GOVERNMENT POLYTECHNIC, KHAMGAON · 2020. 8. 8. · Trainer kit for MOSFET Trainer kit suitable to...
Transcript of GOVERNMENT POLYTECHNIC, KHAMGAON · 2020. 8. 8. · Trainer kit for MOSFET Trainer kit suitable to...
Page 1 of 6
No. : GPK/EQP/inst purchase/ETX_List-A/2018-19/3256 Date: 01/12/2018
By post / email
To,
……………………….
……………………….
………………………..
………………………..
QUOTATION
Sub: Quotation for purchase of equipment / furniture.
(Due Date 02/01/2019 & Date of Opening: 03/01/2019) Dear Sir,
Sealed Quotations are invited from eligible and interested manufacturers/ dealers/distributors/
for the following items on the terms and conditions mentioned below.
Sr. No.
Name of the item with specification
Quantity required
Approximate cost per unit
(Inclusive of GST and all)
(Rs.)
Name of the item
Specification
1 Trainer kit for MOSFET
Trainer kit suitable to plot I/p, O/P characteristic of MOSFET with inbuilt DC supply and required digital meters (4 No.) and various Test point
2 4000
2 Trainer kit for single tuned amplifier
Trainer kit suitable to plot the frequency response of a Transistorized L-C tuned (single) circuit amplifier. Centre frequency above 400 KHz. (any other suitable frequency) Inbuilt DC supply and various Test points.
2 4000
3 Trainer Kit suitable to plot Anode
Trainer kit suitable to plot anode - cathode characteristics and gate characteristics of silicon controlled Rectifier (SCR). 0 - 10V and 0 - 150V DC power supply of required current rating & 4 no of digital voltmeter & current meter are inbuilt in the kit.
1 4000
4 Study of SCR Turn ON Methods
Trainer kit suitable to study the basic triggering methods of SCR like Resistance triggering circuit; R-C triggering circuit. Should be provided with SCR, Lamp load (15W) & isolation transformer. Trainer kit should demonstrate effect of variation of resistor and capacitor in R & RC triggering circuit on firing angle of SCR. SCR should be operated on 230V, 50Hz AC supply
1 4000
GOVERNMENT POLYTECHNIC, KHAMGAON
WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram: - POLYTECH
Page 2 of 6
5 Study of SCR Turn ON Methods
Trainer kit suitable to study the SCR triggering using Synchronized UJT triggering. Trainer kit should demonstrate effect of variation R on firing angle in Synchronized UJT triggering circuit.
1 4000
6
Trainer kit for single stage and Multistage BJT amplifier
Trainer kit suitable to plot Frequency response of 2 stage common emitter transistor amplifier circuit. Facility to measure A1& A1xA2. Inbuilt DC supply and various Test points.
2 3000
7 Trainer Kit for FM Modulator using IC 566
AC Source:600Hz-2.5KHz, FM Modulator: VCO, Test Points, Circuit diagram engraved on front panel with transparent rear panel
2 4000
8
Trainer Kit for FM Demodulator using IC 564/565
AC Source:600Hz-2.5KHz, FM Demodulator: VCO, Test Points, Circuit diagram engraved on front panel with transparent rear panel
2 4000
9 Antenna trainer kit
Waveforms: Sine RF Generator: 750 MHz approximately (output adjustable) Tone Generator : 1 KHz approximately (output adjustable).Directional Coupler: Forward & Reverse (selectable).Matching Stub : Slider type. Antenna Rotation: 0-360 deg. Resolution 1 deg. Antenna Rotation: 0-360 deg. Resolution 1 deg. Receiving Antenna: Folded dipole with reflector. Detector Display: Level adjustable meter Interconnections: 2 mm Banana sockets Antenna with Radiation Pattern Plotting Software and 10 Antennas RF Generator for easy experimentation with built-in modulation and DC transmitting mast, and receiving mast with detector. Experiment with different types of antennas. Antenna Fabrication kit Forward / Reverse power & SWR measurements
2 6000
10
Trainer kit for Sampling theorem and PCM modulation and demodulation
STUDY OF SAMPLING THEOREM. Trainer kit suitable to demonstrate the principle of Sampling theorem which is basic of digital communication system by IC based circuit. Kit should have built in Clock generator, Pulse generator Sample & Hold circuit, Microphone Preamplifier & Filter circuit. Also provided with signal recovery section. Effect of aliasing should be demonstrated. Inbuilt DC supply and various Test points. ii) PULSE CODE MODULATION. Trainer kit suitable to demonstrates the principle of pulse code modulation. Kit should consist of Crystal based clock generator, Divider circuit, A to D converter and parallel to serial converter. Trainer should give the pulse code modulated signal at output. Inbuilt DC supply and various Test points. iii) PULSE CODE DEMODULATION. Trainer kit suitable to demonstrate the principle of pulse code demodulation using IC based circuit. Kit consists of serial to parallel converter, D to A converter, filter and amplifier. This unit should be matched with PCM trainer & original modulating
2 5000
Page 3 of 6
11
Trainer kit for DPCM modulation and demodulation
Onboard DPCM Transmitter and receiver. Onboard Audio input & output processing. Circuits Clock and entire control Signal section. Detailed signal processing circuit with complete data and control signal flow Signal generator block. Functions: Sine and Square O/P frequency range: 300Hz to 3.4 KHz Audio blocks: Audio I/P and O/P processing circuits Control signals: R/W for ADC, reset. Latch enables, OEs. Sampling frequency : 8 KHz Total Bits per sample :5 bits including sign bit Compared to 8 bit PCM :3 bits per sample
2 7500
12
Trainer kit for delta and adaptive delta modulation
Input Channel: Time Division Multiplexed .Serial Crystal Frequency: 6.400 MHz Sampling Clock Frequency: 50, 100, 200 & 400 KHz (Switch selectable).On board Generator: Synchronized and Adjustable Integrator: Four integrator gain settings .Normal, X 2, X 4, X 8Low Pass Filter: Fourth order Butterworth (Cut Off Frequency 4.8 KHz).
