G33M Seriesstatic.highspeedbackbone.net/pdf/MSI_G33M_Series_Manual.pdf · If a problem arises with...

i

G33M SeriesMS-7357 (V1.X) Mainboard

G52-73571X1

ii

Copyright Notice

The material in this document is the intellectual property of MICRO-STARINTERNATIONAL. We take every care in the preparation of this document, but noguarantee is given as to the correctness of its contents. Our products are undercontinual improvement and we reserve the right to make changes without notice.

Trademarks

All trademarks are the properties of their respective owners.

NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trade-marks of NVIDIA Corporation in the United States and/or other countries.AMD, Athlon™, Athlon™ XP, Thoroughbred™, and Duron™ are registered trade-marks of AMD Corporation.Intel® and Pentium® are registered trademarks of Intel Corporation.PS/2 and OS®/2 are registered trademarks of International Business MachinesCorporation.Windows® 95/98/2000/NT/XP are registered trademarks of Microsoft Corporation.Netware® is a registered trademark of Novell, Inc.Award® is a registered trademark of Phoenix Technologies Ltd.AMI® is a registered trademark of American Megatrends Inc.

Revision History

Revision Revision History DateV1.0 First release May 2007

Technical Support

If a problem arises with your system and no solution can be obtained from the user’smanual, please contact your place of purchase or local distributor. Alternatively,please try the following help resources for further guidance.

Visit the MSI website for FAQ, technical guide, BIOS updates, driver updates,and other in f ormat ion: ht tp: / /g lobal .msi.com.tw/ index.php?func=faqIndexContact our technical staff at: http://support.msi.com.tw/

iii

Safety Instructions

CAUTION: Danger of explos ion if bat tery is incorrectly replaced.Replace only with the same or equivalent type recommended by themanufacturer.

1. Always read the safety instructions carefully.2. Keep this User’s Manual for future reference.3. Keep this equipment away from humidity.4. Lay this equipment on a reliable f lat surface before setting it up.5. The openings on the enclosure are for air convection hence protects the equip-

ment from overheating. DO NOT COVER THE OPENINGS.6. Make sure the voltage of the power source and adjust properly 110/220V be-

fore connecting the equipment to the power inlet.7. Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.8. Always Unplug the Power Cord before inserting any add-on card or module.9. All cautions and warnings on the equipment should be noted.10. Never pour any liquid into the opening that could damage or cause electrical

shock.11. If any of the following situations arises, get the equipment checked by service

personnel:Ü The power cord or plug is damaged.Ü Liquid has penetrated into the equipment.Ü The equipment has been exposed to moisture.Ü The equipment does not work well or you can not get it work according to

User’s Manual.Ü The equipment has dropped and damaged.Ü The equipment has obvious sign of breakage.

12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STOR-AGE TEMPERATURE ABOVE 600 C (1400F), IT MAY DAMAGE THE EQUIPMENT.

iv

FCC-B Radio Frequency Interference Statement

This equipment has beentested and found to complywith the limits for a Class Bdigital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accor-dance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the measures listedbelow.

Ü Reorient or relocate the receiving antenna.

Ü Increase the separation between the equipment and receiver.

Ü Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.

Ü Consult the dealer or an experienced radio/television technician for help.

Notice 1The changes or modif ications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.

Notice 2Shielded interface cables and A.C. power cord, if any, must be used in order tocomply with the emission limits.

VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.

Micro-Star InternationalMS-7357

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that

may cause undesired operation.

v

WEEE (Waste Electrical and Electronic Equipment) Statement

viii

CONTENTSCopyright Notice ............................................................................................................... iiTrademarks ....................................................................................................................... iiRevision History ............................................................................................................... iiTechnical Support ............................................................................................................ iiSafety Instructions .......................................................................................................... iiiFCC-B Radio Frequency Interference Statement ........................................................ ivWEEE (Waste Electrical and Electronic Equipment) Statement .................................... vChapter 1 Getting Started ..................................................................................... 1-1

Mainboard Specifications ................................................................................... 1-2Mainboard Layout ................................................................................................ 1-4Packing Checklist ................................................................................................. 1-5

Chapter 2 Hardware Setup ................................................................................... 2-1Quick Components Guide .................................................................................... 2-2CPU (Central Processing Unit) ............................................................................ 2-3Memory................................................................................................................. 2-7Power Supply ...................................................................................................... 2-9Back Panel .......................................................................................................... 2-10Connectors ........................................................................................................ 2-12Jumper ................................................................................................................ 2-19Slots .................................................................................................................... 2-20

