Handoff Schemes Overview and Guidelines for Handoff Procedures ...
Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth,...
-
Upload
marian-hodge -
Category
Documents
-
view
221 -
download
0
description
Transcript of Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth,...
![Page 1: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/1.jpg)
Handoff Support for Mobility with IP over Bluetooth
Simon Baatz Matthias Frank Rolf Gopffarth Peter Martini Markus Schetelig Dmitri Kassatkine Asko VilavaaraUniversity of BonnNokia Mobile Phones Produktionsgesellschaft mbH RampD Center GermanyNokia Research Center P 0 Box 407 FIN-00045 Nokia Group Finland
2000 IEEE
Outline Introduction Bluetooth amp BLUEPAC Handoff support Prototyping Conclusons
Introduction To overcome the Bluetooth short range wireless communication In a BLUEPAC mobile Bluetooth devices can move between different APs while still being addressable via the same IP address
Bluetooth amp BLUEPAC Bluetooth is a low-cost low-power
A slotted protocol with a FHSS (Frequency Hopping Spread Spectrum) in 24 GHz
The hop frequency is 1600 hops per second the frequency spectrum is divided into 79 channels of 1 MHz bandwidth each
Bluetooth amp BLUEPAC Each Bluetooth device has 48-bit address
Bluetooth amp BLUEPAC A strict master-slave scheme A device acting as master can have up to 7 active slaves connected Master and slaves form a so-called piconet
Master defines the timing and the hop pattern Slaves have to stay synchronized to the master
Bluetooth amp BLUEPAC Link support
Synchronous Connection Oriented (SCO) links (typically used for voice)
and an Asynchronous Connectionless link (ACL) Time Division Duplex (TDD)
Bluetooth amp BLUEPAC Masterslave establish connection1048766
Master enters inquiry state Master send inquiry command two times in one time slot Slave in inquiry scan state will send its 48 bits bluetooth address to master
Master enters Page state Master sends to slave 48-bit Address and clk (for computing hopping sequence)
Bluetooth amp BLUEPAC
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 2: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/2.jpg)
Outline Introduction Bluetooth amp BLUEPAC Handoff support Prototyping Conclusons
Introduction To overcome the Bluetooth short range wireless communication In a BLUEPAC mobile Bluetooth devices can move between different APs while still being addressable via the same IP address
Bluetooth amp BLUEPAC Bluetooth is a low-cost low-power
A slotted protocol with a FHSS (Frequency Hopping Spread Spectrum) in 24 GHz
The hop frequency is 1600 hops per second the frequency spectrum is divided into 79 channels of 1 MHz bandwidth each
Bluetooth amp BLUEPAC Each Bluetooth device has 48-bit address
Bluetooth amp BLUEPAC A strict master-slave scheme A device acting as master can have up to 7 active slaves connected Master and slaves form a so-called piconet
Master defines the timing and the hop pattern Slaves have to stay synchronized to the master
Bluetooth amp BLUEPAC Link support
Synchronous Connection Oriented (SCO) links (typically used for voice)
and an Asynchronous Connectionless link (ACL) Time Division Duplex (TDD)
Bluetooth amp BLUEPAC Masterslave establish connection1048766
Master enters inquiry state Master send inquiry command two times in one time slot Slave in inquiry scan state will send its 48 bits bluetooth address to master
Master enters Page state Master sends to slave 48-bit Address and clk (for computing hopping sequence)
Bluetooth amp BLUEPAC
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 3: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/3.jpg)
Introduction To overcome the Bluetooth short range wireless communication In a BLUEPAC mobile Bluetooth devices can move between different APs while still being addressable via the same IP address
Bluetooth amp BLUEPAC Bluetooth is a low-cost low-power
A slotted protocol with a FHSS (Frequency Hopping Spread Spectrum) in 24 GHz
The hop frequency is 1600 hops per second the frequency spectrum is divided into 79 channels of 1 MHz bandwidth each
Bluetooth amp BLUEPAC Each Bluetooth device has 48-bit address
Bluetooth amp BLUEPAC A strict master-slave scheme A device acting as master can have up to 7 active slaves connected Master and slaves form a so-called piconet
Master defines the timing and the hop pattern Slaves have to stay synchronized to the master
Bluetooth amp BLUEPAC Link support
Synchronous Connection Oriented (SCO) links (typically used for voice)
and an Asynchronous Connectionless link (ACL) Time Division Duplex (TDD)
Bluetooth amp BLUEPAC Masterslave establish connection1048766
Master enters inquiry state Master send inquiry command two times in one time slot Slave in inquiry scan state will send its 48 bits bluetooth address to master
Master enters Page state Master sends to slave 48-bit Address and clk (for computing hopping sequence)
Bluetooth amp BLUEPAC
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 4: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/4.jpg)
Bluetooth amp BLUEPAC Bluetooth is a low-cost low-power
A slotted protocol with a FHSS (Frequency Hopping Spread Spectrum) in 24 GHz
The hop frequency is 1600 hops per second the frequency spectrum is divided into 79 channels of 1 MHz bandwidth each
Bluetooth amp BLUEPAC Each Bluetooth device has 48-bit address
Bluetooth amp BLUEPAC A strict master-slave scheme A device acting as master can have up to 7 active slaves connected Master and slaves form a so-called piconet
Master defines the timing and the hop pattern Slaves have to stay synchronized to the master
Bluetooth amp BLUEPAC Link support
Synchronous Connection Oriented (SCO) links (typically used for voice)
and an Asynchronous Connectionless link (ACL) Time Division Duplex (TDD)
Bluetooth amp BLUEPAC Masterslave establish connection1048766
Master enters inquiry state Master send inquiry command two times in one time slot Slave in inquiry scan state will send its 48 bits bluetooth address to master
