Graved Admit
-
Upload
jose-antonio-mieres-madrid -
Category
Documents
-
view
232 -
download
0
Transcript of Graved Admit
-
8/4/2019 Graved Admit
1/40
Chapter 2
The Earths Gravitational field
2.1 Global Gravity, Potentials, Figure of the Earth, Geoid
Introduction
Historically, gravity has played a central role in studies of dynamic processes in the Earths interior
and is also important in exploration geophysics. The concept of gravity is relatively simple, high-
precision measurements of the gravity field are inexpensive and quick, and spatial variations in the
gravitational acceleration give important information about the dynamical state of Earth. However,
the study of the gravity of Earth is not easy since many corrections have to be made to isolate
the small signal due to dynamic processes, and the underlying theory although perhaps more
elegant than, for instance, in seismology is complex. With respect to determining the three-
dimensional structure of the Earths interior, an additional disadvantage of gravity, indeed, of any
potential field, over seismic imaging is that there is larger ambiguity in locating the source of
gravitational anomalies, in particular in the radial direction.
In general the gravity signal has a complex origin: the acceleration due to gravity, denoted by
g , (g in vector notation) is influenced by topography, aspherical variation of density within the
Earth, and the Earths rotation. In geophysics, our task is to measure, characterize, and interpret
the gravity signal, and the reduction of gravity data is a very important aspect of this scientific
field. Gravity measurements are typically given with respect to a certain reference, which can but
does not have to be an equipotential surface. An important example of an equipotential surface is
the geoid (which itself represents deviations from a reference spheroid).
The Gravity Field
The law of gravitational attraction was formulated by Isaac Newton (1642-1727) and published in
1687, that is, about three generations after Galileo had determined the magnitude of the gravita-tional acceleration and Kepler had discovered his empirical laws describing the orbits of planets.
In fact, a strong argument for the validity of Newtons laws of motion and gravity was that they
could be used to derive Keplers laws.
For our purposes, gravity can be defined as the force exerted on a massm
due to the combination of
(1) the gravitational attraction of the Earth, with massM
orM
E
and (2) the rotation of the Earth.
The latter has two components: the centrifugal acceleration due to rotation with angular velocity
27
-
8/4/2019 Graved Admit
2/40
28 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
! and the existence of an equatorial bulge that results from the balance between self-gravitation
and rotation.
The gravitational force between any two particles with (point) massesM
at positionr
0
andm
at
positionr
separated by a distancer
is an attraction along a line joining the particles (see Figure
2.1):
F = k F k = G
M m
r
2
(2.1)
or, in vector form:
F = G
M m
k r r
0
k
3
( r r
0
) = G
M m
k r r
0
k
2
r
0
: (2.2)
Figure 2.1: Vector diagram showing the geometry of the gravitational attraction.
where r 0 is a unit vector in the direction of ( r r0
) . The minus sign accounts for the fact that the
force vector F points inward (i.e., towards M ) whereas the unit vector r 0 points outward (away
from M ). In the following we will place M at the origin of our coordinate system and take r0
at
O to simplify the equations (e.g., r r0
= r and the unit vector r 0 becomes r ) (see Figure 2.2).
Figure 2.2: Simplified coordinate system.
G
is the universal gravitational constant:G = 6 : 6 7 3 1 0
1 1 m3 kg 1 s 2 (or N m2 kg 2 ),
which has the same value for all pairs of particles.G
must not be confused withg
, the gravita-
tional acceleration, or force of a unit mass due to gravity, for which an expression can be obtained
by using Newtons law of motion. IfM
is the mass of Earth:
F = m a = m g = G
M m
r
2
r ) g =
F
m
= G
M
r
2
r
andg = k g k = G
M
r
2
:
(2.3)
The accelerationg
is the length of a vectorg
and is by definition always positive:g > 0
. We
define the vectorg
as the gravity field and take, by convention,g
positive towards the center of
the Earth, i.e., in the r
direction.
-
8/4/2019 Graved Admit
3/40
2.1. GLOBAL GRAVITY, POTENTIALS, FIGURE OF THE EARTH, GEOID 29
The gravitational acceleration g was first determined by Galileo; the magnitude of g varies over
the surface of Earth but a useful ball-park figure is g = 9.8 ms 2 (or just 10 ms 2 ) (in S.I.
Systeme International dUnites units). In his honor, the unit often used in gravimetry is the
Gal. 1 Gal = 1 cms 2 = 0.01 ms 2 10 3 g . Gravity anomalies are often expressed in milliGal,
i.e., 10 6 g or microGal, i.e., 10 9 g . This precision can be achieved by modern gravimeters. An
alternative unit is the gravity unit, 1 gu = 0.1 mGal = 10 7 g .
When G was determined by Cavendish in 1778 (with the Cavendish torsion balance) the mass of
the Earth could be determined and it was found that the Earths mean density, 5 5 0 0
kgm 3 ,
is much larger than the density of rocks at the Earths surface. This observations was one of the
first strong indications that density must increase substantially towards the center of the Earth. In
the decades following Cavendish measurement, many measurements were done ofg
at different
locations on Earth and the variation ofg
with latitude was soon established. In these early days
of geodesy one focused on planet wide structure; in the mid to late 1800s scientists started to
analyze deviations of the reference values, i.e. local and regional gravity anomalies.
Gravitational potential
By virtue of its position in the gravity fieldg
due to massM
, any massm
has gravitational po-tential energy. This energy can be regarded as the work
W
done on a massm
by the gravitational
force due toM
in movingm
fromr
r e f
tor
where one often takesr
r e f
= 1
. The gravitational
potentialU
is the potential energy in the field due toM
per unit mass. In other words, its the
work done by the gravitational force g per unit mass. (One can define U as either the positive or
negative of the work done which translates in a change of sign. Beware!). The potential is a scalar
field which is typically easier to handle than a vector field. And, as we will see below, from the
scalar potential we can readily derive the vector field anyway.
(The gravity field is a conservative field so just how the mass m is moved from rr e f
to r is not
relevant: the work done only depends on the initial and final position.) Following the definition
for potential as is common in physics, which considers Earth as a potential well i.e. negative
we get for U:
U =
Z
r
r
r e f
g d r =
Z
r
r
r e f
G M
r
2
r d r = G M
Z
r
1
1
r
2
d r =
G M
r
(2.4)
Note that r d r = d r because r and d r point in opposite directions.
Figure 2.3: By definition, the potential is zero at infinity and decreases towards the mass.
U
represents the gravitational potential at a distancer
from massM
. Notice that it is assumed that
U ( 1 ) = 0
(see Figure 2.3).
-
8/4/2019 Graved Admit
4/40
30 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
The potential is the integration over space (either a line, a surface or a volume) of the gravity field.
Vice versa, the gravity field, the gravity force per unit mass, is the spatial derivative (gradient) of
the potential.
g =
G M
r
2
r =
@
@ r
G M
r
=
@
@ r
U = g r a d U r U (2.5)
Intermezzo 2.1 THE GRADIENT OF THE GRAVITATIONAL POTENTIAL
We may easily see this in a more general way by expressingd r
(the incremental distance along the line
joining two point masses) into some set of coordinates, using the properties of the dot product and the
total derivative ofU
as follows (by our definition, moving in the same direction asg
accumulates negative
potential):
d U = g d r
= g
x
d x g
y
d y g
z
d z
(2.6)
By definition, the total derivative ofU
is given by:
d U
@ U
@ x
d x +
@ U
@ y
d y +
@ U
@ z
d z (2.7)
Therefore, the combination of Eq. 2.6 and Eq. 2.7 yields:
g =
@ U
@ x
@ U
@ y
@ U
@ z
= g r a d U r U
(2.8)
One can now see that the fact that the gravitational potential is defined to be negative means that
when massm
approaches the Earth, its potential (energy) decreases while its acceleration due to
attraction the Earths center increases. The slope of the curve is the (positive) value ofg
, and theminus sign makes sure that the gradient U points in the direction of decreasing r , i.e. towards
the center of mass. (The plus/minus convention is not unique. In the literature one often sees
U = G M = r and g = r U .)
Some general properties:
The gradient of a scalar fieldU
is a vector that determines the rate and direction of change
inU
. Let an equipotential surfaceS
be the surface of constantU
andr
1
andr
2
be positions
on that surface (i.e., with U1
= U
2
= U ). Then, the component of g along S is given by
( U
2
U
1
) = ( r
1
r
2
) = 0 . Thus g = r U has no components along S : the field is
perpendicular to the equipotential surface. This is always the case, as derived in Intermezzo
2.2.
Since fluids cannot sustain shear stress the shear modulus = 0
, the forces acting on the
fluid surface have to be perpendicular to this surface in steady state, since any component
of a force along the surface of the fluid would result in flow until this component vanishes.
The restoring forces are given byF = m r U
as in Figure 2.4; a fluid surface assumes an
equipotential surface.