2 7500
13
Trainer kit for Study of Data Formats. Line code trainer for UPNRZ, PRZ, BPRZ, PNRZ, and UNRZ. Manchester and Differential
Technical Specification .Data Formatting and Carrier Modulation Transmitter .Crystal Frequency: 4.096 MHz Data formats: NRZ (L), NRZ (M), RZ, AMI, and RB. Biphase (Manchester), Biphase (Mark).On-board carrier : Sine waves synchronized to transmitted data at 1.6 MHz, 960 KHz, (0 deg. phase) 960 KHz, (90 deg. phase) Power Supply : 220/110V, 50/60 Hz.
2 5000
14
Trainer kit for ASK , PSK , FSK modulation and Demodulation
Trainer kit for Study of keying techniques .For Study of Amplitude Shift Keying Study of Frequency Shift Keying for Study of Phase Shift Keying for Study of Differential Phase Shift Keying for Study of Quadrature Phase Shift Keying Study of Differential Quadrature Phase Shift Keying Technical Specifications Carrier Demodulation and Data Reformatting Receiver IC carrier Demodulation : ASK - Rectifier
2 7500
15
Trainer kit for QPSK modulation and Demodulation
Trainer kit shall demonstrate principle of QPSK modulation and demodulation
2 4000
16
Trainer kit for QAM modulation and Demodulation
Trainer kit shall demonstrate principle of QAM modulation and demodulation
2 5000
Page 4 of 6
17
Trainer kit for DPSK modulation and demodulation
Trainer kit shall demonstrate principle of DPSK modulation and demodulation
2 5000
18
Trainer kit for FDM and TDM and de-multiplexing
Trainer kit shall demonstrate principle of FDM and TDM multiplexing and DE multiplexing
2 10000
19
CDMA – DSSS signal generator and demodulator
Trainer kit shall demonstrate principle of CFMA DSSS signal generation and demodulation
2 10000
20 FHSS signal modulator and demodulator
On-board data generators and PRN sequence generators. BCD rotary switches for Data Selection Tap selectable PN sequence generators Multiple data rate and chip rate selection Variable processing gain selection Slow and Fast frequency hopping demonstration PN sequence driven Frequency synthesizer with non-overlapping frequency channel assignment Data Rates :16 Kbps, 8 Kbps and 4 Kbps Word Length :8 bits Data Format :NRZ (Not Return to Zero) Chip Rates :240 KHz, 120 KHz, 60 KHz, (DSSS CDMA)16 KHz, 8 KHz and 4 KHz (for FHSS) Sequence Type :Maximum Length Sequence Sequence Pattern :Selectable through feedback taps in LFSR array. BFSK Frequencies: 100 KHz for mark and 50 KHz for space. Frequency Synthesizer Output: Sinusoidal Frequency Synthesizer: 1.6 MHz, 1.2 MHz, 800 KHz and 400 KHz. Channels Hoping Channels :Four Number of Hopes :Variable depending upon data rate and chip rate per Data Periods
2 10000
21 Trainer kit for UJT
Trainer kit suitable to plot V I characteristic of UJT with inbuilt DC supply and required digital meters (2 No.) and various Test point
2 4000
22 Trainer kit for RC Phase shift oscillator
Trainer kit suitable to produce oscillations of frequency 10 KHz (any other suitable frequency) Inbuilt DC supply and various Test points.
2 5000
23 Trainer kit for crystal oscillator
Trainer kit suitable to produce oscillations of frequency 10 KHz (any other suitable frequency) Inbuilt DC supply and various Test points.
2 5000
24
Trainer kit for negative feedback amplifier
Trainer kit suitable to plot the frequency response with and without Voltage series feedback, Voltage shunt, Current series and current shunt feedback. Inbuilt DC supply and various Test points.
2 5000
(Note: Please note the terms and conditions mentioned below)
Page 5 of 6
TERMS AND CONDITIONS
The bid/quotation should be submitted in two bid format.( Technical bid & Commercial Bid)
The first envelope will contain Technical specifications of the product, technical literature
/ leaflet and other documents mentioned below. It is mandatory to the suppliers to submit
following documents without which your quotation will not be considered.
