GT16MB Manual P1 P12 - iModel · 14982 4892793149822 gt14b metal gear and pins set 1 1 1 4...
Transcript of GT16MB Manual P1 P12 - iModel · 14982 4892793149822 gt14b metal gear and pins set 1 1 1 4...
R/C Car
Long Nose Pliers
Nippers
Soft Brush Hex Driver
Screwdrive(Small)
Screwdrive(Large)
BatteryCharger Hex Wrench 4 x AA Batteries Wrench
Transmitter
WHAT’S IN THE BOX TOOLS RECOMMENED(NOT INCLUDED)
7.2V 1200mAh NiMHRechargeableBattery Pack
DIMENSIONSCALE : 1/16HEIGHT : 170mmTYRE : ø79mm x 43mm(width)LENGTH : 336mmWIDTH : 239mmWHEELBASE : 189mm
Visit Us on www.carisma.com.hk
Printed in China MAN-G00486
©2013 Carisma. All Rights Reserved. Product specifications are subject to change. Some models shown are prototypes which may vary slightly from what is inside.
2
SAFETY PRECAUTIONS
11
SAFETY PRECAUTIONSTHIS MODEL IS ONLY SUITABLE FOR PEOPLE 14 YEARS OLD AND UP. THIS RADIO CONTROL MODEL IS NOT A TOY.
Introduction
Safety, Precautions, and Warnings
Beginner should seek advice from experienced person in order to assemble the model or parts correctly and to make best performance. * Assemble this model or parts only in place out of children’s reach, and take safe precautions before operating this model. User is fully responsible for the model assembly and safe operations.
This is a sophisticated hobby product and not a toy. It must be operated with caution and common sense. User also requires some basic mechanical abilities. Fail to operate this product in a safe and responsible manner could result in injury or do damage to the product or other properties. This product is not intended for use by children without direct adult supervision. The product manual contains instructions for safe operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual prior to assembly, setup or use, in order to operate correctly and avoid damage or injury.
As the user of this product, you are solely responsible for operating it in a manner that does not endanger yourself and others or result in damage to the product or the property of others.This model is controlled by a radio signal that is subject to interference from many sources outside your control. This interference can cause momentary loss of control so it is necessary to always keep a safe distance in all directions around your model, as this will help to avoid collisions or injury.• Always operate your model in an open area away from cars, traffic, or people.• Avoid operating your model on the street where injury or damage can occur.• Never operate the model out into the street or populated areas for any reason.• Never operate your model with low transmitter batteries.• Carefully follow the directions and warnings for this product and any optional support equipments (chargers, rechargeable battery packs, etc.) that you use.• Keep all chemicals, small parts and anything electrical out of the reach of children.• Moisture causes damage to electronics. Avoid water exposure to all equipments not specifically designed and protected for this purpose.
The associated regulatory agencies of the following countries recognize the noted certifications for this product as authorized for sale and use.
UK
FI
CZ
AT
NL FRDE
EE
SK
IT LU
DK
LV
HUES
MT
BG
LT
RO PT
CY
SE
PL SI IEGR
CE Compliance Information For The European Union
Declaration of Conformity Products: Carisma CTX-2710 2.4GHz Transmitter, MRX2800 ReceiverEquipment Class: 2 The objects of declaration described above are in conformity with the requirements of the specifications listed below.
Manufactured By : Mun Ah Plastic Electronic Toys Company.,Ltd
Statement - This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC ID YDTMTM27HP
Item Name : Carisma CTX-2710 2.4GHz Transmitter and MRX2800 Receiver ETSI EN 300 328 V1.7.1:2006ETSI EN 301 489-1 V1.8.1:2008EN 301 489-17 V2.1.1:2009 EN 50371:2002Directive 1999/5/EC (R&TTE) Article 3.1a Health Article 3.1b EMC Article 3.2 Radio Spectrum
RF Exposure Warning:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.And should be operated with minimum distance of 20 cm between the antenna & your body.
EXPLODED DIAGRAM
Item Name : V6 Type R Electronic Speed ControllerEN 301 489-3 V1.4.1 EN 301 489-1 V1.8.1
Item Name : MS-903GT ServoEN 55 014-1:2006EN 55 014-2:1997 + A1:2001
3
ABOUT THE RADIO SYSTEM
ST.TRIM
TH.TRIM
CTX-2710
Battery Compartment Tray
Steering Trim Dial
Dual Rate Dial
* In general, user will experience under steer when making a wide turn at high speed or over steer when making sharp turn at high speed (easy to spin out). User should practice the throttle and steering approach for different cornering at different speed or road surface.
Battery Installation
SYNC
The following is an overview of the various functions and adjustments found on CTX-2710 radio system for Carisma models. It is important to read and understand about all of these functions and adjustments before driving.
Carisma CTX-2710 2.4GHz FHSS Technology System
Functions
ST.TRIM
TH.TRIM
The Transmitter CTX-2710 Steering Wheel : Control direction (Left / Right) of the RC model. Throttle Trigger : Control speed and direction (Forward/Brake/Backward) of the driving model. Antenna : Transmit signal to the model. Power ON / OFF : Power ON / OFF the transmitter SYNC & Battery Indicator : Top Green LED light indicates synchronization status and/or adequate battery power supply. Power Indicator : Bottom Red LED light indicates power “ON”. Dual Rate Dial : Adjust the same maximum steering angle on both sides when model turns Left / Right ST. Trim Dial : Adjust the neutral position of steering servo when model wheels are straight ahead. TH. Trim Dial : Make sure the model stays still when releasing the throttle trigger. Battery Compartment Tray : Cover and hold the batteries powering the transmitter.
