Gazebo GZ3 Aluminium - Shed Nation · The gazebo is secured with pegs into holes cast with...
Transcript of Gazebo GZ3 Aluminium - Shed Nation · The gazebo is secured with pegs into holes cast with...
of 201www.stcny.com
Systems Trading Corporation450 7th Avenue Suite 2809, New York, NY 10123Customer service: (877)782 4482 Email: [email protected]
5
12’
7’
8’11”
Assembly Instructions
Gazebo GZ3 Santa MonicaAluminium Composite Roof Panels
13’2”9’11”
of 202www.stcny.com
IntroductionThank you for purchasing the Gazebo GZ3. When properly assembled and maintained, this gazebo will provide many years of enjoyment!
These instructions include helpful hints and important information needed to safely assemble and properly maintain the gazebo. Please read these instructions completely before you begin.
Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of four people. The assembly should take about two hours.
Before Starting Assembly: CAREFULLY READ ALL THE INSTRUCTIONS BEFORE YOU BEGIN AND FOLLOW THE STEPS IN THE ORDER THEY ARE PRESENTED.
1. Make sure you have all the necessary parts: Compare the contents of the three cartons to the List of Parts. If any parts are missing or damaged, or you have any questions, please contact Customer service: (877)782 4482 or by email at [email protected] before beginning assembly.
2. Lay the parts out in separate staging areas: The List of Parts has the corresponding step number referenced to each part. We recommend that while you go through the list, make staging areas for each step and place the parts necessary for each step in these areas. This will save you time and effort during assembly.
3. Select a Location: When selecting a location for your gazebo, a flat level area is essential and if possible with proper water drainage and easy access to power and water, if neccessary. Choose a sunny, level position away from overhanging trees and power lines and protected from the wind as much as possible. Locate underground pipes or cables before preparing the site or anchoring the gazebo. Note: You may assemble the gazebo on a hard level surface and move it to its final location when finished. Make sure that there are no obstacles between the assembly area and the final position.
4. Prepare a Foundation: After choosing a location, proper preparation of the site is recommended. The site must be level. If the site is not level, create a base slightly larger than the outside dimensions of the gazebo using a perimeter of two by fours filled with either soil, sod or gravel. Make sure the base is square by measuring the diagonals from both directions and making sure they are equal. The gazebo is secured with pegs into holes cast with concrete. If you decide to have a concrete base, it is best to contact a reliable contractor to make sure it is flat and level. Make sure you have checked with your local authorities regarding any required building permits.
5. Make sure you have the proper tools: • Tape Measure • 2 Small Step Ladders • Work Gloves • Wooden Mallet • Safety goggles • Scissors • Phillips Screwdriver • Liquid soap or WD40 Lubricant • Spirit Level • Hex Key (included)
NOTE: A cordless drill with Phillips head bit is highly recommended but not essential.
of 203www.stcny.com
Safety Advice• The gazebo must be positioned and fixed
on a flat level surface.• Dispose of all plastic bags safely. Keep
them out of the reach of children.• Keep children and pets away from the
assembly area until the work is completed.• Always wear shoes, gloves and safety
goggles when working.• Take special care not to touch overhead
power lines with the aluminium profiles.• Do not attempt to assemble the gazebo in
windy or wet conditions.• Do not position your gazebo in an area
exposed to excessive wind. • If using power tools or a ladder, always fol-
low the manufacturers safety instructions. • Hot items such as recently used grills,
blowtorches etc. must not be stored in the gazebo.
• Make sure the gazebo complies with local building codes.
