7/31/2019 Gb Copy-control Free

1/2

GB COPY-CONTROL

P1

FUNCTION BUTTON

This button can activate one of the three functions, besides,

in the FUNCTION 3, it conrm right memorisation of the

code.

P2

ENTER BUTTON/ ESC/ MEMORISATION

This button can conrm or not conrm one of the functions,

previously selected, with the button P1, besides, in the

FUNCTION 3, it needs to memorize the code inside the

machine and it can be choosen to transmit the memorized

code.

COPY-CONTROLGB_COPY-CONTROL_160909_VX8503

FUNCTION 1: frequency reader in Mhz

FUNCTION 2: frequency adjuster of the

oscillator (maximum value

is 1024)

FUNCTION 3: memorisation of the remote

controls code and check of the

right memorization of

the original remote control

indicating the right percentage

of the good learning.

FUNCTION 3bis: Transmission of the code

between the

COPY-CONTROL and

the copied remote control.

(between 250 and 869 Mhz).

The right position of the remote control is indicated in the picture

1 area 1, we recommend to nd the position of the antenna of

the remote control, normally it is in the lower part of the remote

control but it is not always the technical structure and the design of

the remote control , and vice versa, so we can nd the antenna in

another position. When you press the button of the remote control

the two RED L.E.D. of the COPY-CONTROL start ashing fast,

indicating the begining of the reading.

In particular the reading of the frequency is precise from 250 Mhz

to 869 Mhz

FUNCTION 1

Functions

1 - 2 - 3

Pressing repeatedly the P1 you will see numbers which

indicate the three functions available:

When you give power supply to the COPY-CONTROL (12VAC/DC), it turns on automatically and you can see a number on

the display for a while, this indicate the number of the software. (For example after the FUNCTION NO.1).

Select the FUNCTION no.1 with the button and keep pressed till you see in the display the number 1.P1 Press the button P2 to conrm the operation and go in the program.

When you are in this function you can read an adjust the frequencies without going out or enter in the same functions.

To go out press the button esc P2.

7/31/2019 Gb Copy-control Free

2/2

When you get near the remote control like in the shown position

of the picture (the oscillator should be already plugged in) press

the button with a pencil and turn slowly the potentiometer with a

ceramic screw-driver.The COPY-CONTROL show a rst adjustment level and the better

one is 1023.

We suggest you to put the remote control as near as you can in

the COPY-CONTROL and then remove it 3-5 cm to reach the

value 1024. We recommend not turn strong the potentiometer but

do it slowly.

To go out press the button esc P2.

FUNCTION 2

Put the antenna on the remote X to check like in the photo. Then press the button of the copy remote control to check if it has

well copied the code. When the COPY-CONTROL take the radio signal, the two REDLIGHTSashfaster. The right learning

of the remote control will be conrmed from the turning on of the YELLOW LIGHTS and the simultaneously showing on in the

display of the 100%. (TheYELLOW L.E.D. will turn on only when the code is 100% copied)

Release the button P2.

FUNCTION 3

Pay attention that this function reachable only if you are already in the FUNCTION no.3 and after learning a code in the

memory of the COPY-CONTROL. In this situation if you press the button P2 , keep it pressed, conrm it pressing and re

leasing the P1, (P2+P1 and then release). After this operation you have a constantly transmission of the memory code,

this is conrmed when a ashing twill be displayed as shown in the picture.

Now, putting a remote control as shown in the picture, we can clone that code directly from the COPY-CONTROL, to make

easy the copy of the remote control which have the same code and besides this is useful in case of difcult copy because

you can hang on the better sensitivity of the COPY-CONTROL.

FUNCTION 3/Bis

Nologo srl declares that COPY-CONTROL is conformed to the essential requirements of the following norms:

ETSI EN 301 489-3 EN 300 220-1 EN 300 220-3 EN 60950: 1997

Me Ernestino Bandera the administrator, declares that the remote control has been tested in a typical installation and satises all

essential requirements of the directives: 99/5/CEErnestino Bandera

Busto Arsizio, 01.10.2008

ConformityDeclaration

2002/95/EC

RoHSC O M P L I A N T

To select the function 2 with the button P1 , keep it pressed until youll see in the display the code in the picture.

Press the button P2 to enter in the program.

Now the COPY-CONTROL is ready to receive a signal of a remote control (low frequencies) to display the adjustment level.

Choose the function no.3 with the button P1 and keep it pressed till in the display you see the same number as in the picture.

Press and keep pressed the button P2 to memorize in the COPY-CONTROL the original code X.

Now the COPY-CONTROL that has already memorize the remote

control , now it can compare the code with the next one Y.

Put the remote control Y and press the button and check it.

If the transmitted code is the same of the previous learned remote

control, the YELLOW L.E.D. and the percentage of the right

memorization the l.e.d. will turn on in the same time..

If the copy of the remote control hasnt copied 100% well the code

the blue lights will turn on and a low percentage (less then 100%) the

code is different of the previously memorized.

If we test with a rolling code remote control we can check that the learning and the comparison with the same button will give a

negative result (BLUE L.E.D. and low percentage) to conrm that it is a rolling code and it cannot be copied.

This is not valid for the xed part of the code which can be indicated in the percentage of the code (rolling code)