Contents

1

H. Andersen A/S 2.

Traction belts 3.

Low profile/high profile traction belts 4.

Bars 5.

Standard sieve webs 6.

Special sieve webs 7.

Hedgehog webs 8.

Joining methods 9. -10.

Bar covering 11.

Protection from damage 12.

Drive wheels 13. -14.

Friction drive 15.

Rollers 16.

Shakers 17.

Rubber flights 18.

Steel flights 19.

Availability 20.

H. Andersen A/SCompany profile

2

H. Andersen A/S is founded in 1984 with the purpose to sell good, cheap unoriginal parts for potatoharvesters. Today we sell 60% to eksport.

Since the start we have expanded our line of products to cover spareparts/wearparts for stonecollectors, beetharvesters and various specialmaschines.

H. Andersen A/S offer an almost complete line of webs, drive wheels and support rollers of rubber or iron.

This catalogue contains a list of our products. Many products are constructed especially for one maschine, and it is therefore possible that the sparepart, you need does not appear in the catalouge, but still can be delivered from our stock.

For further information, please inquire:

H. Andersen A/S Tndervej 186580 Vamdrup

Tel: (+45) 75 58 20 66 Fax: (+45) 75 58 22 02 E-mail: info@h-andersen.dk Homepage: www.h-andersen.dk

Traction belts

3

The traction belts of our sift belts are always of EP1000/3 quality. This means that they are made of three ply, ployester fibres in the warp and ployamid fribres in the weft. The tensile strenght is 1000 kg per cm. of belt width.

The rubber sheets from which the belts are cut have been specially developed and produced for our sieve webs in collaboration with ROULUNDS in Odense, Denmark. The rubber of these belts is of a wear-resistant and weatherproof quality, making them ideal for use ifl harvesters and washing systems for vegetables and fruit. The hardness of the rubber is 65 +/- shore A

Because the belts are profiled and cut later, we are in a position to offer considerable flexibility in terms of standard pitches and belt widths.

Low profile S=Pitch2028323336404244455055

Width (mm)6050, 6050, 60, 756050, 60, 7550, 60, 7550, 60, 756050, 60, 7550, 60, 7560

S

Type S

Traction belts

High profile, double profile

Low profile, double profile

High profile

4

S=Pitch3540434450556064

A (mm)88888, 11111111

Width (mm)6050, 60, 7560, 7560,60, 75606060, 75

S=Pitch3540445055

A (mm)8881111

Width (mm)50, 60, 75606060, 7560

S=Pitch28323640424550

Width (mm)606060606060, 7560

A

SType N (A=8)Type HN (A=11)

Type DN (A=8)Type DHN (A=11)

S

A

8

Type DSS

8

Bars

5

Bars

All standard bars are made of class C spring steel (DIN 17223). Bars with square pitches are made of hardened Borium SB27M12CB Steel. All Bars come either cranked or non-cranked.The cranking can be done to varrious heights. The bars are fastened to the belt with two rivets per belt. The diameter of the rivets is 5 or 6 mm.

Sieve webs

6

Standard sieve webs

Sieve webs are made of two or more traction belts. The bars can be fastened to the central belt in one of two ways:

a) by means of a centre clip (MB) for bar diametres of 9, 10, 11 and 12 mm.

b) by means of a central flattened rod for bar diametres of 9, 10, 11, 12 and 13 mm.

Standard

Sieve belts

7

Special sieve belts

For the processing of small products such as flower bulbs and French carrots, we produce sieve webs fitted with double bars. Combined with the special coverings we can archieve sifting of 2 mm.

For oblong products as carrots, chicory and salsify much use is made of belts with square pitches. These can be made in several sizes, taking intro account the standart pitches. Rod diameter 10, 11 or 12 mm.

Special

Hedgehog webs

Hedgehog webs

8

To separate haulm from the products, hedgehog webs are used. These are avaiable i 3 models:

a) Standard model b) V-profile (not avaiable in every width) c) Cocksomb profile

Joiningmethods

9

1. Chain Lock

Type S: This connection is the fastest and easiest to mount. However, a chain lock is not very strong. the standard joint is made of 3 mm. plate steel.

There are 3 heavier types avaliable.

Type ZL: Welded model with tube of 20 x 10,5, available for all pitches.

