Harman Kardon AVR35

Harman KardonAVR35

Audio/VideoReceiver

Owners Manual

DIGITALCOAX AC-3

PRESET SCAN FM MODE DIGITAL PRO LOGIC 3-STEREO HALL 1 HALL 2 THEATER TEST TONE SURR. OFFPRESETTUNING

Mute

RLMaxMinMaxMin

Bass Treble Balance

Volume

Speaker Channel Dig. Select Delay

Set

VIDEO 3

Video Audio RL

AVR35 om (H) 2/5/99 10:41 AM Page 46

Owners ManualAVR35 Audio/Video Receiver

Table of ContentsIntroduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Front Panel Information Display . . . . . . . . . . . . . . . . . . . . . . 78Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . 1113Installation and Connections . . . . . . . . . . . . . . . . . . . . . . . 1415System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1621Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2227

Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Surround Mode Selection . . . . . . . . . . . . . . . . . . . . 2224Surround Mode Chart . . . . . . . . . . . . . . . . . . . . . . . . . . 23Digital Audio Playback . . . . . . . . . . . . . . . . . . . . . . 2426Tuner Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Tape Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2627Output Level Trim Adjustment . . . . . . . . . . . . . . . . . . . 27Memory Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Processor Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Programming the Remote . . . . . . . . . . . . . . . . . . . . . . . . . 2839Direct Code Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Auto Search Method . . . . . . . . . . . . . . . . . . . . . . . . 2829Code Readout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Programmed Device Functions . . . . . . . . . . . . . . . 2930Macro Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . 30Volume Punch-Through . . . . . . . . . . . . . . . . . . . . . . . . 31Re-Assigning Device Control Selectors . . . . . . . . . . . . . 31Function List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3233Setup Code Tables: TV . . . . . . . . . . . . . . . . . . . . . . . 3436Setup Code Tables: VCR . . . . . . . . . . . . . . . . . . . . . 3738Setup Code Tables: CD . . . . . . . . . . . . . . . . . . . . . . . . . 39Setup Code Tables: TAPE (LD) . . . . . . . . . . . . . . . . . . . 39Setup Code Tables: TAPE (DVD) . . . . . . . . . . . . . . . . . . 40Setup Code Tables: CABLE . . . . . . . . . . . . . . . . . . . . . . 40Setup Code Tables: SAT . . . . . . . . . . . . . . . . . . . . . . . . . 40

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

1998 Harman Kardon, Incorporated

250 Crossways Park DriveWoodbury, NY 11797

AVR35 om (H) 2/5/99 10:41 AM Page 47

Congratulations! With the purchaseof the Harman Kardon AVR35 you areabout to begin many years of listeningenjoyment. The AVR35 has been customdesigned to provide all the excitementand detail of movie sound tracks andevery subtle nuance of musical selec-tions. With on-board Dolby* DigitalDecoding, the AVR35 delivers six discretechannels of audio that take advantage ofthe digital sound tracks from the latestDVD and LV releases, as well as futureHDTV broadcasts.

While complex digital systems are hard at work within the AVR35 to make all ofthis happen, hookup and operation aresimple. Color-keyed connections and acomprehensive programmable remotecontrol make the AVR35 easy to use.

To obtain maximum enjoyment fromyour new receiver, we urge you to take afew minutes to read through this manual.This will ensure that connections tospeakers, source playback units and otherexternal devices are made properly. Inaddition, a few minutes spent learningthe functions of the various controls willenable you to take advantage of all thepower the AVR35 is able to deliver.

Introduction1

If you have any questions about thisproduct, its installation or operation,please contact your dealer. They are yourbest local source of information.

Description and FeaturesThe AVR35 is a full-featured A/V receiver,incorporating a wide variety of listeningoptions. In addition to Dolby Digitaldecoding, Dolby Pro Logic* and Dolby 3Stereo are available for compatibilitywith the tens of thousands of movies andtelevision programs encoded with analogsurround information. A choice of Halland Theater modes is also available foruse with both encoded sources and tradi-tional two-channel stereo recordings.

A total of four audio/video inputs, as wellas two additional audio-only inputs, andan FM stereo/FM/AM tuner are availablefor the utmost flexibility. Front-panel A/Vinputs simplify connections to videogames or camcorders.

The AVR35s powerful amplifiers usetraditional Harman Kardon High-CurrentDesign philosophies to meet the widedynamic range of any program selection.

Harman Kardon invented the high-fidelity receiver more than forty-five yearsago. With state-of-the-art features andtime-honored circuit designs, the AVR35 isone of the finest receivers ever offered byHarman Kardon.

n On-Board Dolby Digital Decoding

n Coax and Optical Digital Inputs

n Five Analog Surround Modes

n Pre-Programmed Learning Remote Control

n Composite Video Switching

AVR35 om (H) 2/5/99 10:41 AM Page 1

Safety Information

Important Safety Information

Verify Line Voltage Before UseYour AVR35 has been designed for usewith 120-volt AC current. Connection to aline voltage other than that for which itis intended can create a safety and firehazard, and may damage the unit.

If you have any questions about the volt-age requirements for your specific model,or about the line voltage in your area,contact your selling dealer before plug-ging the unit into a wall outlet.

Do Not Use Extension CordsTo avoid safety hazards, use only thepower cord attached to your unit. We donot recommend that extension cords beused with this product. As with all electri-cal devices, do not run power cords underrugs or carpets or place heavy objects onthem. Damaged power cords should bereplaced immediately with cords meetingfactory specifications.

Handle the AC Power Cord GentlyWhen disconnecting the power cord froman AC outlet, always pull the plug, neverpull the cord. If you do not intend to usethe unit for any considerable length oftime, disconnect the plug from the ACoutlet.

Do Not Open the CabinetThere are no user-serviceable compo-nents inside this product. Opening thecabinet may present a shock hazard, andany modification to the product will voidyour guarantee. If water or any metalobject such as a paper clip, wire or staple accidentally falls inside the unit,disconnect it from the AC power sourceimmediately, and consult an authorizedservice station.

CATV or Antenna GroundingIf an outside antenna or cable system isconnected to this product, be certain thatit is grounded so as to provide some pro-tection against voltage surges and staticcharges. Section 810 of the NationalElectrical Code, ANSI/NFPA No. 70-1984,provides information with respect toproper grounding of the mast and sup-porting structure, grounding of the lead-in wire to an antenna discharge unit,size of grounding conductors, location ofantenna discharge unit, connection togrounding electrodes and requirementsof the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER:This reminder is provided to call theCATV (Cable TV) system installers atten-tion to article 820-40 of the NEC thatprovides guidelines for proper groundingand, in particular, specifies that the cableground shall be connected to the ground-ing system of the building, as close to thepoint of cable entry as possible.

Installation Locationn To assure proper operation, and to

avoid the potential for safety hazards,place the unit on a firm and level sur-face. When placing the unit on a shelf,be certain that the shelf and anymounting hardware can support theweight of the product.

n Make certain that proper space is pro-vided both above and below the unitfor ventilation. If this product will beinstalled in a cabinet or other enclosedarea, make certain that there is suffi-cient air movement within the cabinet.Under some circumstances a fan maybe required.

n Do not place the unit directly on acarpeted surface.

n Avoid installation in extremely hot orcold locations, or an area that isexposed to direct sunlight or heatingequipment.

n Avoid moist or humid locations.

n Do not obstruct the ventilation slots onthe top of the unit, or place objectsdirectly over them.

2

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE

LA PRISE ET POUSSER JUSQU'AU FOND.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the

presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN

AVR35 om (H) 2/5/99 10:41 AM Page 2

Safety Information

CleaningWhen the unit gets dirty, wipe it with aclean, soft, dry cloth. If necessary, wipe itwith a soft cloth dampened with mildsoapy water, then a fresh cloth with cleanwater. Wipe dry immediately with a drycloth. NEVER use benzene, aerosolcleaners, thinner, alcohol or any othervolatile cleaning agent. Do not useabrasive cleaners, as they may damagethe finish of metal parts. Avoid sprayinginsecticide near the unit.

Moving the UnitBefore moving the unit, be certain to dis-connect any interconnection cords withother components, and make certainthat you disconnect the unit from the ACoutlet.

Important Information For the UserNOTE: This equipment has been testedand found to comply with the limits for a Class-B digital device, pursuant to Part15 of the FCC Rules. The limits aredesigned to provide reasonable protectionagainst harmful interference in aresidential installation. This equipmentgenerates, uses and can radiate radio-frequency energy and, if not installed andused in accordance with the instructions,may cause harmful interference to radiocommunication. However, there is noguarantee that harmful interference willnot occur in a particular installation. If this equipment does cause harmfulinterference to radio or television recep-tion, which can be determined by turningthe equipment off and on, the user is encouraged to try to correct the inter-ference by one or more of the followingmeasures:

n Reorient or relocate the receivingantenna.

n Increase the separation between theequipment and receiver.

n Connect the equipment into an outleton a circuit different from that towhich the receiver is connected.

n Consult the dealer or an experiencedradio/TV technician for help.

This device complies with Part 15 of theFCC Rules. Operation is subject to thefollowing two conditions: (1) this devicemay not cause harmful interference, and(2) this device must accept interferencereceived, including interference that maycause undesired operation.

NOTE: Changes or modifications maycause this unit to fail to comply with Part 15 of the FCC Rules and may voidthe users authority to operate the equipment.

Unpacking

The carton and shipping materials usedto protect your new receiver during ship-ment were specially designed to cushionit from shock and vibration. We suggestthat you save the carton and packingmaterials for use in shipping if you move,or should the unit ever need repair.

