GLUE - laver.co.uk · Mark position of final piece sym-metrically over doorway. Cut panels and fix....
2
wall panelling For nearest stockists T. 07852 770022 www.aquamura.co.uk Distributed by Features A design-led selection of Continental laminate finishes Easy to install - no wet trades Cost-effective Hard-wearing Easily cleaned and maintained Applications Aquamura has been successfully installed in all of the following locations: Bathrooms Doctors’ surgeries Fast food restaurants Changing rooms Gymnasiums and Health Clubs Reception areas Pubs, Clubs and Bars Schools Hospitals and Health Centres Retail areas Shower cubicles Leisure Centres Heavy-traffic corridors Kitchens Specification Core material Birch plywood Face material High pressure decorative laminate Reverse Balancing laminate Dimensions Standard panel size 2400 x 590 x 11mm T&G 12kg Shower panel size 2400 x 1200 x 11mm square cut 24kg Shower panel special 2400 x 1200 x 11 mm T&G 24kg Fire Performance Aquamura complies with Class II surface spread of flame. Cleaning and Maintenance Wipe with a non-abrasive damp cloth and a mild spray detergent. Warranty Aquamura is guaranteed for 10 years if correctly fitted, thoroughly sealed and maintained. Note: The colours reproduced in this brochure are as close as possible to the actual laminates. It is recommended that you obtain samples prior to final specification. Aquamura is a wall panelling system, made from WBP Birch plywood faced in a high-pressure decorative laminate. It is a simple, attractive and economical way to transform walls. In a complete room installation, the tongued and grooved laminate-faced panels fit together quickly and effortlessly. The fixings are completely hidden. Within a shower enclosure, full size boards clad each wall, minimising joints, for a hygienic solution, and no mouldy grout! Technical information - Fitting standard panels What is Aquamura? Aquamura panels have an attractive, tough laminate surface, and are constructed from quality water resistant plywood. For best results with Aquamura panels, start in corner and finish over doorway. Glue down edge of panel and fix into corner profile. Screw down length of grooved panel. Use appropriate plugs for concrete, brick or plaster. Apply sealant in joint before fitting next panel. Slide the panel into place. Cut last panel of each wall to size. Glue edge, fit profile and swing into place. Mark position of final piece sym- metrically over doorway. Cut panels and fix. Glue and screw where heads will be hidden by door moulding or coving. Fixing shower panels Shower panels should be trimmed to the correct height and width and then installed resting on the shower tray, embedded in silicon. Panels can be glued back to wall battens or glued directly onto a suitable wall. Aluminium internal corner jointers and end caps are recommended, with silicon applied into the extrusion. Accessories Aluminium jointing sections are available in 2500mm lengths in a variety of finishes: S.A.A., polished aluminium, black and white. 1 5 DOORWAY 2 6 3 7 4 GLUE 8 Internal External Continuous End cap profile profile profile
Transcript of GLUE - laver.co.uk · Mark position of final piece sym-metrically over doorway. Cut panels and fix....
wall panelling
For nearest stockists T. 07852 770022 www.aquamura.co.uk
Distributed by
FeaturesA design-led selection of Continental laminate finishes Easy to install - no wet tradesCost-effective Hard-wearingEasily cleaned and maintained
ApplicationsAquamura has been successfully installed in all of the following locations:Bathrooms Doctors’ surgeriesFast food restaurants Changing roomsGymnasiums and Health Clubs Reception areasPubs, Clubs and Bars SchoolsHospitals and Health Centres Retail areasShower cubicles Leisure CentresHeavy-traffic corridors Kitchens
SpecificationCore material Birch plywoodFace material High pressure decorative laminateReverse Balancing laminate
DimensionsStandard panel size 2400 x 590 x 11mm T&G 12kgShower panel size 2400 x 1200 x 11mm square cut 24kgShower panel special 2400 x 1200 x 11 mm T&G 24kg
Fire PerformanceAquamura complies with Class II surface spread of flame.
Cleaning and MaintenanceWipe with a non-abrasive damp cloth and a mild spray detergent.
WarrantyAquamura is guaranteed for 10 years if correctly fitted, thoroughly sealed and maintained.
Note: The colours reproduced in this brochure are as close as possible to the actual laminates. It is recommended that you obtain samples prior to final specification.
Aquamura is a wall panelling system, made from WBP Birch plywood faced in a high-pressure decorative laminate. It is a simple, attractive and economical way to transform walls.
In a complete room installation, the tongued and grooved laminate-faced panels fit together quickly and effortlessly. The fixings are completely hidden.
Within a shower enclosure, full size boards clad each wall, minimising joints, for a hygienic solution, and no mouldy grout!
Technical information - Fitting standard panelsWhat is Aquamura?
Aquamura panels have an attractive, tough laminate surface, and are constructed from quality water resistant plywood.
For best results with Aquamura panels, start in corner and finish over doorway.
Glue down edge of panel and fix into corner profile.
Screw down length of grooved panel. Use appropriate plugs for concrete, brick or plaster.
Apply sealant in joint before fitting next panel.
Slide the panel into place. Cut last panel of each wall to size. Glue edge, fit profile and swing into place.
Mark position of final piece sym-metrically over doorway. Cut panels and fix. Glue and screw where heads will be hidden by door moulding or coving.
Fixing shower panelsShower panels should be trimmed to the correct height and width and then installed resting on the shower tray, embedded in silicon.
Panels can be glued back to wall battens or glued directly onto a suitable wall. Aluminium internal corner jointers and end caps are recommended, with silicon applied into the extrusion.
AccessoriesAluminium jointing sections are available in 2500mm lengths in a variety of finishes: S.A.A., polished aluminium, black and white.
1
5
DOORWAY
2
6
3
7
4
GLUE
8
Internal External Continuous End capprofile profile profile
DAS Aquamura 6pp 2016 v3.indd 1-3 04/01/2017 14:48
TrAverTIne gloSS (gloss)
FroSTWood (gloss)
MoccA grAIn (gloss)
cArrerA (gloss) large scale
geSSo (gloss) BreccIA gloSS (gloss)
reSA (gloss)
MIrAge (gloss)SunrISe (gloss)
nIghT gAlAxy (gloss)Ice gAlAxy (gloss) ShIMMer (gloss)
lunA STone (Stone)
SuPernovA (gloss)
TrAverTIne STone (Stone) SAnd STone (Stone)
onyx (gloss)
BreccIA SlATe (Slate)Bruno (gloss)
BeAch huT (grain )
PeArl MArBle (gloss)
BlIzzArd (gloss)
doloMITe (gloss)
lATTe SlATe (Slate)
cAPPuccIno SlATe (Slate)
Metallic & Stone Effects Collection
Whi
te C
olle
ctio
n
Earth
Col
lect
ion
Neo
n C
olle
ctio
n
BIAnco (Matt)
lucIdo (gloss)
Azure (gloss)
Berry (gloss)
lIMe (gloss)
DAS Aquamura 6pp 2016 v3.indd 4-6 04/01/2017 14:49
