Hardware and Commissioning Checklist PTN 910 v3.0

8/10/2019 Hardware and Commissioning Checklist PTN 910 v3.0

1/17


2/17

HARDWARE AND COMMISSIONING CHECKLISTHUAWEI PTN 910 MODEL NETWORK 3G

Version 3 HUAWEI Proprietary and Confidential Page 2 of 17

DISTRIBUTE PTN 910 GENERAL INFORMATION

In the physical board and in the ODUs take the serial numbers and fill the following table:

SLOT HARDWARE SERIAL NUMBER

IDU sub-rack Order: No:

1 CXPA 16 digits

2 CXPA 16 digits

3 IFE 2 16 digits

4 IFE 2 16 digits

5 PIU 16 digits

6 FAN 16 digits

ODU Main ODU 20 digits

ODU Stand by ODU 20 digits

Access to the IDU and export the Board Information Report


3/17



CHAPTER I

HARDWARE INSTALLATION PROTOCOL

1. CABINET INSTALLATION INSPECTION

1.1No parts on the cabinets are damaged or detached. No cables are

damaged or snappedNO YES N/A

1.2 Verify that the equipment metal supports dont have oxide trace NO YES N/A

1.3Equipment installed according to the TSS and/or customer

recommendations.NO YES N/A

1.4The supports are positioned and spaced in accordance with the

drawing of the installation holes. (This item applies to the cabinet

installation on the ESD floor.)

NO YES N/A

1.5All supports are fixed to the floor correctly. (This item applies to the

cabinet installation on the ESD floor.)NO YES N/A

1.6All components of the supports are installed correctly. (This item

applies to the cabinet installation on the ESD floor.)NO YES N/A

1.7All floor holders are installed at the same height. (This item applies

to the cabinet installation on the ESD floor supported by floor

holders.)

NO YES N/A

1.8 Each cabinet is well insulated from the support or the floor. NO YES N/A

1.9All cabinet accessories are installed, including front door, back

door, and side doors.NO YES N/A

1.10The row labels, column labels, and product labels are attached to

the specified positions.NO YES N/A

1.11The ESD wrist strap is connected to the ESD bonding point on the

cabinet.NO YES N/A

1.12 Insulation is performed for shockproof parts between multiple rowsof cabinets.NO YES N/A

1.13All bolts are fixed with flat washers and spring washers in a correct

order.NO YES N/A

1.14 The cabinets are stable and orderly. NO YES N/A


4/17



1.15 The cabinet its correctly aligned NO YES N/A

1.16All cabinet side doors facing the aisle are aligned with the error less

than 5 mm. NO YES N/A

1.17The surfaces of the cabinets are clean without any fingerprint or

smudge. There is no dust, excessive cable tie ends or other

sundries either inside or outside each cabinet.

NO YES N/A

1.18 All kinds of labels are correct, legible and intact. NO YES N/A

1.19 The front and back doors of the cabinets are easy to open or close. NO YES N/A

1.20 The modules in one cabinet are aligned from the top down. NO YES N/A

1.21 All the filler panels are installed. NO YES N/A

1.22All Subracks are installed in proper positions, and their DIP

switches are properly set.NO YES N/A

1.23 No paint is detached. NO YES N/A

2. CABLE INSTALLATION INSPECTION

2.1 Power and PGND cables

2.1.1The -48 V power cables are blue, the PTN 910 power cables are

black, and the PGND cables are green and yellow. The power

cables shall meet the field requirements.

NO YES N/A

2.1.2All the core wires of the power cables and PGND cables are

made of copper.NO YES N/A

2.1.3 No power cable or PGND cable is damaged or snapped. NO YES N/A

2.1.4 No welding point exists in the power cables and PGND cables. NO YES N/A

2.1.5No breaking device such as the switch or fuse exists in the

electric connection of the grounding system.NO YES N/A


5/17



2.1.6The power cables and PGND cables of extra length are trimmed

rather than coiled.NO YES N/A

2.1.7The grounding bars and PGND bars are finally connected to one

grounding conductor.NO YES N/A

2.1.8The grounding bar of the PDB is well connected to the grounding

bar provided by the customer.NO YES N/A

2.1.9The output current values of the PDB and the DC power

distribution panel meet the requirements.NO YES N/A

2.1.10All power cables and PGND cables are not short-circuited or

reversely connected.NO YES N/A

2.1.11 The OT terminals of the power cables and PGND cables arewelded or crimped securely.NO YES N/A

2.1.12

The power cables and PGND cables connecting the power

distribution box with the functional modules, and the PGND

cables connecting the modules with the grounding bar are all

correctly installed and have satisfactory contact.

NO YES N/A

2.1.13The front, back, and side doors are respectively connected to the

grounding bolts on the lower enclosure of the cabinet through the

6 mm2green and yellow cables.

NO YES N/A

2.1.14

The power cables and PGND cables are laid straight and bound

orderly in the cabinets or in the PDB. Each switch on the PDB ismarked with the number of the corresponding cabinet.

