8/10/2019 GSM Timing advance and Cell re selection

1/15

Timing Advances

Access Burst Duration of a Bit Propagation Delay Max Cell Size Determining a TA Distanceof a TA

Home

`

Introduction

A Timing Advance (TA) is used to compensate for the propagation delay as the signal travels between theMobile Station (MS) and Base Transceiver Station (BTS). The Base Station System (BSS) assigns the TAto the MS based on how far away it perceives the MS to be. Determination of the TA is a normally afunction of the Base Station Controller (BSC), bit this function can be handled anywhere in the BSS,

depending on the manufacturer.

Time Division Multiple Access (TDMA) requires precise timing of both the MS and BTS systems. Whena MS wants to gain access to the network, it sends an access burst on the RACH. The further away theMS is from the BTS, the longer it will take the access burst to arrive at the BTS, due to propagation delay.

Eventually there comes a certain point where the access burst would arrive so late that it would occuroutside its designated timeslot and would interfere with the next time slot.

Access Burst

As you recall from theTDMA Tutorial,an access burst has 68.25 guard bits at the end of it.

This guard time is to compensate for propagation delay due to the unknown distance of the MS from theBTS. It allows an access burst to arrive up to 68.25 bits later than it is supposed to without interfering

with the next time slot.

http://gsmfordummies.com/timing/timing.shtml#access_bursthttp://gsmfordummies.com/timing/timing.shtml#access_bursthttp://gsmfordummies.com/timing/timing.shtml#bit_durationhttp://gsmfordummies.com/timing/timing.shtml#bit_durationhttp://gsmfordummies.com/timing/timing.shtml#delayhttp://gsmfordummies.com/timing/timing.shtml#delayhttp://gsmfordummies.com/timing/timing.shtml#cell_sizehttp://gsmfordummies.com/timing/timing.shtml#cell_sizehttp://gsmfordummies.com/timing/timing.shtml#determine_tahttp://gsmfordummies.com/timing/timing.shtml#determine_tahttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://www.gsmfordummies.com/index.htmlhttp://www.gsmfordummies.com/index.htmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://www.gsmfordummies.com/index.htmlhttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://gsmfordummies.com/timing/timing.shtml#determine_tahttp://gsmfordummies.com/timing/timing.shtml#cell_sizehttp://gsmfordummies.com/timing/timing.shtml#delayhttp://gsmfordummies.com/timing/timing.shtml#bit_durationhttp://gsmfordummies.com/timing/timing.shtml#access_burst

8/10/2019 GSM Timing advance and Cell re selection

2/15

68.25 bits doesnt mean much to us in the sense of time, so we must convert 68.25 bits into a frame of

time. To do this, it is necessary to calculate the duration of a single bit, the duration is the amount of timeit would take to transmit a single bit.

[Back to Top]

Duration of a Single Bit

As you recall, GSM uses Gaussian Minimum Shift Keying (GMSK) as its modulation method, which has

a data throughput of 270.833 kilobits/second (kb/s).

Calculate duration of a bit.

Description Formula Result

Convert kilobits to bits 270.833 kb 1000 270,833 bits

Calculate seconds per bit 1 sec 270,833 bits .00000369 seconds

Convert seconds to microseconds .00000369 sec 1,000,000 3.69 s

So now we know that it takes 3.69s to transmit a single bit.

[Back to Top]

Propagation Delay

http://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#top

8/10/2019 GSM Timing advance and Cell re selection

3/15

Now, if an access burst has a guard period of 68.25 bits this results in a maximum delay time ofapproximately 252s (3.69s 68.25 bits). This means that a signal from the MS could arrive up to

252s after it is expected and it would not interfere with the next time slot.

The next step is to calculate how far away a mobile station would have to be for a radio wave to take252s to arrive at the BTS, this would be the theoretical maximum distance that a MS could transmit andstill arrive within the correct time slot.

Using the speed of light, we can calculate the distance that a radio wave would travel in a given time

frame. The speed of light (c) is 300,000 km/s.Description Formula Result

Convert km to m 300,000km 1000 300,000,000m

Convert m/s to m/s 300,000,000 1,000,000 300 m/s

Calculate distance for 252s 300 m/s 252s 75600m

Convert m to km 75,600m 1000 75.6km

So, we can determine that a MS could theoretically be up to 75.6km away from a BTS when it transmitsits access burst and still not interfere with the next time slot.

