below the unit centre. During actual operation, these values are normally somewhat higher as a result of ambient conditions.

OUTDOOR UNITS

90.5

MODEL Constituent Units

RXYQ20PRY6/PAY6 RXYQ22PRY6/PAY6



63

329+329

(1,680X930X765)+(1,680X1,240X765)







RXYQ32PRY6/PAY6


90.0

Power supply 3 phase, 380–415V, 50Hz

R410A

Cooling capacity

Btu/h(*1)

(*1)kW

(*2)

kcal/h(*1)

Refrigerant

Motor output kW((1.4+4.5+4.5)X1)+((1.4+4.5+4.5)X1)

Machine weight kg

dB(A)

Dimensions(HXWXD) mm

m3/min

Capacity control

Heating capacity (*3)

Compressor

Sound level (*4)

%

kW

Btu/h

kcal/h

Air flow rate

Casing color

77,800

309,000

86,000

341,000

Hermetically sealed scroll type

Without (E): Ivory white (5Y7.5/1), With (E): Light camel (2.5Y6.5/1.5)

233+233

62

205+285

56.2

62

249+285

61.9

62

205+329

67.8

64

205+341

71.8

64

249+341

77.5

65

285+341

10062.5 69.0 75.0 81.5 88.0 94.0

5-1008-100 7-100 6-100 6-100 5-100 5-100

83.0

(1,680X1,240X765)+(1,680X1,240X765)

55.9 61.5 67.4 71.4 77.0 82.5

(3.8X1)+((2.5+4.5)X1)

((1.2+4.5)X1)+((2.5+4.5)X1)

(3.8X1)+((1.4+4.5+4.5)X1)

(3.8X1)+((3.0+4.5+4.5)X1)

((1.2+4.5)X1)+((3.0+4.5+4.5)X1)

((2.5+4.5)X1)+((3.0+4.5+4.5)X1)

48,300

192,000

53,200

211,000

58,300

231,000

61,700

250,000

66,700

264,000

71,400

283,000

53,800

213,000

59,300

235,000

64,500

256,000

70,100

278,000

75,700

300,000

80,800

321,000

180+233 185+233 180+233 180+239 185+239 233+239

19.1 (Brazing)

34.9 (Brazing)

Refrigerant oil charge

Piping connections Liquid pipe mm

Gas pipe mm

15.9 (Brazing)

28.6 (Brazing)

15.9 (Brazing)

28.6 (Brazing)

15.9 (Brazing)

34.9 (Brazing)

19.1 (Brazing)

34.9 (Brazing)

19.1 (Brazing)

34.9 (Brazing)

19.1 (Brazing)

34.9 (Brazing)

Refrigerant oilRefer to the nameplate of the compressor

Refrigerant charge kg 11.5+11.57.2+9.5 7.9+9.5 7.2+11.5 7.2+11.7 7.9+11.7 9.5+11.7

•Sound level : (*4) Anechoic chamber conversion value, measured at a point 1 m in front of the unit at a height of 1.5 m.


Notes : 1. Models with (E) feature components treated for heat and rust corrosionresistance, such as external panels, fan motor, and electric component box, in addition to the fins of the heat exchanger. These models are designed specifically for use in areas which are subject to salt damage and atmospheric pollution. Please contact Daikin for more information.

2. Specifications are based on the following conditions;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB. (*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.•Heating : (*3) Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.•(*1)(*2)(*3) Equivalent piping length : 7.5 m, level difference 0 m.

3. Please ensure to install ELCB (Earth Leakage Circuit Breaker) for above mentioned products to prevent ground fault effects. For details, please refer Note7. Field wiring of page 10 in installation manual which comes along with the product.

Normal Types (50 Hz)

Refrigerant

Motor output kW

Machine weight kg

dB(A)

Dimensions(HXWXD) mm

m3/min

Capacity control


Cooling capacity

Btu/h(*1)

Compressor

Sound level (*4)

(*1)

%

kW

Btu/h

kcal/h

kW(*2)

Air flow rate

Power supply

Casing color

R410A

4.5X1 3.8X1 (1.2+4.5)X1

205 205 249

57 57 58

1,680X635X765 1,680X930X765

180 180 185

285

60

233

20-100 20-100 14-100

18.0

61,400

15,500

25.0

85,300

21,500

31.5

107,000

27,100

16.1

55,000

13,900

22.5

76,800

19,400

28.2

96,200

24,300


(0.3+4.5+4.5)X1

329

60

233

16.0 22.4 28.0

14-100

37.5

128,000

32,300

33.7

115,000

29,000

33.5

10-100

45.0

154,000

38,700

40.2

137,000

34,600

40.0


3 phase, 380–415 V, 50 Hz

(2.5+4.5)X1

1,680X1,240X765

329

60

233

RXYQ6PAY16 RXYQ8PRY6/PAY6 RXYQ10PRY6/PAY6 RXYQ12PRY6/PAY6 RXYQ14PRY6/PAY6 RXYQ16PRY6/PAY6

10-100

50.0

171,000

43,000

45.3

155,000

39,000

45.0

(1.4+4.5+4.5)X1

341

63

239

RXYQ18PRY6/PAY6

9-100

56.5

193,000

48,600

49.3

168,000

42,400

49.0

(3.0+4.5+4.5)X1

MODEL

kcal/h(*1)

Refrigerant oil


9.5 (Brazing)

19.1 (Brazing)

9.5 (Brazing)

19.1 (Brazing)

9.5 (Brazing)

22.2 (Brazing)

12.7 (Brazing)

28.6 (Brazing)

12.7 (Brazing)

28.6 (Brazing)

12.7 (Brazing)

28.6 (Brazing)

15.9 (Brazing)

28.6 (Brazing)Piping connections Liquid pipe mm

Gas pipe mm

Refer to the nameplate of the compressor

Refrigerant charge kg 7.2 7.2 7.9 9.5 11.3 11.5 11.7

Specifications

39 40

3. Please ensure to install ELCB (Earth Leakage Circuit Breaker) for above mentioned products to prevent ground fault effects. For details, please refer Note7. Field wiring

of page 10 in installation manual which comes along with the product.

OUTDOOR UNITS

Normal Types (50 Hz)

65 66 65 64 65 67


R410A

Cooling capacity

Btu/h(*1)

(*1)kW

(*2)

kcal/h(*1)

Refrigerant

Motor output kW((1.4+4.5+4.5)X1)+((3.0+4.5+4.5)X1)

((3.0+4.5+4.5)X1)+((3.0+4.5+4.5)X1)

(3.8X1)+((2.5+4.5)X1)+((3.0+4.5+4.5)X1)

(3.8X1)+((1.4+4.5+4.5)X1)+((1.4+4.5+4.5)X1)

(3.8X1)+((1.4+4.5+4.5)X1)+((3.0+4.5+4.5)X1)

(3.8X1)+((3.0+4.5+4.5)X1)+((3.0+4.5+4.5)X1)

Machine weight kg

dB(A)

m3/min

Capacity control


Compressor

Sound level (*4)

%

kW

Btu/h

kcal/h

Air flow rate

Casing color

81,400

323,000

85,100

338,000

91,200

362,000

97,200

386,000

101,000

399,000

104,000

413,000

92,000

365,000

97,200

386,000

102,000

406,000

108,000

427,000

114,000

450,000

119,000

471,000


233+239 239+239 180+233+239 180+233+233 180+233+239 180+239+239

329+341 341+341 205+285+341 205+329+329 205+329+341 205+341+341

107

94.6

(1,680X1,240X765)+(1,680X1,240X765)

113

99.0

119

106

(1,680X930X765)+(1,680X1,240X765)+(1,680X1,240X765)

125

113

132

117

138

121

94.0 98.0 105 112 116 120

Dimensions(HXWXD)mm






RXYQ8PRY6/PAY6 RXYQ12PRY6/PAY6 RXYQ18PRY6/PAY6






5-100 4-100 4-100 4-100 4-100 4-100

67 67 67 67 68


R410A

Cooling capacity

Btu/h(*1)

(*1)kW

(*2)

kcal/h(*1)

Refrigerant

Motor output kW((1.2+4.5)X1)+((3.0+4.5+4.5)X1)+

((3.0+4.5+4.5)X1)

(1,680X930X765)+(1,680X1,240X

765)+(1,680X1,240X765)

((2.5+4.5)X1)+((3.0+4.5+4.5)X1)+((3.0+4.5+4.5)X1)

((0.3+4.5+4.5)X1)+((3.0+4.5+4.5)X1)+((3.0+4.5+4.5)X1)

((1.4+4.5+4.5)X1)+((3.0+4.5+4.5)X1)+((3.0+4.5+4.5)X1)

((3.0+4.5+4.5)X1)+((3.0+4.5+4.5)X1)+((3.0+4.5+4.5)X1)

kg

Machine weight kg

dB(A)

m3/min

Capacity control


Compressor

Sound level (*4)

%

kW

Btu/h

kcal/h

Air flow rate

Casing color

109,000

433,000

114,000

454,000

120,000

474,000

124,000

491,000

127,000

505,000

125,000

495,000

130,000

515,000

136,000

539,000

140,000

556,000

146,000

580,000


185+239+239 233+239+239 233+239+239 233+239+239 239+239+239

8.4+12.7+12.7 10.0+12.7+12.7 12.3+12.7+12.7 12.5+12.7+12.7 12.7+12.7+12.7

249+341+341 285+341+341 329+341+341 329+341+341 341+341+341

145

127

(1,680X1,240X765)+(1,680X1,240X765)+(1,680X1,240X765)

151

133

158

139

163

144

170

148

126 132 138 143 147

Dimensions(HXWXD)mm








RXYQ54PRY6/PAY6



3-100 3-100 3-100 3-100 3-100


19.1 (Brazing)

34.9 (Brazing)

19.1 (Brazing)

41.3 (Brazing)

19.1 (Brazing)

41.3 (Brazing)

19.1 (Brazing)

41.3 (Brazing)

19.1 (Brazing)

41.3 (Brazing)

19.1 (Brazing)

41.3 (Brazing)



Gas pipe mm


19.1 (Brazing)

41.3 (Brazing)

19.1 (Brazing)

41.3 (Brazing)

19.1 (Brazing)

41.3 (Brazing)

19.1 (Brazing)

41.3 (Brazing)

19.1 (Brazing)

41.3 (Brazing)



Gas pipe mm

Refrigerant charge kg 11.5+11.7 11.7+11.7 7.2+9.5+11.7 7.2+11.5+11.5 7.2+11.5+11.7 7.2+11.7+11.7

Refrigerant charge kg 7.9+11.7+11.7 9.5+11.7+11.7 11.3+11.7+11.7 11.5+11.7+11.7 11.7+11.7+11.7

•Heating : (*3) Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.•(*1)(*2)(*3) Equivalent piping length : 7.5 m, level difference 0 m.•Sound level : (*4) Anechoic chamber conversion value, measured at a point 1 m in front of

the unit at a height of 1.5 m. During actual operation, these values are normally somewhat higher as a

result of ambient conditions.