1
11
23
4
6
Table of ContentsIntroduction.............................................. 2Table of Contents...................................... 3List of Parts............................................... 4 Step 1 Assembling the Corner Profiles......... 6 Step 2 Assembling the Rails....................... 8 Step 3 Attaching the Rails to theCorner Profiles...... 10 Step 4 Securing the Gazebo to the ground.... 12 Step 5 Installing the Roof Gables.................. 13Step 6 Installing the Upper Roof Panels..... 16Step 7 Installing the Lower Roof Panels..... 18Step 8 Tightening the Screws on Roof Profiles... 19
General Order of AssemblyStep 1: Assembling the Corner profilesStep 2: Assembling the RailsStep 3: Attaching the Rails to the Corner ProfilesStep 4: Securing the gazebo to the groundStep 5: Installing the Roof GablesStep 6: Installing the Upper Roof PanelsStep 7: Installing the Lower Roof PanelsStep 8: Tightening the Screws on Roof Profiles
5
7
8
of 204www.stcny.com
List of PartsThe gazebo is shipped in three cartons. These cartons are heavy. Be careful when lifting them.Wear proper safety gear including work shoes, gloves and goggles.The parts are identified by removable stickers.Place all the parts for each step in staging areas, checking that you have all parts as you go.If any parts are missing or damaged, contact STC customer service before beginning assembly:Customer service: (877)782 4482 Email: [email protected]
Inner Roof Connector
No. Profile Qty Step
1 4 1
2 4 1
3 4 1
4 4 1
5 2 2
6 2 2
7 2 2
8 2 2
9 6 2
No. Profile Qty Step
10 10 2
11-111-2
22 5
12-112-2
42 5
13 4 7
14 4 7
15 2 6
16 2 6
17 2 6
18 2 6
2190mm
2082mm
1907mm
1582mm
1407mm
Corner Profile
Support Frame
Support Plate
Corner Roof Connector
Long Rail
Long Rail
Short Rail
Short Rail
Outer Roof Connector
Aluminium Composite Roof Panel
Aluminium Composite Roof Panel
Aluminium Composite Roof Panel
Aluminium Composite Roof Panel
Aluminium Composite Roof Panel
Aluminium Composite Roof Panel
Roof Gable Profile2165mm
Roof Gable Profile1578mm
black side
black side
black side
black side
black side
black side
of 205www.stcny.com
No. Profile Qty Step
31 4 5
32 50 6
33 8 5
34 32 3
35 6 8
36 4 8
37 16 4
38 16 4
39 1
40 1
41 6 7
42 4 7
No. Profile Qty Step
19 2 7
20 2 6
21 1 5
22 1 5
23 2 5
24 4 6
25 4 6
26 2 6
27 20 2,5
28 120 2,3
29 16 1
30 8 5
We included some extra screws and bolts for your convenience.
Aluminium Composite Roof Panel
Roof Top Cover
Plastic Cap #1
Plastic Cap #2
U-shaped Connector
Roof Profile
Roof Profile
Roof Profile
Screw M6*8
Screw M6*18
Screw M6*25
Screw M6*38
Screw M6*45
Screw ø4*6
Nut M6
Plastic Cap #3
Ground Spike
Concrete Bolt
Spanner
Magnetic Hex Key
T- connector A
T- connector B
Roof Top Connector Beam
Aluminium Composite Roof Panel
black side
black side
5,6
of 206www.stcny.com
Assembling the Corner ProfilesPlace all the parts on a level surface.Make sure the pieces are in the correct positions before assembling.Carefully follow the order of assembly to ensure an easy installation.Wear proper safety gear including work shoes, gloves and goggles.
STEP 1
1 1 1 1
1 1
1 1
4
29 294
Components
Corner profile (1)
x 4Support plate (3)
x 4Roof connector (4)
x 4Support frame (2)
x 4Screw (29)
x 16
1.A Place corner profiles (1) parallel to each other the ground. Attach one roof connector (4) to each top end as shown and fasten with screws (29).
ATTENTION: The corner profile (1) has two screw holes to connect it to the roof connector (4) and 8 pre-drilled screw holes to attach rails (5,6,7,8) in step 3 at its top end.It has two screw holes to connect it to the support plate (3) at its bottom end.
Top end Bottom end
x 4
of 207www.stcny.com
1 1 1 1
1.B Slide support frames (2) over lower end of corner profiles (1).Attach support plates (3) to corner profiles as shown, using two screws (29) for each plate.