-
8/4/2019 Graved Admit
5/40
2.1. GLOBAL GRAVITY, POTENTIALS, FIGURE OF THE EARTH, GEOID 31
Figure 2.4: F = m r U provides the restoring
force that levels the sea surface along an equipoten-tial surface.
For a spherically symmetric Earth the equipotential would be a sphere andg
would point
towards the center of the sphere. (Even in the presence of aspherical structure and rotation
this is a very good approximation of g . However, if the equipotential is an ellipsoid, g =
r U does not point to r = 0 ; this lies at the origin of the definition of geographic and
geocentric latitudes.)
Using gravity potentials, one can easily prove that the gravitational acceleration of a spheri-
cally symmetric mass distribution, at a point outside the mass, is the same as the acceleration
obtained by concentrating all mass at the center of the sphere, i.e., a point mass.
This seems trivial, but for the use of potential fields to study Earths structure it has several
important implications:
1. Within a spherically symmetric body, the potential, and thus the gravitational accel-
eration g is determined only by the mass between the observation point at r and the
center of mass. In spherical coordinates:
g ( r ) = 4
G
r
2
r
Z
0
( r
0
) r
0 2
d r
0 (2.9)
This is important in the understanding of the variation of the gravity field as a function
of radius within the Earth;
2. The gravitational potential by itself does not carry information about the radial dis-
tribution of the mass. We will encounter this later when we discuss more properties
of potentials, the solutions of the Laplace and Poisson equations, and the problem ofnon-uniqueness in gravity interpretations.
3. if there are lateral variations in gravitational acceleration on the surface of the sphere,
i.e. if the equipotential is not a sphere there must be aspherical structure (departure
from spherical geometry; can be in the shape of the body as well as internal distribution
of density anomalies).
-
8/4/2019 Graved Admit
6/40
32 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
Intermezzo 2.2 GEOMETRIC INTERPRETATION OF THE GRADIENT
Let C be a curve with parametric representation C ( ) , a vector function. Let U be a scalar function of
multiple variables. The variation ofU
, confined to the curveC
, is given by:
d
d t
U ( C ( t ) ) ] = r U ( C ( t ) )
d C ( )
d t
(2.10)
Therefore, if C is a curve of constant U ,d
d t
U ( C ( ) ) ] will be zero.Now let C ( ) be a straight line in space:
C ( ) = p + a t (2.11)
then, according to the chain rule (2.10), att
0
= 0
:
d
d t
U ( C ( ) ) ]
t = t
0
= r U ( p ) a
(2.12)
It is usefule to define the directional derivative ofU
in the direction ofa
at pointp
as:
D
A
U ( p ) = r U ( p )
a
k a k
(2.13)
From this relation we infer that the gradient vector r U ( p ) at p gives the direction in which the change
ofU
is maximum. Now letS
be an equipotential surface, i.e. the surface of constantU
. Define a set of
curves Ci
( ) on this surface S . Clearly,
d
d t
U ( C
i
( ) ) ]
t = t
0
= r U ( p )
d C
i
d t
( t
0
) = 0 (2.14)
for each of those curves. Since the Ci
( ) lie completely on the surface S , the d C id t
( t
0
) will define a plane
tangent to the surface S at point p . Therefore, the gradient vector r U is perpendicular to the surface S of
constant U . Or: the field is perpendicular to the equipotential surface.
In global gravity one aims to determine and explain deviations from the equipotential surfaces, or
more precisely the difference (height) between equipotential surfaces. This difference in height is
related to the localg
. In practice one defines anomalies relative to reference surfaces. Important
surfaces are:
Geoid the actual equipotential surface that coincides with the average sea level (ignoring tides
and other dynamical effects in oceans)
(Reference) spheroid : empirical, longitude independent (i.e., zonal) shape of the sea level with
a smooth variation in latitude that best fits the geoid (or the observed gravity data). This
forms the basis of the international gravity formula that prescribes g as a function of latitude
that forms the reference value for the reduction of gravity data.
Hydrostatic Figure of Shape of Earth : theoretical shape of the Earth if we know density androtation
!
(ellipsoid of revolution).
We will now derive the shape of the reference spheroid; this concept is very important for geodesy
since it underlies the definition of the International Gravity Formula. Also, it introduces (zonal,
i.e. longitude independent) spherical harmonics in a natural way.
-
8/4/2019 Graved Admit
7/40
2.2. GRAVITATIONAL POTENTIAL DUE TO NEARLY SPHERICAL BODY 33
2.2 Gravitational potential due to nearly spherical body
How can we determine the shape of the reference spheroid? The flattening of the earth was already
discovered and quantified by the end of the 18th century. It was noticed that the distance between
a degree of latitude as measured, for instance with a sextant, differs from that expected from a
sphere: RE
(
1
2
) 6= R
E
d , with RE
the radius of the Earth, 1
and 2
two different latitudes
(see Figure 2.5).
Figure 2.5: Ellipticity of the Earth measured by the
distance between latitudes of the Earth and a sphere.
In 1743, Clairaut1 showed that the reference spheroid can also be computed directly from the
measured gravity fieldg
. The derivation is based on the computation of a potentialU ( P )
at point
P due to a nearly spherical body, and it is only valid for points outside (or, in the limit, on the
surface of) the body.
Figure 2.6: The potential U of the aspherical body is calcu-
lated at point P , which is external to the mass M =R
d M ;
O P = r , the distance from the observation point to the
center of mass. Note thatr
is constant and thats
,q
, and
are the variables. There is no rotation soU ( P )
represents
the gravitational potential.
The contribution d U to the gravitational potential at P due to a mass element d M at distance q
from P is given by
d U =
G
q
d M (2.15)
Typically, the potential is expanded in a series. This can be done in two ways, which lead to the
same results. One can write U ( P ) directly in terms of the known solutions of Laplaces equation
1In his book, Theorie de la Figure de la Terre.
-
8/4/2019 Graved Admit
8/40
34 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
(r 2 U = 0 ), which are spherical harmonics. Alternatively, one can expand the term 1 = q and
integrate the resulting series term by term. Here, we will do the latter because it gives better
understanding of the physical meaning of the terms, but we will show how these terms are, in
fact, directly related to (zonal) spherical harmonics. A formal treatment of solutions of spherical
harmonics as solutions of Laplaces equation follows later. The derivation discussed here leads to
what is known as MacCullaghs formula2 and shows how the gravity measurements themselves
are used to define the reference spheroid. Using Figure 2.6 and the law of cosines we can write
q
2
= r
2
+ s
2
2 r s c o s
so that
d U =
G
r
h
1 +
s
r
2
2
s
r
c o s
i
1
2
d M (2.16)
We can use the Binomial Theorem to expand this expression into a power series of( s = r )
.
Intermezzo 2.3 BINOMIAL THEOREM
( a + b )
n
= a
n
+ n a
n 1
b +
1
2 !
n ( n 1 ) a
n 2
b
2
+
1
3 !
n ( n 1 ) ( n 2 ) a
n 3
b
3
+
(2.17)
for j ba
j
-
8/4/2019 Graved Admit
9/40
2.2. GRAVITATIONAL POTENTIAL DUE TO NEARLY SPHERICAL BODY 35
Intermezzo 2.4 EQUIVALENCE WITH (ZONAL) SPHERICAL HARMONICS
Note that equation (2.19) is, in fact, a power series of ( s = r ) , with the multiplicative factors functions of
c o s ( )
:
U ( P ) =
G
r
Z
1
s
r
0
+ c o s
s
r
1
+
3
2
c o s
2
1
2
s
r
2
d M
=
G
r
Z
2
X
l = 0
P
l
( c o s )
s
r
l
d M (2.20)
In spectral analysis there are special names for the factorsP
l
multiplying( s = r )
l and these are known as
Legendre polynomials, which define the zonal surface spherical harmonicsa.
We will discuss spherical harmonics in detail later but here it is useful to point out the similarity between the
above expression of the potentialU ( P )
as a power series of( s = r )
andc o s
and the lower order spherical-
harmonics. Legendre polynomials are defined as
P
l
( ) =
1
2
l
l !
d
l
(
2
1 )
l
d
l
(2.21)
with some function. In our case we take = c o s so that the superposition of the Legendre polynomials
describes the variation of the potential with latitude. At this stage we ignore variations with longitude.Surface spherical harmonics that depend on latitude only are known as zonal spherical harmonics. For
l = 0 1 2 we get for Pl
P
0
( c o s ) = 1
(2.22)
P
1
( c o s ) = c o s (2.23)
P
2
( c o s ) =
3
2
c o s
2
1
2
(2.24)
which are the same as the terms derived by application of the binomial theorem.
The equivalence between the potential expression in spherical harmonics and the one that we are deriving by
expanding 1 = q is no coincidence: the potential U satisfies Laplaces equation and in a spherical coordinate
system spherical harmonics are the general solutions of Laplaces equation.
aSurface spherical harmonics are at the surface of a sphere what a Fourier series is to a time series; it can
be thought of as a 2D Fourier series which can be used to represent any quantity at the surface of a sphere
(geoid, temperature, seismic wave speed).
