Gammatec Catalogue 2014
Transcript of Gammatec Catalogue 2014
-
8/20/2019 Gammatec Catalogue 2014
1/140
Subsidiary of NTP
Product CatalogueIssue: November 2014
-
8/20/2019 Gammatec Catalogue 2014
2/140
GammaTec was established in 1981 and in 2009 became a subsidiary of the NTP Group ofCompanies. Initially the Company only marketed and sold its limited range of NDT Products inSouth Africa but, with the lifting of political sanctions on the country in 1994, GammaTec quicklyand successfully made use of the opportunities presented by the NDT Industry and the rest of theworld. Currently we actively export to over 70 countries worldwide. Our Head Office issituated in Vereeniging, South Africa. Our subsidiary offices in Dubai, Kuala Lumpur, Melbourne andBrussels provide a high profile “ground floor” presence in these regions, with key distributors appointedin various other countries.
The Vereeniging office services South Africa, the rest of Africa and surrounding Islands as well asthe Indian Ocean Rim. The Middle East, Baltic and Caspian are handled from the Dubai office. OurKL office handles South East Asia and the Far East. Lectromax (Australia) are manufacturers and globalsuppliers of Magnetic Particle Bench Units and sell GammaTec products within the Australasian region.
Oserix (Brussels) covers Europe, Canada, United States and Central and South American regions.
The GammaTec range of Non Destructive Testing Equipment, Accessories and Consumables thatare not only stocked, but in many cases manufactured by GammaTec, include the following:
• Acoustic Emission;• Automated Systems (Ultrasonic, Phased Array, Eddy Current, Magnetic Particle, Dye
Penetrant);• Coating & Surface Inspection;• Dye Penetrant Inspection;• Eddy Current Inspection;• Magnetic Particle Inspection;
• Phased Array Inspection;• Radiographic Inspection (Carestream Industrex Film , X-ray, Gammaray, Radioactive Sources);• Ultrasonic Inspection (Flaw Detectors, Thickness Gauges, Probes) and• Visual Inspection.
We are the authorised distributors for a number of global players including Carestream (CarestreamIndustrex Film and Digital CR Systems), Dakota (UT Thickness Gauges), ICM (X-ray), JME (PipelineCrawlers), NTP (Isotopes), Oserix (Gammaray Projectors and Sources), Phoenix (UT Scanners andTransducers), Physical Acoustics Limited (Acoustics), and Sonatest (UT and PA Equipment andAccessories). Each subsidiary has elctronic and mechanical maintenance departments with qualified andskilled technicians capable of repairing, maintaining and calibrating the wide range of products we sell.
The Groups highly trained National and International Sales and Administrative Staff allow Customerenquiries and purchases to be quickly and efficiently executed. Products such as Radioisotopes andsensitive Ultrasonic Flaw Detection equipment are handled with competent ease.
It's the intention of GammaTec NDT Supplies SOC Ltd to ensure a safe work environment for allparticipants involved in the business of NDT, while at the same time providing a suitable return oninvestment (ROI) for all stakeholders including the shareholders and staff community of the company.
We strive to be the best provider of NDT equipment and services in the industry. Everyone inGammaTec is responsible for fully satisfying our customers by meeting or exceeding their needsand expectations. Our goal is 100% customer satisfaction 100% of the time. The Turnkey One-Stop policythat Gammatec offers makes it an exciting and interesting organization to deal with and the Group's Mottoof “CLIENT IS KING” speaks for itself.
PM/GSA/SAL-002.01.011.001-REV-2
Company Profile
-
8/20/2019 Gammatec Catalogue 2014
3/140
Physical: Head Office Building, Vision 21 IndustrialPark, Steel Road, Peacehaven, Vereeniging, SouthAfricaPostal: P .O. Box 264786, Three Rivers, 1939, SouthAfrica
Tel: +27 16 423 7731Fax: +27 16 423 1743Email: [email protected]: [email protected]: www.gammatecsa.com
Gammatec Aseana NDTSupplies Sdn. Bhd.
Lot 36, Ground Floor, Jalan PJS 11/14, BandarSunway, 46150 Petaling Jaya, Selangor, Malaysia
Tel: +6 03 5635 9947Fax: +6 03 5635 9847Email: [email protected]: [email protected]: www.gammatecsa.com
Gammatec Middle East Gen.Trdg. LLC.
P. O. Box 112843, Dubai, United Arab Emirates
Tel: +971 4 341 3667Fax: +971 4 341 3668Email: [email protected] Email: [email protected] Web: www.gammatecsa.com
Gammatec Nigeria Ltd
No 3 Chief Okpara Close, Off Waks Avenue,Rumuibekwe New Estate Extension, Port Harcourt,River State, Republic of Nigeria
Tel / Fax: +234 8461 0895GSM: +234 8030 991 376Email: [email protected]: www.gammatecsa.com
Lectromax Australia Pty Ltd
13 F Brougham Street, Eltham, Victoria, 3095, Australia
Tel: +61 3 9431 1041Fax: +61 3 9431 2405Email: [email protected]: www.lectromax.com.au
Oserix SA2, Rue de I'Eglise, B – 7134 Leval – Trahegnies,Belgium
Tel: +32 71 258 636Fax: +32 485 805 957 Email: [email protected]: www.oserix.com
Gammatec NDT Supplies SOCLtd.
PM/GSA/SAL-002.01.011.001-REV-2
Contacts
-
8/20/2019 Gammatec Catalogue 2014
4/140
Agencies
PM/GSA/SAL-002.01.011.001-REV-2
-
8/20/2019 Gammatec Catalogue 2014
5/140
Contents
Inspection Method
ACOUSTIC EMISSION TESTING (AE)
LEAK DETECTION
TECHNOLOGY PACKAGES
GENERAL AE EQUIPMENT
LIQUID PENETRANT TESTING (PT)
ELECTOMAGNETIC TESTING (ET)
EDDY CURRENT
Tube Inspection
Tank F loor Inspection
Portable Eddy Current Inspection
MAGNETIC PARTICLE TESTING (MT)
Bench Units & CoilsElectromagnetic Equipment
Ultraviolet Equipment
RADIOGRAPHIC TESTING (RT)
GAMMA RADIOGRAPHY
Close Proximity Systems
Projector Accessories
Isotope Consumables
X-RAY RADIOGRAPHY
Portable X-Ray Generator
Power Box and Control Panels
Portable X-Ray Crawler Units
DIGITAL RA DIOGRAPHY
Digital Radiography (DR)
Computed Radiography (CR)
RADIATION S AFETY
DARKROOM
Radiographic Consumables
ULTRASONIC TESTING (UT)
PHASED ARRAY
PORTABLE FLAW DETECTORS
THICKNESS GAUGES
Ultrasonic Trancducers and Accessories
BOLT TENSION MONITORING ULTRASONIC TUBE INSPECTION
ULTRASONIC SCANNER
Ultrasonic Accessories
HARDNESS TESTING
EQUIPMENT
GENERAL ACCESSORIES
COATING INSPECTION
HOLIDAY AND PINHOLE DETECTORS
COATING THICKNESS GAUG ES
VISUAL INSPECTION
VISUAL EQUIPMEN T
INFRARED & THERMAL TESTING
LEAK TESTING (LT)
REPAIRS, SERVICE & CALIBRATION
Section
1
1.1
1.2
1.3
2
3
3.1
3.1.1
3.1.2
3.1.3
3.2
3.2.13.2.2
3.2.3
4
4.1
4.1.2
4.1.3
4.1.4
4.2
4.2.1
4.2.2
4.2.3
4.3
4.3.1
4.3.2
4.4
4.5
4.6
5
5.1
5.2
5.3
5.4
5.55.6
5.7
5.8
6
6.1
6.2
7
7.1
7.2
8
8.1
9
10
11
Equipment1 -14
1 - 6
7 - 10
11-14
16 - 33
16 - 20
16 - 18
19
20
21 - 33
21 - 2728 - 30
30 - 33
34 - 84
34 - 51
41 - 42
43 - 48
49 - 51
52 - 58
52 - 55
56 - 57
58
59 - 62
59
60 - 62
63 - 72
73 - 82
83 - 84
85 - 120
85 - 88
89 - 93
94 - 98
99 - 106
107108
109 - 120
121
122
122
123
124 - 126
124
125 -126
127 - 128
127 - 128
129
129
130
15
PM/GSA/SAL-002.01.011.001-REV-2
-
8/20/2019 Gammatec Catalogue 2014
6/140
Section 1: Acoustic Emission Testing (AE)
1.1 LEAK DETECTION
• Rugged construction• Analog read-out• Low or high temperature probe• Audio monitor (headphones)
Features
PM/GSA/SAL-002.01.011.001-REV-2
Model 5110 Hand-held, Single Channel Leak Monitor
The Model 5110 is a hand-held, battery operated acoustic leak detector. When the sensoris placed on a structural piping system, it will effectively detect leaks around flanges andthrough valves.
• Pressure vessel leakages• Storage tank testing• Heat exchanges• Valve closure leakages• Steam boiler tubes• Extrinsic leakages
ApplicationsApplications
1
-
8/20/2019 Gammatec Catalogue 2014
7/140
Valve- Squeak ™
Technology Breakthrough in leak Detection
SpecificationsFeatures
Designed for operations and maintenance personnel to perform frequent valve checks in theirunits, Valve-Squeak is an easy-to-use through-valve loss detection system. Small enough to fitin your pocket, Valve-Squeak isolates leaks of any size and in any valve saving you thousands,
if not millions .
• Size (LxWxH): 5.0” x 2.80” x 1.1”• Weight: 0.5 lbs.
• Power: 2–AA Alkaline Batteries 1.5V• Battery life: > 4 days continuous operation
• Processor: Internal microprocessor• Display: 16 LED's
• Operating temp: -22° - 158°F (-30° to 75°C)
• Stora ge tem p: -40°- 185°F (-40°to -85°C)
Locates leaks in valves including PSV, RV, CVand all othersUsed worldwide in refineries, chemical plants andoffshore platformsRealizes plant savings ranging from $500,000 to$5,000,000/year when combined with a VPAC/5131leak detection system (even leaks in a small valve canresult in significant losses)ROI is in the first useIdentifies losses rapidly
Eliminates excessive flaring
PM/GSA/SAL-002.01.011.001-REV-22
-
8/20/2019 Gammatec Catalogue 2014
8/140
VPAC™ II IS Intrinsically Safe Through- Valve Loss Control
MISTRAS Group has taken the VPAC™ throughvalve loss control instrument to the next level.The VPAC™II IS significantly simplifies assetmaintenance and increases operation safety.