Type ZG: Cast steel model (for 60 mm. wide belts and the pitches 36, 40, 42, 45, and 50).

Type ZS: Made of 3 mm. thick hardened steel. The use of hardened steel considerably increases the durability of this joint. The ZS joint consists of 2 equal parts, which has the advantage that the stocks can be reduced.

Chain lock

Type ZS

Type ZL

Type ZG

Type S

Joining methods

10

2. Overlap joint

The advantage of the overlap joint is that the belt can be fitted on the machine quickly and easily. Once in place it offers the advantages of an endless, vulcanised belt.

3. Endless vulcanised belt

An endless vulcanised belt always runs best on the machine. Fitting and endless belt is time-consuming, however, since it is a single unit. The machine must therefore be partially dismantled to fit the belt.

Belts

Bar Covering

11

To reduce siftings and to protect the product, various types of covering are available.

1. Hard Split PylyethyleneThis covering can be fitted to the bars relatively easy. This covering is hard and hence not suitable as protection from damage. Avaliable in the following sizes:

2. Soft Star PVC This covering must be fitted to the bars before they are riveted to the belts. Avaliable in the following sizes:

3. Air Cushion Tube = ACTAvaliable in the following sizes:

6 x 9 11 x 168 x 12 12 x 169 x 12 16 x 20

10 x 14 20 x 2410 x 16

7 1/2 x 14 10 1/2 x 20 8 1/2 x 15 11 1/2 x 18 9 1/2 x 16 11 1/2 x 21 9 1/2 x 18 13 x 19

10 1/2 x 16 15 x 21

11 x 24 15 x 27

Protection from damage

12

To protect the products we have available, in addition to the star PVC and the air cushion tube, various soft profile materials and accessories.

1. Square With air chamber, for 8 mm. squaren steel.

2. Soft vulcanised profileThe hardenss of this profile is 30-35o shore A.

3. Rivet protection This is a type of rubber profile which is slid over the ends of the bars.

Drive wheels

13

Type: S..Z Sprockets for belts with low profile traction belts.These sprockets are cleaveable and therefore easy to fit.

Type: S..M Sprockets with belt support.

Type: MixAlso suitable for driving belts with high profile traction belts.All these sprockets are cleaveable.

Type D TD Min.A Max.AS 28/14M 112 143 25 40S 28/14Z 120 145 25 40S 28/16M 130 167 25 45S 28/16Z 136 163 25 40S 28/22M 179 220 25 50S 28/22Z 187 220 25 50S 32/12M 115 145 25 45S 32/16M 157 185 25 45S 32/18M 175 207 35 60S 36/11Z 120 143 25 40S 36/12M 125 175 25 45S 36/12Z 133 167 25 40S 36/14M 140 190 25 45S 36/16M 170 225 30 45S 36/16Z 170 215 30 45S 36/18M 190 235 30 45S 40/10M 105 150 25 45S 40/14M 160 208 25 50Mix 40/16 197 240 35 60Mix 40/18 225 275 35 55Mix 40/20 254 290 35 50S 42/10M 125 160 25 40S 42/10Z 125 153 25 40S 42/12M 144 204 25 40S 42/14M 175 214 30 50S 42/14Z 184 214 30 50S 42/16M 210 260 25 50S 45/12M 160 202 35 60S 50/8M 105 150 25 40S 50/12M 170 213 25 60Mix 50/14 215 275 40 60S 50/14S 208 260 35 60Mix 50/16 245 298 30 50

A

TDD

Type: S..Z

A

TDD

Type: S..M

ATDD

Type: S..S

ATDD

Type: Mix

Type: S..S

14

Type: N Sprocket for belts with high profile traction belt.All these sprockets are cleaveable and therefore easy to fit.

Type: Mix Also suitable for driving belts with high profile traction belts.All these sprockets are cleaveable.

Type D TD Min.A Max.AN 35/6* 120 180 30 40Mix 35/16 165 216 30 50N 35/17 178 213 30 55N 35/20 212 245 35 65N 40/12* 140 181 25 45N 40/14* 167 215 25 50Mix 40/14* 169 207 35 45N 40/16 192 231 30 45N 80/8 185 211 30 45Mix 40/16 188 231 30 50Mix 40/18 217 263 30 50N 40/18 217 257 35 55Mix 40/20 254 290 35 50N 80/10 254 278 40 45Mix 43/18 235 278 30 60N 44/11* 140 182 30 40Mix 44/16 207 265 35 60Mix 44/20 280 344 35 60N 50/12 177 222 30 45N 50/13 197 232 30 45Mix 50/14 223 275 25 50N 50/16 243 273 30 45Mix 50/16 250 298 30 50*Not cleaveable.