However, we must take into account that the MS synchronizes with the signal it receives from the BTS.

We must account for the time it takes for the synchronization signal to travel from the BTS to the MS.When the MS receives the synchronization signal from the BTS, it has no way of determining how faraway it is from the BTS. So, when the MS receives the syncronization signal on the SCH, it synchronizes

its time with the timing of the system. However, by the time the signal arrives at the MS, the timing of theBTS has already progressed some. Therefore, the timing of the MS will now be behind the timing of the

BTS for an amount of time equal to the travel time from the BTS to the MS.

8/10/2019 GSM Timing advance and Cell re selection

4/15

For example, if a MS were exactly 75.6km away from the BTS, then it would take 252s for the signal totravel from the BTS to the MS.

The MS would then synchronize with this timing and send its access burst on the RACH. It would take252s for this signal to return to the BTS. The total round trip time would be 504s. So, by the time thesignal from the MS arrives at the BTS, it will be 504s behind the timing of the BTS. 504s equals about

136.5 bits.

The 68.25 bits of guard time would absorb some of the delay of 136.5 bits, but the access burst would stillcut into the next time slot a whopping 68.25bits.

8/10/2019 GSM Timing advance and Cell re selection

5/15

[Back to Top]

Maximum Size of a Cell

In order to compensate for the two-way trip of the radio link, we must divide the maximum delay distancein half. So, dividing 75.6km in half, we get approximately 37.8 km. If a MS is further out than 37.8kmand transmits an access burst it will most likely interfere with the following time slot. Any distance less

than 37.8km and the access burst should arrive within the guard time allowed for an access burst and itwill not interfere with the next time slot.

In GSM, the maximum distance of a cell is standardized at 35km. This is due mainly to the number oftiming advances allowed in GSM, which is explained below.

[Back to Top]

How a BSS Determines a Timing Advance

In order to determine the propagation delay between the MS and the BSS, the BSS uses the

synchronization sequence within an access burst. The BSS examines the synchronization sequence andsees how long it arrived after the time that it expected it to arrive. As we learned from above, the duration

of a single bit is approximately 3.69s. So, if the BSS sees that the synchronization is late by a single bit,then it knows that the propagation delay is 3.69s. This is how the BSS knows which TA to send to the

MS.

http://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#top

8/10/2019 GSM Timing advance and Cell re selection

6/15

For each 3.69s of propagation delay, the TA will be incremented by 1. If the delay is less than 3.69s,

no adjustment is used and this is known as TA0. For every TA, the MS will start its transmission 3.69s(or one bit) early. Each TA really corresponds to a range of propagation delay. Each TA is essentially

equal to a 1-bit delay detected in the synchronization sequence.

TA From To

0 0s 3.69s

1 3.69s 7.38s

2 7.38s 11.07s

3 11.07s 14.76s

... ... ...

63 232.47s 236.16s

[Back to Top]

The Distance of a Timing Advance

When calculating the distances involved for each TA, we must remember that the total propagation delay

accounts for a two-way trip of the radio wave. The first leg is the synchronization signal traveling fromthe BTS to the MS, and the second leg is the access burst traveling from the MS to the BTS. If we want toknow the true distance of the MS from the BTS, we must divide the total propagation delay in half.

For example, if the BSS determines the total propagation delay to be 3.69s, we can determine thedistance of the MS from the BTS.

Description Formula Result

http://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#tophttp://gsmfordummies.com/timing/timing.shtml#top

8/10/2019 GSM Timing advance and Cell re selection

7/15

Determine one-way propagation time 3.69s 2 1.845s

Calculate distance

(using speed of light.)300 m/s 1.845s 553.5m

We determined earlier that for each propagation delay of 3.69s the TA is inceremented by one. We just

learned that a propagation delay of 3.69s equals a one-way distance of 553.5 meters. So, we see thateach TA is equal to a distance of 553.5 meters from the tower. Starting from the BTS (0 meters) a new

TA will start every 553.5m.

