GSM Frequency Planning ISSUE2 0

www.huawei.com

Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved.

GSM Frequency

Planning

Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved. Page2

Contents

1. Frequency Planning

2. Normal Frequency Reuse Technology

3. Tight Frequency Reuse

4. Multiple Reuse Pattern Technology

5. Concentric Cell Technology

6. Frequency Hopping


Contents

1. Frequency Planning Basic

1.1 Frequency Resource of GSM System

1.2 Concept of Frequency Reuse

1.3 Reuse Density

1.4 C/I Ratio


P-GSM 900 :

DCS 1800 :

1710 1785 1805 1880

Duplex distance : 95 MHz

890 915 935 960

Duplex distance : 45 MHz

Frequency Resource of GSM System


Frequency Resource of GSM System

Frequency

Spectrum

Range

(MHz)

Uplink

Frequency Value ARFCN

Downlink

Frequency Value

P-GSM900 890~915

935~960 Fu(n)=890+0.2n 1n 124 Fd(n)=Fu(n)+45

E-GSM900 880~915

925~960

Fu(n)=890+0.2n

Fu(n)=890+0.2(n-1024)

0 n 124

975 n 1023 Fd(n)=Fu(n)+45

R-GSM900 876~915

921~960

Fu(n)=890+0.2n

Fu(n)=890+0.2(n-1024)

0 n 124

955 n 1023 Fd(n)=Fu(n)+45

DCS1800 1710~1785

1805~1880 Fu(n)=1710.2+0.2(n-512) 512 n 885 Fd(n)=Fu(n)+95

PCS1900 1850~1910

1930~1990 Fu(n)=1850.2+0.2(n-512) 512 n 810 Fd(n)=Fu(n)+80


{fi,fj..fk}

{fi,fj..fk} {fi,fj..fk} {fi,fj..fk} .. ..

Macro-cell system

d

Micro-cell system

Concept of Frequency Reuse


Example of Frequency Reuse

Frequency resource is limited. If there is 8MHz frequency

resource, 8 MHz = 40 channels 8 timeslots = 320

Max. 320 users can access the network at the same time.

If every frequency is reused N times

Max. 320N uses can access the network at the same time.


The spectrum utilization ratio can be expressed by frequency reuse

density (freuse), which reveals the tightness of the frequency reuse and

can be expressed by the following equation

NARFCN is the total number of the available channel numbers,

NTRX is the number of TRXs configured for the cell.

Reuse Density

TRX

ARFCNreuse

N

Nf


Question

(1) Frequency bandwidth is 12MHZ, if frequency reuse density

is 4x3,each cell has how many TRX?

(2) Frequency bandwidth is 6MHZ, if frequency reuse density

is 2x3,each cell has how many TRX?


Looser reuse

Higher frequency reuse efficiency,

but interference is serious.

More technique is needed.

Tighter reuse

0 12 20

Little interference,

but frequency reuse efficiency is low.

Reuse Density

Reuse density is the number of cells in a basic reuse cluster.

For the n x m frequency reuse pattern,

n: The number of BTSs in the reuse clusters

m: The number of the cells under each BTS.

mnfreuse


43 Frequency Reuse

A1

C1

B1

D1 A2

A3 B2

B3

C2

C3 D2

D3

A1

C1

B1

D1 A2

A3 B2

B3

C2

C3 D2

D3

A1

C1

B1

D1 A2

A3

B2

B3

C2

C3 D2

D3 A1

C1

B1

D1 A2

A3

B2

B3

C2

C3 D2

D3

A1 C1

B1

D1 A2

A3 B2

B3

C2

C3 D2

D3

A1

C1

B1

D1

A2

A3 B2

B3

C2

C3 D2

D3


Requirement for C/I Ratio

All useful signals Carrier

All useless signals Interference =

Useful signal Noise from environment

Other signals

C/I =


Requirement for C/I Ratio

Interference C/I C/I in Actual Project

(3 dB margin is needed )

