GrowSpan Series 500 Door Kits - farmtek.com · 4. Attach stay rollers and the sliding door tracks...
Transcript of GrowSpan Series 500 Door Kits - farmtek.com · 4. Attach stay rollers and the sliding door tracks...
1Revision date: 04.30.19
STK# GS05KDR2SLT (Twin-Wall Polycarbonate)GS05KDR2SLC (Corrugated Polycarbonate)
Diagram shows a double-sliding door centered and installed in an end wall frame. The door kit includes materials for the door only. All other components shown in the diagram above and other diagrams throughout this guide are not included and require additional purchase.
Double Sliding Door
Finished Grade Finished Grade
©2019 GrowSpanAll Rights Reserved. Reproduction is prohibited without permission.
GrowSpan™ Series 500Door Kits
2 Revision date: 04.30.19
Table of ContentsDOUBLE SLIDING DOOR KIT: READ BEFORE YOU BEGIN
The double sliding door kit is designed to attach to any of these end frame kits: GS05KEW20G72, GS05KEW24G72, GS05KEW30G72 and GS05KEW35G72. These instructions and the instructions for the end frame are written to be used together.
Install the end wall framing before you install the door frame. Consider the positions of fans, vents, and other accessories before you install the door frame.
Door must not block or interfere with the operation of building accessories.
If you are installing this door kit in an end frame that is not identified above, use these instructions for critical dimensions and details.
Consult the services of a qualified contractor if needed. It is the responsibility of the owner/contractor to adapt these instructions to safely and competently install this door in an end frame or building that it was not designed for.
Complete these steps to begin and to install the door:
1. Based on the dimensions of the door (or doors), determine where you can position the door in the end frame. Use the diagrams from both this manual and the end wall assembly guide.
2. Secure the door framing to the end wall framing.
3. Assemble door frame and door and attach the assembled door to the door frame of the end wall. NOTE: If you purchased a fabric end panel to cover the end, install the panel before you install the door; then remove the panel material as needed to allow for the installation of the door. If you purchased a polycarbonate package (8mm twin-wall or corrugated), install those panels after installing the door frame and before installing the door. IMPORTANT: Consult the stay roller installation steps before installing the end wall polycarbonate panels.
Important Information ..............................................3Bearing Hangers .......................................................5Door Frame Assembly .............................................6Stay Roller Assembly ...............................................7Sliding Door Track Assembly ..................................8Adjust Doors .............................................................11Twin-Wall Single Sliding Door Assembly ...............12Corrugated Single Sliding Door Assembly ............14Shelter Care and Maintenance ................................16Quick Start Guide .....................................................17Door Frame Layout ...................................................18Door Frame Detail Connections ..............................19
3Revision date: 04.30.19
Important InformationREQUIRED TOOLS
The following list identifies the main tools needed to assemble the door. Additional tools and supports may be needed depending on the structure, location, and application.
• Tape measure or measuring device
• Fine point marker to mark the location frame members.
• Variable speed drill (cordless with extra batteries works the best)
• Drill bit set with 7/16" and 1/2" drill
• Wrench set
• Hammers, gloves, and eye protection
• Ladders, work platforms, and other machinery for lifting designed to work safely at the height of the door and door frame.
ATTENTION: Consult the services of a qualified, professional contractor if you are not familiar with the construction of similar frame structures and components.
YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT.
Thank you for purchasing this GrowSpan™ door kit. When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the door. Please read these instructions before you begin.
SAFETY PRECAUTIONS
• Wear eye protection.
• Wear head protection.
• Use a portable GFCI (Ground Fault Circuit Interrupter) when working with power tools and cords.
• Do not climb on the framing during or after construction.
• Provide proper ingress and egress to prevent entrapment. WARNING: The individuals assembling this door are responsible for designing and furnishing all temporary bracing, shoring and support needed during the assembly process. For safety reasons, those who are not familiar with recognized construction methods and techniques must seek the help of a qualified contractor.
FASTENERS
Fasteners are included to secure door components to metal frame members. If the building frame and cladding are not metal, purchase the appropriate fasteners locally, or call customer service for suggestions.
4 Revision date: 04.30.19
Important Information
PARTS IDENTIFICATION
The following graphics and photos will help identify the different hardware for each door kit. (Some parts are not shown.)