TA Ring Start End

0 0 553.5m1 553.5m 1107m

2 1107m 1660.5m

3 1660.5m 2214m

... ... ...

63 34.87km 35.42km

8/10/2019 GSM Timing advance and Cell re selection

8/15

The TA becomes very important when the MS switches over to using a normal burst in order to transmitdata. The normal burst does not have the 68.25 bits of guard time. The normal burst only has 8.25 bits ofguard time, so the MS must transmit with more precise timing. With a guard time of 8.25 bits, the normal

burst can only be received up to 30.44s late and not interfere with the next time slot. Because of the two-

way trip of the radio signal, if the MS transmits more than 15.22s after it is supposed to then it willinterfere with the next time slot.

Access Burst Duration of a Bit Propagation Delay Max Cell Size Determining a TA Distance

of a TA

Introduction Architecture TDMA Logical Channels Authentication & Encryption Timing

Advances Speech Encoding GSM Events Cell Selection/ReselectionUpdates Sitemap Contact Me

Home

http://gsmfordummies.com/timing/timing.shtml#access_bursthttp://gsmfordummies.com/timing/timing.shtml#access_bursthttp://gsmfordummies.com/timing/timing.shtml#bit_durationhttp://gsmfordummies.com/timing/timing.shtml#bit_durationhttp://gsmfordummies.com/timing/timing.shtml#delayhttp://gsmfordummies.com/timing/timing.shtml#delayhttp://gsmfordummies.com/timing/timing.shtml#cell_sizehttp://gsmfordummies.com/timing/timing.shtml#cell_sizehttp://gsmfordummies.com/timing/timing.shtml#determine_tahttp://gsmfordummies.com/timing/timing.shtml#determine_tahttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://gsmfordummies.com/intro/intro.shtmlhttp://gsmfordummies.com/intro/intro.shtmlhttp://gsmfordummies.com/architecture/arch.shtmlhttp://gsmfordummies.com/architecture/arch.shtmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://gsmfordummies.com/tdma/logical.shtmlhttp://gsmfordummies.com/tdma/logical.shtmlhttp://gsmfordummies.com/encryption/encryption.shtmlhttp://gsmfordummies.com/encryption/encryption.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/encoding/encoding.shtmlhttp://gsmfordummies.com/encoding/encoding.shtmlhttp://gsmfordummies.com/gsmevents/events.shtmlhttp://gsmfordummies.com/gsmevents/events.shtmlhttp://gsmfordummies.com/air/radiolink.shtmlhttp://gsmfordummies.com/air/radiolink.shtmlhttp://gsmfordummies.com/updates.shtmlhttp://gsmfordummies.com/updates.shtmlhttp://gsmfordummies.com/sitemap.shtmlhttp://gsmfordummies.com/sitemap.shtmlhttp://gsmfordummies.com/contact/contact.shtmlhttp://gsmfordummies.com/contact/contact.shtmlhttp://www.gsmfordummies.com/index.htmlhttp://www.gsmfordummies.com/index.htmlhttp://www.gsmfordummies.com/index.htmlhttp://gsmfordummies.com/contact/contact.shtmlhttp://gsmfordummies.com/sitemap.shtmlhttp://gsmfordummies.com/updates.shtmlhttp://gsmfordummies.com/air/radiolink.shtmlhttp://gsmfordummies.com/gsmevents/events.shtmlhttp://gsmfordummies.com/encoding/encoding.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/encryption/encryption.shtmlhttp://gsmfordummies.com/tdma/logical.shtmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://gsmfordummies.com/architecture/arch.shtmlhttp://gsmfordummies.com/intro/intro.shtmlhttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://gsmfordummies.com/timing/timing.shtml#ta_distancehttp://gsmfordummies.com/timing/timing.shtml#determine_tahttp://gsmfordummies.com/timing/timing.shtml#cell_sizehttp://gsmfordummies.com/timing/timing.shtml#delayhttp://gsmfordummies.com/timing/timing.shtml#bit_durationhttp://gsmfordummies.com/timing/timing.shtml#access_burst

8/10/2019 GSM Timing advance and Cell re selection

9/15

Cell Selection and Reselection

Signal Strength RXQUAL Cell Selection and Reselection C1 C2 Cell Reselection Offset Cell

Reselection Hysteresis Cell Bar Access Cell Bar Qualifier

Home

Note: This tutorial is intended for people that have a good basic understanding of GSM fundamentals. It

may be necessary to review Introduction to GSM and Network Architecture before reading this tutorial.

