Gunjan and Associates - Bank of Baroda...9.Etching to be provide as per Banks Design and...
Transcript of Gunjan and Associates - Bank of Baroda...9.Etching to be provide as per Banks Design and...
S.No. Item Units Qty. Rate Amount
Special Notes-The contractor to visit the banks Vibhuti Khand, Start Up
Model branch before starting the works.
In case of full height partitions measurement of height shall be taken from the finished floor level
upto the level of the false either side of the partition ceiling,in case of varying heights on average
height shall be considered.
The rate to include provision of extra framework as ecessary for skirting & making provision for
9.Etching to be provide as per Banks Design and Specification.
3.The Contractor should strictly follow the Booklet requirements of the Bank
including the detailed drawings in the booklet. Any discripencay between the booklet and the Specificaions below should be brought to the notice of the Architect.
2.No payment shall be made for any in completed or unsatisfactory work
Gunjan and Associates Architects, Engineers, Interiors
& Landscape Designers
141,Sainik Nagar,Raibareli Road, Lucknow-226002
Phone: 0522-2441118, 9839018489, 9838818489
E-mail:[email protected]
URL:www.gunjanandassociates.com
Bill of Quantitiy for Furnishing works for Bank of Baroda
At Branch & E-Lobby at E-Vijaya Jankipuram Branch, Lucknow.
5.Cable Managers to be provided in the tables and Counters wherever required.
BANKS COLOUR SCHEME TO BE FOLLOWED. ANY OTHER COLOUR MENTIONED BELOW TO BE SUPERCEDED BY BANKS COLOUR CODE.
1.No offsite prefabrication shall be allowed in any case. All fabrication shall be done at the site after getting the materials inspected by the architect
4.List of material to be strictly as per the booklet.
6.All underframe should be properly treated with antitermite and waterproofing material
7.All Locks in the drawers and doorsetc. should be of Godrej
8.All keyboard Trays and Drawers to be on Channel Sliding Mechanism.
The rate to include provision of extra framework as ecessary for skirting & making provision for
laying conduit as/drng & directions of site engr./architect.All underframing to be treated with
antitermite solution chlorpyriphos based in recommended dilution.
1 Wooden Partitions (partly glazed/unglazed and Doors) with etching. Sqft. 690.33
Glazed Partition(upto false ceiling height only considered and above necessary ceiling
supports to be provided) with Anodized Aluminium frame work, heavy sections (2mm
thickness) of 2"x1.5" section, spacing of 2'0"x2'0" on bothsides and covered with 9mm
thick BWR plywood finished with 1mm thick laminate of skriting & borders on both
sideswith necessary Pedilite SH adhesive, screws and bolts, etc; & above 8mm thk
float glass with aproved quality and pattern frosted film, as per design Glass panel to be
fixed with 19 X 32.5 mm teakwood beading alround. Glass to be butt jointed and edges to
be ground/machine polished to get a flush joint complete as directed and sealed with
silicone sealent. Framework of partition is to be fixed to RC ceiling for support.All
surfaces shall be treated with antitermite wood preservatives before covering up
complete as per directions and approval.The contractor to visit the banks vibhuti khand
start up branch before starting the works
The job shall also include for provision of laying conduits, switch boxes etc. The erection
of partition shall include for expansion bolts cleats, clamps bolts, nuts, screws, rivets and
other accessories, all complete up to the satisfaction of the Architect.
All door opening shall have rebated teak wood framework (size - 75mm x 50mm, as per
profile) on vertical (2 Nos.) and horizontal (1 No.) sides, with melamine finish and rebate
of 40mm x 12mm, all complete up to the satisfaction of the Architect.
The partition and doors shall have hinges floor springs/sliding arrangement/hydraulic door
closer, mortise locks (Godrej make all), etc. The rate shall include cost of all materials,
labour, T&P, wastages, etc. required for proper completion of work, all complete to the
satisfaction of the Architect.
Partition to have 100 mm high metallic decorative texture laminate (Sliver Colour) band at
skirting on both sides of partition.
2 Low Height Partition . Glass to be etched Sq. ft. 155.93
Same specification as in 1 but P/F half height partition of height 4'-6" with wooden
laminate till 3'-0" and 1'-6" height 12 mm thick glass secured with D brackets including all
hardware necessary with the same specs as above point (1).Unexposed surfaces shall
be treated with antitermite wood preservatives before covering up complete as per
directions and approval.