102921B & FA4484BTek Screws and neo-bonded washers
104213Aluminum U-Channel Profile(Twin-Wall Only)
104548End cap profile
100380Mounting bracket
ASSEMBLY PROCEDURE
Following the instructions as presented will help ensure the proper installation of the end frame and door. The steps outlining the assembly process are as follows:
1. Verify that all parts are included in the shipment. Notify Customer Service for questions or concerns.
2. Read these instructions and all additional documentation included with the shipment before you begin.
3. Gather the tools, bracing, ladders (and lifts), and assistance needed to install the door and door frame.
4. Read the care and maintenance information at the end of these instructions.
5. Complete and return all warranty information as instructed (if included).
UNPACK AND IDENTIFY PARTS
The following steps will ensure that you have all the necessary parts before you begin.
1. Unpack the contents of the shipment and place where you can easily inventory the parts. Refer to the Bill of Materials/Spec Sheets.
2. Verify that all parts listed on the Bill of Materials/Spec Sheets are present. If anything is missing or you have questions, consult the parts guide and all diagrams for clarification, or contact customer service. NOTE: At this time, you do not need to open the plastic bags containing smaller parts such as fasteners and clamps (if equipped).
QUICK START DIAGRAMS
For a quick overview of the end wall, door, and components, consult the diagrams located at the back of these instructions.
100356Stay roller
104709Horizontal closure strip
(Corrugated Only)
116391Bearing Hanger
5Revision date: 04.30.19
Bearing HangersASSEMBLE AND INSTALL SLIDING DOORS — OVERVIEW
The general steps to install the sliding doors are as follows:
1. Assemble the 102923 door frames.
2. Attach bearing hangers to the door frames.
3. Construct the rough opening in end wall frame.
4. Attach stay rollers and the sliding door tracks to the end wall.
5. Hang the sliding doors in the door track and adjust sliding doors as needed.
6. Attach polycarbonate panels to door frames.
7. Install 115581 screws through track to prevent door(s) from sliding out of the track.
8. Attach door handles and reinstall doors (if these were removed to install cladding).
ATTACH ROLLER ASSEMBLIES TO DOOR FRAMES
Complete the following steps to attach bearing hangers to the door frames.
1. Assemble 102923 door frames.
2. Locate and unpack the 116391 bearing hangers. Each door requires two (2) bearing hangers.
3. Insert mounting bolt through top of roller bearing and add one adjusting locknut.
4. Insert end of mounting bolt through mounting hole in top of door frame and add the remaining adjusting locknut. NOTE: Use 1/2" drill bit and drill to enlarge hole if bearing hanger bolt does not fit.
5. Repeat to attach remaining hanger to door frame.
Door Frame Tube
Adjusting Locknut
Adjusting Locknut
Mounting Adjusting Bolt
Bearing Hanger
6. Repeat steps to attach bearing hangers to remaining door frame.
7. Continue with next procedure.
ATTENTION: Use 1/2" drill bit and drill to enlarge hole if bearing hanger bolt does not fit.
6 Revision date: 04.30.19
Door Frame Assembly
S15P118 Header (cut to length)
90"
93"
Concrete Concrete
Finished Grade
(inside-to-inside)
Bottom of header to top of finished grade.
Door jamb anchored in concrete.
FinishedGrade
*Not shown to scale.
NOTE: End frame and rafter are not included with any door kit.
ASSEMBLING THE DOOR FRAME COMPONENTS
Consult the diagrams at the back of these instructions before you begin. Assistance is required to assemble the door frame and door. The following steps describe one way to assemble the door frame and door.
1. Using the dimensions on the Door Frame Layout diagram (Quick Start Section), determine the positions of the doorjambs.
2. Dig 8"-10" diameter holes at the locations found in previous step to a depth that is below the geographic frost line. Minimum depth: 24".
3. Using the rough door opening dimensions and the door frame components, assemble and install the door frame. See diagram below.
4. Square door frame and secure doorjambs in holes using concrete. Verify door frame dimensions before you secure jambs in concrete. Doorjambs must be plumb for proper door operation.
5. Once door frame is attached to end wall framing, assemble the door. Consult the procedures on the next few pages for your door (twin wall or corrugated polycarbonate).
