7/30/2019 Ground Water Tank Model

1/16

DESIGN OF WATER TANK

DATA:

Size of tank : 6.0 x 6.0 x 6.0m

Concrete Mix: M25

Steel Grade: Tor Steel

Steps:

STEP 1 (Creation of Geometry):

New Project Select Space Length =meters; Force=KN;

File Name=Water tank Next

Select Add Plate Finish.

For Add Plate

Snap Node /Beam

Linear (Open) Radial (closed) Irregular (closed)

Plan Angle of Plan

X-Y X-X

X-Z Y-Y

Y-Z Z-Z

Grid origin (m)

X Y Z

0 0 0

7/30/2019 Ground Water Tank Model

2/16

Construction Lines

Left Right Spacing m Skew

X 0 4 1.5 0

Y 0 4 1.5 0

Click Snap Node/Beam then draw the following figure (Joint the points atclockwise direction)

7/30/2019 Ground Water Tank Model

3/16

Now click Translational Repeat

Global Direction

X Y Z

No. of steps 3

Default step spacing 1.50

Click Ok.Then it shows the following figure

7/30/2019 Ground Water Tank Model

4/16

Now click Translational Repeat

Global Direction

X Y Z

No. of steps 3

Default step spacing 1.50

Click Ok.Then it shows the following figure

7/30/2019 Ground Water Tank Model

5/16

Now, click Labels Symbols and Labels Plate Orientation (T) OkThen it shows the following figure

Then Click (Generate Rotate)Angle 90 degreesNode 1: (selecte point a)Node 2: (selecte point b)Generate Mode

CopyMove

Then it shows the following figure

7/30/2019 Ground Water Tank Model

6/16

Then click Generate Rotate

Angle -90 DegreeNode 1 : (select point x)

7/30/2019 Ground Water Tank Model

7/16

Node 2 : (select point y)Generate Mode

CopyMove

Then it shows the following figure

Now click Translational Repeat

Global Direction

X Y Z

No. of steps 1

Default step spacing 6.0m

Click Ok.

7/30/2019 Ground Water Tank Model

8/16

Then it shows the following figure

Then, Click view from +YThen it shows the following figure

7/30/2019 Ground Water Tank Model

9/16

All the Z axis should be in the Tank.For this reason, we removed the FG axis at 180 degrees.We need the following figure.

7/30/2019 Ground Water Tank Model

10/16

Then click Generate RotateAngle 180 DegreeNode 1 : (select point A)Node 2 : (select point A)Generate Mode

CopyMove

Then it shows the following figure

7/30/2019 Ground Water Tank Model

11/16

7/30/2019 Ground Water Tank Model

12/16

Then click Generate RotateAngle 90 DegreeNode 1 : (select point x)Node 2 : (select point y)Generate Mode

Copy

MoveThen it shows the following figure

7/30/2019 Ground Water Tank Model

13/16

Now, click Labels Symbols and Labels Plate Orientation (T) Ok

(For Remove Orientation) Ok.

Step 2: (Properties)

General Property Thickness (for plate) Material concrete

Node 1: 200Node 2: 200Node 3: 200

Node 4: 200 Select plate thickness CONCRETESelect whole

structure

Assign to selected plateAssign AddClose.Then it shows the following figure.

7/30/2019 Ground Water Tank Model

14/16

Step 3: (Support condtions)

Click General Support create Pinned add s2 support 2

Assign to selected Nodes close.After assigning, it shows the following figureb

7/30/2019 Ground Water Tank Model

15/16

7/30/2019 Ground Water Tank Model

16/16