There are many factors involved in maintaining the radio link (Um interface) between the Mobile Station(MS)and theBase Transceiver Station (BTS).As the MS moves throughout the network the signal

strength of the BTS will increase and decrease and the MS will have to continuously monitor the signalstrengths of nearby towers and update which BTS's it camps on. This page covers all of the parameters

that the MS and network will use in order to ensure the the MS chooses the strongest tower to monitorand other network considerations.

Signal Strength

The first and arguably most important consideration in radio link management is signal strength. In GSM

(and most other RF communications) the standard measure of signal strength is dBm (decibelsinmilliwatts). The term received signal strength indicator(RSSI) is often used but in GSM theterm received-signal level(RXLEV) is preferred. The distinction is that the term RSSI was generally usedon analog networks and RXLEV is used on digital networks. On this website RSSI will be used for

general reference to signal strength and RXLEV for the actual value that is passed over the network.

RXLEV

RXLEV is a number from 0 to 63 that corresponds to a dBm value range. 0 represents the weakest signaland 63 the strongest.

http://gsmfordummies.com/air/radiolink.shtml#sighttp://gsmfordummies.com/air/radiolink.shtml#sighttp://gsmfordummies.com/air/radiolink.shtml#rxqualhttp://gsmfordummies.com/air/radiolink.shtml#rxqualhttp://gsmfordummies.com/air/radiolink.shtml#selrelhttp://gsmfordummies.com/air/radiolink.shtml#selrelhttp://gsmfordummies.com/air/radiolink.shtml#c1http://gsmfordummies.com/air/radiolink.shtml#c1http://gsmfordummies.com/air/radiolink.shtml#c2http://gsmfordummies.com/air/radiolink.shtml#c2http://gsmfordummies.com/air/radiolink.shtml#crohttp://gsmfordummies.com/air/radiolink.shtml#crohttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#cbahttp://gsmfordummies.com/air/radiolink.shtml#cbahttp://gsmfordummies.com/air/radiolink.shtml#cbqhttp://gsmfordummies.com/air/radiolink.shtml#cbqhttp://www.gsmfordummies.com/index.htmlhttp://www.gsmfordummies.com/index.htmlhttp://gsmfordummies.com/architecture/arch.shtml#mshttp://gsmfordummies.com/architecture/arch.shtml#mshttp://gsmfordummies.com/architecture/arch.shtml#mshttp://gsmfordummies.com/architecture/arch.shtml#mshttp://gsmfordummies.com/architecture/arch.shtml#btshttp://gsmfordummies.com/architecture/arch.shtml#btshttp://gsmfordummies.com/architecture/arch.shtml#btshttp://gsmfordummies.com/air/decibels.shtmlhttp://gsmfordummies.com/air/decibels.shtmlhttp://gsmfordummies.com/air/decibels.shtmlhttp://gsmfordummies.com/air/decibels.shtmlhttp://gsmfordummies.com/architecture/arch.shtml#btshttp://gsmfordummies.com/architecture/arch.shtml#mshttp://gsmfordummies.com/architecture/arch.shtml#mshttp://www.gsmfordummies.com/index.htmlhttp://gsmfordummies.com/air/radiolink.shtml#cbqhttp://gsmfordummies.com/air/radiolink.shtml#cbahttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#crohttp://gsmfordummies.com/air/radiolink.shtml#c2http://gsmfordummies.com/air/radiolink.shtml#c1http://gsmfordummies.com/air/radiolink.shtml#selrelhttp://gsmfordummies.com/air/radiolink.shtml#rxqualhttp://gsmfordummies.com/air/radiolink.shtml#sig

8/10/2019 GSM Timing advance and Cell re selection

10/15

RSSI below -110 dBm are generally considered unreadable in GSM. RSSI in the area of -50 dBm arerarely seen and would indicate that the MS is right next to the BTS. The main factor that affects RSSI isdistance from the tower. However, other factors such as terrain, elevation, and large objects such as

buildings can dampen signal strength.

