Guerilla TechnologiesFebruary 2011

Information in this document is subject to change without notice. No part of this publication may be reproduced or

transmitted in any form or any means, electronic or mechanical, for any purpose, without the express written permission of Guerilla Technologies. Copyright © 2011

Guerilla Technologies, Inc. All Rights Reserved.

EyeSnap Reader PlusUser Manual

Table of ContentsIntroduction............................................1Shipping Contents..................................2System Layout - Front............................3System Layout - Back............................4Keypad Layout.......................................5What EyeSnap Reader Can Not Read...6Getting Started.......................................7Basic Operating Instructions................12EyeSnap Reader Modes......................18Reading Legal Sized Documents.........20Reading Two Pages of a Book.............21Reading Small Font..............................22Adjusting Reading Speed.....................23Changing Reading Voice.....................24Using Headphones ..............................25Warranty Information............................26Toubleshooting.....................................28

0440014-003 Rev A

IntroductionWelcome to the EyeSnap Reader Plus, the most advanced text to speech reading machine available today.With the EyeSnap Reader Plus, you will experience unmatched speech with TextAloud, powered by AT&T Natural Voices® and world class optical character recognition with ABBYY Fine Reader® software.This Manual and Installation Guide is intended for use by dealers, rehabilitation professionals and users. Note: Guerilla Technologies recommends that EyeSnap Reader Plus be plugged into an uninterruptible power supply (UPS) due to the fact that the computer components are susceptible to power surges, fluctuations and power interruptions during operation.

1440014-003 Rev A

Shipping Contents

You have purchased a complete EyeSnap Reader Plus system, which includes: a Reader, Camera, Keypad, and User Manual.

2440014-003 Rev A

System Layout - Front

3440014-003 Rev A

1. Camera 5. Audio In

2. Headphone Jack 6. Volume Wheel

3. Power Button 7. Speakers

4. USB Ports (2)

System Layout - Back

4440014-003 Rev A

1. Power Plug 7. Camera USB

2. N/A 8. N/A

3. Camera Stand 9. N/A

4. N/A 10. N/A

5. Keypad Plug 11. Speaker Plug

6. N/A

Note: Items labeled “N/A” are not needed for the use of this product.

Keypad Layout

5440014-003 Rev A

1. Start 8. Home2. Pause/Resume 9. Voice Change3. Advance Backward 10. Erase4. Backward 11. Help5. Forward 12. Increase Speed6. Advance Forward 13. Decrease Speed7. Mode 14. Shutdown

Note: Hold the Help Key (labeled 11), then tap any key to have a description of the tapped key spoken.

What EyeSnap Reader Plus Can Not Read

Consistent with all reading machines, EyeSnap Reader Plus cannot read handwritten or hand printed material.

If there is a signature on a typewritten letter, it will read the text but not the signature. If the signature is written over other printed text, the text touched by the signature will not read correctly.

There may be trouble reading some printed forms because a box often surrounds the text on a form. Text that is too close to vertical and/or horizontal lines will possibly be ignored.

6440014-003 Rev A

EyeSnap Reader Plus Set-up

Step 1: Getting Started

1. Plug the power cord into a UPS (uninterrupted power supply)

7440014-003 Rev A

2. Plug the power cord into the power plug on the back of the machine (labeled (1) in the System Layout)

8440014-003 Rev A

3. Plug the keypad plug into the back of the machine. With the flat side of the plug facing up, plug into the bottom, purple PS2 port (labeled (5) in the System Layout)

9440014-003 Rev A

4. Attach the camera stand to the reader. Insert the large screw into the hole on the base connecting the stand to the reader. Tighten the thumb screw to lock into place. Plug the Cameras USB cord into the USB port on the back of the machine (labeled (7) in the system layout overview).

10440014-003 Rev A

5. Turn on EyeSnap Reader Plus with the Power Button on the bottom, front, right corner of the unit (labeled (3) in the System Layout)

11440014-003 Rev A

Basic Operating Instructions

1. Place your reading material (print-side up) on the top of the reader, underneath the camera. A bumper along the back of the machine will provide a guide for proper document placement.