3 Cash Cabin Partition Sq.Ft. 160.33
(Cash Cabins)
Providing and fixing of Cash Enclosures at height of 5'-0" and length 5'-0'' with with
Anodized Aluminium frame work, heavy sections (2mm thickness) of 2"x1.5" section,
spacing of 2'0"x2'0" on bothsides and covered with 9mm thick BWR plywood finished
with 1mm thick laminate of skriting & borders on both sideswith necessary Pedilite SH
adhesive, screws and bolts, etc; & above 12mm thk float glass with aproved quality
and pattern frosted film, as per design Glass panel to be fixed with 19 X 32.5 mm
Teakwood beading alround. Glass to be butt jointed and edges to be ground/machine
polished to get a flush joint complete as directed and sealed with silicone sealent.All
surfaces shall be treated with antitermite wood preservatives before covering up
complete as per directions and approval.
Partition to have 100 mm high metallic decorative texture laminate(Sliver Colour) band at
skirting on both sides of partition,
4 FRONT PUBLIC COUNTER WITH CORIAN TOP Rft 30.00
Providing and placing in position Banking Counters in straight/curved shapes 750 mm high made
of 19 mm thk. BWR Ply top duly rounded with 6mm thk. flexi ply covering in 750mm wide working
top, finished with 12 mm thk. high density acrylic (Corian/ LG/ Marino) in curved shape and
rest of the structure made from 19mm thk. BWR ply finished with 1.0 mm thk. decorative
textured high gloss laminate in shade as per BOB standards. Rest of the specifications for
drawer units etc. shall be as per main specifications mentioned above but with divisions for
currency as per Bank's instructions. The drawer units shall be provided with autolocking
system (Godrej) for drawers etc. complete as per design/ drawing. Item also includes
providing & fixing 380mm deep transaction counter in counter fabricated out of 19 thk. BWR ply
finished with 1.0mm thick decorative textured laminate upto 1167 mm height as per arch.
drawing. The rate shall include cutting, making view panel opening (1'-0" x 8"), making good the
surface & edge polish and providing 12mm thick toughened glass in the opening (view panel) of
size 1'-0" x 8"with sillicon adhesive etc. complete to the entire satisfaction of Architect/Bank's
Engineer.Space to be left for conduits for lighting of the counter above skirting level.
5 CASH COUNTER WITH CORIAN TOP Rft 10.00
Providing and placing in position Banking Counters in straight/curved shapes 914mm Providing and placing in position Banking Counters in straight/curved shapes 914mm
high made of 19 mm thk. BWR Ply top duly rounded with 6mm thk. flexi ply covering in
750mm wide working top, finished with 12 mm thk. high density acrylic (Corian/
LG/ Marino) in curved shape and rest of the structure made from 19mm thk. BWR
ply finished with 1.0 mm thk. decorative textured high gloss laminate in shade as per
BOB standards. Rest of the specifications for drawer units etc. shall be as per main
specifications mentioned above but with divisions for currency as per Bank's
instructions. The drawer units shall be provided with autolocking system (Godrej)
for drawers etc. complete as per design/ drawing. Item also includes providing &
fixing 380mm deep transaction counter in counter fabricated out of 19 thk. BWR ply
finished with 1.0mm thick decorative textured laminate upto 1200 mm height as per
arch. drawing. The rate shall include cutting, making view panel opening (1'-0" x 8"),
making good the surface & edge polish and providing 12mm thick toughened glass in
the opening (view panel) of size 1'-0" x 8"with sillicon adhesive etc. complete to the
entire satisfaction of Architect/Bank's Engineer.Space to be left for conduits for lighting of
the counter above skirting level.
6 12 MM THICK GLASS FOR CASH CABIN'S AND FRONT COUNTER WITH ETCHED. Sq.Ft. 90.00
Providing and fixing 12mm thk. etched Glass in front portion of Public Counter with metal clamps
including cutouts for passing currency and communication as per details. The edges of the glass to
be polished etc. complete to the satisfaction of Architect/ Bank's Engineer.
7 Wicket Gate Solid No. 1.00
(Banking Hall) SS finish Hinges
Size-3'-0" X 5'-0"
Board-19mm thick (BWR Grade IS303)
(Incl Door Closer/Stopper/mortice lock)
8 Entrance Door Toughened with Toughened Fixed Glazing Sq.Ft. 100.00
Providing and fixing front Frameless Patch Fitting Door with 12mm thick toughened glass with
frame less glass fittings joining 2 glass & double action floor springs
(Hettich/Dorma/Godrej) as per design. The item includes providing and fixing S.S. handle not
less than 600mm long on both side of glass, locks and fittings (Haffle/ Hettich/ Ozone) as per the
manufacturer's specifications etc. complete to the satisfaction of Architect/ Bank's Engineer.
inclusive of P/f Digital Glass Film (3M) for eteching as per design in all shapes including
curve shapes etc. complete to the satisfaction of Architect/Bank's Engineer.