RXQUAL

Although a strong RSSI is desirable, it does not guarantee a quality signal. RXQUAL is a value that

represents the quality of the received signal. The MS determines the Bit Error Rate (BER) of the signaland reports it back to the network. The BER is simply a percentage of the number of bits it receives thatdid not pass error checking. The bits may have been garbled along the RF path or lost due to fading orinterference. The higher the BER the lower the signal quality. RXQUAL is given as a number from 0 to 7

and represents a percentage range of BER.

8/10/2019 GSM Timing advance and Cell re selection

11/15

Cell Selection and Reselection

Cell selection refers to the initialregistration that a MS will make with a network. This normally onlyoccurs when the phone powers up or when the MS roams from one network to another.

Cell reselection refers to the process of a MS choosing a new cell to monitor once it has already registered

and is camped on a cell. It is important to distinguish that selection and reselection are done by the MSitself and not governed by the network. The network would only be responsible for this function when theMS is in aTraffic Channel (TCH).When the MS reselects a new cell it will not inform the network that it

has done so unless that new cell is in a newLocation Area (LA).

There are many parameters involved in selection and reselection of a new cell. The MS must ensure it isgetting the best signal and the network must ensure that the MS does not cause unneeded strain on the

network by switching cells when unnecessary or undesired.

C1

C1 is the path-loss parameter that is used to determine the strongest cell forselection. The MS willcalculate a C1 for each tower it can see and select the cell tower with the highest C1. The C1 uses the

following parameters for calculation:

The formula for calculating C1 is given as:C1 = (A) - Max(B,0)

where:

A = (RXLEV - RLAM)B = MS Transmit Power Max CCH -Max RF Output of MS

At first this may seem complicated but if we examine the various parameters and how they affect the C1

score then it becomes more clear.

A - This value is merely a dB value for the difference between what RSSI is required to select that celland what signal strength the MS sees the tower at. If the RLAM is -110dB and the MS sees the tower at -

http://gsmfordummies.com/tdma/logical.shtml#traffic_channelshttp://gsmfordummies.com/tdma/logical.shtml#traffic_channelshttp://gsmfordummies.com/tdma/logical.shtml#traffic_channelshttp://gsmfordummies.com/architecture/arch.shtml#vlrhttp://gsmfordummies.com/architecture/arch.shtml#vlrhttp://gsmfordummies.com/architecture/arch.shtml#vlrhttp://gsmfordummies.com/architecture/arch.shtml#vlrhttp://gsmfordummies.com/tdma/logical.shtml#traffic_channels

8/10/2019 GSM Timing advance and Cell re selection

12/15

8/10/2019 GSM Timing advance and Cell re selection

13/15

The C2 is calculated using the following parameters:

The formula for calculating C2 is:

C2 = C1 + CRO - (Temp_Offset * H)

H = 1 if the MS has been monitoring a particular cell for less than thepenalty time.H = 0 if the MS has been monitoring the particular cell for longer than the penalty time.

H = 0 if the particular cell is the serving cell (the one the MS is currently camped on).

Let's look at an example to see how the temporary offset works. The following chart shows two examplecell towers and values for C1 and C2 parameters. The time progresses as the MS moves away from cell A

and towards cell B. For sake of simplicity, we are assuming that the MS can transmit at the max powerallowed and that neither cell is using CRO.

0 seconds - The MS is camped on cell A. The MS calculates the C2 value as 38. Since the RXLEV forcell B is not above the RLAM the C1 (and C2) are below 0. A MS will not select a cell with a C1 below 0

and it will not reselect a cell with a C2 below 0.

10 seconds - The RXLEV for cell B meets the minimum threshold (RLAM). The MS starts a timer assoon as it puts it on its strongest neighbor list. The penalty time for cell B is 40 seconds, so for the first 40

8/10/2019 GSM Timing advance and Cell re selection

14/15

seconds that cell B is on the strongest neighbor list it will apply the temporary offset to the C2 value.After including the offset, the C2 for cell B is -20 dBm.