Co-channel 9dB 12dB

Adjacent-channel - 9dB - 6dB

Carrier offset reaches 400 KHz - 41dB


Exercise

Cell A fre 5

Cell C fre 4

Cell D fre 3 Cell B fre 5 ?dB<

?dB<

?dB<

-70dB


Contents








Example of 4 x 3 Frequency Reuse Hereunder are several assumptions

The available bandwidth is 10MHz. The channel number is 45~94

BCCH 81~94 (14 channel numbers in total, 81~82 are reserved)

The other channel numbers are allocated to TCH

So the maximum base station configuration is S4/4/4, and the

frequency reuse density is 12.5 (50/4 = 12.5)

Frequency group

number A1 B1 C1 D1 A2 B2 C2 D2 A3 B3 C3 D3

Channel Number

of Each

Frequency Group

94 93 92 91 90 89 88 87 86 85 84 83

80 79 78 77 76 75 74 73 72 71 70 69

68 67 66 65 64 63 62 61 60 59 58 57

56 55 54 53 52 51 50 49 48 47 46 45


4 x 3 Frequency Reuse Conclusion The 4 x 3 frequency reuse pattern is a basic technology applied in frequency planning.

Which must be applied to the BCCH in frequency aggressive reuse technologies

If the network capacity needs to be further expanded, the following measures can be

taken:

Split a cell into smaller cells.

Utilize new frequency resources. For example, you can establish a DSC 1800MHz

network.

Under the current 900MHz network, use more tight frequency reuse technology to

expand the network capacity.

At present, the tight frequency reuse technology works as the most economical and

convenient way to expand the network capacity, so it is also the most popular with

carriers.

The typical frequency reuse technology includes 3 x 3, 2 x 6, 2 x 3, 1 x 3, and 1 x 1.


Contents








1 x 3 Frequency Reuse Pattern 1 x 3 frequency reuse pattern is also called

fractional reuse.

For 1 x 3 or 1 x 1 frequency reuse pattern,

the reuse distance is quite small, so the

interference in the network is quite great.

Therefore, to avoid frequency collision, you

must use RF hopping technology and set the

parameters, including MA (mobile allocation),

HSN (hopping sequence number), and

MAIO (mobile allocation index offset). The

ratio of number of the TRXs to that of the

available frequency hopping is FR LOAD

(generally, it is smaller than 50%).

A1 A2

A3

A1 A2

A3

A1 A2

A3

A1 A2

A3


Example of 1 x 3 Frequency Reuse

If the available bandwidth is 10MHz ,the channel numbers are 45~94

For BCCH carriers, channel numbers is 81~94, frequency reuse pattern is 43

For TCH carriers, channel numbers is 45~80, frequency reuse pattern is 13

Because FR LOAD 1 to 2, if the bandwidth is 10MHz, the maximum base station

type can be configured as S7/7/7. In this case, the frequency reuse degree is 7.14

Frequency group number Channel number MAIO

A 80, 77, 74, 71, 68, 65, 62, 59, 56, 53, 50, 47 0, 2, 4,6, 8, 10

B 79, 76, 73, 70, 67, 64, 61, 58, 55, 52,49, 46 1, 3, 5, 7, 9, 11

C 78, 75, 72, 69, 66, 63, 60, 57, 54, 51, 48, 45 0, 2, 4, 6, 8, 10

space

grouping


A 80, 79, 78, 77, 76, 75, 74, 73,72, 71, 70, 69 0, 2, 4, 6, 8, 10

B 68, 67, 66, 65, 64, 63, 62, 61, 60, 59, 58, 57 0, 2, 4, 6, 8, 10

C 56, 55, 54, 53, 52, 51, 50, 49, 48, 47, 46, 45 0, 2, 4, 6, 8, 10

sequence

grouping


Example of 13 Frequency Reuse

Suppose 900 band: 96124

BTS configuration: S3/3/3

BCCH layer: 96109 reuse pattern: 43

TCH layer: 110124 reuse pattern: 13


TCH Consecutive Allocation Scheme

MAIO

CELL1(MA1) 110 111 112 113 114 0,2

CELL2(MA2) 115 116 117 118 119 0,2

CELL3(MA3) 120 121 122 123 124 0,2

MA1

MA2 MA3

Cell1

Cell2 Cell3

MA1

MA2 MA3

Cell1

Cell2 Cell3

MA1

MA2 MA3

Cell1

Cell2 Cell3

(110,112)