Let us rewrite eq. (2.19) by using the identity c o s 2 + s i n 2 = 1 :
U ( P ) =
G
r
Z
d M
G
r
2
Z
s c o s d M
G
r
3
Z
s
2
d M +
3
2
G
r
3
Z
s
2
s i n
2
d M (2.25)
We can get insight in the physics if we look at each term of eq. (2.25) separately:
1. G
r
R
d M =
G M
r is essentially the potential of a point mass M at O . This term willdominate for large
r
; at a large distance the potential due to an aspherical density distribution
is close to that of a spherical body (i.e., a point mass in O).
2.R
s c o s d M
represents a torque of mass
distance, which also underlies the definition of
the center of massr
c m
=
R
r d M =
R
d M
. In our case, we have chosenO
as the center of
mass andr
c m
= 0
with respect toO
. Another way to see that this integral must vanish is to
-
8/4/2019 Graved Admit
10/40
36 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
realize that the integration over d M is essentially an integration over between 0 and 2
and that c o s = c o s ( 2
) . Integration over takes s c o s back and forth over the line
between O and P (within the body) with equal contributions from each side of O , since O
is the center of mass.
3.
R
s
2
d M
represents the torque of a distance squared and a mass, which underlies the def-inition of the moment of inertia (recall that for a homogeneous sphere with radius R
and mass M the moment of inertia is 0.4 MR2 ). The moment of inertia is defined as
I =
R
r
2
d M . When talking about moments of inertia one must identify the axis of ro-
tation. We can understand the meaning of the third integral by introducing a coordinate
system x y z so that s = ( x y z ) , s 2 = x 2 + y 2 + z 2 so thatR
s
2
d M =
R
( x
2
+ y
2
+
z
2
) d M = 1 = 2
R
( y
2
+ z
2
) d M +
R
( x
2
+ z
2
) d M +
R
( x
2
+ y
2
) d M ]
and by realizing thatR
( y
2
+ z
2
) d M
R
( x
2
+ z
2
) d M
andR
( x
2
+ y
2
) d M
are the moments of inertia around the
x
-,y
-, andz
-axis respectively. See Intermezzo 2.5 for more on moments of inertia.
With the moments of inertia defined as in the box we can rewrite the third term in the
potential equation
G
r
3
Z
s
2
d M =
G
2 r
3
( A + B + C ) (2.26)
4.R
s
2
s i n
2
d M
. Here,s s i n
projectss
on a plane perpendicular toO P
and this integral thus
represents the moment of inertia of the body aroundO P
. This moment is often denoted by
I
.
Eq. (2.25) can then be rewritten as
U ( P ) =
G M
r
G
2 r
3
( A + B + C 3 I ) (2.27)
which is known as MacCullaghs formula.
At face value this seems to be the result of a straightforward and rather boring derivation, but it
does reveal some interesting and important properties of the potential and the related field. Equa-
tion (2.25) basically shows that in absence of rotation the gravitational attraction of an irregular
body has two contributions; the first is the attraction of a point mass located at the center of grav-
ity, the second term depends on the moments of inertia around the principal axes, which in turn
depend completely on the shape of the body, or, more precisely, on the deviations of the shape
from a perfect sphere. This second term decays as1 = r
3
so that at large distances the potentialapproaches that of a point mass M and becomes less and less sensitive to aspherical variations
in the shape of the body. This simply implies that if youre interested in small scale deviations
from spherical symmetry you should not be to far away from the surface: i.e. its better to use
data from satellites with a relatively low orbit. This phenomenon is in fact an example of up (or
down)ward continuation, which we will discuss more quantitatively formally when introducing
spherical harmonics.
-
8/4/2019 Graved Admit
11/40
2.2. GRAVITATIONAL POTENTIAL DUE TO NEARLY SPHERICAL BODY 37
Intermezzo 2.5 MOMENTS AND PRODUCTS OF INERTIA
A moment of inertia of a rigid body is defined with respect to a certain axis of rotation.
For discrete masses: I = m1
r
2
1
+ m
2
r
2
2
+ m
3
r
2
3
+ =
P
m
i
r
2
i
and for a continuum: I =R
r
2
d M
The moment of inertia is a tensor quantity
M I =
Z
r
2
( I ^ r ^ r
T
) d M (2.28)
Note: we revert to matrix notation and manipulation of tensors. I is a second-order tensor.
( I ^ r ^ r
T
)
is a projection operator: for instance,( I ^ z ^ z
T
) a
projects the vectora
on the (x
,y
) plane, i.e.,
perpendicular to z . This is very useful in the general expression for the moments of inertia around different
axis.
I =
1 0 0
0 1 0
0 0 1
!
and r2
I =
x
2
+ y
2
+ z
2
0 0
0 x
2
+ y
2
+ z
2
0
0 0 x
2
+ y
2
+ z
2
!
(2.29)
andr
2
^ r ^ r
T
= r r r r
T
= r r
T
=
x
y
z
!
x y z
=
x
2
x y x z
y x y
2
y z
z x z y z
2
!
(2.30)
So that:
r
2
( I ^ r ^ r
T
) =
y
2
+ z
2
x y x z
y x x
2
+ z
2
y z
z x z y x
2
+ y
2
!
(2.31)
The diagonal elements are the familiar moments of inertia around thex
,y
, andz
axis. (The off-diagonal
elements are known as the products of inertia, which vanish when we choose x , y , and z as the principal
axes.)Moment of Inertia around
x
-axis
aroundy
-axis
around z -axis
I
x x
=
R
( y
2
+ z
2
) d M = A
I
y y
=
R
( x
2
+ z
2
) d M = B
I
z z
=
R
( x
2
+ y
2
) d M = C
We can pursue the development further by realizing that the moment of inertiaI
around any general
axis (hereO P
) can be expressed as a linear combination of the moments of inertia around the
principal axes. Letl
2 ,m
2 , andn
2 be the squares of the cosines of the angle of the lineO P
with
thex
-,y
-, andz
-axis, respectively. Withl
2
+ m
2
+ n
2
= 1
we can writeI = l
2
A + m
2
B + n
2
C
(see Figure 2.7).
So far we have not been specific about the shape of the body, but for the Earth it is relevant to
consider rotational geometry so that A = B 6= C . This leads to:
I = A + ( C A ) n
2 (2.32)
Here, n = c o s with the angle between O P and the z -axis, that is is the co-latitude. ( =
9 0 , where is the latitude).
I = A + ( C A ) c o s
2
(2.33)
-
8/4/2019 Graved Admit
12/40
38 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
Figure 2.7: Definition of direction cosines.
and
U ( P ) =
G M
r
+
G
r
3
( C A )
3
2
c o s
2
1
2
(2.34)
It is customary to write the difference in moments of inertia as a fraction J2
of M a 2 , with a the
Earths radius at the equator.
C A = J
2
M a
2 (2.35)
so that
U ( P ) =
G M
r
+
G J
2
M a
2
r
3
3
2
c o s
2
1
2
(2.36)
J
2
is a measure of ellipticity; for a sphereC = A
,J
2
= 0
, and the potentialU ( P )
reduces to the
expression of the gravitational potential of a body with spherical symmetry.
Intermezzo 2.6 ELLIPTICITY TERMS
Lets briefly return to the equivalence with the spherical harmonic expansion. If we take = c o s
(see
box) we can write for U ( P )
U ( P ) = U ( r ) =
G M
r
J
0
P
0
( c o s ) + J
1
a
r
P
1
( c o s ) + J
2
a
r
2
P
2
( c o s )
(2.37)
The expressions (2.25), rewritten as (2.36), and (2.37) are identical if we define the scaling factorsJ
l
as
follows. Since P0
( c o s ) = 1 , J0
must be 1 because G M = r is the far field term; J1
= 0 if the coordinate
origin coincides with the center of mass (see above); andJ
2
is as defined above. This term is of particular
interest since it describes the oblate shape of the geoid. (The higher order terms (J
4
,J
6
etc.) are smaller by
a factor of order 1000 and are not carried through here, but they are incorporated in the calculation of the
reference spheroid.)
The final step towards calculating the reference gravity field is to add a rotational potential.
Let! = ! z
be the angular velocity of rotation around thez
-axis. The choice of reference frame
is important to get the plus and minus signs right. A particle that moves with the rotating earth is
influenced by a centripetal forceF
c p
= m a
, which can formally be written in terms of the cross
products between the angular velocity!
and the position vector asm ! ( ! s )
. This shows that
-
8/4/2019 Graved Admit
13/40
2.2. GRAVITATIONAL POTENTIAL DUE TO NEARLY SPHERICAL BODY 39
the centripetal acceleration points to the rotation axis. The magnitude of the force per unit mass
is s ! 2 = r ! 2 c o s . The source of Fc p
is, in fact, the gravitational attraction g (ge
+ F
c p
= g ).