Supplied with 4 x 1.5V AA Batteries, CTX-2710 can be operated a few hours. Installation: Remove the battery compartment cover as shown below.
Install the batteries observing the polarity marked on battery compartment.
Then reinstall the battery compartment cover as the Picture shown below.
Warning : Never disassemble batteries or put the batteries in fire, chemical agents, otherwise they may cause personal injuries or property damages.Battery Disposal : Observe corresponding regulations about wasted battery treatment regulations. 1. After running out of power, dispose of wasted batteries in designated areas far away from water supply, household areas and planted areas.2. Submit the wasted batteries to specific recycling stations.
Battery LED IndicatorThe Green LED indicator located on the front left side of the transmitter indicates the power supply of batteries. The green LED will go solid on indicating that the batteries have sufficient power. When batteries voltage drops below 4 volts, the Green LED will flash, indicating the batteries power is low and should be replaced.
Pre-Run Check
Solid Green : Sufficient Power supply
Flashing : Time to replace batteries
Steering Wheel
Throttle Trigger
Throttle Trim Dial
Antenna
SYNC andBattery
Level Indicator
Power Indicator
PowerON / OFF
Green
Red
SYNC
SYNC Button(Synchronization)
* Always turn on the transmitter first by sliding the switch on the left side from bottom to top. The small red and green lights above the switch should both light up. If not, you need to check for low or incorrectly installed batteries.
1. Steering : Adjust the steering trim to keep the front wheels in straight line when steering wheel remains in NEUTRAL position.
2. Throttle : Adjust the throttle trim to ensure the rear wheels stop rotating when throttle trigger remains in NEUTRAL position.
For Transmitter
Damages or LeakingDo not use any damagedbatteries.
x 4
This product must never be thrown away with other waste. Thus the users are liable for disposingthe wasted model by submitting them to designated collection stations specific for recycling electronic and electric items. Disposing of the wasted model in this way is helpful to conserve natural resources and enable to keep human health and protect the environment. For more information about wasted model disposal and recycling, please contact your local city office, your disposal service or where you purchased the product.
Instructions for Disposal of WEEE by Users in the European Union
Heavy Duty1.5V “AA” Size Batteries
ATTENTION
10
ITEM NO BARCODE PRODUCT NAME PART NO QTYDESCRIPTION
SPARE PARTS LIST
MASM053AMASM1684AMASM1685A
E-RINGFRONT OIL SHOCK SHAFTREAR OIL SHOCK SHAFT
822
SHOCK SHAFT SET489279314805414805
15138 4892793151382 GT16MB VOLKWAGEN BEETLE DESERT EDITON WHEELS & TYRES SET (WHITE) MAT-016-TA-00017BR WHEELS & TYRES SET 2
MAT-016-SA-00017MAT-016-SA-00018
FRONT OIL SHOCK ASSEMBLEDREAR OIL SHOCK ASSEMBLED
22GT14 / 16B / 16MB PLASTIC OIL SHOCK SET489279314922814922
16MBP0302GT14BP0601-01GT14BP0604GT14BP0605
FRONT HING PINFRONT HING PIN BRACEREAR INNER HINGE PIN BRACEREAR OUTER HINGE PIN BRACE
1111
GT16 MONSTER BEETLE HING PIN BRACE SET489279314929714929
14924 4892793149242 GT16 MONSTER BEETLE 370 MOTOR MOUNT 116MBP0401 370 MOTOR MOUNT14926 4892793149266 GT16 MONSTER BEETLE FRONT SHOCK TOWER FRP-G00062 FRONT SHOCK TOWER 1
14928 4892793149280 GT16 MONSTER BEETLE MAIN CHASSIS 1FRP-G00064 MAIN CHASSIS
15140 4892793151405 GT16MB VOLKWAGEN BEETLE DESERT EDITON STICKER SHEET 1DCC-G00289 STICKER SHEET
14927 4892793149273 GT16 MONSTER BEETLE REAR SHOCK TOWER FRP-G00063 REAR SHOCK TOWER 1
112
GT16MBB0101GT16MBB0102MASM1366A
TOP DUST COVERBOTTOM DUST COVERSNAP PIN
GT16 MONSTER BEETLE DUST COVER SET489279314930314930
41212
MASM2158AMASM2156AMASM2157AMASM2155AMASM2160A
BEVEL GEAR 12TBEVEL GEAR 15TBEVEL GEAR 24TBEVEL GEAR 37TPIN
GT14B METAL GEAR AND PINS SET489279314982214982
1114
MAT-016-BA-00013DCC-G00289DCL-G00318MASM090A
GT16MB PAINTED + DECORATED BODYSTICKER SHEETCARISMA LOGO STICKERSNAP PIN