1. Covering Letter for tender on the company letter head mentioning official address, Contact
No, E-Mail address and website (if available) address.
2. Registration letter of supplier’s establishment (company / organization)
3. EMD in this regard (3% of the quoted cost or Re. 5000 whichever is minimum) to be paid
in the form of DD in favour of Principal, Govt. Polytechnic, Khamgaon OR Exemption
certificate from competent authorities, if exemption is claimed.
4. GST registration certificate / Number.
5. GST Clearance Certificate / GST Challan for last quarter of the financial year. (Paid up to
July 2018)
6. Authorization / Distributorship certificate from manufacturer. Proof of permission to
manufacture
7. The equipment / item mentioned in the quotation from competent authorities. (to be
submitted if the bidder is not a manufacturer)
8. Technical literature / leaflet of the make and model no of equipment quoted.
9. Undertaking by supplier confirming quality of Equipment / Machinery.
10. Under taking by supplier towards supply of equipment within prescribed date / period and
post sales services.
(Additional document may also be asked by undersigned for confirming the details.)
Page 6 of 6
The second envelope will contain the financial bid in which the all inclusive rates F.O.R.
Destination will be written and signed with the stamp of the establishment in the following
format.
Sr.
No.
Name of the item with specification
Quantity
required
All
inclusive
cost per
unit
(Rs.)
All
inclusive
cost for
quantity
mentioned.
(Rs.)
Name of the
item Specifications
Date - (Signature)
Place - Rubber Stamp of Organization
Important Instructions
The two envelopes should be sealed with a mention of the type of envelope (technical /
Financial), Reference no., Date of opening the quotation on the front side of the envelope.
These two envelopes should be sealed in a third envelope by giving heading “Quotation for
supply of “Electronics and Communication Engg. Department Equipment” and writing
complete address of the undersigned. (Address: Principal, Government Polytechnic,
Khamgaon, Jalamb Road, Khamgaon, Dist: Buldana, (M.S.), Pin 444 303.
The quotations should reach the undersigned on or before date 02/01/2019
The material will be checked at this institute.
No extra charges will be paid for cartage, packing etc. for the material rejected and replaced.
Quotations will be opened at 3.00 AM/ PM on date 03/01/2019 at office of the Principal of
Institute.
Rates should be valid for 6 months from the date of confirmation letter.
Materials should be quoted for standard makes and minimum pkgs.
Delivery to the consignee has to be effected within 1 week from the date of issue of purchase
order or on or before the prescribed date. (if any)
The undersigned reserves the right to accept or reject any offer or all offers without assigning
any reason thereof.
The said process is subjected to the necessary approval from higher authorities.
Principal Govt. Polytechnic, Khamgaon.
Copy to:
1) Hon. Director, Directorate of Technical Education M. S. Mumbai for information please. It is requested to
do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information pleases. It is
requested to do needful for uploading the same on website as per instructions issued.
3) Head of Electronics and communication Department for information & n a
4) Suppliers as list attached herewith
5) Shri. Ambatakar, Programmer, GP Khamgaon, for uploading on Institute website.
6) Institute Notice Board
Page 1 of 4
Page 1 of 4
No. : GPK/EQP/inst purchase/APM_List-A/2018-19/3255 Date: 01/12/2018
By post / email
To,
……………………….
……………………….
………………………..
………………………..
QUOTATION
Sub: Quotation for purchase of equipment / furniture.
(Due Date 02/01/2019 & Date of Opening: 03/01/2019) Dear Sir,
Sealed Quotations are invited from eligible and interested manufacturers/ dealers/distributors/
for the following items on the terms and conditions mentioned below.
Sr. No.
Name of the item with specification
Quantity required
Approximate cost per unit
(Inclusive of GST and all)
(Rs.)
Name of the item Specification
1 Oven
Laboratory Electric Oven, Digital Indicator Cum Controller with Safety Alarm, Range 50 deg C to 300deg. C. +/- 1 deg. C. with Air Circulating Fan , S.S. Inside, Size 600 X 600 X 600mm
1 50000
2 Infra-Red Moisture Meter
Standard: IS: 2720 (Part 2) This moisture meter has been designed for rapid and accurate determination of the moisture content of a wide variety of materials.
1 40000
3 Mould for modified Procter Test
Proctor mould having a capacity of 944 cc with an internal diameter of 10.2 cm and a height of 11.6 cm. The mould shall have a detachable collar assembly and a detachable base plate.
5 5000
4 Water Bath Tub for testing Soundness of cement
Bath volume 20L and temperature range from ambient 5C above ambient to 100C PID microprocessor controller touch pad type achieves accurate control. Memory to store three temperature setting and single button to activate required set temperature. Temperature unit display readout.
1 10000
(Note: Please note the terms and conditions mentioned below)
GOVERNMENT POLYTECHNIC, KHAMGAON
WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
Page 2 of 4
Page 2 of 4
TERMS AND CONDITIONS
The bid/quotation should be submitted in two bid format.( Technical bid & Commercial Bid)
The first envelope will contain Technical specifications of the product, technical literature
/ leaflet and other documents mentioned below. It is mandatory to the suppliers to submit
following documents without which your quotation will not be considered.