The effective gravity ge
= g F
c p
(see Figure 2.8). Since we are mainly interested in the radial
component (the tangential component is very small we can write ge
= g r !
2
c o s
2
.
Figure 2.8: The gravitational attraction delivers the centripetal force needed to sustain the rotation
of the Earth.
In terms of potentials, the rotational potential has to be added to the gravitational potentialU
g r a v i t y
=
U
g r a v i t a t i o n
+ U
r o t
, with
U
r o t
=
Z
r !
2
c o s
2
d r =
1
2
r
2
!
2
c o s
2
=
1
2
r
2
!
2
s i n
2
(2.38)
(which is in fact exactly the rotational kinetic energy ( K = 12
I !
2
=
1
2
m r
2
!
2 ) per unit mass of a
rigid body 12
!
2
r
2
=
1
2
v
2 , even though we used an approximation by ignoring the component
of ge
in the direction of varying latitude d . Why? Hint: use the above diagram and consider the
symmetry of the problem)
The geopotential can now be written as
U ( r ) =
G M
r
+
G
r
3
J
2
M a
2
3
2
c o s
2
1
2
1
2
r
2
!
2
s i n
2
(2.39)
which describes the contribution to the potential due to the central mass, the oblate shape of the
Earth (i.e. flattening due to rotation), and the rotation itself.
We can also write the geopotential in terms of the latitude by substituting (s i n = c o s
):
U ( r ) =
G M
r
+
G
r
3
( C A )
3
2
s i n
2
1
2
1
2
r
2
!
2
c o s
2
(2.40)
We now want to use this result to find an expression for the gravity potential and acceleration at the
surface of the (reference) spheroid. The flattening is determined from the geopotential by defining
the equipotential U0
, the surface of constant U .
Since U0
is an equipotential, U must be the same ( U0
) for a point at the pole and at the equator.
We take c for the polar radius and a for the equatorial radius and write:
U
0 p o l e
= U ( c 9 0 ) = U
0 e q u a t o r
= U ( a 0 )
(2.41)
U
p o l e
=
G M
c
+
G
c
3
J
2
M a
2 (2.42)
-
8/4/2019 Graved Admit
14/40
40 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
U
e q u a t o r
=
G M
a
G
2 a
3
J
2
M a
2
1
2
a
2
!
2 (2.43)
(2.44)
and after some reordering to isolate a and c we get
f
a c
a
3
2
J
2
M a
2
M a
2
!
+
1
2
a !
2
G M = a
2
=
3
2
J
2
+
1
2
m (2.45)
Which basically shows that the geometrical flattening f as defined by the relative difference be-
tween the polar and equatorial radius is related to the ellipticity coefficient J2
and the ratio m
between the rotational (a ! 2 ) to the gravitational ( G M a 2 ) component of gravity at the equator.
The value for the flatteningf
can be accurately determined from orbital data; in fact within a year
after the launch of the first artificial satellite by the soviets this value could be determined
with much more accuracy than by estimates given by many investigators in the preceding cen-
turies. The geometrical flattening is small (f = 1 = 2 9 8 : 2 5 7 1 = 3 0 0
) (but larger than expected
from equilibrium flattening of a rotating body). The difference between the polar and equatorial
radii is thus aboutR
E
f = 6 3 7 1
km= 3 0 0 2 1
km.
In order to get the shape of the reference geoid (or spheroid) one can use the assumption that thedeviation from a sphere is small, and we can thus assume the vector from the Earths center to a
point at the reference geoid to be of the form
r
g
r
0
+ d r = r
0
( 1 + ) or, with r0
= a , rg
a ( 1 + ) (2.46)
It can be shown that can be written as a function of f and latitude as given by: rg
a ( 1
f s i n
2
) and (from binomial expansion) r 2g
a
2
( 1 + 2 f s i n
2
) .
Geoid anomalies, i.e. the geoid highs and lows that people talk about are deviations from
the reference geoid and they are typically of the order of several tens of meters (with a maximum
(absolute) value of about 100 m near India), which is small (often less than 0.5%) compared to the
latitude dependence of the radius (see above). So the reference geoid withr = r
g
according to
(2.46) does a pretty good job in representing the average geoid.
Finally, we can determine the gravity field at the reference geoid with a shape as defined by (2.46)
calculating the gradient of eqn. (2.40) and substituting the position rg
defined by (2.46).
In spherical coordinates:
g = r U =
@ U
@ r
1
r
@ U
@
(2.47)
g = j g j =
(
@ U
@ r
2
+
1
r
@ U
@
2
)
1
2
@ U
@ r
(2.48)
because 1r
@ U
@
is small.
So we can approximate the magnitude of the gravity field by:
g =
G M
r
2
3
G J
2
M a
2
r
4
3
2
s i n
2
1
2
r !
2
c o s
2
(2.49)
and, withr = r
g
= a
1 f s i n
2
-
8/4/2019 Graved Admit
15/40
2.2. GRAVITATIONAL POTENTIAL DUE TO NEARLY SPHERICAL BODY 41
g =
G M
a
2
( 1 f s i n
2
)
2
3 G J
2
M a
2
a
4
( 1 f s i n
2
)
4
3
2
s i n
2
1
2
a !
2
( 1 f s i n
2
) c o s
2
(2.50)
or, with the binomial expansion given above (2.46)
g ( ) =
G M
a
2
( 1 + 2 f s i n
2
) 3 J
2
3
2
s i n
2
1
2
m ( 1 s i n
2
)
=
G M
a
2
( 1 +
3
2
J
2
m ) +
2 f
9
2
J
2
+ m
s i n
2
=
G M
a
2
( 1 +
3
2
J
2
m )
1 +
2 f ( 9 = 2 ) J
2
+ m
1 + ( 3 = 2 ) J
2
m
s i n
2
=
G M
a
2
( 1 +
3
2
J
2
m )
n
1 + f
0
s i n
2
o
(2.51)
Eqn. (2.51) shows that the gravity field at the reference spheroid can be expressed as some latitude-
dependent factor times the gravity acceleration at the equator:
g
e q
( = 0 ) =
G M
a
2
1 +
3
2
J
2
m
(2.52)
Information about the flattening can be derived directly from the relative change in gravity from
the pole to the equator.
g
p o l e
= g
e q
( 1 + f
0
) ! f
0
=
g
p o l e
g
e q
g
e q
(2.53)
Eq. 2.53 is called Clairauts theorem3. The above quadratic equation for the gravity as a function
of latitude (2.51) forms the basis for the international gravity formula. However, this international
reference for the reduction of gravity data is based on a derivation that includes some of the higherorder terms. A typical form is
g = g
e q
( 1 + s i n 2 + s i n
2
2 )
(2.54)
with the factor of proportionality
and
depending onG M
,!
,a
, andf
. The values of these
parameters are being determined more and more accurate by the increasing amounts of satellite
data and as a result the international gravity formula is updated regularly. The above expression
(2.54) is also a truncated series. A closed form expression for the gravity as function of latitude is
given by the Somigliana Equation4
g ( ) = g
e q
(
1 + k s i n
2
p
1 e
2
s i n
2
)
:
(2.55)
This expression has now been adopted by the Geodetic Reference System and forms the basis forthe reduction of gravity data to the reference geoid (or reference spheroid). g
e q
= 9 : 7 8 0 3 2 6 7 7 1 4
ms 2 ;k = 0 : 0 0 1 9 3 1 8 5 1 3 8 6 3 9
;e = 0 : 0 0 6 6 9 4 3 7 9 9 9 0 1 3
.
3After Alexis Claude Clairaut (17131765).4After C. Somigliana.
-
8/4/2019 Graved Admit
16/40
42 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
2.3 The Poisson and Laplace equations
The gravitational field of the Earth is caused by its density. The mass distribution of the planet
is inherently three-dimensional, but we mortals will always only scratch at the surface. The most
we can do is measure the gravitational acceleration at the Earths surface. However, thanks to
a fundamental relationship known as Gausss Theorem5, the link between a surface observable
and the properties of the whole body in question can be found. Gausss theorem is one of aclass of theorems in vector analysis that relates integrals of different types (line, surface, volume
integrals). Stokess, Greens and Gausss theorem are fundamental in the study of potential fields.
The particularly useful theorem due to Gauss relates the integral over the volume of some property
(most generally, a tensorT
) to a surface integral. It is also called the divergence theorem. LetV
be a volume bounded by the surfaceS = @ V
(see Figure 2.9). A differential patch of surfaced S
can be represented by an outwardly pointing vector with a length corresponding to the area of the
surface element. In terms of a unit normal vector, it is given by n k j d S k j .
Figure 2.9: Surface en-
closing a volume. Unit
normal vector.