GT16MB VOLKWAGEN BEETLE DESERT EDITONPAINTED + DECORATED BODY489279315139915139
11114
LCB-G00054DCC-G00289DCL-G00969DCL-G00318MASM090A
GT16MB CLEAR BODYSTICKER SHEETGT16MBMASKING SHEETCARISMA LOGO STICKERSNAP PIN
GT16MB VOLKWAGEN BEETLE DESERT EDITON CLEAR BODY SET489279315141215141
21219
MASM033AMASM083AMASM084AMASM270AME031A
BEARING 8x12x3.5mmBEARING 4x7x2.5BEARING 5x9x3mmBEARING 7x11x3mmBEARING 4x8x3mm
GT16MB / GT16MT BEARING SET489279315059015059
GT16MT HARDWARE SET15061 4892793150613
SSW-G00020SSW-G00034SSW-G00035SSW-G00053SSW-G00063SSW-G00066SSW-G00077SSW-G00081SSW-G00088SSW-G00100SSW-G00104SSW-G00144SSW-G00147SSW-G00158SSW-G00175SSW-G00190SSW-G00193SSW-G00228SSW-G00284SSW-G00285SSW-G00331SSW-G00454SSW-G00470SSW-G00659SSW-G00661
SCREW 2.6x10KBSCREW 2.6x12KBSCREW 2.6x12PBSCREW 2.6x6KB SCREW 2.6x6PBSCREW 2.6x6PWBSCREW 2.6x8KB SCREW 2.6x8PBSCREW 2.6x8PWMSCREW 2x6PWB D4.5SCREW 2x10PBSCREW 2x6PBSCREW 2x6KB SCREW 2x8PBSCREW 2.6x10PBSCREW 3x10KMSCREW 3x10PMSCREW 3x18BMSCREW 3x8PB SCREW 3x8PBSCREW M2x8KBSCREW 2.6x10cmSCREW 2x6KMSCREW 1.4x8KB D2.5SCREW 1.4x6KM D2.5
442113481424466485441424142
111111111151544422
GT16BEETLEP0601GT16BEETLEP0303GT16BEETLEP0602GT16BEETLEP0603GT16BEETLEP0604GT16BEETLEP0408GT16BEETLEP0409GT16BEETLEP060516MBP0303GT16BEETLEP0606SSW-G00190GT16BEETLEP0607MASM727ASSW-G00144SSW-G00104SSW-G00077SSW-G00035SSW-G00175
GT16 BEETLE FRONT BUMPERGT16 BEETLE TAIL PIPEGT16 BEETLE EXHAUST PIPE - AGT16 BEETLE EXHAUST PIPE - BGT16 BEETLE REAR BUMPERGT16 BEETLE EXHAUST PIPE MOUNT - LEFTGT16 BEETLE EXHAUST PIPE MOUNT - RIGHTGT16 BEETLE REAR CRASHGUARDGT16 MONSTER BEETLE REAR BUMPER EXTENSIONGT16 BEETLE FRONT BUMPER MOUNTSCREW 3x10KMGT16 BEETLE REAR BUMPER MOUNTM3 NUT (BLACK OXIDE)SCREW 2x6PB BLACK OXIDE (D=3.5)SCREW 2x10PBSCREW 2.6x8KB BLACK OXIDE(D=4.8)SCREW 2.6x12PBSCREW 2.6x10PB BLACK OXIDE (D=4.2)
GT16 MONSTER BEETLE BUMPER SET (UN-PAINTED)489279314919814919
4892793150026 M40B/M40DT LOCKNUT SET15002 M3 LOCKNUTM4 LOCKNUT
64
MASM1168AMASM1011A
4892793150095 CTX-2710 TRANSMITTER15009 CTX-2710 TRANSMITTER ASSEMBLY 1MAT-TXG-MB-00003
4892793152242 BODY CLIP SET (S/M/L)15224BODY CLIP LBODY CLIP MBODY CLIP S
444
MASM1366AMASM032AMASM090A
4892793152211 SET SCREW SET (M3x3 AND #5-40x1/8”)15221 M3 SET SCREW#5-40x1/8 SET SCREW
44
MASM038AMASM969A
4892793152334 FOAM WASHERS SET15233 FOAM WASHERS 4EVA-G00002
4892793148726 GT14 MK3 SLIPPER SPRING AND WASHER SET14872 1.2XID4.2XL5.9X 3.5TURN SLIPPER SPRINGSLIPPER WASHER
12
MASM1758AMASM1961A
4892793149129 GT14B INPUT PINION GEAR SHAFT14912 INPUT PINION GEAR SHAFTSCREW 2X6KM (D=3.5)
11
MASM2080ASSW-G00145
4892793149143 GT14B WHEEL LOCK PIN 1.5X7L14914 PIN 1.5X7L 8MASM245A
4892793149815 GT14B METAL GEAR DIFF SEAL SET14981 SLIPPER 19 x 14.1 x 0.5mm 2 SPC-G00007
4892793150491 GT10DT BALL STUD SET15049BALL STUD4.3 BALL 3.9 BALL
412 2
MASM1632AMASM1803AME017A
4892793150569 GT10DT OUTDRIVE CUP (PAIR)15056 OUTDRIVE CUP 2MASM2159A
4892793151740 GT16MT/ GT16MB / GT10DT DOG BONE SET15174 DOG BONE 4MASM2327A
4892793150460 GT10DT LOCKNUT SET15046LOCKNUT_M4_BLACK ZINCSERVO SAVER ADJUSTORM3.0 FLANGED LOCKNUT
114
MASM1011AMASM2006AMASM733A
4892793149792 GT14B METAL GEAR DIFF SET14979
SCREW 1.4X6KM_D2.5SCREW M1.4X8KB(D=2.5 )SLIPPER 19 x 14.1 x 0.5MMDIFF GEAR ADAPTOROUTDRIVE CUPDIFF GEAR 12TDIFF GEAR 24TDIFF GEAR 15TDIFF GEAR 37TDIFF GEAR 37TDIFF GEAR BOX
24122421121
SSW-G00661SSW-G00659SPC-G00007MASM2160AMASM2159AMASM2158AMASM2157AMASM2156AMASM2155AMASM033AGT14BPROP0701-01
4892793151092 M10DT LOCKNUT SET15109M3 SCREW NUT SCREW NUT M4 LOCKNUT
1225
MASM727AMASM313AMASM1932A
GTBP0201-01GTBP0202-01
ROD BALL CAPGTB ANTI ROLL BAR LINK
62GTB BALL CUP SET489279314939614939
4 9
22
GT14BP0401-02GT14BP0402-02
FRONT ARMSREAR ARMSGT14B SUSPENSION ARMS489279314729314729
11
SLIPPER PLATE ASLIPPER PLATE B
GT14BP0509GT14BP0510GT14B SLIPPER PLATE489279314733014733
111
GT14BP0701-01GT14BP0702-01GT14BP0703-01
SERVO SAVER CAPSERVO SAVER HORNSERVO SAVER ADAPTER
GT14B SERVO SAVER SET489279314736114736