To minimize the size of the carton instorage, you may wish to flatten it. Thisis done by carefully slitting the tapeseams on the bottom and collapsing thecarton down to a more two-dimensionalappearance. Other cardboard inserts maybe stored in the same manner. Packingmaterials that cannot be collapsedshould be saved along with the carton ina plastic bag.

If you do not wish to save the packagingmaterials, please note that the cartonand other sections of the shipping protec-tion are recyclable. Please respect theenvironment and discard those materialsat a local recycling center.

Typographic Conventions

In order to help you use this manualwith the remote control, front panelcontrols and rear panel connections,certain conventions have been used.

EXAMPLE (bold type) indicates aspecific remote control or front panelbutton, or rear panel connection jack

EXAMPLE (OCR type) indicates amessage that is visible on the front panelinformation display

EXAMPLE (bold type) indicates a litindicator in the front panel informationdisplay

1 (number in a square) indicates aspecific front panel control

a (number in an oval) indicates abutton or indicator on the remote

` (number in a circle) indicates arear panel connection

A (letter in a square) indicates anindicator in the front panel display

3

AVR35 om (H) 2/5/99 10:41 AM Page 3

Front Panel Controls4

1 Main Power Switch2 System Power Control3 Power Indicator4 Headphone Jack5 Bass Control6 Treble Control7 Balance Control8 Video 3 Inputs9 Tape Selector) CD! DVD Input Selector@ Video Input Selectors

# AM/FM$ Sleep Button% Tuning Button^ Preset Scan& Preset Stations Selector* Tuner Mode( Dolby Digital Selector Dolby Pro Logic Selector Dolby 3 Stereo Selector Analog Surround Mode Selectors Test Tone Surround Off

Mute Volume Control Delay Digital Input Selector Set Button Channel Select Speaker Select Button Selector Buttons33 Information Display34 Remote Sensor Window

AVR 35

CDTAPE DVD VID 1 VID 2 VID 3 SLEEP AM/FM PRESET SCAN FM MODE DIGITAL PRO LOGIC 3-STEREO HALL 1 HALL 2 THEATER TEST TONE SURR. OFFPRESETTUNING

PhonesPower

Mute

RLMaxMinMaxMin

Bass Treble Balance

Volume

Speaker Channel Dig. Select Delay

Set

VIDEO 3

Video Audio RL

TUNEDSLEEP MONO STEREO AUTO MEMORY PRESET

MUTE

BYPASS

ANALOGDIGITAL

OPT COAXPRO LOGIC

AC-3 PCM MULTI NIGHT DISPLAYTHEATERHALL 2HALL 13-STEREO

9)! @ #$ % ^ &

3 4 5 6 7 8

1

2

(*

AVR35 om (H) 2/5/99 10:41 AM Page 4

Front Panel Controls5

1 Main Power Switch: Press thisbutton to apply power to the AVR35.When the switch is pressed in theunit is placed in a Standby mode, as indicated by the amber LED 3surrounding the System Powercontrol 2. This button MUST bepressed in to operate the unit. Toturn the unit off and prevent the useof the remote control, this switchshould be pressed until it pops outfrom the front panel so that the wordOFF may be read at the top of theswitch.

NOTE: In normal operation thisswitch is left in the ON position.

2 System Power Control: Whenthe Main Power Switch 1 is ON,press this button to turn on theAVR35; press it again to turn the unitoff. Note that the Power Indicatorsurrounding the switch 3 will turngreen when the unit is on.

3 Power Indicator: This LED willilluminate in amber when the unit isin the Standby mode to signal thatthe unit is ready to be turned on.When the unit is in operation, theindicator will turn green.

4 Headphone Jack: This jack maybe used to listen to the AVR35s out-put through a pair of headphones.Be certain that the headphoneshave a standard 14" stereo phoneplug.

5 Bass Control: Turn this control tomodify the low-frequency output ofthe left/right channels by as much as10dB. Set this control to a suitableposition for your taste and roomacoustics.

6Treble Control: Turn this controlto modify the high-frequency outputof the left/right channels by as muchas 10dB. Set this control to asuitable position for your taste androom acoustics.

7 Balance Control: Turn thiscontrol to change the relative volumefor the front left/right channels.

NOTE: For proper operation of thesurround modes this control shouldbe at the midpoint, or 12 oclockposition.

8 Video 3 Inputs: Theseaudio/video inputs may be used for temporary connection of videogames, camcorders, digital stillcameras or portable audio products.To select a source connected tothese jacks, press the Vid 3 InputSelector @.

9Tape Selector: Press this buttonto select the device connected tothe Tape Monitor jacks a as thelistening source. The previouslyselected source will continue toshow in the Information Display 33, and the red LED above thebutton will illuminate to remind youthat you are listening to the tapemonitor output.

) CD: Press this button to selectthe device connected to the CDInput jacks as the listeningsource.

! DVD Input: Press this button toselect the device connected to theDVD Play jacks as the listeningand viewing source.

@ Video Input Selectors: Pressone of these buttons to select asource connected to the rear panelAudio/Video inputs , or thefront panel Video 3 inputs 8.

# AM/FM: Press this button toselect the tuner as the AVR35s inputsource. When it is first pressed thelast station tuned will be heard.Press it again to change betweenAM and FM bands.

$ Sleep Button: Press this buttonto place the unit in the Sleep mode.After the time shown in the display,the AVR35 will automatically go intothe Standby mode. Each press ofthe button changes the time untilturn-off in the following order:

%Tuning Button: Press the left side of the button to tune lowerfrequency stations and the right sideof the button to tune higher frequencystations. When a station with a strongsignal is tuned, the TUNED indicatorR will illuminate in the InformationDisplay 33. A brief (1/2 second)press of the button will manuallytune to the next frequency incre-ment, while pressing and holding the button for a longer period willautomatically tune to the next stationwith a signal strong enough foracceptable reception.

^ Preset Scan: Press this button to automatically scan through thestations that have been programmedin the AVR35s memory. The tunerwill play five seconds of each stationbefore moving to the next presetstation. To stop the scan when thedesired station is heard, press thebutton again. (See page 26 for moreinformation on the tuner memorysystem.)

90min

80min

70min

60min

50min

40min

30min

20min

10min

5min

1min OFF

AVR35 om (H) 2/5/99 10:41 AM Page 5

Front Panel Controls

& Preset Stations Selector: Pressthis button to select stations thathave been entered into the presetmemory. (See page 26 for moreinformation on tuner programming.)

*Tuner Mode: Press this button toselect the stereo or mono mode forFM tuning. In the STEREO mode aStereo indicator P will illuminate inthe information display, and stereoreception will be provided when sta-tions are transmitting stereo signals.In the MONO mode the left and rightsignals from stereo broadcasts willbe mixed together and reproducedthrough all channels. Select MONOfor better reception of weak signals.

( Dolby Digital Selector: Pressthis button to select the Dolby Digitalsurround mode when listening to aprogram that carries the DolbyDigital information. (See pages 22-25for more information on surroundmodes and digital audio.)

Dolby Pro Logic Selector: Pressthis button to select the Dolby ProLogic surround mode when listeningto an analog program that is encodedwith surround-sound information. (Seepages 2225 for more information onsurround modes.)

Dolby 3 Stereo Selector: Pressthis button to select the Dolby 3Stereo listening mode. This mode isused primarily when a program hassurround information when a centerchannel speaker, but no surroundspeakers, is installed. (See pages2225 for more information onsurround modes.)

Analog Surround ModeSelectors: Press one of thesebuttons to select the analog sur-round modes. These modes may be used with any analog programsource to create a pleasing surroundeffect. (See pages 2225 for moreinformation on surround modes.)

Test Tone: Press this button tobegin the sequence of steps used toset the AVR35s output levels. Whenthis button is pressed, a test tone willreplace the currently selected listen-ing source. (See page 19 for moreinformation on using the test tone toset the output levels.)

Surround Off: Press this buttonto turn off all surround processing,and to listen to a program in tradi-tional stereo from the left front andright front speakers only.

Mute: Press this button tomomentarily silence the speakeroutput of the AVR35.

Volume Control: Turn the knobclockwise to increase volume, counterclockwise to decrease thevolume.

Delay: Press this button to beginthe sequence of steps required toenter delay time settings. (See page20 for more information on delaytimes.)

Digital Input Selector: Whenplaying a source that has a digitaloutput, press this button to selectbetween the Optical and Coaxial Digital inputs. (See pages 2225for more information on digital audio.)

Set Button: When makingchoices during the setup and con-figuration process, press this buttonto enter the desired setting, asshown in the Information Display33, into the AVR35s memory. (Seepages 1724 for more information onsetup and configuration.)

Channel Select: Press thisbutton to begin the process ofselecting and configuring theAVR35s output channels. (See pages 1724 for more information onsetup and configuration.)

Speaker Select Button: Pressthis button to begin the process ofselecting the speaker positions thatare used in your listening room. (Seepages 1724 for more information onsetup and configuration.)

Selector Buttons: When you areestablishing the AVR35s configura-tion settings, use these buttons toselect between the choices avail-able, as shown in the InformationDisplay 33.

33 Information Display: Thisdisplay delivers messages andstatus indications to help youoperate the receiver. (See page 7 for a complete explanation of theInformation Display.)

34 Remote Sensor Window: Thesensor behind this window receivesinfrared signals from the remote con-trol. Aim the remote at this area anddo not block or cover it unless anexternal remote sensor is installed.

