Heat Exchanger_Report
-
Upload
nitesh-kamerkar -
Category
Documents
-
view
41 -
download
1
Transcript of Heat Exchanger_Report
HEAT EXCHANGER Nitesh Dattaram Kamerkar
INTRODUCTION
FUNCTIONING
CLASSIFICATIONS
APPLICATIONS
CHALLENGES
Overview of
Heat
Exchanger
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 1
HEAT TRASFER o People have always understood that something flows from hot objects to cold ones.
We call that flow “heat”. o The flow of the heat is all-pervasive. It is active to some degree or another in
everything. Heat flows constantly from our bloodstream to the air around us. Such
processes go on in all plant, animal life and in the air around us. They occur
throughout the earth, which is hot at its core and cooled around its surface. o Heat transfer describes the exchange of thermal energy, between physical systems
depending on the temperature and pressure, by dissipating heat.
o The exchange of kinetic energy of particles through the boundary between two
systems which are at different temperatures from each other or from their
surroundings. Heat transfer always occurs from a region of high temperature to
another region of lower temperature.
o Heat transfer changes the internal energy of both systems involved according to the
First Law of Thermodynamics. The Second Law of Thermodynamics defines the
concept of thermodynamic entropy, by measurable heat transfer.
o Thermal equilibrium is reached when all involved bodies and the surroundings reach
the same temperature. Thermal expansion is the tendency of matter to change in
volume in response to a change in temperature.
o The fundamental modes of heat transfer are conduction or diffusion, convection and
radiation.
VARIOUS MODES OF HEAT TRANSFER ARE AS FOLLOWS:-
CONDUCTION
o Conduction through a medium
- Solid, like aluminum or steel
- Gas, like still air or water.
o Occurs in fins and tubes of heat exchangers.
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 2
CONVECTION
o From flowing fluid to a surface
- Flow may be due to pump, fan and motion of vehicle or
buoyancy driven. - Convection coefficients determined by analysis for simple
geometries or by test for most applications.
o Occurs from the fluid to the fins and tubes of heat
exchangers.
RADIATION
o From one surface to another
- Radiation in infrared wavelengths.
- Highly dependent on surface properties
o Generally small (ignored) in most heat exchanger applications.
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 3
FUNCTION OF HEAT EXCHANGER o A heat exchanger is a device that is used to transfer thermal energy (enthalpy)
between two or more fluids, between a solid surface and a fluid, or between solid
particulates and a fluid, at different temperatures and in thermal contact.
o In heat exchangers, there are usually no external heat and work interactions. Typical
applications involve heating or cooling of a fluid stream of concern and evaporation
or condensation of single- or multi component fluid streams.
o In other applications, the objective may be to recover or reject heat, or sterilize,
pasteurize, fractionate, distill, concentrate, crystallize, or control a process fluid.
o In a few heat exchangers, the fluids exchanging heat are in direct contact.
o In most heat exchangers, heat transfer between fluids takes place through a
separating wall or into and out of a wall in a transient manner.
o In many heat exchangers, the fluids are separated by a heat transfer surface, and
ideally they do not mix or leak. Such exchangers are referred to as direct transfer
type, or simply recuperators.
o In contrast, exchangers in which there is intermittent heat exchange between the hot
and cold fluids—via thermal energy storage and release through the exchanger
surface or matrix—are referred to as indirect transfer type, or simply regenerators.
Such exchangers usually have fluid leakage from one fluid stream to the other, due
to pressure differences and matrix rotation/valve switching. Common examples of
heat exchangers are shell-and tube exchangers, automobile radiators, condensers,
evaporators, air pre-heaters, and cooling towers.
o If no phase change occurs in any of the fluids in the exchanger, it is sometimes
referred to as a sensible heat exchanger. There could be internal thermal energy
sources in the exchangers, such as in electric heaters and nuclear fuel elements.
o Combustion and chemical reaction may take place within the exchanger, such as in
boilers, fired heaters, and fluidized-bed exchangers.
o Mechanical devices may be used in some exchangers such as in scraped surface
exchangers, agitated vessels, and stirred tank reactors. Heat transfer in the
separating wall of a recuperator generally takes place by conduction.
o However, in a heat pipe heat exchanger, the heat pipe not only acts as a separating
wall, but also facilitates the transfer of heat by condensation, evaporation, and
conduction of the working fluid inside the heat pipe. In general, if the fluids are
immiscible, the separating wall may be eliminated, and the interface between the
fluids replaces a heat transfer surface, as in a direct-contact heat exchanger.
o Heat Exchangers are widely used in space heating, refrigeration, air
conditioning, power plants, chemical plants, petrochemical plants, petroleum
refineries, natural gas processing, and sewage treatment.