Chapter 3 BIOS Setup ............................................................................................. 3-1Entering Setup ..................................................................................................... 3-2The Main Menu ..................................................................................................... 3-4Standard CMOS Features ................................................................................... 3-6Advanced BIOS Features ................................................................................... 3-9Integrated Peripherals ....................................................................................... 3-12Power Management Setup ............................................................................... 3-14PnP/PCI Configurations ...................................................................................... 3-17H/W Monitor ........................................................................................................ 3-19Frequency/Voltage Control ............................................................................... 3-20Load Fail-Safe/ Optimized Defaults ................................................................. 3-24BIOS Setting Password ..................................................................................... 3-25

Appendix A Dual Core Center ............................................................................. A-1Activating Dual Core Center ............................................................................... A-2Main ...................................................................................................................... A-3DOT(Dynamic Over Clocking) ............................................................................. A-5Clock ..................................................................................................................... A-6

ix

Voltage .................................................................................................................A-7FAN Speed ...........................................................................................................A-8Temperature .........................................................................................................A-9User Profile ........................................................................................................A-10

Appendix B Realtek ALC888 Audio ..................................................................... B-1Installing the Realtek HD Audio Driver ................................................................ B-2Software Configuration ...................................................................................... B-4Hardware Setup ................................................................................................ B-19

1-1

Getting Started

Getting StartedChapter 1

Thank you for choosing the G33M Series (MS-7357V1.X) Micro-ATX mainboard. The G33M Seriesmainboards are based on Intel® G33 & ICH9 / ICH9Rchipsets for optimal system efficiency. Designed to fitthe advanced Intel® Core 2 Extreme, Core 2 Quad,Core 2 Duo, Pentium and Celeron processor, the G33MSeries deliver a high performance and professionaldesktop platform solution.

MS-7357 Mainboard

1-2

Mainboard Specifications

Processor Support- Intel® Core 2 Extreme, Core 2 Quad, Core 2 Duo, Pentium andCeleron in the LGA775 package(For the latest information about CPU, please visit http://global.msi.com.tw/index.php?func=cpuform)

Supported FSB- 1333/ 1066/ 800 MHz

Chipset- North Bridge: Intel® G33 chipset- South Bridge: Intel® ICH9 / ICH9R chipsets

Memory Support- DDR2 800/ 667 SDRAM (8GB Max)- 4 DDR2 DIMMs (240pin / 1.8V)(For more information on compatible components, please visit http://global.msi.com.tw/index.php?func=testreport)

LAN- Supports PCIE LAN 10/100/1000 Fast Ethernet by Marvell 88E8056

IEEE 1394 (Optional)- Chip integrated by VIA® VT6308P- Transfer rate is up to 400Mbps

Audio- Chip integrated by Realtek® ALC888- Flexible 8-channel audio with jack sensing- Compliant with Azalia 1.0 Spec- Meet Microsoft Vista Premium SPEC

IDE- 1 IDE port by Marvell 88SE6111- Supports Ultra DMA 66/100/133 mode- Supports PIO, Bus Master operation mode

SATA- 4 SATA II ports by ICH9 base (2 eSATA for Windows Vista)- 6 SATA II ports by ICH9R- 1 SATA II port by Marvell 88SE6111- Supports storage and data transfers at up to 300MB/s

Floppy- 1 floppy port- Supports 1 FDD with 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB

1-3

Getting Started

ConnectorsBack panel- 1 PS/2 mouse port- 1 PS/2 keyboard port- 6 USB 2.0 ports- 1 IEEE 1394 port (Optional)- 1 VGA port- 1 LAN jack (10/100/1000)- 2 eSATA ports (Hot plug supported by ICH9R)- 6 flexible audio jacks

On-Board Pinheaders/ Connectors- 1 Front Panel Audio pinheader- 1 CD-In connector- 1 SPDIF-Out (or SPDIF-In) pinheader- 1 IEEE 1394 pinheader (Optional)- 3 USB 2.0 pinheaders- 1 Chassis Intrusion Switch pinheader- 1 Serial port pinheader

Slots- 1 PCI Express x16 slot- 1 PCI Express x1 slot- 2 PCI slots- Support 3.3V/ 5V PCI bus Interface

Form Factor- Micro-ATX (24.4cm X 24.4cm)