1. Covering Letter for tender on the company letter head mentioning official address, Contact
No, E-Mail address and website (if available) address.
2. Registration letter of supplier’s establishment (company / organization)
3. EMD in this regard (3% of the quoted cost or Re. 5000 whichever is minimum) to be paid
in the form of DD in favor of Principal, Govt. Polytechnic, Khamgaon OR Exemption
certificate from competent authorities, if exemption is claimed.
4. GST registration certificate / Number.
5. GST Clearance Certificate / GST Challan for last quarter of the financial year. (Paid up to
July 2018)
6. Authorization / Distributorship certificate from manufacturer. Proof of permission to
manufacture
7. The equipment / item mentioned in the quotation from competent authorities. (to be
submitted if the bidder is not a manufacturer)
8. Technical literature / leaflet of the make and model no of equipment quoted.
9. Undertaking by supplier confirming quality of Equipment / Machinery.
10. Under taking by supplier towards supply of equipment within prescribed date / period and
post sales services.
(Additional document may also be asked by undersigned for confirming the details.)
Page 3 of 4
Page 3 of 4
The second envelope will contain the financial bid in which the all inclusive rates F.O.R.
Destination will be written and signed with the stamp of the establishment in the following
format.
Sr.
No.
Name of the item with specification
Quantity
required
All
inclusive
cost per
unit
(Rs.)
All
inclusive
cost for
quantity
mentioned.
(Rs.)
Name of the
item Specifications
Date - (Signature)
Place - Rubber Stamp of Organization
Page 4 of 4
Page 4 of 4
Important Instructions
The two envelopes should be sealed with a mention of the type of envelope (technical /
Financial), Reference no., Date of opening the quotation on the front side of the envelope.
These two envelopes should be sealed in a third envelope by giving heading “Quotation for
supply of “Applied Mechanics Department Equipment” and writing complete address of the
undersigned. (Address: Principal, Government Polytechnic, Khamgaon, Jalamb Road,
Khamgaon, Dist: Buldana, (M.S.), Pin 444 303.
The quotations should reach the undersigned on or before date 02/01/2019
The material will be checked at this institute.
No extra charges will be paid for cartage, packing etc. for the material rejected and replaced.
Quotations will be opened at 3.00 AM/ PM on date 03/01/2019 at office of the Principal of
Institute.
Rates should be valid for 6 months from the date of confirmation letter.
Materials should be quoted for standard makes and minimum pkgs.
Delivery to the consignee has to be effected within 1 week from the date of issue of purchase
order or on or before the prescribed date. (if any)
The undersigned reserves the right to accept or reject any offer or all offers without assigning
any reason thereof.
The said process is subjected to the necessary approval from higher authorities.
Principal Govt. Polytechnic, Khamgaon.
Copy to:
1) Hon. Director, Directorate of Technical Education M. S. Mumbai for information please. It is requested to
do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information pleases. It is
requested to do needful for uploading the same on website as per instructions issued.
3) Head of Civil Departments for information and n a
4) Suppliers as list attached herewith
5) Shri. Ambatakar, Programmer, GP Khamgaon, for uploading on Institute website.
6) Institute Notice Board.
Page 1 of 4
Page 1 of 4
No.: GPK/EQP/inst purchase/EED/2018-19/3295 Date: 05/12/2018
By post / email
To,
……………………….
……………………….
………………………..
………………………..
QUOTATION
Sub: Quotation for purchase of equipment / furniture.
(Due Date 02/01/2019 & Date of Opening : 03/01/2019) Dear Sir,
Sealed Quotations are invited from eligible and interested manufacturers/ dealers/distributors/
for the following items on the terms and conditions mentioned below.
Sr.
No.
Name of the item with specification
Quantity
required
Approximate
cost per unit
(Inclusive of
GST) (Rs.)
Name of the item Specification
1 Wattmeter-3 Phase
Current-2.5 to 5 Amp.Voltage 50-100-
200-400 Voltage Circuit Resistance -150
ohm
Power 500-1500 watt. Continuous rating
2 8000
2 Current Transformer Operating voltage 230v AC,50Hz, Input
Power 3watt,Current Rating 5/1Amp. 3 2000
3 Potential Transformer 230 v,50Hz,8W type syn 144m,Burdon
10VA 4 2000
4 Megger Hand driver generator type, (crank to
turn) Metal Body 500 v,0-100 mega ohm 1 4000
5 Tong tester
Model having range 0-10-30-100-300-
1000A and 300/600volt having accuracy
+5%fsd complete with leather case,test
leads .
2 2000
6 LCR Meter Inductance -1micro henry to
10H,capacitance 05pf to 2 4000
GOVERNMENT POLYTECHNIC, KHAMGAON
WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
Page 2 of 4
Page 2 of 4
1000microfarad,Resistance-01 ohm to
10megaohm along with suitable signal
generator & detector.