14743 4892793147439 GT14B WHEEL SHAFT (PAIR) MASM1624A WHEEL SHAFT 2
14745 4892793147453 GT14B SLIPPER SHAFT MASM1626A SLIPPER SHAFT 122448
MASM1627AMASM1628AMASM2017AMASM1632AMASM269A
REAR HUB PINFRONT HUB PINARM PINARM PIN BALL HEADE-RING
GT14B HINGE PIN SET489279314746014746
MASM650ASSW-G00595
SERVO SCREW RODTIE ROD
16GT14B TIE ROD489279314755214755
14775 4892793147750 GT14B SPUR GEAR 66T 1GT14BP0704-01 SPUR GEAR 66T
2MASM1625A CENTER DRIVE CUPGT14B CENTER DRIVE CUP489279314744614744
RBP-G00010RBP-G00014RBP-G00012
SHOCK DIAPHRAGMO-RING 2.9x1.78mmO-RING
484
SHOCK O-RING SET14804 4892793148047
SPARE PARTS LISTITEM NO BARCODE PRODUCT NAME PART NO QTYDESCRIPTION
4892793147286 GT14B FRONT AND REAR HUB SET14728
LEFT REAR HUBLEFT SPINDLERIGHT REAR HUBRIGHT SPINDLESPINDLE CARRIER LEFTSPINDLE CARRIER RIGHT
111111
GT14BP0301-01GT14BP0302-01GT14BP0303-01GT14BP0304-01GT14BP0305-01GT14BP0306-01
Top Control Panel
Steering Reverse Switch
Dual Rate Dial
Throttle Reverse Switch
ReversingReversing is used to change the response direction of steering wheel and throttle trigger. CTX-2710 Transmitter features 2 reversing functions: Steering Reverse and Throttle Reverse.Steering Reverse: Reverse the response direction when operating steering wheel. Turning left steering wheel, the model turns right while turning right the model turns left.Throttle Reverse: Reverse the response direction when operating throttle trigger. Pushing forward throttle trigger the model moves backward while pulling back, the model moves forward. If necessary you can just use a small screwdriver to adjust the orresponding switches.
CTX-2710 features two trimming functions:Steering Trim and Throttle Trim.Steering Trim Dial : Adjust the neutral position of steering servo when the wheels are straight ahead. Normally steering trim is adjusted until the model can keep straight tracks.Throttle Trim Dial : Adjust neutral position of throttle servo. Make sure the model stays still when releasing the throttle trigger.
Trimming Dual Rate Dial enables to adjust the same maximum steering angle of servo on both sides (Left and Right) when model makes steering. The Dual Rate Dial affects the sensitivity of servo. Reducing dual rate value can lower the sensitivity of servo and reduce the same maximum steering angle on both sides. Remember to adjust the dual rate value within the adjustment range.
Dual Rate Dial
ST.TRIM
TH.TRIM
SYNC
1. Prior to any operation make sure the transmitter and receiver are both turned off.2. Press and hold the setup button on the receiver while power on the receiver.3. Release the setup button till green LED flashes.4. Press the setup button to select the frame rate with green LED flashing. Faster Flashing = High frame rate (7ms) for digital servo Slower Flashing = Low frame rate (15ms)for analogue servo5. Power on the transmitter. With the transmitter steering wheel and throttle trigger in neutral position (full stop and straight steering), press the SYNC button of the transmitter. 6. When synchronization is done, the green LED on both receiver and transmitter will turn solid on.
Synchronization & Frame Rate Adjust
Setup Key of Receiver
Carisma 2.4GHz Receiver MRX2800
Remarks : The mounting positions of receiver and antenna cable greatly affect the operating range.
Install the antenna vertically to the ground.
Auxiliary Port (Reserved)Steering Port : Where to plug in the servo. Throttle Port : Where to plug in the Electronic Speed Controller (ESC).Setup button : Synchronize transmitter and receiver. Select frame rate.
Steering Port
Throttle Port
Auxiliary Port (Reserved)
Warning : • Never bend the metal pins on the PCB of receiver.• Never cut the antenna cable.• Install the antenna vertically as shown in the figure.• Keep the antenna as far away from the motor, ESC and other noise sources as you possibly can.
Setup Button
Antenna Cable
MRX2800
Tips :• Wrap the receiver with something soft, such as foam rubber, to avoid vibration. If there is a chance of getting wet, put the receiver in a waterproof bag or balloon.