Mounting- 8 mounting holes

MS-7357 Mainboard

1-4

G33M Series(MS-7357 V1.X) Micro-ATX Mainboard

Mainboard Layout

Top: MouseBottom: Keyboard

Top:USB Ports

Bottom:1394 Port (Optional)VGA Port

Top: LAN PortBottom: USB Ports

eSATA Ports

T: Line-InM: Line-OutB: MicT: RS-OutM: CS-OutB: SS-Out

CPUFAN1

PCI-E1

PCIE1X1

PCI1

PCI2

LAN CHIP

Codec

JAUD1

JCD_IN1

JSPDIF1

SYSFAN1

J1394_2 (Optional) JUSB3 JUSB1 JUSB2 JFP1 JFP2

IntelICH9 / ICH9R

JCASE1

IntelG33

BATT +

JCO

M1

ATX

1

FDD

1

IDE

1 Marvell88SE6111D

IMM

_A

1

DIM

M_

A2

DIM

M_

B1

DI M

M_

B2

SA

TA1

SA T

A2

JPW

1

SA

TA7

JBAT1

VIA

VT6

3 08P

(O

ptio

nal)

S

ATA

3(

Opt

iona

l)

(O

ptio

nal)

S

ATA

4

1-5

Getting Started

Packing Checklist

Power Cable (Optional) SATA Cable

User’s Guide

MSI motherboard MSI Driver/Utility CD

* The pictures are for reference only and may vary from the packing contents of theproduct you purchased.

Back IO Shield

Standard Cable forIDE Devices (Optional)

1394 Bracket (Optional)

USB Bracket (Optional)

2-1

Hardware Setup

Hardware SetupChapter 2

This chapter provides you with the information abouthardware setup procedures. While doing the installation,be careful in holding the components and follow theinstallation procedures. For some components, if youinstall in the wrong orientation, the components will notwork properly.

Use a grounded wrist strap before handling computercomponents. S tatic elec tr ic ity may damage thecomponents.

2-2

MS-7357 Mainboard

Quick Components Guide

Back Panel

I/O, p.2-10

DDR2 DIMMs,

p.2-7

JFP1~2,

p.2-18

JPW1,p.2-9

SATA1~4&7,p.2-13

CPUFAN1,

p.2-14

JUSB1~3,

p.2-16

SYSFAN1,

p.2-14

PCI Slots,

p.2-20

FDD1,p.2-12

PCI Express Slots,p.2-20

CPU,

p.2-3

JAUD1,

p.2-15

JCD_IN1,

p.2-14

JCASE1,p.2-14

ATX1,p.2-9

JSPDIF1,

p.2-17

J1394_2,

p.2-17

JBAT1,

p.2-19

JCOM1,

p.2-16

IDE1,

p.2-12

2-3

Hardware Setup

CPU (Central Processing Unit)

This mainboard supports Intel® Core 2 Extreme, Core 2 Quad, Core 2 Duo, Pentium andCeleron processor in LGA 775 package. When you are installing the CPU, makesure to install the cooler to prevent overheating. If you do not have the CPUcooler, consult your dealer before turning on the computer. For the latest informationabout CPU, please visit http://global.msi.com.tw/index.php?func=cpuform

Introduction to LGA 775 CPUThe surface of LGA 775 CPU.Remember to apply some ther-mal paste on it for better heatdispersion.

Yellow triangle is the Pin 1 indicator

The pin-pad side of LGA 775CPU.

Yellow triangle is the Pin 1 indicator

Alignment Key Alignment Key

Important

OverheatingOverheating will seriously damage the CPU and system. Always make surethe cooling fan can work properly to protect the CPU from overheating. Makesure that you apply an even layer of thermal paste (or thermal tape) betweenthe CPU and the heatsink to enhance heat dissipation.Replaceing the CPUWhile replacing the CPU, always turn off the ATX power supply or unplug thepower supply’s power cord from the grounded outlet first to ensure the safetyof CPU.OverclockingThis mainboard is designed to support overclocking. However, please makesure your components are able to tolerate such abnormal setting, whiledoing overclocking. Any attempt to operate beyond product specifications isnot recommended. We do not guarantee the damages or risks causedby inadequate operation or beyond product specifications.

2-4

MS-7357 Mainboard

Important

1. Confirm if your CPU cooler is firmly installed before turning on your system.2. Do not touch the CPU socket pins to avoid damaging.3. The availability of the CPU land side cover depends on your CPU packing.

2. Remove the cap from lever hingeside (as the arrow shows).

1. The CPU socket has a plastic capon it to protect the contact fromdamage. Before you install the CPU,always cover it to protect the socketpin.

CPU & Cooler InstallationWhen you are installing the CPU, make sure the CPU has a cooler attached onthe top to prevent overheating. Meanwhile, do not forget to apply some thermalpaste on CPU before installing the heat sink/cooler fan for better heat dispersion.Follow the steps below to install the CPU & cooler correctly. Wrong installation willcause the damage of your CPU & mainboard.