Created for use in hazardous environmentssuch as oil, gas and petrochemical plants,power generating plants and offshoreplatforms, the VPAC™II IS is a dedicatedintrinsically safe acoustic leak instrument forthrough valve loss control. Using the sametechnology and sensors as our successfulVPAC™, the VPAC™II IS, for example, candetermine the loss of hydrocarbons to flare inhazardous areas and save millions of dollars
for the plants.
Starting with basic process informationand type of valve, along with the measuredAverage Signal Level (ASL) from theinstrument, VPAC™II IS uses a proprietary
algorithm to identify through-valve gas lossesand estimates leak rate.The user interface is simple and intuitive.The instrument is powered by a high capacityrechargeable battery lasting several weekswith typical use. The battery replacement onthis handheld power device is quick and easy,and the unit retains all settings even whenpowered off, so downtime is minimal.
Features
PM/GSA/SAL-002.01.011.001-REV-2
Specifications
• Large custom LCD backlit display• Dual frequency range selection• Accepts many types of sensors• Slide-in molded NiMh battery pack• Small, rugged, ergonomic package• Simple, intuitive user interface via a
large button keypad• Bluetooth data transfer
• Size: 4.75” x 1.4” x 7”• Weight:. 1 lb.• Power Source: Nickel Metal Hydride Battery• Pack• Battery Life: 100 Hours• LCD: Transflective LCD on Glass• Backlight: Blue LEDs with diffuser• Wireless Interface Type: Bluetooth Class B• Wireless Interface Range: 50ft• Operating Temperature: -15˚-158˚ F (-20˚-55˚ C)
• Storage Temperature: 40˚-185˚ F (-40˚ - 85˚C)
3
-
8/20/2019 Gammatec Catalogue 2014
9/140
SpecificationsFeatures
• Size (L x W x H): 150 mm x 65 mm x 35 mm• Weight: 0.35 kg• Power Consumption:
-
8/20/2019 Gammatec Catalogue 2014
10/140
32-Channel Micro-II AE System
Specifications
MISTRAS TRIPLE 5 AMS™ for HRSG
PM/GSA/SAL-002.01.011.001-REV-2
The MISTRAS | TRIPLE 5 AcousticMonitoring System is used for earlytube leak detection on pressurizedvessels such as pulverized coal orgas fired power boilers, recovery boil-
ers and feedwater heaters.
• Data logger and process interface hardware
• Amplifiers
• High Temperature Sensors
• High Temperature Cables
• Waveguides mount to cold side of the
boiler membrane• NEMA and protective sensor boxes
• Power Boiler AMS™ software
• Plant specific software and high signal
alarm outputs• 6 months of Weekly Surveillance, a remote
monitoring service• Installation, Maintenance & Operation Manuals
• Compact industrial chassis with hyper threading
high performance CPU, high capacity RAM, solid
state disk driver (SSD), USB ports, parametric
interface and AE activity LED installed.
• Works with either monitor/keyboard/mouse or
Ethernet connection to laptop/PC for remote
operation• Holds up to:
32 Channel for PCI-8
12 Channel for DiSP-4
8 Channel for PCI-2
• Optional DC power.
• Dimension: 110 x 220 x 450mm (W x H x D)
• Weight: 8 kg (4 boards installed)
5
-
8/20/2019 Gammatec Catalogue 2014
11/140
Features
Acoustic Ranger 5000
Hole and Blockage Detector
The Acoustic Ranger 5000 device detects holes, blockages, erosion and corrosion in tubes and pipes.The device emits a sound pulse which runs along the inside of the pipe, following it around bends and
even complex spirals. It can detect and locate holes, blockages and foreign bodies, along with areasof erosion and corrosion, in up to 600 metres of tubing, at inspection rates of up to 800 tubes an hour.The AR 5000 is the latest version of our acoustic ranging instruments and offers improved portability,integrated control and improved range and detection levels.Blockages caused by the process residue and corrosion product build-up and leaks caused by thematerial wall thickness reduction can occur in the most unexpected and inaccessible locations withoutwarning.
• Requires only one access point via existing flanges, fittings etc.•
Long-range – up to 600m from a single access point with a single trace• Fast application – immediate on-line results• Detection, location and sizing in a single shot• Portable and battery powered, requires only one operator• Unaffected by bends and is equally effective on straight or complex spiral tubing• Inspects any material and tube sizes from 6 to 500mm bore• High sensitivity – blockages and foreign bodies equivalent to 10% and holes of 1%
of the tube cross section are readily detectable in field use and higher sensitivitiesare achievable in controlled environments
PM/GSA/SAL-002.01.011.001-REV-26
-
8/20/2019 Gammatec Catalogue 2014
12/140
Features
Specifications
Portable Non-Intrusive Localized Corrosion Testing System
Pocket CORPAC™
PM/GSA/SAL-002.01.011.001-REV-2
The Pocket CORPAC™ combines an industry staple in non-intrusive corrosion testing with the portable
convenience made possible by the latest in Acoustic Emission (AE) technology. The Pocket CORPAC™
detects active localized corrosion in a variety of industrial structures and materials before costly and
dangerous effects can be seen or felt. Pocket CORPAC™ can tell customers when corrosion is active,what to do to decrease or stop it, and if those solutions are ultimately working. Pocket CORPAC™
detects a variety of localized corrosion mechanisms. Most importantly, it provides the only early-stagedetection capability of corrosion effects like micro-cracks, pitting and micro-delamination. Besides the
Pocket CORPAC™, no other traditional or advanced non-destructive testing options exist in the field to
identify such corrosion effects due to their limited size detectability. In fact without the Pocket CORPAC
™, detection of these defects could be done only through destructive testing. At less than a quarter the
size of its predecessor and with the latest turn-key software, the Pocket CORPAC™ provides anyone
with early localized corrosion detection capabilities – not just AE experts. Since Pocket CORPAC™ uses
proprietary algorithms that can differentiate corrosion signals from the background noise producedduring normal operation of plant equipment, there is no need for an AE expert to perform tests or take
assets offline.
One-of-a-kind early-detection capability, Pocket
CORPAC™ is the only nondestructive, on-line
method to detect corrosion phenomena in theirearliest stages. Less than a quarter of the size of
the original CORPAC™, Pocket CORPAC™ was
designed with portability and ease-of-use in mind.It builds on the original CORPAC™, which was
developed over six years in a partnershipbetween MISTRAS Group, SA (France), the
European chemical industry and a French univer-sity, all in conjunction with a European Union
Grant. We take full control of the acoustic signal
processing and automated corrosion type classifi-cation. The sleek, updated design can be used formany applications where portability is important.With a four-hour battery life and added ability to
operate the unit from battery belt or AC power.
• Dimensions: 9.5” H x 3.5” W x 1.4” D
(241 mm x 89 mm x 36 mm)
• Weight (with batteries): 2.5 lbs. (1.13 kg)
• Display: 3.52” Color LCD, QVGA portrait mode,
240 pixels W x 320 H transflective with
LED backlight
• Display Touchpad: Built-in touchpad on screen
for use with stylus andon-screen processing• Storage Memory: 28 Mbytes Flash for OS and data
storage• External Interfaces: Compact Flash port, USB 2.0
Port• Power Consumption: Approximately 4 Watts
• Power Requirements:
• External DC adapter 12V @ 1A or
• Internal 7.2V NiMH battery pack,
rechargeable in-situ or with optional Charger
• Battery Life: 4 hours intermittent use• Operating Temp: 23° to 115°F (-5° to 45°C)
• Storage Temp: -4° to 140° F (-20° to 60°C)
1.2 TECNOLOGY PACKAGES
7
-
8/20/2019 Gammatec Catalogue 2014
13/140
Specifications
• DiSP-24 Hardened, Portable Computer • PCI/DSP-4 Data Acquisition Boards with up to 8
parametric inputs• R15I-AST sSensors with integral 40dB preamp• Parametric Breakout Box and Parametric Sensors
• PowerPAC™ Software Package- PowerPAC Data Acquisition and Analysis Softwarewith 2-D & 3-D Location Software Modules
- AEwin Post Processing Analysis Software- Database Software with EPRI Cases- PDDMATE Post-processing software• Documentation- EPRI Reports Phases I, II & III- Technical papers- Case Studies• Three Day Classroom Training (theory) andStart-up Assistance
• 10 Days on the Job Training (Field Test)• Consulting Time (Remote and On-site)
DiSP-24 : 24 Channel, Digital AE instrument whichincludes PAC R15I integral preamp sensors with built-inself diagnostics capability (Auto Sensor Testing) and 30meter cables. The system comes with a built-in highperformance PC controller, RW-CD, keyboard, mouse and
video monitor and is shipped in a rugged transport case.This system can be used from the smallest of transformers(typically around 13.8 kV) to the largest GSU transformers(typically around 500 kV). Three current transducers(CT) and 2 resistance theorem devices (RTD) needed forrecording parametric signals are also included.PowerPAC™: This is real time AE data acquisition andfeature extraction software. It is used in real time testas well as post analysis to remove unwanted data due tosuch extraneous noise sources as pump operation, fanoperation, wind and rain. Along with this is the AE-WIN- POSTutility that is included with this package. Other utilities
include the TBFH software that is used to identify whether the AE source is due to either an electrical or thermal fault.This software also includes the 3-dimensional locationsoftware to provide real time test as well as post analysisfor three dimensional source location of faults detected ineither the main tank or the LTC compartment. PowerPAC™Database: A system created to facilitate the managementof data generated by testing power transformers with AcousticEmission. The main components are transformer nameplateand test data. A design number of some characteristics canbe assigned to a transformer. This allows comparison of
acoustic activity obtained in identical transformers.
Features
PowerPAC ™
Acoustic Emission Testing Technology Package
PowerPAC™ is an Acoustic Emission (AE) technology package for testing power transformers. Anon-line monitoring procedure was developed under an EPRI (Electric Power Research Institute)sponsored and tailored collaboration with Physical Acoustics Corp. (Project I.D. No. 051481). Thiscollaboration refined the package with three phases of program develoment resulting in on-line
monitoring of power transformers to detect, locate and assess electrical and thermal faults.AEsensors are installed on the transformer covering both the tank and the LTC compartment (if one ispresent) along with sensors to monitor pump current, fan current, load current, tank wall tempera-ture and LTC compartment wall temperature collecting data for comparison with the AE data duringpost test data analysis. In order to observe the effects of a complete load cycle, data is collectedover a period of 24 hours. Results are presented showing the location (in 3-D) and types of faults.A grading system is used for each fault and provides an overall evaluation of the transformer formaintenance or operation planning.