Tek screws
QH1330
7Revision date: 04.30.19
Stay Roller AssemblyASSEMBLE AND ATTACH STAY ROLLERS
1. Locate the 100356 stay roller assembly and remove the roller, bushings, bolt, and nuts.
2. Secure the angle bracket in the lower-right corner of the assembled door frame as shown below. Allow clearance under bracket to attach stay roller.
Reattach the roller and related parts to the angled bracket attached to the end wall frame.
NOTE: Do not tighten the roller assembly at this time. It is adjusted and tightened when the door is installed.
ATTENTION: Stay roller assembly is attached to the door jamb on the same side the door is on when in the open position. For illustration purposes, the following diagrams show the roller assembly attached to the right side.
Assemble with the two brass bushing on the underside of the roller.
ATTENTION: After installing the stay roller, install the end wall cladding (polycarbonate panels or fabric panel). The polycarbonate panels of any end wall PC package must be installed before you install the sliding door assembly. Complete the installation of all polycarbonate panels at this time for these kits: GS05KCC2072 and GS05KCT2072, GS05KCC2472 and GS05KCT2472, GS05KCC3072 and GS05KCT3072, and GS05KCC3572 and GS05KCT3572.
Finished GradeFinished Grade
Position the stay roller at the corners of the door opening in the end wall framing.
Dashed line shows the approximate position of the sliding door track.
NOTE: Secure using 115581 pancake head screws if screws are not included with roller. Do not use the holes marked with an X in the diagram.
Doo
rjam
b
Header
Doo
rjam
b
DoorOpening
Outside of Building
Doo
rjam
b
Finished Grade
X
X
Door Opening
Finished Grade
8 Revision date: 04.30.19
Sliding Door Track AssemblyATTACH DOOR TRACK Gather the parts:
• FAK26 3/8" threaded rods, FALB04B 3/8" nuts, FAME18B 3/8" SS flat washers, FAMA38B lock washers, and FAME52B 3/8" flat washers
• FA4484B Tek screws and 102921B neo-bonded washers
• 100377 door tracks and 100380 hanger brackets for door track
Complete these steps to install the slider door tracks (100377). Complete only those steps that apply to the type of end wall polycarbonate (8mm twin-wall or corrugated) that covers the end frame.
1. Review diagram below for the slider track position. Space the five (5) track hanger brackets (100380) evenly along the slider track with one in the center at the joint between the two slider tracks. ATTENTION: Install hangers in a position so the mounted track is above the top of the door header. Add another end wall horizontal tube if needed to correctly mount the slider track. Door opening is smaller than the actual sliding door frame to prevent doors from pushing into the opening when closed. The position of the sliding door frames when installed and closed will align with the header and doorjambs of the end wall door frame.
Position of slider track above door opening. 100380 Bracket
slider trackslider track
Doo
rjam
b
Doo
rjam
b
Finished GradeFinished Grade
Center of the door opening.
9Revision date: 04.30.19
Sliding Door Track Assembly
Mark bracket positions on end wall cladding. Space brackets evenly along the length of slider track. For corrugated panels, drill 7/16" mounting holes in the valleys of the panels. Shift brackets left or right as needed. Drill one 7/16" hole through the end wall cladding and steel tube framing for each bracket. Drill holes level and straight through the tube to mount the brackets and track properly. See diagrams below and on the next page. For twin-wall polycarbonate panels, first drill a 1" hole through the twin-wall panel only at bracket mount position, then drill the 7/16" mounting hole through the end wall frame tube. This allows the mounting nuts and washers to directly contact end wall frame without crushing the twin-wall polycarbonate panels. See diagrams below and on the next page. Before you install track bracket, fill hole in polycarbonate panel using customer-supplied sealant.
ATTACH DOOR TRACK (continued)
2. Install the FAK26 rod as shown above.
3. Repeat to install and secure the remaining FAK26 threaded 3/8" rods.
Twin-Wall Polycarbonate End Wall Panel
Outside Building
FAME18B Flat WasherEnd Wall
Frame Tube
Inside Building
FALB04B Nut
FAME18B Flat Washer
FAMA38B Lock Washer
FAK26 Rod
FALB04B Nut
Corrugated Polycarbonate End Wall Panel
Outside Building
FAME18B Flat Washer
End Wall Frame Tube
Inside Building
FALB04B Nut
FAME18B Flat Washer
FAMA38B Lock Washer
FAK26 Rod
FALB04B Nut
NOTE: Fill hole in panel with customer-supplied silicone sealant after nut is tightened.