9 Storage (Low Height / Full height Storage/ Overhead ) Sq.Ft. 50.00
P/F in position 450mm deep storage full ht./low ht.cabinets having sides partitions,shelves &
shutters,fabricated out of 19mm BWR & 6mm th.BWR Plywood back,with all exposed
surfaces & inside of shutters/internal base of drawers to be finished with 1mm th laminate of rate
not less than Rs.1300/-Per Sheet & P/F decorative mettalic laminate skirting(silver paint brush
1001 PB of Century)(100mm)as/arch.drg. i/c 31x31mm rounded steem beech wood moulding
& 6x19mm steem beech wood edging on edges of comm.board as/arch.drg.complete
with shelves,shutter,drawers etc.i/c P/F necessary hardware telescopic channels for
drawers of Hettich,S.S.piano hinges as/appvd.sample,Hettich handles(as/appvd.sample)in all
drawers & shutters,locking arrangement,75mm brass tower bolts,Hettich locks in all shutters &
drawers,magnet catcher,painting the exposed internal surfaces of block board with 2-3 coats
of synthetic enamel paint with melamine finish on wood surface with 6mm comm.ply at rear
as per arch.drg.& as per site requirements the rate should include 19mm th.pre-polished
Itallian granite stone (Asian Quartz) of rate not Less than Rs.350/-per sqft.as per appvd.sample
with half round bevelled edge complete on low ht.storage cabinets.
10 Table with 12mm thick glass top
For Branch Manager Tble (Size-6'-0" X 3'-0" X 2'-6") No. 1.00
For Officer Table (Size-4'-9" X 3'-0" X 2'-6") No. 1.00
Providing and placing Table made of 12mm thk. BWR ply finished with approved 12mm thk. corian
solid acrylic surface on table and sides made with 19mm thk. commercial ply finished with
1.0mm thk. high gloss decorative laminate.Modesty panel to be made of 12mm thk. frosted
toughened glass. Table top edges to be approx. 75mm thk. with corian finish as per design &
details. Rest of the specifications for drawer units etc. shall be as per main specifications
mentioned above etc. complete as per design/ drawing.
Table have 19mm thk. BWR ply top and sides and 1.0 mm thk. laminate
(Decorative/Texture/Metallic) finish on exposed surfaces along with 0.8 mm thk. white laminate
on inside surface, drawer units to be made from 12 mm thk. BWR ply with 19mm thk. BWR ply
FASCIA with 1.0 mm thk. decorative texture laminate finish (as per individual item).The drawers to
run on telescopic drawer channels. Drawer units shall have two smaller and one bigger drawer and
auto locking arrangement (Godrej). Footrest 75x50mm made of 2nd class teakwood member
to be fixed in each table. The rate shall include providing all hardware such as drawer channels,
S.S. handles, cable manager (Hettich/ Dorma/Haffele) etc. complete. The item also includes a
tray for keyboard runing on telescopic channel, finshed with decorative texture laminate on top and
rounded front of size 560x450mm, readymade CPU trolly with castors etc. complete to the rounded front of size 560x450mm, readymade CPU trolly with castors etc. complete to the
satisfaction of Architect/ Bank's Engineer.
11
Providing and fixing Side Storage Tables made of 19 mm thk. BWR Ply having 450mm
wide top provided with 12 mm thk. high density acrylic (Corian/ LG/ Marino) and sides
finished with 1mm thk. decorative laminate. The side table to have 2 drawers
on top with shuttered storage below. The inside of side table to be finished with
0.8mm thk. white laminate. The rate shall include providing all hardware such as
auto hinges, S.S. handles (Hettich/ Dorma/Haffele) and locks (Godrej) etc. complete
as per design/drawing to the entire satisfaction of Architect/Bank's Engineer.
i) Size (3'-6"X1'-4"X2'-6") FOR BM CABIN Nos. 1.00
ii) Size (3'-0"X1'-4"X2'-6") FOR S/W COUNTER/FIELD OFFICER TABLE Nos. 1.00
12 CENTRE TABLE/ TEA POY Nos 1.00
Supplying and providing 2'-3" x 2'-3" Tea poy as
follows.
Skeleton of the tepoy shall be made of Steam beach members of 1 1/2" x 1 1/2". Top shall
be made from 12mm thick palin Glass with bevelled and polishing edges shall be
provided. One shelf of 18mm thick MR grade plywood shall be provided at the bottom. All
the surface shall be polilshed as directed.