(110,112)

(110,112)

(115,117)

(115,117)

(115,117)

(120,122)

(120,122)

(120,122)


TCH Interval Allocation Scheme

MAIO

CELL1(MA1) 110 113 116 119 122 0,1

CELL2(MA2) 111 114 117 120 123 2,3

CELL3(MA3) 112 115 118 121 124 4,0

MA1

MA2 MA3

Cell1

Cell2 Cell3

MA1

MA2 MA3

Cell1

Cell2 Cell3

MA1

MA2 MA3

Cell1

Cell2 Cell3

(110,113) (110,113)

(110,113)

(117,120) (117,120)

(117,120)

(124,112) (124,112)

(124,112)


The Characteristics of the 1 x 3

The frequencies are more tightly reused, so the network capacity is great.

When planning a network, only need to plan BCCH, while its unnecessary to re-

plan frequencies. So the efficiency for network planning is high.

Wideband combiner must be used, but the cavity combiner with frequency

selectivity is inapplicable.

Co-channel and neighbor channel interference increases as the frequency reuse

distance decreases.

RF hopping must be used, and the channel numbers participating frequency

hopping is twice that of the number of carriers at least.

In actual conditions, BCCH cannot take measures, such as RF hopping, DTX, and

power control, therefore, in order to ensure network quality, BCCH can only use

the looser 4 x 3 frequency reuse pattern.


Example of 1 x 1 Frequency Reuse One cell of one base station forms a frequency reuse cluster

If the available bandwidth is 6MHz ,the channel numbers are 96~124

For BCCH carriers, channel numbers is 111~124, frequency reuse pattern is 43

For TCH carriers, channel numbers is 96~110, frequency reuse pattern is 11

the maximum base station type can be configured as S4/3/3 under 1 x 1

frequency reuse pattern. In this case, the frequency reuse degree is

7.25/9.67/9.67, so the average value is 8.86.

Therefore, the maximum base station configuration under 1 x 1 frequency reuse

pattern is the same as that under 1 x 3 frequency reuse space grouping pattern,

so is the network capacity.


A 96,97,98,99,100,101,102,103,104,105,106,107,108,109,110 0,2,4

B 96,97,98,99,100,101,102,103,104,105,106,107,108,109,110 6,8

C 96,97,98,99,100,101,102,103,104,105,106,107,108,109,110 10,12


BCCH14+TCH36

1BCCH+3TCH

1BCCH+3TCH 1BCCH+3TCH

1BCCH+12TCH


43

13

13 and 11

1BCCH+TCH


11


TRX1 TRX2 ... TRX7

TRX8 TRX9... TRX14 TRX15 TRX16...TRX21

TRX1 TRX2 ... TRX7

TRX8 TRX9... TRX14 TRX15 TRX16...TRX21

The red items are BCCH RCs

Illustration of 13 or 11


Contents








Conception of MRP Technology

According to multiple reuse pattern (MRP), the carriers are

divided into several groups.

The carries in each group work as an independent layer,

and each layer uses a different frequency reuse pattern.

During frequency planning, configure the carriers layer by

layer, with reuse density increases layer by layer, as shown

in the next slide.


Conception of MRP Technology


Capacity increase when reuse density is multiplied:

Supposing there are 300 cells

Bandwidth: 8 MHz (40 frequency)

Normal 43 reuse: reuse density=12

Network capacity = (40/12)300 = 1000 TRX

Multiple reuse:

BCCH layer: re-use =12, (14 frq.)

