Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness...

13
KIT CONTENTS: Item Qty Part Number Description 50-GENK31 7 Pin Auto-Dimming Mirror with Compass, Temperature and Map Lamps 50-GENK41A 10 Pin Auto-Dimming Mirror with HomeLink ® 50-GENK45A 10 Pin Auto-Dimming Mirror with HomeLink ® and Compass 50-GENK51A 10 Pin Auto-Dimming Mirror with HomeLink ® Compass and Temperature 1 1 of the following: 50-GENK62 10 Pin Auto-Dimming Mirror with HomeLink ® , Compass and Temperature and Map Lamps Installation Parts Pack 7 Pin Harness Assembly with 3 Wires (Ignition, Ground and Battery) 2 1 of the following: Contact MITO Customer Service Installation Parts Pack 10 Pin Harness Assembly with 3 Wires (Ignition, Ground and Battery) 3 4 -- T-Tap Connectors (2 Red 18 – 22 AWG, 2 Blue 14 – 18 AWG) 4 5 -- Short Tie Wraps Not shown 1 -- Installation Instructions Not shown 1 -- User Guide Not shown 1 -- Warranty Card * Mirrors Equipped with Temperature Feature: 5 5 -- Long Tie Wraps 6 1 -- Temperature Sensor Temperature Sensor Harness (7 Pin Applications) 7 1 of the following: -- Temperature Sensor Harness (10 Pin Applications) * Optional Items (Not Included with Installation Kit) 8 1 -- Wire Cover HOMELINK ® AND THE HOMELINK HOUSE ® ARE REGISTERED TRADEMARKS OF JOHNSON CONTROLS, INC TOOLS REQUIRED: Safety Glasses Utility Knife Pliers #2 Phillip's Screwdriver Clean Rag Electrical Tape 4mm Flat Screwdriver Flashlight DC Voltmeter Fish-Wire (Coat Hanger) #T20 Torx Driver Panel Removal Tool Gentex by MITO Corporation Installation Instructions Page 1 of 13 Revision A 550-0427

Transcript of Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness...

Page 1: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

KIT CONTENTS: Item Qty Part Number Description

50-GENK31 7 Pin Auto-Dimming Mirror with Compass, Temperature and Map Lamps 50-GENK41A 10 Pin Auto-Dimming Mirror with HomeLink® 50-GENK45A 10 Pin Auto-Dimming Mirror with HomeLink® and Compass 50-GENK51A 10 Pin Auto-Dimming Mirror with HomeLink® Compass and Temperature

1 1 of the following:

50-GENK62 10 Pin Auto-Dimming Mirror with HomeLink® , Compass and Temperature and Map Lamps Installation Parts Pack 7 Pin Harness Assembly with 3 Wires (Ignition, Ground and Battery) 2 1 of the following:

Contact MITO Customer Service Installation Parts Pack

10 Pin Harness Assembly with 3 Wires (Ignition, Ground and Battery) 3 4 -- T-Tap Connectors (2 Red 18 – 22 AWG, 2 Blue 14 – 18 AWG) 4 5 -- Short Tie Wraps

Not shown 1 -- Installation Instructions Not shown 1 -- User Guide Not shown 1 -- Warranty Card * Mirrors Equipped with Temperature Feature:

5 5 -- Long Tie Wraps 6 1 -- Temperature Sensor

Temperature Sensor Harness (7 Pin Applications) 7 1 of the following: -- Temperature Sensor Harness (10 Pin Applications) * Optional Items (Not Included with Installation Kit)

8 1 -- Wire Cover

HOMELINK® AND THE HOMELINK HOUSE® ARE REGISTERED TRADEMARKS OF JOHNSON CONTROLS, INC

TOOLS REQUIRED: Safety Glasses Utility Knife Pliers #2 Phillip's Screwdriver Clean Rag Electrical Tape 4mm Flat Screwdriver Flashlight DC Voltmeter Fish-Wire (Coat Hanger) #T20 Torx Driver Panel Removal Tool

Gentex by MITO Corporation Installation Instructions

Page 1 of 13 Revision A 550-0427

Page 2: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

Perform the following pre-installation steps: 1. Place kit components on a clean, padded surface. 2. Record your programmed radio stations. 3. Remove driver side scuff plate. (Fig. 1) 4. Remove driver side door seal. (Fig. 2)

5. Remove driver side kick plate / cowl cover. (Fig. 3) 6. Remove driver side grab handle if equipped. (Fig. 4) 7. Remove driver side A-pillar trim. (Fig. 5)