13Writing Table & Brochure Holder , Cheque Drop Box ,Suggestion Box with Notice
Board .( The work shall be executed as per design and Elevation. ) No. 1.00
Providing and fixing in position a writing counter with open storage made of 12mm and 19mm thick
ply/ commercial board finished with 1.0mm laminate and teak wood moulding/ lipping with a 6mm
glass top with polished edges as per drawing and design. The glass to be of size to fit internally and
the 19mm border and 6mm lipping to be flushed with the glass. The storage unit shall consist of
vertical space dividers of 12 mm board with 1.0 mm laminate till the glass top for the provision of
holding withdrawl/ deposit slips stationery etc. The counters to be held in position around the
columns by dash fastners at a height of 3.5/ 4 ft. Notice board with cellotex base & cloth bound in
corporate coloured binded with teak wood lipping of 35 by 12 mm.size 1500X1200.All wooden
surfaces to be finished in clear melamine polish and all unexposed sides to be finished in enamel
paint of approved colour to be approved by the designer all complete as per detailed drawing,
specification and direction of the Engineer in Charge.
14 ARMSTRONG TILE CEILING Sq.Ft. 500.00
Providing & Fixing of Armstrong Mineral Fibre Acoustical Suspended Ceiling System with Dune
(Bevelled Tegular) Edge Tiles With Armstrong 15mm Exposed GRID. The tiles should have
Humidity Resistance (RH) of 99%, NRC 0.5, Light Reflectance
≥85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0 /
Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 16mm , suitable for Green Building
application, with Recycled content of 32%. The tile shall be laid on Armstrong Silhouette profile grid
system with 15mm white flanges incorporating a 6mm central reveal in white/black colour and with a
web height of 45mm and a load carrying capacity of minimum 15.68 Kgs/M2 & minimum pull out
strength of 100 Kgs..
Silhouette, Main Runners & Cross Tees to have mitred ends & “birdsmouth” notches to provide
mitred cruciform junctions. The T Sections have a Galvanizing of 90 grams per M2 and need to be
installed with Suspension system of Armstrong make. . The Tile & Grid system used together should
carry a 30 year warranty. INSTALLATION: To comprise main runner spaced at 1200mm centres
securely fixed to the structural soffit using Armstrong suspension system (specifications below) at
1200mm maximum centre.
15 False Ceiling Works (Gypsum) Sq.Ft. 800.00
Providing and fixing Gypsum board 12.50 mm thick false ceiling in steps and design using Original
Indian Gypsum board with original company GI sheet section (Gypsteel) supporting system in lline
and level. Finishing the surface and applying 3 coats of flat paint as directed complete entire work to
be done as per
standard specifications of Indian Gypsum. Note : (1) Rate includes making necessary cutouts for
lighting fixtures .. (2) Pattas of Less than 1'-0" shall be
measured in Sqft and not in Rft and paid in Sqft). (3) Only finished surface area shall be measured
for
payment.
16Designer MDF board false ceiling/Pillars 12mm thick with CNC Cutting and backing of
Acryllic /Metalim,Eqivalent as per direction of the architect.The support system to be as
above.
Sq.Ft. 225.00
17 Vertical Blinds Sq.Ft. 85.00
Providing & fixing Sun/Vista make as approved by Bank's Engineer/Architect with runner, thread
and other accessories.
18 Pannelling
a
Wall Panelling-upto false ceiling height only considered and above necessary ceiling supports shall
be provided) with Anodized Aluminium frame work, heavy sections (2mm thickness) of 2"x1.5",
spacing of 2'0"x2'0" on bothsides and covered with 6mm thick BWR plywood finished with 1mm
thick laminate colours for skriting & borders,. Rate to include providing cutouts and provisions to
run electrical conduits, switches, etc.Cost include necessary hardwares like clamps, screws and
etc.Cost include provisions for electrical db closing 19mm BWR plywood door arrangements,
wastages, transports, loading, unloading charges,labours, materials, tools, ead, lift and
etc.Complete as per drawings and instructions of the Architect.Partition to have 100 mm high
metallic decorative texture laminate (Sliver Colour) band at skirting on both sides of partition.
Sq.Ft. 850.00
b
Providing & fixing Panelling (Laminate) with frame work with 45 x 25 mm GI sections (India Gypsum)
@ 600 mm c/c in both directions, finished with 9mm thk. BWR ply. The ply to be covered with
1.0mm thk. decorative texture laminate in two or more colour. Paneling to have 50x35mm teak
wood moulding on edges. Panelling to have 100 mm high teak wood DUCO painted BOB
STANDARD/Teak/Metallic band at skirting including moulding and provision of extra frame work
as necessary for skirting and making cutouts for electrical switch plates, switch boxes, light fittings
light etc. making provision for laying conduits as per drawings & directions etc. complete to the
satisfaction of the Architect /Bank's Engineer.