PM/GSA/SAL-002.01.011.001-REV-28
-
8/20/2019 Gammatec Catalogue 2014
14/140
Outdoor AE and Sensor Fusion System
Features
Designed to
Sensor Highway™ II
PM/GSA/SAL-002.01.011.001-REV-2
The Sensor Highway™ II (SHII) is an Acoustic Emission (AE) monitoring system with
up to 16 high-speed channels and 16 standard parametric input channels (expandable
to over 100). The system is designed for unattended and remote monitoring use in
structural health, process and condition monitoring applications. It is rated for outdoor
use and comes equipped in a rugged weatherproof NEMA 4 enclosure.
• Scalable for large channel deployment,
allowing for multiple units to be placedstrategically on asset being monitored
• Designed for outdoor environments with
a minimum power dissipation and atemperature range of (-35˚ to 70˚C)without the need for heaters or airconditioners
• Direct On-Board Terminal Block
connections and DIN rail mounts for external sensor inputs
• Various communication interfaces available
for data communication & remote control
including Ethernet, Wireless, Cellular Modem
and Satellite• Scalable system connecting additional units in
the field and time synchronization optionsbetween remote units
• RS-232/485, 4-20mA, Voltage inputs for
sensors
• Monitor effectiveness of repairs/
retrofits• Monitor pre-existing/known active
defects• Monitor “hidden areas” where visual
inspection is difficult or impossible• Monitor high stressed areas showing
flawlike activity• Wire break monitoring on suspension
cable and cable stay bridges
9
-
8/20/2019 Gammatec Catalogue 2014
15/140
Loose Parts Monitoring Equipment (LPME)
Features
PM/GSA/SAL-002.01.011.001-REV-2
LPME monitors, detects and evaluates metallic loose parts in reactor systems using transientacoustic signal analysis. Acoustic sensors/accelerometers are permanently located at strate-gic positions on the system being monitored (in direct contact with pipes and vessels), where
loose parts are most likely to impact. The sensors detect the impact of any loose parts as theycome in contact with the pipe or vessel wall. The sensors detect the mechanical vibration
propagating from the point of impact and convert it into an electrical signal that is amplified bythe system preamplifier, processed by the Loose Parts Monitor Equipment Data Acquisition
System (LPME-DAS) and recorded by the Data Acquisition Computer (DAC). The software
(LPME-DAQ) alerts the operator and control room when a loose part is detected, and
provides a user-friendly interface for the operator to analyze the transients, differentiatebetween noise and impact signals and determine location and impact characteristics.
• Digital design gives real time results
• Latest digital technology• Seismically tested to NRC standards
• Four discrete signal filters prevent false alarms• Multiple alarms and alarm levels settings• User-friendly Windows based software
• Accurate software location algorithms• Graphical displays of reactors, piping, heat exchangers, etc.
• Meets ASME Standard, NRC 1.133
• Full documentation for easy OEM integration• Nuclear test sensors and charge amps
10
-
8/20/2019 Gammatec Catalogue 2014
16/140
PM/GSA/SAL-002.01.011.001-REV-2
Specifications
Pocket AE-2™ Portable 2-Channel Acoustic Emission System
The Pocket AE-2 is a high performance,computerised, dual channel Acoustic Emission (AE)system packaged in a rugged, portable handheld unit. It offers all the performance features
of larger, more expensive AE systems, includingwide bandwidth, speed, AE features, samplingrates, waveform processing capabilities andaudible AE, all in a compact, battery-operatedpackage.The system is an excellent field survey tool,especially in situations where power is not readilyavailable. Equally useful in the laboratory,the system carries out lab tests by utilizing its2-channels of Acoustic Emission and 1 channel
parametric input for correlating load or stresswith AE activity.
In addition, linear location and spatial filtering arebuilt-in to provide more versatility.The Pocket AE-2 performs traditional AE featureextraction signal processing as well as advanced
waveform acquisition and processing. Resultsare displayed on an integrated color LCD touchscreen (240 x 320 pixels resolution for clearsharp graphics), able to display up to eightgraphs including waveforms, FFTs, histograms,line plots, point plots linear location, and eventdetection. AE data files are saved in DTA filesand can be transferred to your computer viacompact flash cards and/or USB, for full dataanalysis, using our optional AEwin™ software.
• All the standard performance features as in PAC’s PCI based multi-channel AEinstruments.• Hand-held portability for quick, efficient testing in the field or laboratory.• PDA type computer using Microsoft™ Windows-CE™ compact OS, familiar andeasy to use.• Utilizes PAC standard low cost passive AE low power sensors with an internal AEpreamp.
• Two AE channels with one high performance 18 bit A/D for each channel, allowingAE data processing at up to 10 MSPS.
• 16 bit A/D waveform capture and AE signal processing offers wide system dynamicrange without the need for gain controls.• 16 bit A/D parametric input to correlate AE to other process sensors.• Integrated rechargeable battery package lasting 4 hours (continuous) or more.Batteries are easily changed and can be charged outside of the system (withoptional charger).• Numerical keyboard with function keys for quick, easy setup and control.• Internal flash memory for storing setups and data files.• Permanent digital record of the test results in standard DTA, PAC data files,compatible with AEwin™ Software for detailed data analysis and data visualization.
• Compact Flash card and USB port for data transfer to laptop or desktop PC.
Size: 9.5" H x 3.5" W x 1.4" D(241 mm x 89 mm x 36 mm)Weight: 2.5 lbs. (1.13 kg) - with batteriesDisplay: 3.52” Color LCD, QVGA portrait mode, 240 pixels wide
x 320 high transflective with LED backlightDisplay Input: Built-in touchpad for use w ith stylus and on-screen
processingMemory: 128 MB Flash for OS and data storageExternal Ports: Compact Flash port, USB 2.0 PortPower Use: Approximately 4 Watts
Power: External DC adapter (12 V @ 1A) OR Internal 7.2V NiMHbattery pack, rechargeable in-situ or optional externalcharger
Battery Life: 4 – 6 hours intermittent use
Operating Temp: 23°to 115°F (-5°to 45°C)Storage Temp: -4°to 140°F ( -20°to 60°C)Connectors:AE 2 - SMB (Plug) connectorsParametric 1 - SMB (Receptacle) connectorAE Channel Description: Dual channel AE Input using SMB Connector inputs.
Low voltage (5 Volt). Phantom power is availablefor an external low voltage preamplifier or integralpreamplifier sensor
AE Freq. Response: 1.0 kHz to 1.0 MHz +/- 1.5 dBSoftware Selectable Filters: The Pocket AE system comes with multiple digitally
synthesized High and Low Pass filters in addition tosoftware-selectable High Pass analog filters, providingexceptional filtering characteristics for maximum noiserejection and optimal signal to noise ratio.
Digitizing: 18 bit, 20 MSPS ADCDigital Signal Processing: Real time FIR low pass filter. Each extracted feature
processed by a dedicated real-time pipelineprocessor
Features
1.3 GENERAL ACOUSTIC EMISSION EQUIPMENT
11
-
8/20/2019 Gammatec Catalogue 2014
17/140
USB Acoustic Emission (AE) Node
The USB AE Node is a single channel Acoustic Emission (AE) Digital Signal Processor with full AE hit
and time based features, including waveforms. Through the USB Connector, the AE Node is easily
interfaced to a Notebook or PC running Windows XP™ or Vista™ and Physical Acoustics Corporation
(PAC)’s well known AEwin™ or AEwin Lite™.
Up to 4 AE Nodes can be controlled by one Notebook or PC. The AE Node can accept single ended or
differential sensors amplified by an internal low noise preamplifier. Additionally, PK Series low powerintegral preamp sensors can be used for long distance connections.
Features Specifications
• Powered and operated through USB Port
• Rugged surface mount (SMT) construction
• High performance AE at a low cost• 1kHz to 1MHz bandwidth
• Selectable analog filters and programmable
digital filter• Waveform and Location Options
• AE Input: 1 Channel per USB node
(4 nodes per system)
• Frequency Response: 1.0 kHz to 1.0 MHzAE Digitizing: 18 bit, 20MSP ADCs
• Parametric Inputs: 1-4 CH , 0-4V, 16 bitsOS: Windows XP or Vista
Case Size: L 6” x W 3” x H 2”(152 x 76 x 50mm)
• Weight: 0.8 lbs. (0.36kg)• Power Requirements: USB Powered (5V)
< 100 mA when running
PM/GS A/SAL-002.01.011.001-REV-212
-
8/20/2019 Gammatec Catalogue 2014
18/140
Multi-channel Acoustic Emission System
.SAMOS™ 32
Features
Specifications
.SAMOS™ 48
.SAMOS™ 112
SAMOS™
PM/GSA/SAL-002.01.011.001-REV-2
The SAMOS™ 32 AE system is geared for laboratory or industrial use, holding up to 4 PCI-8 cards
for up to 32 AE channels of operation. Based on a heavy-duty industrial PC computer chassis, the
SAMOS™ 32 has added features for reliable day-to-day operation, including extra cooling, ventila-
tion and the latest powerful PC computer. The most economical, high performance AE systemavailable today, the SAMOS™ 32 is ideal for users with tight system budgets.
Retaining all the features of a full size AE system, including activity Hit LED’s on the front panel,
the system is also designed to utilize our digitally controlled, full-featured, high fidelity audio moni-tor (optional). It measures 17”W (43cm), 17”D (43cm) and 6”H (15.2cm), and weighs 26 lbs.
SAMOS™ 48 is a portable AE system, equipped with a handle for carrying and an integral key -board built within the hinged front protective cover. Weighing less than 38 pounds with all 48 chan -nels, the SAMOS™ 48 is 21” long x 14” wide x 7.6” tall. Inside this portable enclosure is a powerful
PC computer, large hard disk, floppy drive, R/W CD/DVD drive and the standard complement ofparallel printer port, serial port, USB and mouse port. Built-in AE features include a digitally con -trolled audio monitor, up to 8 parametrics and AE Hit indicator LED’s. Expansion and communica-tion options include Ethernet LAN option and optional modem for remote control and communica-tions purposes. Both Internet and Intranet software and interfaces are available.
SAMOS™ 112 is a large capacity 112-channel system and represents the industry’s largest number
of AE channels in a single enclosure. The system comes equipped with an advanced PC based
CPU and all standard peripherals including a LAN connection. Multiple cooling systems make
SAMOS™ 112 a rugged multi-channel system especially for demanding applications in harsh
environments.