INSTALLATION PRECAUTIONS / NOTES: Do not use excessive force when removing OEM mirror from windshield. Do not push fish-wire too far into dash to avoid damage to existing components. Do not place wire harness against objects with sharp edges that may cause electrical shorting. On vehicles equipped with A-pillar (side impact or SRS) airbags, verify mirror harness path remains

clear of airbag. Harness should follow and be secured to, existing OEM wiring with tie wraps. Verify that auto-dimming mirror harnesses do not interfere with brake, clutch, emergency brake or air

bag

1

2

3

4

5

1 Preparation

Page 2 of 13 Revision A 550-0427

Page 3: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

Page 3 of 13 Revision A 550-0427

8. Remove OEM mirror. (Fig. 6,7 or 8) a) Loosen #T20 torx screw on mirror mount and slide mirror upwards off from windshield button. (Fig. 6)

- - OR - - b) Insert 4mm into opening at bottom of mirror mount to disengage

locking tab and slide mirror upwards off from windshield button. (Fig. 7)

NOTE: Gently wiggling mirror while sliding upwards will assist removal.

- - OR - -

c) Insert panel removal tool into opening at bottom of mirror mount to disengage locking tab and slide mirror upwards off from windshield button. (Fig. 8)

NOTE: Gently wiggling mirror while sliding upwards will assist removal.

1. Attach auto-dimming mirror. a) Hold the mirror and slide the mirror downwards over wind-shield button until fully seated. (Fig. 9) b) Using #T20 torx driver, tighten the mirror mounting bracket screw to 1.3 ft-lbs (17.8 kg-cm). DO NOT OVERTIGHTEN NOTE: You will need to find a supply wire in your vehicle that provides +12V when vehicle is running or the key is in the ON or ACC position. You will also need to find a supply wire that provides +12V constant power when vehicle is both ON and OFF. Your automotive repair shop may sometimes be able to advise readily available locations for connecting to these power sources. A TIP: The cigarette lighter or power port receptacle may be a source of

switched +12V or constant +12V, depending on vehicle make. 1. Locate ignition (+12V switched) wire.

a) Using a multi-meter, find a wire exiting the fuse block or junction block that tests +12V and is controlled by the ignition switch. Operate vehicle accessories (power windows, door locks, power mirrors, etc.) to ensure that voltage does not drop on this wire. (Fig. 10)

b) Ensure power in this wire is off when vehicle key is OFF and label wire "IGNITION."

2 Auto-Dimming Mirror Installation

CAUTION

! CAUTION

! Do not use excessive force. Damage to windshield could occur. 6

3 Route Auto-Dimming Mirror Harness to Vehicle Power

1.3 ft-lbs

8

9

10

7 CAUTION

!

Page 4: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

11

12

13

14

15

16

2. Locate constant power (+12V constant) wire. a) Using a multi-meter, find a wire exiting the fuse block that tests +12V with vehicle ignition in the ACC, ON and OFF positions. (Fig. 11) b) Ensure power in this wire is still present when vehicle key is OFF and label wire "CONSTANT." 3. Disconnect vehicle's negative battery terminal. (Fig. 12) 4. Plug auto-dimming mirror harness into back of mirror. (Fig. 13) 5. Route harness up to vehicle headliner. (Fig. 14) a) Install optional wire cover (if purchased). (Fig. 15) 6. Route haress across vehicle headliner to top of A-pillar on side of

vehicle where vehicle connection wires / fuse block were found.

a) Use panel removal tool to ensure harness is tucked between headliner and roof of vehicle. (Fig. 16)

Page 4 of 13 Revision A 550-0427

Page 5: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

7. Route harness down A-pillar. (Fig. 17) NOTE: Harness will be secured later in installation procedure. 8. Route harness to vehicle connection wires. a) Using fish-wire, route harness from base of A-pillar through dash and into connection wire / fuse block area. (Fig. 18) 9. Attach wire tap to vehicle wire marked IGNITION. a) Center blade of wire tap on IGNITION wire and close wire tap with pliers. (Fig. 19) b) Ensure both halves of wire tap are closed completely and locking tab is engaged. 10. Connect auto-dimming mirror harness switched power wire to

vehicle wire marked IGNITION.

a) Locate the harness wire with WHITE STRIPE. b) Insert spade terminal on WHITE STRIPE wire into the wire tap on the vehicle wire labeled IGNITION. (Fig. 20) 11. Attach wire tap to vehicle wire marked CONSTANT. a) Center blade of wire tap on CONSTANT wire and close wire tap with pliers. (Fig. 21) b) Ensure both halves of wire tap are closed completely and locking tab is engaged. 12. Connect auto-dimming mirror harness constant power wire to

vehicle wire marked CONSTANT.