6

AVR35 om (H) 2/5/99 10:41 AM Page 6

Front Panel Information Display7

TUNEDSLEEP MONO STEREO AUTO MEMORY PRESET

MUTE

BYPASS

ANALOGDIGITAL

OPT COAXPRO LOGIC

AC-3 PCM NIGHTTHEATERHALL 2HALL 13-STEREO

AB

C E GL

KJ

T R Q P O N MS

D F HI

A MuteB BypassC AnalogD Dolby Digital IndicatorE Optical SourceF Analog Dolby Surround Mode IndicatorsG Coax Source

H AC-3 IndicatorI PCM IndicatorJ Analog Surround Mode IndicatorsK Night IndicatorL Preset NumberM Preset IndicatorN Memory

O AutoP Stereo IndicatorQ Mono IndicatorR Tuned IndicatorS Main Information DisplayT Sleep Indicator

AVR35 om (H) 2/5/99 10:41 AM Page 7

Front Panel Information Display

A Mute: This indicator illuminates to remind you that the AVR35s out-put has been silenced by pressingthe Mute button . Press theMute button again to return to thepreviously selected output level.

B Bypass: This indicator illumi-nates when the surround processinghas been disabled by pressing theSurround Off button . When thisindicator is lit, the AVR35 will playtraditional stereo sound using thefront left and front right speakersonly.

C Analog: This indicator illuminateswhen an analog input source is in use.

D Dolby Digital Indicator: Thisindicator illuminates when a DolbyDigital source is being played.

E Optical Source: This indicatorilluminates when a digital source is in use via a connection to theOptical Digital input .

F Analog Dolby Surround ModeIndicators: These indicators illumi-nate when one of the analog (matrix)Dolby Surround modes is in use.

G Coax Source: This indicator illu-minates when a digital source is inuse via a connection to the CoaxialDigital input .

H AC-3* Indicator: This indicatorilluminates when the AVR35 isdecoding a Dolby Digital inputsource.

I PCM Indicator: This indicatorilluminates to show that a standardPCM (SP/DIF) digital audio signal is being decoded by the digital-to-analog converter.

J Analog Surround ModeIndicators: These indicators illumi-nate when one of the DSP generatedanalog surround modes is in usewith an analog input source.

K Night Indicator: This indicatorlights when the AVR35 is in the Nightmode, which prevents the AVR35from loud playback when digitalsources are in use.

L Preset Number: This two-digitdisplay indicates the station presetnumber that is currently in use, orthat is being entered.

M Preset Indicator: This indicatorilluminates when one of the stationsentered into the preset memory istuned. The number that appearsbelow the indicator is the presetstations memory.

N Memory: This indicator flasheswhen entering presets and otherinformation into the tuners memory.

O Auto: This indicator illuminateswhen the Auto mode is in use forFM tuning.

P Stereo Indicator: This indicatorilluminates when an FM station isbeing tuned in stereo.

Q Mono Indicator: This indicatorilluminates when the tuner has beenplaced in the monaural mode bypressing the Tuner Mode button *.Set the tuner for mono listening to cut noise and improve the quality ofdistant stereo signals.

RTuned Indicator: This indicatorilluminates when a station is beingreceived with sufficient signalstrength to allow for acceptablelistening quality.

S Main Information Display: Thisdisplay shows messages relating tothe status, input source, surroundmode, tuner, volume level or otheraspects of units operation.

T Sleep Indicator: This indicator isilluminated when the Sleep functionis in use. The number that appearsabove the indicator is the number ofminutes remaining before the AVR35will return to the Standby mode.

8

AVR35 om (H) 2/5/99 10:41 AM Page 8

Rear Panel Connections9

UNSWITCHEDTOTAL 100W MAX.

SWITCHEDTOTAL 50W MAX.

(120V.60Hz)TOTAL 150W MAX

MODEL NO. AVR-35HARMAN KARDON

NORTHRIDGECALIFORNIA, USA

MADE IN CHINA

FM(75)

AM

ANTENNA

GND

AC 120V 60 HzIN

OUT

TAPEMONITOR

RIGHT

SPEAKERS 8 Ohms SPEAKER 8 Ohm

LEFT CENTER

VIDEO2

PLAYIN

RECOUT

VIDEO1

DVD

CD

FRONT CENTER

SERIAL NO.

AC OUTLETS

RIGHT

SPEAKERS 8 Ohms

LEFT

SURROUND

AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN

OUT IN

TVMONITOR

OUT

VIDEO 2

IN

OUT

DVD

VIDEO 1

OPTICAL

COAXIAL

SUB WOOFER

DIGITAL INPUT

PRE OUT

VIDEO

REMOTE CONTROL

ab

`

` AM Antenna FM Antenna Video 1 Inputs Video 1 Outputs CD Inputs DVD Inputs Subwoofer Pre-Out

Front Center Surrounds Unswitched AC Outlet Switched AC Outlet Power Cable Video 2 Inputs

TV Monitor Video Output AC-3/PCM Coaxial Input AC-3/PCM Optical Input Remote IR In Remote IR Outa Tape Monitor Inb Tape Monitor Out

` AM Antenna: Connect the AMloop antenna supplied with thereceiver to these terminals. If anexternal AM antenna is used, makeconnections to the AM and GNDterminals in accordance with theinstructions supplied with theantenna.

FM Antenna: Connect an indooror external FM antenna to this terminal.

Video 1 Inputs: Connect thesejacks to the audio and videoPLAY/OUT jacks of a VCR.

Video Outputs 1: Connect thesejacks to the audio and videoRECORD/IN jacks of a VCR.

CD Inputs: Connect these jacksto the output of a compact discplayer or CD changer.

DVD Inputs: Connect the analogaudio outputs and composite videooutput of a DVD or LV player to thesejacks.

Subwoofer Pre-Out: Connectthis jack to the line level input of apowered subwoofer. If an externalsubwoofer amplifier is used, connectthis jack to the subwoofer amplifierinput.

AVR35 om (H) 2/5/99 10:41 AM Page 9

Rear Panel Connections10

Front: Connect these terminals tothe front left/right speakers.

Center: Connect these terminalsto the center speaker.

Surrounds: Connect theseterminals to the surround speakers.

Unswitched AC Outlet: Thisoutlet may be used to power any ACdevice. The power will remain on atthis outlet regardless of whether theAVR35 is on or off.

NOTE: The power consumption ofthe device plugged into each ofthese outlets should not exceed100 watts.

Switched AC Outlet: This outletmay be used to power any devicethat you wish to have turn on whenthe unit is turned on with the SystemPower Control switch 2.

Power Cable: Connect the ACplug to a non-switched AC wall output.

Video 2 Inputs: Connect thesejacks to the audio and video outputsof a TV Tuner, Cable TV converterbox, satellite receiver or any otheraudio/video source.

TV Monitor Video Output:Connect this jack to the standard(composite) video input of a TVmonitor or video projector to viewthe on-screen menus and the output of any standard video sourceselected by the receivers videoswitcher.

AC-3/PCM Coaxial Input:Connect the coax digital output froma DVD player, HDTV receiver, LVplayer or CD player to this jack. Thesignal may be either a Dolby Digital(AC-3) signal or a standard PCMdigital source.

AC-3/PCM Optical Input:Connect the optical digital outputfrom a DVD player, HDTV receiver,LV player or CD player to this jack.The signal may be either a DolbyDigital (AC-3) signal or a standardPCM digital source.

Remote IR In: If the AVR35s frontpanel IR sensor is blocked due tocabinet doors or other obstructions,an external IR sensor may be used.Connect the output of the sensor tothis jack.

Remote IR Out: This connectionpermits the IR sensor in the receiverto serve other remote controlleddevices. Connect this jack to the IRIN jack on Harman Kardon or othercompatible equipment.

aTape Monitor In: Connect thesejacks to the PLAY/OUT jacks of anaudio recorder.

bTape Monitor Out: Connect thesejacks to the RECORD/INPUT jacks ofan audio recorder.

AVR35 om (H) 2/5/99 10:41 AM Page 10

Remote Control Functions11

AVR TV

SAT

CBL VCRTAPECD

POWER

TEST

T/V

VOLMUTE

SLEEP

CH

SURRDISC

SPKR

MENUDISP LEVEL

LEVEL

DISC

SETDIGICH

NIGHT DELAY

PREV. CHEXIT

CD

VID2

AM / FM

TAPE VID1

DWN-TUNING-UP

DWN-PRESET-UPVID3

+10

DVD

1 2 3 4 5

6 7 8 9 0

INFO ENTER

DIRECTTUN-MMEMCLR

M1 M2 M3 M4

AVR 35

b

a

rs

t

u

v

w

x

y

z

c

de

f

g

h

i

j

k

l

m

n

o

pq

a Program/Command Indicatorb AVR Selectorc Device Control Selectorsd Power Buttone Sleep Buttonf Channel / Buttonsg Surround Mode Selectorh / Buttonsi /Channel Buttonj Set Buttonk Night Model Source Selectorsm +10 Buttonn Numeric Keyso Info Buttonp Clear Buttonq Memory Buttonr Tuner Modes Directt Enteru Preset Up/Downv Tuning Up/Downw Transport Controlsx Delay/Prev Ch.y /Digital Buttonz Speaker Configuration Mute

VolumeTestTV/VCR

AVR35 om (H) 2/5/99 10:41 AM Page 11

Remote Control Functions

IMPORTANT NOTE: The AVR35sremote may be programmed to con-trol up to five additional devices,including the AVR35. Before usingthe remote, it is important to remem-ber to press the Device ControlSelector button b c that corre-sponds to the unit you wish to oper-ate. In addition, the AVR35s remoteis shipped from the factory to oper-ate the AVR35 and Harman KardonCD players and cassette decks. Theremote is also capable of operatinga wide variety of other productsusing the control codes that are partof the remote. Before using theremote with other products, followthe instructions on pages 2829 toprogram the proper codes for theproducts in your system.