Leave support frames (2) about 10”over lower end of corner profiles (1) until step 4 (Securing the gazebo to the ground)
3
3
2
2 1
1
1
29
x 4
of 208www.stcny.com
5
7 77
5
5
6
8
8 8
6
9
6
27
27 28
2810
Inner Roof Connector (9)
x 6Outer Roof Connector (10)
x 10
2.A
2.B
Assembling the Rails
Insert connecting part of long rail (5) into blunt end of long rail (6) as shown. Attach with four screws (27). Repeat to create two sets of long rails.
STEP 2
Components
Long Rail (5)
x 2Long Rail (6)
x 2Short Rail (7)
x 2Short Rail (8)
x 2
Screw (28)
x 32
Screw (27)
x 16
NOTE: The Long Rail (5) and the Short Rail (7) have a preassembled connecting part to be inserted into Long Rail (6) and Short Rail (8).
Insert connecting part of short rail (7) into blunt end of short rail (8) as shown. Attach with four screws (27). Repeat to create two sets of short rails.
Attach inner roof connector (9) to short rail set as shown, using two screws (28). Repeat to create two sets.
Attach outer roof connector (10) to long rail set as shown, using two screws (28). Repeat to create two sets.
of 209www.stcny.com
28
28
10
10
10
Attach two outer roof connectors (10) to each long rail set at pre-drilled screw holes, using screws (28).
Attach two outer roof connectors (10) to each short rail set at pre-drilled screw holes, using screws (28).
Attach two inner roof connectors (9) to each long rail set at pre-drilled screw holes, using screws (28).
2.D
VIEW FROM THE TOP
ATTENTION: Attach roof connectors facing exactly in the directions shown.
VIEW FROM SIDE9
2.C
289
10 10 10
9 9 VIEW FROM THE TOP
x 2 x 2
of 2010www.stcny.com
28
28
2834
34
1
1
1
1
8
7
7
7
Attach one short roof profile set (7+8) to two cor-ner profiles (1) as shown, using screws (28) and supplied magnetic hex key (40) through holes in profile set.
3.A
3.B
Attaching the Rails to the Corner Profiles
STEP 3
Repeat step 3.A and 3.B to create two sets.
x 2
Components
Screw (28)
x 32Plastic Cap #3 (34)
x 32Magnetic Hex Key (40)
x 1
Close holes in profile set with plastic caps #3 (34).
of 2011www.stcny.com
7
7
8
8
6
6
5
5
6
1
1
1
1
IMPORTANT: After this step you should place the gazebo frame in its desired location.Make sure all corners are squared at 90 degrees.
1
Using at least 3 people, attach the two long roof profile sets (5+6) to corner profiles (1), connecting all four corner profiles (1).Fasten with four screws (28) and supplied magnetic hex key (40) on each side.Close holes in profile sets with plastic caps #3 (34).
3.C
28 34
of 2012www.stcny.com
Components
Fasten the gazebo frame to the ground, using four spikes (37) for each support plate.Lower support frames (2) to cover support plates (3).
Ground spike (37)
x 16
Securing the Gazebo to a Concrete Floor or Wood DeckOptionalComponents
Concrete bolts, washers and nuts (38)
x 16
Wood Bolts, washers x 16NOT SUPPLIED
to be purchased by user
Concrete Floor:1. Using a concrete drill, drill holes into the concrete floor, corresponding to the holes in support plates (3).2. Insert concrete bolts (38) into the holes and hammer into place, using a mallet.3. Fasten concrete bolts with washers and nuts.
Wood Deck:1. Using an electric wood drill, drill holes into the wood floor, corresponding to the holes in support plates (2).2. Insert wood screws with washers (not supplied) into the holes and fasten, using an electric screw driver.
4.A
NOTE: After securing the gazebo to the ground, we highly recommend filling the corner profiles (1) with 2 bags (20LBs each) of Pea Gravel each for extra stability,as shown.