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 4
CLASSIFICATIONS OF HEAT EXCHANGER1
CLASSIFICATION ACCORDING TO TRANSFER PROCESS :-
- Indirect contact type
Direct transfer type
1. Single phase
2. Multiphase
Storage type
Fluidized Bed
- Direct contact type
Immiscible fluids
Gas - liquid
Liquid – vapor
CLASSIFICATION ACCORDING TO NUMBER OF FLUIDS:-
- Two – fluids
- Three – fluids
- N – fluids (N > 3)
CLASSIFICATION ACCORDING TO SURFACE COMPACTNESS :-
- Gas –to- fluid
1. Compact (β ≥ 700 m2/m3)
2. Non compact (β < 700 m2/m3)
- Liquid –to- liquid and phase change
1. Compact (β ≥ 400 m2/m3)
2. Non compact (β < 400 m2/m3)
CLASSIFICATION ACCORDING TO CONSTRUCTION :-
- TUBULAR
Double-pipe
Shell-and-tube 1. Cross flow to tubes
2. Parallel flow to tubes
1Classification of heat exchangers (Shah, 1981)
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 5
Spiral Tube
Pipe coils
- PLATE TYPE
PHE (Plate Heat Exchanger)
1. Gasketed 2. Welded
3. Brazed
Spiral
Plate coil
Printed Circuit
- EXTENDED SURFACE
Plate – fin
Tube – fin 1. Ordinary separating wall
2. Heat – pipe wall
- REGENERATIVE
Rotary
Fixed – matrix
Rotary hoods
CLASSIFICATION ACCORDING TO FLOW ARRANGEMENTS:-
- Single – pass
1. Counter flow
2. Parallel flow
3. Cross flow
4. Split-flow
5. Divided-flow
- Multipass
Extended surface
1. Cross- counter flow
2. Cross- parallel flow
3. Compound flow
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 6
Shell-and-tube
1. Parallel counter flow
a. m- shell passes
b. n- tube passes
2. Split- flow
3. Divided- flow
- Plate
Fluid 1 m passes
Fluid 2 n passes
CLASSIFICATION ACCORDING TO HEAT TRANSFER MECHANISMS:-
Single- phase convection on both sides
Single- phase convection on one side, two- phase convection on other side
Two- phase convection on both sides
Combined convection and radiative heat transfer
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 7
TERMINOLOGY USED IN HEAT EXCHANGERS
TERMINOLOGY DEFINITION UNIT
Capacity Ratio Ratio of the products of mass flow rate and specific heat capacity
of the cold fluid to that of the hot fluid. Also computed by the ratio
of temperature range of the hot fluid to that of the cold fluid.
Higher the ratio greater will be size of the exchanger
Density It is the mass per unit volume of a material kg/m3
Effectiveness Ratio of the cold fluid temperature range to that of the inlet
temperature difference of the hot and cold fluid. Higher the ratio
lesser will be requirement of heat transfer surface
Fouling The phenomenon of formation and development of scales and
deposits over the heat transfer surface diminishing the heat flux.
The process of fouling will get indicated by the increase in pressure
drop
Fouling Factor The reciprocal of heat transfer coefficient of the dirt formed in the
heat exchange process. Higher the factor lesser will be the overall
heat transfer coefficient.
(m2.K)/W
Heat Duty The capacity of the heat exchanger equipment expressed in terms
of heat transfer rate, viz. magnitude of energy or heat transferred
per time. It means the exchanger is capable of performing at this
capacity in the given system
W
Heat exchanger Refers to the nomenclature of equipment designed and
constructed to transmit heat content (enthalpy or energy) of a
comparatively high temperature hot fluid to a lower temperature
cold fluid wherein the temperature of the hot fluid
decreases (or remain constant in case of losing latent heat of
condensation) and the temperature of the cold fluid increases (or
remain constant in case of gaining latent heat of vaporization). A
heat exchanger will normally provide indirect contact heating. E.g.