SIDE VIEW
SIDE VIEW
10 Revision date: 04.30.19
Sliding Door Track Assembly
4. Install the mounting brackets and door tracks. See diagrams below. NOTE: For polycarbonte panels, install as many FAME52B washers as needed to prevent the track brackets from touching the panel when installed, then secure with the nut, lock washer and flat washer. See diagrams below.
5. Position tracks as needed in brackets to allow doors to fully close and open when operated. See diagrams below.
ATTACH DOOR TRACK (continued)
6. Add FAME18B flat washer, FAMA38B lock washer, and FALB04B nut to each threaded rod. Tighten the nuts to secure mounting brackets to the frame. Cut the threaded rods to the desired length.
7. Continue with next procedure.
TOP VIEW SHOWING TRACK BRACKET
Track bracket with track installed.
Track bracket with track installed.
FAME52B Flat Washers
FAME52B Flat Washers
100380 Bracket
100380 Bracket
End Wall Frame Tube
End Wall Frame Tube
End Wall Frame Tube
End Wall Frame Tube
11Revision date: 04.30.19
Adjust Doors
Adjusting Locknut
Adjusting Locknut
INSTALL AND ADJUST SLIDING DOOR
Complete these steps:
1. With assistance, carefully lift doors into position and slide bearing hangers into the end of the door track.
2. Slide doors to the closed position.
3. Adjust the nuts on each bearing hanger to achieve the desired fit.
ATTENTION: Doors will hang level and close tightly—no gap where doors meet—when properly adjusted. Doors should glide freely through the stay rollers. Adjust as needed.
4. Tighten nuts to secure bearing hanger adjustment.
5. Loosen the stay rollers as needed to adjust later.
Door Jamb
End Frame Base Tube
Inside Building
Outside Building
Slid
ing
Doo
r Fra
me
Ground LevelAdjust and Tighten
NOTE: Allow clearance for door cladding, which is installed later. Actual positions of components may differ from diagram.
6. Continue with the next procedure.
Space below is reserved for customer notes.
Door panel installed later.
12 Revision date: 04.30.19
Twin-Wall Single Sliding Door AssemblyTWIN-WALL DOOR ASSEMBLY
If your door kit includes a corrugated polycarbonate panel, skip this section and continue with the assembly steps for that door. The materials and parts needed to assemble the door include:
• Assembled door frames with bearing hangers
• 8 mm panels (116049)
• Door handles (100362)
• Pancake head screws (115581)
• Neo-bonded washers (102921B)
• Aluminum profile (104213)
Assemble and Attach Doors
NOTE: Attach polycarbonate panel with UV-protected side toward the outside/sun.
1. Remove door frames with bearing hangers from door track and place on a flat surface.
2. Take polycarbonate panel and trim so length is one-quarter inch (1/4") shorter than length of door frame.
NOTE: Attach panel in locations shown in photo to hold in place while attaching aluminum profile to perimeter of panel.
6. Install aluminum U-channel profile to all edges of polycarbonate panel. The 104213 sections at top and bottom of panel run to panel edges to seal cells.
5. Using 115581 screws and galvanized neo-bonded washers, attach panel to horizontal cross tube of door frame. Evenly space Tek screws and washers every 12" or so.
3. Trim width of panel (if needed) so that it is one-quarter inch (1/4") narrower than width of door frame. NOTE: Trimming panel as instructed will keep panel flush with edges of the door frame once the aluminum profile (104213) is installed.
4. Center panel on a door frame.
Mark UV Side X
Install this edge to the underside of the panel against the door frame.
Photo shows the polycarbonate panel attached to the outside of the door frame and finished with the aluminum (104213) U-channel profile.
45° Angle
13Revision date: 04.30.19
Twin-Wall Single Sliding Door Assembly
TWIN-WALL DOOR ASSEMBLY (continued) 11. Install two Tek screws through the front of the door track at each end to prevent the doors from sliding out of the track.
12. Install door handles in the desired locations. Drive 115581 pancake head screws through the panel and into the door frame. Handles can be installed vertically or horizontally.
ATTENTION: The installation of the 104548 profile is an optional step for those who want to cap the end of the end panels at the door opening. Use Tek screws to secure the profile to the end wall framing. View is from the inside of the frame looking at the point where the door meets the door frame of the end wall.