• Compact 32 or 48 or 112 channels
of simultaneous DSP based AE
waveforms and features in real time• Operate under advanced AEwinTM
Windows software• Individual 16-bit A/D's on each
channel• PCI Bus for high speeed processing
• LAN interface included with optional
network and Internet monitoringcapabilities available
• 400 kHz bandwidth
• Low power consumption, runs cool• Acousto/Ultrasonic systems applica
tions• ISO-9001 certified and CE marked
with low noise• LED AE activity and “Super Audio
• Front Panel activity lights providestatus on AE data as well as to giveyou a system diagnostic
• All digital, full-featured Audio Monitor
built in and ready for “high fidelity”listening (optional).
• Auto Sensor testing (AST) standard
with all PAC systems for easy system/
sensor self calibration and interfacecoupling efficiency.
• Software available for the SAMOSTM
includes the state-of the-art PACwinTM
Software with 25 years of AcousticEmission application experience behind
it, this Suite is comprised of three indi-vidual software packages (purchasedseparately).
13
-
8/20/2019 Gammatec Catalogue 2014
19/140
Comprehensive, Versatile & Friendly AE Software
AEwin™
PM/GSA/SAL-002.01.011.001-REV-2
AEwin™ is a 32-bit MS Windows™ compatible (XP/Vista/Windows7) software for real-time “simulta-neous” Acoustic Emission (AE) feature and waveform processing, display, fast storage and replay.
Used for true, real-time operation and control with your MISTRAS AE Systems (DiSP, PCI2,
SAMOS, SH II, AE USB Node, Wireless AE Node). The software has full MS Windows™ resourcesincluding use of any screen size, printing JPGExport, networking, multi-tasking, and multi-process-ing. AEwin™ also features complete compatibility with MISTRAS’ standard data file format (DTA),
allowing you to replay and analyze your previously collected AE files and framework for easilyadding graphs and additional graph screens and user controllable tool bars including setup icons,acquisition control, line listing, status and statistics.
14
-
8/20/2019 Gammatec Catalogue 2014
20/140
2.1 ACCESSORIES
Test Blocks
Product Code DescriptionNCB0059 Aluminium Penetrant Sensitivity Test BlockNCB0060 Sherwin PSM-5 Penetrant System Monitor Panel (Polished or Grit)
2.2 CONSUMABLES
ARDROX Consumables
PM/GSA/SAL-002.01.011.001-REV-2
Product CodeCleanerNCC0031NCC0053NCC0054DeveloperNCD0015NCD0016
PenetrantNCP0027NCP0019NCP0032NCP0020NCP0033NCP0034NCP0051
Description
10 x 400mlArdrox 531910 x 400ml Ardrox HF-R / 9RP5 Halogen Free4 x 5 litres Ardrox HF-R / 9RP5 Halogen Free
10 x 400ml Ardrox HF-D / 9D1B Halogen Free4 x 5 litres Ardrox HF-D / 9D1B Halogen Free
10 x 400ml Ardrox 907PB Red Water Washable4 x 5 litres Ardrox 907P Red Water Washable10 x 400ml Ardrox 970P24 Water Washable Fluorescent1 x 25 litre Drum Ardrox 970P24 Water Washable Fluorescent10 x 400ml Ardrox HF-P / 996PB Halogen Free4 x 5 litres Ardrox HF-P / 996PB Halogen Free1 x 25 litre Drum Ardrox 985P13 Post Emulsifiable Fluorescent
15
-
8/20/2019 Gammatec Catalogue 2014
21/140
ApplicationsFeatures
3.1 EDDY CURRENT 3.1.1 Tube Inspection
TX-4400 Eddy Current (Tube Inspection) System
The TesTex, Inc TX-4400 ECT Inspection System is based on the Eddy CurrentTechnique to quickly and accurately inspect non-ferrous metal tubing from the I.D. Byusing four-frequencies in a simultaneous injection mode, defects such as ID/OD pitting,baffle cutting, erosion, steam impingement, general wall thinning, etc. can be detected andsized. The system also has differential and absolute responses for each frequency, a built
in reference signal to generate an absolute signal without the use of a reference probe,and real-time mixing for suppression of support/baffle plates. The TX-4400 system usesboth DSP and FPGA technologies to enhance performance capabilities while maintaininglow cost and size. Utilizing easily configured and readily available USB technology, the TX-4400 interfaces to any windows based PC/notebook. All data is archived for analysis andprocessing as well as for future inspections and trending.
Section 3: Electromagnetic Testing (ET)
• Four frequency simultaneous injection• Up to 5 ft/sec. tube inspection rate• PC based software for acquisition/analysis• Dynamic/user selected gain• Real time mixing• USB interface• 1 KHz to 1.2 MHz• User selectable driver output level, 0-9v p-p• Compatibility with bobbin, surface, and magnetic
saturation (permanent or dc) probes• Wide variety of specialized data filters• Automated analysis software (TX-SOLUTION )*
• Automated report writing software (AR WIZARD )*• Probe pusher puller (PDP 22 )*• Probe pusher (PD 6k )*• Tube sheet mapping (TX-MAP )
• Condensers• Feed Water Heaters• Coolers• Evaporators• Chillers
PM/GSA/SAL-002.01.011.001-REV-2 16
-
8/20/2019 Gammatec Catalogue 2014
22/140
Features
PM/GSA/SAL-002.01.011.001-REV-2
• Real Time 3-D Color Graphic Displays for Data Acquisition and Data Analysis/Display• Inspects Straight Sections and Bends; U-Bends can be inspected with special probes• 300-400 tubes average productivity of one system in a 10 – 12 hour shift• Inspects through scale on the ID or OD• Probe Fill Factor not critical to operations• Numerous Signal Processing Algorithms available for Data Analysis• Windows Based Software• Small, Lightweight, Modular, PC Based Design• 110/220V Operation• Pr obe sizes range from 8.1 mm (0.320 inches) to 152mm (6 inches)• Low Signal to Noise Ratio• Probe lengths of up to 150 feet without signal pre-amplification• System Frequency Range of 5Hz to 30KHz. (lower frequencies are critical for the
inspection of thicker walled Carbon Steel tubing and Air Cooler – Fin/Fans)
Eagle 2000 RFET System
The Eagle 2000 uses RFET probes that have eight (8) sensors equally spaced around theprobe's circumference (smaller diameters may have four or six sensors).
17
-
8/20/2019 Gammatec Catalogue 2014
23/140
• 1 GHz Processor • 1 GB ram• 16 GB compact flash• Microsoft Windows XP Professional SP3• USB 2.0• Industrial 3 button mouse• 5.6 LCD display with VGA controller • AC or DC opera• 1 GHz Processor
• 8 channels (8 phase, 8 amplitude)• Frequency selection from 5 to 80 Hz• PC based• LFET method (low frequency electromagnetic
technique)• USB interface• Powered from computer USB port• Environmentally sealed connections• Compatible with any TesTex LFET based
scanners• Lightweight and compact
Prodigy 8C boiler tube/pipe scanning system
The Prodigy 8C is a one man, multichannel NDT system for scanning most any boiler tube/pipe from the O.D. It detects and quantifies I.D., O.D., and internal material defects inferrous materials. The system uses a dry non-contact method based on the principles of
Electromagnetism (LFET). It is forgiving to uniform surface scale and tests at a scanningspeed of 10 to 15 ft. (3 to 4.5m) per minute. The system is fast, accurate, cost effective,and field proven. This system has its own built-in computer which can be conveniently attachedto the operator's body. This system can be adapted to many different applications includingtesting ligaments, bends, space constricted areas, and small diameter tubing.
Features
Specifications
PM/GSA/SAL-002.01.011.001-REV-2 18
-
8/20/2019 Gammatec Catalogue 2014
24/140
SpecificationsFeatures
TesTex – Falcon 2000 Mark II (LFET tank floor scanner)
The world's most advanced and compact inspection tool for above ground storage tankshas many new features to enhance inspection capabilities. These improvements are basedon TesTex's field experience in testing hundreds of storage tanks, and input from dozensof NDT inspectors from both domestic and international industries. The Falcon 2000 Mark
II System is based on the principles of Low Frequency Electromagnetic Technique (LFET).
• PC based / Modular electronics using digitalsignal processing
• Uses a maximum voltage of ± 12V DC insideof tank, meeting required specifications for tank safety
• 32 channels – Falcon Sr.; 16 channels –Falcon Jr.
• Uses scanners that have 16 or 64 pick upsensors equally spaced to scan flat surfacescovering 102 mm (4 inch) or 330mm (13 inch)swaths per pass
• Reporting software generates a tube sheetmap for LFET tube inspections and a tank
• Does not use permanent magnets so lightweight(under 30 lbs)
• Requires minimal floor preparation, no cleaning or sandblasting of surface and tests through coatings
• Determines top surface flaws from bottom surfaceflaws
• Continues to show flaw responses even after theunit has stopped moving
• Maximum penetration up to 32 mm (1.25 inch)• Scanning speed of 4.5 - 6m (15 – 20 feet) per
minute• Tests ferrous materials such as carbon steel and
cast iron• Upgradable to test non-ferrous materials such as
stainless steel and aluminium• Real time data display with advanced signal
processing• Wheel assemblies provide easy manoeuvrability
and independent height adjustment
• Full coverage over scanned area with no 'deadspace'
3.1.2 Tank Floor Inspection
PM/GSA/SAL-002.01.011.001-REV-2 19
-
8/20/2019 Gammatec Catalogue 2014
25/140
PM/GSA/SAL-002.01.011.001-REV-2
Eddy Current Flaw Detector VD3-71
The VD3-71 Eddy Current Flaw Detector is intended for manual testing with eddy currenttechnique for surface and subsurface defects, such as material discontinuity (cracks, laps,cissings, fine cracks etc.), in products made from ferromagnetic materials.
It is applied in the following branches of industry: aircraft, railway transport, oil and gas, chemical,power and engineering.