Notes : 1. Models with (E) feature components treated for heat and rust corrosionresistance, such as external panels, fan motor, and electric component box, in addition to the fins of the heat exchanger. These models are designed specifically for use in areas which are subject to salt damage and atmospheric pollution.Please contact Daikin for more information.

2. Specifications are based on the following conditions;•Cooling : (*1) Indoor temp. of 27°CDB, 19.5°CWB, and outdoor temp. of 35.0°CDB. (*2) Indoor temp. of 27°CDB, 19.0°CWB, and outdoor temp. of 35.0°CDB.

INDOOR UNITS

FXFQ25P FXFQ32P FXFQ40P FXFQ50P FXFQ63P FXFQ80P FXFQ100P FXFQ125P1

4

BYCP125K-W1

KAFP556H80 KAFP556H160KAFP557H80 KAFP557H160KAFP552H80 KAFP552H160KAFP553H80 KAFP553H160

KDTP55K160

KDJP55H160

Filter related

5 Fresh air intake kit

Decoration Panel2 KDBH55K160FSealing member of air discharge outlet3 KDBP55H160FAPanel spacer

High efficiency filter unit 65%High efficiency filter unit 90%Replacement high efficiency filter 65%Replacement high efficiency filter 90%Filter chamberLong life replacement filter Non-woven type

Chamber typeWithout T shape and fanWith T shape without fan

KDDFP55H160

Ultra long-life filterReplacement ultra long-life filter

Direct installation type

KAFP551K160KAFP55H160

KAFP55H160HKDDP55K160

KDDP55K160KKDDP55X160

No.

Ceiling Mounted Cassette (Round Flow) TypeType

Item

6 KDJP55H80Branch duct chamber7 KKSJ55K160Chamber connection kit8 KDTP55K80Insulation kit for high humidity

Ceiling Mounted Cassette (Compact Multi Flow) TypeNo.

1 Decoration panel2 Sealing member of air discharge outlet3 Panel spacer45 Fresh air intake kit

Replacement long-life filterDirect installation type

TypeItem

Remote controllerWired

8 Adaptor for wiring

9-1 Wiring adaptor for electrical appendices (1)


10 Remote sensor (for indoor temperature)

12 External control adaptor for outdoor unit

Wired remote controller with weekly schedule timer

11 Mounting plate for adaptor PCB

Wireless

7

6

FXZQ-MBYFQ60B8W1KDBHQ44B60KDBQ44B60KAFQ441B60KDDQ44X60

DTA104A62

BRC1D61

KRP4AA53

KRCS01-1B

BRC7E530W

Note 2KRP1B101

KRP1B57

KRP2A62

BRC1C62

Notes: 1. Mounting plate is necessary for each adaptor marked .2. Up to 2 mounting plates can be installed for each indoor unit.

Slim Ceiling Mounted Duct Type (900/1,100 mm width type)

No. FXDQ25PB FXDQ32PBFXDQ20PB

1 KDT25N32Insulation kit for high humidity

Slim Ceiling Mounted Duct Type (700 mm width type)Type

Item

No.

1 KDT25N50 KDT25N63Insulation kit for high humidity

TypeItem FXDQ63NBFXDQ50NBFXDQ40NB

Wall Mounted TypeFXAQ25PFXAQ20P

1 Drain pump kit K-KDU572EVE

FXAQ32P FXAQ40P FXAQ50P FXAQ63PNo. TypeItem

4241

Option List

INDOOR UNITS

MODEL FVYCP450MR FVYCP560MRRear-suction port kit

Suction port

Other

Front-suction port base flange

High-performance filter chamber

Front-suction high-performance filter chamber

Suction grille

Long-life filter

FVYCP280M9R

High efficiency filter

Replacement filter

Vibration isolation stand

Wooden stand

KDFJ905A280

KDDF-92A200

KDDF-93A200

KD-9A280

KDGF-9A280

KAF-91A280

KAF-92A280

KAF-93A280

KWF1G8P

K-ABSG1408A

KDFJ905A400

KDDF-92A400

KDDF-93A400

KD-9A400

KDGF-9A400

KAF-91A400

KAF-92A400

KAF-93A400

KKWJ9A400

K-ABSG1409A

KDFJ905A560

KDDF-92A560

KDDF-93A560

KD-9A560

KDGF-9A560

KAF-91A560

KAF-92A560

KAF-93A560

KWF1G15

K-ABSG1410A

No. FXMQ140PVE

2 Filter chamber

1 High efficiency filter65%

90%

KAF372AA160

KAF373AA160

KDDF37AA160

3 Long life replacement filter KAF371AA160

4 Long life filter chamber kit KAF375AA160

5 Service panel

KTBJ25K160W

KTBJ25K160F

KTBJ25K160T

6 Air discharge adaptor KDAJ25K140A

TypeItem

Notes: 1. Mounting plate is necessary for each adaptor marked .2. Up to 2 adaptors can be fixed for each mounting plate.3. Only one mounting plate can be installed for each indoor unit.4. For residential use only. Cannot be used with other centralised control equipment.

10

Remote controllerWireless

Wired




Remote controller for hotel use (Concealed type)


15 External control adaptor for outdoor unit

Simplified remote controller (Exposed type)

BRC4C65

14 Mounting plate for adaptor PCB

BRC3A61

BRC2C519

Wired remote controller with weekly schedule timer BRC1D618

7BRC1C62

KRP1C64

KRP2A61

KRP4AA51

Note 2,3KRP4A96

DTA104A61

KRCS01-4B

DCS302CA61Central remote controller17

Note 4DCS303A51Residential central remote controller16

DCS301BA61Unified ON/OFF controller19

KJB212AAElectrical box with earth terminal (2 blocks)20

KEK26-1ANoise filter (for electromagnetic interface use only)21

KJB311AAElectrical box with earth terminal (3 blocks)18

DST301BA61Schedule timer22

No.


FXMQ40PFXMQ50PFXMQ63PFXMQ80P

FXMQ100PFXMQ125P

FXMQ200MFXMQ250M

1 Drain pump kit

3 Filter chamber

KDU30L250VE—

2 High efficiency filterKAFJ372L280KAF372AA8065%

90%

KAF372AA160

KAFJ373L280KAF373AA80 KAF373AA160

KDJ3705L280KDDF37AA80 KDDF37AA160

4 Long life replacement filter KAFJ371L280KAF371AA80 KAF371AA160

5 Long life filter chamber kit KAFJ371L280KAF375AA80

KAF372AA56

KAF373AA56

KDDF37AA56

KAF371AA56

KAF375AA56

FXMQ20PFXMQ25PFXMQ32P

KAF372AA36

KAF373AA36

KDDF37AA36

KAF371AA36

KAF375AA36 KAF375AA160

6 Service panel—

KTBJ25K80WKTBJ25K56WKTBJ25K36W KTBJ25K160W

KTBJ25K80FKTBJ25K56FKTBJ25K36F KTBJ25K160F

KTBJ25K80TKTBJ25K56TKTBJ25K36T KTBJ25K160T

7 Air discharge adaptor KDAJ25K71AKDAJ25K56AKDAJ25K36A KDAJ25K140A

Type

Item


4443

Option List Option List

OUTDOOR UNITS

Normal Type

No.

1 Cool/Heat Selector

1-1 Fixing box

2REFNET header

REFNET joint

3 Outdoor unit multi connection piping kit

No.

1 Cool/Heat Selector

4

3

1-1 Fixing box

REFNET joint

5 Central drain pan kit

Pipe size reducer

REFNET header2

4 Central drain pan kit

5 Digital pressure gauge kit

KRC19–26A

KHRP26M22H (Max. 4 branch)KHRP26M33H (Max. 8 branch)

KHRP26M22H (Max. 4 branch), KHRP26M33H (Max. 8 branch)KHRP26M72H (Max. 8 branch)


— —

KJB111A

KHRP26A22T, KHRP26A33T, KHRP26A72TKHRP26A22T, KHRP26A33T

KWC26C280(E) KWC26C450(E)

BHGP26A1(E)

Outdoor unit multi connection piping kit

Distributivepiping

Distributivepiping

KJB111A

KHRP26A22T, KHRP26A33T, KHRP26A72T, KHRP26A73T

KHRP26M73TP, KHRP26M73HP—

RXYQ20PRY6/PAY6RXYQ22PRY6/PAY6

RXYQ24PRY6/PAY6RXYQ26PRY6/PAY6RXYQ28PRY6/PAY6


KWC26C280(E)KWC26C450(E)

KWC26C450(E)X2

BHFP22P100 BHFP22P151

6 Digital pressure gauge kit BHGP26A1(E)



KWC26C280(E)KWC26C450(E)X2

KWC26C450(E)X3

KRC19–26A

KHRP26M22H (Max. 4 branch), KHRP26M33H (Max. 8 branch)KHRP26M72H (Max. 8 branch), KHRP26M73H (Max. 8 branch)

KHRP26A22T, KHRP26A33TKHRP26A72T

KHRP26M22H (Max. 4 branch)KHRP26M33H (Max. 8 branch)KHRP26M72H (Max. 8 branch)

Type

Item

Type

Item

RXYQ6PAY16RXYQ8PRY6/PAY6RXYQ10PRY6/PAY6

INDOOR UNITS

Floor Standing TypeFXLQ20MA

1 Long life replacement filter

FXLQ25MA FXLQ32MA FXLQ40MA FXLQ50MA FXLQ63MA

KAFJ361K28 KAFJ361K45 KAFJ361K71

No. TypeItem


No.

1

2

Decoration PanelHigh efficiency filter 65% 1

High efficiency filter 90% 1

Long life replacement filter

Filter related bottom suction

FXCQ20MFXCQ25MFXCQ32M

FXCQ40M FXCQ50M FXCQ63M FXCQ80M FXCQ125M

KAFJ532G36 KAFJ532G56 KAFJ532G160KAFJ532G80KAFJ533G36 KAFJ533G56 KAFJ533G160KAFJ533G80KDDFJ53G36Filter chamber KDDFJ53G56 KDDFJ53G160KDDFJ53G80KAFJ531G36 KAFJ531G56 KAFJ531G160KAFJ531G80

Type

ItemBYBC32G-W1 BYBC50G-W1 BYBC125G-W1BYBC63G-W1

Note: 1 Filter chamber is required if installing high efficiency filter.