Gausss theorem (for generic stuff T ) is as follows:
Z
V
r T d V =
Z
@ V
n T d S : (2.56)
Lets see what we can infer about the gravitational potential within the Earth using only informa-
tion obtained at the surface. Remember we had
g =
G M
r
2
and g = r U : (2.57)
Suppose we measure g everywhere at the surface, and sum the results. What we get is the flux of
the gravity field
Z
@ V
g d S : (2.58)
At this point, we can already predict that if S is the surface enclosing the Earth, the flux of thegravity field should be different from zero, and furthermore, that it should have something to do
with the density distribution within the planet. Why? Because the gravitational field lines all point
towards the center of mass. If the flux was zero, the field would be said to be solenoidal . Unlike
the magnetic field the gravity field is essentially a monopole. For the magnetic field, field lines
5After Carl-Friedrich Gauss (17771855).
-
8/4/2019 Graved Admit
17/40
2.3. THE POISSON AND LAPLACE EQUATIONS 43
both leave and enter the spherical surface because the Earth has a positive and a negative pole. The
gravitational field is only solenoidal in regions not occupied by mass.
Anyway, well start working with Eq. 2.58 and see what we come up with. On the one hand (we
use Eq. 2.56 and Eq. 2.57),
Z
@ V
g n d S =
Z
V
r g d V =
Z
V
r r U d V =
Z
V
r
2
U d V :
(2.59)
On the other hand6 (we use the definition of the dot product and Eq. 2.57):
Z
@ V
g n d S =
Z
@ V
g
n
d S = 4 r
2
G M
r
2
= 4 G
Z
V
d V :
(2.60)
Weve assumed thatS
is a spherical surface, but the derivation will work for any surface. Equating
Eq. 2.59 and 2.60, we can state that
r
2
U ( r ) = 4 G ( r ) Poissons Equation (2.61)
and in the homogeneous case
r
2
U ( r ) = 0 Laplaces Equation (2.62)
The interpretation in terms of sources and sinks of the potential fields and its relation with the field
lines is summarized in Figure 2.10:
Figure 2.10: Poissons and Laplaces equations.
Poissons equation is a fundamental result. It implies
1. that the total mass of a body (say, Earth) can be determined from measurements of r U =
g
at the surface (see Eq. 2.60)
2. no information is required about how exactly the density is distributed withinV
, and
3. that if there is no potential source (or sink) enclosed by S Laplaces equation should be
applied to find the potential at a point P outside the surface S that contains all attracting
mass, for instance the potential at the location of a satellite. But in the limit, it is also valid
at the Earths surface. Similarly, we will see that we can use Laplaces equation to describe
Earths magnetic field as long as we are outside the region that contains the source for the
magnetic potential (i.e., Earths core).
6Note that the identity r 2 U = r r U is true for scalar fields, but for a vector field V we should have written
r
2
V = r ( r V ) r ( r V )
.
-
8/4/2019 Graved Admit
18/40
44 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
We often have to find a solution for U of Laplaces equation when only the value of U , or its
derivatives j r U j = g are known at the surface of a sphere. For instance if one wants to determine
the internal mass distribution of the Earth from gravity data. Laplaces equation is easier to solve
than Poissons equation. In practice one can usually (re)define the problem in such a way that one
can use Laplaces equation by integrating over contributions from small volumes d V (containing
the source of the potential d U , i.e., mass d M ), see Figure 2.11 or by using Newtons Law of
Gravity along with Laplaces equation in an iterative way.
Figure 2.11: Applicability of Poissons and Laplaces equations.
See Intermezzo 2.7.
Intermezzo 2.7 NON -UNIQUENESS
One can prove that the solution of Laplaces equation can be uniquely determined if the boundary conditions
are known (i.e. if data coverage at the surface is good); in other words, if there are two solutions U1
and
U
2
that satisfy the boundary conditions,U
1
andU
2
can be shown to be identical. The good news here is
that once you find a solution forU
ofr
2
U = 0
that satisfies the BCs you do not have to be concerned
about the generality of the solution. The bad news is (see also point (2) above) that the solution of Laplaces
equation does not constrain the variations of density withinV
. This leads to a fundamental non-uniqueness
which is typical for potentials of force fields. We have seen this before: the potential at a point P outside a
spherically symmetric body with total massM
is the same as the potential of a point massM
located in the
center O . In between O and P the density in the spherical shells can be distributed in an infinite number of
different ways, but the potential atP
remains the same.
2.4 Cartesian and spherical coordinate systems
In Cartesian coordinates we write for r 2 (the Laplacian)
r
2
=
@
2
@ x
2
+
@
2
@ y
2
+
@
2
@ z
2
: (2.63)
For the Earth, it is advantageous to use spherical coordinates. These are defined as follows (see
Figure 2.12):
8
>
:
x = r s i n c o s '
y = r s i n s i n '
z = r c o s
(2.64)
where = 0 !
= co-latitude,' = 0 ! 2
= longitude.
-
8/4/2019 Graved Admit
19/40
2.5. SPHERICAL HARMONICS 45
Figure 2.12: Definition of r ,
and'
in the spherical coordinate
system.
It is very important to realize that, whereas the Cartesian frame is described by the immobile unit
vectors x , y and z , the unit vectors r , and ' are dependent on the position of the point. They
are local axes. At pointP
,r
points in the direction of increasing radius from the origin,
in the
direction of increasing colatitude
and'
in the direction of increasing longitude'
.
One can go between coordinate axes by the transformation
0
B
@
r
'
1
C
A
=
0
B
@
s i n c o s ' s i n s i n ' c o s
c o s c o s ' c o s s i n ' s i n
s i n ' c o s ' 0
1
C
A
0
B
@
x
y
z
1
C
A
(2.65)
Furthermore, we need to remember that integration over a volume element d x d y d z becomes,
after changing of variables r 2 s i n d r d d ' . This may be remembered by the fact that r 2 s i n is
the determinant of the Jacobian matrix, i.e. the matrix obtained by filling a 3 3 matrix with all
partial derivatives of Eq. 2.64. After some algebra, we can write the spherical Laplacian:
r
2
U =
1
r
2
@
@ r
r
2
@ U
@ r
+
1
r
2
s i n
@
@
s i n
@ U
@
+
1
r
2
s i n
2
@
2
U
@ '
2
!
= 0 : (2.66)
2.5 Spherical harmonics
We now attempt to solve Laplaces Equationr
2
U = 0
, in spherical coordinates. Laplaces equa-
tion is obeyed by potential fields outside the sources of the field. Remember how sines and cosines
(or in general, exponentials) are often solutions to differential equations, of the forms i n k x
or
c o s k x
, wherebyk
can take any integer value. The general solution is any combination of sines
and cosines of all possible k s with weights that can be determined by satisfying the boundary
conditions (BCs). The particular solution is constructed by finding a linear combination of these
(basis) functions with weighting coefficients dictated by the BCs: it is a series solution. In the
Cartesian case they are Fourier Series. In Fourier theory, a signal, say a time series s ( t ) , for in-
stance a seismogram, can be represented by the superposition of c o s and s i n functions and weights
can be found which approximate the signal to be analyzed in a least-squares sense.Spherical harmonics are solutions of the spherical Laplaces Equation: they are basically an adap-
tion of Fourier analysis to a spherical surface. Just like with Fourier series, the superposition of
spherical harmonics can be used to represent and analyze physical phenomena distributed on the
surface on (or within) the Earth. Still in analogy with Fourier theory, there exists a sampling the-
orem which requires that sufficient data are provided in order to make the solution possible. In
geophysics, one often talks about (spatial) data coverage, which must be adequate.
-
8/4/2019 Graved Admit
20/40
46 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
We can find a solution for U of r 2 U = 0 by the good old trick of separation of variables. We look
for a solution with the following structure:
U ( r ' ) = R ( r ) P ( ) Q ( ' ) (2.67)
Lets take each factor separately. In the following, an outline is given of how to find the solution
of this elliptic equation, but working this out rigorously requires some more effort than you mightbe willing to spend. But lets not try to lose the physical meaning what we come up with.
Radial dependence: R ( r )
It turns out that the functions satisfying Laplaces Equation belong to a special class of homoge-
neous7 harmonic8 functions. A first property of homogeneous functions that can be used to our
advantage is that in general, a homogeneous function can be written in two different forms:
U
1
( r ' ) = r
l
Y
l
( ' ) (2.68)
U
2
( r ' ) =
1
r
( l + 1 )
Y
l
( ' )
(2.69)
This, of course, gives the form of our radial function:
R ( r ) =
8
-
8/4/2019 Graved Admit
21/40
2.5. SPHERICAL HARMONICS 47
Latitudinal dependence: P ( )
The condition is similar, except it involves both l and m . After some rearranging, one arrives at
s i n
d
d
s i n
d
d
P ( )
+ l ( l + 1 ) s i n
2
m
2
] P ( ) = 0 :
(2.73)
This equation is the associated Legendre Equation. It turns out that the space of the homoge-neous functions has a dimension 2 l + 1 , hence 0 m l .