It is also important to remember thatmany of the buttons on the remotetake on different functions, depend-ing on the product selected usingthe Device Control Selectors. Thedescriptions shown here primarilydetail the functions of the remotewhen it is used to operate theAVR35. (See pages 2831 for infor-mation about alternate functions forthe remotes buttons.)

a Program/Command Indicator:This LED is used as an indicator toassist in programming the remotecontrol. (See pages 2831 for moreinformation on programming theAVR35.)

b AVR Selector: Press this buttonto use the remote control for operationof the AVR35. Note that the button willbriefly turn red after it has beenpressed to confirm your selection.

c Device Control Selectors:Press one of these buttons to use theremote to control the functions ofanother audio/video device. Note thatthe button will briefly turn red after ithas been pressed to confirm your

selection. (See pages 2831 for infor-mation on programming the AVR35sremote to operate these devices.)

d Power Button: Press this buttonto turn the currently selected deviceon or off.

e Sleep Button: Press this buttonto place the unit in the Sleep mode.After the time shown in the display,the AVR35 will automatically go intothe Standby mode. Each press ofthe button changes the time untilturn-off in the following order:

f Channel / Buttons:When the remote is being used tocontrol a TV, VCR or Cable box, pressthese buttons to change the channelbeing viewed.

g Surround Mode Selector: Pressthis button to begin the process ofchanging the surround mode. Afterthe button has been pressed, usethe / buttons h to select thedesired surround mode. (See page24 for more information.)

h / Buttons: These are multi-purpose buttons. They will be usedmost frequently to select a surroundmode. To change the surround mode,first press the SURR button g. Nextpress these buttons to scroll up ordown through the list of surroundmodes that appear in the InformationDisplay 33. (See page 24 for moreinformation.) These buttons are alsoused to increase or decrease outputlevels used to lower the AVR35s out-put levels when configuring the unitwith either the internal test tone or an external source. (See pages 19and 26 for more information.) Theyare also used to enter delay timesettings after the Delay button xhas been pressed. (See page 20 formore information.)

90min

80min

70min

60min

50min

40min

30min

20min

10min

5min

1min OFF

i /Channel Button: This button is used to start the process of setting the AVR35s output levelsto an external source. Once this but-ton is pressed, use the / buttonsh to select the channel beingadjusted, then press the Set buttonj, followed by the / buttonsagain to change the level letting.(See page 27 for more information.)

j Set Button: This button is usedto enter settings into the AVR35smemory. It is also used in the setupprocedures for delay time, speakerconfiguration and channel outputlevel adjustment. (See pages 1721for complete information.)

k Night Mode: Press this button to activate the Night mode, pre-venting loud playback when the digital modes are in use without altering the dynamic range of theoutput signal.

l Source Selectors: Press thesebuttons to select an input source forthe AVR35. The AM/FM button is alsoused to switch between frequencybands when the tuner is in use.

NOTE: Pressing one of these buttonsselects the source only. In order tocontrol the actual source machineusing the remote you must press theDevice Control Selector button cfor the desired product.

m +10 Button: This button doesnot have a function for the AVR35,but when the remote is used to con-trol certain CD players, TV sets andVCRs it may be used to select tracksor channel numbers

n Numeric Keys: These buttonsserve as a ten-button numeric key-pad to enter tuner preset positions.They are also to be used to selectchannel numbers when TV has beenselected on the remote, or to selecttrack numbers on a CD, DVD or LDplayer, depending on how theremote has been programmed.

12

AVR35 om (H) 2/5/99 10:41 AM Page 12

Remote Control Functions

o Info Button: This button doesnot function with the AVR35, but itmay be used when the remote isused to control other products.

p Clear Button: This button doesnot function with the AVR35, but it isavailable for use with other devices.

q Memory Button: Press this button to enter a radio station intothe AVR35s preset memory. Afterpressing the button the MEMORYindicator N will flash, and you thenhave five seconds to enter a presentmemory location using the NumericKeys n. (See page 26 for moreinformation.)

rTuner Mode: Press this buttonwhen the tuner is in use to selectbetween automatic tuning andmanual tuning. When the button ispressed so that the AUTO indicatorO goes out, pressing the Tuningbuttons v will move the frequencyup or down in single-step incre-ments. When the FM band is in use, pressing this button when astations signal is weak will changeto monaural reception, as indicatedby the MONO indicator Q. (See page26 for more information.)

s Direct : Press this button toselect a radio station by entering its frequency using the NumericKeys n. (See page 26 for moreinformation.)

t Enter: This button does not function with the AVR35, but it isavailable for use with other devices.

u Preset Up/Down: When thetuner is in use, these buttons scrollthrough the stations that have beenprogrammed into the AVR35s mem-ory. When many source devices,such as CD players, VCRs and cas-sette decks, are selected using theDevice Control Selectors c,these buttons will normally functionas chapter step or track advance.

vTuning Up/Down: When thetuner is in use, these buttons will tune up or down through the selectedfrequency band. If the Tuner Modebutton r has been pressed so thatthe AUTO indicator O is illuminated,pressing these buttons will cause thetuner to seek the next station withacceptable signal strength for qualityreception. When the AUTO indicatorO is NOT illuminated, pressing thesebuttons will tune stations in single-step increments. (See page 26 formore information.)

wTransport Controls: These con-trols do not control any functions ofthe AVR35, but they are used exten-sively when operating a wide varietyof CD players, cassette decks andVCRs. (See page 28 for informationon programming the remote to utilizethese buttons.)

x Delay/Prev Ch.: Press this but-ton to begin the process for settingthe delay times used by the AVR35when processing surround sound.After pressing this button the delaytimes are entered by pressing theSet button j, and then using the / buttons h to change the set-ting. Press the Set button again tocomplete the process. (See page 20for more information.)

y /Digital Button: This button isused to select the type of digital inputused with any one of the input sourcesconnected to the AVR35. After press-ing this button, use the / buttonsh to make your selection betweenOPTICAL E or COAXIAL G digital.Press the Set button j to enteryour choice. (See page 24 for moreinformation.)

z Speaker Configuration: Pressthis button to begin the process ofconfiguring the AVR35s BassManagement System for use withthe type of speakers used in yoursystem. Once the button has beenpressed, use the / buttons h toselect the channel you wish to set up.Press the Set button j, and thenselect another channel to configure.When all adjustments have beencompleted, press the Set buttontwice to exit the settings and returnto normal operation. (See page 17for more information.)

Mute: Press this button tomomentarily silence the AVR35 or TVset being controlled, depending onwhich device has been selected.

When the AVR35 remote is being pro-grammed to operate another device,this button is pressed with the DeviceControl Selector button c tobegin the programming process.(See page 28 for more informationon programming the remote.)

Volume: Press these buttons toraise or lower the system volume.

Test: Press this button to beginthe sequence used to calibrate theAVR35s output levels. (See page19for more information on calibratingthe AVR35.)

TV/VCR: This button does not function with the AVR35, but it isavailable for use with other devices.

13

AVR35 om (H) 2/5/99 10:41 AM Page 13

Installation and Connections

System InstallationAfter unpacking the unit, and placing iton a solid surface capable of supportingits weight, you will need to make theconnections to your audio and videoequipment. These steps need to be doneonly when the receiver is first installed,or when a change is made to the inputsource equipment.

Audio Equipment ConnectionsWe recommend that you use high-qualityinterconnect cables when making connec-tions to source equipment and recordersto preserve the quality of the signals.

When making connections to audiosource equipment or speakers it is alwaysa good practice to unplug the unit fromthe AC wall outlet. This prevents any pos-sibility of accidentally sending audio ortransient signals to the speakers that maydamage them.

1. Connect the analog output of a CDplayer to the CD inputs .

NOTE: When the CD player has bothfixed and variable audio outputs it is bestto use the fixed output unless you findthat the input to the receiver is so lowthat the sound is noisy, or high that thesignal is distorted.

2. Connect the Play/Out jacks of a cas-sette deck, MD or other audio recorder tothe Tape Monitor In jacks a. Connectthe Record/In jacks on the recorder tothe Tape Monitor Out jacks b on the AVR35.

3. Connect the output of any digitalsources to be used to the appropriateconnections on the AVR35 rear panel.Note that the Optical and Coaxialdigital inputs may be used witheither a Dolby Digital (AC-3) source or the output of a conventional CD or LV players PCM (SP/DIF) output.

4. Assemble the AM Loop Antenna sup-plied with the unit as shown below.Connect it to the AM and GND screwterminals `.

5. Connect an FM antenna to the FM (75 ohm) connection . The FM antenna may be an external roofantenna, an inside powered or wire leadantenna or a connection from a cable TV system. Note that if the antenna orconnection uses 300-ohm twin-leadcable, you must use the 300-ohm-to-75-ohm adapter supplied with the unit to make the connection.

6. Connect the front, center andsurround speaker outputs to the respective speakers.

To assure that all the audio signals arecarried to your speakers without loss ofclarity or resolution, we suggest that youuse high-quality speaker cable. Manybrands of cable are available, and thechoice of cable may be influenced by thedistance between your speakers and thisreceiver, the type of speakers you use,personal preferences and other factors.