Ceiling Mounted Cassette Corner TypeNo. Type

Item FXKQ32MAFXKQ25MA FXKQ40MA FXKQ63MA

1

2

BYK45FJW1 BYK71FJW1KPBJ52F56W KPBJ52F80WKAFJ521F56 KAFJ521F80

K-HV7AW K-HV9AWKDBJ52F56W KDBJ52F80WKFDJ52FA56 KFDJ52FA80

Panel related

Air inlet and air discharge outlet related

Decoration PanelPanel SpacerLong life replacement filterAir discharge grilleAir discharge blind panelFlexible duct (with shutter)

Ceiling Suspended TypeFXHQ32MA

1 Drain pump kit

2 Replacement long-life filter (Resin net)

KDU50M60VE

KAFJ501D56

3 L-type piping kit (for upward direction) KHFP5M35

FXHQ63MA

KDU50M125VE

KAFJ501D80

KHFP5M63

FXHQ100MA

KAFJ501D112

No. TypeItem

Concealed Floor Standing TypeFXNQ20MA

1 Long life replacement filter

FXNQ25MA FXNQ32MA FXNQ40MA FXNQ50MA FXNQ63MA

KAFJ361K28 KAFJ361K45 KAFJ361K71

No. TypeItem

Ceiling Suspended Cassette TypeNo.

Replacement long-life filter12345

Sealing member of air discharge outlet (*1)

Decoration panel for air dischargeVertical flap kitL-shape piping kit

FXUQ71MAV1

KDBHJ49F80KDBTJ49F80KDGJ49F80

KHFP49M140

KDBHJ49F140KDBTJ49F140KDGJ49F140

FXUQ100MAV1 FXUQ125MAV1

KAFJ495F140

(*1): This option is necessary for setting up 2-way (opposing directional) airflow when the air conditioner is installed.Note:

TypeItem

4645

Control Systems

The same operation modes and settings as with wired remote controllers are possible.

A compact light receiver unit to be mounted into a wall or ceiling is included.

• A light receiver unit for a Ceiling Mounted Cassette (Round Flow, Double Flow) type, Ceiling Suspended type and Wall Mounted type is mounted into the indoor unit.

The remote controller has centralised its frequently used operation selectors and switches (on/off, operation mode, temperature setting and airflow volume), making itself suitable for use in hotel rooms or conference rooms.

The exposed type remote controller is fitted with a thermostat sensor.

Signal receiver unit(Separate type)

Wireless remote controller

The concealed-type remote controller smartly fits into a night table or console panel in a hotel room.

Exposed type(BRC2C51)

Concealed type(For hotel use)

(BRC3A61)

Wireless remote controller (Option)

Simple remote controller (Option)

Signal receiver unit(Installed type)

Signal receiver unit can be installed on the panel ex. Ceiling Mounted Cassette (Round Flow) type

FXFQ FXCQFXZQ FXKQ FXMQ FXHQ FXAQ FXL(N)Q FXUQFXDQ

Individual Control Systems

*Refer to page 49 for the name of each model.

Easier to read because LCD screen is larger.

Digital display lets you set temperature in 1°C units.

Lets you individually programme by timer the respective times for operation start and stop within a maximum of 72 hours.

Equipped with a thermostat sensor in the remote controller that makes possible more comfortable room temperature control.

Enables you to select cool/heat/fan operation mode with the indoor remote controller of your choice without using the cool/heat selector.

Constantly monitors malfunctions in the system for a min. of 40 items, and is equipped with a "self-diagnosis function" that lets you know by message immediately when a malfunction occurs.

Lets you carry out various field settings by remote controller.

Enables you to select the ventilation mode and the volume of the HRV.

The rubber switch and the oil-resisting resin casing have been adopted for durability.

* When the auto-swing function is not available, the message, THIS FUNCTION IS NOT AVAILABLE is displayed when the wind direction adjustment button is pressed.

Wired remote controller (Option)

BRC1C62

BRC1E61

Wired remote controller with weekly schedule timer (Option)

BRC1D61

24-hour clock function (1-hour backup for power failures)

Includes ventilation mode and airflow rate switching, the main functions of HRV series.

Programming function for each day of week.

Scheduling possible of start/stop and temperature limit (5 settings/day)

Programming can be enabled or disabled.

Copy function for programmed schedules.

Adds advanced functions to those of the above wired remote controller.

Notes: 1. Standard remote controllers (BRC1C62) not required.2. If the BRC1D61 is connected to the centralised remote controllers

(DCS303A51, DCS302CA61, DCS301BA61, DST301BA61), the schedule function is not available.

Wide variation of remote controllers for indoor unitsWide variation of remote controllers for indoor units

Navigation Wired Remote Controller (Option)

*Refer to page 55 for the name of each model.

Wired remote controller with weekly schedule timer (BRC1D61)

Wired remote controller (BRC1C62)

Navigation remote controller(Wired remote controller) (BRC1E61)

Wireless remote controller*(Installed signal receiver unit)

Simple remote controller(Exposed type) (BRC2C51)

Simple remote controller(Concealed type: for Hotel use) (BRC3A61)

Wireless remote controller*(Separate type signal receiver unit)

Control Systems

4847

Residential central remote controller* (Option)

Max. 16 groups of indoor units can be easily controlled with the large LCD panel.

Max. 16 groups (128 indoor units) controllable

Large backlit LCD panel for easy readability

ON/OFF, temperature settings and scheduling can be controlled individually for indoor units.

All indoor units can be turned on or off at once with “ALL” button.

Each group has a dedicated button for convenience.

Outside temperature display

Unified ON/OFF controller (Option)

Max. 16 groups of indoor units can be operated simultaneously/individually.


2 remote controllers can be used to control from 2 different places.

Operating status indication (Normal operation, Alarm)

Centralised control indication

Max. wiring length 1,000 m (Total: 2,000 m)

Compact size casing (Thickness: 16 mm)

Connectable with Central Remote controller, Schedule timer and BMS system

Schedule timer (Option)

Max. 128 indoor units can be operated as programmed schedule.

Max. 128 indoor units controllable

When used in combination with a central remote controller, a maximum of 8 weekly schedule

patterns can be set, while the central controller can be used to select desired zones. Up to 2

ON/OFF pairs can be set per day.

Max. 48 hours back up power supply


Compact size casing (Thickness: 16 mm)

Connectable with Central Remote controller, Unified ON/OFF controller and BMS system

Up to 64 groups of indoor units (128 units) can be centrally controlled.

Optional controllers for centralised control can be combined freely, and

system can be designed in accordance with building scale and purpose.

System integration with various air-conditioning peripheral

equipment such as HRV (Heat Reclaim Ventilation) is easy.

Wiring can be run up to a total length of 2 km, and adapts easily to

large-scale system expansion.

Centralised Control Systems

DCS303A51

DCS301BA61

DST301BA61

Central control adaptor kit (DTA107A55).

Central remote controller(DCS302CA61)

Up to 2 units connectable

Unified on/off controller(DCS301BA61)

Connection of up to 8 unitspossible

Schedule timer (DST301BA61)1 unit connection possible ; 8 weekly schedule control patterns possible

Forced shut-down input

Independent and centralised control of HRV is possible.

Unification adaptor for computerised control * (DCS302A52)

Interlink Building Management System (host computer monitor panel) also possible

6 cores 7 cores max.

Address setting of central control can be performed from the remote controller.

Group control of up to 16 units is possible (group control via automatic address setting)

System without remote control is also available.

Interface adaptor for SkyAir series (built-in indoor unit) (DTA102A52)

Connectable number of centralised control equipment

Central remotecontroller 2 units

Unified on /offcontroller 8 units

Schedule timer 1 unit

Max. 64 groups (zones) of indoor units can be controlled individually same as LCD Remote controller.


Max. 128 groups (128 indoor units) are controllable by using 2 central remote controllers,

which can control from 2 different places.

Zone control

Malfunction code display


Connectable with Unified ON/OFF controller, schedule timer and BMS system

Airflow volume and direction can be controlled individually for indoor units in each group operation.

Ventilation volume and mode can be controlled for Heat Reclaim Ventilation (HRV).

Up to 4 ON/OFF pairs can be set per day by connecting a schedule timer.

DCS302CA61

Wiring adaptorfor other air-conditioners (DTA103A51)

Outdoor-air processing unit can be connected.

• Certain indoor units limit the functions of some control systems.

Central remote controller (Option)

* For residential use only. Cannot be used with other centralised control equipment.

Control Systems

Control Systems

5049

Advanced Control Systems

FeaturesOne touch selection to total air comfort

Up to 2,560 groups (5,120 indoor units) can be controlled by one system

• Handy area settings simplify detailed management of VRV.• Display of floor plans enables a quick search of desired air conditioning units.• Operation history shows manner of control and origin in past operations of air conditioning

units.

Central control

• Remote access with a PC allows total air conditioning management using the same type of screens as those displayed in the intelligent Touch Manager.

• Authorised users can centrally control individual air conditioning units from their own computers.

Remote access

• VRVs are controlled automatically throughout the year by the schedule function.• Interlocking VRVs and other equipment enables easy automation of building facilities operation.• Setback adjusts temperature settings even when rooms are unoccupied.

Automatic control

• The Energy Navigator feature simplifies energy management by tracking energy consumption data and identifying inefficient operation.

Energy management

• Contact information of maintenance contractors can be registered and displayed.• E-mails are sent automatically to alert of malfunctions and potential trouble.• The intelligent Touch Manager can link to the Air Conditioning Network Service System for 24-

hour monitoring of operating conditions and status.

Troubleshooting

• A single intelligent Touch Manager can manage a small building or be expanded to handle medium- to large-sized buildings.

• Large building properties can also take advantage of the iTM integrator to link up and expand system up to 5 intelligent Touch Managers for integrated control.

Scalability

Air Conditioning Network Service System

Web Access

Web Access

LAN

Max. 50miTM plus adaptor line

Di/Pi port

Max. 500m

I/O expansion line

I/O System (Max. 30 modules)

iTM plus adaptor (Max. 7 adaptors)

I/O moduleI/O module I/O module

Lighting Pump Fan Sensor

InternetIntranet

system overview

Max. 64 groupsPhone line

LAN

Internal modem(option)

Fire alarm

Max. 200m

kWh meter

Di/Pi line

USB memory

line

DCM601A51

Daikin proudly introduces its new intelligent Touch Manager, a VRV system controller featuring an array of simple, useful system management functions for added value.

New

New

52

Ethernet

Local Controller

Please contact Daikin for compatibility with BMS system

Security Power supply facilityFire alarm

Lift Pump Lighting,etc

BMS

HRV

VRV System

Integrated control systems that recognise the trend of open control systems

Compatibility with BMS enhanced by utilising the international communication standards, BACnet® or LONWORKS®.

BTL Certification

PPD data (Optional Di board is required.)