Sq.Ft. 150.00
19Meter Boxing with proper locking system, 2 nos. of air-con louvers & all necessary
accessoriesSq.Ft. 50.00
Boxing to be done up-to false ceiling
Manufacturing, supplying and fixing box type metre storage with overall depth of 1’6” and
height up-till the false ceiling,. comprising of the following.
19mm block board hinged double shutter, height as size of the panel with alround
beadings 3/4” x ½”, powder coated handles, piano hinges, magnetic ball catches, lock,
locking arrangement, tower bolts etc., all as per directions.
All visible surfaces to be fixed with 1.0mm thick lamination sheet with matching grains &
grooves as per instructions
All internal & rear surfaces to be painted with two coats of enamel paint over a coat of
primer / putty as directed to get a smooth finish.
This would include the fixing of 2 aluminium air-con louvers on both shutters.
20 Acrylic Emulsion with POP Base.(WALL & CEILING) Sq.Ft. 2000.00
Providing & applying the walls, ceiling and elsewhere with Plastic Emulsion Paint
(roller finish) after preparing the base by removing existing paint/ finish and applying 2-3
coats of birla white putty for making the surface plane & smooth and than applying 2 or
more coats of plastic emulsion paint with final coat done with rollers as per
manufacturer's specifications etc. complete to the satisfaction of Architect/Bank's
Engineer. inclusive of Providing and applying approx. 12mm thk. POP Punning on walls ,
ceiling and elsewhere to give a clean smooth and plumb surface as per the instructions of
Architect/Bank's Engineer.
The rate shall include cost of all materials such as plaster of paris, whiting /primer, glue
(Fevicol), indigo / stainer, brushes, sand paper, patti, dhoti, broom stick, clean water with
storage and other containers, labour, scaffolding / ladder charges, cleaning of floors and
other sundries etc., all complete to the satisfaction of the Architect.
21 Shutter Boxing with A.C.P. Sqft 130.00
Frame Work-2" X 2" X 1.5 mm thick Aluminium Tubular section (Horizontal/Vertical) Jindal Make
Aluminium Composite Panel-3.0mm thick of approved colour with bonding material
With trap door
22 VITRIFIED TILES WITH SKIRTING Sqft 1275.00
Existing tile removal and new tile Providing and laying “Doubly Charged” Providing and
laying Vitrified Tile Flooring with glazed finish vitrified tiles of size 600 x 600 mm, laid in
pattern as per design with adhesive from Roff Chemicals or laticrete or approved
equivalent with 3mm joints and providing PVC spacers and joint finished with joint fillers
from Latricrete to match the shade of the tile to the architects satisfaction. The rate to
include laying, curing and covering the floor with PVC sheet and POP and removing and
cleaning after completion as directed. (Marbonite Perlato- 2'-0" x 2'-
0" Basic price of tile Rs. 95/-sft)
23 Flush doors with laminates , 35 mm. thick with T.W frame work NO. 3.00
Supplying and fixing in position overall 32 mm thick solid core hot pressed phenol formaldehyde
bonded approved flush door shutter with T.W./Playwood Frame finished with 4mm thick t.w.
veneer with PU finish/ 1.0 mm thick laminate sheet of approved shade and quality on both
sides of the door shutter including cost of hardware fittings e.g. mortice locks, SS hinges,
door handles etc. of approved
make and quality. (2'-6'' x 7)
24 Powder Coated Sliding Aluminium Windows with Bombay Sliders. Sqft 30.00Supply and Fixing of Aluminum Sliding Windows made from Jindal or equivalent
make Powder Coated (50 micron pure polyester coating ) Aluminum Sections as per detail given
below. –
aMain aluminium tubular section frame of size 4"x1.75"x 16 gauge
minimum weight of section shall be 5.24 kg./15 Rft.
b
Three Track Section frame (3.5’’ x 1.25’’) minimum weight of section should not less
than 4kg/15rft length in 16 Gauge.
cWindow Shutters sections of size 1.6"x0.70” minimum weight of section should not less than 2.60 kg
/ 15 Rft length of section
in 16 gauge.
25 SYNTHETIC ENAMEL PAINT (ON M.S. WORKS) Sqft 450.00
Painting with synthetic enamel paint of approved
brand and manufacture of required colour to give an
even shade :
Two or more coats on new work over an under
coat of suitable shade with ordinary paint of
approved brand and manufacture.
26Dismantling of Existing,Furniture, tiles,platform,demolish and dismantling etc. and
disposl of refuse in desired position complete.Job 1.00
TOTAL BRANCH FURNISHING (A) Rs.