NO YES N/A

2.1.15Engineering labels are attached to both ends of each power

cable or PGND cable.NO YES N/A

2.1.16The power cable of the alarm box laid on a wall is in a PVC

trough.NO YES N/A

2.1.17 Power Test. NO YES N/A


6/17



3. MW ANTENNA SYSTEM INSTALLATION INSPECTION

3.1 Mw system Installation Inspection

3.1.1Equipment installed according

to the TSS and/or customer

recommendations.

NO YES N/A

3.1.2

Equipments correctly aligned,

fixed and fit in their supports, inorder to avoid interfering with

any existing infrastructure.

BREAKERS NO YES N/A

IDU NO YES N/A

ODUs NO YES N/A

ANTENA NO YES N/A

POLE NO YES N/A

3.1.3The antenna support is securely

connected to the tower or the

rooftop.

NO YES N/A

3.1.4

The labelsare attached orderly and

neatly to the feeders and jumpers.

They face the same direction

according to the specifications.

NO YES N/A

3.1.5Correspondence of the IF cable

with the ODUs according to the

configuration of the protection.

IF 1

NO YES N/A

IF 2

NO YES N/A

3.1.6 -48 VDC PTN 910 power cableis correctly installed.

POWER CABLE 1

NO YES N/A

POWER CABLE 2 NO YES N/A

3.1.7The IF cables are correctly

connected.NO YES N/A


7/17



3.1.8

All outdoor jumper connectors

are waterproofed and sealed.

Waterproof curves are made for

the jumpers.NO YES N/A

3.1.9

A certain length of ties is kept

when you cut the ties after

binding all the outdoor jumpers.NO YES N/A

3.1.10Grounding cable installed with

terminals correctly fit, and

conductive grease applied.

IDU NO YES N/A

ODU 1 NO YES N/A

ODU 2 NO YES N/A

IF CABLE NO YES N/A

3.1.11Curvature radius of IF's cables

fulfills with the manufacturer

specifications.NO YES N/A

3.1.12Verify to cut properly the plastichatbands after the cables are

aligned and groupsNO YES N/A

3.1.13The TBN connector is protected

with insulating tape and

waterproof tape.NO YES N/A


8/17



3.1.14 The labels are correctly pastedin the following equipments:

PTN:

Power-PTNNO YES N/A

Sub-RACK NO YES N/A

GND NO YES N/A

ODU:

ODU 1 NO YES N/A

ODU 2 NO YES N/A

GND NO YES N/A

IF CABLES NO YES N/A

Transmission Cables:

Ethernet Tx NO YES N/A

BREAKERS:

-48VDC NO YES N/A

GND NO YES N/A

3.1.15Antennas azimuths are

according to customer

requirement

NO YES N/A


9/17


10/17



CHAPTER II

COMMISSIONING TEST PROTOCOL

Test Items for Preliminary Test

Interface and System Test Item Test Sub-Item

System function test Hardware performance Alarm management

Actual transmit frequency of the ODU

Actual receive frequency of the ODU

Actual transmit power of the ODU

RF parameter configuration

Actual receive power of the ODU

IF/RF test

Microwave protection HSB switching

IDU Power Protection IDU board protection 1+1 Power Protection Board


11/17


12/17


13/17



2.2 IDU Power protection

2.2.1 IDU board protection - 1+1 Power Protection Board

Test Sub-Item HSB Switching

Node No. Function Test Conclusion

Turn-off the main breaker and check thepower status of the IDU. NO YES

N/A

Turn-off the protection breaker and checkthe power status of the IDU NO YES

N/A

Indexes:

Remarks:


14/17


15/17


16/17



HARDWARE AND COMMISSIONING ACCEPTANCECERTIFICATE

This document certifies that equipments passed the inspection according internal order.

Network Element PTN 910

Site Local Name

Site Remote Name

Contract Name NII 3G Per Project

Comments:

Inspection Date:

Company:

Huawei del Per S.A.C.

Customer:

Nextel del Per S.A. Cooperator in charge:

Name: Name:

Title: Title:

Signature: Signature:

Place & Date: Place & Date:


17/17



HARDWARE AND COMMISSIONING FINAL ACCEPTANCECERTIFICATE

This document certifies that equipments passed the inspection according internal order.

Network Element PTN 910

Site Local Name

Site Remote Name

PO Number

Contract Name NII 3G Per Project

Huawei Internal Contract Number

Comments:

Customer :

NEXTEL DEL PER S.A.

Company:

HUAWEI DEL PER S.A.C.

Name:

GUSTAVO REY-SANCHEZ

Name:

EDUARDO ZEVALLOS

Title:

OVERALL ENGINEERING PROJECT MANAGER

Title:

OVERALL PROJECT MANAGER

Signature: Signature:

Place & Date :

Lima, , 2009

Place & Date:

Lima, , 2009

Hardware and Commissioning Checklist PTN 910 v3.0

Documents

Transcript of Hardware and Commissioning Checklist PTN 910 v3.0