a) Locate the SOLID BLACK harness wire with spade terminal. b) Insert spade terminal on SOLID BLACK wire into the wire tap on the vehicle wire labeled CONSTANT. (Fig. 22)

18

17

20

21

22

19

Page 5 of 13 Revision A 550-0427

Page 6: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

Page 6 of 13 Revision A 550-0427

13. Connect auto-dimming mirror harness ground wire. a) Locate a ground bolt near connection / fuse block area and remove. NOTE: Bolt locations may vary but common locations are in the kick plate / cowl cover area or parking brake release handle. b) Install ring terminal of harness over bolt and reinstall. (Fig. 23) NOTE: If auto-dimming mirror is not equipped with outside temperature feature, skip to section 5 "Secure Harness Wires." 1. Mount temperature sensor. a) Remove splash guard panels if necessary to gain access to the area behind front bumper. b) From inside engine compartment, route sensor end of temperature harness down in front of radiator to area behind front bumper. (Fig. 24) c) Locate a mounting area for the temperature sensor in vehicle grille or bumper opening. This area should be as far away from the front of the radiator as possible while still allowing for free airflow around sensor. (Fig. 25) d) Slide sensor clip over edge of bumper or grille. (Fig. 26) e) Ensure clip is fully engaged to bumper or grille and that sensor secure. f) Replace splash guard if removed. 2. Locate routing point for temperature harness wire on vehicle

firewall. (Fig. 27 or 28)

a) Locate a rubber grommet in firewall that passes through to passenger compartment and cut a small "X" through it. (Fig. 27)

- - OR - - b) Locate hood latch cable grommet in firewall. (Fig. 28)

4 (Optional) Temperature Sensor Installation and Routing

CAUTION

!

24

25

27

28

26

23

CAUTION

! Do not slice outer sealing lip of grommet.

Page 7: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

Page 7 of 13 Revision A 550-0427

3. Route temperature harness to grommet in firewall. a) Route harness from radiator area, alongside fender to grommet in firewall. (Fig. 29) b) Secure harness to vehicle harnesses in engine compartment with long wire ties. (Fig. 30) 4. Route temperature harness into passenger compartment. a) From inside passenger compartment of vehicle, insert fish-wire through cut in firewall grommet or cable opening in hood latch

cable grommet, and into engine compartment.

b) Bend approximately 3 inches of harness at terminal end. c) Slide plastic sleeve (supplied in installation kit) over bent end of harness, covering harness terminals. (Fig. 31) d) Using electrical tape, secure fish-wire, to harness and sleeve. (Fig. 32) e) Pull harness through grommet and into passenger compartment. (Fig. 33) f) Remove tape and sleeve from harness. g) Inside engine compartment, leave extra wire for drip loop in front of grommet. h) Apply silicone sealant to grommet where harness wire passes through, to seal opening. 5. Route temperature harness to auto-dimming mirror. a) Route harness through dash up to base of A-pillar. (Fig. 34)

CAUTION

!

CAUTION

!

30

31

32

34

33

29

CAUTION

! Ensure routing path is clear of any moving engine parts.

CAUTION

! Do not route harness near areas of high engine heat.

CAUTION

! Temperature harness terminals are fragile. Use care not to damage.

Page 8: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

Page 8 of 13 Revision A 550-0427

b) Route harness up A-pillar. (Fig. 35) c) Route harness across vehicle headliner and down to auto-dimming mirror. (Fig. 36) d) Conceal harness wires under optional wire cover if used. 6. Connect temperature harness to auto-dimming mirror connector. a) Unplug connector from back of auto-dimming mirror. b) Using a 4mm screwdriver, pry the side tabs of the mirror connector, upwards to release the white locking tab. (Fig. 37) c) Insert terminals from temperature harness into pins #1 and #2 of mirror connector. (Fig. 38) NOTE: Temperature harness wires are not polarity sensitive so either terminal can be plugged into either opening on connector. d) Plug connector back into auto-dimming mirror. e) Ensure mirror has full rotation before proceeding to next step. 1. Secure all harness wires in A-pillar. a) Secure auto-dimming mirror harness wire(s) to vehicle harness in A-pillar with 3 short tie wraps. (Fig. 39)

5 Secure Harness Wires.

35

36

37

38

CAUTION

CAUTION

! Do not secure harness wires to any airbag components in A-pillar.

