Gesamt-Katalog Edition 2006
Click here to load reader
-
Upload
daniel-timis -
Category
Documents
-
view
149 -
download
24
description
Transcript of Gesamt-Katalog Edition 2006
-
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S00
-
Technische Daten / :Specification
* Bestellbeispiel / : 22513 / HS-UT 050-10 / 60 HubOrder Example
Ident-Nr.
Code No.
Bezeichnung:
Description:
Arbeitsflche / (BxH):Einbau / :Schieber / :Presskraft / (min.):
hhebreite
(Details siehe Diagramm / )
Working AreaClosed Height
Cam Unit WidthPress Force
For details see diagramm
Horizontalschieber /Baugre / : HS-UT 050-0 bis / 20
Horizontal CamType to
50 mm x 70 mm210 mm (175 mm - 0)50 mm6 to
22511 HS-UT 050-0 60
22512 HS-UT 050-5 60
22513 HS-UT 050-10 60
22514 HS-UT 050-15 60
22515 HS-UT 050-20 60
Hub
Stroke
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S01
-
3D Ansicht3D View
AblaufdiagrammCam Diagram
Draufsicht TreiberPlan View Cam Driver
Ansicht XView X
Schnitt A-ASection A-A
Draufsicht Schieberfhrung / Plan View Cam Base
Achtung !Bei 0 ohne Adapterplatte
Attention !
At 0 without Adapter Plate
Rd. 8H7 (2x)
Rd. 8H7 (2x)
Draufsicht Adapterplatte /(5-20)
Plan View Adapter Plate
Auf Zugnglichkeit derSchrauben und Stifte achten!
Verschraubung M8 (3x)
Take care for free accessto screws and dowels!
Screw Connection
Verschraubung
Auf Zugnglichkeit derSchrauben und Stifte achten!
M8 (4x)Screw Connection
Take care for free access toscrews and dowels!
A A
Konstruktions-EinfgepunktTooling-Ball
ArbeitsflcheWorking Area
Bau
hhe
/C
lose
d H
eigh
t
X
Hub +2Stroke +2
FestsetzmaFix Measure
Gasdruckfederweg = HubGasspringway = Stroke
Rd. 8H7 (2x)
Auf Zugnglichkeit derSchrauben und Stifte achten!
Verschraubung M8 (4x)
Take care for free accessto screws and dowels!
Screw Connection
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S02
-
Mae / Measures
FestsetzmaFix Measure
Bauhhe / 0,5Closed Height
Retractility
Ident-Nr.Code No.
Cam Angle
GasdruckfederwegGas Spring Way
Abstreifkraft
HubStroke
Schieberwinkel
Fr geringere Rckzugskrfte (z.B.:beim Einsatz eines separatenAbstreifers auf dem Schieber) istes empfehlenswert, den Druck derGasdruckfeder zur Schonung derPresse oder Minimierung dere las t i schen Ver fo rmung imWerkzeugguss zu reduzieren(min.18 bar).
For lower retraction forces (forexample when a separate stripperis mounted on the cam) it isrecommandable to reduce the gasspring pressure (min. 18 bar) inorder to spare the press orminimize the elastic deformation inthe tool cast.
GewichtWeight
F0 / F1 (KN): 0,9 / 1,1
Presskraft Gasdruckfeder:Gas Spring Force
F0: Anfangskraft /F1: Endkraft /
starting forceending force
Alle nicht tolerierten Mae entsprechen ISO 2768 Mittel. Dimensions without tolerance are analog to ISO 2768 middle.
Stiftlcher werden mit 0,02mm Toleranz gefertigt. Dowel holes will be manufactured with 0,02mm tolerance.
0 5 10 15 20
175 210 210 210 210
+ 0,06+ 0,04+ 0,06+ 0,04
1611 14 15 15
35
64 64 64 64 64
50 45 40 40
64,16 60,0
~ T 10,0
X 71,51 65,0 60,0
21,6 31,9
32 32
150,8 140,5
44,7 57,0
~ S 140,0 170,6 160,8
R 32 32 32
155 150
P 50
Q 160 165 165
40 35
30 30
20 25
25 30
O 45 35 30
N - 30 30
150 150
M2 135
M3 150 150 150
135 135
185 190
65 65
135 135
M1 65 65 65
M - 170 180
20 20
L1 -
L2 20 20 20
- -
5 5
5 -
- 5
L - 25 15
K2 5 5 5
0-
K1 - - - 10
K - 20 10
22
22 22 22 22 22
- 22 22 22
89 94
I1 0,02 88 88 88 88 88
I 0,02 - 74 84
90100 80
H 45 45 45 45 45
G 120 108
195 200
E 40
F 175 183 190
32 25
50 50
120 115
15 5
D 0,02 95 130 125
C2 0,02 50 50 50
C1 0,02 30 30 30
160
10 15
30 30
40 40
B 35 25 20
C 0,02 40 40 40
60
A 0,02 170 175 180 165
60
60
0 5 10 15 20
60 60 60
22515
60
0,9 1,0 0,9 0,9 0,9
60 60 60
22511 22512 22513 22514
J
J1
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S03
-
Fhrungsklammer (L)Side Plate (L)
Fhrungsklammer (R)Side Plate (R)
AufnahmeplatteMounting Plate
SchieberfhrungCam Base
GasdruckfederGas Spring
Adapterplatte
(5-20)Adapter Plate
GleitplatteWear Plate
Zwangsrckholer (L)Positive Return (L)
PassfederFitting Key
Bauteile / Components
AnschlagbolzenStop Bolt
DmpferDampingElement
HalteplatteStop Plate
Zwangsrckholer (R)Positive Return (R)
TreiberCam Driver
SchieberCam Slider
Lock Out StiftLock Out Pin
Passfeder
(5-20)Fitting Key
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S04
-
Stckliste / Component Parts
Damping Element
Positive Return (R)
Positive Return (L)
Gas Spring Ejector
Side Plate (L)
Side Plate (R)
Cam Base
Cam Slider
Cam Driver
Description Material
Code No.
Stop Plate
Wear Plate
Adapter Plate
Fitting Key
Mounting Plate
Stop Bolt
Es ist darauf zu achten, dass der Schraubverschluss derGasdruckfeder unbedingt vor Inbetriebnahmeeingeschraubt und zustzlich eingeklebt werden muss!
It is important to ensure that the Screw Lock of the GasSpring is screwed in and secured with Loctite (or similar)before use!
Die Gewhrleistung erstreckt sich nur auf die kompletteSchiebereinheit.
The warranty is only extended to the complete cam unit.
Lieferumfang:Schiebereinheit, Pafedern, Lock Out - System
Scope of delivery:Cam unit, Fitting Keys, Lock Out - System
Ident-Nr.
Bezeichnung Material
Treiber
Schieber
Schieberfhrung
Anschlagbolzen
Gasdruckfeder
Aufnahmeplatte
Fhrungsklammer (L)
Fhrungsklammer (R)
Halteplatte
Dmpfer
Gleitplatte
Zwangsrckholer (L)
Zwangsrckholer (R)
Adapterplatte
Passfeder104225 1042251.0503.07 104225 104225 104225
1.7225 - 104224 104226
101498 101498 101498
WF 750/1A 18222 18222 18222 18221 18221
PUR
104220 104220
1.7225 103993 103993 103993 103993 103993
1.7225 104220 104220 104220
104219 104219
105842
104219 104219
101544 101544
105842 105842
21304 21304
1.7225 104042 104042 104042 104042 104042
WF 750/1A 21304 21304 21304
20
1.7225 104218 104223 104227 104229 104232
0 5 10 15
22511 22512 22513 22514
1.7225 105852 105851 105850
DADCO 101544 101544
1.7225 104219
1.7225 105842 105842
101498 101498
1.7225 104047
1.7225
22515
105849 105848
101544
104047 104047
104046 104046 104046
104228 104231
104047 104047
104046 104046
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S05
-
Lock Out Stift um Festsetzen des Schiebers verwenden!z
(nicht im Lieferumfang / )Use Lock Out Pin to lock the Cam!
not in scope of delivery
Lock Out Stift(nicht im Lieferumfang)Lock Out Pin(not in scope of delivery)
SchieberCam Slider
TreiberCam Driver
Gasdruckfeder SchlauchsystemGas Spring Linking Gasdruckfeder
Gas Spring
Anschluss Adapter (2x)Port Adapter
SchlauchHose
Kontrollarmatur (1x)Mini Control Panel (1x)
Schlauch Adapter (2x)Hose Adapter (2x)
Lock Out - System
SchieberfhrungCam Base
AufnahmeplatteMounting Plate
Lock Out - System nur zum Festsetzen des Schiebers fr die Bearbeitung. Vor der Produktion entfernen!Use Lock Out - System only to lock the cam for processing. Remove before production!
Das Schlauchsystem ist gem der Einbauverhltnisse demWerkzeug anzupassen. Die Platzierung der Anschluarmaturenund der Verschlauchung erfolgt kundenseitig.
The Gas Spring Linking has to be adapted to the tool integration.The position of the Control Panel and the Hose Linking is on thepart of the customer.
Das gesamte Schlauchsystem ist ber die Fa. DADCO zubestellen.
The complete Gas Spring Linking has to be ordered from DADCO.
Wird diese Schiebertype an die Kontrollarmatur angeschlossen,ist in der Bestellung kein Hinweis auf die Anschlussmglichkeitntig.
If this type of cam is linked with the Control Panel, an advice to theconnectivity is not neccessary in the order.
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S06
-
Entfernen der seitlichen FhrungsklammernSchieber nach oben herausnehmenSchraube entfernenHalteplatteGasdruckfeder nach hinten herausziehen
Ausbau der Gasdruckfeder unter der Presse:01.02.03.04.05.
um 90 drehen und herausziehen
Removing the Gas Spring Ejector below the Press:01.02.03.04.
Remove Side PlatesPull out Cam Slider upwardsRemove screwTurn around the Stop Plate for 90 and remove
05. Pull the Gas Spring Ejector backwards
Schieberbreite / Cam Unit Width + min. 140 mm
Der Ausbau darf nur im entspanntenZustand der Gasdruckfeder erfolgen!
Removing is only allowed for the extendedmoment of the Gas Spring Ejector!
Freiraum zum Wechsel der Gasdruckfeder / Free space for exchanging the Gas Spring Ejector
Schraube entfernenHalteplatte um 90 drehen und herausziehenSchieber mit allen Anbauteilen nach hintenherausziehen und entfernenGasdruckfeder nach hinten herausziehen
Alternativer Gasdruckfeder-Ausbau unter der Presse:01.02.03.
04.
Alternative removing the Gas Spring Ejector below the Press:01.02.03.04.
Remove screw
Pull back Cam Slider with all attachment parts and removePull the Gas Spring Ejector backwards
Turn around the Stop Plate for 90 and remove
195mm
195mm
Bei den seitlichen Fhrungsklammern ist auf Zugnglichkeit derBefestigungsschrauben und Stifte zur Klammereinstellung bzw. Demontagedes Schiebers zu achten. Empfehlung: Seitlicher Freiraum mindestens 70mm.Wenn dies aus Platzgrnden nicht mglich ist, muss der Schieberteil fr eineKlammernachstellung demontiert werden.