• Possibility of defects detection:• Depth = from 0.1 mm• Opening = from 0.002 mm• Operating frequency: setup range
from 50 Hz to 12 MHz• Generator output voltage (double
amplitude): from 0.5 V to 6 V• Adjusted gain range: 30 dB• Adjusted preamplifier range: 40 dB
• Phase signal variation (signal rotationrange from 0° to 360° with a step0.1°, 1°, 10°)
• Samples frequency up to: 6 kHz• Digital filtering, 5 filter types:
• Lowpass• Highpass• Bandpass• Differential• Averaging
• Storage of a great number of setupsand testing results in the flaw detector memory
• Advanced capabilities of data analysis dueto the speciality application-dependent software
• Mode of two-way communication with PC USB• Estimate of defect depth and length, and also
LED and sound alarm of the detected flaw• High ergonomics – convenient and small
case, small weight, high-contrast TFT display,assignment of the most frequently used functionsto 'hot keys' of the keyboard, and also the usageof a special leather cover for handy and secureholding of the instrument
• Large colour high contrast TFT display• Alarm system: 4 three colour LEDs, sound alarm• Possibility of operation in two frequency mode• Possibility of encoder and rotary scanner connection• Possibility of low temperature instrument
implementation
SpecificationsFeatures
3.1.3 Portable Eddy Current Inspection
20
-
8/20/2019 Gammatec Catalogue 2014
26/140
Specifications (cont'd)
Specifications
The MAGMASTER 5000 is a high quality, large capacity, magnetic particle crack detector,designed to provide the performance necessary to meet the exacting demands for qualitycontrol during production and maintenance in the automotive, railroad, marine and generalengineering industries. The MAGMASTER 5000 is designed to accept crankshaftsup to 2750mm long and 1000kg weight as used in heavy off road and stationary engines,as well as many types of locomotive and marine crankshafts and components. TheMAGMASTER 5000 complies with ASTM-E1444-05, BS6072, AS1171 and ElectricalSafety Standard AS3100. In addition it meets major engine manufacturers' specificationsfor crack testing by the magnetic particle method e.g. Caterpillar, Cummins, etc. A widerange of optional facilities is available to extend the versatility of operation, including offbench testing of parts too large to be accommodated on the machine, e.g. engine blocks,
marine propeller shafts, etc.
• Electronic timer controls the period of themagnetizing shots for consistent repeatability.
• Automatic push button electronic ACdemagnetizing.
• Electronic solid state switching for HEAD/COIL, AC/DC mode selection.
• Cable takeoff points for special or off benchtesting,e.g. engine blocks.
• Pneumatic end clamp system fitted to bothheads for positive electrical contact.
• Easy running tailstock for fast traversing andfitted with pneumatic lock.
• Supplied with adjustable roller steadies tosupport cylindrical parts from 50 to 200mmdiameter and up to 1000kg.
• 20 litre inspection fluid storage system withefficient jet agitation system suitable for oil or water based fluids.
• The demag cycle is continuously monitoredby a flashing digit and when the cycle iscomplete, the digit reverts to a steady state.
• Two axis magnetising. Current throughpart to check for longitudinal or lengthwisecracks, and coil magnetizing to check for radial or transverse cracks.
• 5000 AC + 5000 half wave DC peakmagnetizing currents. AC to locate
surface defects and DC to locatesubsurface defects.
• Accepts parts up to 2750mm long and1000kg in weight. 450mm internaldiameter 4 turn coil, producing 12,000peak ampere turns. Optional 550mm coil.
• Optional coil transverse system wherebythe coil can be moved up to 120mm,lateral to the centre line, for increasedmagnetizing influence on small diameter parts.
• Digital ammeter accurately indicates peak
AC + HWDC magnetising currents. Holdscurrent reading on display for 5 secondsand automatically resets.
3.2 MAGNETIC PARTICLE TESTING (MT)
3.2.1 Bench Units and Coils
MAGMASTER 5000 Heavy Duty Crack Detector
PM/GSA/SAL-002.01.011.001-REV-2 21
-
8/20/2019 Gammatec Catalogue 2014
27/140
Specifications (cont'd)Specifications
MAGMASTER 4500 General Purpose Crack Detector
The MAGMASTER 4500 is a versatile high quality magnetic particle crack detectordesigned to meet the demands for critical inspection of parts during overhaul in the aircraft,automotive, and general engineering Industries. Pneumatic clamping heads enables a widevariety of ferrous parts to be tested, including crankshafts, camshafts, cylinder heads,
axles, gears, con rods, bolts, pins, and nuts etc. A range of optional equipment is availableto extend the versatility and convenience of operation, including off bench testing of partstoo large to be accommodated on the machine. The MAGMASTER 4500 complies withInternational Standards for Magnetic Particle Inspection including ASTM E1444-05, AS1171-1998, BS6072, and Electrical Safety Standard AS3100.
• Australian manufacture backed by over 30years of experience in magnetic particleinspection systems.
• High quality and ruggedly constructed.Stainless steel tank with integrated 20 litrefluid storage sump and pump agitationsystem.
• Reliable plug in electronic control system.• 2 year warranty on electronic modules.• 5 year warranty on the magnetizing
transformer.• Digital ammeter and controls at eye level.• Ammeter holds display for approx. 4
seconds for ease of verification.• Thermal overload protection. Overload
condition indicated on the display screen.• The rotary position of the current control is
displayed digitally in unit steps 1-100enabling precise setting of any desiredmagnetizing current value up to the ratedmaximum.
• Operator efficiency and work throughputenhanced by ease of operation.
• Two axis magnetising.Current through partto locate longitudinal or lengthwise cracks,and coil magnetising to locate radial or transverse cracks.
• Quick changeover from contact heads tocoil. The selected mode is indicated on thecontrol display screen.
• 4500amps AC peak magnetising current.Optional HWDC in addition to AC.
Automatic push button AC electronic
demagnetizing• The demag cycle is continuously monitoredby a flashing digit and when the cycle iscomplete, the digit reverts to a steady state.
• Accepts parts up to 1350mm long and100Kgs in weight on head shelves, and250Kgs when supported on steadies.
• Optional 2000mm capacity. Optional heavyduty heads to support up to 500Kgs onsteadies 350mm internal diameter coil,producing up to 12,000 peak ampere turns.Optional 450mm coil.
PM/GSA/SAL-002.01.011.001-REV-2 22
-
8/20/2019 Gammatec Catalogue 2014
28/140
MAGMASTER 3000 Automotive Crack Detector
The MAGMASTER 3000 is specially designed as a low cost high performance crackdetector, for automotive engine reconditioning. All petrol engine and small dieselcrankshafts, camshafts, heads, axles etc. can be quickly and thoroughly checked. TheMAGMASTER 3000 is ideal for the smaller workshop requiring a quality crack detector
with the minimum of capital outlay. In addition, the MAGMASTER 3000 has manyapplications in general industry requiring a low cost effective crack detector. The unit isextremely easy to use and requires no special skills to obtain excellent results. Uniqueswivel mounted magnetising coil allows rotation 45° in either direction, total 90° rotation,to detect cracks running in any direction, lengthwise or radial.
• High quality construction for long servicelife Stainless steel tank.
• Australian manufacture backed by over 30years experience in magnetic particleinspection equipment.
• Reliable electronic control system, with twoyear warranty.
• Unique swivel mounted coil eliminates
necessity of additional magnetising processof passing current through part.
• Plug in electronic module for quickchangeover and minimum downtime.
• All electrical controls to IP56 rating.• Operator efficiency and work throughout
enhanced by ease of operation.
• Accepts parts up to 1370mm (54 inch) long,weighing up to 100kgs (225lbs.). Longer parts can be tested in sections.
• High intensity magnetising coil producesup to 10,000 AC peak ampere turns.Magnetising coil is sealed and insulated inan impact resistant oil proof enclosure.
• 350mm (14") I.D. traversing coil can beparked at left, clear of supports, to alloweasy loading of part from the front or overhead.
• Simplified electronic control provides aselection of high or low magnetisingintensities to suit any application.
• Magnetising shots are electronically timed,for consistent results.
• Automatic push button AC demagnetisingfacility.
Specifications (cont'd)Specifications
PM/GSA/SAL-002.01.011.001-REV-2 23
-
8/20/2019 Gammatec Catalogue 2014
29/140
Specifications (cont'd)Specifications
MAGMASTER 2000 Small Parts Crack Detector
The MAGMASTER 2000 is an economically priced, compact unit, ideal for volumeproduction or batch testing of a wide variety of ferrous components for fatigue orprocessing defects by the magnetic particle method. Nuts, bolts, pins, shafts, con rods,gears, camshafts etc. can be quickly and thoroughly tested.
It complies with International standards for magnetic particle inspection - ASTM E1444-05, AS1171, BS6072 and Electrical Safety Standard AS3100. A range of optional accessoriesis available to extend the versatility of the machine's operation, including HWDCmagnetising current for the detection of subsurface defects.
• The left-hand head is fitted with an air operated contact face initiated by a headmounted hand switch and provides a highpressure end clamping action for positiveelectrical contact.
• An air regulator and gauge are fitted tocontrol the clamping pressure.
• A foot switch allows hands free operation• Head contact faces fitted with resilient
multilayer copper gauze pads.• Vee blocks supplied to support and
facilitate rotation of cylindrical parts.
• Can be easily removed to provide a largeunobstructed contact face.
• Integrated 20 litre inspection fluid storagesystem with efficient particle agitation andrecirculation system, suitable for oil or water based inspection fluids, c/wfluid applicator.
• Supplied with 20 litres high qualityfluorescent inspection fluid.
• Operates from a nominal 240V 50Hzsingle phase supply. Maximumdemand is 18 amps.
• Two axis magnetising. Current through partto check for longitudinal or lengthwisecracks, and coil magnetising to check for radial or transverse cracks.
• 2000 amp AC peak magnetising current.Optional halfwave DC current. Acceptsparts up to 1100mm long and 30kg in weight.
• 250mm internal diameter traversing coil,producing up to 5000 peak ampere turns.
• Continuously variable current control
enabling setting of any required magnetisingcurrent value up to the rated maximum.• Automatic press button electronic AC
demagnetising.• Electronic timer automatically controls the
period of the magnetising current.• Digital Ammeter accurately indicates the
magnetising current.• Holds reading on display for 4 seconds and
auto resets.
PM/GSA/SAL-002.01.011.001-REV-2 24
-
8/20/2019 Gammatec Catalogue 2014
30/140
Features
LECTROMAX 5000 Magnetic Particle Inspection System
The LECTROMAX 5000 is an extremely versatile, high quality magnetic particle crackdetection system, offering excellent performance and reliability. It is designed specifically to meet the exacting demands for quality control during production and maintenance in theaerospace and aeronautical industries. In addition to conforming to the general standardsfor the testing of critical components with magnetising peak currents up to 5000 amps
peak AC, plus halfwave DC, the LECTROMAX 5000 complies with MIL-M-6867C, ASTME1444-05, BS6072, AS1171, and Australian Electrical Safety Standard AS3100.
