8/12/2019 Glove Spec

1/2

0333

ELECTRICAL INSULATING GLOVES

INSTRUCTIONS FOR USE

Range Available: sizes and codes

Size 8 9 10 11

Class 00 RE00360/08 RE00360/09 RE00360/10 RE00360/11

Class 0 RE0360/08 RE0360/09 RE0360/10 RE0360/11

Class 1 RE1360/08 RE1360/09 RE1360/10 RE1360/11

Class 2 RE2360/08 RE2360/09 RE2360/10 RE2360/11

Class 3 RE3360/08 RE3360/09 RE3360/10 RE3360/11

EC type examination carried out by: APAVE - 13-17 rue Salneuve 75854 Paris Cedex 17 (France).

Notified Body number 0077Manufacturer certified ISO-9001 by : AFAQ - 116 avenue A.Briand - 92224 Bagneux Cedex (France).

Notified body number 0033

STORAGE & TRANSPORT:

Keep away from direct heat or light sources and store in temperatures between 10 and 21c, humidity 60+/-10%.Do not crush or fold the gloves. The gloves should be kept in their original packaging or in an electricians bagwhen not in use.

BEFORE USE:

Inflate the gloves with air in order to detect potential faults. Carry out a thorough visual inspection.

PRECAUTIONS:

Avoid contact with petrols, oils, grease, acids or any corrosive products.Do not use the gloves if wet.

CARE:

To get the best service from these gloves ensure that after use all contaminant is removedWash the gloves with soap and water. Do not dry at temperatures above 65c

CAUTION:

The life of these gloves, whether used or in storage is limited.The standard EN60903:2003 recommends a periodic inspection, electric retesting or periodic replacement

THESE GLOVES ARE DESIGNED TO BE USED

EXCLUSIVELY FOR ELECTRICAL PURPOSE

You are advised to retain this packaging for future reference

The life of gloves when they are stored or used is limited. The standards EN60903:2003and IEC60903:2002 indicate in Annex E that : No

gloves of classes 1,2 & 3, not even those held in storage, should be used unless they have been tested within a maximum period of six

months.The tests consist of air inflation to check for air leaks, a visual inspection while pressurised, and then a routine dielectric test.

For Class 00 and Class 0, a check for air leaks and visual inspection may be considered adequate. However a routine dielectric test may beperformed at the users request.

All gloves have a straight cuff.

Also avai lable : leather over gloves grey leather gloves w ith a c hrom e leather safety c uff and nylon

tension strap on the back of the hand to adjust the f i t . Designed to be worn over the electr ic ian gloves to

protect i t from mechanical r isks.

Regeltex-2005

BM Polyco Ltd, Great CambridgeIndustrial Estate,Lincoln Road, Enfield, EN1 1SH. UK.www.superglove.co.uk

8/12/2019 Glove Spec

2/2

PROTECTION LEVELS & ELECTRICAL REQUIREMENTS:

Routine test: The proof test voltage is applied for one minute. During the test, no puncture can occur. The leakagecurrent (reduced by 2mA) can not exceed the value indicated in the table below.Sampling test: After conditioning for 16 hours in water for moisture absorption, the proof test voltage is applied forthree minutes, then the withstand voltage is reached and immediately reduced. The test is considered a successif no puncture occurs and if the leakage current does not exceed the values specified in the table below.The sampling test (without moisture absorption) is also done after:ageing, ozone conditioning, Oil conditioning, acid conditioning and very low temperature conditioning

Class

Test Voltage

Working Voltage

Length

Sizes

00

2500v

500v

360mm

8,9,10,11

0

5000v

1000v

360mm

8,9,10,11

1

10000v

7500v

360mm

8,9,10,11

2

20000v

17000v

360mm

8,9,10,11

3

30000v

26500v

360mm

8,9,10,11

Max proof testcurrent (mA rms)

14 14 16 18 20

Withstand testvoltage (kV rms)

5000v 10000v 20000v 30000v 40000v

GLOVE MARKING - INFORMATION

CLASS 00/AZC

XX / YY

LOT XXXX 0333

EN 60903:2003 IEC 60903:2002

SIZE 10

REG

MECHANICAL REQUIREMENTS:

Minimum

value

Ageing

(168hrs @ 70c)

Immersion in 32 B

Sulphuric acid for 8hrs

Immersion in liquid 102 at

70c for 24hrs

Tensile strength 16MPa

Elongation at break 600% > 80% of unaged values

Not less than 75% of theinitial value

Not less than 75% of theinitial value

Tension set 15% max 15% max

Puncture resistance 18N/mm

CATEGORIES:

A : Acid H : Oil Z : Ozone C : very low temperature R = A + H + Z

Marking of periodic Inspection date

Mandatory

Identification of Manufacturer

Standards references

Marking of datehen first used

Size

Class category

Month and year of production