At the side plates take care of free access to the fixing screws and pins forplate adjustment resp. disassembly of the cam. Advice: free side areaminimum 70mm. If impossible in case of space reasons, the cam part has tobe disassembled for readjusting the plate.
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S07
-
16 25 16
19 32 19
23 44 23
28 58 28
20 20
3x
20
70
10
10
50
Die Schieberkaft wird gem Skizze weitergeleitet.The camforce is passed on according the diagram.
Abschulterung /
Presse / :Schieberfhrung / :
Treiber / :
Shouldering:
PressCam Base
Cam Driver
hh
HV
1
2
2
2
VH
1
1
(oben / )(unten / )
ertikalhorizontal(v )( )
(horizontal)(vertikal)
abovebelow
Erluterung / ):(Beispiel /Explanation Example
Ident NrCode No
Kraft im Mittelpunkt des FeldesForce in the centre of area
Wert der Kraft KNValue of Force KN
Hhe der berechneten ArbeitsflcheHeight calculated Working Area
Arbeitsflche obenWorking Area above
Breite der ArbeitsflcheWidth Working Area
grte Kraftmaximum force
BeschreibungDescription
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche / )
Acceptable Cam ForceView Working Area
Kraftverteilung / Force Distribution
Shouldering RetractilityAbschulterung Abstreifkraft
(KN)(mm)
100 %
80 %
60 %
40 %
20 %
0 %(0 KN)
Die Einfrbung der Krftediagramme erfolgtje Neigung im Wertebereich von 0% (0 KN)bis 100% (max. Schieberkraft).
The colouring of the diagrams is raised byevery bent in range of 0% (0 KN) to 100%(max. Cam Force).
Kraftverteilungfr max. Schieberkraft
(KN)
(KN)
SchieberWinkelCamAngle
max.Schieber
Kraftmax.Cam
Force
Force Distributionfor max. Cam Force
HS-UT 050-022511
V2
AbschulterungShouldering
V1
h1H1
SchieberkraftCam Force
AbstreifkraftRetractility
h2
V1 H1 V2 H2 h1 h2
00 o 58 49 59 49 0 90 25 0,9
05 o 81 76 76 69 5 90 25 1,0
10 o 83 84 70 70 11 90 25 0,9
15 o 83 84 70 70 11 90 25 0,9
20 o 83 84 59 56 19 80 25 0,9
Fr einen ruhigen Schieberlauf und lange Standzeiten der Gleitplattenwird empfohlen, den Kraftschwerpunkt mglichst in den Bereich desKraftzentrums zu legen.
For a smooth flow and a long life of the Wear Plates it is recommendedto lay the centre of gravity in the area of the centre of force.
The following diagrams illustrate, for each separate field, the possiblereceiving size of the camforce working not only in the centre of the fieldbut at the same time in the exact direction of course of the cam. Ifseveral forces work simultaneously the common centre of force has tobe specified and compared with the information of the tabular.
Die folgenden Tafeln zeigen fr jedes Feld die aufnehmbare Greeiner im Mittelpunkt dieses Feldes und genau in Laufrichtung desSchiebers wirkenden Schieberkraft. Bei mehreren auftretenden Krftenist deren gemeinsamer Kraftschwerpunkt zu ermitteln und mit denAngaben in der Tabelle zu vergleichen.
Alle eingeleiteten Krfte mssen immer niedriger ausfallen als dieTabellenangaben.
All incoming forces always have to be lower than the tabular values.
Die berbauung der Arbeitsflche ist ohne Rcksprache mitnicht zulssig.voestalpine
Reibungsverluste und andere die Laufkraft beeinflussendeGegebenheiten (Winkelstellung) sind in der Ermittlung derRckzugskrfte enthalten und bercksichtigt worden.
To overbuild the work space is not acceptable before consulting.alpinevoest
The friction loss and other data affecting the flow force (angle position)are contained in the determination of the retraction forces and havebeen considered.
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S08
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 050-022511
HS-UT 050-522512
HS-UT 050-1022513
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
16 25 16 16 25 16
19 32 19 19 32 19
23 44 23 23 44 23
28 58 28 28 58 28
20 33 20 20 33 20
24 43 24 24 43 24
30 60 30 30 60 30
35 81 35 35 81 35
21 35 21 21 35 21
26 45 26 26 45 26
32 63 32 32 63 32
37 83 37 37 83 37
50 50
10
10
3x
20
70
20 20 20 2010
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S09
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 050-1522514
HS-UT 050-2022515
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
20 33 20 20 33 20
25 45 25 25 45 25
32 68 32 32 68 32
39 83 39 39 83 39
20 33 20 20 33 20
25 45 25 25 45 25
33 70 33 33 70 33
40 83 40 40 71 40
50 50
3x
20
70
10
10 1020 20 20 20
HSUT 0050 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S10
-
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S00
-
Technische Daten / :Specification
* Bestellbeispiel / : 22523 / HS-UT 060-10 / 60 HubOrder Example
Arbeitsflche / (BxH):Einbau / :Schieber / :Presskraft / (min.):
hhebreite
(Details siehe Diagramm / )
Working AreaClosed Height
Cam Unit WidthPress Force
For details see diagramm
Horizontalschieber /Baugre / : HS-UT 060-0 bis / 20
Horizontal CamType to
60 mm x 70 mm210 mm (170 mm - 0)60 mm6 to
Ident-Nr.
Code No.
Bezeichnung:
Description:
Hub
Stroke
22520 HS-UT 060-0 45
22521 HS-UT 060-0 60
22522 HS-UT 060-5 60
22523 HS-UT 060-10 60
22524 HS-UT 060-15 60
22525 HS-UT 060-20 60
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S01
-
3D Ansicht3D View
AblaufdiagrammCam Diagram
Draufsicht TreiberPlan View Cam Driver
Ansicht XView X
Schnitt A-ASection A-A
Draufsicht Schieberfhrung / Plan View Cam Base
Achtung !Bei 0 ohne Adapterplatte
Attention !
At 0 without Adapter Plate
Rd. 8H7 (2x)
Rd. 8H7 (2x)
Draufsicht Adapterplatte /(5-20)
Plan View Adapter Plate
Auf Zugnglichkeit derSchrauben und Stifte achten!
Verschraubung M8 (4x)
Take care for free accessto screws and dowels!
Screw Connection
Verschraubung
Auf Zugnglichkeit derSchrauben und Stifte achten!
M8 (4x)Screw Connection
Take care for free access toscrews and dowels!
Konstruktions-EinfgepunktTooling-Ball
ArbeitsflcheWorking Area
Gasdruckfederweg = HubGasspringway = Stroke
A A
Bau
hhe
/C
lose
d H
eigh
t
X
Hub +2Stroke +2
FestsetzmaFix Measure
Rd. 8H7 (2x)
Auf Zugnglichkeit derSchrauben und Stifte achten!
Verschraubung M8 (4x)
Take care for free accessto screws and dowels!
Screw Connection
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S02
-
Mae / Measures
FestsetzmaFix Measure
Bauhhe / 0,2Closed Height
Retractility
Ident-Nr.Code No.
HubStroke
Cam Angle
GasdruckfederwegGas Spring Way
Abstreifkraft
HubStroke
Schieberwinkel
Alle nicht tolerierten Mae entsprechen ISO 2768 Mittel. Dimensions without tolerance are analog to ISO 2768 middle.
Stiftlcher werden mit 0,02mm Toleranz gefertigt. Dowel holes will be manufactured with 0,02mm tolerance.
Fr geringere Rckzugskrfte (z.B.: beim Einsatz einesseparaten Abstreifers auf dem Schieber) ist esempfehlenswert, den Druck der Gasdruckfeder zurSchonung der Presse oder Minimierung der elastischenVerformung im Werkzeugguss zu reduzieren (min.18 bar).
For lower retraction forces (for example when a separatestripper is mounted on the cam) it is recommandable toreduce the gas spring pressure (min. 18 bar) in order to sparethe press or minimize the elastic deformation in the tool cast.
F0 / F1 (KN): 0,9 / 1,1
Presskraft Gasdruckfeder:Gas Spring Force
F0: Anfangskraft
F1: Endkraftstarting force
ending force
GewichtWeight
0 0 5 10 15 20
170 170 210 210 210 210
+ 0,06+ 0,04+ 0,06+ 0,04
1715 15 18 18
35
49 64 64 64 64 64
50 50 45 40
29,7 41,1
40
51,8
X 53,63 71,51 65,0 60,0 64,16 60,0
~ T 10,0 10,0 22,7
30 3030 30 30
~ S 135,0 135,0 168,0 155,8 148,4 135,9
R 30
15 15 10
Q 110 135 135 140 115 115
P 15 20 20
40 40 40
O 10 15 15 10 10 5
N - - 40
160 170 175
M1 100 130 130 130 130 130
M - - 155
45 35 25
L 1 50 50 50 50 50 50
L - - 50
25 15 5
K1 60 60 60 60 60 60
K - - 35
22
22 22 22 22 22 22
- - 22 22
58 67
22
82
I1 0,02 50 81 81 81 81 81
I 0,02 - - 49
100 85120 110 80
H 35 35 35 35 35 35
G 110
55 45 35
F 121 151 165 170 180 185
E 70 70 60
80 80 80
D 0,02 100 100 140 135 135 130
C2 0,02 80 80 80
5 5 5
C1 0,02 60 60 60 60 60 60
C 0,02 10 5 5
0 0-
B1 - - 5
B0
5 5
15 20
A 0,02 125 150 150 155 130 130
0 0 5 10
60 60
0,9 1,0
45 60 60 60
45 60 60
22524
1,0 1,0
22525
60 60 60
1,0 1,0
17
22520 22521 22522 22523
J
J1
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S03
-
Fhrungsklammer (L)Side Plate (L)
Fhrungsklammer (R)Side Plate (R)
SchieberCam Slider
SchieberfhrungCam Base
GasdruckfederGas Spring
Zwangsrckholer (L)Positive Return (L)
Bauteile / Components
AufnahmeplatteMounting Plate
TreiberCam Driver
Adapterplatte
(5 - 20)Adapter Plate
GleitplatteWear Plate
HalteplatteStop Plate
Passfeder (B)Fitting Key (B)
AnschlagbolzenStop Bolt
DmpferDamping Element
Passfeder (A)Fitting Key (A)
Lock Out StiftLock Out Pin
Zwangsrckholer (R)Positive Return (R)
Passfeder (C)
(5 - 20)Fitting Key (C)
Passfeder (A)
(5 - 20)Fitting Key (A)
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S04
-
Stckliste / Component Parts
Damping Element
Positive Return (R)
Positive Return (L)
Gas Spring Ejector
Side Plate (L)
Side Plate (R)
Cam Base
Cam Slider
Cam Driver
Description Material
Code No.