27 False Ceiling Works (Gypsum) Sq.Ft. 900.00
Providing and fixing Gypsum board 12.50 mm thick false ceiling in steps and design using
Original Indian Gypsum board with original company GI sheet section (Gypsteel)
supporting system in lline and level. Finishing the surface and applying 3 coats of flat
paint as directed complete entire work to be done as per
standard specifications of Indian Gypsum. Note : (1) Rate includes making necessary
cutouts for
lighting fixtures .. (2) Pattas of Less than 1'-0" shall be
measured in Sqft and not in Rft and paid in Sqft). (3) Only finished surface area shall be
measured for
payment.
28
Designer MDF board false ceiling with CNC Cutting and backing of Acryllic
/Metalim,Eqivalent as per direction of the architect.The support system to be
as above.
Sq.Ft. 65.00
29 Entrance Door Toughened with Toughened Fixed Glazing. Sq.ft. 90.00
Providing and fixing front Frameless Patch Fitting Door with 12mm thick toughened glass
with frame less glass fittings joining 2 glass & double action floor
springs (Hettich/Dorma/Godrej) as per design. The item includes providing and fixing
S.S. handle not less than 600mm long on both side of glass, locks and fittings (Haffle/
Hettich/ Ozone) as per the manufacturer's specifications etc. complete to the
satisfaction of Architect/ Bank's Engineer. inclusive of P/f Digital Glass Film (3M)
for eteching as per design in all shapes including curve shapes etc. complete
to the satisfaction of Architect/Bank's Engineer.
3012MM THICK FIXED TOUGHENED GLAZING WITH ETCHING ON ENTRANCE
WINDOW OF E-LOBBY Sq.ft. 100.00
E-Lobby
P/f Digital Glass Film (3M) for eteching as per design in all shapes including
curve shapes etc. complete to the satisfaction of Architect/Bank's Engineer. for
interior and exterior signages to be fitted over as per the
pattern / designs wherever required and cut and fitted in
place as per the manufacturer's instructions and to
achieve patterns / designs specified by the bank
31 12 MM THICK TOUGHENED GLASS DIVIDER WITH STEEL CLAMPS sq. ft. 55.00
Providing and fixing 12 mm toughened glass fixed with Steel clamps between
machines.(5'-0''X3'-0'')WITH ROUNDED EDGES.
32 POSTER FRAMES -WALL MOUNTED NO. 2.00
2 sheets of 36'' x 24'' clear acrylic (poster to be sandwiched in between). Outer sheet is
5mm thick and bevelled crystal edge polished for 3/4'' at 8-10 degrees on all sides in the
front.Rear sheet is 5 mm thick flat.
33 Wall Panelling Sq.ft. 220.00
Frame Work-2" X 2" X 1.5 mm thick Aluminium Tubular section (Horizontal/Vertical) Jindal
Make.Aluminium Composite Panel-3.0mm thick of approved colour with bonding
material.Panelling to have metallic decorative texture laminate(Sliver Colour)As per
direction of the architect.
34 Shutter Boxing with A.C.P. Sq.ft. 125.00
Frame Work-2" X 2" X 1.5 mm thick Aluminium Tubular section (Horizontal/Vertical) Jindal
Make
Aluminium Composite Panel-3.0mm thick of approved colour with bonding material
With trap door
TOTAL (B) Rs.
CIVIL WORKS FOR BRANCH & E-LOBBY
Note: 1. All rates of items are including to dismantling works and make it
ready for new works except the dismantling of brick wall in E-Lobby .
2. All concealing/chasing works to be done properly.
3. Tiling work to be done only after the laying down of A.C. drain pipes.
35Demolish and Dismantling of existing wall and rolling shutter E- Lobby area
etc.Job 1.00
Dismantling Existing constructed Brick Wall to be
dismantled manually, mechanically with small machine with proper care to be taken
to make necessary curtain with adjoining plots/ houses so as to protect any
untoward accident, the cost shall include dismantling of the existing structure,
throwing away the dismantled structure to far off place including transportation,
removal of all the debris from the site, and cleaning the site to make it smooth
surface, the cost of dismantlement shall include replastering the surfaces and white
cement putty wherever required. Complete with all materials, labour etc
36
Providing and constructing Brickwork in partitions 230mm thk. with approved quality
well burnt table moulded bricks of minimum crushing strength 50Kgs/Sqcm in CM
1:4 proportion for walls upto 230 mm thickness at all levels and heights including
cost of providing fabricating and placing in position 2 nos of 6mm dia steel bars at
4th course held together by 6mm stirrups at 150 mm c/c. the cost to include all
materials, labour, soaking bricks, staging platform, curing, cost of building in
holdfasts providing holes,including,plastering etc
complete.
CUM 8.00
Reinforced cement concrete work in beams, floors, roofs having slope up to 15°
landings, balconies, shelves, chajjas, lintels,bands, plain window sills, stair cases
and spiral stair cases up to floor five level, excluding the cost of centering,
shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 Cum 2.2037 shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4
graded stone
aggregate 20 mm nominal size). This would include costing of ramp at the entrance
3'-0" wide. beam (9"x9").