Synchronization Button
ABOUT THE RADIO SYSTEM
RECEIVER CONNECTION AND INSTALLATION
SYNC
Synchronization Button
4892793147309 GT14B BATTERY HOLD DOWN PART/ REAR WING MOUNT14730BATTERY HOLD DOWNREAR WING MOUNT FOR GT14B ONLYBATTERY HOLD POST
224
GT14BP0403-01GT14BP0404-01GT14BP0405-02
112
GT14BP0501GT14BP0505GT14BP0512
CENTER DRAG LINKSTEERING MOUNTSTEERING ARM
GT14B STEERING RACK489279314731614731
111211
GT14BP0503GT14BP0504GT14BP0506GT14BP0508GT14BP0511GT14BP0514
REAR CENTER MOUNTREAR SUPPORTSWAYBAR MOUNT CAP FOR GT14B ONLYWING BUTTON FOR GT14B ONLYANTI ROLL BAR MOUNT R FOR GT14B ONLYANTENNA HOLDER FOR GT14B ONLY
GT14B PLASTIC PARTS SET489279314732314732
1FRP-G00030 UPPER DECKGT14B UPPER DECK489279314750714750
123456789
101112131415
PART NUMBER DESCRIPTION QTYFRP-G00030GT14BP0501GT14BP0505GT14BP0512GT14BP0514GT14BP0603GT16MB VB-002GT16MB VB-002MASM1803AMASM480AMASM481AMASM623ASSW-G00063SSW-G00175SSW-G00331
FRP TOP PLATECENTER DRAG LINKSTEERING MOUNTSTEERING ARMANTENNA HOLDERFRONT SHOCK BRACEMIDDLE TURNBUCKLESERVO TURNBUCKLE4.3 BALL L=10.8KING PIN SHEX LONG KING PIN PRTBUSH2.6x6PB2.6x10PB M2x8KB
111211212226121
1212
4
10
1114
13
5
1
1212 9
158
3
7
2
9
6
11
14
14756
14750
14756
14756
14756
14735
14757
14757
14757
14731
14731
14731
14731
14732
1475715049
15049
10
4
7
UPPER DECK & STEERING POST ASSEMBLY
ASSEMBLEDGT16MB VB-009
15061
1506115061
15061
4892793143530 GT14 BALL STUD SET143534.3 BALL STUD4.3 BALL STUD3.9 BALL STUD
16 4 2
MASM487AMASM615AME017A
4892793146876 GT14B - TELFON SLIPPER PAD14687 SLIPPER SHEET 2SPC-G00005
4892793147347 GT14B - WHEEL HEX14734 WHEEL HEXWHEEL HEX B
42
GT14BP0507GT14BP0516
4892793147354 GT14B - HINGE PIN BRACE /SHOCK TOWER SUPPORT14735
GT16 MONSTER BAJA FRONT HING PIN BRACEFRONT OUTER HINGE PIN BRACEFRONT SHOCK TOWER SUPPORTREAR INNER HINGE PIN BRACEREAR OUTER HINGE PIN BRACEREAR SHOCK TOWER SUPPORTSERVO BRACESHOCK MOUNT SPACE
11111114
GT14BP0601-01GT14BP0602GT14BP0603GT14BP0604GT14BP0605GT14BP0606GT14BP0607GT14BP0515
4892793147408 GT14B - FRONT & REAR DIFFERENTIAL HOUSING14740 DIFF GEAR BOX LOWER HOUSING GEARDIFF GEAR BOX UPPER HOUSING GEAR
22
R14P1101-01R14P1102
4892793147415 GT14B - CENTER DOGBONE SET14741 CENTER DOGBONE (FRONT)CENTER DOGBONE (REAR)
11
MASM1621AMASM1623A
4892793147477 GT14B - STEERING BUSHING14747 STEERING BUSHING 4MASM1631A
4892793147521 GT14B - DIFF OUTDRIVE FOAM STUD14752 DIFF OUTDRIVE FOAM STUD 8EVA-G000034892793147545 GT14B - SERVO SPRING14754 SERVO SPRING �1.0X7.0X10LX4N 1MASM693A
4892793147484 GT14B - BALL DIFFERENTIAL GEAR SET14748
BEARING_8X12X3.5MMBEARING_4X7X2.5MMTHRUST BEARING F2-6(2X6X3)BALL DIFF SPRINGWASHER 8X10X0.2BALL DIFF WASHER3MM BALLDIFF OUTDRIVE FOAM STUDHM2X22 ZINK BLACKADJUST LOCK PART37T RING BEVEL GEAR(BALL DIFF)CENTRE DRIVE BEVEL PINION GEAR 19TBALL DIFF OUTDIVE ABALL DIFF OUTDRIVE B
2 2 1 1 2 210 2 1 1 1 1 1 1
MASM033AMASM083AMASM745AMASM2069AMASM1833AMASM1836AMASM1858AEVA-G00003SSW-G00370R14P0914GT14BP0902GT14BP0907MASM1845AMASM1846A
4892793147569 GT14B - KING PIN SET14756KING PIN SHEX LONG KING PIN
22
MASM480AMASM481A
4892793147576 GT14B - BUSHING14757 BUSHING 6MASM623A
4892793147712 GT14B - PINION GEAR 14T14771 14T PINION GEAR M3x3 SET SCREW
11
MASM671AMASM038A
4892793147989 4500KV BRUSHLESS MOTOR14798 4500KV BRUSHLESS MOTOR 1MOT-G000924892793147996 GT14B - MS903GT SERVO14799 MS903GT SERVO ASSEMBLY 1MAT-SVO-AS-000054892793148016 V6 TYPE R BRUSHLESS ESC14801 V6 TYPE R ASSEMBLY 1MAT-ESC-AS-00002
8 5
BRUSHLESS ESC V6 TYPE R FEATURES
Brus
hles
sM
otor
BrushlessElectronic
Speed ControllerV6 Type R
Power Switch
Battery PlugConnector
Bullet Connector
Setup Button
Steering Port
Throttle Port
Auxiliary Port(Reserved)
2.4GHz ReceiverMRX2800
Servo MS-903GT
• Auto Detect Brushed or Brushless Motor (Details see Select Motor Type)• One Touch End Points calibration• Battery Selection: - 7.4V 2 cells LiPo - 7.2V NiMH• Two ESC profile: - Forward / Reverse with Smart Brake - Forward Only• Battery Over Voltage Protection (Max Input voltage = 13V)• Thermal Protection• Motor Stall Protection
ESC Features:
• After Power On: Just after power on the ESC, the LED will display the currently selected Battery Type for 2 sec: - RED, GREEN LED are used to display Currently Selected Battery Type: RED LED Flashing = LiPo is selected GREEN LED Flashing = NiHM is selected• Battery Type Programming: During the battery type displaying 2 second as mentioned above, user can press the key to select other battery type. Cut-off voltage will be automatically adjusted according to the battery type selected: - For LiPo Battery: ESC will cut-off at 6V - For NiHM: ESC will cut-off at 4.3V
LED Indicator:
• LED Display during “Normal Operation”
ConditionStop GREENPartial Forward OFF
Partial Reverse OFFMax Forward RED
Max Reverse REDBrake RED + GREEN
LED
Step 1 - Turn on the Transmitter, Throttle at Stop position.