• Highly reliable electronic system, with plug in modules and supported by a 2 year warranty
• Advanced & accurate dual digital ammeter system with a programmed microprocessor for accuracy and tracking. The required current can be preselected and displayed onone ammeter, and when a magnetising shot is initiated, the actual current is displayed
on the second ammeter and held on display for approx. 5 seconds for ease of verification.• Magnetising shots are verified by an Illuminated indicator.• In addition to decaying AC demagnetisation, special circuitry enables the most difficult
part to be demagnetised by residual field cancellation.• High quality and rugged construction with stainless steel catchment tank and fluid
reservoir.• A comprehensive range of options and accessories are available to extend the versatility of the system to suit virtually any testing requirement, including capacities to
accept parts up to 3000mm long and 500kg in weight, and 6000 amp and 7000 amppower pack upgrades.
PM/GSA/SAL-002.01.011.001-REV-2 25
-
8/20/2019 Gammatec Catalogue 2014
31/140
Features
LECTROMAX 100 Series Demagnetisers
LECTROMAX 100 Series of demagnetisers include a range of standard demagnetisers invarious sizes, voltages and intensities. A range of standard optional accessories isavailable. In addition, special purpose demagnetisers can be manufactured to suitparticular applications, including high intensity air cooled types for continuous orintermittent duty. Continuous duty demagnetisers can be supplied for integrating with
conveyor systems. Intermittent duty demagnetisers are fitted with a 60 second timer, whichautomatically controls the energised period. The timer incorporates a panel mounted digitaldisplay, which indicates the elapsed time. All LECTROMAX demagnetisers areconservatively designed for maximum operating efficiency and long life.
PM/GSA/SAL-002.01.011.001-REV-2 26
-
8/20/2019 Gammatec Catalogue 2014
32/140
Features
LECTROMAX 150 Series Coil Magnetiser - Demagnetiser
The LECTROMAX 150 Series of portable coil magnetiser-demagnetisers is available in 3throat sizes, 250mm, 300mm, and 350mm internal diameter. Typical application is for thedetection of radial or circumferential surface or near surface defects in general engineering
ferrous components, including pipes, axles and transverse defects in fork lift tines etc.
• Part No. 150-25-FB Part No. 150 - 30-FB Part No. 150 - 35-FB• Inside diameter: 250mm 300mm 350mm• Outside diameter: 350mm 400mm 450mm• Width: 110mm 110mm 110mm• Weight (approx.): 15kg 19kg 25kg
• Peak ampere turns 6000 5000 5000• Duty Cycle (1 min on, 1 min off) 50% 50% 50%
• Other sizes available to special order.
PM/GSA/SAL-002.01.011.001-REV-2 27
-
8/20/2019 Gammatec Catalogue 2014
33/140
3.2.2 Electromagnetic Equipment
Yokes
The Gammatec Electromagnetic yoke features dual coils, which provide maximum lifting
power without uncomfortable heating. The acid-proof, impact resistant body ensures
ruggedness and has been designed with operator comfort in mind making it easy to holdand operate.
Product Code DescriptionNCY0004 110V - Gammatec MK II Articulating LegsNCY0005 220V - Gammatec MK I Fixed LegsNCY0006 220V - Gammatec MK II Articulating LegsNCY0007 110V - Gammatec MK I Fixed LegsNCY0009 250V - Gammatec MK II Articulating Legs
The new MY-2 is the smallest, lightest hand-held yoke on the market –encapsulation in a rugged rubber housing makes it the most durable too.The MY-2 electromagnetic yoke is a rugged, high performance instrumentfeaturing a powerful AC magnetising field.
Product Code DescriptionNCY0002 220V – Gammatec MY-2 Articulating LegsNCY0011 110V - Gammatec MY-2 Articulating LegsNCY0012 240V - Gammatec MY-2 Articulating LegsNCY0010 42V - Gammatec MK II Articulating Legs
Yoke Accessories
Product Code DescriptionNCC0012 Electromagnetic Yoke 12V AC / DC ConverterNCT0249 Electromagnetic Yoke 42V AC TransformerNCI0216 Portable battery powered inverter 12V DC –
220V / AC for MY-2 Yoke
NCA0014 Rubber Magnetic Particle Powder ApplicatorNCB0022 Polyethylene Spray Bottle
The Gammatec Portapack is a portable battery operated DC power supply for use with allAC electromagnetic yokes. Charged batteries in special pouches are carried on a beltworn around the technician's waist. The yoke is plugged into the battery pack allowing thetechnician to conduct MPI in hazardous areas or where no power supply exists.
Product Code DescriptionNCP0018 Portable battery operated DC supplyNCC0114 Portapack Charger
PM/GSA/SAL-002.01.011.001-REV-2
Portapack
28
-
8/20/2019 Gammatec Catalogue 2014
34/140
PM/GSA/SAL-002.01.011.001-REV-2
Cases Product Code DescriptionNCC0013 Carry Case for PM2000 Permanent Magnet Yoke
NCC0038 Carry Case for Gammatec MK I, MK II and MY-2Electromagnetic Yokes
Permanent Magnet Yokes
The Gammatec permanent magnet yokes are light weight, ergonomically designed andvery powerful.
Product Code DescriptionNCY0008 Gammatec PM2000 Articulating Leg Permanent
Magnet Yoke
NCY0003 Gammatec PM2004 Permanent Magnet Yokewith Cable
Spare Parts Product Code Description NCK0010 PM2000/PM2004 Permanent Magnet Keeper c/w spare Magnets
and Feet
NCC0167 MY-2 Yoke Power CableNCE0008 MY-2 Yoke Articulating Leg Extension PieceSF0051 MY-2 Articulating Foot Piece
Centrifuge Stand and TubeProduct code DescriptionNCS0027 Gammatec MPI Centrifuge StandNCT0028 Magnetic Particle Centrifuge - ASTM 100ml, pear shaped
Indicators & Calibration BlocksProduct Code Description
NCI0002 Castrol Magnetic Flux Type I (Brass)NCI0003 Castrol Magnetic Flux Type II (Silver)NCI0014 ASME Magnetic Particle Field Indicator (Pie Gauge)NCI0016 Berthold Spoon Magnetic Field IndicatorNCB0033 MTU No. 1 MPI Test BlockNCB0061 Ketos Ring Steel Test Block
Gaussmeters Product Code Description NCM0003 Gaussmeter including Probe
NCM0045 Gaussmeter CYHT201including Transverse Probe CYPT-T15A
NCP0142 Probe for use with GaussmeterNCI0019 Magnetometer Mod 25 Residual Field Indicator
29
-
8/20/2019 Gammatec Catalogue 2014
35/140
Yoke Test Weights
Product Code DescriptionNCW0023 18kg MPI Test Weight (with carry case)
NCW0024 4.5kg MPI Test Weight (with carry case)
Consumables
3.2.3 Ultraviolet Equipment
Ultraviolet Lights
Product Code Description NCL0005 Gammatec UV 100 Ultraviolet Light (220V)NCL0015 Gammatec UV 100 Ultraviolet Light (110V)NCL0020 High Flux Ultraviolet LED Torch Kit
Including:365nm LED Torch2 x 3.7V re-chargeable batteries1 x battery chargerCarry Case
Gammatec’s Ultravoilet Light is a rugged, high intensity, low cost black light used for thedetection of low-level fluorecence in Non Destructive Testing Techniques.
PM/GSA/SAL-002.01.011.001-REV-2
Product Code
Background
NCB0012
NCB0013
NCB0054
NCI0010
NCI0011
NCI0018
NCI0012
NCI0013
Powder
NCP0023
Description
10 x 400ml Ardrox 8903W - W hite
4 x 5 litres Ardrox 8903W - White
1 x 5 litres Ardrox 8903W - White
10 x 400ml Ardrox 800/3 Black M agnetic
4 x 5 litre Ardrox 800/3 Black Magnetic
1 x 5 litre Ardrox 800/3 Black Magnetic
10 x 400ml Ardrox 8530 Fluorescent M agne tic
6 x 500ml Ardrox 8540 Fluorescent Magnetic
Available on request
1 x 500g Ardrox 8510 Fluorescent Powder to be mixed with
Kerosene
Ink
ARDROX Consumables
30
-
8/20/2019 Gammatec Catalogue 2014
36/140
Spare Parts
Product Code DescriptionSB0047 Spare Bulb for UV 100 light
SL0011 Spare filter lens for UV 100 lightNo code Replacement module for LED UV Torch
Spectacles
Product Code DescriptionNCS0037 UV Absorbing Spectacles
Ultraviolet Light MetersProduct Code Description
NCM0017 Goldilux GAL 3L Display
NCM0023Goldilux Mod GUVA-1L UV Light Meter with built-in detector
NCM0025 UVe LUX Dual Light Meter
NCM0004 Goldilux Mod GRP-1 “Smart” Radiometer with Microprocessor display(excluding probe)
NCP0029 Goldilux Mod GUVAP-1L Probe for use with GUV-0LUV Light Meter
NCP0109 Goldilux Mod GAP-1 “Smart” Radiometer UVA Probefor use with GRP-1 Microprocessor.
PM/GSA/SAL-002.01.011.001-REV-2 31
-
8/20/2019 Gammatec Catalogue 2014
37/140
Features
Labino® UVG4-HEAD
The Labino UVG4 is a UV LED Head Lamp designed to free the user’s hands during an inspection.The lamp can be adjusted in three different angles. The operator can switch the angles of the lightduring the inspection. The rubber bands are adjustable and fit helmets as well as heads. The batteryis located in the back of the structure and there are no cables hanging from the lamp.
The UVG4 reach full power instantly. The on/off button is positioned at the back of the lamp to preventaccidental activation. Each head light weights 271 grams (9.4 oz). The lamp contains one ultravioletlight emitting diode (LED) that peaks at 365nm. The life of each LED is estimated at 30,000 hours.The battery has a running time of 3 hours (+/- 5%) and can be recharged from a normal outlet or avehicle cigarrette lighter socket. The lamp is also equipped with a current regulator that keeps the UVintensity constant even when the battery fades. Each unit comes with an extra battery.The Labino Head Light is also available as white light. This small but powerful tool creates more than10,000 lux (930 foot Candles) within a distance of one metre. The distribution angle for white light isspotlight.