Your dealer or installer is a valuableresource to consult in selecting theproper cable.

Regardless of the brand of cable selected,we recommend that you use a cable con-structed of fine, multistrand copper with agauge of 14 or smaller. Remember that inspecifying cable, the lower the number,the thicker the cable.

Cable with a gauge of 16 may be used forshort runs of less than ten feet. We do notrecommend that you use cables with anAWG equivalent of 18 or higher due tothe power loss and degradation inperformance that will occur.

Cables that are run inside walls shouldhave the appropriate markings to indicatelisting with UL, CSA or other appropriatetesting agency standards. Questions aboutrunning cables inside walls should bereferred to your installer or a licensedelectrical contractor who is familiar withthe NEC and/or the applicable localbuilding codes in your area.

When connecting wires to the speakers,be certain to observe proper polarity.Remember to connect the negative orblack wire to the same terminal on thereceiver and the speaker. Similarly, thepositive or red wire should be con-nected to the like terminal on the AVR35and speaker.

We also recommend that the length ofcable used to connect speaker pairs beidentical. For example, use the samelength piece of cable to connect the frontleft and front right or surround left andsurround right speakers, even if thespeakers are a different distance fromthe AVR35.

14

AVR35 om (H) 2/5/99 10:41 AM Page 14

Installation and Connections

NOTE: While most speaker manufacturersadhere to an industry convention of usingblack terminals for negative and red onesfor positive, some manufacturers mayvary from this configuration. To assureproper phase, and optimal performance,consult the identification plate on yourspeaker, or the speakers manual to verifypolarity. If you do not know the polarity of your speaker, ask your dealer for advice before proceeding, or consult the speakers manufacturer.

7. Connections to a subwoofer are madevia a line-level audio connection fromthe Subwoofer Output to the line-level input of a subwoofer with a built-inamplifier. If a passive subwoofer is used,the connection first goes to a poweramplifier, which will be connected to oneor more subwoofer speakers.

Video Equipment ConnectionsVideo equipment is connected in a fashionsimilar to audio components. Again, theuse of high-quality interconnect cables isrecommended to preserve signal quality.

1. Connect a VCRs audio and videoPlay/Out jacks to the Video 1 In jacks on the rear panel. The audio andRecord/Out jacks on the VCR should beconnected to the Tape Monitor Outjacks b on the AVR35.

2. Connect the audio and video outputsof a satellite receiver, cable TV converteror television set or any other video sourceto the Video 2 In jacks .

3. Connect the audio and video outputsof a DVD or laser disc player to the DVDjacks .

4. Connect the TV Monitor Out jacks on the receiver to the video input of your television monitor or video projector.

System and Power Connections

The AVR35 is designed for flexible usewith external control components andpower amplifiers. These connections areeasy to make during an initial installa-tion, or at a later date should you chooseto upgrade your system.

Remote Control ExtensionIf the receiver is placed behind a solid orsmoked glass cabinet door, the obstruc-tion may prevent the remote sensor fromreceiving commands. In this event, anoptional remote sensor may be used.Connect the output of the remote sensorto the Remote Cont. In jack .

If other components are also preventedfrom receiving remote commands, onlyone sensor is needed. They may use thisunits sensor or a remote eye by runninga connection from the Remote Cont.Out jack to the Remote In jack onHarman Kardon or other compatibleequipment.

AC Power ConnectionsThis unit is equipped with two accessoryAC outlets. They may be used to poweraccessory devices, but they should not beused with high-current draw equipmentsuch as power amplifiers. The total powerdraw may not exceed 50W to each outlet.

The Switched outlet will receivepower only when the unit is on. This isrecommended for devices that have nopower switch, or a mechanical powerswitch that may be left in the ON position.

NOTE: Devices with electronic powerswitches may only go into a Standbymode when plugged in here.

The Unswitched outlet will receivepower as long as the unit is plugged intoa powered AC outlet.

Finally, when all connections are com-plete, plug the power cord into a non-switched 120-volt AC wall outlet. Yourealmost ready to enjoy the AVR35!

15

AVR35 om (H) 2/5/99 10:41 AM Page 15

System Configuration

When all audio, video and system con-nections have been made, there are a fewconfiguration adjustments to be made. Afew minutes spent to correctly configureand calibrate the unit will greatly add toyour listening experience.

Speaker Selection and PlacementThe placement of speakers in a multi-channel-home-theater system can have a noticeable impact on the quality ofsound reproduced.

No matter which type or brand of speakersis used, the same model or brand ofspeaker should be used for the front left,center and right speakers. This creates aseamless front soundstage, and elimi-nates the possibility of distracting sonicdisturbances that occur when a soundmoves across mismatched front-channelspeakers.

Speaker PlacementDepending on the type of center-channelspeaker in use and your viewing device,place the center speaker directly above orbelow your TV or in the center behind aperforated front projection screen.

Once the center-channel speaker isinstalled, position the left and right front speakers so that they are as faraway from one another as the center-channel speaker is from the preferredlistening position. Ideally, the front-channel speakers should be placed sothat their tweeters are no more than 24"off center from the tweeter in the center-channel speaker.

Depending on the specifics of your roomacoustics and the type of speakers in use,you may find that imaging is improvedby moving the front left and right speak-ers slightly forward of the center-channel

speaker. If possible, adjust all front loudspeakers so that they are aimed atear height when you are seated in the listening position.

Using these guidelines, youll find that ittakes some experimentation to find thecorrect location for the front speakers inyour particular installation. Dont beafraid to move things around until thesystem sounds correct. Optimize yourspeakers so that pans across the front ofthe room sound smooth, and that soundsfrom all speakers appear to arrive at thelistening position at the same time with-out delay from the center speaker asopposed to the left and right speakers.

Surround speakers should be placed onthe side walls of the room, at or slightlybehind the listening position. The centerof the speaker should face into the room.The speakers should be located so thatthe bottom of the cabinet is at least twofeet higher than the listeners ears whenseated in the desired area.

If side wall mounting is not practical, thespeakers may be placed on a rear wall,behind the listening position. Again, theyshould be located so that the bottom ofthe cabinet is at least two feet higherthan the listeners ears. The speakersshould be no more than six feet behindthe rear of the seating area.

Subwoofers produce non-directionalsound, so they may be placed almostanywhere in a room. Subwoofer place-ment is highly influenced by room sizeand shape, and the type of subwooferused. Follow the instructions of the sub-woofers manufacturer, or experimentwith the best location for a subwoofer inyour listening room.

16

Right FrontSpeaker

Left FrontSpeaker

No morethan 24"

Center Front Speaker

A) Front-Channel Speaker Installation with Direct-View TV Sets or Rear-ScreenProjectors

Center FrontSpeaker

Optional Rear Wall Mounting

TV or Projection Screen

Right FrontSpeaker

Left FrontSpeaker

No

mor

e th

an 6

feet

whe

n re

ar-m

ount

edsp

eake

rs a

re u

sed

At least 2 feet

At least 6 inches from ceiling

B) The distance between the left and rightspeakers should be equal to the distancefrom the seating position to the viewingscreen.You may also experiment withplacing the left and right speakers slightlyforward of the center speaker.

AVR35 om (H) 2/5/99 10:41 AM Page 16

System Configuration17

System SetupOnce the speakers have been placed in theroom and connected, the final step in thesetup process is to enter the settings thatconfigure the AVR35s bass managementsystem for the type of speakers used inyour system, the calibration of the outputlevels and the delay times used by the sur-round sound processor. Before proceedingfurther, this is a good time to review theinstallation section of the manual tomake certain that all connections areproperly made.

You are now ready to power up the AVR35to begin these final adjustments.

1. Plug the Power Cable into anunswitched AC outlet.

2. Press the Main Power Switch 1in so that it latches in with the OFFwording on the top of the switchinside the front panel. Note that thePower Indicator 3 will turnamber, indicating that the unit is inthe Standby mode.

3. Install the three supplied AAA batteriesin the remote as shown. Be certain toobserve the (+) and () polarityindicators shown in the bottom of thebattery compartment.

4. Turn the AVR35 on either by pressingthe System Power Control 3onthe front panel, or via the remote byfirst pressing the AVR Selector a,and then pressing the Power buttond . The Power Indicator 3 willturn green to confirm that the unit ison, and the Information Display will also light up.

Speaker ConfigurationThe first few adjustments tell the AVR35which type of speakers are in use. This isimportant as it adjusts the settings thatdetermine which speakers receive low-frequency (bass) information. For eachof these settings use the LARGE setting ifthe speakers for a particular position aretraditional full-range loudspeakers thatare capable of reproducing sounds below100Hz. Use the SMALL setting for small-er, frequency-limited satellite speakersthat do not reproduce sounds below100Hz. Note that when small speakersare used, a subwoofer is required toreproduce low-frequency sounds.Remember that the large and smalldescriptions do not refer to the actualphysical size of the speakers, but theirability to reproduce low-frequencysounds. If you are in doubt as to whichcategory describes your speakers, consultthe specifications in the speakers ownersmanual, or ask your dealer.

With the AVR35 turned on, follow thesesteps to configure the speakers:

1. Put the AVR35 in the Dolby Pro Logicmode by pressing the Dolby ProLogic Selector on the frontpanel or by pressing the SurroundMode Selector gon the remote,followed by the / buttons huntil PRO LOGIC appears in theMain Information Display S andthe PRO LOGIC indicator F lights.