14. Check the door operation and verify that doors slide smoothly in the door track. Adjust as needed.
15. Continue by reading the care and maintenance information.
Stay Roller
SIDE VIEW
Adjust Stay Roller as needed.
Door w/Panel Attached
Door Frame w/Panel Attached
Door Door Frame
115581 Screws
ATTENTION: Do not use an impact driver to install screws. Use a variable speed drill and the 100448 nut setter. Install screws at 16" on-center.
8. With assistants, lift door up and into place with the panel facing out and insert the rollers into the track.
9. Repeat the steps to attach polycarbonate panel to remaining door frame and slide it into the door track.
10. Slide doors to the closed position and adjust the stay roller for each door at bottom as needed and tighten.
7. Take the 115581 screws and, using the 100448 bit and drill driver, secure trim to door. Carefully install each screw. DO NOT OVERTIGHTEN! Doing so will dent the aluminum trim pieces.
Install Tek screws here.
13. Install the 104548 profile along the end wall door frame as shown in the following photos.
Stay Roller
Door w/Panel Attached
Door Opening
Slide to
Close
14 Revision date: 04.30.19
CORRUGATED DOOR ASSEMBLY
The materials and parts needed to assemble the door include:
• Door frame (102923) and corrugated panel (104620)
• Tek screws (FA4484B)
• Neo-bonded washers (102921B)
• Horizontal closure strip (104709)
Attach Panel to Door Frame
1. Take door frame with attached bearing hangers and place it on a flat surface.
2. Select one (1) corrugated panel—this will be one 50" x 8' 2" panel—and trim it so that the length is one-quarter inch (1/4") shorter than the length of the door frame. Pay attention of where the valleys of the panel end.
3. Install sections of the horizontal closure strips under the panel (see Detail A) and before attaching the panel to the horizontal cross tube. Trim one (1) closure strip as needed for each of the three (3) locations.
4. Install Tek screws and washers through the panel, closure strip, and into the horizontal cross tube every 6" or so. Always install Tek screws and washers in the valleys of the panel. Do not overtighten screws.
5. Attach the panel in the locations shown below to hold the panel in place.
6. Secure the sides of the polycarbonate panel to the door frame using Tek screws only every 16" (see Detail B).
Corrugated Panel
Valley
NOTE: Verify that the horizontal closure strip under the panel is in place before attaching the panel to the door frame.
Corrugated Single Sliding Door Assembly
DDEETTAAIILL AA
4488""
9922""DDEETTAAIILL AA
DDEETTAAIILL BB
DDEETTAAIILL BB
Closure Strip
Step 3
Closure Strip
Closure Strip
Closure Strip Tek Screw and Washer
ValleyDashed lines identify the positions of the foam closure strip (104709).
15Revision date: 04.30.19
Corrugated Single Sliding Door Assembly
CORRUGATED DOOR ASSEMBLY (continued)
9. After adjustments are made, slide door to its open position and install two Tek screws through the front of the door track at both ends to prevent the door from sliding out of the track.
Install the 104548 profile along the end wall door frame as shown in the following photos. ATTENTION: Installation of the 104548 profile is an optional step for those who want to cap the end of the corrugated end panels at the door opening. Use Tek screws to secure the profile to the end wall framing.
Photo above shows end wall without installed profile. Dashed line shows where to install profile to cover the valleys of corrugated end panels. View is from the inside of the frame looking at the point where the door meets the door frame of the end wall. See diagram below for top view. See page 13 for installed view.
Stay Roller
SIDE VIEW
Adjust Stay Roller as needed.
Door w/Panel Attached
Door Frame w/Panel Attached
Door
Door Frame
NOTE: Photo shows panels running horizontally. Actual frame will have vertically running panels. Photo is for illustration purposes.
10. Install the door handle in the desired location, using Tek screws through the panel and into the door frame.
11. Check the door operation and verify that door slides smoothly in the door track. Adjust as needed.
12. Continue by reading the care and maintenance information.
7. With assistants, lift door up and into place with the panel facing out and insert the hangers into the track.
8. Slide door to the closed position and adjust the stay roller as needed and tighten.
Step 9 Step 9
Stay Roller
Door w/Panel Attached
Door Jamb w/ End Panel Attached
Door Opening
Slide to
Close
Outside Inside
104548 Aluminum Profile
TOP VIEWSlide Door to Open
Doo
r Fra
me
Door Jamb
End Wall Horizontal Support
Cor
ruga
ted
Pane
l
Corrugated Panel – End Wall
16 Revision date: 04.30.19
Space below is reserved for customer notes.
