GS81 IEEEXplore Config

1
Configuration of GhostScript 8.1, for use with GhostView 4.6, to produce Xplore-Compatible PDFs Note: GhostScript 8.1 is currently recognized as the latest stable version of GhostScript (Jun-2004) (1) Open GhostView (note that GhostScript should be installed before GhostView) (2) Select File->Convert… (3) Set Device = pdfwrite (4) Set Resolution = 600 (5) Click “Properties”, and set each property to the value listed below. (6) Click OK to save settings, click OK again to generate PDF, entering the filename+.pdf IMPORTANT: You must enter the file extension (.pdf) manually, as described above. Property Value CompatibilityLevel 1.4 PDFSETTINGS [Not defined] AutoRotatePages /None CompressPages true ASCII85EncodePages false UseFlateCompression true EmbedAllFonts true SubsetFonts true MaxSubsetPct 100 ConvertCMYKImagesToRGB false AutoFilterColorImages true ColorImageFilter /DCTEncode EncodeColorImages true DownsampleColorImages true ColorImageDepth -1 ColorImageResolution 300 ColorImageDownsampleThreshold 1 ColorImageDownsampleType /Bicubic AutoFilterGrayImages true GrayImageFilter /DCTEncode EncodeGrayImages true DownsampleGrayImages true GrayImageDownsampleThreshold 1 GrayImageDownsampleType /Bicubic GrayImageDepth -1 GrayImageResolution 300 MonoImageFilter /CCITTFaxEncode EncodeMonoImages true DownsampleMonoImages true MonoImageDownsampleThreshold 1 MonoImageDownsampleType /Bicubic MonoImageDepth -1 MonoImageResolution 600

description

IEEE guideline

Transcript of GS81 IEEEXplore Config

Page 1: GS81 IEEEXplore Config

Configuration of GhostScript 8.1, for use with GhostView 4.6, to produce Xplore-Compatible PDFs Note: GhostScript 8.1 is currently recognized as the latest stable version of GhostScript (Jun-2004)

(1) Open GhostView (note that GhostScript should be installed before GhostView) (2) Select File->Convert… (3) Set Device = pdfwrite (4) Set Resolution = 600 (5) Click “Properties”, and set each property to the value listed below. (6) Click OK to save settings, click OK again to generate PDF, entering the filename+.pdf

IMPORTANT: You must enter the file extension (.pdf) manually, as described above. Property Value CompatibilityLevel 1.4 PDFSETTINGS [Not defined] AutoRotatePages /None CompressPages true ASCII85EncodePages false UseFlateCompression true EmbedAllFonts true SubsetFonts true MaxSubsetPct 100 ConvertCMYKImagesToRGB false AutoFilterColorImages true ColorImageFilter /DCTEncode EncodeColorImages true DownsampleColorImages true ColorImageDepth -1 ColorImageResolution 300 ColorImageDownsampleThreshold 1 ColorImageDownsampleType /Bicubic AutoFilterGrayImages true GrayImageFilter /DCTEncode EncodeGrayImages true DownsampleGrayImages true GrayImageDownsampleThreshold 1 GrayImageDownsampleType /Bicubic GrayImageDepth -1 GrayImageResolution 300 MonoImageFilter /CCITTFaxEncode EncodeMonoImages true DownsampleMonoImages true MonoImageDownsampleThreshold 1 MonoImageDownsampleType /Bicubic MonoImageDepth -1 MonoImageResolution 600

Config Autoqos

Config Autoqos

ASA Config

ASA Config

Config File

Config File

February 2018 Vertec Software Release 6...5 Config Sets 33 5.1 Config Set dialogue 33 5.2 Importing Config Sets 33 5.3 Creating Config Sets 35 5.4 Config Set XML 37 5.5 Using the Entry

February 2018 Vertec Software Release 6...5 Config Sets 33 5.1 Config Set dialogue 33 5.2 Importing Config Sets 33 5.3 Creating Config Sets 35 5.4 Config Set XML 37 5.5 Using the Entry

e-config Installation Guidelines - IBM WWW Page e-config Installation Guidelines Page 1 of 43 e-config Upgrade Installation Guidelines Version 1.0 Author: e-config Team Owner: e-config

e-config Installation Guidelines - IBM WWW Page e-config Installation Guidelines Page 1 of 43 e-config Upgrade Installation Guidelines Version 1.0 Author: e-config Team Owner: e-config

TACACS.net Config

TACACS.net Config

Ldom Config

Ldom Config

TSI1000 Config

TSI1000 Config

python-icat - A Library for Writing ICAT Clients in Python · Using python-icat config = icat . config . Config conf = config . getconfig client = icat . Client ( conf . url , conf

python-icat - A Library for Writing ICAT Clients in Python · Using python-icat config = icat . config . Config conf = config . getconfig client = icat . Client ( conf . url , conf

Smart Config

Smart Config

Tvlsi Kuang Ieeexplore

Tvlsi Kuang Ieeexplore

 · Web viewSetting device to VTP Server mode for VLANS DLS1(config)# vlan 10 DLS1(config-vlan)# name Finance DLS1(config-vlan)# vlan 20 DLS1(config-vlan)# name Engineering DLS1(config-vlan)#

 · Web viewSetting device to VTP Server mode for VLANS DLS1(config)# vlan 10 DLS1(config-vlan)# name Finance DLS1(config-vlan)# vlan 20 DLS1(config-vlan)# name Engineering DLS1(config-vlan)#

Config main

Config main

SMS Config

SMS Config

INTRODUCING OPEN SOURCE MANO · Config. vSwitch Config. NIC Config. Acceleration Config. ... Basic NSD BASIC AND HAND-MADE NETWORK SERVICE ... •No other commercial distros were

INTRODUCING OPEN SOURCE MANO · Config. vSwitch Config. NIC Config. Acceleration Config. ... Basic NSD BASIC AND HAND-MADE NETWORK SERVICE ... •No other commercial distros were

Config Options

Config Options

Installation Config

Installation Config

ConfiguringSecurity - Cisco€¦ · apic1(config-host)# timeout 3 apic1(config-host)# descr "My primary RADIUS server" apic1(config-host)# key myRaDiUSpassWoRd apic1(config-host)#

ConfiguringSecurity - Cisco€¦ · apic1(config-host)# timeout 3 apic1(config-host)# descr "My primary RADIUS server" apic1(config-host)# key myRaDiUSpassWoRd apic1(config-host)#

On EC/ Temp. Limit Alarm PRI PRF Display measurement value xx.xx µS / xxx.x mS CONFIG 1 CONFIG 2 CONFIG 3 CONFIG 4 CONFIG 5 LANGUAGE TEMPERATURE DISPLAY CHANNEL 1 RELAIS 1 CHANNEL

On EC/ Temp. Limit Alarm PRI PRF Display measurement value xx.xx µS / xxx.x mS CONFIG 1 CONFIG 2 CONFIG 3 CONFIG 4 CONFIG 5 LANGUAGE TEMPERATURE DISPLAY CHANNEL 1 RELAIS 1 CHANNEL

Airport Config

Airport Config