Step 2 - Hold the ESC setup key and then power on the ESC.
Step 3 - RED and GREEN LED will turn on, then release the setup key.
Step 4 - GREEN LED flashing, then hold Throttle at Full Throttle position until
GREEN LED become Solid ON.
Step 5 - Then RED LED will flashing.
Step 6 - Next hold Throttle at Max Reverse position until RED LED become
Solid ON.
Step 7 - Release Throttle to Stop position, programming done.
One Touch End-Points Calibration Programming:
LED Display For “Error”• Battery Voltage too high (over 13V) - RED LED solid on and GREEN LED flashing slowly (Can only happen during Power ON).• Overheat - Alternatively Flashing Red and Green• Motor Failure, eg. Motor wire broken, Bad motor, or Motor Jammed - RED LED flashing quickly 3 times, turn off and then repeat• Battery Low - GREEN LED solid on and RED LED flashing slowly
1234567891011121314151617181920
PART NUMBER DESCRIPTION QTY16MBP0301EVA-G00002FRP-G00063GT14BP0507GT14BP0515GT14BP0606GT16BEETLEP0301GT16MB VB-002GT16MB VB-003GT16MB VB-007GT16MB VB-008MASM090AMASM245AMASM313AMASM727ASSW-G00081SSW-G00175SSW-G00285SSW-G00193SSW-G00228
REAR SHOCK TOWER MOUNTEVA WASHERREAR SHOCK TOWERWHEEL HEXSHOCK MOUNT SPACERREAR SHOCK TOWER SUPPORTBODY POSTSREAR TURNBUCKLEREAR OIL SHOCK ASSEMBLYREAR SUSPENSION ARMS ASSEMBLYGEAR DIFFERENTIAL ASSEMBLY SNAP PINPINM3 LOCKNUT BLUE ZING PLATED M3 NUT(BLACK OXIDE)2.6x8PB 2.6x10PB 3x8PB 3x10PM 3x18BM
12122122211422232222
515
3
134
11
19
18
116
145
998
4
1013
6
19
8
7
2
7
18
20
1215
12
17
REAR GEAR BOX & OIL SHOCK ASSEMBLY
BATTERY PACK & CHARGER MANUAL
123456789
PART NUMBER DESCRIPTION QTYGT16MB VB-002GT16MB VB-003GT16MB VB-006GT16MB VB-008EVA-G00002FRP-G00062GT14BP0507GT14BP0511GT14BP0515
FRONT TURNBUCKLEFRONT OIL SHOCK ASSEMBLYFRONT SUSPENSION ARMS ASSEMBLYGEAR DIFFERENTIAL ASSEMBLYEVA WASHERFRONT SHOCK TOWERWHEEL HEXANTI ROLL BAR MOUNT RSHOCK MOUNT SPACER
221121212
10111213141516171819
PART NUMBER DESCRIPTION QTYGT16BEETLEP0301MASM090AMASM245AMASM313AMASM727ASSW-G00081SSW-G00175SSW-G00285SSW-G00193SSW-G00228
BODY POSTSNAP PINPINM3 LOCKNUT BLUE ZINC PLATEDM3 NUT(BLACK OXIDE)2.6x8PB2.6x10PB3x8PB3x10PM3x18BM
2422232222
7
2
1
14
9
10
5
18
2
7
3
10
11
1216
1218
1
6
13 15 174
8
19
11
1234567891011121314
PART NUMBER DESCRIPTION QTYEVA-G00003GT14BP0301-01GT14BP0303-01GT14BP0402-02GT14BP0604GT14BP0605MASM2327AMASM1624AMASM1627AMASM1632AMASM1803AMASM2017AMASM269AME031A
DIFF OUTDRIVE FOAM STUDLEFT REAR HUBRIGHT REAR HUBREAR ARMREAR SUSPENSION INNER BRACE REAR SUSPENSION BRACEDOG BONEWHEEL SHAFTHINGE PIN 27.2mmHINGE PIN BALL4.3 BALL L=10.8SUSPENSION HINGE PINM1.5 E-RING BLACK OXIDE BEARING 4x8x3mm
21121122242244
14
11
21
74
6
141114
8
13
8139
10
1210
1013
54
109
3
12
1
137
14
FRONT GEAR BOX & OIL SHOCK ASSEMBLY
REAR SUSPENSION ARMS ASSEMBLY
ASSEMBLEDGT16MB VB-011
ASSEMBLEDGT16MB VB-007
ASSEMBLEDGT16MB VB-012
15109
15224
15049
15047
15047
15047
15047
1505914743
15174
1472814752
14746
14729 1492915049
15223
15224
1522415109
15109
15019
14927
14735
14735
14735
14734
14914
1473414914
15049
14929
15049 1472915147
1475215049
14728
15059
15059
1474314746
1504914746
14746
15059
14914
15224
15233
14734
14734
14732
14926
14735
15061 15061
15061
15061
15061
Operation• Completely discharge a Nickel - Metal Hydride (NiMH) battery pack before you charge it. Frequent charging a Nickel - Metal Hydride battery pack that is not fully discharged can shorten its battery life.• The battery pack cannot be fully charged when it in low temperate environment.• To charge a very hot after use battery pack can permanently lose its ability to charge.• Unplug the charger from the mains outlet before attempting any maintenance or cleaning.