2. Press the Speaker button z onthe remote or front panel. The wordsFRNT SPEAKERwill appear in theMain Information Display S .

3. Press the Set button j.

4. Press the / buttons h on theremote or the Selector buttonson the front panel until eitherLARGE or SMALL appears to matchthe type of speakers you have at theleft front and right front positions, asdescribed by the definitions shownbelow.

When SMALL is selected, low-frequency sounds will be sent to thesubwoofer output only. Note that ifyou choose this option, and there isno subwoofer connected, you willnot hear any low-frequency soundsfrom the front channels.

AVR35 om (H) 2/5/99 10:41 AM Page 17


When LARGE is selected, a full-range output will be sent to thefront left and right outputs, and NO low-frequency signals will besent to the subwoofer output.

5. When you have completed yourselection for the front channel, pressthe Set button j, and thenpress the / buttons h on theremote or the Selector buttonson the front panel to change thedisplay to CEN SPEAKER.

6. Press the Set button j again,and use the / buttons h on the remote, or the Selector buttons on the front panel, to select theoption that best describes your systembased on the speaker definitionsshown above.

When CEN SP SMALL is select-ed, low-frequency center-channelsounds will be sent to the subwooferoutput only. Note that if you choosethis option and there is no sub-woofer connected, you will not hearany low-frequency sounds from thecenter-channel speaker.

When CEN SP LARGE is select-ed, a full-range output will be sentto the center speaker output, andNO center-channel signal will besent to the subwoofer output.

When CEN SP NONE is selected,no signals will be sent to the center-channel output. The receiver willoperate in a phantom center-channel mode and center-channelinformation will be sent to the left-and right-front-channel outputs.

7. When you have completed yourselection for the center channel, pressthe Set button j, and thenpress the / buttons h on theremote or the Selector buttonson the front panel to change thedisplay to SUR SPEAKER.

8. Press the Set button j again,and then use the / buttons hon the remote or the Selectorbuttons on the front panel toselect the option that best describesyour system based on the speakerdefinitions shown above.

When SUR SP SMALL is select-ed, low-frequency surround chan-nel sounds will be sent to thesubwoofer output only. Note that ifyou choose this option and there isno subwoofer connected, you willnot hear any low-frequency soundsfrom the surround speaker.

When SUR SPLARGE is selected, afull-range output will be sent to thesurround-channel outputs, and NOsurround-channel signals will be sentto the subwoofer output.

When SUR SP NONE is selected,surround-sound information will besplit between the front-left and front-right outputs. Note that for optimalperformance when no surroundspeakers are in use, the Dolby 3 Stereo mode should be used instead of Dolby Pro Logic.

9. When you have completed yourselection for the surround channel,press the Set button j, and then press the / buttons h on the remote or the Selector buttonson the front panel to change the displayto SW SPEAKER.

10. Press the Set button j, and then press the / buttons h on the remote or the Selector buttonson the front panel to select the optionthat best describes your system.

Select S-W SP ON if a subwoofer is connected to your system.

Select S-W SP OFF if a subwoofer isNOT connected to your system. Notethat when no subwoofer is selected,low-frequency sounds below 100Hzwill be sent to the front left/rightspeakers, provided that the selection in step 4, above, has been set toLARGE. Otherwise, no low-frequencysounds will be heard. This option isnot available when the front, center orsurround speakers are set to SMALL.

AVR35 om (H) 2/5/99 10:41 AM Page 18


11. When all speaker selections havebeen made, press the Set button j to return to normal operation.

Output Level AdjustmentOutput level adjustment is a key part ofthe configuration process for any sur-round sound product. It is particularlyimportant for a Dolby Digital receiversuch as the AVR35, as correct outputs willensure that you hear sound tracks in theirproper place with the proper intensity.

IMPORTANT NOTE: Many listeners areoften confused about the operation of thesurround channels. While some assumethat sound should always be coming fromeach speaker, most of the time there willbe little or no sound in the surroundchannels. This is because they are onlyused when a movie director or soundmixer specifically places sound there tocreate ambiance, an effect or to continueaction from the front of the room to therear. When the output levels are properlyset it is normal for rear/surround speakersto operate only occasionally. Artificiallyincreasing the volume to the rearspeakers may destroy the illusion of anenveloping sound field that duplicates theway you hear sound in a movie theater orconcert hall.

Before beginning the adjustment processmake certain that all speaker connectionshave been properly made. The systemvolume should be set to the level that you will use during a typical listeningsession. Finally, make certain that theBalance Control 7 is set to the center12 oclock position.

To adjust and calibrate the output levels,follow these steps. For accurate calibration,it is a good idea to make these adjustmentsfrom the location in your room that isyour favorite listening position:

1. Put the AVR35 in the Dolby Pro Logicmode by pressing the Dolby ProLogic Selector on the frontpanel or by pressing the SurroundMode Selector gon the remote,followed by the / buttons huntil PRO LOGIC appears in theMain Information Display S andthe PRO LOGIC indicator F lights.

2. Press the Test Tone button on the remote or front panel. Thewords T -T FL 0dBwill appearin the Main Information DisplayS , and the letters FLwill flash onceeach second.

3. At this point, the test noise will beginto circulate among all the speakers ina clockwise rotation.

NOTE: This is a good time to verifythat the speakers have been properlyconnected. As the test noise circulates,listen to make certain that the soundcomes from the speaker positionshown in the Main InformationDisplay. If the sound from a speakerlocation does NOT match the positionindicated in the display, turn theAVR35 off and check the speakerwiring to make certain that eachspeaker is connected to the correctoutput terminal.

4. After checking for speaker placement,let the test noise circulate again, andlisten to see which channels soundlouder than the others. Using thefront left (FL in the display) speakeras a reference, press the / buttonsh on the remote or the Selectorbuttons on the front panel oneach channel to begin to bring themto the same level. Note that when oneof the buttons is pushed, the test noisecirculation will pause on the channelbeing adjusted to give you time tomake the adjustment. When yourelease the button, the circulationwill resume.

5. Continue to adjust the individualspeakers until they all have the samevolume. Note that adjustmentsshould be made with the /buttons h on the remote or theSelector buttons on the frontpanel only, NOT the main volumecontrols. Then press the Set buttonj to memorize the change. Ifyou are using a sound pressure (SPL)meter for precise level adjustment, setthe volume so that the meter reads75dB, C-Weighting Slow.

NOTE: The subwoofer output level is notadjustable using the test tone. To changethe subwoofer level, follow the steps forOutput Level Trim Adjustment on page 27.

6. When you have adjusted the outputsso that all channels have the samelevel, press the Test Tone button

on the remote or front panelto complete the adjustment.

AVR35 om (H) 2/5/99 10:41 AM Page 19


Delay SettingsOne aspect of the surround modes is thedelay of audio signals between the frontspeakers and the rear speakers. Eachsurround mode is factory preset with aspecific delay time, but it is possible toindividually adjust the delay timing tocustom tailor the sound to your individ-ual taste and the acoustic conditions inyour listening room or home theater.

The factory setting is appropriate formost rooms, but some installationscreate an uncommon distance betweenthe front and surround speakers that maycause the arrival of front channel soundsto become disconnected from surroundchannel sounds.

To resynchronize the front and surroundchannels, follow these steps:

1. Measure the distance from thelistening/viewing position to thefront speakers.

2. Measure the distance from thelistening/viewing position to thesurround speakers.

3. Subtract the distance to the surroundspeakers from the distance to thefront speakers.

a. When setting the delay time for theDolby Digital surround mode, theoptimal delay time is the resultingfigure. For example, if the frontspeakers are ten feet away and thesurround speakers are five feetaway, the optimal delay time isfigured as 105=5. Thus, in thisexample, the delay should be set atfive milliseconds.

b. When setting the delay time for the Pro Logic mode, take the resultof the subtraction and add 15 toobtain the optimal delay time. Forexample, if the front speakers areten feet away and the surroundspeakers are five feet away, theoptimal delay time is figured as 105+15=20. Thus, in thisexample, the delay should be set at twenty milliseconds.

The Dolby Digital mode also provides aseparate setting for the center-channel-delay mode, since the discrete nature of Dolby Digital signals makes thelocation of the center-channel speakermore critical. To calculate the delay forthe center channel, measure the distancefrom the preferred listening position inthe center of the room to both the center-channel speaker and either the left orright speaker.

NOTE: The Theater, Hall 1 and Hall 2modes use a fixed, non-adjustable delay time.

If the distances are equal no furtheradjustment is required and the centerdelay should be set to zero. If the distanceto the front speakers is greater than thedistance to the center speaker you maywish to reposition the speakers by movingthe front left/right speakers closer to thelistening position or the center speakerfurther away from the listening position.

If repositioning of the speakers is notpossible, adjust the center delay time sothat you add one millisecond of center-channel delay for each foot that thedistance to the center speaker lagsbehind the front speakers. For example,if the front left/right speakers are each 10 feet from the listening position andthe center-channel speaker is 8 feet away, the delay is figured as 108=2,suggesting an optimal center delay of 2 milliseconds.

To set the delay times, follow these steps:

1. Put the AVR35 in the Dolby Pro Logicmode by pressing the Dolby ProLogic Selector on the frontpanel, or by pressing the SurroundMode Selector gon the remote,followed by the / buttons huntil PRO LOGIC appears in theMain Information Display S andthe PRO LOGIC indicator F lights.