Shelter Care and MaintenanceSHELTER CARE AND MAINTENANCE
Proper care and maintenance of the door are important. Check the following items periodically to properly maintain the door and door frame:
• Regularly check the polycarbonate panels to see that they remain secure and in good condition. Replace damaged panel if needed.
• Check connections and all fasteners to verify that they remain tight.
• Check the contents of the shelter to verify that nothing is touching the polycarbonate panels that could cause damage or interfere with the door operation.
• For safety, door must remain fully opened or fully closed. Do not leave door ajar.
• Check all slider mounting bolts regularly and tighten as needed.
• Replace damaged or broken parts immediately.
• Lubricate bearing hangers and stay rollers as needed to keep them operating smoothly.
• For replacement or missing parts, contact you sales representative for assistance.
17Revision date: 04.30.19
QUICK START GUIDE
Double Sliding Door Kit (GS05KDR2SLT and GS05KDR2SLC)
Quick Start Guide
Corrugated Door SampleGS05KDR2SLC
Finished Grade
Finished Grade
Finished Grade
Finished Grade
Twin-Wall Door SampleGS05KDR2SLT
ATTENTION: End frame and end rafter are not included with any door kit. Actual width of the building end wall may differ.
18 Revision date: 04.30.19
2'-0
"E
MB
ED
ME
NT
90"
R.O
.
VIEW
2
AN
GLE
BR
AC
KE
T
1.5"
X 1
.5" S
QU
AR
E T
UB
E C
ON
NE
CTI
ON
(S15
P020
)
DO
OR
JA
MB
TO
HE
AD
ER
CO
NN
EC
TIO
N
1.5"
X 1
.5" S
QU
AR
E T
UB
E (
VIEW
3
(CU
T TO
FIT
IF N
EE
DE
D)
1.5"
X 1
.5" S
QU
AR
E T
UB
E (S
15P1
18)
1.5"
X 1
.5" S
QU
AR
E T
UB
E (1
0289
710
2897
)
GR
OU
ND
LE
VE
L
AN
GLE
BR
AC
KE
T (Q
H13
30)
AN
GLE
BR
AC
KE
T (Q
H13
30)
AN
GLE
BR
AC
KE
T
(QH
1330
)
VIEW
1H
EA
DE
R T
O E
ND
WA
LL C
OLU
MN
CO
NN
EC
TIO
N
(QH
1330
)
)
1.5"
X 1
.5" S
QU
AR
E T
UB
E1.
5" X
1.5
" SQ
UA
RE
TU
BE
(S15
P020
)(C
UT
TO F
IT IF
NE
ED
ED
)
93"
R.O
.
Doo
r Fr
ame
Layo
ut
ATTE
NTI
ON
: Squ
are
the
door
ope
ning
an
d m
easu
re th
e do
or b
efor
e an
chor
ing
the
door
jam
bs in
con
cret
e.
19Revision date: 04.30.19
Doo
r Fr
ame
Det
ail C
onne
ctio
ns
DO
OR
HE
AD
ER
DO
OR
JA
MB
A
NG
LE B
RA
CK
ET
(QH
1330
)- (
4X) #
14 X
1" T
EK
SC
RE
W
VIEW
21.
5" X
1.5
" SQ
UA
RE
TU
BE
CO
NN
EC
TIO
NH
EA
DE
R T
O E
ND
WA
LL C
OLU
MN
CO
NN
EC
TIO
NVI
EW 1
VIEW
3D
OO
R J
AM
B T
O H
EA
DE
R C
ON
NE
CTI
ON
1.5"
X 1
.5" S
QU
AR
E T
UB
E
- (2X
) #14
X 1
" TE
K S
CR
EW
EN
DW
ALL
CO
LUM
N
DO
OR
HE
AD
ER
A
NG
LE B
RA
CK
ET
(QH
1330
)- (
4X) #
14 X
1" T
EK
SC
RE
W
ATTE
NTI
ON
: Ins
tall
scre
ws
in a
loca
tion
that
w
ill no
t int
erfe
re w
ith th
e in
stal
latio
n of
the
door
as
sem
bly.