Hanging 4x4 Post-It Note Holder

Tutorial Created by Maria BellImages are copyrighted and the property of Maria Bell

  

  

 

(2) 4x4" chipboard coasters(2) 4x4" designer paper (Autumn Vine)

1 Post It Note1 Large Clip

3/4" round magnet(2) 3" ribbon

Ribbon to tie a bowDouble stick tape/transfer tape

3.1/4" square card stock (Chocolate Chip)

Materials 

Page 1 of 7Hanging 4x4 Post-It Note Holder

2/20/2009file://C:\Documents and Settings\Maria\My Documents\Tutorials PDF\Hanging 4x4 Post.htm

3 x 3" photoLiquid glue or hot glue

Sanding block (optional)

Design Option:

Prima flowersPhoto Corner Punch

 

 Apply sticky tape or double stick tape to the chipboard coasters shown in the picture.

 

 Adhere the 3" ribbons to the chipboard coasters as shown in the picture. Leave a gap of

1 1/4" between the two coasters.

Depending on your design, you may place one 3" ribbon in the center rather than 2 side by side ribbons. 

Page 2 of 7Hanging 4x4 Post-It Note Holder

2/20/2009file://C:\Documents and Settings\Maria\My Documents\Tutorials PDF\Hanging 4x4 Post.htm

 Adhere the designer papers to the 2 coasters over the ribbons and sand the edge.  

Sanding the edge is optional but it keeps the designer paper from peeling off the edge or fraying but it's not necessary. 

 Apply glue or double stick tape to the back of the post-it note and adhere to one of the chipboard coasters on the designer

paper side. 

 Apply liquid glue or hot glue to one side of the inner aspect of the clip (hot glue has a stronger hold).

Sorry for the poor quality of the photo. 

Page 3 of 7Hanging 4x4 Post-It Note Holder

2/20/2009file://C:\Documents and Settings\Maria\My Documents\Tutorials PDF\Hanging 4x4 Post.htm

 Add the clip to the top of the chipboard coaster over the post it note.  Be sure the side with the glue is on the back side of

the chipboard coaster and not on the side of the post-it note.

 

 Apply liquid glue or hot glue to one side of the 3/4" round magnet

 

 Apply the magnet to the back side of the clip as shown in the photo.

 

Page 4 of 7Hanging 4x4 Post-It Note Holder

2/20/2009file://C:\Documents and Settings\Maria\My Documents\Tutorials PDF\Hanging 4x4 Post.htm

 If the "squeeze" component of the clip is not solid as shown in the clip in the previous picture, apply the magnet to the

"solid" part of the clip as shown in the picture. 

  

Tie a ribbon to one of the "squeeze" component of the clip (front side)  not around both components or you'll have problems squeezing the clip.

  

 Mat your 3x3" square photo to the 3 1/4 x 3 1/4" card stock

Page 5 of 7Hanging 4x4 Post-It Note Holder

2/20/2009file://C:\Documents and Settings\Maria\My Documents\Tutorials PDF\Hanging 4x4 Post.htm

  

Design Option:

Adhere to the center of the 2nd chipboard coaster (bottom coaster)

Punch a large and small photo corners using the SU Photo Corner Punch and adhere to the left top corner over the photo.

Adhere the Prima flowers to the right lower corner as shown in the photo  

 Design Option:

If you prefer to use a ribbon to hang the post-it note holder rather than using a magnet.  Punch two holes to the top left and right corners and attach a large eyelet to each of the holes.

Page 6 of 7Hanging 4x4 Post-It Note Holder

2/20/2009file://C:\Documents and Settings\Maria\My Documents\Tutorials PDF\Hanging 4x4 Post.htm

 Loop a ribbon through the holes and tie the ends at the back of the chipboard coaster as shown in the picture.

 

  

Page 7 of 7Hanging 4x4 Post-It Note Holder

2/20/2009file://C:\Documents and Settings\Maria\My Documents\Tutorials PDF\Hanging 4x4 Post.htm