7 Fuse protection kit Current range 5/10 amp,voltage 230 v ,
50Hz, single phase. 1 4000
8 Pure inductor-varaable Current range 0to 5amp.,50Hz,01 mh
to10mh. Iron core,single phase . 2 5000
9
Electric power drill
Machine-with
hammering
Power 380W, Speed0-2600 rpm 1 4000
(Note: Please note the terms and conditions mentioned below)
TERMS AND CONDITIONS
The bid/quotation should be submitted in two bid format.( Technical bid & Commercial Bid)
The first envelope will contain Technical specifications of the product, technical literature
/ leaflet and other documents mentioned below. It is mandatory to the suppliers to submit
following documents without which your quotation will not be considered.
1. Covering Letter for tender on the company letter head mentioning official address, Contact
No, E-Mail address and website (if available) address.
2. Registration letter of supplier’s establishment (company / organization)
3. EMD in this regard (3% of the quoted cost or Re. 5000 whichever is minimum) to be paid
in the form of DD in favour of Principal, Govt. Polytechnic, Khamgaon OR Exemption
certificate from competent authorities, if exemption is claimed.
4. GST registration certificate / Number.
5. GST Clearance Certificate / GST Challan for last quarter of the financial year. (Paid up to
July 2018)
6. Authorization / Distributorship certificate from manufacturer. Proof of permission to
manufacture
7. The equipment / item mentioned in the quotation from competent authorities. (to be
submitted if the bidder is not a manufacturer)
8. Technical literature / leaflet of the make and model no of equipment quoted.
9. Undertaking by supplier confirming quality of Equipment / Machinery.
10. Under taking by supplier towards supply of equipment within prescribed date / period and
post sales services.
(Additional document may also be asked by undersigned for confirming the details.)
Page 3 of 4
Page 3 of 4
The second envelope will contain the financial bid in which the all inclusive rates F.O.R.
Destination will be written and signed with the stamp of the establishment in the following
format.
Sr.
No.
Name of the item with specification
Quantity
required
All
inclusive
cost per
unit
(Rs.)
All
inclusive
cost for
quantity
mentioned.
(Rs.)
Name of the
item Specifications
Date - (Signature)
Place - Rubber Stamp of Organization
Page 4 of 4
Page 4 of 4
Important Instructions
The two envelopes should be sealed with a mention of the type of envelope (technical /
Financial), Reference no., Date of opening the quotation on the front side of the envelope.
These two envelopes should be sealed in a third envelope by giving heading “Quotation for
supply of “Electrical Engg. Department Equipment” and writing complete address of the
undersigned. (Address: Principal, Government Polytechnic, Khamgaon, Jalamb Road,
Khamgaon, Dist: Buldana, (M.S.), Pin 444 303.
The quotations should reach the undersigned on or before date 02/01/2019
The material will be checked at this institute.
No extra charges will be paid for cartage, packing etc. for the material rejected and replaced.
Quotations will be opened at 3.00 AM/ PM on date 03/01/2019 at office of the Principal of
Institute.
Rates should be valid for 6 months from the date of confirmation letter.
Materials should be quoted for standard makes and minimum pkgs.
Delivery to the consignee has to be effected within 1 week from the date of issue of purchase
order or on or before the prescribed date. (if any)
The undersigned reserves the right to accept or reject any offer or all offers without assigning
any reason thereof.
The said process is subjected to the necessary approval from higher authorities.
Principal Govt. Polytechnic, Khamgaon.
Copy to:
1) Hon. Director, Directorate of Technical Education M. S. Mumbai for information please. It is requested to
do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information pleases. It is
requested to do needful for uploading the same on website as per instructions issued.
3) Head of Electrical Engineering Departments for information and n a. Please verify specifications and
approximate cost
4) Suppliers as list attached herewith
5) Shri. Ambatakar, Programmer, GP Khamgaon, for uploading on Institute website.
6) Institute Notice Board
Page 1 of 6
No.: GPK/EQP/inst purchase/MED/2018-19/3296 Date: 05/12/2018
By post / email
To,
……………………….
……………………….
………………………..
………………………..
QUOTATION
Sub: Quotation for purchase of equipment / furniture.
(Due Date 02/01/2019 & Date of Opening : 03/01/2019) Dear Sir,
Sealed Quotations are invited from eligible and interested manufacturers/ dealers/distributors/ for the following items on the terms and conditions mentioned below.
Sr. No.
Name of the item with specification Quantity required
Approximate cost per unit (Inclusive of GST) (Rs.)
Name of the item Specification
1 Mcleod Gauge
Mcleod Gauge Test Ring ,
Range 0 to 50 microns
accuracy - + 0.05%, Liquid
charge – Approximately 100
to 120 CC including 6 CC of
mercury
1 46000
2 Bernolli’s Theorem Application
Manometer Range 0-400 MN,
No of Manometric Tube 07,
Test Length : 200 MN circular,
acrylic Bar Upstream Size : 35
MN Dia Throat Diameter 22
MN DIA.
1 24000
3 Cut Section Model of Hermetically Sealed Compressor
Cut Section Model of
Hermetically sealed
Compressor cut section model
of standard size used in
technical education systems
1 6000
4 Cut Section Model of Split Air-Conditioner
Cut section model of split air
conditioner Cut section model
of standard size used in
technical education systems.