Cum 2.20
38
Steel reinforcement bar for R.C.C. work including straightening, cutting,bending,
placing in position and binding all complete Thermo-Mechanically Treated bars ( 10
mm bars) with ringsKg 120.00
39
Casting of the pantry slab and Providing and laying Polished Granite stone flooring
in required design and patterns, in linear as well as curvilinear portions of the
building, all complete as per the architectural drawings, with 18 mm thick stone slab
over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand),
laid and jointed with cement slurry and pointing with white cement slurry admixed
with pigment of matching shade, including rubbing, curing and polishing etc. all
complete as specified and as directed by the Engineer-in-Charge. Polished Granite
stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or
equivalent (GRANITE TO BE APPROVED BY ARCHITECT) size =5' x 1'-6'')
Job 1.00
40Sanitary and water pipelines for the Ladies & Gents Toilets and Pantry.
Nos 3.00
Providing and fixing in position all sanitary and water pipelines including , chase
cutting, cynder filling, water proofing, coat of primer/ anti rust paint at all joints,
proper PVC insulation cover for all pipes. The rates shall include all accessories
like Tees, Unions, elbows,angle volves gate volvs bends,Angular stop
cock,Two way bib cock ,pillar cock ,long body ,Short body Angle valve. Traps
etc required to make the system operational and complete and connected in all
respects to the building's pipelines. This would include connection from the sanitary
fittings and Septic tank/Drain pipe etc. This would include all the concealing work.
No pipe-lines to be exposed.
41 Gents Toilet of the Branch Nos. 1.00
Providing and fixing in a position, western W.C.s wall hung , Half Stall urinal,
automatic cisterns wash basins and all necessary C.P. fIttings and hardware as
per requirement and satisfaction of Bank.
42 Ladies Toilet of the Branch Nos. 1.00
Providing and fixing in a position, western W.C.s wall hung, automatic cistern
wash basins and all necessary C.P. fittings and hardware as per requirement and
satisfaction of Bank.
43 KITCHEN SINK NO. 1.00
Providing and fixing Stainless Steel A ISI 304
(18/8) kitchen sink as per IS : 13983 with C.I.
brackets and stainless steel plug 40 mm,including
of fittings and brackets, cutting and making
good the walls wherever required :Make Nirali or equivalent.Kitchen sink with drain
board
610x510 mm bowl depth 200 mm.
44
Shifting fo the existing rolling shutter & collapsible Channel in new position
and Repair and maintainance of the same including maintenance of the
existing roiling shutter complete in all respects.
Job 1.00
Providing and Fixing in position new roller shutter including boxing at the E-Lobby
entrance complete in all respects with center locking provisions as per the direction
of the architect. (9'-6"x10'-0")Providing and fixing manually operated rolling shutter
of
approved make and type fabricated with 18 gauge section
45
approved make and type fabricated with 18 gauge section
M.S Flats with galvanized pressed steel side guides of one
piece construction including providing the grill in the
middle of rolling shutter of 0.60m high of approved design
and shape pressed steel bottom rail with interlocking
arrangement for steel laths, brackets extra strong door
suspension pipe shaft with high tension coil type spring
made out of spring steel wire, locking arrangement,
holdfast, handles, MS cover hood on top necessary
accessories and fixing with 1:1:5:3 Cement concrete
including painting with synthetic enamel paint three coats
over a coat of primer with putty etc. complete in all
respect
No 2.00
46 SS Railing Front stairs . Sq.Ft. 220.00
providing and fixing brush finish stainless steel (Grade 304) railing made of hollow
tubes, rectangles, channels, plates etc. Including welding, grinding, buffing,
polishing and making curvature (wherever required) and fitting the same with
necessary stainless steel, nuts and bolts complete, i/c fixing the railing with
necessary accessories & stainless steel dash fastners, stainless steel bolts etc. of
required size, on the top of the floor or side of the waist slab with suitable
arrangment as per approval of Architect.
47 Ceramic tiles on Toliets ,Pantry Sq.Ft. 250.00
P/ F Ceramic Tiles on walls and floor and Pantry , 8”x12” Rak Nitco/Kajaria/ Bell/
Johnson make, 1st quality, glazed, of approved shade with white cement incl. 1:4
backing plaster. Basic tile cost Rs.30/sft
48 Casting of folded plate entrance staircase. Job 1.00
casting of r.c.c staircase infornt of branch with the necessary reinforcement
etc.complete in all respects to the satisfaction of the architect and bank.The Flight
width to be 8'-0''.The height of riser not more than 7.25'' and width of tread not less
then 10'' . the job to include plastering etc complete in all respect.