If we substitute c o s = z , Eq. 2.73 becomes
( 1 z
2
)
d
2
d z
2
P ( z ) 2 z
d
d z
P +
"
l ( l + 1 )
m
2
1 z
2
#
P ( z ) = 0 : (2.74)
Eq. 2.74 is in standard form and can be solved using a variety of techniques. Most commonly,
the solutions are found as polynomialsP
m
l
( c o s )
. The associated Legendre Equation reduces to
the Legendre Equation in casem = 0
. In the latter case, the longitudinal dependence is lost as
also Eq. 2.72 reverts to a constant. The resulting functionsP
l
( c o s )
have a rotational symmetry
around thez
-axis. They are called zonal functions.
It is possible to find expressions of the (associated) Legendre polynomials that summarize theirbehavior as follows:
P
l
( z ) =
1
2
l
l !
d
l
d z
l
( z
2
1 )
l (2.75)
P
m
l
( z ) =
( 1 z
2
)
m
2
l ! 2
l
d
l + m
d z
l + m
( z
2
1 )
l
(2.76)
written in terms of the( l + m )
t h derivative andz = c o s
. It is easy to make a small table with these
polynomials (note that in Table 2.1, we have used some trig rules to simplify the expressions.)
this should get you started in using Eqs. 2.75 or 2.76.
lP
l
( z ) P
l
( )
0 1 1
1 z c o s
2 12
( 3 z
2
1 )
1
4
( 3 c o s 2 + 1 )
3 12
( 5 z
3
3 z )
1
8
( 5 c o s 3 + 3 c o s )
Table 2.1: Legendre polynomials.
Some Legendre functions are plotted in Figure 2.13.
Spherical harmonics
The generic solution for U is thus found by combining the radial, longitudinal and latitudinal
behaviors as follows:
U ( r ' ) =
8
-
8/4/2019 Graved Admit
22/40
48 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
0 0.5 1 1.5 2 2.5 3
1
0.8
0.6
0.4
0.2
0
0.2
0.4
0.6
0.8
1
P(cos
)
P0
P1
P2
P3
Figure 2.13: Legendre polynomials.
These are called the solid spherical harmonics ofdegreel
and orderm
.
The spherical harmonics form a complete orthonormal basis. We implicitly assume that the full
solution is given by a summation over all possible l and m indices, as in:
U ( r ' ) =
1
X
l = 0
l
X
m = 0
8
-
8/4/2019 Graved Admit
23/40
2.5. SPHERICAL HARMONICS 49
Figure 2.14: Some spherical harmonics.
The sectorial harmonics are of the form s i n ( m ' ) P mm
( c o s ) or c o s ( m ' ) P mm
( c o s ) . As
they vanish at2 m
meridians (longitudinal lines, som
great circles), they divide the sphere
into sectors.
The tesseral harmonics are those of the form s i n ( m ' ) P ml
( c o s ) or c o s ( m ' ) P ml
( c o s )
for l 6= m . The amplitude of a surface spherical harmonic of a certain degree l and order m
vanishes at 2 m meridians of longitude and on ( l m ) parallels of latitude.
In other words the degree l gives the total number of nodal lines and the order m controls how
this number is distributed over nodal meridians and nodal parallels. The higher the degree and
order the finer the detail that can be represented, but increasing l and m only makes sense if data
coverage is sufficient to constrain the coefficients of the polynomials.
A different rendering is given in Figure 2.15.
Finally, an important property follows from the depth dependence of the solution:
-
8/4/2019 Graved Admit
24/40
50 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
ZonalP
5,0
SectoralP
5,5
TesseralP
5,3
Figure 2.15: Zonal, tesseral and sectoral spherical harmonics.
From eqn. (2.78) we can see that (1) the amplitude of all terms will decrease with increasing
distance from the origin (i.e., the internal source of the potential) and that (2) the rate of decay
increases with increasing degree l .
This has the following consequences:
1. with increasing distance the lower order harmonics become increasingly dominant since the
signal from small-scale structure (largel
s andm
s) decays more rapidly. Recall that the
perturbations of satellite orbits constrain the lower orders very accurately. The fine details
at depth are difficult to discern at the surface of the Earth (or further out in space) owing to
this spatial attenuation.
2. Conversely, this complicates the downward continuation of U ( r ' ) from the Earths sur-
face to a smaller radius, since this process introduces higher degree components in the so-
lutions that are not constrained by data at the surface. This problem is important in the
downward continuation of the magnetic field to the core-mantle-boundary.
2.6 Global gravity anomalies
Gravity in and outside a spherical mass sheet
The full solution to Laplaces equation was given in Equation 2.78. Weve talked about the choice
of radial functions. Inside the mass distribution, we use
U
i n
( r ' ) =
n
r
l
o
A
m
l
c o s m ' + B
m
l
s i n m ' ] P
m
l
( c o s )
(2.80)
and outside, we use
U
o u t
( r ' ) =
1
r
l + 1
A
m
l
c o s m ' + B
m
l
s i n m ' ] P
m
l
( c o s )
(2.81)
From now on, well add a normalization factor witha
the radius at the equator:
U
o u t
( r ' ) =
G M
a
1
X
l = 0
l
X
m = 0
a
r
l + 1
A
m
l
c o s m ' + B
m
l
s i n m ' ] P
m
l
( c o s ) (2.82)
-
8/4/2019 Graved Admit
25/40
2.6. GLOBAL GRAVITY ANOMALIES 51
So in terms of a surface spherical harmonic potential U ( l ) on the unit circle, we get the following
equations for the field in- and outside the mass distribution:
U
i n
( r l ) =
r
a
l
U ( l )
U
o u t
( r l ) =
a
r
l + 1
U ( l )
(2.83)
For the gravity, this becomes:
g
i n
( r l ) =
l
a
l
r
l 1
U ( l ) r
g
o u t
( r l ) = a
l + 1
( l + 1 )
1
r
l + 1
U ( l ) r (2.84)
What is the gravity due to a thin sheet of mass of spherical harmonic degree l ? Lets represent this
as a sheet with vanishing thickness, and call ( l )
the mass density per unit area. This way we can
work at constantr
and use the results for spherical symmetry. We know from Gausss law that the
flux through any surface enclosing a bit of mass is equal to the total enclosed mass (times 4 G
).
So constructing a box around a patch of surfaceS
with aread S
, enclosing a bit of massd M
, we
can deduce that
g
o u t
g
i n
= 4 G ( l ) (2.85)
On this shell give it a radius a, we can use Eqs. 2.84 to find go u t
= U ( l ) ( l + 1 ) = a and
g
i n
= U ( l ) l = a , and solve for U ( l ) using Eq. 2.85 as U ( l ) = 4 G ( l ) a = ( 2 l + 1 ) . Plugging
this into Eqs. 2.84 again we get for the gravity in- and outside this mass distribution
g
i n
( r l ) =
4 G l
2 l + 1
( l )
r
l 1
a
l 1
g
o u t
( r l ) =
4 G l ( l + 1 )
2 l + 1
( l )
a
l + 2
r
l + 2
(2.86)
Length scales
Measurements of gravitational attraction are as we have seen useful in the determination
of the shape and rotational properties of the Earth. This is important for geodesy. In addition,
they also provide information about aspherical density variations in the lithosphere and mantle
(important for understanding dynamical processes, interpretation of seismic images, or for finding
mineral deposits). However, before gravity measurements can be used for interpretation severalcorrections will have to be made: the data reductions plays an important role in gravimetry since
the signal pertinent to the structures we are interested in is very small.
Lets take a step back and get a feel for the different length scales and probable sources involved.
If we use a spherical harmonic expansion of the fieldU
we can see that its the up- or downward
continuation of the field and its dependence onr
and degreel
that controls the behavior of the
solution at different depths (or radius) (remember Eq. 2.82).
-
8/4/2019 Graved Admit
26/40
52 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
With increasing r from the source the amplitude of the surface harmonics become smaller and
smaller, and the decay in amplitude (spatial attenuation) is stronger for the higher degrees l (i.e.,
the small-scale structures).