! Ensure harness wires do not obstruct A-pillar airbag.

CAUTION

! Do not secure harness wires to any drain tubes in A-pillar CAUTION

!

39

Page 9: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

Page 9 of 13 Revision A 550-0427

2. Bundle any excess harness wire(s) in kick-plate / cowl cover area

and connection wire / fuse block area and secure with remaining short tie wraps. (Fig. 40)

1. Reconnect negative battery cable. 2. Turn the ignition switch ON/ACC position. 3. With the vehicle in a fairly well-lit area, perform the following:

a) To make sure the auto-dimming feature is on, verify that the green LED to the left of the center switch is on. If it is not on, push the switch to turn the green LED on.

b) Cover the forward looking photocell on the back of mirror with a

dark cloth or towel. (Fig. 41) In a few seconds, the mirror will begin to darken. NOTE: Time to darken will vary with ambient light level. c) Remove the cover from the forward looking photo cell and the

mirror will begin to clear. d) Verify that either a direction, such as NE, or “CAL” is displayed

in the display window. If not, ensure the feature is turned ON by pressing the button.

e) Verify that a temperature is displayed in the display window (if

equipped). If not, ensure the feature is turned ON by pressing the button.

4. Turn the ignition key to the OFF position. 5. Push each HomeLink® button (if equipped), one at a time, and verify that LED indicator to the left of the center switch illuminates

with a red LED. (Fig. 42)

6. If mirror is equipped with maplights, push each maplight button to ensure lights are operational. (Fig. 43) 7. Testing is now complete.

CAUCAUTION

!

TION

! Ensure all wires being secured are clear of pedal and steering assemblies.

40

6 Testing.

41

Red LED

HomeLink Buttons

42

Maplight Buttons

43

Page 10: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

Page 10 of 13 Revision A 550-0427

1. Adjust compass zone after EC mirror installation. a) The zone setting is factory preset to Zone 8. Refer to Compass

Calibration Zone Map to find correct compass zone setting for your geographical location. (Fig. 44)

b) To change the zone setting, push and hold the button until

a number appears in the display. Press button repeatedly until desired compass zone number is reached.

1. Calibrate compass. a) Drive to an open, level area, away from large metallic objects or

structures. b) Hold the button for approximately 9 seconds until “CAL”

or "C" text appears in the display. Release the button to enter the calibration mode.

c) Drive slowly in up to 3 circles until the “CAL” or "C" text disappears, and a directional heading is displayed.

The compass is now calibrated.

7 Compass Zone Adjustment

1

2

3

4

5

67 8

9

1011

12

13

14

1523

45

6 7 8 9 10 11 1213

14

44

8 Compass Calibration

Page 11: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

Page 11 of 13 Revision A 550-0427

1. To change display from degrees Fahrenheit to degree Celsius.

a) Push and hold the button for 3 seconds until the display blinks “°C” or “°F”.

b) Release then toggle the button to select desired display mode. c) After 5 seconds of no button activity, the display will be set and will return to normal temperature reading.

2. Ice feature display. a) When outside temperature is 38° or lower, the display will read, "ICE" to alert driver of potential driving hazards.

To Operate the HomeLink® Feature: Please refer to the programming instructions outlined in this manual or: a) Visit the HomeLink® website at www.homelink.com b) Call the HomeLink® customer support line at 1-800-355-3515 WARNING! Before programming HomeLink® to a garage door opener or gate operator, make sure that people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener, it is advised to park outside of the garage. Do not use HomeLink® with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door that cannot detect an object – signaling the door to stop and reverse – does not meet current U.S. federal safety standards. For more information, contact HomeLink® at www.homelink.com or by calling 1-800-355-3515.

1. To begin, press and hold the 2 outer HomeLink® buttons (to clear memory) until the indicator light (LED) blinks slowly (approximately 20 seconds). (Fig. 45)

2. Release both buttons.

NOTE: Do not hold the buttons for longer than 30 seconds. Do not repeat this step when programming additional devices to

remaining buttons.

3. Position the end of the hand-held transmitter 1-3 inches away from the HomeLink® button you wish to program while keeping the indicator light in view. 4. Simultaneously press and hold both the chosen HomeLink® and hand- held transmitter buttons. (Fig. 46) Do not release the buttons until step 5 has been completed.