49
Providing & fixing of Granite on Staircase ,ramp
Treads, sill, flooring, etc. complete as per specifications
with 15-18 mm thick mirror polished, machine cut granite with double thick full
round moulded edges
and of required size.The granite treads shall be fitted
with full round moulding shall be fixed with cement grout
on treads and the double thick moulded edge shall be
joined with araldite adhesive to the tread. The cost shall
be inclusive of cutting, moulding, transportation, edge
polishing, etc. complete and also providing two parallel
grooves in the treads as specified.
Sqft 185.00
50 r.c.c ramp
Ramp- providing ramp,for disabled ,in proportion1:1.5:3 [ 1cement: 1.5 aggregate:3
rough finish. This would include plastering etc complete in all respect to the
satisfaction of the architect and bank. JOB 1.00
TOTAL (C) Rs.
GRAND TOTAL AMOUNT (A+B+C) Rs.
Note: All rates are excluding G.S.T.
Ar. Gunjan Kapur
for M/s Gunjan and Associates
BANK OF BARODA
LIST OF MATERIALS OF APPROVED BRAND AND/OR MANUFACTURER
1. The contractor shall use materials in their work subject to inspection, prior to dispatch, by
Owner or his authorized representative of any materials not otherwise specified, shall be in
Accordance with the following list. All materials not otherwise specified shall be in accordance
With the latest Indian Standard Specifications, where such exists with prior approval of
Owner /Architects. The contractor shall be bound to offer sample of materials, which are
claimed to be conforming to I.S Specification, for testing at an approved testing laboratory.
2. Contactor shall purchase all materials from the makers or their authorized stockist only.
Necessary documentary evidences must be produced to the Owner or their authorized
Representative on demand.
3. Contractor shall be bound to supply items or any make of the items as per the choice of
the Owner/ Architects.
A CIVIL / FURNISHING WORK
S.No Description Approved Brand/ Manufacturer
1. Cement M/s ACC, M/sPrism ,M/s Jaypee
2. Wood First class Steam beach wood or as specified
3. Polish MRF Polyurethane
4. Termite treatment Chloroporyphos 20% concentration / Dusban
/Terminator pidlite make
5. Soft Board Celotex
6. Flase Ceiling and Sections Grid Tiles ---Armstrong, St Gobain Gypsum India,
7. Aluminium sections Hindalco, Jindal, Indal
8. Vitrified Floor tiles RAK Asian, Regent, Kazaria, nitco
9. Block boards / Plywood/Flush
doors
M/s Green Panel ( BWR), M/s Century (BWR),M/s Luxe
Design (BWR).
10. Laminates M/s Greenlam, M/s Merino,
M/s Century, M/s AEROLAM M/sArchidlam,
11. Hardware-(Aluminimum) Approved design, brand, quality & manufacture
allowed
12. Hardware ALL HARDWARE TO ONLY GODREJ
13. Drawer/ cabinet
Handless/locks
Dorset / Kitch/ Godrej/ hettich
14. Magnet Catcher Supreme, Excel ,Greenpanl
15. Drawer / cabinet shutter
Accessories
Ebbco, Hettich
16. Synthetic Enamel Paints,
Distemper or Plastic paint
Best quality of make as approved
Asian Paints Ltd), Berger Paints (India) Ltd.(Luxol),
ICI, Nerolac.
17. Venetian blinds/ verticals Vista /Sun
18. Glazing M/s Modiguard, M/s asahi india, Saint Gobain.
19. Door Closer/ floor spring Godrej, Dorma, Ozone
20. Glue Addhessive Fevicole, Century
21. Door handles/ Locks Godrej
22. Screw Excel GKW
23. Glass brass bracket Flora, Perfect
24. POP bag or readymade work Diamond (Super fine quality)
25. GI section for Partitions,
Panel, false ceiling
Same Company as of Gypsum Bard or Mineral Fibre
tiles
26. Film Alkor, Garware, 3M
27. Plants
28. Wire management holes Twinkle
29. Cement Board E board, Bison,
30. Vitrified floor tiles adhesive /
Grout
Bal Endura, Dr. Fixit Fevimate XL with Polymer
Modified Mortar, ROFF Granite tile adhesive
31. Texture Spectrum , Heritage, Acro paint
32. Upholstery Raymonds
33. Sanitary Fixtures Cera, Hindware, Parryware, R.A.K
34. GI Pipes and accessories TATA
35. CI Pipes and accessories NECO
36. Plumbing Fittings Jaquar Continental series
37. Ceramic Tiles Kajaria (High Lighter Concept)
38. Chairs / Sofa Godrej, Delite / Debo