7.2V 1200mAhNiMH Rechargeable
Battery Pack
7.2V BatteryCharger
WARNINGTo reduce the risk of fire, electric shock or injury, carefully follw these instructions.
This manual contains important safety and operating instructions for your charger. Before using the battery charger, read all the following in this instructions manual on the battery chargers and the rechargeable batteries to be charged, and on the products that use the rechargeable batteries.
Plug supplied charger into mains outlet socket. Connect the 7.2V rechargeable battery pack to the charger. The charger’s connector fits only one way. Don’t force it! If the connectors do not fit together easily, be sure that you have positioned them properly. Average recharging time is approximately 2 to 3 hours maximum. When recharging is over, remove the charger from the household outlet. After recharging is completed, disconnect the battery pack from the battery charger.
The 7.2V battery pack is not supplied pre-charged and you must charge it before connecting the R/C car. The 7.2V battery pack and charger will get hot while charging. This is normal. Do not charge on, or near to, a material / surface that is flammable or can be damaged by heat. When the 7.2V battery pack out of power (dead battery), it should be replaced. Do not dispose in the household garbage but to the collection stations or at a special garbage depot.
CAUTION• The battery charger is not a toy.• Charger only Ni-MH type rechargeable batteries. Other types of batteries may explode and cause serious personally injury or damages.• Never let the charger or battery pack get wet or damp.• Overcharging can damage the battery pack. Follow the indicated recharging time.• Check the batteries regularly for leakage.• Non-rechargeable batteries are not to be recharged.• Do not disassemble the charger. Take it to a qualified service technician when service or repair is required. Improper reassembly may result in a risk of fire, electric shock, or injury to persons.• Do not recharge the battery pack while it is still hot after use. Wait until it has cooled down before recharge.• Use only the recommended batteries or batteries of equal quality.• Do not short circuit - all cables should be insulated. If necessary, use vinyl tape for insulation (NOT INCLUDED).• Do not leave battery pack charger unattended when charging.• The supply terminals are not to be short-circuited.• Packing has to be kept since it contains important information.• Do not expose the charger to rain or excessive moisture.• Do not operate the charger if it has received a sharp blow, or been dropped or damaged in any way. Take it to qualified service technician to repair.• To reduce the risk of damage to the AC plug and cord, disconnect the charger by pulling plug rather than the cord.• Do not use an extension cord. It could result in fire or electric shock.• Do not operate the charge if the cord or plug is damaged. Repair the charger. Never alter the provided AC cord or plug. If does not fit in the AC outlet, have a qualified service technician install the appropriate connector plug. Improper connection can result in an electrical shock. Never use the charger as a DC power source for any other electrical equipments.• Rechargeable battery pack can explode if under incorrectly or non stop charging.• Always observe the polarity to correctly connect : Positive (+) to Positive (+) Negative (-) to Negative (-).
150611506115061
15061
15061
15061
15061
14914
6 7
123456789
PART NUMBER DESCRIPTION QTYGT14BP1001GT14BP1002-01GT14BP1101-01GT14BP1102-01GT14BP1103-01GT14BP1104GT14BP1105-01GT14BP1108GT14BP1110
SHOCK TOP CAPOIL SHOCK BOTTOM CAPREAR SHOCK BODYFRONT SHOCK BODYSPRING CUPSHOCK ENDOIL SHOCK ADJUSTERSHOCK ADJUSTMENT CLIP SET 2mmSHOCK ADJUSTMENT CLIP SET 0.5mm
221122211
101112131415161718
PART NUMBER DESCRIPTION QTYGT14BPROP0101MASM053AMASM1684AMASM1685AMASM2151AMASM204AMASM1736ARBP-G00010RBP-G00014
SHOCK PISTON 1.3mmE-RING ID2.3 BLACK OXIDEFRONT SHOCK SHAFTREAR SHOCK SHAFTREAR DAMPER SPRING5.8 THROUGH BALL(5.79x4.6L)FRONT SHOCK SPRINGSHOCK DIAPHRAMO-RING ID2.9x1.78mm
241114124
65142
78
97
2 16 5
18
123456789
PART NUMBER DESCRIPTION QTY16MBP0302GT14BP0302-01GT14BP0304-01GT14BP0305-01GT14BP0306-01GT14BP0401-02GT14BP0601-01MASM2327AMASM1624A
FRONT SUSPENSION BRACE LEFT SPINDLERIGHT SPINDLESPINDLE CARRIER LEFTSPINDLE CARRIER RIGHTFRONT ARMFRONT SUSPENSION INNER BRACE DOG BONEWHEEL SHAFT
111112122
1011121314151617
PART NUMBER DESCRIPTION QTYMASM1628AMASM1631AMASM1803AMASM2017AMASM269AME031ASSW-G00454EVA-G00003
HINGE PIN 30.2mmSTEERING BUSHING4.3 BALL L=10.8SUSPENSION HINGE PIN M1.5 E-RING BLACK OXIDE BEARING 4x8x3mm2.6x10cmDIFF OUTDRIVE FOAM STUD
24424442
16
12
17
814
13
1
13
78
12
12
15
1116
59
16
15
2
114
15
11
9
66
17
12 12
1014
14
14
10
15
3
16
11
66.
5 ±0
.3
70.