20 seconds - The C2 for cell A continues to drop as the C2 for cell B continues to rise. With a C2 of 25,

cell A is still the most attractive.

30 seconds - Cell A drops to a C2 of 21 and cell B has a C2 of -5.

40 seconds - Cell A drops to a C2 of 18. Cell B rises to a C2 of 3. Notice here that if it were not for thetemporary offset, the C2 for cell B would be at 23. At this point the MS would normally reselect cell B.However, due to the temporary offset, cell A is still the most attractive.

50 seconds - At this point the penalty time for cell B has expired and the temporary offset is no longerapplied. The C2 for cell B raises from 3 to 27. The C2 for cell B wins over the C2 for cell A and the MSreselects cell B.

The temporary offset would be used if the network wanted to discourage mobile stations from reselectinga cell as soon as the MS saw it. This is commonly found in pico-cells. This forces a MS to be in the area

of the cell for a certain period before reselecting it. It prevents mobile stations that just happen to bepassing by from reselecting the cell. In order to reselect the cell, the MS must be in the area for a certainperiod of time or be close enough that the RXLEV overcomes the negative offset value.

Cell Reselection Offset (CRO)- CRO is a value from 0 to 63. Each step represents a 2 dBm step (0 to126 dBm). This value is added to C1. A higher CRO value will make the cell tower more attractive to theMS. The higher the CRO, the more attractive the cell will be. The network might assign a CRO value to a

cell if the network wanted to encourage mobile stations to utilize that cell. The network might want to do

this in order to reduce the load on other cells during times of high traffic volume or to force MS's to acertain band.

Neighbor List - The neighbor list is a list of the 6 strongest cells that the MS can see. The RXLEV forthese cells is transmitted in a measurement report from the MS to the BTS on the SACCH whenever theMS has been allocated an SDCCH or a TCH. The BSC and MSC use these measurements to determine ifthe MS needs to move to a different cell. Whenever a cell is in an active SDCCH or TCH the network willalways manage the handoff. The MS will only move from one cell to another by itself when it is in idle

mode.

8/10/2019 GSM Timing advance and Cell re selection

15/15

Cell Reselection Hysteresis (CRH)

When a MS reselects a new cell it does not need to notify the network unless that new cell is in adifferentLocation Area.When a MS moves into a new location area it must do alocation updatewhich

generates signal messaging between the BTS, BSC, MSC, VLR, and HLR. If a MS is located along theborder of two location areas then it will see cells in both location areas. A MS along the borderline might

reselect a cell in one location area and then a few minutes later reselect a cell in the other location areaand continuously bounce back and forth between location areas generating too much signaling overhead

and putting strain on the network.

In order to mitigate this problem the CRH is used. It is a value that is similar to the temporary offset valueof C2. CRH is applied to C2 when the desired cell is in a different location area. This results in makingthe cell in this different location area less desirable to the MS. The MS must move close enough to the

new location area to overcome the offset thus ensuring the MS is truly close enough to the new locationarea to warrant a location update. Once the MS reselects the cell in the new location area it will perform a

location update. The MS will then apply the CRH value to all cells it sees in the old location area whichwill make them less attractive to the MS and ensure the MS does not continually bounce back and forth

between two location areas.

Cell Bar Access (CBA)

Cell Bar Access is a single bit (0 or 1) value sent down on the BCCH. If CBA is set to 1 then MS's are not

allowed to select that cell. If the value is set to 0 then MS's may select it. CBA would be used on umbrella

cells in order to prevent MS's from selecting it. The umbrella cell would be reserved for when the networkneeds to manage high levels of traffic. This gives the network total control of access to the umbrella cell.

Cell Bar Qualifier (CBQ)

This value is similar to the CBA but it applies to reselection. A cell that has CBQ set to 1 does not allowMS's to reselect it. CBQ set to 0 allows normal access to that cell.