ATD

D

Type: N

ATDD

Type: Mix

Drive wheels

Friction drive

15

It is also possible to drive a sieve web with a low profile traction belt with cage wheels or rubber rollers.

This application requires the tightening of the belt round the drive wheel by means of an extra roller at the drive wheel. -Some are cleaveable

Type D TD Min.A Max.AK80 80 120 20 30K100 100 150 20 30RR100F 100 133 25 50RR110F 110 150 25 50K115 115 166 25 40K140 140 181 25 45RR140F 140 190 25 50K160 160 223 30 4035/17N 178 213 30 55RR180F 180 250 25 50RR240F 240 300 25 60

Rollers

16

Thanks to an excellent arrangement with our suppliers, we have available a wide range of cast iron and rubber rollers.

These rollers are highly suitable for the support and return roller units of our sieve webs.

Under certain circum-stances some of these rollers can also be used as drive rollers.

All rollers can be supplied with an open axle for an M16-bolt or with a shaft. The shafts are made to order, with or without thread.

Rubber bearing racesThese are rubber rollers without a core into which one or more bearings can be pressed.

Type D F LGR60F 60 113 55GR60Z 60 40GR70Z 70 40GR80F 80 130 65GR80Z 80 65GR90F 90 127 80GR90Z 90 60GR100F 100 140 65GR100Z 100 75GR180F 180 228 57

Cast iron rollers

Type D F LRR70F 70 115 60RR70Z 70 40/60RR80F 80 110 70RR80Z 80 60RR90F 90 130 29/60RR90Z 90 32/60RR100F 100 133 60RR100Z 100 70RR110F 110 150 65RR110Z 110 65RR130F 130 190 75RR140F 140 190 75RR180F 180 250 60RR180Z 180 55RR240F 240 300 58

Rubber rollers

Type D LRP64/26 64 26RP82/44 82 44RP82/80 82 80RP82/100 82 100

Rubber bearing races

Shakers

17

The use of shakers fitted under the sieve web increases sifting capacity. These shakers come in the following three models:

Triangular Available in the pitch concerned: 36 42

Rubber This comes in two versions and is suitable for all pitches.

Rubber flights

18

We have a variety of flights available. Our rubber flights are made of top-grade materials with a high wear resistance. They come in the following models:

In principle, these flights are available for all pitches. They are fitted on two bars. To make driving by a sprockets possible a clamp is mounted on the centre of the flight to prevent lateral motion.

Steel flights

19

There are facilities in the welding shop for making steel flights to customer specifications. A few alternatives are reproduced below.

Availability

20

The following is a selection of parts available

Main webs haulm webs hedgehog webs seperating belts crossrunning spike belts sorting belts soil belts elevator belts stone belts chainlocks connecting rods replacement rods and rivets.

Most types of drive wheels, rollers, shaker wheels and special wheels in plain or rubber covered forms.

Various rubber and split hard PVC rod coating rubber plated for haul webs haulm fingers detainers V-belts brushes pendant fingers.

Scrapers lifter shares share bolts.

PTO protectors - call for special brochure.

A large range of parts are available for the following machines:

For enquiries about construction, etc.

please refer to: Product - Type - Year/Model We are always at your sercie with special technical information as well as information about prices and deliveries.See also our website: www.h-andersen.dk

ArmerAsa-LiftBlairDominant Ekengrd Fortschritt Grimme Hagedorn-Wisent Juko

Kverneland Reekie Samro S.P.S. Specialmaskiner Thyregod Tim Underhaug Whlmaus

ContentsH. Andersen A/S Traction belts 3.Low profile/high profile traction belts 4.Bars 5.Standard sieve webs 6.Special sieve webs 7.Hedgehog webs 8.Joining methods 9. -10.Bar covering 11.Protection from damage 12.Drive wheels 13. -14.Friction drive 15.Rollers 16.Shakers 17.Rubber flights 18.Steel flights 19.Availability 20.