Specifications
PM/GSA/SAL-002.01.011.001-REV-2
• Charger for use from electrical outlet• Charger for use in vehicle via cigarette lighter
connection• Two (2) batteries (1+1 extra)
UV source: UV A LED (1)Intensity:Spotlight: >35 000 μw/cm² at 15 cm
25 000 μw/cm² at 38 cm
14 000 μw/cm² at 60 cm
8 000 μw/cm² at 100 cm
Midlight: >32 000 μw/cm² at 15 cm
10 000 μw/cm² at 38 cm
4 500 μw/cm² at 60 cm
1 800 μw/cm² at 100 cm
Visible light:Spotlight: < 7 Lux (
-
8/20/2019 Gammatec Catalogue 2014
38/140
-
8/20/2019 Gammatec Catalogue 2014
39/140
Section 4: Radiographic Testing (RT)
4.1 GAMMA RADIOGRAPHY
4.2.1 P rojector Equipment
Exertus Dual 120 Isotope Projector
The Exertus Dual 120 Projector has the ability to accept Iridium 192 sources or Selenium75 sources. It integrates an improved source channel based on a new helicoidal design,improving maintenance and allows smoother movement of the source assembly inside thedevice, making it easier for the operator and improving safety.
Safety is an integral part of the design of the Exertus Dual 120 Projector – a three coloursignal indicator provides the user with a clear visual guide as to the position of the sourceat all times. Once the source is safe inside the Projector and the Projector is locked (SafeMode) the signal is green. When the source is inside the Projector, but the camera isunlocked and the source assembly locking mechanism is ready to be released a yellowsignal is indicated. When the source is ready for exposure or outside the projector (Exposure Mode) a red signal is indicated.
SpecificationsFeatures
PM/GSA/SAL-002.01.011.001-REV.-2
• Accepts Ir192 or Se75• Helicoildal source channel• Lighter than most of its competitors when
loaded with 4.44 TBq (120 Ci)• Compact design,• Extremely user friendly operation• 3 colour signal safety indicator • Standard and Industrial packages available
• Basic Construction Standards: ISO 3999compliant
• Isotopes:•Ir-192 or Se-75 under special form•Ir-192 half-life: 73.8 days•Se-75 half-life: 119.8 days
• Activity:•Ir-192: 4.44 TBq (120 Ci)
•Se-75: 4.44 TBq (120 Ci)• Surface Dose Rate: Max 2 mSv/h• Total Weight: 22 kg (48.5 lb)• DU Weight: 13 kg (28 lb)
34
-
8/20/2019 Gammatec Catalogue 2014
40/140
SpecificationsFeatures
Exertus Dual 60 Isotope Projector
Basic Construction Standards ISO 3999:2004 CompliantIsotopes Ir-192 or Se-75 under special formIr-192 half life 73.8 daysSe-75 half life 119.8 days
ActivityIr-192 2.22 TBq (60 Ci)Se-75 7.40 TBq (200 Ci)Surface Dose Rate Max. 2mSv/hTotal Weight 18 kg (40 lb)DU Weight 10 kg (22 lb)DimensionsLength 302 mm (11.89’’)Width 124 mm (4.88’’)Height 207 mm (8.15’’)Materials UsedOuter Shell CrNi steel
Shielding Depleted UraniumLabyrinth Tungsten Heavy AlloyType B(U) RUS / 5898 / B(U)-96T
Automatic Source Assembly Locking Mechanismis triggered by the front of the Source Assembly,thus ensuring that the Projector can only be locked
and disconnected with the Source in the SafePositionThree colour signal indicator system.
PM/GSA/SAL-002.01.011.001-REV-2
EXERTUS® DUAL 60 Projector has the ability to accept Ir-192 sources or Selenium 75 sources.This projector incorporates design and safety features that make it flexible and compact. EXERTUS®DUAL 60 incorporates a unique safety feature and a new source channel making it lighter than itscompetitors. Its Source Assembly Locking Mechanism is triggered by the source holder capsule at
the front of the Source Assembly, thereby always assuring the operator that the source has returnedto the safe position. EXERTUS® DUAL 60 projector is ISO 3999:2004 compliant.
35
-
8/20/2019 Gammatec Catalogue 2014
41/140
NCC0171
NCG0061
NCP0175
NCP0151
Exertus Dual 60
Exertus Dual 60 Isotope Projector
Dual 60 Pigtail
Exertus and Gammamat SE Guide Tube
Quick Coupling
Exertus Projector Series GO/NO-GO Gauge
Dual 60 Emergency Shipping Plug
Exertus series Projector Transport Overpack
NCW0001
NCC0171
NCC0059
NCS0119
Reel Type 10m - Exertus and Gamm amat
Series winding Mechanism
2.1m Yellow G uide Tube - Exertus and
Gammamat Series
Source Terminal 65 Ir/Co M18 x 1.5
GAM798 Tungsten Directional Collimator
Exertus Series 17mm S panner
NCC0180
Operations Manual
NCT0039
NCT0266
Dual 60/1 Dual 60/2
Dual 60/1
CP0009
NCP0166
NCT0035
CP0013
NCP0166
Operations Manual
Dual 120/60 Codes and Packages
PM/GSA/SAL-002.01.011.001-REV-2
NCC0180
NCG0061
NCP0150
NCP0151
Exertus D ual 120
Exertus Dual 120 Isotope Projector
Dual 120 Pigtail
Exertus and Gammamat SE Guide Tube
Quick Coupling
Exertus Projector Series GO/NO-GO Gauge
Dual 120 Emergency Shipping Plug
Exertus series Projector Transport Overpack
NCW0001
NCT0039
NCT0266
NCC0059
NCS0119
Exertus Dual 120 standard package
Reel Type 10m - Exertus and G ammamat
Series winding Mechanism
2.1m Yellow Gu ide Tube - Exertus and
Gammamat Series
Source Terminal 65 Ir/Co M18 x 1.5
GAM798 Tungsten Directional Collimator
Exertus Series 17mm Spanner
Operations Manual
Dual 120/1 Dual 120/2Exertus Dual 120 standard package (including) Exertus Dual 120 Industrial package (including)
Dual 120/1
Exertus Dual 60 standard package (including) Exertus Dual 60 standard package (including)
Exertus Dual 60 standard package
Operations Manual
36
-
8/20/2019 Gammatec Catalogue 2014
42/140
SpecificationsFeatures
• Specific for use with Se-75 sources
• Smallest and lightest projector
• 3 Colour Signal Indicator
• Tungsten Shielded -No (Du)
• Clip on collimator
( Ideal for close proximity radiography)• Extremely user friendly
The Exertus Selen Circa projector range is a new generation of “close proximity" Tungstenshielded gamma radiography projectors which has the ability to accept Selenium 75sources. This projector offers the latest design that makes it flexible yet compact.
These Projectors can be used for either normal radiography methods or for radiographywhere close proximity work is needed. The design incorporates a Directional TungstenCollimator which connects directly to the Projector. This reduces the radiation controlledarea significantly and allows operations to continue in the close vicinity.
Safety is an integral part of the Exertus Selen Isotope Projector range – a three coloursignal indicator provides the user with a clear visual guide as to the position of the sourceat all times. Once the source is safe inside the Projector and the Projector is locked (SafeMode) the signal is green. When the source is inside the Projector, but the Projector isunlocked and the source assembly locking mechanism is ready to be released a yellowsignal indicates. When the source is ready for exposure or outside the projector(Exposure Mode) a red signal indicates.
• Basic Construction Standards: ISO 3999 compliant
• Isotopes:• Se-75 under special form• Se75 half-life: 119.8 days
• Activity:• Se-75: 1.48 TBq (40 Ci)• Se-75: 2.96 TBq (80 Ci)• Se-75: 3.7 TBq (100 Ci)
• Surface Dose Rate: Max 2 mSv/h• Total weight:
• 8.4 kg (18.5 lb)• 8.8 kg (19.4 lb)• 9 kg (19.84 lb)
•Tungsten weight:• 4.7 kg (10.36 lb)
• 5 kg (11 lb)• 5.3kg (11.68 lb)
• Dimensions (L x W X H): 203 x 110 x 191 mm• Removable Collimator Weight: 4.3 kg (9.4 lb)
Exertus Selen 40, 80 and 120 Circa
Tungsten Shielded Isotope Projectors
PM/GSA/SAL-002.01.011.001-REV-2 37
-
8/20/2019 Gammatec Catalogue 2014
43/140
Basic Construction Standards ISO 3999:2000 CompliantIsotopes Se-75 under special formSe-75 Half life 119.8 daysActivity
Se-75 Type B - 4.44TBq (120Ci)Type A - 3.0 TBq (81 Ci)
Surface Dose Rate Max. 2mSv/hTotal Weight 7 kg (15.43 lb)DU Weight 2.7 kg (5.95 lb)DU Activity 1.42mCi (52.6 MBq)DimensionsLength 224 mm (8.82’’)Width 100 mm (3.94’’)Height 175 mm (6.89’’)Materials UsedOuter Shell CrNi Steel
Shielding Depleted UraniumSource Channel Tungsten Heavy AlloyType B(U) RUS / 5373 / B(U)-96T
Exertus RID-Se4P Isotope Projector
SpecificationsFeatures
EXERTUS® RID-Se4P Projector has the ability to accept Selenium 75 sources. This projectorincorporates design and safety features that make it flexible, compact and lightweight.EXERTUS®RID-Se4P is ISO 3999:2000 compliant. EXERTUS® RID-Se4P projector also has aunique safety feature not found in competitive products: the Source Assembly Locking Mechanism
is triggered by the front link of the Source Assembly, thereby always assuring the operator that thesource has returned to the safe position.
Automatic Source Assembly Locking Mechanismis triggered by the front of the Source Assembly, thus ensuring that the Projector can only be locked and disconnected with Source in the
Safe Position,Two colour signal indicator system
PM/GSA/SAL-002.01.011.001-REV-238
-
8/20/2019 Gammatec Catalogue 2014
44/140
NCP0151
NCG0061
Exertus Selen Circa 80
Exertus Selen Circa 80 Isotope Projector
Close proximity Collimator
Fitting for Guide Tube
Fitting for Shipment
SR 17 Pigtail
Exertus series Projector Transport Overpack
Exertus Projector Series GO/NO-GO Gauge
Reel Type 10m - Gammam at Ti/TSI/SE Series
2.1m Yellow G uide Tube - E xertus and
Gammamat S eries
GAM800 Tungsten D irectional Collimator 60°
So urce Terminal S E M18 x 1.5
Operations Manual Operations Manual
Circa 80/1
Circa 80/1
Circa 80 / 120 & Rid Codes and Packages
Exertus Selen C irca 80 standerd package (including) Circa 80/2 Exertus Selen Circa 80 Industrial package (including)
Exertus Selen Circa 80 standerd package
PM/GSA/SAL-002.01.011.001-REV-2
NCP0173
Rid Se 4P
Rid Se 4P/1 Rid Se 4P Isotope Projector Package (including)
SR 17 Pigtail
Exertus and Gammatec S E Guide Tube Quick C ouplingNCC0180
Exertus Series Projector Transport Overpack
Emergency Shipping PlugNCP0150
Operations Manual
NCP0151
Rid Se 4P Isotope Projector
NCP0151
NCG0061
Exertus Selen Circa 120
Exertus Selen Circa 120 Isotope Projector
Close proximity Collimator
Fitting for Guide Tube
Fitting for Shipment
SR 17 Pigtail
Exertus series Projector Transport Overpack
Exertus Projector Series GO/NO-GO Gauge
NCW0001
NCT0039
NCC0170
NCT0305
Reel Type 10m - Gammam at Ti/TSI/SE Series
2.1m Yellow Guide Tube - Exertus and
Gammamat Series
GAM800 Tungsten Directional Collimator 60°
Source Terminal SE M18 x 1.5
Operations ManualOperations Manual
Circa 120/1 Exertus Selen Circa 120 standard package (including) Circa 120/2 Exertus Selen Circa 120 Industrial package (including)
Circa 120/1 Exertus Selen Circa 120 standard package
NCP0173
NCP0173
CP0011
NCC0180
NCW000
NCT0039
NCC0170
NCC0305
NCC0180
CP0012
39
-
8/20/2019 Gammatec Catalogue 2014
45/140
In order to provide quality control of industrial products, Cobalt-60 is a preferred isotope forthe radiography of steel. The Exertus Vox 100 Projector is an integration of all the ExertusProjector line and has the ability to accept Co-60 sources.