ISO 16484-5 (Does not support IEEE 802.3 protocol for BACnet®)

Conformance class 3 (ASHRAE 135–1995)

Standard BACnet® Device B-ASC (ASHRAE 135–2001)

Up to 40 outdoor units and 256 indoor unit groups on one gateway. (optional adaptor)

XIF file for confirming of specifications of the units.

Connectable up to 10 outdoor units and 64 indoor unit groups.

DMS504B51 Interface for use in LONWORKS®

DMS502B51 Interface for use in BACnet®

Local dealers

I/F unit*4Automatic data transfer

Mainfunction informationby E-mail

INTERNETACC center

Maintenance services that boost profits and customer satisfactionAir Conditioning Network Service System

24 hour on-line diagnostic system Energy saving and extention of aircon operating life Maintenance management via A /C network service system reports Reliable service at shortest lead time

DMS502B51(Interface for use in BACnet®)

DMS504B51(Interface for use in LONWORKS

®)

BACnet® LONWORKS®Interface for and

*1. Model name varies upon the system size.

*2. BACnet® is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE).

*3. LONWORKS® is a registered trade mark of Echelon Corporation.

*4. For an I/F unit, one of the following can be selected: Local Controller, intelligent touch Controller, or intelligent touch Manager.

*5. Ethernet is a registered trademark of Xerox Corporation.

*6. Refer to the Options page for the name of each model.

*Note : Pulse type KWh Meter is necessary for energy navigator & PPD option function Pulse type KWh Meter has to be provided by customer for this option.

Input (Lights)

Input (Key signal -General purpose ADP)

Dio UnitDEC102A51

Dio UnitDEC102A51

System

Set temperature change command

OFFcommand

ACC center• Air Conditioning Network Service System

Pi Port

• Connection to power consumption meter when using power proportional distribution function. (Option)

RS-232CPublicphone line

Air Conditioning NetworkService System modemfor connections

• CSV output of power proportional distribution results (Option)

PCMCIAFlash

Memory

Remote monitor-ing and control

Mobile Phone PC

Troublereports

D -NET Plus AdaptorDCS601A52 (option)

Number of indoor units expanded from 64 to 128.

D -NET

Function 1

Function 2

Function 3 Function 4

Function 5

Function 6

System Components

Indoor UnitHRV

Control Systems

Advanced Control Systems

Communication functions in the user-friendly icon-based multilingual controller simplify centralised control of the VRV system.

51

Colour LCD touch panel icon display

Small manageable size

Simplified engineering

Multi language (English, French, Italian, German, Spanish and Chinese)

Yearly schedule

PPD (Power Proportinal Distribution function) (Option)

Auto heat/cool change-over

Temperature limitation

Enhanced history function

Air Conditioning Network Service System (Optional Maintenance Service)

Simple Interlock Function

Support for centralised control from elsewhere using a PC with a Web browser (Option)Function 1

Sending of e-mail alerts to a specified address when malfunctions occur (Option)Function 2

Built-in modem for connecting to Air Conditioning Network Service System (Option)Function 3

Function 4

Management of facilities/equipment other than A/C units (By adding Dio unit or Di unit)Function 5

Simple Interlock FunctionFunction 6

Doubling of number of connectable indoor units by adding a D -NET Plus Adaptor (Option)

5453

(DCM601A51)

BMS

(Obtain locally)

Wiring adaptorfor electrical appendices(KRP2A61/62/53)

Interface Adaptor for SkyAir Series(DTA102A52)

Central Control Adaptor Kit(DTA107A55)

Interface Adaptor for DIII-NET use(KRP928BB2S)

Central RemoteController(DCS302CA61)

(DCS601C51)

Schedule Timer(DST301BA61)

Unified ON/OFFController(DCS301BA61)

Unification adaptorfor computerised control(DCS302A52)

DIII-NET Line

BACnet®/Ethernet or LONWORKS®

Network Communication Line

Contact Signal Line

Caution: Limitation may apply to some models and functions. Please contact your local sales office for details. Consultation is necessary before employing this control system. Please contact your local sales office before making a purchase.

Air Conditioning Network Service System(There are restrictions in applicable areas and release times, therefore please consult us separately for details.)(Optional Maintenance Service)

Control /Connection Interface

Building Control System

Interface for use in BACnet®

(DMS502B51)

Interface for use in LONWORKS®

(DMS504B51)

ACC Centre

Di unit (DEC101A51)Dio unit (DEC102A51)

Building services equipment

• Electrical equipment• Supply water and drainage equipment• Automatic fire alarm• Parking equipment• Lift• Ventilation equipment• Lighting• Crime and fire prevention equipment

Integrated Building Monitoring System

Controllers for Centralised Control

The high speed transmission of DIII-NET enables more advanced control of the VRV system, providing you with enhanced comfort.

D -NET(High Speed Multiple

Transmission)

DIII-NET, Daikin’s unique high speed multiple transmission system, links air conditioners and various other building equipment—in accordance with applications, scale and conditions—and transmits vast amounts of information between them.

Note: BACnet® is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE). LONWORKS® is a trademark of Echelon Corporation registered in the United States and other countries.

Control Systems

The DIII-NET system provides for:• Close control and monitoring by integrating a wide variety of air-conditioners in the

entire building.• Saving the in-building cabling using non-polar, two-wire cables. Easier wiring work with

tremendously fewer wiring errors.• Additional setups readily up and running. An extendable cabling up to 2 km in total.• Different control equipment flexibly joined in the system for hierarchical risk

diversification.• Daikin's total heat exchangers and other devices under integral control.

VRV

Heat Reclaim Ventilator

SkyAir

Packaged Air-conditioner

Residential Air-conditioner

* No adaptor is required for the FHYCP-DVE and FAY(P)71L.

VRV

Via internet

Via internet

New

55

Option List

CONTROL SYSTEMS

System Configuration

Building Management System

Note 2

DCS302CA61Central remote controller2

Note 3

DCS303A51Residential central remote controller1

Note 2

DCS301BA61Unified ON/OFF controller3

KJB212AElectrical box with earth terminal (2 blocks)3-1

KEK26-1Noise filter (for electromagnetic interface use only)3-2

KJB311AElectrical box with earth terminal (3 blocks)2-1

DTA102A52Interface adaptor for SkyAir-series5

DTA107A556

DTA103A51Wiring adaptor for other air-conditioner7

No. Item Model No. Function

DTA109A51D -NET

Expander Adaptor8

KRP4A92Mounting plate8-1

For UAT(Y)-K(A),FD-K

For SkyAir, FD(Y)M-FA, FDY-KAFDYB-KA, FVY(P)J-A

Central control adaptor kit

Notes: 1. Installation box for adaptor must be obtained locally. 2. For FXUQ-MAV1, an interface adaptor (DTA102A52) for the SkyAir series is necessary. 3. For residential use only. Cannot be used with other centralised control equipment.

No. Item Model No. Function

KJB411A

1-1

1-4

1

Electrical box with earth terminal (4 blocks)

DCS601A521-1

DCS004A511-3

DCS601C51

DCS002C511-2

intelligent Touch

Controller

DIII-NET plus adaptor

Web

intelligent Touch Controller

PPD

Hardware

Hardware

Software

Basic

Option

Note 2

DST301BA61Schedule timer4

DMS504B514

3

DAM411B513-1

*2 Interface for use in LONWORKS®

DMS502B51*1 Interface for use in BACnet®

Optional DIII board

Con

tact

/ana

log

sign

al

DAM412B51Optional Di board3-2

Com

mun

icat

ion

line

Notes: *1. BACnet® is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE).

*2. LONWORKS® is a registered trade mark of Echelon Corporation. *3. Installation box for adaptor must be obtained locally.

5 •Interface between the central monitoring board and central control units.DCS302A52Unification adaptor forcomputerised control

Air Treatment Equipment Lineup

56

Componentsof Indoor Air Quality

Componentsof Indoor Air Quality

A recent trend rapidly gaining popularity is for air treatment to be required as well as air conditioning. Daikin’s Outdoor-Air Processing Unit can combine fresh air treatment and air conditioning, supplied from a single system. It adjusts the temperature of air from outdoors using a fixed discharge temperature control. Along with Outdoor-Air Processing Units, we also offer Heat Reclaim Ventilation (HRV) systems. The HRV VAM-GJ series units in particular have been praised for their compactness, energy conservation and extensive operation range of outdoor temperatures. This series provides higher enthalpy efficiency , due to the greatly enhanced performance of the thin film element. Furthermore, improved external static pressure offers more flexibility for installation. The HRV VKM-GAM series units, equipped with a DX-coil and a humidifier, provide further advanced features, such as temperature adjustment to suit conditions indoors and to prevent cold air from blowing on people directly during heating operation. The series also realises significant energy savings by exercising heat recovery.

Daikin’s air treatment systemscreating a higherair quality environment

Daikin’s air treatment systemscreating a higherair quality environment

Ventilation Humidification

Air Processing*

Ventilation Ventilation Humidification

Air Processing*

Humidification

Ventilation Humidification

Air Processing*

Air Processing*

Outdoor-AirProcessing Unit VKM-GAM Type VKM-GA Type VAM-GJ Type

Refrigerant Piping Connectable Not connectable

Wiring Connectable Connectable

After-cool &After-heat Control

Available Not available

—

— — —

Energy savings obtained

Fitted

Option Option

Air supply only Air supply & air exhaust

220-240 V, 50 Hz 220-240 V, 50 Hz

Heat Reclaim Ventilation

Connectionswith VRV III

Connectable

Connectable

Available

Heat Exchange Element Energy savings obtained

Humidifier

High Efficiency Filter Option

Ventilation System Air supply & air exhaust

Power Supply 220-240 V, 50 Hz

Airflow Rate 150 m3/h250 m3/h350 m3/h500 m3/h650 m3/h800 m3/h

1080 m3/h 1000 m3/h

500 m3/h

800 m3/h1000 m3/h

1680 m3/h 1500 m3/h

2100 m3/h2000 m3/h

*Refers to bringing outdoor air to near indoor temperature and delivering to a room.

1

2

For models: VAM150/250/350/650/800/1000/2000GJVEFor models: VAM150/350/500GJVE2

1

*Refers to bringing outdoor air to near indoor temperature and delivering to a room.

Operation Control System Optional Accessories

Notes: 1. Installation box is necessary for each adaptor marked .2. Up to 2 adaptors can be fixed for each installation box.

No.