1
11
1
1
3337
38
3838
21
Securing the Gazebo to the GroundSTEP 4
of 2013www.stcny.com
Roof Top Connector Beam (22)
x 1
Roof Top Cover (21)
x 1
Roof Gable Profile (11-1)2165mm
x 2
Roof Gable Profile (12-1)1578mm
x 4
Roof Gable Profile (12-2)1578mm
x 2
Roof Gable Profile (11-2)2165mm
x 2
Components
STEP 5
Using at least three people, install the roof gables (11-1, 11-2,12-1, 12-2) in the following order:
BOTTOM VIEW OF PROFILES
Installing the Roof Gables
22
11-1
11-1
12-212-2
11-212-1
12-1
12-1
12-111-2
1.
1.1.
1.
2. 2.
2.
2.
2.
2.
Nut M6 (33)
x 8U-shaped Connector (23)
x 2Screw (28)
x 36Screw (27)
x 4Screw (30)
x 8Screw (31)
x 4
Roof Gable Profile (11-1)
Upper end Lower end
Roof Gable Profile (12-1)
Roof Gable Profile (12-2)
Roof Gable Profile (11-2)
1578mm
2165mm
IMPORTANT: Make sure that the roof gable profiles (11-1, 11-2, 12-1, 12-2) are installed exactly as shown so that the pre-drilled screw holes will align properly with screw holes on the roof panels.
IMPORTANT: Each roof gable profile (11-1, 11-2, 12-1, 12-2) is composed of two parts, which are factory assembled and held together with screws. You will have to tighten these screws in Step 8,after assembling the roof.
T- connector A (41)
x 6T- connector B (42)
x 4
VIEW FROM BELOW(from inside gazebo)
of 2014www.stcny.com
ILLUSTRATION
12-1 / 12-2
5,6 / 7,8
Using screws (30) and nuts (33), connect roof gable profiles (11-1) and (11-2) to roof connectors (4) on top of corner profiles (1).
28
9
ILLUSTRATION
Install roof gable profiles (12-1) and (12-2). Using screws (28) connect profiles (12-1) to inner roof connectors (9) on long roof profile sets (5,6)and the other end to roof top connector beam (22).
Using screws (28) connect profiles (12-2) to inner roof connectors (9) on short roof profile sets (7,8)and the other end to roof top connector beam (22).
5.B
VIEWS FROM BELOW
VIEWS FROM BELOW
11-1
11-1
11-2
1
430
28
22
33Using screws (28), connect roof gable profiles (11-1 and (11-2) to roof top connector beam (22) as shown.
12-1
12-2
12-128
22
5.A
of 2015www.stcny.com
21
3131
28
28
41
41
41
21
4141
41
41
42
42
42
4212-1 / 12-2
42
2727
22
2323
5.C
5.D
Connect the roof top cover (21) to the roof top connector beam (22) as shown.First connect the two U-shaped connectors (23) to the roof top cover (21), using four screws (27).Then attach U-shaped connectors (23) to roof top connector beam ( 22) from below, using four screws (31).
Attach T-connectors A (41) to underside of roof gable profiles (12-1,12-2), using screws (28) as shown. Attach T-connectors B (42) to underside of roof gable profiles (11-1,11-2), using screws (28) as shown.
21
31
27
21
23
23
22
11-1 / 11-2
VIEWS FROM BELOW
VIEWS FROM BELOW
of 2016www.stcny.com
Aluminium Compos-ite Roof Panel (15)
x 2
Aluminium Compos-ite Roof Panel (16)
x 2
Aluminium Compos-ite Roof Panel (17)
x 2
Aluminium Composite Roof Panel (18)
x 2
Aluminium Composite Roof Panel (20)
x 2
Roof Profile(24)
x 4
Roof Profile(25)
x 4
Roof Profile(26)
x 2
Slide upper roof panels (15,16,17,18,20) into their positions through chanels in roof profiles (11-1,11-2,12-1,12-2) as shown. You may have to loosen the pre-installed screws in the roof profiles slightly to facilitate sliding of the roof panels.