Normal TCH layer: re-use =10, (20 frq.)

Aggressive TCH layer: re-use = 6, (6 frq.)

Network capacity = (1 +2 +1)300 = 1200 TRX

Example of MRP


Example of MRP

Capacity increase when reuse density is multiplied:

Supposing there are 300 cells

Bandwidth: 8 MHz (40 frequency)

Normal 43 reuse: reuse density=12

Network capacity = (40/12)300 = 1000 TRX

Multiple reuse:

BCCH layer: reuse density=12, (14 frequency)

Normal TCH layer: reuse density=10, (20 frequency)

Aggressive TCH layer: reuse density= 6, (6 frequency)

Network capacity = (1 +2 +1)300 = 1200 TRX


Contents








Conception of Concentric Cell Technology

In the GSM network, concentric cell technology is used to divide the

service area into two parts: overlaid and underlaid.

Essentially, the concentric cell technology concerns channel allocation and

handover, but when combining this technology with various frequency

planning technologies, both expand network capacity can be improved

network quality.

Overlaid-cell

Underlaid-cell


Overlaid/Underlaid Frequency Configuration

Super fn

Regular fm Regular fm Regular fm

Super fn

BCCH 15f Regular 24f Super 12f

BCCH TRX reuse density: 12

Regular TCH TRX reuse density: 12

Super TCH TRX reuse density: 6

Super fn


Conception of Concentric Cell Technology

Generally, 4 x 3 frequency reuse pattern is used for the underlaid. For

overlaid, the frequency reuse patterns, such as 3 x 3, 2 x 3, or 1 x 3, are

used. Therefore, all carriers can be divided into two groups, one for

underlaid, and the other one for overlaid.

Underlaid Overlaid


Contents








Contents


6.1 Classification of hopping

6.2 Advantages of hopping

6.3 Parameter of hopping

6.4 Collocation of hopping data


Frequency Hopping


Advantages of Hopping

Get an agreeable radio environment.

Provide a similar communication quality for every user.

Tighter reuse patterns are possible to be used for larger

capacity.


Smoothen the rapid fading (Rayleigh fading)

Frequency Diversity of Hopping


Smoothen and average the interference

Interference Diversity of Hopping


Classification of Hopping

According to implementation mode

Base-band hopping

RF hopping

According to the minimum hopping time unit

Timeslot hopping

Frame hopping


Base Band Hopping Principle

FH bus



BCCH carrier attends hopping, on which TS0 can not attend hopping

No Hopping TRX0

TRX1

TRX2

TRX3

TS 0 TS 1 TS 2 TS 3 TS 4 TS 5 TS 6 TS 7 ARFCN

5(BCCH carrier)

10(TCH carrier)

15(TCH carrier)

20(TCH carrier)

MA={5,10,15,20} MA={10,15,20}



BCCH carrier does not attends hopping

TRX0

TRX1

TRX2

TRX3

TS 0 TS 1 TS 2 TS 3 TS 4 TS 5 TS 6 TS 7

MA={10,15,20}

ARFCN

5(BCCH carrier)

10(TCH carrier)

15(TCH carrier)

20(TCH carrier)

No Hopping No Hopping No Hopping No Hopping No Hopping No Hopping No Hopping No Hopping


RF Hopping Principle


RF Hopping Principle

BCCH carrier does not attends hopping

TRX0

TRX1

TRX2

TRX3

TS 0 TS 1 TS 2 TS 3 TS 4 TS 5 TS 6 TS 7

No Hopping No Hopping No Hopping No Hopping No Hopping No Hopping No Hopping No Hopping

MA={10,15,20}

MA={10,15,20}

MA={10,15,20}

(BCCH carrier)

(TCH

carrier)


Classification of Hopping

Frame hopping

Frequency changes every TDMA frame.

The different channel of one TRX uses the same MAIO.