3

4

Remote controllerWireless

Wired

Simplified remote controller (Exposed type)




Remote controller for hotel use (Concealed type)


9External control adaptor for outdoor unit (Must be installed on indoor units)

Type

Item

Wired remote controller with weekly schedule timer

8 Installation box for adaptor PCB

2

1

10 Adaptor for multi tenant

FXZQ-MFXFQ-P FXCQ-M FXKQ-MA FXDQ-PBFXDQ-NB FXAQ-P FXLQ-MA

FXNQ-MA

BRC7E530WBRC7F634 BRC7C62 BRC4C61 BRC7EA618

—

— —

—

BRC4C62BRC4C65

BRC3A61

BRC2C51

FXMQ-P

BRC4C65

BRC2C51

BRC3A61

FXUQ-MA

BRC7C528W

—

—

BRC1D61

FXHQ-MA

BRC7E63W

FXMQ-MA

BRC4C62

5. Installation box is necessary for second adaptor.6. Installation box is necessary for each adaptor.

BRC1C62/BRC1E61

3. Only one installation box can be installed for each indoor unit.4. Up to 2 installation boxes can be installed for each indoor unit.

KRP1B61

DTA104A61

KRCS01-1B KRCS01-1B

KRP1B57 KRP1C63

KRP2A61 KRP2A62 KRP2A62

KRP4AA51 KRP4AA53 KRP4AA53

KRP2A61

KRP1B61

DTA104A62 DTA104A62

Note 2,3KRP1B96 —Note 3

KRP1CA93Note 2,3KRP4A93

Note 2,3KRP1H98

KRP1C64KRP1B61

KRP2A61 KRP2A61KRP2A61

KRP4AA51 KRP4AA51KRP4AA51

KRP2A62 KRP2A61

KRP4AA52 KRP4AA51 KRP4AA51

Note 2,3KRP4A96— Note 4,6

KRP1BA101

DTA104A61

KRP2A62

—

KRP1B97

KRP4AA53

—DTA104A53DTA104A61 DTA104A61 DTA104A62 DTA104A61 DTA104A61DTA104A61

—KRP1C3

—

KRP1B61KRP1BA56

KRP2A53

KRP4A54

KRP1B61

KRP2A61

KRP4AA51

KRCS01-1BKRCS01-4B KRCS01-4B

—— DTA114A61

Note 5KRP4A91

•Additional 64 groups (10 outdoor units) is possible. Max. 7 iTM plus adaptors can be connected to intelligent Touch Manager.DCM601A52

•8 pairs based on a pair of On/Off input and abnormality input.DEC101A51Di unit2-5

DCM601A51 •Air-conditioning management system that can be controlled by touch screen.intelligent Touch Manager

DCM601A53 •Max. 5 intelligent Touch Managers can be integrated.iTM integrator

HardwareBasic

iTM plus adaptor

•Building energy consumption is visualised. Wasted air-conditioning energy can be found out.DCM008A51iTM energy navigator

•Power consumption of indoor units are calculated based on operation status of the indoor unit andoutdoor unit power consumption measured by kWh metre.DCM002A51iTM power proportional

distribution

2

2-2

2-1

2-4

2-3

Hardware

Software

Option

•4 pairs based on a pair of On/Off input and abnormality input.DEC102A51Dio unit2-6

intelligent Touch Manager

5857

•The unit introduces outdoor air and adjusts the outdoor air temperature via fixed discharge

temperature control, thereby reducing the air conditioning load.

* The system can operate with outdoor-air temperatures ranging from -5 to 43°C. Heating performance is somewhat adversely

affected when the outdoor-air temperature is 0°C or below.* When shipped from the factory, the thermostat is set at 18°C for cooling and 25°C for heating. The set temperature can be varied

within the range of 13–25°C during cooling operation, and 18–30°C during heating operation, in the local setting mode using

the wired remote controller. The temperature, however, is not displayed on the remote controller.

* While in machine protection mode and depending on outdoor air conditions, discharge air temperature may not be at the set temperature.

* The fan stops when operating in defrosting, oil returning and hot start operations. The fan also may stop due to mechanical protection control.

• Ceiling mounted duct units with three differing capacities are available. These can be connectedto VRV series outdoor units to meet a varietyof different requirements.

Airflow rateFXMQ125MFV1FXMQ200MFV1FXMQ250MFV1 2,100 m3/h

1,680 m3/h1,080 m3/h

• The "self-diagnosis function" indicates the occur-rence and nature of abnormalities in the systemby displaying codes on the remote controller.

• Optional equipment includes long-life filters.

• Compatible with outdoor temperatures from -5°C to 43°C.

Notes1. The data shown in the graph illustrates the supported operation ranges under

the following conditions.Indoor and Outdoor UnitEffective piping length: 7.5 mHeight differential: 0 m

2. The discharge temperature can be set using the remote controller. However, the actual temperature may not match the temperature setting under some circumstances due to the outdoor-air processing load or mechanical protection controls.

3. The system will not operate in fan mode when the outdoor air temperature is 5°C or below.

• High-performance filters with dust collection efficiencies (JIS calorimetry) of 90% and 65% are also available as options.

• As with the VRV system,a variety of control systems can be deployed, including remote control from distances of up to 500 m.

* Group control is not possible between this unit and standard type indoor units. Connect remote controllers to each unit.

Wired remote controller (option)

• A central control system compatible with the VRV system can be installed.

* It is not possible to change the discharge air temperature settings from the central control system.

* Do not associate this equipment into zones with standard indoor units,

as central control will not be possible.

Central remote controller (option)

• As with the VRV system, the equipment employs the "super wiring system" so that the wiring linking indoor and outdoor units can also be utilised for central control.

DCS302CA61

BRC1C62

Notes:* Linked control of the product and the HRV is not supported.

* This equipment is intended for the treatment of outdoor air only. It is not to be used for maintaining indoor air temperature. Install and use with standard indoor units. Be sure to position the air discharge openings of the product in positions where the airflow will not blow on people directly. When outdoor-air processing is in excess, the unit switches to thermo-off mode, and outdoor air flows into the room directly.

* For outdoor ducts, be sure to provide heat insulation to prevent condensation.

* Group control of the product and the standard indoor units is not supported. A separate remote controller should be connected to each individual unit.

* The system will not operate in fan mode when the outdoor air temperature is 5°C or below.

* If the product is allowed to operate 24 hours a day, maintenance (part replacement, etc.) must be performed periodically.

* Temperature setting and Power Proportional Distribution (PPD) are not possible even if the intelligent Touch Controller or the intelligent Manager III is installed.

* The remote controller wired to the outdoor-air processing unit must not be set as the master remote controller. Otherwise, when set to “Auto,” the operation mode will switch according to the outdoor air conditions, regardless of the indoor temperature.

–5 15 19 (33.5) 43

32

Usage Limitations

Supported Heating

Operation Range

FanOperation

Supported CoolingOperation Range

Outdoor Air T

emperature

(°CW

B)

100%

Rel

ative

Humid

ity

90%

Rel

ative

Hum

idity

20% Relative

Humidity

30% Relative Humidity


Combine fresh air treatmentand air conditioning,supplied from a single system.

Outdoor-Air Processing Uni t

FXMQ125MFV1, FXMQ200MFV1, FXMQ250MFV1

Model Names

Fresh air treatment and air conditioning can be achieved with a single system by using heat pump technology—without the usual troublesome air supply and air discharge balance design. Fan coil units for air conditioning andan outdoor-air processing unit can be connected to the same refrigerant line. The results are enhanced design flexibility and a significant reduction in total system costs.

Combination with VRV

Outdoor-Air Processing Unit

Indoor Unit Indoor Unit

VRV Series Outdoor Units

AirConditioning

OutdoorAir Supply

The following restrictions must be observed in order to maintain the indoor units connected to the same system.Connection Conditions

• When outdoor-air processing units are connected, the total connection capacity must be within 50% to 100% of that of the outdoor units.

• When outdoor-air processing units and standard indoor units are connected, the total connection capacity of the outdoor-air processing units must not exceed 30% of that of the outdoor units.

• Outdoor-air processing units can be used without indoor units.

• Connectable outdoor units: VRV and systems.

50 Hz onlyFor outdoor units of 6 HP and above

Air conditioning and outdoor air processing can be accomplished using a single system.

6059

STANDARD SPECIFICATIONS

OPTIONS

Indoor unitType Ceiling Mounted Duct TypeModel

Power supply

Air filter

Cooling capacity *1

Heating capacity *1

Product massSound level *3

kcal/h

FXMQ125MFV1 FXMQ200MFV1 FXMQ250MFV11-phase 220-240 V (also required for indoor units), 50 Hz

Indoor unitModel

Operation remote controllerFXMQ125MFV1 FXMQ200MFV1 FXMQ250MFV1

BRC1C62DCS302CA61DCS301BA61DST301BA61

KRP2A61KRP4AA51

12,000 19,300 24,100

7,700 12,000 15,000

380X118 28 35

185 225 205*2

9.5 (flare) 15.9 (flare) 19.1 (brazing) 22.2 (brazing)

KAFJ371L140 KAFJ371L280KAFJ372L140 KAFJ372L280KAFJ373L140 KAFJ373L280KDJ3705L140 KDJ3705L280

PS1B female thread86 12342 47

RXYQ8–54 PRY6/PAY6 RXYQ10–54 PRY6/PAY6

kcal/h

Dimensions (HXWXD) 470X744X1,100 470X1,380X1,100

Btu/h 47,800 76,400 95,500kW 14.0 22.4 28.0

30,400 47,400 59,400Btu/h8.9 13.9 17.4kW

mmCasing Galvanised steel plate

WXNumber of units

m3/min

Pa

Drain

mmmmmmkg

dB(A)

Motor output

Airflow rate635 988 1,236cfm

Fan

Refrigerantpiping

External static pressure *4

LiquidGas

Connectable outdoor units *5 *6

Operation range (Fan mode operation between 15 and 19°C)

CoolingHeating

Range of the discharge temperature *7CoolingHeating

Power consumption kW

Ope

ratio

n/co

ntro

lF

ilter

s

Central remote controller

Long-life replacement filterColorimetry method 65%Colorimetry method 90%

High-efficiency filter

Filter chamber *1

KRP1B61Adaptor for wiring KDU30L250VEDrain pump kit

Unified ON/OFF controllerSchedule timerWiring adaptor for electrical appendices (1)Wiring adaptor for electrical appendices (2)

Notes: *1. Filter chamber has a suction-type flange. (Main unit does not.)• Dimensions and weight of the equipment may vary depending on the options used.• Some options may not be usable due to the equipment installation conditions, so please confirm prior to ordering.• Some options may not be used in combination.• Operating sound may increase somewhat depending on the options used.

Notes: *1. Specifications are based on the following conditions;• Cooling: Outdoor temp. of 33°CDB, 28°CWB (68% RH), and discharge temp. of 18°CDB. • Heating: Outdoor temp. of 0°CDB, -2.9°CWB (50% RH), and discharge temp. of 25°CDB. • Equivalent reference piping length: 7.5 m (0 m horizontal) • At 220 V.