1 8000
5 Stroboscope
Stroboscope Display 5 digits,
circuit exclusive one chip
design microprocessor, unit of
1 18000
GOVERNMENT POLYTECHNIC, KHAMGAON
WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
Page 2 of 6
measurement FPM, Operating
temperature 0 to 500 C,
Operating Humidity – Less
than 80 % RH Power Supply
AC (100 to 240V) & DC (9V)
with adapter of 3A Battery –
DC 1.2 V NI-MH Built Up
with chargeable unit , Flash
Tube – Replaceable of xenon
lamp Stroboscope flash rate
100 to 15000 flashes per
minute. Flash duration 60 To
1000 Microseconds accuracy -
+ 0.05% resolution 0.1
FRM/RPM
6 Temperature Trainer Kit
Temperature Trainer Kit
trainer kit consisting of
bimetallic strip, thermometer,
thermistor & Thermocouple
1 20000
7 Pyrometer
Pyrometer, Temperature range
: -40 to 9000C, Temperature
reolution – 0,10C spectral
range – 8 to 14 uM, optical
revolution- 0.10C, Spectral
Range 8 to 14 uM, Optical
resolution – 22:1, System
Accuracy - +10C, Response
time – 150 MS, Power Supply
8 to 30 V DC with maximum
current 100 MA relative
humidity : 10- 95% Non-
condensing..
1 10000
8 Strain gauge trainer (strain/force measurement)
Net dimensions (assembled):
720 mm high x 760 mm wide x
520 mm front to back
Net weight (including Strain
Display and Weight Sets): 27.5
kg
Packed weight: 41.5 kg
Packed volume: 0.16 m3
Sets of masses: The large mass
set gives weights from 0.5 kg
to 10 kg in a range of units.
The small mass set gives
weights from 10 g to 500 g in
10 g units.
Dummy resistors: Set of three
plugs fi tted with high
accuracy resistors that match
the strain gauges
Electrical supply: 100 VAC
to 240 VAC, 50 Hz to 60 Hz
2 10000
Page 3 of 6
with earth
Strain display: Multiline
display that shows:
• Bridge output voltage (micro-
volt)
• Strain reading in micro-strain
(me)
• Active arms (gauges)
• Gauge factor
Strain systems:
• Bending system: Four
standard gauges fi tted to a
given datum on a steel beam, fi
xed as a cantilever. Nominal
beam cross-section is 5 mm x
20 mm.
• Torsion system: Two sets of
identical 45-degree shear/
torque strain gauge rosettes fi
tted to a torsion bar. Nominal
bar diameter is 10 mm.
• Tension system: Two sets of
identical 90-degree ‘Tee’ strain
gauge rosettes fi tted to a
tensile test specimen. Steel
specimen supplied as standard.
Nominal tension specimen
cross-section is 2 mm x 10
mm.
9 Rotameter trainer for flow measurement
2 10000
10 Temperature measurement and control using thermocouple kit
Model UITM-151 [U-tube
Manometer Sensor]
UITM-152
[Differential Pressure Sensor]
Orifice:
Orifice plate embedded
between two metal
tubings.
UITM-151-U tube
manometer with
Mercury filled.
UITM-152-Differential
type piezo resistive
pressure sensor.
Flow Rate: 60 to 600 LPM
Rotameter : 60 to 1700 LPM
Acrylic body. Rotameter for
known flow measurement.
Pump: FHP Manoblock.
Water Tank : SS tank of
capacity 25 liters for water
storage and circulation for
UITM-152
Display : 3½ digit to
2 12500
Page 4 of 6
read ±1999 counts.
Power Supply: 230V ± 10%
@50 Hz
Inductance : Copper wire
wound on a babin with MS
core moving inside.
Displacement: 20mm
Power Supply: Necessary
cable provide
Accessories: Aluminium
Housing with core moving on
a graduated scale
11 Flow measurement using optical transducer
2 12500
(Note: Please note the terms and conditions mentioned below)
Page 5 of 6
TERMS AND CONDITIONS
The bid/quotation should be submitted in two bid format.( Technical bid & Commercial Bid)
The first envelope will contain Technical specifications of the product, technical literature
/ leaflet and other documents mentioned below. It is mandatory to the suppliers to submit
following documents without which your quotation will not be considered.
1. Covering Letter for tender on the company letter head mentioning official address, Contact
No, E-Mail address and website (if available) address.
2. Registration letter of supplier’s establishment (company / organization)
3. EMD in this regard (3% of the quoted cost or Re. 5000 whichever is minimum) to be paid
in the form of DD in favour of Principal, Govt. Polytechnic, Khamgaon OR Exemption
certificate from competent authorities, if exemption is claimed.
4. GST registration certificate / Number.
5. GST Clearance Certificate / GST Challan for last quarter of the financial year. (Paid up to
July 2018)
6. Authorization / Distributorship certificate from manufacturer. Proof of permission to
manufacture
7. The equipment / item mentioned in the quotation from competent authorities. (to be
submitted if the bidder is not a manufacturer)
8. Technical literature / leaflet of the make and model no of equipment quoted.
9. Undertaking by supplier confirming quality of Equipment / Machinery.
10. Under taking by supplier towards supply of equipment within prescribed date / period and
post sales services.