Stop Plate
Wear Plate
Adapter Plate
Fitting Key (A)
Mounting Plate
Stop Bolt
Fitting Key (B)
Es ist darauf zu achten, dass der Schraubverschluss derGasdruckfeder unbedingt vor Inbetriebnahmeeingeschraubt und zustzlich eingeklebt werden muss!
It is important to ensure that the Screw Lock of the GasSpring is screwed in and secured with Loctite (or similar)before use!
Die Gewhrleistung erstreckt sich nur auf die kompletteSchiebereinheit.
The warranty is only extended to the complete cam unit.
Lieferumfang:Schiebereinheit, Pafedern, Lock Out - System
Scope of delivery:Cam unit, Fitting Keys, Lock Out - System
Ident-Nr.
Bezeichnung Material
Treiber
Schieber
Schieberfhrung
Anschlagbolzen
Gasdruckfeder
Aufnahmeplatte
Fhrungsklammer (L)
Fhrungsklammer (R)
Halteplatte
Dmpfer
Gleitplatte
Zwangsrckholer (L)
Zwangsrckholer (R)
Adapterplatte
Passfeder (A)
Passfeder (B)
Passfeder (C)104225 104225 1042251.0503.07 - - 104225
22520
0 0 5 10 15 20
22521 22522 22523 22524 22525
1.7225 104253 104298 104259 104262 104264 104267
0.7070 105814 105816 105817 105818 105819 105820
WF 750/1A 21302 21303 21303 21303 21303 21303
1.7225 103985 103985 103985 103985 103985 103985
DADCO 101543 101544 101544 101544 101544 101544
1.7225 105815 105815 105815 105815 105815 105815
1.7225 103987 103987 103987 103987 103987 103987
1.7225 103989 103989 103989 103989 103989 103989
1.7225 103993 103993 103993 103993 103993 103993
PUR 101498 101498 101498 101498 101498 101498
WF 750/1A 18226 18241 18241 18241 18226 18226
1.7225 104047 104047 104047 104047 104047 104047
1.7225 104046 104046 104046 104046 104046 104046
1.7225 - - 104258 104261 104263 104266
1.0503.07 104256 104256 104256 104256 104256 104256
1.0503.07 - - 104255 104255 104255 104255
Fitting Key (C)
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S05
-
SchieberCam Slider
TreiberCam Driver
Gasdruckfeder SchlauchsystemGas Spring Linking Gasdruckfeder
Gas Spring
Anschluss Adapter (2x)Port Adapter
SchlauchHose
Kontrollarmatur (1x)Mini Control Panel (1x)
Schlauch Adapter (2x)Hose Adapter (2x)
SchieberfhrungCam Base
Lock Out Stift(nicht im Lieferumfang)Lock Out Pin(not in scope of delivery)
AufnahmeplatteMounting Plate
Lock Out Stift um Festsetzen des Schiebers verwenden!z
(nicht im Lieferumfang / )Use Lock Out Pin to lock the Cam!
not in scope of delivery
Lock Out - System
Lock Out - System nur zum Festsetzen des Schiebers fr die Bearbeitung. Vor der Produktion entfernen!Use Lock Out - System only to lock the cam for processing. Remove before production!
Das Schlauchsystem ist gem der Einbauverhltnisse demWerkzeug anzupassen. Die Platzierung der Anschluarmaturenund der Verschlauchung erfolgt kundenseitig.
The Gas Spring Linking has to be adapted to the tool integration.The position of the Control Panel and the Hose Linking is on thepart of the customer.
Das gesamte Schlauchsystem ist ber die Fa. DADCO zubestellen.
The complete Gas Spring Linking has to be ordered from DADCO.
Wird diese Schiebertype an die Kontrollarmatur angeschlossen,ist in der Bestellung kein Hinweis auf die Anschlussmglichkeitntig.
If this type of cam is linked with the Control Panel, an advice to theconnectivity is not neccessary in the order.
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S06
-
Schieberbreite / Cam Unit Width + min. 140 mm
Der Ausbau darf nur im entspanntenZustand der Gasdruckfeder erfolgen!
Removing is only allowed for the extendedmoment of the Gas Spring Ejector!
Freiraum zum Wechsel der Gasdruckfeder / Free space for exchanging the Gas Spring Ejector
195mm
195mm
Bei den seitlichen Fhrungsklammern ist auf Zugnglichkeit derBefestigungsschrauben und Stifte zur Klammereinstellung bzw. Demontagedes Schiebers zu achten. Empfehlung: Seitlicher Freiraum mindestens 70mm.Wenn dies aus Platzgrnden nicht mglich ist, muss der Schieberteil fr eineKlammernachstellung demontiert werden.
At the side plates take care of free access to the fixing screws and pins forplate adjustment resp. disassembly of the cam. Advice: free side areaminimum 70mm. If impossible in case of space reasons, the cam part has tobe disassembled for readjusting the Plate.
Removing the Gas Spring Ejector below the Press:01.02.03.04.
Remove Side PlatesPull out Cam Slider upwardsRemove screwTurn around the Stop Plate for 90 and remove
05. Pull the Gas Spring Ejector backwards
Alternative removing the Gas Spring Ejector below the Press:01.02.03.04.
Remove screw
Pull back Cam Slider with all attachment parts and removePull the Gas Spring Ejector backwards
Turn around the Stop Plate for 90 and remove
Entfernen der seitlichen FhrungsklammernSchieber nach oben herausnehmenSchraube entfernenHalteplatteGasdruckfeder nach hinten herausziehen
Ausbau der Gasdruckfeder unter der Presse:01.02.03.04.05.
um 90 drehen und herausziehen
Schraube entfernenHalteplatte um 90 drehen und herausziehenSchieber mit allen Anbauteilen nach hintenherausziehen und entfernenGasdruckfeder nach hinten herausziehen
Alternativer Gasdruckfeder-Ausbau unter der Presse:01.02.03.
04.
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S07
-
14 28 14
17 39 17
21 59 21
24 88 24
60
10
3 x 20
3x
20
70
Die Schieberkaft wird gem Skizze weitergeleitet.The camforce is passed on according the diagram.
Abschulterung /
Presse / :Schieberfhrung / :
Treiber / :
Shouldering:
PressCam Base
Cam Driver
hh
HV
1
2
2
2
VH
1
1
(oben / )(unten / )
ertikalhorizontal(v )( )
(horizontal)(vertikal)
abovebelow
Erluterung / ):(Beispiel /Explanation Example
Ident NrCode No
Kraft im Mittelpunkt des FeldesForce in the centre of area
Wert der Kraft KNValue of Force KN
Hhe der berechneten ArbeitsflcheHeight calculated Working Area
Arbeitsflche obenWorking Area above
Breite der ArbeitsflcheWidth Working Area
grte Kraftmaximum force
BeschreibungDescription
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche / )
Acceptable Cam ForceView Working Area
Kraftverteilung / Force Distribution
Shouldering RetractilityAbschulterung Abstreifkraft
(KN)(mm)
100 %
80 %
60 %
40 %
20 %
0 %(0 KN)
Die Einfrbung der Krftediagramme erfolgtje Neigung im Wertebereich von 0% (0 KN)bis 100% (max. Schieberkraft).
The colouring of the diagrams is raised byevery bent in range of 0% (0 KN) to 100%(max. Cam Force).
Kraftverteilungfr max. Schieberkraft
(KN)
(KN)
SchieberWinkelCamAngle
max.Schieber
Kraftmax.Cam
Force
Force Distributionfor max. Cam Force
HS-UT 060-022521
V1 H1 V2 H2 h1 h2
00 o 88 75 89 75 0 100 25 0,9
05 o 111 103 103 94 7 90 25 1,0
10 o 110 111 93 92 15 90 25 1,0
15 o 140 141 118 117 19 80 25 1,0
20 o 106 107 75 71 25 80 25 1,0
V2
AbschulterungShouldering
V1
h1H1
SchieberkraftCam Force
AbstreifkraftRetractility
h2
Fr einen ruhigen Schieberlauf und lange Standzeiten der Gleitplattenwird empfohlen, den Kraftschwerpunkt mglichst in den Bereich desKraftzentrums zu legen.
For a smooth flow and a long life of the Wear Plates it is recommendedto lay the centre of gravity in the area of the centre of force.
The following diagrams illustrate, for each separate field, the possiblereceiving size of the camforce working not only in the centre of the fieldbut at the same time in the exact direction of course of the cam. Ifseveral forces work simultaneously the common centre of force has tobe specified and compared with the information of the tabular.
Die folgenden Tafeln zeigen fr jedes Feld die aufnehmbare Greeiner im Mittelpunkt dieses Feldes und genau in Laufrichtung desSchiebers wirkenden Schieberkraft. Bei mehreren auftretenden Krftenist deren gemeinsamer Kraftschwerpunkt zu ermitteln und mit denAngaben in der Tabelle zu vergleichen.
Alle eingeleiteten Krfte mssen immer niedriger ausfallen als dieTabellenangaben.
All incoming forces always have to be lower than the tabular values.
Die berbauung der Arbeitsflche ist ohne Rcksprache mitnicht zulssig.voestalpine
Reibungsverluste und andere die Laufkraft beeinflussendeGegebenheiten (Winkelstellung) sind in der Ermittlung derRckzugskrfte enthalten und bercksichtigt worden.
To overbuild the work space is not acceptable before consulting.alpinevoest
The friction loss and other data affecting the flow force (angle position)are contained in the determination of the retraction forces and havebeen considered.
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S08
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 060-02252022521
HS-UT 060-522522
HS-UT 060-1022523
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
14 28 14 14 28 14
17 39 17 17 39 17
21 59 21 21 59 21
24 88 24 24 54 24
23 43 23 23 43 23
28 56 28 28 56 28
34 80 34 34 80 34
39 111 39 39 111 39
24 43 24 24 43 24
29 57 29 29 57 29
35 80 35 35 80 35
40 110 40 40 110 40
603 x 20
60
10
3 x 20
3x
20
70
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S09
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 060-1522524
HS-UT 060-2022525
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
23 42 23 23 42 23
28 60 28 28 60 28
37 95 37 37 95 37
43 140 43 43 122 43
23 42 23 23 42 23
28 59 28 28 59 28
36 93 36 36 92 36
43 106 43 43 92 43
3x
20
70
10
3 x 20 3 x 2060 60
HSUT 0060 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S10
-
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S00
-
Technische Daten / :Specification
* Bestellbeispiel / : 22533 / HS-UT 085-10 / 45 HubOrder Example
Ident-Nr.
Code No.