*2. An intake filter is not supplied, so be sure to install the optional long-life filter or high-efficiency filter.Please mount it in the duct system of the suction side. Select its colorimetric method (gravity method) 50% or more.

*3. Anechoic chamber conversion value, measured at a point 1.5 m downward from the unit center.These values (measured at 220 V) are normally somewhat higher during actual operation as a result of ambient conditions.

*4. Values measured at 220 V.*5. Within the range that the total capacity of indoor units is 50 to 100%, it is possible to connect to the outdoor unit.*6. It is not possible to connect to the 6 HP outdoor unit.*7. Local setting mode. Not displayed on the remote controller.• This equipment cannot be incorporated into the remote group control of the VRV system.

DIMENSIONS

*These diagrams are based on FXMQ200 and FXMQ250MFV1.

FXMQ200MFV1FXMQ125MFV1

Model Gas piping diameter 15.9

19.1 attached piping

Liquid piping diameter 9.5 9.5

Local connection piping size

1 Liquid pipe connection2 Gas pipe connection3 Drain piping connection4 Electric parts box5 Ground terminal6 Name plate

7 Power supply wiring connection8 Transmission wiring connection9 Hanger bracket

10 Discharge companion flange11 Water supply port12 Attached piping (Note. 1)

2

FXMQ250MFV1 22.2 attached piping 9.5

Table of dimensions

FXMQ200MFV1FXMQ125MFV1

Model A B C744 685 5X100=5001380 1296 11X100=1100

D20- 4.7 hole32- 4.7 hole

FXMQ250MFV1 1380 1296 11X100=1100 32- 4.7 hole(All around)

650

or m

ore

(Ser

vice

spa

ce)

Inspection hole 600 or more

1148

1100 or more(Service space)

App

rox.

150

910

C

AB

D

A View

3X10

0=30

0

50

470

Suction side (Note.2)

760

1100

613

2 51 4611Discharge side

30

3

B View

360

250

3X10

0=30

033

0

B View

390

30

296

25

630

5X100=500600

20- 7 hole(All around)

8

360

200

250

346

10-M5 hole(All around)

2X200=400

580

630

7

61

Notes:1. The attached piping in the diagram is for FXMQ200MFV1 and FXMQ250MFV1 only. The gas piping connection port ( in the diagram) has a different bore form with FXMQ125MFV1. 2. An air filter is not supplied with this unit. Be sure to mount an air filter in the suction side.[Use a filter with dust collection efficiency of at least 50% (gravimetric method). This is available as an option.]3. For outdoor ducts, be sure to provide heat insulation to prevent condensation.

FXMQ125MFV1

A View A View

1230

11X100=11001200

245

390

30

60

296

25

360

250

3X10

0=30

033

0

32- 7 hole(All around)

12

8

1004

5X200=1000


360

200

250

330

B View (For FXMQ250MFV1)

7

5X200=1000

1230

580

360

200

250

330


B View (For FXMQ200MFV1)

7

FXMQ200/250MFV1

FXMQ125/200/250MFV1


0.359 0.6380.548

6261

50 Hz only

Humidifier elementDX-coil(Direct expansion coil)

OA(Fresh air fromoutdoors)

SA(Supply airto room)

EA(Exhaust air to outdoors)

RA(Return airfrom room)

Air Supply Fan

Electronics Box(Control box)

Exhaust FanHeat Exchanger Elements

Damper

Damper Motor

DX-coilHumidifier element

30.6°C62% RH 27.4°C

63% RH

26°C50% RH

Integrally-formed liner

Indoor

SA

RA

Outdoor

32°C70% RH

Integrally-formed liner

Temperatureand humidity

RA

SA

Operation ofthe heat exchanger element

HEP Element(Anti-mould)

Integrated system includes ventilation and humidifying operations.Ventilation, cooling/heating and humidifying are possible with one remote controller.

Indoor unit with outdoor air treatmentHeating and cooling

+

+

heat recovery

humidifying

–5 0 5 10 15 20Dry bulb temperature (°CDB)

25 30 35 40

Rel

ativ

e hu

mid

ity (

%)

20

40

6080100

Effect of full heat exchangeEffect of full heat exchangeEffect of full heat exchange

Effect of full heat exchangeEffect of cooling

Outdoor air temperature in summer

Indoor temperature during heating

Indoor temperature during cooling

Outdoor air temperature in winter Effect of heatingEffect of heatingEffect of heating

Effect of humidification

Using outdoor air, the temperature can be brought near room temperature with minimal cooling capacity through the use of outdoor air.

Other features

Heatingby DX-Coil

Heat exchange

To the Outdoor 10.4 °C

Outdoor AirFrom the Outdoor 7°C

Structure of VKM series

From the Indoor 20°CReturn Air

To the Indoor 24.5°CSupply Air

HumidificationNatural Evaporating Pan Type Humidifier

Exhaust Air

The Outdoor air is heated from 16.6 °C to 36.5 °C with DX-coil, Natural Evaporating Pan Type Humidifier is passed and humidification capacity is improved.

36.5°C16.6°C

Outdoor Indoor

Heating and humidification process

(VKM100GAMV1)

Indoor units can be connected to up to 130% of the capacity of the outdoor units.

A compact unit packed with

Daikin’s cutting-edge technologies

Efficient outdoor air introduction

with heat exchanger and cooling/heating operation

DX-Coil: Heat Exchanger which heating or cooling the air by VRV outdoor unit’s refrigerant.

Humidification:5.4kg/h


The HRV lineup features the DX-coil in response torecently diversifying outdoor air introduction requirements.

VKM50GAMV1, VKM80GAMV1, VKM100GAMV1

With DX Coil & Humidifier Type

VKM50GAV1, VKM80GAV1, VKM100GAV1

With DX Coil Type

Model Names

HRV (VKM series) series introduces fresh outdoor air with minimum heat losses, while a wide variety of features respond to customer requirements.

Efficient outdoor air introduction is possible

Humidifier

DX-coil

High static pressure

The lineup includes models with a humidifier, in response to diversifying customer requirements. (VKM50/80/100GAMV1 only)

The HRV features DX-coil that contributes to the prevention of cold airflow hitting people directly during heating operation, due to the after-cool, after-heat operations done beforehand.

High external static pressure means enhanced design flexibility.

Air conditioning and outdoor air processing can be accomplished using a single system.

Heat Recla im Vent i lat ionwith DX-Coi l and Humidi f ier — VKM ser ies

Indoor Unit Indoor Unit

VRV Series Outdoor Units

Air-Conditioning AirAir

Supply

ReturnAir

HRV with DX Coil & Humidifier

Outdoor Air

Exhaust Air

6463

SPECIFICATIONS

Note: 1. Cooling and heating capacities are based on the following conditions. Fan is based on High and Ultra-high.The figures in the parenthesis indicate the heat reclaimed from the heat recovery ventilator.When calculating the capacity as indoor units, use the following figures:VKM50GAMV1/GV1: 3.5 kW, VKM80GAMV1/GV1: 5.6 kW, VKM100GAMV1/GV1: 7.0 kW

2. Indoor temperature: 27°C DB, 19°C WB, Outdoor temperature: 35°C DB3. Indoor temperature: 20°C DB, Outdoor temperature: 7°C DB, 6°C WB4. Humidifying capacity is based on the following conditions:

Indoor temperature: 20°C DB, 15°C WB, Outdoor temperature: 7°C DB, 6°C WB5. The operating sound measured at the point 1.5 m below the centre of the unit is converted to that measured

in an anechoic chambar built in accordance with the JIS C 1502 conditions. The actual operating sound varies depending on the surrounding conditions (near running unit’s sound, reflected sound and so on) and is normally higher than this value.For operation in a quiet room, it is required to take measures to lower the sound.

6. The noise level at the air discharge port is about 8–11 dB or higher than the unit’s operating sound.For operation in a quiet room, it is required to take measures to lower the sound.

7. Airflow rate can be changed over to Low mode or High mode.8. In case of holding full water in humidifier.9. OA: fresh air from outdoor. RA: return air from room.

10. Specifications, design and information here are subject to change without notice.11. Power consumption and efficiency depend on the above value of airflow rate. 12. Temperature exchange efficiency is the mean value for Cooling and Heating. Efficiency is measured under

the following condition: Ratio of rated external static pressure outdoor to indoor is kept constant at 7 to 1.

13. In heating operation, freezing of the outdoor unit’s coil increases. Heating capability decreases and the system goes into defrost operation. During defrost operation, the fans of the unit continues driving (factory setting). The purpose of this is to maintain the amount of ventilation and humidifying.

14. When connecting with a VRV system heat recovery outdoor unit and bringing the RA (exhaust gas intake) of this unit directly in from the ceiling, connect to a BS unit identical to the VRV indoor unit (master unit), and use group-linked operation. (See the Engineering Data for details.)

15 When connecting the indoor unit directly to the duct, always use the same system on the indoor unit as with the outdoor unit, perform group-linked operation, and make the direct duct connection settings from the remote controller. (Mode No. “17 (27)” – First code No. “5” – Second code No. “6”.) Also, do not connect to the outlet side of the indoor unit. Depending on the fan strength and static pressure, the unit might back up.