(Additional document may also be asked by undersigned for confirming the details.)
The second envelope will contain the financial bid in which the all inclusive rates F.O.R.
Destination will be written and signed with the stamp of the establishment in the following
format.
Sr.
No.
Name of the item with specification
Quantity
required
All
inclusive
cost per
unit
(Rs.)
All
inclusive
cost for
quantity
mentioned.
(Rs.)
Name of the
item Specifications
Date - (Signature)
Place - Rubber Stamp of Organization
Page 6 of 6
Important Instructions
The two envelopes should be sealed with a mention of the type of envelope (technical /
Financial), Reference no., Date of opening the quotation on the front side of the
envelope. These two envelopes should be sealed in a third envelope by giving heading
“Quotation for supply of “Mechanical Engg. Department Equipment” and writing
complete address of the undersigned. (Address: Principal, Government Polytechnic,
Khamgaon, Jalamb Road, Khamgaon, Dist: Buldana, (M.S.), Pin 444 303.
The quotations should reach the undersigned on or before date 02/01/2019
The material will be checked at this institute.
No extra charges will be paid for cartage, packing etc. for the material rejected and
replaced.
Quotations will be opened at 3.00 AM/ PM on date 03/01/2019 at office of the Principal
of Institute.
Rates should be valid for 6 months from the date of confirmation letter.
Materials should be quoted for standard makes and minimum pkgs.
Delivery to the consignee has to be effected within 1 week from the date of issue of
purchase order or on or before the prescribed date. (if any)
The undersigned reserves the right to accept or reject any offer or all offers without
assigning any reason thereof.
The said process is subjected to the necessary approval from higher authorities.
Principal Govt. Polytechnic, Khamgaon.
Copy to:
1) Hon. Director, Directorate of Technical Education M. S. Mumbai for information please. It is
requested to do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information pleases.
It is requested to do needful for uploading the same on website as per instructions issued.
3) Head of Mechanical engineering Department for information and n a . Verify specification and
cost of items.
4) Suppliers as list attached herewith
5) Shri. Ambatakar, Programmer, GP Khamgaon, for uploading on Institute website.
6) Institute Notice Board.
Page 1 of 5
No. : GPK/EQP/inst purchase/CED_List-A/2018-19/3257 Date: 01/12/2018
By post / email
To,
……………………….
……………………….
………………………..
………………………..
QUOTATION
Sub: Quotation for purchase of equipment / furniture.
(Due Date 02/01/2019 & Date of Opening: 03/01/2019) Dear Sir,
Sealed Quotations are invited from eligible and interested manufacturers/ dealers/distributors/
for the following items on the terms and conditions mentioned below.
Sr. No.
Name of the item with specification Quantity required
Approximate cost per unit ( Inclusive of
GST) (Rs.) Name of the item Specification
1 Digital PH Meter
Major Group =030
Minor Group =032
PH Range= 0 To 14 PH
Accuracy= 0.01 PH
Resolution 0.01PH
Reproductibility 0.01 PH
Power Supply = 230v
02 7000
2 Digital DO Meter Standard 01 7000
3 Electronic Digital
Balance Set
2 kg Capacity
Accuracy :1mg 01 20000
4 Hot Air Oven
Suitable to operate on 220/230V, AC
with digital temperature control by
thermostat in the heating range from
50°C to 250°C.
01 15000
5 COD Reflux Apparatus Complete test set with hot plate 02 10000
6 Jar Test Apparatus
Suitable to operate on 220/230V,
mechanically operated six paddles
having flocculator geared with heavy
duty 1/20 HP motor having variable
speed from 10 to 120 rpm with built
in speed control and illuminated
base.
01 20000
7 Thickness Gauge containing openings for aggregates 01 2000
GOVERNMENT POLYTECHNIC, KHAMGAON
WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
Page 2 of 5
sizes 63, 50, 40, 31.5, 25, 20, 16,
12.5, 10, & 6.3 mm as per IS:2386
(Part-1)-1963.
8 Length Gauge
containing openings for aggregates
sizes 63, 50, 40, 31.5, 25, 20, 16,
12.5, 10, & 6.3 mm as per IS:2386
(Part-1)-1963.
01 2000
9
Pensky Marten's Flash &
Fire Point Test (For
Bitumen
Apparatus 100x200x240 mm with
measurement range 0-95 as per IS:
1209-1953.
01 6000
10 Ductility Testing Machine
(For Bitumen)
With ductility mould & base plate.
01 7000
11 Digital Turbidity Meter 3 ½ Digit LED Display
Range up to 1000NTU/JTO 01 7500
12 Chloroscope
Standard having range 0.0-5.0 ppm
with Colorimetric Sensitivity 0.1ppm
and indicator solution.