The Exertus Vox 100 Projector integrates an improved source channel based on a newhelicoidal design, which makes maintenance easier. It also allows smoother movement ofthe source assembly inside the device, making it easier for the operator and improvingsafety.
Safety is an integral part of the design of the Exertus Vox 100 Projector. A three colour signalindicator provides the user with a clear visual guide as to the position of the source at all times.Once the source is safe inside the Projector and the Projector is closed (Safe Mode) the signalis green. When the source is inside the Projector, but the camera is open and ready for exposurea yellow signal indicates. When the source is outside the Projector and in the Exposure Modea red signal indicates.
SpecificationsFeatures
Ex
ertus VOX 100 Isotope Pr ojector
PM/GSA/SAL-002.01.011.001-REV-2
• Helicoidal source channel• 400 Ci option coming• Compact design• Extremely user friendly operation• 3 colour signal safety indicator • Mechanical or electronic windout available
• Isotope: Cobalt 60 under special form• Optimal range of thickness (steel): 70 – 200mm
(2.75 – 7.87”)• Movement of a source along the guide tube:
• Horizontally = up to 8.0m• Vertically = up to 4.0m
• Overall dimensions (max)• Radiation head: 450 x 270 x 320 mm
(11.71 x 10.63 x 12.59”)• Remote control: 850 x 550 x 650 mm
(33.46 x 21.65 x 25.59”)• Weight (max):
• Radiation head: 180 kg (396.83lb)• Electric-powered electromechanical drive:
38kg (83.777lb)• Power supply: 220V, 50Hz• Power (max): 5000W• Certification: B(U)96
40
-
8/20/2019 Gammatec Catalogue 2014
46/140
PM/GSA/SAL-002.01.011.001-REV-2
• Safe working area can be reduced to 1m• Highly portable Se.75 Gamma-Ray Projector• Improved radiographic productivity (24 hour production)
• Versatile (adaptable for contact and ellipse shots)• Flexible Radiation Shielding Mats• Easy adjustable Ellipse stand
GammaSafe Close Proximity Se-75 Radiographic SystemThe GammaSafe radiographic system, when used in conjunction with a Selenium-75 source isdesigned to reduce 'safe working distance' thus reducing production losses as well as down time.
The basic package consists of: Circa or RId Se4P Gamma Projector , CloseProximity Collimator, GammaSafe Clamping Jig and Shielding Mats.
• Ellipse Stand• Mazel Guide Tubes and Collimator • Mazel Mats eg:
• Dimensions: 915 x 305 x 9.5 mm• Shielding: Equivalent to (3.3mm) Pb
• Weight: 10.8 kg (approx)• Temperature range: -85°C to 200°C
Features
Optional Accessories
4.1.2 Close Proximity Systems
41
-
8/20/2019 Gammatec Catalogue 2014
47/140
PM/GSA/SAL-002.01.011.001-REV-2
GammaSafe Codes and Packages
GammaSafe Kits
Can be made up to suit clients requirements with any combination of the following:
Lead Shielding Polyurethane and Tungsten Shielding Silicone Mats available on request.
Standard Package
Code
Rid Se 4P/1
CIRCA 40/80/120 1
NCC0165
NCM0037
NCE0001
NCM0036
NCE0002
NCM0043
NCE0006NCT0169
NCC0065
SI0017
NCC0178
NCS0115
NCW0003
NCC0146
Product
Rid SE 4P Standard Package
Standard Package
Close Proximity Collimator
Lead Large Mat - Silicone
Envelope for Large Mat
Lead Primary Beam Mat - Silicone
Envelope for Primary Beam Mat
Lead Elipse Triangle Mat - Silicone
Envelope for Ellipse Triangle Mat
Flexible Tungsten Shielding Guide Tube 750 mm
GAM 827 Tungsten Directional Collimator
Insert for SR 17 S/Holder for Collimator NCC0065
Gammasafe Conact Shot Projector Clamp
CPC Ellipse Stand (Mat support Included)
Reel Type 7.62 m Winder
Carry Case for Gammasafe System
Qty
1
1
3
3
3
3
2
21
1
1
1
1
1
1
Qty
1
3
3
3
3
2
21
1
1
1
1
1
1
Rid Se4P
Circa
1
2
3
6
5
4
7
8
15
12
14
13
11
10
9
16
3
5
4
7
8
1413
1
2 109
6
42
-
8/20/2019 Gammatec Catalogue 2014
48/140
4.1.3 Projector Accessories
Winding Mechanisms Equipment Gammatec Push/Pull Remote Control Winding Mechanism
Gammatec's Push/Pull Remote Control Winding Mechanism is designed for winding outisotopes on all recognized industrial gamma projectors used in gamma radiographyinspection.
The units are available in either reel or pistol-grip versions. These are of light-weightconstruction and standard accessories include inner drive cable, outer hoses, gearboxand connector fittings.
To ensure a smooth push/pull operation, the robust and lightweight aluminium gearboxhousing incorporates two dust-proof ball races as well as a 100mm diameter gear with acable pressure spring which provides maximum contact between gear and cable at alltimes.
SpecificationsFeatures
Optional Accessories
PM/GSA/SAL-002.01.011.001-REV-2
• Robust & lightweight• Conforms to ISO 3999-1: 2000 Standard• Compatible with all recognised industrial
gamma projectors
• Pistol grip winding mechanism• Customized outer hose (minimum length
7.62m); inner cable• Fittings for all recognized industrial
gamma projectors
• Weight (incl handle): 2.95 kg• Dimensions (l x w h): 152mm x
136mm x 28mm
• Cable entry wrap: 270°• Cable travel: 348 mm per revolution• Gear: designed for Series 40 cable• Material specifications:
• Handle, lid and housing = aluminium• Gear = brass• Bearings = sealed roller bearings• Handle spindle = nylon• Handle pin = tool steel• Guide nipples = stainless steel• Liner = tempered
43
-
8/20/2019 Gammatec Catalogue 2014
49/140
Winding Mechanisim Codes and Packages
Reel Type
Pistol Grip
Pistol Grips and Reels
Product Code Description NCG0059 Pistol Grip for Gammatec GearboxNCR0003 Gammatec Winding Mechanism Reel
PM/GSA/SAL-002.01.011.001-REV-2
Product Code
NCW0038
NCW0003
NCW0001NCW0036
NCW0002
NCW0004
NCW0007
NCW0005
NCW0006
NCW0018
NCW0025
NCW0026
NCW0033
NCW0034
Length
5.0m
7.62m
10.0m15.0m
7.62m
10.0m
15.0m
7.62m
10.0m
7.62m
10.0m
15.0m
7.62m
10.0m
For use with Projector series
EXERTUS Series Projectors and
Gammamat Mod Ti/Tsi/Se Series Projectors
Sentinel 880 Projectors
Teletron / Gammavolt / Kowolux Projectors
Spec 2T and Industrial Nuclear Projectors
GAM80 / 120 Projectors
Product Code
NCW0041
NCW0011NCW0012
NCW0037
NCW0009
NCW0010
NCW0013
NCW0014
Length
5.0m
7.62m10.0m
15.0m
7.62m
10.0m
7.62m
10.0m
For use with Projector series
EXERTUS and Gammamat Mod Ti/Tsi/Se Series Projectors
Sentinel 880 Projectors
Teletron / Gammavolt / Kowolux Projectors
44
-
8/20/2019 Gammatec Catalogue 2014
50/140
Drive Cables with Ballpoint
GO-NO-GO GaugesProduct Code Description
NCG0004 Sentinel 880 and Industrial Nuclear GO/NO-GO Gauge
NCG0006 Gammamat Mod Ti Series GO/NO-GO Gauge
NCG0010 Teletron / Gammavolt / Kowolux GO/NO-GO Gauge
NCG0061 Exertus and Gam mam at Mod Tsi/Se Series GO/NO-GO Gauge
GearboxesProduct code Description
NCG0029 Gammatec MKIV Gearbox for use withTech/Ops, Sentinel and Industrial NuclearDrive Hoses – Steel Gear
Product Code
NCC0173
NCC0017
NCC0030NCC0119
NCC0011
NCC0049
NCC0118
NCC0008
NCC0007
NCC0060
NCC0061
NCC0081NCC0082
Length
5.0m
15.2m
20.0m30.0m
20.0m
15.2m
30.0m
15.2m
20.0m
20.0m
30.0m
15.2m20.0m
For use with Prjector series
EXERTUS Series Projectors and
Gam mam at Mod Ti/TSI/SE Series Projectors
Sentinel 880 and Ind ustrial Nuclear Projectors
Teletron / Gammavolt / Kowolux Projectors
Spec 2T Projectors
GA M80 / 120 Projectors
PM/GSA/SAL-002.01.011.001-REV.2 45
-
8/20/2019 Gammatec Catalogue 2014
51/140
Drive Hoses
Drive Hose Quick Couplings
Product Code Description
NCC0009 EXERTUS Series and Gammamat Mod Ti/Tsi/Se SeriesProjectors
NCC0025 Sentinel Mod 880 Projectors
NCC0091 Spec 2T, Industrial Nuclear Projectors
NCC0147 GAM80 Projectors
Guide Tubes
PM/GSA/SAL-002.01.011.001-REV-2
Product Code
NCH0023