2. Press the Delay button x on the remote or front panel. The words S DELAY TIMEwill appear in theMain Information Display S .

20

AVR35 om (H) 2/5/99 10:41 AM Page 20



4. Adjust the delay time by pressing the / buttons h on the remote orthe Selector buttons on the frontpanel, until the delay time figure cal-culated using the formula enteredabove appears in the display.

5. If no adjustment is needed for the center-channel delay, press theSet button j to enter thesetting into the AVR35s memory. If the calculations outlined above for the center-0channel delay requirean adjustment, proceed with thefollowing steps:

6. Select a digital input by pressing the Digital button y. Press the / buttons h on the remoteor the Selector buttons on thefront panel until either COAX orDIGITAL appear in the MainInformation Display S. Note thatfor this adjustment, either input maybe selected.


8. Select the Dolby Digital mode eitherby pressing the front panel DolbyDigital Selector( or by pressingthe Surround Mode Selector yon the remote, and then pressing the / buttons h on the remoteuntil DOLBY AC-3 appears in theMain Information Display S .Ignore any NO DATA messagethat may appear.

9. Press the Delay button x onthe remote or front panel. The wordsS DELAY TIME appears in theMain Information Display S .

10. Press the / buttons h on theremote once, so that C DELAYTIME appears in the MainInformation Display S .


12. Press the / buttons h on the remote until the desired delaytime for the center channel appearsin the display.

13. Press the Set button j to enterthe setting into the AVR35s memory.

Congratulations! You have now completedthe setup, adjustment and calibration ofthe AVR35. You are now ready to enjoy thefinest in music and home-theater listening.

21

AVR35 om (H) 2/5/99 10:41 AM Page 21

Operation

Basic Operation

Once you have completed the setup andconfiguration of your new receiver, it issimple to operate and enjoy. The follow-ing instructions will provide the stepsneeded to enjoy the AVR35:

When using the AVR35 for the firsttime, it is necessary to press the MainPower button 1 on the front panel toturn the unit on. This places the unit in astandby mode, as indicated by the ambercolor of the Power Indicator 3 . Oncethe unit is in standby, you may begin alistening session by pressing the SystemPower Control 2 on the front panel orthe Power button d on the remote.Note that the Power Indicator 3 willturn green. This will turn the unit on andreturn it to the input source that was lastused. The unit may also be turned onfrom standby by pressing any of theSource Selector buttons on the remotel or front panel 9)!@#.

To turn the unit off at the end of a listen-ing session simply press the SystemPower Control 2 on the front panelor the Power button d on the remote.Power to any equipment plugged into the rear panel Switched AC Outlet will be shut off and the PowerIndicator 3 will turn amber.

When the remote is used to turn the unitoff it is actually placing the system in astandby mode, as indicated by the ambercolor of the Power Indicator 3.

When you will be away from home for an extended period of time it is always a good idea to completely turn the

unit off using the front panel MainPower Switch 1. Note that all presetmemories are lost if the unit is leftturned off with the Main PowerSwitch 1 for more than two weeks.

Source Selection

To select a source at any time, pressany of the Source Selector buttons on the remote l or front panel 9)!@#.

The front panel Video 3 Inputs 8may be used to connect a device such asa video game or camcorder to your homeentertainment system on a temporarybasis.

When an audio source is selected thelast video input used remains routed tothe Video Outputs 1 and TVMonitor Output . This permitssimultaneous viewing and listening todifferent sources.

During a listening session you maywish to adjust the Bass 5 and Treble6 controls to suit your listening tastes.

Adjust the volume to a comfortablelevel using the front panel VolumeControl or remote VolumeUp/Down buttons.

To temporarily silence all speakeroutputs press the Mute button . This will cut the output to all speakers,but it will not effect any recording ordubbing that may be in progress. Whenthe system is muted the MUTE indicatorA will light in the InformationDisplay . Press the Mute button again to return to normal operation.

For private listening, plug the 1/4"stereo phone plug from a pair of stereoheadphones into the front panelHeadphone jack 4.

When a Video Input source is selectedthe video signal for that input will berouted to the TV Monitor Video Outputjack and will be viewable on a TV mon-itor connected to the AVR35. Make certainthat your TV is set to the proper input toview the signal.

To program the AVR35 for automaticturn off, press the Sleep button e$.Each press of the button will increase thetime before shut down in the followingsequence:

The sleep time will be displayed in theInformation Display and it will countdown until the time has elapsed.

When the programmed time has elapsedthe unit will automatically turn off. Note that the front panel display will dimto one half brightness when the Sleepfunction is programmed. To cancel theSleep function, press the Sleep buttone$ until the information displayreturns to normal brightness and theSleep indicator numbers disappear.

Surround Mode Selection

One of the most important features of the AVR35 is its ability to reproduce a fullmultichannel surround sound field fromDolby Digital sources, analog matrix surround encoded programs and stan-dard stereo programs. In all a total ofseven listening modes are available onthe AVR35.

90min

80min

70min

60min

50min

40min

30min

20min

10min

5min

1min OFF

22

AVR35 om (H) 2/5/99 10:41 AM Page 22

Operation

Selection of a surround mode is based onpersonal taste, as well as the type of pro-gram source material being used. Forexample, motion pictures or TV programsbearing the logo of one of the major sur-round encoding processes, such as DolbySurround, DTS Stereo or UltraStereomay be played in either the Dolby Digital,Dolby Pro Logic or Movie Surrounddepending on the source material.

23

MODE

DOLBY DIGITAL

DOLBY PRO LOGIC

DOLBY 3 STEREO

THEATER

HALL 1 and HALL 2

STEREO

FEATURES

This mode is available only when the source material is encoded with Dolby Digital(AC-3) data. It provides up to five separate main audio channels and a special dedi-cated Low-Frequency Effects channel.

Dolby Pro Logic is the standard mode for analog surround sound decoding. It uses information encoded in a two-channel stereo recording to produce four distinct channels: Left, Center, Right and Surround. Use this mode for accurate reproductionof programs bearing the Dolby Surround, DTS Stereo, UltraStereo or otherSurround logos. Surround encoded programs include videocassette, DVD and LDmovies, TV and cable programs, radio programs and audio CDs. Dolby Pro Logic processing may also be used to provide a pleasing surround effect with some stereophonic source material that does not carry surround encoding.

Dolby 3 Stereo uses the information contained in a surround encoded or two-channelstereo program to create center-channel information. In addition, the informationthat is normally sent to the rear channel surround speakers is carefully mixed in withthe front left and right channels for increased realism. Use this mode when you have acenter-channel speaker, but no surround speakers.

Theater Surround processing uses matrix surround decoding to simulate a standardmovie or stage theater.

These modes are designed for use with stereo recordings. They provide a sound-fieldeffect that simulates the complex combination of direct and reflected sounds that create the rich reverberant atmosphere of a medium-sized concert hall (Hall 1) or alarger concert hall (Hall 2).

This mode turns off all surround processing and presents the pure left and right channel presentation of two channel stereo programs.

DELAY TIME RANGE

Center: 0 ms 5 msSurround: 0 ms 15 ms

15 ms 30 msInitial Setting = 20 ms

No Surround Channels

Fixed at 27 ms

Hall 1 Fixed at 41 msHall 2 Fixed at 67 ms

No Surround Channels

Surround Mode Chart

NOTE: Once a program has beenencoded with surround information, itretains the surround matrix as long asthe program is broadcast in stereo. Thus,movies with surround sound will carrysurround information when they arebroadcast via conventional TV stations,cable, pay TV and satellite transmission.In addition, a growing number of made-for-television programs, sports broad-casts, radio dramas and music CDs arealso recorded in surround sound. You

may obtain a list of these programs anddiscs from the Dolby Laboratories website at www.dolby.com

When a program is not listed as carryingintentional surround information, youmay find that Pro Logic or Dolby 3-Stereomodes often deliver enveloping surroundpresentations through the use of thenatural information present in all stereorecordings. However, for stereo, but non-surround programs, we suggest that youtry the Hall 1, Hall 2 or Theater modes.

AVR35 om (H) 2/5/99 10:41 AM Page 23

Operation

Surround modes are selected using eitherthe front panel controls or the remote. Toselect a surround mode from the frontpanel, simply press the button that corre-sponds to the desired mode (. To select a surround mode using theremote, press the Surround ModeSelector g, and then press the /buttons h to change the mode. As you press the buttons, the surround mode name will appear in the MainInformation Display S, and anindividulal mode indicator will also light up D /F /J.

Note that the Dolby Digital Mode mayonly be selected when a Dolby Digitalsource is playing. For more informationon Dolby Digital, see the following sectionof this manual.

To listen to a program in traditional two-channel stereo, using the front left andfront right speakers only (plus the sub-woofer if installed and configured), pressthe Surround Off button on thefront panel, or follow the insturctionsshown above for using the remote untilSURR OFF appears in the MainInformation Display S. When theAVR35s surround circuits are turned off,and it is in the Stereo mode, the BYPASSindicator B will illuminate in theInformation Display .

Digital Audio Playback

Dolby DigitalDolby Digital (also known as AC-3) is thelatest advancement in surround-soundtechnology, delivering up to five full-range surround channels (left, center,right, left surround and right surround)plus a special dedicated Low-FrequencyEffects (LFE) channel. This represents amajor advancement over traditionalanalog surround in that each surroundchannel is fully discrete and capable offull bandwidth reproduction. DolbyDigital is available on DVD and LV discs,and it will be a part of the new high-definition television (HDTV) systemwhen digital broadcasting begins in1998. Dolby Digital for the home is basedon the same system used to deliver digitalaudio sound tracks in movie theaters,enabling true cinema reproduction inyour home.