6.A
Installing the Upper Roof PanelsSTEP 6
Components
Screw (28)
x 20Screw (32)
x 20
11-1
11-1
11-2
11-2
12-2
12-2
12-1
12-1
12-1
12-1
20
20
18
17
15
15
16
18
17
16
Remove protective plastic from both sides of upper roof panels (15,16,17,18,20). Place with black surface toward the sun facing out when installing.
IMPORTANT: Make sure that the roof panels are installed exactly as shown so that the pre-drilled screw holes will align correctly.
IMPORTANT: Each roof gable profile (24,25,26) is composed of two parts, which are factory assembled and held together with screws. You will have to tighten these screws in Step 8, after assembling the roof.
black side
black side
black side
black side
black side
of 2017www.stcny.com
12-1 / 12-2
11-1 / 11-2
42
41
2524
25 26
6.B
6.C
Using pre-drilled screw holes, fasten roof panels to roof gable profiles (12-1) and (12-2) with two screws (32) each from below.
Slide roof profiles (24,25,26) onto roof panels (15,16,17,18,20) fitting edges of panels into chanels of profiles as shown. You may have to loosen the pre-installed screws in the roof profiles slightly to facilitate fitting the roof panels.
VIEW FROM BELOW(from inside gazebo)
28
28
28
28
20
20
18
15
15
18
17
16
17
16
11-1
11-1
12-212-2
11-212-1
12-1
12-1
12-1
11-2
18
32
32
32
22
15
12-212-1
11-2
Attach roof gable profiles (24,25,26) to T-connectors A (41) and B (42) from inside the gazebo, using screws (28) as shown.
11-1
24 25
11-1
20
2624
24
24
25
25
25
26
18
18
15
15
16
1716
12-2
12-2
12-1
12-1
11-2
11-1
11-2
12-1
12-1
VIEW FROM BELOW
VIEWS FROM BELOW
of 2018www.stcny.com
19
14 13
32 32
10
32
12-1 / 12-2 11-1 / 11-2
13 / 14 / 19
Aluminium Composite Roof Panel (13)
x 4Aluminium Composite Roof Panel (14)
x 4
Installing the Lower Roof PanelsSTEP 7
Components
Remove protective plastic from both sides of lower roof panels (13,14,19). Place with black surface toward the sun facing out when installing.
Aluminium Composite Roof Panel (19)
x 2Screw (32)
x 30
Plastic Cap #1 (35)
x 6Plastic Cap #2 (36)
x 4
7.A
7.B
Slide roof panels (13,14,19) onto roof profiles (11-1,11-2,12-1,12-2) fitting edges of panels into chanels of profiles as shown, until their upper edge fits into the chanels in horizontal roof profiles (24,25,26).
Attach roof panels (13,14,19) to roof profiles (11-1,11-2,12-1,12-2) and outer roof connectors (10), using screws (32).
19
14
14
14
14
13
13
13
13
19
26
24
24
24
24
25
25
25
25
26
12-2
12-2
12-1
12-1
11-1
11-1
11-2
11-2
12-1
12-1
black side
black side
black side
of 2019www.stcny.com
41
4222
ENJOY YOUR COMPLETED GAZEBO !
Tightening the screws on roof profilesSTEP 8
7.C
8.A
Close off roof profiles (12-1,12-2) with plastic caps #1 (35) and roof profiles (11-1,11-2) with plastic caps #2 (36).
From inside the gazebo, tighten all pre-installed screws on profiles (11-1,11-2) and (12-1,12-2) to hold all roof panels firmly in place.
3536
11-1 / 11-2
12-1 / 12-2
VIEW FROM BELOW(from inside gazebo)
VIEWS FROM BELOW
Screws to be tightened
of 2020www.stcny.com
Systems Trading Corporation450 7th Avenue Suite 2809, New York, NY 10123Customer service: (877)782 4482 Email: [email protected]
EasyGrow8’x 12’ Greenhouse
Visit: http://www.stcny.comfor more Lawn and Garden products
Assembly Instructions
Gazebo GZ3 Santa MonicaAluminium Composite Roof Panels