9 Temperature Feature (if equipped)

10 HomeLink® Feature and Programming Instructions

● Press and Hold for 20s seconds… ● LED blinks slowly… ● Release buttons

45

● Press and hold both… ● LED blinks fast… ● Release both buttons

46

Page 12: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

Page 12 of 13 Revision A 550-0427

NOTE: Some gate operator and garage door openers may require you to

replace this Programming step 4 with procedures noted in the “Gate Operator / Canadian Programming” section.

5. After the HomeLink® indicator light changes from a slow to a rapidly blinking light, release both the HomeLink® and hand-held transmitter

buttons.

6. Press and hold the just-trained HomeLink® button and observe the indicator light.

If the indicator light blinks rapidly for 2 seconds and then turns to a constant light, the device being programmed utilizes rolling code and programming is not complete until the following steps are completed. (Fig. 47)

7. On the garage door opener receiver (motor-head unit) locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor- head unit.

8. Firmly press and release the “learn” or “smart” button. (Fig. 48)

NOTE: You have 30 seconds to initiate step 9. 9. Return to the vehicle and firmly press, hold for 2 seconds and release the programmed HomeLink® button. (Fig. 49)

10. Repeat the “press/hold/release” above a second time and possibly a third time (depending on brand of device).

HomeLink® should now activate your rolling code equipped device.

Gate Operator / Canadian Programming: Canadian radio-frequency laws require transmitter signals to “time-out” or quit after several seconds of transmission – which may not be long enough for HomeLink® to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. If you live in Canada or you are having difficulties programming a gate operator by using the “Programming” procedures (regardless of where you live), replace “Programming HomeLink® step 4 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent possible overheating. 4. Continue to press and hold the HomeLink button while you press and

release - every 2 seconds (“cycle”) your hand-held transmitter until the frequency signal has successfully been accepted by HomeLink. (The indicator light will flash slowly and then rapidly.)

Proceed with “Programming” step 5 to complete. Erasing All Programmed HomeLink Buttons: Press and hold the two outer HomeLink buttons (as shown in Fig. 1), releasing only when the HomeLink indicator light begins to flash after 20 seconds. Do not hold for longer than 30 seconds.

● Press button… ● Fast blink for 2 seconds then constant = rolling code… ● Continue programming instructions

47

● Press “Learn” button… ● 30 SECONDS TO GET TO VEHICLE

48

● Hold for 2 seconds and release

49

If you have any questions or are having difficulty programming

your HomeLink® buttons, please refer to www.homelink.com or

call 1-800-355-3515.

Page 13: Gentex by MITO Corporation - College Hills · PDF fileConnect auto-dimming mirror harness switched power wire to ... pry the side tabs of the mirror ... Do not secure harness wires

TROUBLESHOOTING PROBLEM SOLUTION 1 "C" or "CAL" is displayed in display window Perform calibration sequence (ref. Sec. 8)

Perform compass zone setting procedure (ref. Sec. 7)

2 Inaccurate compass direction

Vehicle magnetics may have changed. Perform calibration sequence (ref. Sec. 8) NOTE: Installing items such as a ski rack, antenna, luggage rack or recent body repair can cause changes to the vehicle's magnetic field. Ensure connector is plugged into back of mirror. Ensure harness wires are connected to vehicle wires. 3 Mirror does not dim Ensure nothing is blocking sensor on front of mirror or its viewing path to the rear window of vehicle.

4 Mirror dims constantly Ensure nothing is blocking forward-looking sensor on back of mirror.

5 Cannot program garage door opener or other remote control device

Contact HomeLink® at 1-800-355-3515 or visit www.homelink.com for more information.

6 Temperature display is reading significantly low

Temperature display is set to degrees Celsius. Switch to degrees Fahrenheit (ref. Sec. 9)

7 Temperature display is reading too high or rises after starting vehicle

Temperature sensor is located in an area of high heat or low airflow. Move sensor to different location in vehicle grill area.

8 Temperature is reading -20 degrees F or lower

Turn ignition off for 2.5 hours. Do not unplug mirror.

9 Display window shows "SC" (short circuit) Indicates Short Circuit. Check all power wires to mirror for breaks, crimps or slices. Repair wires with electrical tape. Temperature sensor wires are not connected properly to mirror connector. Check connection to mirror connector. Temperature sensor wire(s) crimped or broken. Check wires and repair with electrical tape. 10 Display window shows "OC" (open circuit)

Temperature sensor is not plugged into harness. Check connection and ensure sensor is fully plugged into harness.

For all other questions, please contact MITO Corporation at 1-800-433-6486

Page 13 of 13 Revision A 550-0427