Bezeichnung:
Description:
Arbeitsflche / (BxH):Einbau / :Schieber / :Presskraft / (min.):
hhebreite
(Details siehe Diagramm / )
Working AreaClosed Height
Cam Unit WidthPress Force
For details see diagramm
Horizontalschieber /Baugre / : HS-UT 085-0 bis / 20
Horizontal CamType to
85 mm x 90 mm
Hub
Stroke
22530 HS-UT 085-0 35
22531 HS-UT 085-0 45
22532 HS-UT 085-5 45
22533 HS-UT 085-10 45
22534 HS-UT 085-15 45
22535 HS-UT 085-20 45
22536 HS-UT 085-0 75
22537 HS-UT 085-5 75
22538 HS-UT 085-10 75
22539 HS-UT 085-15 75
22540 HS-UT 085-20 75
siehe Seite 3 /
85 mm13 to
see page 3
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S01
-
3D Ansicht3D View
AblaufdiagrammCam Diagram
Draufsicht TreiberPlan View Cam Driver
Ansicht XView X
Schnitt A-ASection A-A
Draufsicht Schieberfhrung / Plan View Cam Base
Gasdruckfederweg = HubGasspringway = Stroke
Bau
hhe
/C
lose
d H
eigh
t
X
Hub +2Stroke +2
FestsetzmaFix Measure
Konstruktions-EinfgepunktTooling-Ball
ArbeitsflcheWorking Area
Verschraubung
Auf Zugnglichkeitder Schrauben undStifte achten!
M12 (4x)Screw Connection
Take care for freeaccess to screwsand dowels!
Achtung !0 / 35mm und / 0-20 / 75mmohne Adapterplatte
Attention !and
without Adapter Plate
Verschraubung
Auf Zugnglichkeit derSchrauben und Stifte achten!
M12 (4x)Screw Connection
Take care for free access toscrews and dowels!
Rd. 12H7 (2x)
Rd. 12H7 (2x)Draufsicht Adapterplatte(0-20 / 45mm)Plan View Adapter Plate
A A
Rd. 10H7 (2x)Verschraubung M10 (4x)Screw Connection
Auf Zugnglichkeit derSchrauben und Stifte achten!Take care for free access toscrews and dowels!
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S02
-
Mae / Measures
FestsetzmaFix Measure
Bauhhe / 0,2Closed Height
Retractility
Ident-Nr.Code No.
Cam Angle
GasdruckfederwegGas Spring Way
Abstreifkraft
HubStroke
Schieberwinkel
Alle nicht tolerierten Mae entsprechen ISO 2768 Mittel. Dimensions without tolerance are analog to ISO 2768 middle.
Stiftlcher werden mit 0,02mm Toleranz gefertigt. Dowel holes will be manufactured with 0,02mm tolerance.
Fr geringere Rckzugskrfte (z.B.: beim Einsatz einesseparaten Abstreifers auf dem Schieber) ist esempfehlenswert, den Druck der Gasdruckfeder zurSchonung der Presse oder Minimierung der elastischenVerformung im Werkzeugguss zu reduzieren (min.18 bar).
For lower retraction forces (for example when a separatestripper is mounted on the cam) it is recommandable toreduce the gas spring pressure (min. 18 bar) in order to sparethe press or minimize the elastic deformation in the tool cast.
F0 / F1 (KN): 2,0 / 2,7Presskraft Gasdruckfeder / :Gas Spring Force F0: Anfangskraft /F1: Endkraft /
starting forceending force
GewichtWeight
0 0 5 10 15 20 0 5 10 15 20
195 225 225 225 240 245 225 225 225 225 225
+ 0,06+ 0,04+ 0,06+ 0,04
79 79
40 35
39 49 49 49
40
49 49 79 79 79
40 35 50 4550 50 45 40
81,25 75,0 80,20 75,045,0 48,12 45,0 89,38X 41,71 53,63 48,75
25,6 38,3 51,0 63,835,9 54,9 68,9 10,0~ T 10,0 10,0 21,9
181,0 171,7 167,2 162,5186,5 181,7 176,6 190,0~ S 175,0 205,0 195,9
60 60 60 6060 60 60 60R 60 60 60
250 250 260 265235 240 240 255Q 207 230 230
145 140 155 155130 135 120 145P 117 135 130
140 135 150 150125 130 115 140O 112 130 125
- - - -40 40 40 -N - 40 40
63 63 63 6363 63 63 63M1 63 63 63
- - - -60 60 60 -M - 60 60
290 285 290 300227 227 227 277L1 186 227 227
- - - -230 240 290 -L - 215 225
70 85 85 9542 42 42 47K2 48 42 42
55 80 80 9037 37 37 37K1 33 37 37
- - - -80 95 105 -K - 55 70
25 25 25 25
- - -
25 25 25 25 25 25 25
25 25 - -- 25 25 25
180 190 200 210140 140 140 170I1 0,02 115 140 140
- - - -190 200 210 -I 0,02 - 170 180
30 30 30 3045 45 45 30H 75 45 45
110 100 95 8297 102 95 135G 115 115 105
315 320 325 335270 275 305 302F 212 247 260
35 45 55 6540 55 65 22E 22 22 30
150 140 135 130140 135 130 160D 0,02 100 160 150
0 0 0 015 15 15 0C3 0,02 45 15 15
12 12 12 1212 12 12 12C2 0,02 12 12 12
35 35 35 3535 35 35 35C1 0,02 35 35 35
96 96 96 9695 95 95 96C 0,02 62 95 95
125 120 140 140115 120 105 125B 102 115 115
265 265 275 280250 255 255 270A 0,02 222 245 245
5 10 15 20
75 75 75
0 0 5 10 15 20 0
45 45 75 7535 45 45 45
2,2 2,2 2,2 2,2
75 75 75
2,3 2,3 2,2 2,2 2,2 2,2 2,3
45 45 75 75
22532 22533
35 45 45 45
22538 22539 2254022534 22535 22536 2253722530 22531
21 24 27 27 31 30 3331 30 31 30
J
J1
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S03
-
Fhrungsklammer (L)Side Plate (L)
Fhrungsklammer (R)Side Plate (R)
SchieberCam Slider
SchieberfhrungCam Base
GasdruckfederGas Spring
Zwangsrckholer (L)Positive Return (L)
Bauteile / Components
AufnahmeplatteMounting Plate
TreiberCam Driver
Adapterplatte
(0 - 20 / 45)Adapter Plate
GleitplatteWear Plate
HalteplatteStop Plate
Passfeder (B)
(0 - 20 / 45)(0 - 20 / 75)
Fitting Key (B)
AnschlagbolzenStop Bolt
DmpferDamping Element
Passfeder (A)
(0 - 20 / 45)(0 / 35)
Fitting Key (A)
Zwangsrckholer (R)Positive Return (R)
Lock Out StiftLock Out Pin
Passfeder (A)
(0 - 20 / 45)(0 - 20 / 75)
Fitting Key (A)
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S04
-
Stckliste / Component Parts
Damping Element
Positive Return (R)
Positive Return (L)
Gas Spring Ejector
Side Plate (L)
Side Plate (R)
Cam Base
Cam Slider
Cam Driver
Description Material
Code No.
Stop Plate
Wear Plate
Adapter Plate
Fitting Key (A)
Mounting Plate
Stop Bolt
Fitting Key (B)
Es ist darauf zu achten, dass der Schraubverschluss derGasdruckfeder unbedingt vor Inbetriebnahmeeingeschraubt und zustzlich eingeklebt werden muss!
It is important to ensure that the Screw Lock of the GasSpring is screwed in and secured with Loctite (or similar)before use!
Die Gewhrleistung erstreckt sich nur auf die kompletteSchiebereinheit.
The warranty is only extended to the complete cam unit.
Lieferumfang:Schiebereinheit, Pafedern, Lock Out - System
Scope of delivery:Cam unit, Fitting Keys, Lock Out - System
Ident-Nr.
Bezeichnung Material
Treiber
Schieber
Schieberfhrung
Anschlagbolzen
Gasdruckfeder
Aufnahmeplatte
Fhrungsklammer (L)
Fhrungsklammer (R)
Halteplatte
Dmpfer
Gleitplatte
Zwangsrckholer (L)
Zwangsrckholer (R)
Adapterplatte
Passfeder (A)
Passfeder (B)
22530 22531 22532 22533 22534 22535 22536 22537 22538 22539 22540
0 0 5 10 15 20 0 5 10 15 20
1.7225 104274 104276 104278 104281 104284 104287 104290 104292 104293 104294 104296
0.7070 105824 105838 105821 105839 105840 105841 105847 105846 105845 105844 105843
WF 750/1A 21341 22084 22084 22084 22084 22084 21345 22085 22086 22087 22088
1.7225 104170 104170 104170 104170 104170 104170 104170 104170 104170 104170 104170
DADCO 101568 101552 101552 101552 101552 101552 101554 101554 101554 101554 101554
1.7225 105822 105822 105822 105822 105822 105822 105822 105822 105822 105822 105822
1.7225 104172 104175 104175 104175 104175 104175 104177 104177 104177 104177 104177
1.7225 104173 104176 104176 104176 104176 104176 104178 104178 104178 104178 104178
1.7225 104174 104174 104174 104174 104174 104174 104174 104174 104174 104174 104174
PUR 101498 101498 101498 101498 101498 101498 101498 101498 101498 101498 101498
WF 750/1A 18231 18231 18231 18231 18231 18231 18232 18231 18231 18231 18231
1.7225 102874 102874 102874 102874 102874 102874 102874 102874 102874 102874 102874
1.7225 105361 105361 105361 105361 105361 105361 105361 105361 105361 105361 105361
1.7225 - 104301 104277 104280 104283 104286 - - - - -
- -1.0503.07 23388 23388 23388 -
23390 23390 23390 23390 23390
23388 23388 23388
233901.0503.07 - 23390 23390 23390 23390
--
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S05
-
Lock Out Stift um Festsetzen des Schiebers verwenden!z
(nicht im Lieferumfang / )Use Lock Out Pin to lock the Cam!
not in scope of delivery
Lock Out Stift(nicht im Lieferumfang)Lock Out Pin(not in scope of delivery)
SchieberCam Slider
TreiberCam Driver
Gasdruckfeder SchlauchsystemGas Spring Linking
GasdruckfederGas Spring
Anschluss Adapter (2x)Port Adapter
SchlauchHose
Kontrollarmatur (1x)Mini Control Panel (1x)
Schlauch Adapter (2x)Hose Adapter (2x)
Lock Out - System
SchieberfhrungCam Base
AufnahmeplatteMounting Plate
Lock Out - System nur zum Festsetzen des Schiebers fr die Bearbeitung. Vor der Produktion entfernen!Use Lock Out - System only to lock the cam for processing. Remove before production!
Das Schlauchsystem ist gem der Einbauverhltnisse demWerkzeug anzupassen. Die Platzierung der Anschluarmaturenund der Verschlauchung erfolgt kundenseitig.
The Gas Spring Linking has to be adapted to the tool integration.The position of the Control Panel and the Hose Linking is on thepart of the customer.
Das gesamte Schlauchsystem ist ber die Fa. DADCO zubestellen.
The complete Gas Spring Linking has to be ordered from DADCO.
Wird diese Schiebertype an die Kontrollarmatur angeschlossen,ist in der Bestellung kein Hinweis auf die Anschlussmglichkeitntig.
If this type of cam is linked with the Control Panel, an advice to theconnectivity is not neccessary in the order.
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S06
-
Schieberbreite / Cam Unit Width + min. 140 mm
Der Ausbau darf nur im entspanntenZustand der Gasdruckfeder erfolgen!
Removing is only allowed for the extendedmoment of the Gas Spring Ejector!
