GS 900 Ceiling Mount Assembly Instructions

GS 900 Ceiling Mount Assembly Instructions

• Dear User,

The ceiling mount should only be installed by a technical expert (electrical engineer, technician) or a comparably qualified person.

GS 900 Ceiling Mount Assembly Instructions

• Ships in 3 boxes:

GS 900 Ceiling Mount Assembly Instructions

• Box 1: Ceiling Mount Swing/Extension Arms

GS 900 Ceiling Mount Assembly Instructions

• Box 1 Contents

Operating Manual Installation Instructions Hardware Kit

GS 900 Ceiling Mount Assembly Instructions

• Box 2: Spacer Tube Box

GS 900 Ceiling Mount Assembly Instructions

• Contents of Box 2:

Drilling Template

Installation Instructions

Spacer Tube

GS 900 Ceiling Mount Assembly Instructions• Please note parts located in the plastic sleeve of the spacer tube

as indicated below

View from top

GS 900 Ceiling Mount Assembly Instructions

• Box 3

Luminaire

GS 900 Ceiling Mount Assembly Instructions

Mounting Spacer Tube

Note: Spacer Tube is designed to accommodate ceilings between 8-10ft. Tubing is shipped to accommodate a10 ft ceiling and can be shortened to accommodate an 8ft. ceiling. If at all possible, secure mounting plate 10 ft off the floor (even if this requires mounting the plate above a false ceiling).

If shortening is required follow instructions on next 4 pages.

GS 900 Ceiling Mount Assembly Instructions

Shortening Spacer Tube• Remove wires from terminal

block on the mounting plate

Remove pin/steel bearing sleeve and wires running inside spacer tube

GS 900 Ceiling Mount Assembly Instructions

• Trim spacer tube to accommodate actual ceiling height.

• Drill and tap 3 holes (5mm diameter and M6 thread)– Use drill template provided with Ondal Installation Instructions (or

dimensions on next page)

Place drill template at the edge of the tube

GS 900 Ceiling Mount Assembly Instructions

• Drilling Template (dimensions in millimeters)

GS 900 Ceiling Mount Assembly Instructions

• Reinstall wire through tubing and into terminal blockGround wire to mounting plate

Insert other two set screws and tighten

Insert set screw with additional length ensuring screw engages the hole in the pin/steel bearing sleeve

GS 900 Ceiling Mount Assembly Instructions

Mounting Spacer Tube

• Loosen three threaded pins/set screws(1) and remove fixture flange/bezel(2)

• Using the drilling template (or with dimensions on next page) fasten spacer tube mounting plate to the ceiling

• The indicated transformer is not part of the GS900 system and is not supplied with the assembly (see wiring instructions on page 17)

Transformer

Mounting Plate

GS 900 Ceiling Mount Assembly Instructions• Drilling Template Dimensions

GS 900 Ceiling Mount Assembly Instructions

• Connecting power wires

Domestic (see above image)Black -- HotWhite -- NeutralGreen – Green/yellow -- Ground

Wiring Instructions

InternationalBrown -- HotOrange -- NeutralGreen – Yellow -- Ground

GS 900 Ceiling Mount Assembly Instructions

Remove and discard protective cover

Connecting Spring Arm to Extension Arm

GS 900 Ceiling Mount Assembly Instructions

Remove plastic cap/electrical connector from one end of the extension arm

GS 900 Ceiling Mount Assembly Instructions

Slide spring arm bearing into extension arm Place washer

Install Spring Clip using tool Replace plastic cap/electrical connector and secure with screw

GS 900 Ceiling Mount Assembly Instructions

Mounting Extension Arm to Spacer Tube

Remove plastic cap/electrical connector from other end of extension arm

Slide Extension Arm onto Spacer

Tube Bearing

GS 900 Ceiling Mount Assembly Instructions

Place washer

Place slotted cone inserting cone feature into hole in bearing

Install spring clip using tool

Please note: these parts are

located in the spacer tube bearing protective sleeve

GS 900 Ceiling Mount Assembly Instructions

Replace plastic cap/electrical connector and secure with screw

Please note: The spring tension of the spring arm is preset by the manufacturer (Ondal). The luminaire must be attached for the spring arm to balance.

GS 900 Ceiling Mount Assembly Instructions

Remove and discard protective cover

Attaching Luminaire to Spring Arm

GS 900 Ceiling Mount Assembly InstructionsLoosen the slotted screw

Loosen (do not remove) the Phillips head screw

Rotate plastic collar 180° to reveal key slot

GS 900 Ceiling Mount Assembly Instructions

• Insert luminaire into the spring arm

GS 900 Ceiling Mount Assembly Instructions

Place securing segmentcompletely into slot

GS 900 Ceiling Mount Assembly Instructions• Tighten Phillips head screw, turn plastic sleeve 180° and tighten slotted

screw

GS 900 Ceiling Mount Assembly Instructions• Turn on light to ensure it is working properly