2. Press the Start Key (labeled (1) in the keypad overview). You will hear a camera shutter sound when the image has been captured.

3. After capturing is complete, EyeSnap Reader Plus will automatically begin to read the page aloud.

4. Press the Pause/Resume Key (labeled (2) in the keypad overview) to pause the reading or resume the reading of the current document.

12440014-003 Rev A

5. If desired, you may navigate through the captured document line by line or word by word. First, press the Pause/Resume Key (labeled (2) in the keypad overview) to pause the reading of the current page. (You may do this at any time during the reading of a page.) To skim FORWARD by line, press and HOLD the Forward Key (labeled (5) in the keypad overview) for five seconds. To skim FORWARD by word, TAP the Forward Key. To skim BACKWARD by line, press and HOLD the Backward Key (labeled (4) in the keypad overview) for five seconds. To skim BACKWARD by word, TAP the Backward Key.

Note: As you hold down the key, EyeSnap Reader Plus will move backward or forward by line until

13440014-003 Rev A

the key is released. You will hear a bell chime each time a line has been skipped. This will alert you to how many lines forward or backward you have moved.

6. You may navigate through the stored files on your EyeSnap Reader Plus. Each file is stored by number (file 1, file 2 and so on). To move FORWARD by file, simply press the Advance Forward Key (labeled (6) in the Keypad Layout). To move BACKWARD by file, simply press the Advance Backward Key (labeled (3) in the Keypad Layout).

7. To erase a file on EyeSnap Reader Plus, simply use the Advance Forward or Backward Key to navigate to the file you wish to erase. Once you have reached the

14440014-003 Rev A

desired file to erase, press the Erase Key (labeled (10) in the Keypad Layout Overview). The EyeSnap Reader Plus will say, “Are you sure you want to erase this file? Press the erase key again to erase this file”, press the Erase Key again to confirm the command.

Note: When the EyeSnap Reader Plus has all 20 files filled you will hear a message telling you to please erase one or more files. You will have to erase a file and then capture the document again.

15440014-003 Rev A

8. To adjust the volume on EyeSnap Reader Plus, simply move the Volume Wheel (labeled (6) in the System Layout) to the right to increase the volume. Move the Volume Wheel to the left to decrease the volume.

16440014-003 Rev A

9. To shut down EyeSnap Reader Plus, simply press the Shutdown Key (labeled (14) in the Keypad Layout). EyeSnap Reader Plus will announce, “Thank you for using the EyeSnap Reader. System will shut down in five seconds”, and will then power off.

17440014-003 Rev A

EyeSnap Reader Plus Modes

Column Mode

If you are trying to read a book, newspaper, letter or anything that needs to be read from top to bottom, then Column Mode would be the preferred mode to use.

Tabular Mode

If you are trying to read a bill, spreadsheet or anything that needs to be read line by line, from left to right across the top of the page, then Tabular Mode would be the preferred mode to use.

18440014-003 Rev A

Text File Export Mode

If you would like to export all of the files on the EyeSnap Reader Plus to a memory stick, Text File Export Mode would be the mode to use. Simply press the Mode Key until you reach Text File Export Mode. Insert the memory stick into one of the two USB ports on the front of the machine. Press the Start Key to begin exporting all files on the reader. You will hear a beeping tone as the files are being exported. Once all files are exported the EyeSnap Reader Plus will announce that all files have been exported. Once the export is complete, you may remove the memory stick.

19440014-003 Rev A

Reading a Legal Sized Document (up to 11” x 17”)To read a legal sized document, first, put the EyeSnap Reader Plus into the desired mode using the Mode button on the keypad.

Place the document underneath the camera sideways, going east to west. Then press the Start Key.

20440014-003 Rev A

Reading Two Pages of a BookTo capture and read two pages of a hardcover OR soft cover book, first, put the EyeSnap Reader Plus into the desired mode using the Mode button on the Keypad.

Place the open book underneath the camera, keeping the book as flat as possible. Press the Start Key on the keypad to capture and read the pages.