Signal Strength RXQUAL Cell Selection and Reselection C1 C2 Cell Reselection Offset Cell

Reselection Hysteresis Cell Bar Access Cell Bar Qualifier

Introduction Architecture TDMA Logical Channels Authentication & Encryption Timing

Advances Speech Encoding GSM Events Cell Selection/Reselection

Updates Sitemap Contact Me

http://gsmfordummies.com/architecture/arch.shtml#vlrhttp://gsmfordummies.com/architecture/arch.shtml#vlrhttp://gsmfordummies.com/architecture/arch.shtml#vlrhttp://gsmfordummies.com/gsmevents/location_update.shtmlhttp://gsmfordummies.com/gsmevents/location_update.shtmlhttp://gsmfordummies.com/gsmevents/location_update.shtmlhttp://gsmfordummies.com/air/radiolink.shtml#sighttp://gsmfordummies.com/air/radiolink.shtml#sighttp://gsmfordummies.com/air/radiolink.shtml#rxqualhttp://gsmfordummies.com/air/radiolink.shtml#rxqualhttp://gsmfordummies.com/air/radiolink.shtml#selrelhttp://gsmfordummies.com/air/radiolink.shtml#selrelhttp://gsmfordummies.com/air/radiolink.shtml#c1http://gsmfordummies.com/air/radiolink.shtml#c1http://gsmfordummies.com/air/radiolink.shtml#c2http://gsmfordummies.com/air/radiolink.shtml#c2http://gsmfordummies.com/air/radiolink.shtml#crohttp://gsmfordummies.com/air/radiolink.shtml#crohttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#cbahttp://gsmfordummies.com/air/radiolink.shtml#cbahttp://gsmfordummies.com/air/radiolink.shtml#cbqhttp://gsmfordummies.com/air/radiolink.shtml#cbqhttp://gsmfordummies.com/intro/intro.shtmlhttp://gsmfordummies.com/intro/intro.shtmlhttp://gsmfordummies.com/architecture/arch.shtmlhttp://gsmfordummies.com/architecture/arch.shtmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://gsmfordummies.com/tdma/logical.shtmlhttp://gsmfordummies.com/tdma/logical.shtmlhttp://gsmfordummies.com/encryption/encryption.shtmlhttp://gsmfordummies.com/encryption/encryption.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/encoding/encoding.shtmlhttp://gsmfordummies.com/encoding/encoding.shtmlhttp://gsmfordummies.com/gsmevents/events.shtmlhttp://gsmfordummies.com/gsmevents/events.shtmlhttp://gsmfordummies.com/air/radiolink.shtmlhttp://gsmfordummies.com/air/radiolink.shtmlhttp://gsmfordummies.com/updates.shtmlhttp://gsmfordummies.com/updates.shtmlhttp://gsmfordummies.com/sitemap.shtmlhttp://gsmfordummies.com/sitemap.shtmlhttp://gsmfordummies.com/contact/contact.shtmlhttp://gsmfordummies.com/contact/contact.shtmlhttp://gsmfordummies.com/contact/contact.shtmlhttp://gsmfordummies.com/sitemap.shtmlhttp://gsmfordummies.com/updates.shtmlhttp://gsmfordummies.com/air/radiolink.shtmlhttp://gsmfordummies.com/gsmevents/events.shtmlhttp://gsmfordummies.com/encoding/encoding.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/timing/timing.shtmlhttp://gsmfordummies.com/encryption/encryption.shtmlhttp://gsmfordummies.com/tdma/logical.shtmlhttp://gsmfordummies.com/tdma/tdma.shtmlhttp://gsmfordummies.com/architecture/arch.shtmlhttp://gsmfordummies.com/intro/intro.shtmlhttp://gsmfordummies.com/air/radiolink.shtml#cbqhttp://gsmfordummies.com/air/radiolink.shtml#cbahttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#crhhttp://gsmfordummies.com/air/radiolink.shtml#crohttp://gsmfordummies.com/air/radiolink.shtml#c2http://gsmfordummies.com/air/radiolink.shtml#c1http://gsmfordummies.com/air/radiolink.shtml#selrelhttp://gsmfordummies.com/air/radiolink.shtml#rxqualhttp://gsmfordummies.com/air/radiolink.shtml#sighttp://gsmfordummies.com/gsmevents/location_update.shtmlhttp://gsmfordummies.com/architecture/arch.shtml#vlr