Feed clean water (city water, tap water or equivalent). Dirty water may clog the valve or cause dirt deposits in the water container, resulting in poor humidifier performance. (Never use any cooling tower water and heating-purpose water.)Also, if the supply water is hard water, use a water softener because of short life.* Life of humidifying element is about 3 years (4,000 hours) under the supply water conditions of

hardness: 150 mg/l. (Life of humidifying element is about 1 year (1,500 hours) under the supply water conditions of hardness: 400 mg/l.)Annual operating hours: 10 hours/day x 26 days/month x 5 months = 1,300 hours

Type VKM50GAMV1 VKM80GAMV1 VKM100GAMV1 VKM50GAV1 VKM80GAV1 VKM100GAV1

Refrigerant R-410A

Power Supply 1-phase, 220–240 V, 50 Hz

Airflow Rate & Static Pressure (Note 7)

Ultra-highAirflow rate (m3/h) 500 750 950

Static pressure (Pa) 160 140 110

HighAirflow rate (m3/h) 500 750 950


Low

Heat exchange mode

Bypass mode

Heat exchange mode

Bypass mode

Airflow rate (m3/h) 440 640 820


560

490

420

560

490

420

620

560

470

620

560

470

670

570

480

670

570

480

Fan Motor Type Sirroco Fan

Motor Output kW 0.280 � 2 0.280 � 2 0.280 � 2

Sound Level (Note 5)(220/230/240 V)

Ultra-high (dB) 37/37.5/38

35/35.5/36

32/33/34

37/37.5/38

35/35.5/36

32/33/34

38.5/39/40

36/37/37.5

33/34/35.5

38.5/39/40

36/37/37.5

33/34/35.5

39/39.5/40

37/37.5/38

34/34.5/35.5

39/39.5/40

37/37.5/38

34/34.5/35.5

High (dB)

Low (dB)

Ultra-high (dB)

High (dB)

Low (dB)

Humidification Capacity (Note 4) (kg/h) 2.7 4.0 5.4

Temp. Exchange Efficiency

Ultra-high (%) 76 78 74

High (%) 76 78 74

Low (%) 77.5 79 76.5

Enthalpy Exchange Efficiency (Cooling)

Ultra-high (%) 64 66 62

High (%) 64 66 62

Low (%) 67 68 66

Enthalpy Exchange Efficiency (Heating)

Ultra-high (%) 67 71 65

High (%) 67 71 65

Low (%) 69 73 69

Casing Galvanised Steel Plate

Insulating Material Self-Extinguishable Urethane Foam

Heat Exchanging System Air to Air Cross Flow Tot al Heat (Sensible + Latent Heat) Exchange

Heat Exchanger Element Specially Processed Nonflammable Paper

Air Filter Multidirectional Fibrous Fleece

0°C–40°C DB, 80%RH or less

-15°C–40°C DB, 80%RH or less

0°C–40°C DB, 80%RH or less

s

DX-coilCapacity

Cooling (Note 2) (kW)

Heating (Note 3) (kW)

Dimensions

Height (mm) 387 387 387

Width (mm) 1,764 1,764 1,764

Depth (mm) 832 1,214 1,214

500

180

500

150

440

110

560

490

420

560

490

420

0.280 � 2

38/38.5/39

36/36.5/37

33.5/34.5/35.5

38/38.5/39

36/36.5/37

33.5/34.5/35.5

—

76

76

77.5

64

64

67

67

67

69

750

170

750

120

640

80

620

560

470

620

560

470

0.280 � 2

40/41/41.5

37.5/38/39

34.5/36/37

40/41/41.5

37.5/38/39

34.5/36/37

—

78

78

79

66

66

68

71

71

73

950

150

950

100

820

70

670

570

480

670

570

480

0.280 � 2

40/40.5/41

38/38.5/39

35/36/36.5

40/40.5/41

38/38.5/39

35/36/36.5

—

74

74

76.5

62

62

66

65

65

69

2.8

3.2

387

1,764

832

96

2.8

3.2

4.5

5.0

5.6

6.4

4.5

5.0

387

1,764

1,214

109

—

5.6

6.4

387

1,764

1,214

114Machine Weight

Net (kg)

Gross (Note 8) (kg)

102

107

120

129

125

134

Around Unit

OA (Note 9)

RA (Note 9)

Unit Ambient Condition

RXYQ6–54PRY6/PAY6Connectable outdoor units

(mm)Connection Duct Diameter ø200 ø250 ø200 ø250

Ultra-high (W)

High (W)

Low (W)

Power Consumption

Ultra-high (W)

High (W)

Low (W)

DIMENSIONS

4-14 x 40 oval holeHanger bracket

Supply air to room

SA

Return air from room

RA

(For humidifier) *1Maintenance cover

(Natural evaporative type) *1Humidifier

Solenoid valve *1

EA

(Outdoor air)Fresh air from outdoors

Exhaust air to outdoors

OA

Control box

Maintenance Cover

Mor

e th

an 6

00

hatchInspection

hatchInspection

the air filters, fans (and humidifier)Maintenance space for the heat exchanger elements

140 (In case of ■600 inspection hatch)360 (In case of ■450 inspection hatch)

High efficiency filter (option)

Liquid pipe connectionAir filters

(PT3/4 male screw)

(ø12.7)

(ø6.4)

connectionGas pipe

Heat exchanger elements

Drain outlet

(ø6.4C1220T)Feed water connection port *1

of the heat exchanger elements.Note *1. VKM50/80/100GAMV1 only.

The high effciency filter (option) can be attached to the SA surface*(■450 or ■600) at the service side of filters and elements.Be sure to provide two inspection hatch.*The specification subject to change without notice.*

VKM50/80/100GA(M)V1

210

B

42

Supply air fan

160

250

150–

153

C

Damper plate

210

GK

1688387

235

60

10I

20

153 F

Feed water tank *1

D

130

E

160

144

A

28

102

Direct expansion coil

34

H

J

322

20

1764515

Exhaust air fan

94

VKM50GA(M)V1 VKM80/100GA(M)V1832A 1,214248B 439431C 622164D 183420E 592248F 439878G 1,262137H 89137I 89

JK


Remote controller

Wiring adaptor for electrical appendices

Unified ON/OFF controllerSchedule timer

For humidifier running ON signal outputFor heater control kit

BRC1C62 *1

DCS302CA61Residential central remote controller DCS303A51 *2

DCS301BA61DST301BA61

KRP2A61

KRP50-2BRP4A50

Item Applicable model

Con

trol

ling

devi

ce

PC

Boa

rd A

dapt

or

Centralised controlling device

Note: 1.2.3.4.5

Installation box is necessary for each adaptor marked . Up to 2 adaptors can be fixed for each installation box.Only one installation box can be installed for each indoor unit.Up to 2 installation boxes can be installed for each indoor unit.Installation box is necessary for second adaptor.

6.7.

Installation box is necessary for each adaptor.*1 Necessary when operating HRV (VKM) independently. When operating interlocked with other air

conditioners, use the remote controllers of the air conditioners.*2 For residential use only. When connected with HRV (VKM), you can only switch the power ON/OFF.

Cannot be used with other centralised control equipment.

VKM50/80/100GA(M)V1

Silencer

Air suction/Discharge grilleHigh efficiency filter

Flexible duct (1 m)Flexible duct (2 m)

VKM50GA(M)V1 VKM80GA(M)V1 VKM100GA(M)V1KDDM24B100

250 mmK-DGL200B

—K-DGL250B

200 250KAF241G80M KAF241G100M

Air filter for replacement KAF242G80M KAF242G100MK-FDS201C K-FDS251CK-FDS202C K-FDS252C

—Nominal pipe diameter (mm)

WhiteNominal pipe diameter (mm)

ItemApplicable model

Addi

tiona

l fun

ctio

n

OPTIONS


For wiringType (indoor unit of VRV)

Installation box for adaptor PCB

FXCQ-M FXKQ-MAFXFQ-P FXLQ-MA FXNQ-MA

KRP1B61 KRP1C63 KRP1B61Notes 2, 3KRP1B96

—Notes 2, 3KRP1H98

—

FXUQ-MA

—

KRP1B97

KRP1B61

FXDQ-PBFXDQ-NB

Notes 4, 6 KRP1BA101

KRP1B56

FXHQ-MA FXAQ-PFXMQ-P

—Notes 2, 3KRP4A96

KRP1B3Notes 2, 3KRP4A93

Note 3KRP1C93

FXMQ-MA

KRP1B61KRP1C64

—

6665

Exhaustheat

Exhaustheat

The indoor accumulated heat is discharged at night.This reduces the air conditioning load the next day thereby increasing efficiency.

Indoorunit

Indoorunit

Cold air

Generatedheat

Heat is discharged. The load is small so the temperature is rapidly reducedto a comfortable level.

*Interlocked operation with an air conditioner

Comfortable!Comfortable!Comfortable!

This unit recovers heat energy lost through ventilation and curbs room temperature changes caused by ventilation, thereby conserving energy and reducing the load on the air conditioning system.

Molecule of waterMiscellaneous gas CO2 molecule, etc.

Sheet structure

Outdoor

Exhaust air

SA

Indoor

RA(uncleanindoor air)

Outdoor air (fresh air)

Total heat exchange ventilation

Enthalpy efficiency drastically improved by employing newly developed ultra-thin film element! (VAM-GJ model)

Thickness ofthe partition sheet

Due to the thinner film…•Decreases the moisture resistance of the partition sheets drastically.

•Realises more space for extra layers in the element, resulting in increased effective area that supply and exhaust air can be exposed to.

Moisture absorption increased by approx. 10%!

Moisture exchange efficiency is greatly improved by using optimised thinner films and moisture-absorption materials in the element. Furthermore, miscellaneous gas barrier properties are maintained by decreasing the porosity in the moisture-absorption materials.

Automatically switches the ventilation mode (Total Heat Exchange Mode/Bypass Mode) according to the operating status of the air conditioner.

Auto-ventilation ModeChangeover Switching

Reduces air conditioning load by not running the HRV while air is still clean soon after the air conditioner is turned ON.

Pre-cool,Pre-heat Control

Air conditioning sensibleheat load reduced by

approx. 5%*2!

23% 6%

2%

• The air conditioning load reduction values are based on the following conditions;Application: Tokyo office buildingBuilding form: 2 floors above ground, 6 floors underground, floor area 2,100 m2

Personnel density: 0.25 person/m2

Ventilation volume: 25 m3/hIndoor air conditioning level: summer 25°C 50% RH, intermediate seasons 24°C 50%RH, winter 22°C 40% RHOperating time: 2745 hours (9 hours per day, approx. 25 days per month)Calculation method: simulation based on "MICRO-HASP/1982" of the JapanBuilding Mechanical and Electrical Engineers Association.

VAM-GJIndividual operation

Normalventilation fan

VAM-GJInterlocked operationwith air conditioner

Air

cond

ition

ing

load

red

uctio

n (%

)

20%

0%

Air Conditioning LoadReduced by Approximately 31%• The air conditioning load reduction values may vary according to weather and

other environmental conditions at the location of the machine's installation.

Nighttime free cooling operation is an energy-conserving function that works at night when air conditioners are off. By ventilating rooms containing office equipment that raises the room temperature, nighttime free cooling operation reduces the cooling load when air conditioners are turned on in the morning. It also alleviates feelings of discomfort in the morning caused by heat accumulated during the night.•Nighttime free cooling operation only works to cool and if connected to Building Multi or VRV systems. •Nighttime free cooling operation is set to “off” in the factory settings, so if you wish to use it, request your dealer to turn it on.

*1 This function can be operated only when interlocked with air conditioners.*2 Value is based on the following conditions:•Cooling operation performed from April to October.•Calculated for air conditioning sensible heat load only (latent heat load not included).

High-humidity air

Low-humidity air

Precise, thin-filmmaterial

Exhaust air

Supply air


Air conditioning load reduced by approximately 31%!

Nighttime free cooling operation*1

The HRV Creates a High-Quality Environment by Interlocking with the Air Conditioner

306 mm

Energy Conservation

Air conditioning load reduced by approximately 31%!With a height of just 306 mm, the unit easily fits in limited spaces, such as above ceilings.