A cooling tower cannot be called a heat exchanger where water
is cooled by direct contact with air
Heat Flux The rate of heat transfer per unit surface of a heat
Exchanger
W/ m2
Individual Heat
transfer
Coefficient
The heat flux per unit temperature difference across Heat transfer
boundary layer of the hot / cold fluid film formed at the heat
transfer surface. The magnitude of heat transfer coefficient
indicates the ability of heat conductivity of the given fluid. It
increases with increase in density, velocity, specific heat, geometry
of the film forming surface
W/( m2.K)
LMTD
Correction
factor
Calculated considering the Capacity and effectiveness of a heat
exchanging process. When multiplied with LMTD gives the
corrected LMTD thus accounting for the temperature driving force
for the cross flow pattern as applicable inside the exchanger
Logarithmic
Mean
Temperature
difference
(LMTD)
The logarithmic average of the terminal temperature approaches
across a heat exchanger
°C
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 8
Overall Heat
transfer
Coefficient
The ratio of heat flux per unit difference in approach across a heat
exchange equipment considering the individual coefficient and
heat exchanger metal surface conductivity. The magnitude
indicates the ability of heat transfer for a given surface. Higher the
coefficient lesser will be the heat transfer surface requirement
W/(m2.K)
Pressure drop The difference in pressure between the inlet and
outlet of a heat exchanger
Bar
Specific heat
capacity
The heat content per unit weight of any material per degree
raise/fall in temperature
J/(kg.K)
Temperature
Approach
The difference in the temperature between the hot and cold fluids
at the inlet / outlet of the heat exchanger. The greater the
difference greater will be heat transfer flux
°C
Thermal
Conductivity
The rate of heat transfer by conduction though any substance
across a distance per unit temperature difference
W/(m2.K)
Viscosity The force on unit volume of any material that will cause per
velocity
Pa (Pascal)
TEMA DESIGNATIONS OF HEAT EXCHANGERS
Because of the number of variations in mechanical designs for front and rear heads and
shells, and for commercial reasons,The Tubular Exchanger Manufacturers
Association(TEMA) has designated a system of notations that correspond to each major
type of front head, shell style and rear head. The first letter identifies the front head, the
second letter identifies the shell type and the third letter identifies the rear head type.
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 9
SIGNIFICANT INDUSTRIES IN WHICH HEAT EXCHANGERS ARE USED
EXTENSIVE HVACR { Heating- Ventilation- Air Conditioning- Refrigeration}
Heat transfer is one of the most important industrial processes. Throughout any industrial
facility, heat must be efficiently added, removed or moved from one process stream to
another. In massive organizations human comfort is the big thing to tackle with in order to
obtain maximum output from their employees. For employee’s comfort all industries no
matter whether it’s small or big, install HVACR (Heat- Ventilation- Air Conditioning-
Refrigeration).
Typical Applications are:-
o Community heating
o District heating
o Geothermal heating
o Solar heating
o Steam heating
o Swimming pool heating
o Tap water heating
o Condenser protection
o District cooling
o Free cooling
o Glycol saving
o Pressure breaker
o Thermal storage
POWER INDUSTRY
As we already mentioned Heat transfer is one of the most important industrial processes
so be it power generation from coal power plant, oil power plant or gas power plant. In
power industry we burn the fuel- coal, oil or gas in order to generate heat and then that
heat is used to run the turbine and power our houses. During the whole process a lot of
heat losses occur. To minimize that heat loss & in other way to optimize great yield
output, heat exchangers plays major role at various stages of energy conversion process.
In fact Boilers are one kind of heat exchanger. Apart from Boilers many more type of
heat exchangers are used in Power Industry.
FOOD & AGRICULTURE
Heat exchangers are extensively used for drying process involved in Food & Agriculture.
Achieving the desired taste, a stable shelf life and commercial sterility of food products is
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 10
reliant upon tight control of process timing and temperatures as well as careful and
correct raw ingredients and materials.