Intermezzo 2.8 CARTESIAN VS SPHERICAL REPRESENTATION
If you work on a small scale with local gravity anomalies (for instance in exploration geophysics) it isnot efficient to use (global) basis functions on a sphere because the number of coefficients that youd need
would simply be too large. For example to get resolution of length scales of 100 km (about 1 ) you need
to expand up to degreel
=360 which with all the combinations0 < m < l
involves several hundreds of
thousands of coefficients (how many exactly?). Instead you would use a Fourier Series. The concept is
similar to spherical harmonics. A Fourier series is just a superposition of harmonic functions (sine and
cosine functions) with different frequencies (or wave numbersk = 2 =
,
the wavelength):
g
z
= c o n s t a n t s i n ( k
x
x ) e
k
x
z
= c o n s t a n t s i n
2 x
x
e
2 z
x (2.87)
(For a 2D field the expression includes y but is otherwise be very similar.) Or, in more general form
g
z
=
1
X
n = 0
h
a
n
c o s
n x
x
0
+ b
n
s i n
n x
x
0
i
e
n z
x
0 (2.88)
(compare to the expression of the spherical harmonics). In this expressionx
0
specifies the size of the grid
at which the measurements are made, and the up- and downward continuation of the 1D or 2D harmonic
field is controlled by an exponential form. The problem with downward continuation becomes immediately
clear from the following example. Suppose in a marine gravity expedition to investigate density variation in
the sediments beneath the sea floor, say, at 2 km depth, gravity measurements are taken at 10 m intervals on
the sea surface. Upon downward continuation, the signal associated with the smallest wavelength allowed
by such grid spacing would be amplified by a factor ofe x p ( 2 0 0 0 = 1 0 ) =
e x p ( 2 0 0 ) 1 0
2 7 3 . (The water does not contain any concentrations of mass that contribute to the gravity
anomalies and integration over the surface enclosing the water mass would add only a constant value to the
gravity potential but that is irrelevant when studying anomalies, and Laplaces equation can still be used.)
So it is important to filter the data before the downward continuation so that information is maintained only
on length scales that are not too much smaller than the distance over which the downward continuation has
to take place.
Table 2.2 gives and idea about the relationship between length scales, the probable source regions,
and where the measurements have to be taken.
wavelength short wavelength long wavelength
( 3 6 ) ( > 1 0 0 0 km or l
-
8/4/2019 Graved Admit
27/40
2.6. GLOBAL GRAVITY ANOMALIES 53
The free-air gravity anomaly
Lets assume that the geoid height N with respect to the spheroid is due to an anomalous mass
d M . If d M represents excess mass, the equipotential is warped outwards and there will be a geoid
high (N > 0 ); conversely, if d M represents a mass deficiency, N
-
8/4/2019 Graved Admit
28/40
54 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
(Remember that g0
is the magnitude of the negative gradient of U and therefore appears with a
positive sign.) We knew from Eq. 2.89 that
U ( P ) = U
0
( P ) + U ( P )
= U
0
( Q ) + g
0
N + U ( P )
(2.92)
But also, since the potentials of U and U0
were equal, U ( P ) = U0
( Q ) and we can write
g
0
N = U ( P ) (2.93)
This result is known as Bruns formula. Now for the gravity vectors g and g0
, they are given by
the familiar expressions
g = r U
g
0
= r U
0
(2.94)
and the gravity disturbance vector g = g g0
can be defined as the difference between those
two quantities:
g = r U
g = g g
0
=
d U
d r
(2.95)
On the other hand, from a first-order expansion, we learn that
g
0
( P ) = g
0
( Q ) +
d g
0
d r
r
0
N
g ( P ) = g
0
( Q ) +
d g
0
d r
r
0
N +
d U
d r
(2.96)
(2.97)
Now we define the free-air gravity anomaly as the difference of the gravitational accelartion
measured on the actual geoid (if youre on a mountain youll need to refer to sea level) minus the
reference gravity:
g = g ( P ) g
0
( Q ) (2.98)
This translates into
g =
d g
0
d r
r
0
N +
d U
d r
=
d
d r
G M
r
2
r
0
N +
d U
d r
-
8/4/2019 Graved Admit
29/40
2.6. GLOBAL GRAVITY ANOMALIES 55
=
2
r
0
G M
r
2
0
N +
d U
d r
=
2
r
0
g
0
N +
d U
d r
g =
2
r
0
U +
d U
d r
(2.99)
(2.100)
So at this arbitrary point P on the geoid, the gravity anomaly g due to the anomalous mass arises
from two sources: the direct contribution d gm
due to the extra acceleration by the mass d M itself,
and an additional contribution d gh
that arises from the fact that g is measured on height N above
the reference spheroid. The latter term is essentially a free air correction, similar to the one one
has to apply when referring the measurement (on a mountain, say) to the actual geoid (sea level).
Note that Eq. (2.93) contains the boundary conditions of r 2 U = 0 . The geoid height N at
any point depends on the total effect of mass excesses and deficiencies over the Earth. N can be
determined uniquely at any point ( ' ) from measurements of gravity anomalies taken over the
surface of the whole Earth this was first done by Stokes (1849) but it does not uniquely
constrain the distribution of masses.
Gravity anomalies from geoidal heights
A convenient way to determine the geoid heights N ( ' ) from either the potential field anomalies
U ( ' ) or the gravity anomalies g ( ' ) is by means of spherical harmonic expansion of
N ( ' ) in terms of U ( ' ) or g ( ' ) .
Its convenient to just give the coefficients of Eq. 2.82 since the basic expressions are the same.
Lets see how that notation would work for eq. (2.82):
(
U
A
U
B
)
=
G M
a
(
A
m
l
B
m
l
)
(2.101)
Note that the subscripts A and B are used to label the coefficients of the c o s m ' and s i n m ' parts,
respectively. Note also that we have now taken the factor G M a l as the scaling factor of the
coefficients.
We can also expand the potential U0
on the reference spheroid:
(
U
0 A
U
0 B
)
=
G M
a
(
A
0
m
l
0
)
(2.102)
(Note that we did not drop the m , even though m = 0 for the zonal harmonics used for the
reference spheroid. We just require the coefficient A0
m
l
to be zero for m 6= 0 . By doing this we
can keep the equations simple.)
The coefficients of the anomalous potential U ( ' ) are then given by:
(
U
A
U
B
)
=
G M
a
(
( A
m
l
A
0
m
l
)
B
m
l
)
(2.103)
We can now expand g ( ' )
in a similar series using eq. (2.99). For the U
, we can see by
inspection that the radial derivative as prescribed has the following effect on the coefficients (note
that the reference radiusr
0
= a
from earlier definitions):
-
8/4/2019 Graved Admit
30/40
56 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
d U
d r
!
l + 1
r
0
(2.104)
and the other term of Eq. 2.99 brings down
2
r
0
U !
2
a
(2.105)
As a result, we get
(
g
A
g
B
)
=
G M
a
l + 1
a
(
( A
m
l
A
0
m
l
)
B
m
l
)
(2.106)
= g
0
( l 1 )
(
( A
m
l
A
0
m
l
)
B
m
l
)
(2.107)
The proportionality with ( l 1 ) g0
means that the higher degree terms are magnified in the gravity
field relative to those in the potential field. This leads to the important result that gravity mapstypically contain much more detail than geoid maps because the spatial attenuation of the higher
degree components is suppressed.
Using Eq. (2.93) we can express the coefficients of the expansion of N ( ' ) in terms of either the
coefficients of the expanded anomalous potential
g
0
(
N
A
N
B
)
=
G M
a
(
( A
m
l
A
0
m
l
)
B
m
l
)
(2.108)
which, if we replace g by g and by assuming that g g gets the following form
(
N
A
N
B
)
= a
(
( A
m
l
A
0
m
l
)
B
m
l
)
(2.109)
or in terms of the coefficients of the gravity anomalies (eqns. 2.107 and 2.109)
(
N
A
N
B
)
=
a
( l 1 ) g
0
(
g
A
g
B
)
= a
(
( A
m
l
A
0
m
l
)
B
m
l
)
(2.110)
The geoid heights can thus be synthesized from the expansions of either the gravity anomalies
(2.110) or the anomalous potential (2.109). Geoid anomalies have been constructed from both
surface measurements of gravity (2.110) and from satellite observations (2.109). Equation (2.110)
indicates that relative to the gravity anomalies, the coefficients of N ( ' ) are suppressed by a
factor of1 = ( l 1 )
. As a result, shorter wavelength features are much more prominent on gravitymaps. In other words, geoid (and geoid height) maps essentially depict the low harmonics of the
gravitational field. A final note that is relevant for the reduction of the gravity data. Gravity data
are typically reduced to sea-level, which coincides with the geoid and not with the actual reference
spheroid. Eq. 8 can then be used to make the additional correction to the reference spheroid, which
effectively means that the long wavelength signal is removed. This results in very high resolution
gravity maps.
-
8/4/2019 Graved Admit
31/40
2.7. GRAVITY ANOMALIES AND THE REDUCTION OF GRAVITY DATA 57
2.7 Gravity anomalies and the reduction of gravity data
The combination of the reduced gravity field and the topography yields important information on
the mechanical state of the crust and lithosphere. Both gravity and topography can be obtained
by remote sensing and in many cases they form the basis of our knowledge of the dynamical state
of planets, such as Mars, and natural satellites, such as Earths Moon. Data reduction plays an
important role in gravity studies since the signal caused by the aspherical variation in density thatone wants to study are very small compared not only to the observed field but also other effects,
such as the influence of the position at which the measurement is made. The following sum shows
the various components to the observed gravity, with the name of the corresponding corrections
that should be made shown in parenthesis:
Observed gravity = attraction of the reference spheroid, PLUS:
effects of elevation above sea level (Free Air correction), which should include the eleva-
tion (geoid anomaly) of the sea level above the reference spheroid
effect of normal attracting mass between observation point and sea level (Bouguer and
terrain correction)
effect of masses that support topographic loads (isostatic correction)
time-dependent changes in Earths figure of shape (tidal correction)
effect of changes in the rotation term due to motion of the observation point (e.g. when
measurements are made from a moving ship. (E otvos correction)
effects of crust and mantle density anomalies (geology or geodynamic processes).