To utilize the Dolby Digital mode youmust have a digital source properlyconnected to the AVR35. Connect theDigital datastream outputs from DVDplayers, HDTV receivers and CD players tothe AC-3/PCM Coaxial or Opticalinputs on the rear panel . In orderto provide a backup signal and a sourcefor recording, the analog outputs providedon digital source equipment should alsobe connected to their appropriate inputson the AVR35 rear panel (e.g., connect theanalog stereo audio output from a DVD tothe DVD inputs on the rear panelwhen you connect the digital outputs.)

When playing back a digital source, firstselect the input using the remote or frontpanel controls as outlined above. Nextselect the digital source by pressing theappropriate Digital Input button y and then using the / buttons gon the remote or the Selector buttons on the front panel to choose eitherCOAXIAL or DIGITAL, as it appearsin the Main Information Display S.Press the Set button j to enter thedesired choice. When the digital source is playing, the AVR35will automatically detect if it is a multi-channel Dolby Digital source or a con-ventional PCM signal, which is thestandard output from CD players. Anindicator will light in the InformationDisplay to confirm the digital signal isAC-3 H or PCM I and if the source isOPTICAL E or COAX G.

When an AC-3 source is playing, theAVR35 will automatically switch to theDolby Digital surround mode. It is impor-tant to note, however, that not all AC-3sources are encoded with the full comple-ment of five channels plus LFE. When adigital source is playing, the MainInformation Display S will change toshow the input source and digital type(OPTICAL or COAX). When a source withDolby Digital encoding is playing, theinput source name will appear in theInformation Display, followed by anumeric key to the type and number of channels being decoded as follows:

24

AVR35 om (H) 2/5/99 10:41 AM Page 24

Operation

3/2.1: This message appearswhen a full complement of DolbyDigital signals is present: 3 frontchannels (left, center and right), 2 surround channels (surround left and surround right) and 1channel, which is the dedicated Low-Frequency Effects (LFE) channel.

3/1: This message indicates theAC-3 system is decoding a standardDolby Pro Logic signal with left,center and right front channels and a signal mono surround channel.

2/0: This message indicates thatthe AC-3 system is decoding a tradi-tional two-channel stereo signal andthat no center, surround or LFEsignals are present.

1+1: This is a monaural signalthat plays the same information inboth the left front and right frontspeakers. There is no sound sent tothe center or surround speakers.

1/0: This is a monaural signalthat plays through the center channelspeaker only. There is no sound at thefront left/right or surround speakers.

Night ModeA special feature of Dolby Digital is theNight mode, which enables AC-3 inputsources to be played back with their fullrange while reducing the minimum peaklevel by 1/4 to 1/3. This prevents abruptlyloud transitions from causing distur-bances without reducing the impact ofthe digital source. The Night mode isavailable only when AC-3 signals withspecial data are being played.

To engage the Night mode, press theNight buttonk on the remote andnote that the NIGHT indicator K willilluminate in the Information Display.

IMPORTANT NOTES ON DOLBY DIGITAL PLAYBACK:

1. When the digital playback unit is in apause, fast forward or chapter searchmode the digital audio data maymomentarily stop, causing a NO DATAmessage to be displayed. This is normaland does not indicate a problem witheither the AVR35 or the source machine.The AVR35 will return to DolbyDigital/AC-3 playback as soon as the datais available when the machine is in astandard play mode.

2. The AVR35 will decode digital audiosources with a sampling frequency of32kHz, 44.1kHz and 48kHz. Althoughthis will enable it to decode virtually allDVD movies and HDTV sources, it is pos-sible that some future digital sourcesmay not be compatible with the AVR35.

NOTE: In order to play the Dolby Digitalsignals that are recorded on laser discs,you must have both a laser disc playerwith an RF output, and an optional,outboard RF-to-data demodulator. Tolisten to Dolby Digital LV discs, connectthe AC-3/RF output of the player to thedemodulator, and connect the output of the demodulator to the Coaxial orOptical inputs on the rear panelof the AVR35. DO NOT connect the AC-3/RF output of a laser disc playerdirectly to the AVR35.

3. Note that not all programs recorded inDolby Digital contain full 5.1 channelaudio. Consult the program guide thataccompanies the DVD or laser disc todetermine which type of audio has beenrecorded on the disc. The AVR35 willautomatically sense the type of digitalsurrround encoding used on an AC-3program source and adjust toaccommodate it.

4. When a Dolby Digital source isplaying, you may not select any of theanalog surround modes.

5. It is not possible to record the outputof a Dolby Digital program.

PCM Audio PlaybackPCM (Pulse Code Modulation) is thenon-compressed digital audio systemused for compact discs and non-AC-3laser discs. The digital circuits in theAVR35 are capable of high-quality digital-to-analog decoding, and they may beconnected directly to the digital audiooutput of your CD or LV player.

Connections should be made to the AC-3/PCM Optical or Coaxial inputs on the rear panel, using whicheverinput is not occupied by an AC-3 sourcesuch as a DVD player.

To listen to a PCM digital source, firstselect the input for the desired source(e.g., CD). Next press the Digital buttony and then using the / buttonsh on the remote or the Selectorbuttons on the front panel until thedesired choice of either COAXIALorDIGITAL, as it appears in the MainInformation Display S. Press the Setbutton j to enter the desired choice.

25

AVR35 om (H) 2/5/99 10:41 AM Page 25

Operation

When a PCM source is playing, the PCMindicator I will light, and the MainInformation Display will show the inputsource and the digital type. During PCMplayback you may select any surroundmode except Dolby Digital.

Tuner Operation

The AVR35s tuner is capable of tuningAM, FM and FM Stereo broadcast stations.Stations may be tuned manually, or theymay be stored as favorite station presetsand recalled from a 30-position memory.

Station Selection1. Press the AM/FM button #l toselect the tuner as an input.

2. Press the AM/FM button #l againto switch between AM and FM so that thedesired frequency band is selected.

3. Press the Tuner Mode button *rto select manual or automatic tuning.

When the AUTO indicator O is illumin-ated in the Main Information Display thetuner will only stop at those stations thathave a strong enough signal to bereceived with acceptable quality.

When the MONO indicator Q is illumin-ated, the tuner is in a manual mode andwill stop at each frequency increment inthe selected band.

4. To select stations press the Tuningbutton %v. When the AUTO indicatorO is illuminated each press will causethe tuner to search for the next highestor lowest frequency station that has anacceptable signal. When tuning FM sta-tions in the Auto mode, the tuner willonly select Stereo stations. To tune to the

next station, press the button again. Ifthe MONO indicator Q is illuminated,tap the Tuning button %v toadvance one frequency increment at atime, or press and hold it to locate a spe-cific station. When the TUNED indicatorR illuminates, the station is properlytuned and should be heard with clarity.

5. Stations may also be tuned directly by pressing the Direct button s, andthen pressing the Numeric Keys nthat correspond to the stations frequency.The desired station will automatically be tuned.

NOTE: When the FM reception of astation is weak, audio quality will beincreased by switching to Mono mode by pressing the Tuner Mode button *r until the STEREO indicator Pgoes out.

Preset TuningUp to 30 stations may be stored in theAVR35s memory for easy recall using thefront panel controls or the remote.

To enter a station to the memory, firsttune the station using the steps outlinedabove. Then:

1. Press the Memory button q on the remote. Note that MEMORY indicatorN will illuminate and flash in theInformation Display.

2. Within five seconds, press theNumeric Keys n corresponding tothe location where you wish to store thisstations frequency.

3. Repeat the process after tuning anyadditional stations to be preset.

Recalling Preset Stations To manually select a station previouslyentered in the preset memory, press theNumeric Keys n that correspond tothe desired stations memory location.

To manually tune through the list ofstored preset stations one by one, pressthe Preset buttons &u on the frontpanel or remote.

To automatically scan through the sta-tions entered in the preset memory, pressthe Preset Scan button ^ on the frontpanel. The tuner will run through the listof preset stations, stopping for five secondsat each one. Press the button again to stopthe scan at your desired station.

Tape Recording

In normal operation, the audio or videosource selected for listening through theAVR35 is sent to the record outputs. This means that any program you arewatching or listening to may be recordedsimply by placing machines connected to the outputs for Tape Monitor b orVideo One in the record mode.

When a tape recorder with separate recordand playback heads is used, you maymonitor the output of the recording byselecting the Tape Selector 9l.Note that a red LED will illuminate in thefront panel above the Tape Selector 9to remind you that you are listening tothe record playback instead of the actualinput source being recorded.

NOTE: It is not possible to record theoutput of Dolby Digital programs.

26

AVR35 om (H) 2/5/99 10:41 AM Page 26

Operation

IMPORTANT NOTE: Please make cer-tain that you are aware of the copyrightrestrictions on any material you copy.Unauthorized duplication of copyrightedmaterials is prohibited by Federal law.

Output Level Trim Adjustment

Normal output level adjustment for theAVR35 is established using the Test Tone,as outlined on page 19. In some cases,however, it may be desirable to adjust theoutput levels using program materialsuch as a test disc, or a selection you arefamiliar with. Additionally, the outputlevel for the subwoofer may only beadjusted using this procedure.

To adjust the output levels using pro-gram material, first set the referencevolume for the front left/right chann

Harman Kardon AVR35

Documents

Transcript of Harman Kardon AVR35