Master enters Page state Master sends to slave 48-bit Address and clk (for computing hopping sequence)
Bluetooth amp BLUEPAC
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 5: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/5.jpg)
Bluetooth amp BLUEPAC Each Bluetooth device has 48-bit address
Bluetooth amp BLUEPAC A strict master-slave scheme A device acting as master can have up to 7 active slaves connected Master and slaves form a so-called piconet
Master defines the timing and the hop pattern Slaves have to stay synchronized to the master
Bluetooth amp BLUEPAC Link support
Synchronous Connection Oriented (SCO) links (typically used for voice)
and an Asynchronous Connectionless link (ACL) Time Division Duplex (TDD)
Bluetooth amp BLUEPAC Masterslave establish connection1048766
Master enters inquiry state Master send inquiry command two times in one time slot Slave in inquiry scan state will send its 48 bits bluetooth address to master
Master enters Page state Master sends to slave 48-bit Address and clk (for computing hopping sequence)
Bluetooth amp BLUEPAC
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 6: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/6.jpg)
Bluetooth amp BLUEPAC A strict master-slave scheme A device acting as master can have up to 7 active slaves connected Master and slaves form a so-called piconet
Master defines the timing and the hop pattern Slaves have to stay synchronized to the master
Bluetooth amp BLUEPAC Link support
Synchronous Connection Oriented (SCO) links (typically used for voice)
and an Asynchronous Connectionless link (ACL) Time Division Duplex (TDD)
Bluetooth amp BLUEPAC Masterslave establish connection1048766
Master enters inquiry state Master send inquiry command two times in one time slot Slave in inquiry scan state will send its 48 bits bluetooth address to master
Master enters Page state Master sends to slave 48-bit Address and clk (for computing hopping sequence)
Bluetooth amp BLUEPAC
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 7: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/7.jpg)
Bluetooth amp BLUEPAC Link support
Synchronous Connection Oriented (SCO) links (typically used for voice)
and an Asynchronous Connectionless link (ACL) Time Division Duplex (TDD)
Bluetooth amp BLUEPAC Masterslave establish connection1048766
Master enters inquiry state Master send inquiry command two times in one time slot Slave in inquiry scan state will send its 48 bits bluetooth address to master
Master enters Page state Master sends to slave 48-bit Address and clk (for computing hopping sequence)
Bluetooth amp BLUEPAC
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 8: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/8.jpg)
Bluetooth amp BLUEPAC Masterslave establish connection1048766
Master enters inquiry state Master send inquiry command two times in one time slot Slave in inquiry scan state will send its 48 bits bluetooth address to master
Master enters Page state Master sends to slave 48-bit Address and clk (for computing hopping sequence)
Bluetooth amp BLUEPAC
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 9: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/9.jpg)
Bluetooth amp BLUEPAC
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 10: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/10.jpg)
Bluetooth amp BLUEPAC
Cellular IP Router
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 11: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/11.jpg)
Bluetooth amp BLUEPAC
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 12: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/12.jpg)
Handoff support The layer 2 which are supported
mobility of Bluetooth devices in a BLUEPAC network
The IP Adaptation Layer which is inserted between IP and L2CAP to provide a suitable data link layer
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 13: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/13.jpg)
Handoff support
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 14: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/14.jpg)
Handoff support-IP Adaptation Layer for mobile devices
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 15: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/15.jpg)
Handoff support-IP Adaptation Layer for Base Station
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 16: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/16.jpg)
Handoff support Another important job is to detect a
possible handoff Link supervision timer
the default value for the Link supervision timer is 20 seconds Too small value has the effect of tearing down
a connection too early and thus wasting time for reconnecting
Too large value has the affect that time is
wasted by regarding a link as alive despite being out of range of the Base Station
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 17: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/17.jpg)
Handoff support
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 18: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/18.jpg)
Prototyping
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 19: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/19.jpg)
Prototyping The prototyping system showed that
Bluetooth devices are able to successfully move between different Base Stations and keep existing higher layer connections alive
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-
![Page 20: Handoff Support for Mobility with IP over Bluetooth Simon Baatz, Matthias Frank, Rolf Gopffarth, Peter Martini, Markus Schetelig, Dmitri Kassatkine, Asko.](https://reader033.fdocuments.us/reader033/viewer/2022051301/5a4d1ae67f8b9ab0599792ec/html5/thumbnails/20.jpg)
Conclusons Handoff performance is strongly dependent on the time by the broken link detection An ideal value for the link supervision timer is still an open issue
- Slide 1
- Slide 2
- Slide 3
- Slide 4
- Slide 5
- Slide 6
- Slide 7
- Slide 8
- Slide 9
- Slide 10
- Slide 11
- Slide 12
- Slide 13
- Slide 14
- Slide 15
- Slide 16
- Slide 17
- Slide 18
- Slide 19
- Slide 20
-