Typical Applications are:-
o Wide ranges of gums are used throughout the food industry. These can consist of
hydrocolloids, biopolymers and pectins. Heat exchangers work hard to tackle the
tough challenges of processing gums.
o The overall economy of sugar production is heavily reliant upon the cost of
energy. Plate heat exchanger and plate evaporator help sugar producers to
maximize product quality and minimize operating and energy costs.
o Purpose-built plate or tubular heat exchangers decrease energy consumption in
dairy processing. And whether it’s processing of milk, long-life products, cultured
products, ice cream, cheese or whey products the proven design of plate heat
exchangers offer superior hygienic reliability and simple cleaning-in-place (CIP)
routines.
CHEMICAL / PETROCHEMICAL
Plate heat exchangers have been successfully employed for decades in the chemical
industry in the most diverse sectors, such as the cooling and heating of base,
intermediate and final products, heat recovery or also the tempering of containers,
reactors and autoclaves.
Typical Applications are:-
o Cooling and heating of acids and caustic solutions
o Cooling of highly-viscous products (e.g. latex)
o Tempering and condensation of solvents (e.g. toluene)
o Cooling of water circuits
o Condensation of exhaust vapors, steam and multiple-material mixtures
o Secondary circuits with high levels of temperature similarity (∆t <2°C)
o Safety circuits to avoid contamination
PULP & PAPER
Certain industries benefit more than others from specific industrial products or machines.
Heat exchangers are pretty popular across the board, but are absolute essentials for the
paper industry. Without heat exchangers, paper mills would have exceedingly high
energy costs, which is bad for the environment as well as the purse size of the paper
companies. There are a couple ways that the paper and pulp industry utilize heat
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 11
exchangers, both of which are financial boosts, eco-friendly, efficient and effective
methods.
In essence, the paper process, beginning with wood pulp processing and refining and
then going into the bleaching and cleaning before the paper formation, is all done with
heat exchanger help. Specifically, plate heat exchangers are used to heat the liquids
used to create pulp from wood, a process involving chemical compounds that pull apart
the wood structure, leaving a goopy like substance that can be formed into paper after
more processing. Secondary processes involve bleaching or dying the pulp, which is a
process also heated by plate or spiral heat exchangers. After the desired color is
achieved, the pulp becomes paper by way of a paper machine, which knits the pulp
into thin webs that form sheets. During which all the moisture is removed and some type
of blower is utilized to dry it out completely.
MARINE
When conditions are tough, crew and equipment are really put to the test. The main
engine oil cooler and central fresh water cooler simply have to work. There is no room for
compromise when the sea is rough and the harbour far away.
For many decades plate heat exchangers have proved to be the perfect solution for
various closed-circuit cooling systems at sea. They are also frequently found in other
applications on board, such as tap-water production systems and HVAC systems.
A plate heat exchanger offers many advantages compared with conventional shell-and-
tube exchangers
o Up to 50% more efficient
o Up to 90% more compact
o 3-5 times higher k-values
o Unique turbulent flow design
o Closer temperature approach – as low as 1K
o Far less material – less use of exotic alloys or titanium
Likewise heat exchangers are used in almost every industry for heat transfer and heat recovery
applications. Even for our residential uses we all uses numerous types of heat exchangers like
Air Conditioning, Refrigerator, Oven, Water Heater and many more to mention.
HEAT EXCHANGER Dec’ 2014
ENERGY ALTERNATIVES INDIA (EAI), CHENNAI
www.eai.in Page 12
CHALLENGES IN HEAT EXCHANGERS :-
Some of the major Challenges in Heat Exchangers are :-
o To minimize size and weight.
o To minimize pressure drop.
o To meet required life.
o To be resistant to fouling and contamination.
o To minimize cost.
Fouling
Fouling occurs when impurities deposit on the heat exchange surface. Deposition of
these impurities can decrease heat transfer effectiveness significantly over time and are
caused by:
o Low wall shear stress
o Low fluid velocities
o High fluid velocities
o Reaction product solid precipitation
o Precipitation of dissolved impurities due to elevated wall temperatures
Heat exchanger performance can deteriorate with time, off design operations and
other interferences such as fouling, scaling etc. It is necessary to assess periodically the
heat exchanger performance in order to maintain them at a high efficiency level.
A heat Exchanger in steam power station contaminated with fouling