AR-332™

Prism SightUsers Guide

The Burris AR-332 prism sight is a tough,yet compact ‘Close Quarters’ optic made fortactical carbines. With its 3x magnification andilluminated Ballistic CQ™ reticle, it providesquick target acquisition for close-in or fastmoving targets, but also features easy-to-usedrop-compensation for accurate shots out to600 yards. At 100 yards, the sight delivers agenerous field-of-view of 32 feet.

The AR-332 is waterproof, shockproof, andfogproof with fully multi-coated lensesfor brightness and clarity. Users have thechoice of three reticle presentations. Whennon-illuminated, the reticle is black, but inlighted modes the user has a choice of red orgreen with five power settings each. The sightincludes a sunshade, as well as flip-up lenscovers. For tactical versatility, it has three shortintegral Picatinny rails for accessories.

Specifications

WarrantyWe will repair or replace your Burris optic if it is damagedor defective. The warranty is automatically transferred tofuture owners.

• No repair or replacement charge• No warranty card needed• No receipt needed• No questions asked

Field of View ( in feet @ 100 yards) 32Eye Relief (inches) 2.5Close Focus (feet) 9Click Value in MOA 1/2 MOAMax Adjust in MOA 80Weight (Ounces) 16.6Height Above Rail (inches), to optic centerline 1.6Overall Length (inches) 5.30*Battery Life - High 200 hoursBattery Life - Medium 500 hours* without sunshade or flip-up covers

AR-332

Burris Company331 East 8th St., Greeley, CO 80631

(970) 356-1670BurrisOptics.com

Facebook.com/BurrisOpticsINSTR-1015

600

Reverts to black whenbattery is off

Green Setting

Red Setting

AR-332 user guide_Layout 1 8/7/15 11:27 AM Page 1

Battery Replacement The AR-332 is powered by a commonly availableCR2032 lithium battery that delivers 200 hours of lifeat the highest power settings, and approximately500 hours at medium settings. The batterycompartment is on the top of the sight, inside thereticle illumination selector knob. Choose a red orgreen power setting by aligning the number settingwith the white dot to the rear of the battery housing.

To open the compartment, simply hold theillumination selector knob to keep it from rotatingwhile you use a coin or other tool to turn the capcounter-clockwise. Drop in the replacement batterywith the positive side (+) face up, and re-tightencompletely. Note: The lid must be in place and sufficientlytight to maintain the waterproof capability ofthe AR-332.

Mounting the Optic

Picatinny Rail- The sight comes factory-ready tomount to a Picatinny rail system. Using a ½" wrench,loosen the nuts on the left side of the base to openthe mount just enough to fit over the width of therail. Once positioned on the rail, finger-tighten totest the position on the rail. The normal eye relief ofthe AR-332 is 2.5". Once properly located on the rail,use the wrench to tighten the base nuts to 65 in-lbs.For convenience, Burris offers an AR-QD Mount(#410349) for quick attachment to your gun andreturn-to-zero reliability. It fits any Picatinny baseand is ideal for mounting the AR-332 on flat-topplatforms.

Carry Handle - In order to mount to an AR carryhandle you must first remove the Picatinny RailMounting Bracket. This is attached to the sight bodyby two screws on the underside of the mount. Sincethese screws were installed using a medium-strength but non-permanent thread locker, they willbe harder than normal to remove. Once the sight is

free of the mount, locate the sight base in thehandle channel such that it will accept the thumb-screw provided with the sight and insert from below.Finger-tight is most often sufficient, but holes inthe knurled knob are provided to allow additionaltightening with a small rod.

Re-Attaching the Picatinny Rail Base - If you wishto re-install the Picatinny Base, be sure to use aremovable thread locker such as Loctite 242 whensecuring the Picatinny Base to the sight body. Thisprevents movement between the sight and themount.

Focus AdjustmentThe prism sight has a diopter adjustment ring on theocular end which is used to sharpen reticle focus toyour preference.

Sighting InWe recommend sighting in for 100 yards since theBallistic Drop Compensation is calculated for thatdistance. Click values are 1/2 MOA and the sight has80 total MOA of adjustment.

Be sure you have a safe location for sight in. Boresight using a commercial bore sighting tool; if you donot have a boresighting tool, follow this procedure.Place the weapon in a shooting rest with the bolt andcarrier removed, and the stock assembly anglingdown and out of your way. Align the reticle on thebullseye and then look down the bore to determinerough bullet placement. The AR-332 is designed withthe reticle centered in its range of movement, so ifthe bore aligns well off the bullseye and target, youshould check for a mounting problem. Re-assemblethe rifle and fire a few shots. Make corrections asnecessary using the adjustment knobs that havebullet-strike directional arrows. Continue until thesight is zeroed and then replace the adjustmentknob caps.

AR-332 user guide_Layout 1 8/7/15 11:27 AM Page 2