Freiraum zum Wechsel der Gasdruckfeder / Free space for exchanging the Gas Spring Ejector
225mm
225 mm
Removing the Gas Spring Ejector below the Press:01.02.03.04.
Remove Side PlatesPull out Cam Slider upwardsRemove screwTurn around the Stop Plate for 90 and remove
05. Pull the Gas Spring Ejector backwards
Alternative removing the Gas Spring Ejector below the Press:01.02.03.04.
Remove screw
Pull back Cam Slider with all attachment parts and removePull the Gas Spring Ejector backwards
Turn around the Stop Plate for 90 and remove
Entfernen der seitlichen FhrungsklammernSchieber nach oben herausnehmenSchraube entfernenHalteplatteGasdruckfeder nach hinten herausziehen
Ausbau der Gasdruckfeder unter der Presse:01.02.03.04.05.
um 90 drehen und herausziehen
Schraube entfernenHalteplatte um 90 drehen und herausziehenSchieber mit allen Anbauteilen nach hintenherausziehen und entfernenGasdruckfeder nach hinten herausziehen
Alternativer Gasdruckfeder-Ausbau unter der Presse:01.02.03.
04.
Bei den seitlichen Fhrungsklammern ist auf Zugnglichkeit derBefestigungsschrauben und Stifte zur Klammereinstellung bzw. Demontagedes Schiebers zu achten. Empfehlung: Seitlicher Freiraum mindestens 70mm.Wenn dies aus Platzgrnden nicht mglich ist, muss der Schieberteil fr eineKlammernachstellung demontiert werden.
At the side plates take care of free access to the fixing screws and pins forplate adjustment resp. disassembly of the cam. Advice: free side areaminimum 70mm. If impossible in case of space reasons, the cam part has tobe disassembled for readjusting the Plate.
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S07
-
27 36 49 36 27
31 42 61 42 31
36 51 78 51 36
43 64 109 64 43
49 76 137 76 49
90
853 x 1520 20
4x
2010
Die Schieberkaft wird gem Skizze weitergeleitet.The camforce is passed on according the diagram.
Abschulterung /
Presse / :Schieberfhrung / :
Treiber / :
Shouldering:
PressCam Base
Cam Driver
hh
HV
1
2
2
2
VH
1
1
(oben / )(unten / )
ertikalhorizontal(v )( )
(horizontal)(vertikal)
abovebelow
Erluterung / ):(Beispiel /Explanation Example
Ident NrCode No
Kraft im Mittelpunkt des FeldesForce in the centre of area
Wert der Kraft KNValue of Force KN
Hhe der berechnetenArbeitsflcheHeight calculatedWorking Area
Arbeitsflche obenWorking Area above
Breite der ArbeitsflcheWidth Working Area
grte Kraftmaximum force
BeschreibungDescription
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche / )
Acceptable Cam ForceView Working Area
Kraftverteilung / Force Distribution
Shouldering RetractilityAbschulterung Abstreifkraft
(KN)(mm)
100 %
80 %
60 %
40 %
20 %
0 %(0 KN)
Die Einfrbung der Krftediagramme erfolgtje Neigung im Wertebereich von 0% (0 KN)bis 100% (max. Schieberkraft).
The colouring of the diagrams is raised byevery bent in range of 0% (0 KN) to 100%(max. Cam Force).
Kraftverteilungfr max. Schieberkraft
(KN)
(KN)
SchieberWinkelCamAngle
max.Schieber
Kraftmax.Cam
Force
Force Distributionfor max. Cam Force
HS-UT 085-022530
V2
AbschulterungShouldering
V1
h1H1
SchieberkraftCam Force
AbstreifkraftRetractility
h2
V1 H1 V2 H2 h1 h2
00 o 137 117 139 117 0 100 25 2,3
05 o 136 128 128 116 8 90 25 2,2
10 o 135 137 115 114 18 90 25 2,2
15 o 137 139 117 116 18 90 25 2,2
20 o 137 139 98 93 31 80 25 2,2
Fr einen ruhigen Schieberlauf und lange Standzeiten der Gleitplattenwird empfohlen, den Kraftschwerpunkt mglichst in den Bereich desKraftzentrums zu legen.
For a smooth flow and a long life of the Wear Plates it is recommendedto lay the centre of gravity in the area of the centre of force.
The following diagrams illustrate, for each separate field, the possiblereceiving size of the camforce working not only in the centre of the fieldbut at the same time in the exact direction of course of the cam. Ifseveral forces work simultaneously the common centre of force has tobe specified and compared with the information of the tabular.
Die folgenden Tafeln zeigen fr jedes Feld die aufnehmbare Greeiner im Mittelpunkt dieses Feldes und genau in Laufrichtung desSchiebers wirkenden Schieberkraft. Bei mehreren auftretenden Krftenist deren gemeinsamer Kraftschwerpunkt zu ermitteln und mit denAngaben in der Tabelle zu vergleichen.
Alle eingeleiteten Krfte mssen immer niedriger ausfallen als dieTabellenangaben.
All incoming forces always have to be lower than the tabular values.
Die berbauung der Arbeitsflche ist ohne Rcksprache mitnicht zulssig.voestalpine
Reibungsverluste und andere die Laufkraft beeinflussendeGegebenheiten (Winkelstellung) sind in der Ermittlung derRckzugskrfte enthalten und bercksichtigt worden.
To overbuild the work space is not acceptable before consulting.alpinevoest
The friction loss and other data affecting the flow force (angle position)are contained in the determination of the retraction forces and havebeen considered.
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S08
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 085-0225302253122536
HS-UT 085-52253222537
HS-UT 085-102253322538
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
27 36 49 36 27 27 36 49 36 27
31 42 61 42 31 31 42 61 42 31
36 51 78 51 36 36 51 78 51 36
43 64 109 64 43 43 61 69 61 43
49 76 137 76 49 48 54 61 54 48
27 35 49 35 27 27 35 49 35 27
30 41 60 41 30 30 41 60 41 30
35 50 77 50 35 35 50 77 50 35
43 63 106 63 43 43 63 106 63 43
49 75 136 75 49 49 75 136 75 49
26 34 47 34 26 26 34 47 34 26
29 40 58 40 29 29 40 58 40 29
34 49 75 49 34 34 49 75 49 34
42 61 103 61 42 42 61 103 61 42
48 74 135 74 48 48 74 135 74 48
85
90
853 x 1520 2020
4x
20
20 3 x 15
10
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S09
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 085-152253422539
HS-UT 085-202253522540
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
27 36 50 36 27 27 36 50 36 27
31 43 62 43 31 31 43 62 43 31
37 52 81 52 37 37 52 81 52 37
45 68 119 68 45 45 68 119 68 45
53 84 137 84 53 52 84 137 84 52
27 36 50 36 27 27 36 50 36 27
31 43 62 43 31 31 43 62 43 31
37 52 81 52 37 37 52 81 52 37
45 68 119 68 45 45 68 119 68 45
53 84 137 84 53 53 84 137 84 53
85 85
4x
20
90
10
20 3 x 15 20 20 3 x 15 20
HSUT 0085 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S10
-
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S00
-
Technische Daten / :Specification
* Bestellbeispiel / : 22551 / HS-UT 110-05 / 75 HubOrder Example
Ident-Nr.
Code No.
Bezeichnung:
Description:
Arbeitsflche / (BxH):Einbau / :Schieber / :Presskraft / (min.):
hhebreite
(Details siehe Diagramm / )
Working AreaClosed Height
Cam Unit WidthPress Force
For details see diagramm
Horizontalschieber /Baugre / : HS-UT 110-0 bis / 20
Horizontal CamType to
110 mm x 110 mm275 mm110 mm19 to
22550 HS-UT 110-00 75
22551 HS-UT 110-05 75
22552 HS-UT 110-10 75
22553 HS-UT 110-15 75
22554 HS-UT 110-20 75
Hub
Stroke
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S01
-
3D Ansicht3D View
AblaufdiagrammCam Diagram
Draufsicht TreiberPlan View Cam Driver
Ansicht XView X
Schnitt A-ASection A-A
Draufsicht Schieberfhrung / Plan View Cam Base
Gasdruckfederweg = HubGasspringway = Stroke
Bau
hhe
/C
lose
d H
eigh
t
X
Hub +2Stroke +2
FestsetzmaFix Measure
Konstruktions-EinfgepunktTooling-Ball
ArbeitsflcheWorking Area
Verschraubung
Auf Zugnglichkeitder Schrauben undStifte achten!
M12 (4x)Screw Connection
Take care for freeaccess to screwsand dowels!
Rd. 12H7 (2x)
A A
Rd. 12H7 (2x)Verschraubung M12 (4x)Screw Connection
Auf Zugnglichkeit derSchrauben und Stifte achten!Take care for free access toscrews and dowels!
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S02
-
Mae / Measures
FestsetzmaFix Measure
Bauhhe / 0,2Closed Height
Retractility
Ident-Nr.Code No.
Cam Angle
GasdruckfederwegGas Spring Way
Abstreifkraft
HubStroke
Schieberwinkel
Alle nicht tolerierten Mae entsprechen ISO 2768 Mittel. Dimensions without tolerance are analog to ISO 2768 middle.
Stiftlcher werden mit 0,02mm Toleranz gefertigt. Dowel holes will be manufactured with 0,02mm tolerance.
Fr geringere Rckzugskrfte (z.B.: beim Einsatz einesseparaten Abstreifers auf dem Schieber) ist esempfehlenswert, den Druck der Gasdruckfeder zurSchonung der Presse oder Minimierung der elastischenVerformung im Werkzeugguss zu reduzieren (min.18 bar).
For lower retraction forces (for example when a separatestripper is mounted on the cam) it is recommandable toreduce the gas spring pressure (min. 18 bar) in order to sparethe press or minimize the elastic deformation in the tool cast.
F0 / F1 (KN): 3,1 / 4,2Presskraft Gasdruckfeder / :Gas Spring Force F0: Anfangskraft /F1: Endkraft /
starting forceending force
GewichtWeight
0 5 10 15 20
275 275 275 275 275
+ 0,06+ 0,04
22552 22553
2,5
22554
75 75
49
75 75 75
22550 22551
15
2,4
75 75 75 75 75
2,5 2,5 2,5
20
A 0,02 290 295 300 305 305
0 5 10
B 110 100 95
30 30
C 0,02 62 62 62
100 100
62 62
12 12
C1 0,02 30
C2 0,02 12 12 12
30 30
D 0,02 200 190 175
355 365
E 22 35 45
165 155
55 70
130 115
F 332
G 150 140 130
335 350
55
I 0,02 170 180 190 200 210
H 55 55
25 25 25
5555
90 100
25
K 52 65 75 95 110
25
125 125
M 312 320 325 335 345
L 82
N 312 325 330
115 115
O 83 83 83
340 350
83 83
120 120
P 125
Q 130 120 115
115 110
R 270 275 280
220,7 210,3
S 70 70 70
285 285
70 70
57,5 77,4
~ T 255,0
~ U 10,0 27,8 42,6
245,3 230,8
X 89,38 81,25 75,0 80,20 75,0
50 45 40 40 35
7979 79 79 79
46 46 46 46
J
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S03
-
Fhrungsklammer (L)Side Plate (L)
Fhrungsklammer (R)Side Plate (R)
SchieberfhrungCam Base
GasdruckfederGas Spring
Zwangsrckholer (L)Positive Return (L)
Bauteile / Components
AufnahmeplatteMounting Plate
TreiberCam Driver
Gleitplatte (A)Wear Plate (A)
HalteplatteStop Plate
PassfederFitting Key
AnschlagbolzenStop Bolt
DmpferDamping Element
Zwangsrckholer (R)Positive Return (R)
Gleitplatte (C)Wear Plate (C)
Gleitplatte (B)Wear Plate (B)
SchieberCam Slider
Lock Out StiftLock Out Pin
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S04
-
Stckliste / Component Parts
Damping Element
Positive Return (R)
Positive Return (L)
Gas Spring Ejector
Side Plate (L)
Side Plate (R)
Cam Base
Cam Slider
Cam Driver
Description Material
Code No.