03 1500
13 Digital Portable Water
Testing Kit: Standard 01 15000
14 Metric Chain – 30m
Length
(Metric Chain consisting of a fixed
number of straight links of
galvanized mild steel wire 4mm.in
diameter. The end of each link are
bent into a loop and connected
together by means of three circular
shape rings. The joints of the rings
may be open or welded preferably
welded. The ends of the chain are
provided with brass handles. The
handle is linked with a swivel joint to
the chain. The length of each link is
200 mm. Each meter is provided
with circular brass ring & each five
meter length is provided with brass
tallies of requisite shapes Each
chain should be provided with 10
nos. of M.S. Arrows of 4 mm
diameter bar and 40 cm. Height.as
per: IS 1492 -1970)
03 3000
15 Prismatic Compass
Made of Gun / Nonmagnetic Metal in
a leather case/plastic with teak wood
/aluminum tripod Stand. Size of
compass 80-110 mm. diameter.
02 2500
16 Dumpy level
200-300 mm, internal focusing
telescope with 200 meters focusing
range, with erect image and desired
magnification.
02 7000
17 Leveling Staff Made of Aluminum body Telescopic
in 3 PCS, 4 meter in length packed 02 1500
Page 3 of 5
in canvas cover, graduated in
meters, dm, cm and mm with white
background and black strips. 5mm
thick with suitable locking
arrangement.
18 Transit Theodolite
Direct reading vernier Transit
theodolite 127 mm / 178 mm, export
quality fitted with / without Optical
Plummate arrangement, showing
erect image with Horizontal &
Vertical circles containing main
scales & vernier in stainless steel /
Pure silver / Suitable metal along
with trough or tubular compass with
suitable attachment and accessories
in wooden /metal box with telescopic
aluminum / wooden stand & 20/10
sec. accuracy.
02 12000
(Note: Please note the terms and conditions mentioned below)
Page 4 of 5
TERMS AND CONDITIONS
The bid/quotation should be submitted in two bid format.( Technical bid & Commercial Bid)
The first envelope will contain Technical specifications of the product, technical literature / leaflet
and other documents mentioned below. It is mandatory to the suppliers to submit following documents
without which your quotation will not be considered.
1. Covering Letter for tender on the company letter head mentioning official address, Contact No, E-
Mail address and website (if available) address.
2. Registration letter of supplier’s establishment (company / organization)
3. EMD in this regard (3% of the quoted cost or Re. 5000 whichever is minimum) to be paid in the
form of DD in favour of Principal, Govt. Polytechnic, Khamgaon OR Exemption certificate from
competent authorities, if exemption is claimed.
4. GST registration certificate / Number.
5. GST Clearance Certificate / GST Challan for last quarter of the financial year. (Paid up to July
2018)
6. Authorization / Distributorship certificate from manufacturer. Proof of permission to manufacture
7. The equipment / item mentioned in the quotation from competent authorities. (to be submitted if the
bidder is not a manufacturer)
8. Technical literature / leaflet of the make and model no of equipment quoted.
9. Undertaking by supplier confirming quality of Equipment / Machinery.
10. Under taking by supplier towards supply of equipment within prescribed date / period and post sales
services.
(Additional document may also be asked by undersigned for confirming the details.)
The second envelope will contain the financial bid in which the all inclusive rates F.O.R. Destination
will be written and signed with the stamp of the establishment in the following format.
Sr.
No.
Name of the item with specification
Quantity
required
All
inclusive
cost per
unit
(Rs.)
All
inclusive
cost for
quantity
mentioned.
(Rs.)
Name of the
item Specifications
Date - (Signature)
Place - Rubber Stamp of Organization
Page 5 of 5
Important Instructions
The two envelopes should be sealed with a mention of the type of envelope (technical /
Financial), Reference no., Date of opening the quotation on the front side of the envelope.
These two envelopes should be sealed in a third envelope by giving heading “Quotation for
supply of “Civil Engg. Department Equipment” and writing complete address of the
undersigned. (Address: Principal, Government Polytechnic, Khamgaon, Jalamb Road,
Khamgaon, Dist: Buldana, (M.S.), Pin 444 303.
The quotations should reach the undersigned on or before date 02/01/2019
The material will be checked at this institute.
No extra charges will be paid for cartage, packing etc. for the material rejected and replaced.
Quotations will be opened at 3.00 AM/ PM on date 03/01/2019 at office of the Principal of
Institute.
Rates should be valid for 6 months from the date of confirmation letter.
Materials should be quoted for standard makes and minimum pkgs.
Delivery to the consignee has to be effected within 1 week from the date of issue of purchase
order or on or before the prescribed date. (if any)
The undersigned reserves the right to accept or reject any offer or all offers without assigning
any reason thereof.
The said process is subjected to the necessary approval from higher authorities.
Principal Govt. Polytechnic, Khamgaon.
Copy to:
1) Hon. Director, Directorate of Technical Education M. S. Mumbai for information please. It is requested to
do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information pleases. It is
requested to do needful for uploading the same on website as per instructions issued.
3) Head of Civil Departments for information.
4) Suppliers as list attached herewith
5) Shri. Ambatakar, Programmer, GP Khamgaon, for uploading on Institute website.
6) Institute Notice Board.