Timeslot hopping

Frequency changes every timeslot.

The different channel of one TRX uses the different MAIO.


Frame Hopping

f 0

Frame 0

f 1

f 2

f 3

f 4

Frame 1 Frame 2 Frame 3 Frame 4

One TRX (none BCCH carrier) hopping on 5 frequencies

RF hopping and baseband hopping without BCCH carrier


Timeslot Hopping

f 0

Frame 0

f 1

f 2

f 3

f 4


5 timeslots on 1 TRX hopping on 5 frequencies


Hopping Parameters

All the parameters which are related to hopping are

configured in Cell Attributes/Frequency Hopping.

Hopping mode: the mode used by the BTS system

No hopping

Base band hopping

RF hopping


Hopping Parameters

HSNHopping Sequence Number063

HSN=0cycle hopping.

HSN0random hopping. Every sequence number

corresponds a pseudo random sequence.


Hopping Parameters

MA (Mobile Allocation Set):

MA is the set of available RF bands when hopping, containing at most 64

frequency carriers. The frequency being used must be those of the available

frequency

MAIO (Mobile Allocation Index Offset)

MAIO is used to define the initial frequency of the hopping.

Be careful to configure the MAIO of same timeslot in all channels, otherwise

interference occurs.

MAI (Mobile Allocation Index)

At the air interface, the frequency used on a specific burst is an element in MA

set. MAI is used for indication, referring to a specific element in the MA set.

MAI is the function of TDMA FN, HSN and MAIO.


Example of MAIO

No Hopping 0

2

1

2

2

2

3

2

0

2

1

2

2

2

0 1 1

2

2

2

3

2

0

2

1

2

2

2

3

2

1 1 2

2

3

2

0

2

1

2

2

2

3

2

0

2

2 1 3

2

0

2

1

2

2

2

3

2

0

2

1

2

TRX0

TRX1

TRX2

TRX3


5(BCCH carrier)

10(TCH carrier)

15(TCH carrier)

20(TCH carrier)

MA2={5,10,15,20} MA1={10,15,20}

MAIO 0 1 2 MAIO 0 1 2 3

MAIO MAI


Example of MAIO

No Hopping 0

2

1

2

2

2

3

2

0

2

1

2

2

2

0 1 1

2

2

2

3

2

0

2

1

2

2

2

3

2

1 1 2

2

3

2

0

2

1

2

2

2

3

2

0

2

2 1 3

2

0

2

1

2

2

2

3

2

0

2

1

2

0 3 1

3

2

3 3 3

0

3

1

3

2

3

3

3

1 3 2

3

3

3

0

3

1

3

2

3

3

3

0

3

2 3 3

3

0

3

1

3

2

3

3

3

0

3

1

3

3 3 0

3

1

3

2

3

3

3

0

3

1

3

2

3

TRX0

TRX1

TRX2

TRX3


5(BCCH carrier)

10(TCH carrier)

15(TCH carrier)

20(TCH carrier)

MA2={5,10,15,20}

MA1={10,15,20}

MA3={510,515,520,525}

510(TCH carrier)

515(TCH carrier)

520(TCH carrier)

525(TCH carrier)

TRX4

TRX5

TRX6

TRX7


Example of MAIO

5

Frame 0

10

15

20

25


MA={5,10,15,20,25}

5 TRXs separately belongs to the same MA hopping on 5 frequencies, and uses same HSNs


Example of Hopping Parameters

f 0

Frame 0

f 1

f 2

f 3

f 4


8 timeslots of 1 TRX separately belongs to different MAs hopping on 5 frequencies, and uses different HSNs.


Example of Hopping Parameters

f 0

Frame 0

f 1

f 2

f 3

f 4


5 TRXs separately belongs to different MAs hopping on 5 frequencies, and uses different HSNs

Thank you www.huawei.com

GSM Frequency Planning ISSUE2 0

Documents

Transcript of GSM Frequency Planning ISSUE2 0