Stop Plate
Wear Plate (C)
Mounting Plate
Stop Bolt
Fitting Key
Wear Plate (B)
Wear Plate (A)
Es ist darauf zu achten, dass der Schraubverschluss derGasdruckfeder unbedingt vor Inbetriebnahmeeingeschraubt und zustzlich eingeklebt werden muss!
It is important to ensure that the Screw Lock of the GasSpring is screwed in and secured with Loctite (or similar)before use!
Die Gewhrleistung erstreckt sich nur auf die kompletteSchiebereinheit.
The warranty is only extended to the complete cam unit.
Lieferumfang:Schiebereinheit, Pafedern, Lock Out - System
Scope of delivery:Cam unit, Fitting Keys, Lock Out - System
Ident-Nr.
Bezeichnung Material
Treiber
Schieber
Schieberfhrung
Fhrungsklammer (L)
Fhrungsklammer (R)
Gleitplatte (A)
Gleitplatte (B)
Gleitplatte (C)
Gasdruckfeder
Zwangsrckholer (L)
Zwangsrckholer (R)
Dmpfer
Aufnahmeplatte
Halteplatte
Anschlagbolzen
Passfeder
22554
0 5 10 15 20
22550 22551 22552 22553
0.7070 104351 104354 104357
104361 104363
0.7070 105870 105869 105868
104359 104362
105867 105866
23253 23253
0.7070 104353
WF 750/1A 23253 23253 23253
104356 104358
WF 750/1A 23254 23254 23254
18208 18208
WF 750/1A 18233 18233 18233
23254 23254
18233 18233
22008 22008
WF 750/1A 18208
1.7225 22008 22008 22008
18208 18208
DADCO 101570 101570 101570
104956 104956
1.7225 104957 104957 104957
101570 101570
104957 104957
101498 101498
1.7225 104956
PUR 101498 101498 101498
104956 104956
1.7225 105865 105865 105865
104723 104723
1.7225 105745 105745 105745
105865 105865
105745 105745
23390 23390
1.7225 104337
1.0503.07 23390 23390 23390
104337 104337
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S05
-
Lock Out Stift um Festsetzen des Schiebers verwenden!z
(nicht im Lieferumfang / )Use Lock Out Pin to lock the Cam!
not in scope of delivery
Lock Out Stift(nicht im Lieferumfang)Lock Out Pin(not in scope of delivery)
SchieberCam Slider
TreiberCam Driver
Gasdruckfeder SchlauchsystemGas Spring Linking
GasdruckfederGas Spring
Anschluss Adapter (2x)Port Adapter
SchlauchHose
Kontrollarmatur (1x)Mini Control Panel (1x)
Schlauch Adapter (2x)Hose Adapter (2x)
Lock Out - System
SchieberfhrungCam Base
AufnahmeplatteMounting Plate
Lock Out - System nur zum Festsetzen des Schiebers fr die Bearbeitung. Vor der Produktion entfernen!Use Lock Out - System only to lock the cam for processing. Remove before production!
Das Schlauchsystem ist gem der Einbauverhltnisse demWerkzeug anzupassen. Die Platzierung der Anschluarmaturenund der Verschlauchung erfolgt kundenseitig.
The Gas Spring Linking has to be adapted to the tool integration.The position of the Control Panel and the Hose Linking is on thepart of the customer.
Das gesamte Schlauchsystem ist ber die Fa. DADCO zubestellen.
The complete Gas Spring Linking has to be ordered from DADCO.
Wird diese Schiebertype an die Kontrollarmatur angeschlossen,ist in der Bestellung kein Hinweis auf die Anschlussmglichkeitntig.
If this type of cam is linked with the Control Panel, an advice to theconnectivity is not neccessary in the order.
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S06
-
Gleitplatte auf Schieber entfernenSchraube mit Unterlegscheibe herausdrehenAnschlagbolzen nach oben herausziehenSchraube der Verriegelungsplatte entfernenVerriegelungsplatte um 90 drehen und herausnehmenGasdruckfeder nach hinten herausziehen
Ausbau der Gasdruckfeder unter der Presse:01.02.03.04.05.06.
Removing the Gas Spring Ejector below the Press:01.02.03.04.
Remove Wear Plate from Cam SliderTurn out Screw and washerPull out the Stop Bolt upwardsRemove screw from Stop PlateTurn around the Stop Plate for 90 and removePull the Gas Spring Ejector backwards
05.06. Schieberbreite / Cam Unit Width + min. 140 mm
Der Ausbau darf nur im entspanntenZustand der Gasdruckfeder erfolgen!
Removing is only allowed for the extendedmoment of the Gas Spring Ejector!
Freiraum zum Wechsel der Gasdruckfeder / Free space for exchanging the Gas Spring Ejector
240mm
240 mm
Bei den seitlichen Fhrungsklammern ist auf Zugnglichkeit derBefestigungsschrauben und Stifte zur Klammereinstellung bzw. Demontagedes Schiebers zu achten. Empfehlung: Seitlicher Freiraum mindestens 70mm.Wenn dies aus Platzgrnden nicht mglich ist, muss der Schieberteil fr eineKlammernachstellung demontiert werden.
At the side plates take care of free access to the fixing screws and pins forplate adjustment resp. disassembly of the cam. Advice: free side areaminimum 70mm. If impossible in case of space reasons, the cam part has tobe disassembled for readjusting the Plate.
Alternative removing the Gas Spring Ejectorbelow the Press:01.02.03.
04.
Remove screw
Pull back Cam Slider with all attachment parts andremovePull the Gas Spring Ejector backwards
Turn around the Stop Plate for 90 and remove
Schraube entfernenHalteplatte um 90 drehen und herausziehenSchieber mit allen Anbauteilen nach hintenherausziehen und entfernenGasdruckfeder nach hinten herausziehen
Alternativer Gasdruckfeder-Ausbau unter der Presse:01.02.03.
04.
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S07
-
31 38 38 38 31
33 49 62 49 33
37 54 117 54 37
41 61 141 61 41
44 68 178 68 44
46 73 220 73 46
5x
20
25
10
110
110
3 x 2025
Die Schieberkaft wird gem Skizze weitergeleitet.The camforce is passed on according the diagram.
Abschulterung /
Presse / :Schieberfhrung / :
Treiber / :
Shouldering:
PressCam Base
Cam Driver
hh
HV
1
2
2
2
VH
1
1
(oben / )(unten / )
ertikalhorizontal(v )( )
(horizontal)(vertikal)
abovebelow
Erluterung / ):(Beispiel /Explanation Example
Ident NrCode No
Kraft im Mittelpunkt des FeldesForce in the centre of area
Wert der Kraft KNValue of Force KN
Hhe der berechnetenArbeitsflcheHeight calculatedWorking Area
Arbeitsflche obenWorking Area above
Breite der ArbeitsflcheWidth Working Area
grte Kraftmaximum force
BeschreibungDescription
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche / )
Acceptable Cam ForceView Working Area
Kraftverteilung / Force Distribution
Shouldering RetractilityAbschulterung Abstreifkraft
(KN)(mm)
100 %
80 %
60 %
40 %
20 %
0 %(0 KN)
Die Einfrbung der Krftediagramme erfolgtje Neigung im Wertebereich von 0% (0 KN)bis 100% (max. Schieberkraft).
The colouring of the diagrams is raised byevery bent in range of 0% (0 KN) to 100%(max. Cam Force).
Kraftverteilungfr max. Schieberkraft
(KN)
(KN)
SchieberWinkelCamAngle
max.Schieber
Kraftmax.Cam
Force
Force Distributionfor max. Cam Force
HS-UT 110-022550
V1 H1 V2 H2 h1 h2
00 o 220 187 223 187 0 140 25 2,5
05 o 220 206 206 186 14 130 25 2,5
10 o 195 198 166 164 26 120 25 2,5
15 o 203 206 173 170 27 100 25 2,5
20 o 195 198 138 131 45 80 25 2,4
V2
AbschulterungShouldering
V1
h1H1
SchieberkraftCam Force
AbstreifkraftRetractility
h2
Fr einen ruhigen Schieberlauf und lange Standzeiten der Gleitplattenwird empfohlen, den Kraftschwerpunkt mglichst in den Bereich desKraftzentrums zu legen.
For a smooth flow and a long life of the Wear Plates it is recommendedto lay the centre of gravity in the area of the centre of force.
The following diagrams illustrate, for each separate field, the possiblereceiving size of the camforce working not only in the centre of the fieldbut at the same time in the exact direction of course of the cam. Ifseveral forces work simultaneously the common centre of force has tobe specified and compared with the information of the tabular.
Die folgenden Tafeln zeigen fr jedes Feld die aufnehmbare Greeiner im Mittelpunkt dieses Feldes und genau in Laufrichtung desSchiebers wirkenden Schieberkraft. Bei mehreren auftretenden Krftenist deren gemeinsamer Kraftschwerpunkt zu ermitteln und mit denAngaben in der Tabelle zu vergleichen.
Alle eingeleiteten Krfte mssen immer niedriger ausfallen als dieTabellenangaben.
All incoming forces always have to be lower than the tabular values.
Die berbauung der Arbeitsflche ist ohne Rcksprache mitnicht zulssig.voestalpine
Reibungsverluste und andere die Laufkraft beeinflussendeGegebenheiten (Winkelstellung) sind in der Ermittlung derRckzugskrfte enthalten und bercksichtigt worden.
To overbuild the work space is not acceptable before consulting.alpinevoest
The friction loss and other data affecting the flow force (angle position)are contained in the determination of the retraction forces and havebeen considered.