21440014-003 Rev A

Reading Small Font (less than 7 point)To capture and read exceptionally small font (7 point or less), first, put the EyeSnap Reader Plus into the desired Mode using the Mode button on the Keypad.

Lower the Camera Arm by opening the clamp in the middle of the Camera Arm and sliding the arm down.

Place the text to be read underneath the camera and press the Start Key on the Keypad.

22440014-003 Rev A

Adjusting the Reading SpeedEyeSnap Reader Plus has ten (10) reading speeds.

To DECREASE the reading speed, press the Decrease Speed Key (labeled (13) in the Keypad Layout).

To INCREASE the reading speed, press the Increase Speed Key (labeled (12) in the Keypad Layout)

You will hear, “voice rate up” or “voice rate down”, signifying a reading speed change.

23440014-003 Rev A

Changing the Reading Voice

At any time you may press the Voice Change Key (labeled (9) in the keypad overview) to change the reading voice.

Each time the Voice Change Key is pressed the EyeSnap Reader Plus will say, “Changing voice to AT&T Mike,” then, “Changing voice to AT&T Crystal”. Once a reading voice is selected this will be the default reading voice until the reading voice is changed again.

24440014-003 Rev A

Using Headphones

There are two (2) 1/8 inch jack connectors on the front of EyeSnap Reader Plus. The jack connector on the right is the Headphone Jack Connector (audio out) (labeled (2) in the System Layout). Insert the headphone jack into the Headphone Jack Connector (audio out) on the RIGHT, (labeled (2) in the System Layout).

25440014-003 Rev A

Warranty Information

Guerilla Technology, Inc. warrants that the media the software is recorded on, the product’s documentation and any hardware provided by Guerilla Technologies, are free from defects in materials and workmanship under normal use. Guerilla Technologies warrants that the product will perform substantially in accordance with the specifications set forth in the documentation. Some documents may be processed with a high degree of accuracy. However, poor quality documents, certain typefaces, complex layouts, lower resolutions and poor quality or irregular images may make it difficult or impossible for the product to process pages with satisfactory accuracy. The warranties described above are made for a period of one (1) year from the date the products are delivered to you as the first user.

Guerilla Technologies will repair or replace any hardware, software, documentation or

26440014-003 Rev A

magnetic media that proves defective in materials, workmanship, or must be corrected to achieve warranted performance, without additional charge, on an exchange basis, as described below. If Guerilla Technologies is unable to replace defective hardware, documentation, or defective media, or if Guerilla Technologies is unable to make the product perform to its specifications within a reasonable time, Guerilla Technologies will either replace the entire package with a similar product or refund the purchase price of the product.

Guerilla Technologies does not warrant that the product will meet your requirements or that its operation will be uninterrupted or error free. The warranty does not cover the component or part of the product that has been subjected to damage or abuse, or that has been altered or changed in any way by you or others. Guerilla Technologies is not responsible for problems caused by any user supplied hardware, changes in the operating

27440014-003 Rev A

system, or any upgrades or modifications to these items that are made after the delivery of the Guerilla Technologies product to you. Any implied warranties, including any warranties of merchantability or fitness for a particular purpose, are limited to the term of this express warranty.

Guerilla Technologies shall not, in any case, be liable for special, incidental, consequential, indirect or other similar damages arising from any breach of these warranties even if Guerilla Technologies or its agent has been advised of the possibility of such damages.

Troubleshooting

Question: After pressing the Start Key, EyeSnap Reader Plus does not capture and says nothing.

Possible Solutions:

1. Check the camera’s USB cable. The cable should be securely plugged into

28440014-003 Rev A

one of the USB ports on the back of the machine.

2. Check the Keypad’s connection. The cable should be securely plugged into one of the PS2 ports on the back of the machine.

3. Shut down EyeSnap Reader Plus and check the power cable to make sure it is securely plugged into both an uninterruptable power supply (UPS) and the unit outlet on the back of the machine.

If these solutions do not solve your problems, please contact your dealer or Guerilla Technologies, Inc. for further assistance.

The phone number for Guerilla Technologies technical assistance is:

(772) 283-0500

29440014-003 Rev A