Only the bold corrections will be discussed here. The tidal correction is small, but must be ac-
counted for when high precision data are required. The application of the different corrections is
illustrated by a simple example of a small density anomaly located in a topography high that isisostatically compensated. See series of diagrams.
Free Air Anomaly
So far it has been assumed that measurements at sea level (i.e. the actual geoid) were available.
This is often not the case. If, for instance, g is measured on the land surface at an altitude h one
has to make the following correction :
d g
F A
= 2
h g
r
(2.111)
Forg
at sea level this correction amounts tod g
F A
= 0 : 3 0 8 6 h
mgal or0 : 3 0 8 6 h 1 0
5
ms 2
(h
inmeter). Note that this assumes no mass between the observer and sea level, hence the name free-
air correction. The effect of ellipticity is often ignored, but one can user = R
e q
( 1 f s i n
2
)
.
Note: per meter elevation this correction equals3 : 1 1 0
6 ms 2 3 : 1 1 0
7
g
: this is on the
limit of the precision that can be attained by field instruments, which shows that uncertainties in
elevation are a limiting factor in the precision that can be achieved. (A realistic uncertainty is 1
mgal).
-
8/4/2019 Graved Admit
32/40
58 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
Make sure the correction is applied correctly, since there can be confusion about the sign of the
correction, which depends on the definition of the potential. The objective of the correction is to
compensate for the decrease in gravity attraction with increasing distance from the source (center
of the Earth). Formally, given the minus sign in (2.112), the correction has to be subtracted, but
it is not uncommon to take the correction as the positive number in which case it will have to be
added. (Just bear in mind that you have to make the measured value larger by adding gravity
so it compares directly to the reference value at the same height; alternatively, you can make the
reference value smaller if you are above sea level; if you are in a submarine you will, of course,
have to do the opposite).
The Free Air anomaly is then obtained by the correction for height above sea level and by sub-
traction of the reference gravity field
g
F A
= g
o b s
d g
F A
g
0
( ) = ( g
o b s
+ 0 : 3 0 8 6 h 1 0
3
) g
0
( ) (2.112)
(Note that there could be a component due to the fact that the sea level ( the geoid) does not
coincide with the reference spheroid; an additional correction can then be made to take out the
extra gravity anomaly. One can simply apply (2.112) and use h 0 = h + N as the elevation, which
is equivalent to adding a correction tog
0
( )
so that it represents the reference value at the geoid.
This correction is not important if the variation in geoid is small across the survey region because
then the correction is the same for all data points.)
Bouguer anomaly
The free air correction does not correct for any attracting mass between observation point and sea
level. However, on land, at a certain elevation there will be attracting mass (even though it is often
compensated - isostasy (see below)). Instead of estimating the true shape of, say, a mountain on
which the measurement is made, one often resorts to what is known as the slab approximation in
which one simply assumes that the rocks are of infinite horizontal extent. The Bouguer correction
is then given by
d g
B
= 2 G h (2.113)
whereG
is the gravitational constant,
is the assumed mean density of crustal rock andh
is the
height above sea level. ForG = 6 : 6 7 1 0
1 1 m3 kg 3 s 2 and = 2 7 0 0
kgm 3 we obtain
a correction of1 : 1 1 0
6 ms 2 per meter of elevation (or0 : 1 1 h
mgal,h
in meter). If the
slab approximation is not satisfactory, for instance near the top of mountains, on has to apply an
additional terrain correction. It is straightforward to apply the terrain correction if one has access
to digital topography/bathymetry data.
The Bouguer anomaly has to be subtracted, since one wants to remove the effects of the extra
attraction. The Bouguer correction is typically applied after the application of the Free Air cor-
rection. Ignoring the terrain correction, the Bouguer gravity anomaly is then given by
g
B
= g
o b s
d g
F A
g
0
( ) d g
B
= g
F A
d g
B
(2.114)
In principle, with the Bouguer anomaly we have accounted for the attraction of all rock between
observation point and sea level, and g
B
thus represents the gravitational attraction of the material
below sea level. Bouguer Anomaly maps are typically used to study gravity on continents whereas
the Free Air Anomaly is more commonly used in oceanic regions.
-
8/4/2019 Graved Admit
33/40
2.7. GRAVITY ANOMALIES AND THE REDUCTION OF GRAVITY DATA 59
Isostasy and isostatic correction
If the mass between the observation point and sea level is all that contributes to the measured
gravity one would expect that the Free Air anomaly is large, and positive over topography highs
(since this mass is unaccounted for) and that the Bouguer anomaly decreases to zero. This rela-
tionship between the two gravity anomalies and topography is indeed what would be obtained in
case the mass is completely supported by the strength of the plate (i.e. no isostatic compensation).In early gravity surveys, however, they found that the Bouguer gravity anomaly over mountain
ranges was, somewhat surprisingly, large and negative. Apparently, a mass deficiency remained
after the mass above sea level was compensated for. In other words, the Bouguer correction sub-
tracted too much! This observation in the 19t h century lead Airy and Pratt to develop the concept
of isostasy. In short, isostasy means that at depths larger than a certain compensation depth the
observed variations in height above sea level no longer contribute to lateral variations in pressure.
In case of Airy Isostasy this is achieved by a compensation root, such that the depth to the inter-
face between the loading mass (with constant density) and the rest of the mantle varies. This is, in
fact Archimedes Law, and a good example of this mechanism is the floating iceberg, of which we
see only the top above the sea level. In the case of Pratt Isostasy the compensation depth does not
vary and constant pressure is achieved by lateral variations in density. It is now known that bothmechanisms play a role.
Figure 2.18: Airy and Pratt isostasy.
The basic equation that describes the relationship between the topographic height and the depth of
the compensating body is:
H =
c
h
m
c
(2.115)
Figure 2.19: Airy isostasy.
-
8/4/2019 Graved Admit
34/40
60 CHAPTER 2. THE EARTHS GRAVITATIONAL FIELD
Assuming Airy Isostasy and some constant density for crustal rock one can compute H ( x y ) from
known (digital) topography h ( x y ) and thus correct for the mass deficiency. This results in the
Isostatic Anomaly. If all is done correctly the isostatic anomaly isolates the small signal due to
the density anomaly that is not compensated (local geology, or geodynamic processes).
2.8 Correlation between gravity anomalies and topography.
The correlation between Bouguer and Free Air anomalies on the one hand and topography on the
other thus contains information as to what level the topography is isostatically compensated.
In the case of Airy Isostasy it is obvious that the compensating root causes the mass deficiency that
results in a negative Bouguer anomaly. If the topography is compensated the mass excess above
sea level is canceled by the mass deficiency below it, and as a consequence the Free Air Anomaly
is small; usually, it is not zero since the attracting mass is closer to the observation point and is
thus less attenuated than the compensating signal of the mass deficiency so that some correlation
between the Free Air Anomaly and topography can remain.
Apart from this effect (which also plays a role near the edges of topographic features), the Free
air anomaly is close to zero and the Bouguer anomaly large and negative when the topography iscompletely compensated isostatically (also referred to as in isostatic equilibrium).
In case the topography is NOT compensated, the Free air anomaly is large and positive, and the
Bouguer anomaly zero.
(This also depends on the length scale of the load and the strength of the supporting plate).
Whether or not a topographic load is or can be compensated depends largely on the strength (and
the thickness) of the supporting plate and on the length scale of the loading structure. Intuitively it
is obvious that small objects are not compensated because the lithospheric plate is strong enough
to carry the load. This explains why impact craters can survive over very long periods of time!
(Large craters may be isostatically compensated, but the narrow rims of the crater will not disap-
pear by flow!) In contrast, loading over large regions, i.e. much larger than the distance to the
compensation depth, results in the development of a compensating root. It is also obvious why
the strength (viscosity) of the plate enters the equation. If the viscosity is very small, isostatic
equilibrium can occur even for very small bodies (consider, for example, the floating iceberg!).
Will discuss the relationship between gravity anomalies and topography in more (theoretical) de-
tail later. We will also see how viscosity adds a time dependence to the system. Also this is easy
to understand intuitively; low strength means that isostatic equilibrium can occur almost instantly
(iceberg!), but for higher viscosity the relaxation time is much longer. The flow rate of the material
beneath the supporting plate determines how quickly this plate can assume isostatic equilibrium,
and this flow rate is a function of viscosity. For large viscosity, loading or u