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S08
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 110-022550
HS-UT 110-522551
HS-UT 110-1022552
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
31 38 38 38 31 31 38 38 38 31
33 49 62 49 33 33 49 62 49 33
37 54 117 54 37 37 54 102 54 37
41 61 141 61 41 41 61 102 61 41
44 68 178 68 44 44 68 102 68 44
46 73 220 73 46 46 73 102 73 46
31 38 38 38 31 31 38 38 38 31
34 49 62 49 34 34 49 62 49 34
37 54 117 54 37 37 54 111 54 37
41 61 142 61 41 41 61 111 61 41
44 68 178 68 44 44 68 111 68 44
46 73 220 73 46 46 73 110 73 46
30 32 32 32 30 30 32 32 32 30
32 47 49 47 32 32 47 49 47 32
36 52 90 52 36 36 52 90 52 36
39 58 130 58 39 39 58 122 58 39
42 65 161 65 42 42 65 122 65 42
45 70 195 70 45 45 70 122 70 45
110 110
3 x 2025
5x
20
25 25 3 x 20
10
110
25
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S09
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 110-1522553
HS-UT 110-2022554
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
25 25 25 25 25 25 25 25 25 25
33 36 36 36 33 33 36 36 36 33
36 53 59 53 36 36 53 59 53 36
40 59 119 59 40 40 59 119 59 40
45 68 166 68 45 45 68 131 68 45
48 74 203 74 48 48 74 131 74 48
25 25 25 25 25 25 25 25 25 25
33 36 36 36 33 33 36 36 36 33
36 53 59 53 36 36 53 59 53 36
40 58 119 58 40 40 58 119 58 40
45 67 165 67 45 45 67 133 67 45
47 74 195 74 47 47 74 133 74 47
105
x20
110
25 3 x 20 25 25 3 x 20 25
110 110
HSUT 0110 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S10
-
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S00
-
Technische Daten / :Specification
* Bestellbeispiel / : 22561 / HS-UT 150-05 / 75 HubOrder Example
Arbeitsflche / :Einbau / :Schieber / :Presskraft / (min.):
hhebreite
(Details siehe Diagramm / )
Working AreaClosed Height
Cam Unit WidthPress Force
For details see diagramm
Horizontalschieber /Baugre / : HS-UT 150-0 bis / 20
Horizontal CamType to
150 mm x 110 mm275 mm150 mm32 to
Ident-Nr.
Code No.
Bezeichnung:
Description:
Hub
Stroke
22560 HS-UT 150-00 75
22561 HS-UT 150-05 75
22562 HS-UT 150-10 75
22563 HS-UT 150-15 75
22564 HS-UT 150-20 75
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S01
-
3D Ansicht3D View
AblaufdiagrammCam Diagram
Draufsicht Treiber / Plan View Cam Driver
Ansicht XView X
Schnitt A-ASection A-A
Draufsicht Schieberfhrung / Plan View Cam Base
Gasdruckfederweg = HubGasspringway = Stroke
Bau
hhe
/C
lose
d H
eigh
t
X
Hub +2Stroke +2
FestsetzmaFix Measure
Konstruktions-EinfgepunktTooling-Ball
ArbeitsflcheWorking Area
Verschraubung
Auf Zugnglichkeitder Schrauben undStifte achten!
M16 (4x)Screw Connection
Take care for freeaccess to screwsand dowels!
Rd. 16H7 (2x)
A ARd. 16H7 (2x)
Verschraubung M16 (4x)Screw Connection
Auf Zugnglichkeit derSchrauben und Stifte achten!Take care for free access toscrews and dowels!
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S02
-
Mae / Measures
FestsetzmaFix Measure
Bauhhe / 0,2Closed Height
Retractility
Ident-Nr.Code No.
Cam Angle
GasdruckfederwegGas Spring Way
Abstreifkraft
GewichtWeight
Schieberwinkel
HubStroke
Alle nicht tolerierten Mae entsprechen ISO 2768 Mittel. Dimensions without tolerance are analog to ISO 2768 middle.
Stiftlcher werden mit 0,02mm Toleranz gefertigt. Dowel holes will be manufactured with 0,02mm tolerance.
Fr geringere Rckzugskrfte (z.B.: beim Einsatz einesseparaten Abstreifers auf dem Schieber) ist esempfehlenswert, den Druck der Gasdruckfeder zurSchonung der Presse oder Minimierung der elastischenVerformung im Werkzeugguss zu reduzieren (min.18 bar).
For lower retraction forces (for example when a separatestripper is mounted on the cam) it is recommandable toreduce the gas spring pressure (min. 18 bar) in order to sparethe press or minimize the elastic deformation in the tool cast.
F0 / F1 (KN): 4,7 / 6,6Presskraft Gasdruckfeder / :Gas Spring Force F0: Anfangskraft /F1: Endkraft /
starting forceending force
0 5 10 15 20
275 275 275 275 275
+ 0,06+ 0,04
61 60 61 62
22562 22563
5,4
22564
75 75
62
75 75 75
22560 22561
15
5,3
75 75 75 75 75
5,5 5,5 5,4
20
A 0,02 290 295 300 315 315
0 5 10
B 110 100 95
30 30
C 0,02 62 62 62
105 100
62 62
12 12
C1 0,02 30
C2 0,02 12 12 12
30 30
D 0,02 200 190 175
355 365
E 22 35 45
165 155
55 70
105 105
F 332
G 150 140 130
340 345
55
I 0,02 170 180 190 200 210
H 45 45
25 25 25
5555
90 100
25
K 52 65 75 95 105
25
125 125
M 312 320 325 335 340
L 82
N 312 325 330
120 115
O 120 120 120
340 345
120 120
125 120
P 125
Q 130 120 115
115 110
R 270 275 280
220,7 210,3
S 110 110 110
295 295
110 110
57,5 77,4
~ T 245,0
~ U 10,0 26,9 42,6
235,4 230,8
X 89,38 81,25 75,0 80,20 75,0
50 45 40 40 35
7979 79 79 79
J
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S03
-
Fhrungsklammer (L)Side Plate (L)
Fhrungsklammer (R)Side Plate (R)
SchieberfhrungCam Base
GasdruckfederGas Spring
Zwangsrckholer (L)Positive Return (L)
Bauteile / Components
AufnahmeplatteMounting Plate
TreiberCam Driver
SchieberCam Slide
HalteplatteStop Plate
Passfeder (A)Fitting Key (A)
AnschlagbolzenStop Bolt
DmpferDamping Element
Zwangsrckholer (R)Positive Return (R)
Gleitplatte (C)Wear Plate (C)
Gleitplatte (B)Wear Plate (B)
Gleitplatte (A)Wear Plate (A)
Lock Out StiftLock Out Pin
Passfeder (B)Fitting Key (B)
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S04
-
Stckliste / Component Parts
Damping Element
Positive Return (R)
Positive Return (L)
Gas Spring Ejector
Side Plate (L)
Side Plate (R)
Cam Base
Cam Slider
Cam Driver
Description Material
Code No.
Stop Plate
Wear Plate (C)
Mounting Plate
Stop Bolt
Wear Plate (B)
Wear Plate (A)
Fitting Key (A)
Fitting Key (B)
Gas Spring EjectorHose System
Wird der Schieber an das Schlauchsystemangeschlossen, mssen die Gasdruckfedern getauschtwerden.
In case of fitting the cam unit to the hose system, the GasSprings have to be exchanged.
Es ist darauf zu achten, dass der Schraubverschluss derGasdruckfeder unbedingt vor Inbetriebnahmeeingeschraubt und zustzlich eingeklebt werden muss!
It is important to ensure that the Screw Lock of the GasSpring is screwed in and secured with Loctite (or similar)before use!
Die Gewhrleistung erstreckt sich nur auf die kompletteSchiebereinheit.
The warranty is only extended to the complete cam unit.
Lieferumfang:Schiebereinheit, Pafedern, Lock Out - System
Scope of delivery:Cam unit, Fitting Keys, Lock Out - System
Ident-Nr.
Bezeichnung Material
Treiber
Schieber
Schieberfhrung
Fhrungsklammer (L)
Fhrungsklammer (R)
Gleitplatte (A)
Gleitplatte (B)
Gleitplatte (C)
Gasdruckfeder
GasdruckfederSchlauch /
Zwangsrckholer (L)
Zwangsrckholer (R)
Dmpfer
Aufnahmeplatte
Halteplatte
Anschlagbolzen
Passfeder (A)
Passfeder (B)
22563 22564
104436 104731
20
22560 22561
0 5 10 15
22562
104734 104737
0.7070 105885 105884 105823 105881 105880
0.7070 104428
0.7070 104426 104435 104729
23253 23253
WF 750/1A 23254 23254 23254
104732 104735
23254 23254
18237 18237
WF 750/1A 23253
WF 750/1A 18243 18243 18243
23253 23253
WF 750/1A 18224 18224 18224
101565 101565
1.7225 18312 18312 18312
18224 18224
22005 22005
105354 105354
DADCO 101565
DADCO 105354 105354 105354
101565 101565
1.7225 104957 104957 104957
101512 101512
1.7225 104956 104956 104956
104957 104957
104956 104956
105813 105813
PUR 101512
1.7225 105813 105813 105813
101512 101512
1.7225 105752 105752 105752
23390 23390
1.7225 104433 104433 105318
105752 105752
104976 104976
23391 23391
1.0503.07 23390
1.0503.07 23391 23391 23391
23390 23390
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S05
-
Lock Out Stift um Festsetzen des Schiebers verwenden!z
(nicht im Lieferumfang / )Use Lock Out Pin to lock the Cam!
not in scope of delivery
Lock Out Stift(nicht im Lieferumfang)Lock Out Pin(not in scope of delivery)
SchieberCam Slider
TreiberCam Driver
Gasdruckfeder SchlauchsystemGas Spring Linking
GasdruckfederGas Spring
Anschluss Adapter (2x)Port Adapter
SchlauchHose
Kontrollarmatur (1x)Mini Control Panel (1x)
Schlauch Adapter (2x)Hose Adapter (2x)
Lock Out - System
SchieberfhrungCam Base
AufnahmeplatteMounting Plate
Lock Out - System nur zum Festsetzen des Schiebers fr die Bearbeitung. Vor der Produktion entfernen!Use Lock Out - System only to lock the cam for processing. Remove before production!
The Gas Spring Linking has to be adapted to the tool integration.The position of the Control Panel and the Hose Linking is on thepart of the customer.
Das Schlauchsystem ist gem der Einbauverhltnisse demWerkzeug anzupassen. Die Platzierung der Anschluarmaturenund der Verschlauchung erfolgt kundenseitig.
Das gesamte Schlauchsystem ist ber die Fa. DADCO zubestellen.
The complete Gas Spring Linking has to be ordered from DADCO.
Wird diese Schiebertype an die Kontrollarmatur angeschlossen,ist in der Bestellung unbedingt ein Hinweis auf die Anschluss-mglichkeit ntig.
If this type of cam is linked with the Control Panel, it is absolutelynecessary to make a note of the connectivity in the order.
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S06
-
Schieberbreite / Cam Unit Width + min. 140 mm
Freiraum zum Wechsel der Gasdruckfeder / Free space for exchanging the Gas Spring Ejector
240mm
240 mm
Der Ausbau darf nur im entspanntenZustand der Gasdruckfeder erfolgen!
Removing is only allowed for the extendedmoment of the Gas Spring Ejector!