5 ±0
.3
FRONTOIL SHOCK
REAROIL SHOCK
REAROIL SHOCK
FRONTOIL SHOCK
15
156
123456789
101112131415161718192021
PART NUMBER DESCRIPTION QTYSSW-G00661SSW-G00659SSW-G00147SSW-G00063SPC-G00007R14P1102R14P1101-01MASM2160AMASM2159AMASM2158AMASM2157AMASM2155AMASM1803AMASM033AGT14BPROP0701MASM2080AMASM084AMASM1625AMASM038ASSW-G00470MASM2156A
1.4x6KM D2.51.4x8KB D2.5 2x6KB 2.6x6PBGEAR DIFF. SEAL SHEETUPPER DIFF. HOUSING CASE LOWER DIFF. HOUSING CASE PINOUTDRIVE CUPBEVEL PINION 12TBEVEL PINION 24T37T GEAR4.3 BALL L=10.8BEARING 8x12x3.5mmDIFFERENTIAL GEAR BOXINPUT SHAFTBEARING 5x9x3mmCENTER DRIVE CUPM3x3 SCREW2x6KM BEVEL PINION 15T
242211122421221121111
134
4
8
8
9
7
10
11 15
14
3
6
13
10
1
1
11
21
5
16
12
19 17
20
18
14
9
2
2
1234567891011121314151617181920
PART NUMBER DESCRIPTION QTYFRP-G00064GT14BP0403-01GT14BP0405-02GT14BP0502GT14BP0503GT14BP0504GT14BP0607GT16MB VB-004GT16MB VB-005MASM090AMASM671AMOT-G00092SSW-G00053SSW-G00077SSW-G00088SSW-G00147 16MBP0401MASM038AMRX2800DCL-G00233
FRP CHASSIS PLATEBATTERY HOLD DOWNBATTERY HOLD POSTREAR CENTER BEARING BRACE REAR CENTER MOUNTREAR SUPPORTSERVO BRACEMAIN DRIVE SHAFT/SLIPPER UNITSERVOSNAP PINMOTOR GEAR 14T370 BRUSHLESS MOTOR2.6x6KB 2.6x8KB 2.6x8PWM 2x6KB 370 MOTOR MOUNTM3x3 SCREW2.4GHz RECEIVERDOUBLE SIDE STICKER
12411111141174241111
1413
12
7
9
1
10
16
3
1715
8 5 4
2
6
2
318
14
13
13
10
11
3
2019
MAIN CHASSIS ASSEMBLY
FRONT SUSPENSION ARMS ASSEMBLY
DIFFERENTIAL GEAR BOX ASSEMBLY
FRONT AND REAR OIL SHOCK ASSEMBLY
3
4
13
12
11
10
10
17
17
115
1
15
12345
PART NUMBER DESCRIPTION QTYGT14BP0807-01GTBP0201-01MASM650AME017ASSW-G00595
BALL CAPROD BALL CAPM2xL20mm3.9 BALLTURNBUCKLE (M3x38mm)
26123
1234567
PART NUMBER DESCRIPTION QTYGT14BP0509GT14BP0510GT14BP0704-01MASM038AMASM083AMASM1011AMASM1625A
SLIPPER PLATE ASLIPPER PLATE BSPUR GEAR 66TM3x3 SCREWBEARING 4x7x2.5mmLOCKNUT M4 BLACK ZING CENTER DRIVE CUP
1112112
891011121314
PART NUMBER DESCRIPTION QTYMASM1626AMASM1961AMASM270AMASM716AME014AME031ASPC-G00005
SLIPPER SHAFTSLIPPER WASHERBEARING 7x11x3mmSPRING WASHERPIN 1.5x6.0LBEARING 4x8x3mmSLIPPER SHEET
1211212
7
411
6
2
3141
8
4
7
12
513
14 10
9
23.2
±0.2
24±0
.2
11.7
±0.123
.2±0
.2
2
5 14755
1473914739
2 14739
14739
14755
14353
14736
15061
14754 14736 14736
15059 1505915221
1477414745
14733 1468714775
14687 14733 15059
14696
15002 14744
15221 1492214922
14922 1492214922
14922
15056
15049
15049
14740
1498214982
14982
14982
14982
14740
14979
15059
15056
14982
15221
14744
15059
1498114982
1491214982
15059
14922 1492214922
1492214922
149221492214922149221492214922
14922149221492214922
1492214922
14922 14922
149221492214922
1473214732
14730
14730
14730
14924
1477114771 14730
14732
15224
15049
1505914728
1474714743
14728
14746
14746
14929
14746
14729
1492914728
15049
1474315049
1475214747
15059
14728 14747
15059
14729 14746
1475215059
1504914747
15174
15174
15047
15047
15047
1504714928
14799
14735
15224
14798
14799
14739
147555 5
2
147392
1
3
4
1
324
1
6
5
123456
PART NUMBER DESCRIPTION QTYGT14BP0701-01GT14BP0702-01GT14BP0703-01MASM693AMS-903GTSSW-G00284
SERVO SAVER CAPSERVO SAVER HORNSERVO SAVER ADAPTER(JR)SERVO SPRINGSERVO3x8 PB
111111
TURNBUCKLE ASSEMBLY
MAIN DRIVE SHAFT/SLIPPER UNIT ASSEMBLY
SERVO SAVER EXPLODED DIAGRAM
ASSEMBLED GT16MB VB-013
ASSEMBLEDGT16MB VB-004
ASSEMBLEDGT16MB VB-005
ASSEMBLEDGT16MB VB-013
ASSEMBLEDGT16MB VB-008
ASSEMBLEDGT16MB VB-006
Front Turnbuckle
MiddleTurnbuckle
RearTurnbuckle
ServoTurnbuckle
14730
15061
15061
15061
15061
15061
15061
1506115061
15061
15061
15061
15061
15061
15061
15061
1506115061
15061