-20 -10 0 10 20 30 40 50

50˚CDB-15˚CDB 50˚CDB-15˚CDB

**For VAM500GJVE

Heat Recla im Vent i lat ion — VAM ser ies

VAM150GJVE, VAM250GJVE, VAM350GJVE, VAM500GJVE, VAM650GJVE, VAM800GJVE, VAM1000GJVE, VAM1500GJVE, VAM2000GJVE

Model Names

Indoor unit

Daikin air conditioner

LCD remote controllerfor indoor unit

• Operating mode signal • Filter cleaning signal • Failure detection signal

• ON/OFF signal• Cooling/Heating mode signal• Set temperature signal• Ventilation signal• Humidifier ON/OFF signal

HRV

InterlockingInterlocking

Compact Equipment

Cold Climate Compatible

Standard operation at temperatures down to -15°C.

Improved Enthalpy Efficiency Higher External Static PressureEnhanced Energy Saving Functions

1

2

This VAM series provides higher enthalpy efficiency , due to the greatly enhanced performance of the thin film element. Furthermore, improved external static pressure offers more flexibility for installation. Along with these three outstanding improvements, Daikin’s exclusive function —nighttime free cooling operation—contributes to energy conservation and more comfortable space.

1

2

For models: VAM150/250/350/650/800/1000/2000GJVEFor models: VAM150/350/500GJVE2

1

OA(Fresh air fromoutdoors)

SA(Supply airto room)

EA(Exhaust air to outdoors)

RA(Return airfrom room)

67

Note: 1.2.3.

4.5.6.7.

8.

9.

10.

11.

Sound level is measured at 1.5m below the centre of the body. Airflow rate can be changed over to Low mode or High mode.Sound level is measured in an anechoic chamber.Sound level generally becomes greater than this value depending on the operating conditions, reflected sound, and peripheral noise.The sound level at the air discharge port is about 8 dB higher than the unit's sound level.The specifications, designs and information given here are subject to change without notice.Temperature Exchange Efficiency is the mean value between cooling and heating.Efficiency is measured under the following conditions:Ratio of rated external static pressure has been maintained as follows; outdoor side to indoor side = 7 to 1.In conformance with JIS standards (JIS B 8628), operating sound level is based on the value when one unit is operated, with the value converted for an anechoic chamber. This is transmission sound from the main unit, and does not include sound from the discharge grille. Thus it is normal for the sound to be louder than the indicated value when the unit is actually installed.Sound level from the discharge port causes the value to be approximately 8 dB (models with the airflow rate of less than 150 to 500 m3/h) to approximately 11 dB (models with the airflow rate of 650 m3/h or more) greater than the indicated value. Furthermore, fan rotation and noise from the discharge grille may increase depending on the on-site duct resistance conditions. Please consider noise countermeasures when installing the unit.With large models in particular (1500 and 2000 m3/h models), if the supply air (SA) grille is installed near the main unit, the noise of the main unit may be heard from the discharge grille via the duct, and this will result in a marked increase in noise. In such cases, if peripheral effects are included (such as reverberation of the floor and walls, combination with other equipment, and background noise), sound level may be as much as 15 dB higher than the indicated value. When installing a large model, please provide as much separation as possible between the main unit and the discharge grille. If the equipment and discharge grille are near each other, please consider countermeasures such as the following:•Use a sound-muffling box, flexible duct and sound-muffling air supply/discharge grilles•Decentralised installation of discharge grillesWhen installing in a location with particularly low background noise such as a classroom, please consider the following measures to avoid transmission sound from the main unit:•Use of ceiling materials with high sound insulating properties (high transmission loss)•Methods of blocking sound transmission, for example, by adding sound insulating materials around the bottom of the sound source.Alternatively, consider supplementary methods such as installing the equipment in a different location (corridor, etc.)

Models VAM150GJVE VAM250GJVE VAM350GJVE VAM500GJVE

Temp. Exchange Efficiency (%)[50 Hz]

Ultra-High

High

84 79

79 75

79 75

79 74

79 74

75 72

75 72

78 72

78 72

77

77

82 80

For HeatingEnthalpy ExchangeEfficiency (%)[50 Hz]

For Cooling

Low

72 71 70 67Ultra-High

72 71 70 67High

76 74 77 74Low

66 63 66 55Ultra-High

66 63 66 55High

70 66 70 59Low

HeatExchangeModeSound Level

dB(A)[50 Hz]

BypassMode

27-28.5 27-29 31.5-33 33-35.5Ultra-High

26-27.5 26-27.5 30-31.5 31.5-34High

20.5-21.5 21-22 23-25 25-28.5Low

28.5-29.5 28.5-30.5 33-34.5 34.5-36Ultra-High

27.5-28.5 27.5-29 31.5-33 33-34.5High

22.5-23.5


22.5-23 24.5-26.5 25.5-28.5Low

150 250 350 500Ultra-High

150 250 350 500High

100 155 230 320Low

278X810X551 306X879X800mm

24 32kg

Casing

1-phase, 220-240 V/ 220 V, 50 HzPower Supply

Self-extinguishable polyurethane foamInsulation Material

Air to air cross flow total heat (Sensible heat + latent heat) exchangeHeat Exchange System

Specially processed nonflammable paperHeat Exchange Element Material

Multidirectional fibrous fleecesAir Filter

Sirroco fanType

Fan

Dimensions (HXWXD)

Machine Weight

0.030X2 0.090X2kW

100 150 200mm

Unit ambient condition

Motor Output

Connection Duct Diameter

Airflow Rate (m3/h)[50 Hz]

120 70 169 105Ultra-High

106 54 141 66High

56 24 67 32Low

External Static Pressure (Pa)[50 Hz]

VAM650GJVE VAM800GJVE VAM1000GJVE VAM1500GJVE

77 74 80.5 75.5

67.5 65 70 65

67.5 65 70 65

71.5 67.5 72.5 67

61 61 64 61

61 61 64 61

64 64 68.5 64

34-36 39-40.5 39.5-41.5 39.5-41.5

33-34.5 37-39.5 37.5-39.5 37.5-39.5

27.5-29.5 35-37.5 35-37.5 35-37.5

35-37.5 40.5-42 40.5-42.5 41-43

33-35.5 38.5-40 38.5-40.5 39.5-41

27.5-30.5 36-38.5 36-38.5 36.5-38

650 800 1,000 1,500

650 800 1,000 1,5000

500 700 860 1,320

387X1,111X1,214387X1,111X832338X973X832

45 55 67

785X1,619X832 785X1,619X1,214

129

0.140X2 0.280X2 0.280X4

250 350

85 133 168 112

53 92 110 73

35 72 85 56

VAM2000GJVE

79

72

72

75

62

62

66

41.5-43.5

39-43

36-39

43-45.5

40.5-45

37.5-39.5

2,000

2,000

1,720

157

116

58

45

SPECIFICATIONS


68

For wiring

Option List

Silencer

VAM150GJVE VAM250GJVE VAM350GJVE VAM500GJVE VAM650GJVE VAM800GJVE VAM1000GJVE VAM1500GJVE VAM2000GJVEKDDM24B50 KDDM24B100 KDDM24A100X2

200 250

Air suction/discharge grille (Obtain locally)

Branch duct(Obtain locally)

SA

SA

RA

EAOA

Duct(Obtain locally)

Flexible duct(Option)

Silencer (Option)

Round hood(Obtain locally)

Thermal insulation material (Obtain locally)

High efficient filter(Option)

Nominal pipe diameter (mm)

ItemApplicable model

Add

ition

alfu

nctio

n


HRV remote controller

Wiring adaptor for electrical appendices


Type (indoor unit of VRV)


Unified ON/OFF controllerSchedule timer

For humidifier

For heater control kit

BRC301B61

DCS302CA61Residential central remote controller DCS303A51 *1

DCS301BA61DST301BA61

KRP2A61

KRP50-2

BRP4A50KRP50-2A90 (Mounted electric component assy of HRV)

Item Applicable model

Con

trol

ling

devi

ce

PC

Boa

rd A

dapt

or

Centralised controlling device

Note: 1.2.34.

Installation box is necessary for each adaptor marked . Up to 2 adaptors can be fixed for each installation box.Only one installation box can be installed for each indoor unit.Up to 2 installation boxes can be installed for each indoor unit.

High efficiency filter

Flexible duct (1m)Flexible duct (2m)

Duct adaptor

KAF242G25M KAF242G50M KAF242G65M KAF242G80MKAF241G65M KAF241G80M

KAF242G100M KAF242G80MX2 KAF242G100MX2Air filter for replacement KAF241G25M KAF241G50M KAF241G100M KAF241G80MX2 KAF241G100MX2

K-FDS101C K-FDS151C K-FDS201C K-FDS251CK-FDS102C K-FDS152C K-FDS202C K-FDS252C

YDFA25A1 250Nominal pipe diameter (mm)

5.67.

Installation box is necessary for second adaptor.Installation box is necessary for each adaptor. *1 For residential use only. When connected with HRV (VAM), you can only switch

the power ON/OFF. Cannot be used with other centralised control equipment.

OPTIONS

EA

OA

RA

SA

Power supply (Obtain locally)Relay box

HRV

Heater(Obtain locally)

BRP4A50

Indoor Outdoor

When the installation of an electric heater is required in a cold region, this adaptor with an internal timer function eliminates the complicated timer connecting work that was necessary with conventional heaters.

Examine fully an installation place and specification for using the electric heater based on the standard and regulation of each country.

Supply the electric heater and safety production devices such as a relay and a thermostat, etc of which qualities satisfy the standerd and regulation of each country at site.

Use a non-inflammable connecting duct to the electric heater. Be sure to allow 2 m or more between the electric heater and HRV for safty.

For the HRV units, use a different power supply from that of the electric heater and install a circuit breaker for each.

Notes when installing

PC board adaptor for heater control kit (BRP4A50)

FXCQ-M FXKQ-MAFXFQ-P FXHQ-MA FXAQ-P FXLQ-MA FXNQ-MA

FXMQ-P

KRP1B61 KRP1C63 KRP1B61Notes 2, 3KRP1B96

Notes 2, 3KRP1H98

Notes 2, 3KRP4A96

KRP1B3

FXUQ-MA

KRP1B97Notes 2, 3KRP4A93

Note 3KRP1C93

FXMQ-MA

KRP1B61KRP1C64KRP1B61

FXDQ-PFXDQ-N(A)

Notes 4, 6KRP1B101

KRP1B56

HEAT PUMP - Air Freeze Corp · HEAT PUMP Heat Pump 50 Hz DAIPL-12F The specifications, designs, and...

Documents

Transcript of HEAT PUMP - Air Freeze Corp · HEAT PUMP Heat Pump 50 Hz DAIPL-12F The specifications, designs, and...