Bei den seitlichen Fhrungsklammern ist auf Zugnglichkeit derBefestigungsschrauben und Stifte zur Klammereinstellung bzw.Demontage des Schiebers zu achten. Empfehlung: SeitlicherFreiraum mindestens 70mm. Wenn dies aus Platzgrnden nichtmglich ist, muss der Schieberteil fr eine Klammernachstellungdemontiert werden.At the side plates take care of free access to the fixing screws and pins for plate adjustment resp. disassembly of the cam. Advice:free side area minimum 70mm. If impossible in case of space reasons, the cam part has to be disassembled for readjusting the Plate.
Gleitplatte auf Schieber entfernenSchraube mit Unterlegscheibe herausdrehenAnschlagbolzen nach oben herausziehenSchraube der Verriegelungsplatte entfernenVerriegelungsplatte um 90 drehen und herausnehmenGasdruckfeder nach hinten herausziehen
Ausbau der Gasdruckfeder unter der Presse:01.02.03.04.05.06.
Removing the Gas Spring Ejector below the Press:01.02.03.04.
Remove Wear Plate from Cam SliderTurn out Screw and washerPull out the Stop Bolt upwardsRemove screw from Stop PlateTurn around the Stop Plate for 90 and removePull the Gas Spring Ejector backwards
05.06.
Alternative removing the Gas Spring Ejectorbelow the Press:01.02.03.
04.
Remove screw
Pull back Cam Slider with all attachment parts andremovePull the Gas Spring Ejector backwards
Turn around the Stop Plate for 90 and remove
Schraube entfernenHalteplatte um 90 drehen und herausziehenSchieber mit allen Anbauteilen nach hintenherausziehen und entfernenGasdruckfeder nach hinten herausziehen
Alternativer Gasdruckfeder-Ausbau unter der Presse:01.02.03.
04.
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S07
-
37 48 57 57 57 48 37
48 69 101 101 101 69 48
61 87 114 238 114 87 61
78 99 132 308 132 99 78
79 106 146 392 146 106 79
79 112 158 472 158 112 79 10
110
5x
20
150
5 x 2025 25
Die Schieberkaft wird gem Skizze weitergeleitet.The camforce is passed on according the diagram.
Abschulterung /
Presse / :Schieberfhrung / :
Treiber / :
Shouldering:
PressCam Base
Cam Driver
hh
HV
1
2
2
2
VH
1
1
(oben / )(unten / )
ertikalhorizontal(v )( )
(horizontal)(vertikal)
abovebelow
Erluterung / ):(Beispiel /Explanation Example
Ident NrCode No
Kraft im Mittelpunkt des FeldesForce in the centre of area
Wert der Kraft KNValue of Force KN
Hhe der berechnetenArbeitsflcheHeight calculatedWorking Area
Arbeitsflche obenWorking Area above
Breite der ArbeitsflcheWidth Working Area
grte Kraftmaximum force
BeschreibungDescription
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche / )
Acceptable Cam ForceView Working Area
Kraftverteilung / Force Distribution
Shouldering RetractilityAbschulterung Abstreifkraft
(KN)(mm)
100 %
80 %
60 %
40 %
20 %
0 %(0 KN)
Die Einfrbung der Krftediagramme erfolgtje Neigung im Wertebereich von 0% (0 KN)bis 100% (max. Schieberkraft).
The colouring of the diagrams is raised byevery bent in range of 0% (0 KN) to 100%(max. Cam Force).
Kraftverteilungfr max. Schieberkraft
(KN)
(KN)
SchieberWinkelCamAngle
max.Schieber
Kraftmax.Cam
Force
Force Distributionfor max. Cam Force
HS-UT 150-022560
V1 H1 V2 H2 h1 h2
00 o 472 401 478 401 0 140 30 5,5
05 o 501 468 468 424 31 130 30 5,5
10 o 404 410 344 340 54 120 30 5,4
15 o 323 329 276 273 42 100 30 5,4
20 o 323 329 230 218 73 80 30 5,3
V2
AbschulterungShouldering
V1
h1H1
SchieberkraftCam Force
AbstreifkraftRetractility
h2
Fr einen ruhigen Schieberlauf und lange Standzeiten der Gleitplattenwird empfohlen, den Kraftschwerpunkt mglichst in den Bereich desKraftzentrums zu legen.
For a smooth flow and a long life of the Wear Plates it is recommendedto lay the centre of gravity in the area of the centre of force.
The following diagrams illustrate, for each separate field, the possiblereceiving size of the camforce working not only in the centre of the fieldbut at the same time in the exact direction of course of the cam. Ifseveral forces work simultaneously the common centre of force has tobe specified and compared with the information of the tabular.
Die folgenden Tafeln zeigen fr jedes Feld die aufnehmbare Greeiner im Mittelpunkt dieses Feldes und genau in Laufrichtung desSchiebers wirkenden Schieberkraft. Bei mehreren auftretenden Krftenist deren gemeinsamer Kraftschwerpunkt zu ermitteln und mit denAngaben in der Tabelle zu vergleichen.
Alle eingeleiteten Krfte mssen immer niedriger ausfallen, als dieTabellenangaben.
All incoming forces always have to be lower than the tabular values.
Die berbauung der Arbeitsflche ist ohne Rcksprache mitnicht zulssig.voestalpine
Reibungsverluste und andere die Laufkraft beeinflussendeGegebenheiten (Winkelstellung) sind in der Ermittlung derRckzugskrfte enthalten und bercksichtigt worden.
To overbuild the work space is not acceptable before consulting.alpinevoest
The friction loss and other data affecting the flow force (angle position)are contained in the determination of the retraction forces and havebeen considered.
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S08
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 150-022560
HS-UT 150-522561
HS-UT 150-1022562
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
37 48 57 57 57 48 37 37 48 57 57 57 48 37
48 69 101 101 101 69 48 48 69 101 101 101 69 48
61 87 114 238 114 87 61 61 87 114 145 114 87 61
78 99 132 308 132 99 78 78 99 124 145 124 99 78
79 106 146 392 146 106 79 79 106 124 145 124 106 79
79 112 158 472 158 112 79 79 108 123 145 123 108 79
44 56 67 67 67 56 44 44 56 67 67 67 56 44
56 82 113 120 113 82 56 56 82 113 120 113 82 56
75 97 128 279 128 97 75 75 97 128 158 128 97 75
86 108 149 344 149 108 86 86 108 138 158 138 108 86
91 116 165 427 165 116 91 91 116 138 158 138 116 91
95 124 180 501 180 124 95 95 123 138 158 138 123 95
32 39 44 44 44 39 32 32 39 44 44 44 39 32
42 56 72 72 72 56 42 42 56 72 72 72 56 42
53 80 103 142 103 80 53 53 80 103 142 103 80 53
70 90 118 268 118 90 70 70 90 118 175 118 90 70
78 99 134 332 134 99 78 78 99 134 175 134 99 78
79 104 145 404 145 104 79 79 104 145 174 145 104 79
25
10
110
5x
20
150 150
5 x 2025 25 25 5 x 20
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S09
-
Abschulterung /Absttzung oben und unten durch Abschulterung
Shouldering
Bracing above and below by shouldering
Zulssige Gre der Schieberkrfte /(Sicht auf Arbeitsflche /
Acceptable Cam ForceView Working Area)
HS-UT 150-1522563
HS-UT 150-2022564
Pafeder /
15 mmAbsttzung unten durch Passfederund oben durch Abschulterung:
Fitting Key
Bracing above by Fitting Keyand above by shouldering: 15 mm
18 21 22 22 22 21 18 18 21 22 22 22 21 18
23 28 30 30 30 28 23 23 28 30 30 30 28 23
30 38 43 43 43 38 30 30 38 43 43 43 38 30
41 57 71 71 71 57 41 41 57 71 71 71 57 41
61 89 120 161 120 89 61 61 89 120 161 120 89 61
80 102 141 323 141 102 80 80 102 141 187 141 102 80
18 21 22 22 22 21 18 18 21 22 22 22 21 18
23 28 30 30 30 28 23 23 28 30 30 30 28 23
30 38 43 43 43 38 30 30 38 43 43 43 38 30
41 57 71 71 71 57 41 41 57 71 71 71 57 41
61 90 121 161 121 90 61 61 90 121 161 121 90 61
81 103 143 323 143 103 81 81 103 143 210 143 103 81
105
x20
110
25 5 x 20 25 25 5 x 20 25
150 150
HSUT 0150 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S10
-
HSUT 0180 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S00
-
Technische Daten / :Specification
* Bestellbeispiel / : 22571 / HS-UT 180-05 / 75 HubOrder Example
Ident-Nr.
Code No.
Bezeichnung:
Description:
Arbeitsflche / (BxH):Einbau / :Schieber / :Presskraft / (min.):
hhebreite
(Details siehe Diagramm / )
Working AreaClosed Height
Cam Unit WidthPress Force
For details see diagramm
Horizontalschieber /Baugre / : HS-UT 180-0 bis / 20
Horizontal CamType to
180 mm x 120 mm300 mm180 mm52 to
22570 HS-UT 180-0 75
22571 HS-UT 180-5 75
22572 HS-UT 180-10 75
22573 HS-UT 180-15 75
22574 HS-UT 180-20 75
Hub
Stroke
HSUT 0180 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S01
-
3D Ansicht3D View
AblaufdiagrammCam Diagram
Draufsicht Treiber / Plan View Cam Driver
Ansicht XView X
Schnitt A-ASection A-A
Draufsicht Schieberfhrung / Plan View Cam Base
Gasdruckfederweg = HubGasspringway = Stroke
Bau
hhe
/C
lose
d H
eigh
t
X
Hub +2Stroke +2
FestsetzmaFix Measure
Konstruktions-EinfgepunktTooling-Ball
ArbeitsflcheWorking Area
Verschraubung
Auf Zugnglichkeitder Schrauben undStifte achten!
M16 (4x)Screw Connection
Take care for freeaccess to screwsand dowels!
Rd. 16H7 (2x)
A A
Rd. 16H7 (2x)Verschraubung M16 (4x)Screw Connection
Auf Zugnglichkeit derSchrauben und Stifte achten!Take care for free access toscrews and dowels!
HSUT 0180 EDITION 2006 voest alpine GIESSEREI LINZ GMBH
S02
-
Mae / Measures
FestsetzmaFix Measure
Bauhhe / 0,2Closed Height
Retractility
Ident-Nr.Code No.
Cam Angle
GasdruckfederwegGas Spring Way
Abstreifkraft
GewichtWeight
Schieberwinkel
HubStroke
Alle nicht tolerierten Mae entsprechen ISO 2768 Mittel. Dimensions without tolerance are analog to ISO 2768 middle.
Stiftlcher werden mit 0,02mm Toleranz gefertigt. Dowel holes will be manufactured with 0,02mm tolerance.
Fr geringere Rckzugskrfte (z.B.: beim Einsatz einesseparaten Abstreifers auf dem Schieber) ist esempfehlenswert, den Druck der Gasdruckfeder zurSchonung der Presse oder Minimierung der elastischenVerformung im Werkzeugguss zu reduzieren (min.18 ba