3. The pins of socket reveal. 4. Open the load lever.

2-5

Hardware Setup

6. After confirming the CPU directionfor correct mating, put down theCPU in the socket housing frame.Be sure to grasp on the edge ofthe CPU base. Note that the align-ment keys are matched.

8. Cover the load plate onto thepackage.

7. Visually inspect if the CPU isseated well into the socket. If not,take out the CPU with pure verticalmotion and reinstall.

alignmentkey

5. Lift the load lever up and open theload plate.

2-6

MS-7357 Mainboard

10. Align the holes on the mainboardwith the heatsink. Push down thecooler unti l i ts four c lips getwedged into the holes of themainboard.

12. Turn over the mainboard to con-firm that the clip-ends are cor-rectly inserted.

11. Press the four hooks down to fas-ten the cooler. Then rotate the lock-ing switch (refer to the correct di-rection marked on it) to lock thehooks.

9. Press down the load lever lightlyonto the load plate, and then se-cure the lever with the hook underretention tab.

lockingswitch

Important

1. Read the CPU status in BIOS (Chapter 3).2. Whenever CPU is not installed, always protect your CPU socket pin with the

plastic cap covered (shown in Figure 1) to avoid damaging.3. Mainboard photos shown in this section are for demonstration of the CPU/

cooler installation only. The appearance of your mainboard may vary depend-ing on the model you purchase.

2-7

Hardware Setup

Memory

DDR2240-pin, 1.8V

1 DIMM_A1 DIMM_A2 DIMM_B1

DIMM_B2

2 DIMM_A1

DIMM_A2 DIMM_B1

DIMM_B2

3 DIMM_A1

DIMM_A2 DIMM_B1

DIMM_B2

64x2=128 pin56x2=112 pin

These DIMM slots are used for installing memory modules.For more information on compatible components, please visit http://global.msi.com.tw/index.php?func=testreport

Dual-Channel mode Population RuleIn Dual-Channel mode, the memory modules can transmit and receive data with twodata bus lines simultaneously. Enabling Dual-Channel mode can enhance the systemperformance. Please refer to the following illustrations for population rules underDual-Channel mode.

EmptyInstalled

2-8

MS-7357 Mainboard

Installing Memory Modules1. The memory module has only one notch on the center and will only fit in the right

orientation.2. Insert the memory module vertically into the DIMM slot. Then push it in until the

golden finger on the memory module is deeply inserted in the DIMM slot.

3. The plastic clip at each side of the DIMM slot will automatically close.

Important

You can barely see the golden finger if the memory module is properly insertedin the DIMM slot.

Volt Notch

Important

- DDR2 memory modules are not interchangeable with DDR and the DDR2standard is not backwards compatible. You should always install DDR2memory modules in the DDR2 DIMM slots.

- In Dual-Channel mode, make sure that you install memory modules of thesame type and density in different channel DIMM slots.

- To enable successful system boot-up, always insert the memory modulesinto the DIMM1 first.

- Due to the chipset resource deployment, the system density will only bedetected up to 7+GB (not full 8GB) when each DIMM is installed with a 2GBmemory module.

2-9

Hardware Setup

Power Supply

PIN SIGNAL

13 +3.3V14 -12V15 GND16 PS-ON#17 GND18 GND19 GND20 Res21 +5V22 +5V23 +5V24 GND

PIN SIGNAL

1 +3.3V 2 +3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 PWR OK 9 5VSB10 +12V11 +12V12 +3.3V

Pin Definition

pin 12

pin 13

Important

1. Maker sure that all the connectors are connected to proper ATX power sup-plies to ensure stable operation of the mainboard.

2. Power supply of 350 watts (and above) is highly recommended for systemstability.

ATX 24-Pin Power Connector: ATX1This connector allows you to connect an ATX 24-pin power supply.To connect the ATX 24-pin power supply, make sure the plug of thepower supply is inserted in the proper orientation and the pins arealigned. Then push down the power supply firmly into the connector.You may use the 20-pin ATX power supply as you like. If you’d liketo use the 20-pin ATX power supply, please plug your power sup-ply along with pin 1 & pin 13 (refer to the image at the right hand).There is also a foolproof design on pin 11, 12, 23 & 24 to avoidwrong installation.

PIN SIGNAL

1 GND2 GND3 12V4 12V

Pin Definition

ATX 12V Power Connector: JPW1This 12V power connector JPW1 is used to provide power to the CPU.

1

ATX1

1224

13

JPW1

1 3

42

2-10

MS-7357 Mainboard

Mouse/ Keyboard ConnectorThe standard PS/2® mouse/keyboard DIN connector is for a PS/2® mouse/keyboard.

USB PortThe USB (Universal Serial Bus) port is for attaching USB devices such as keyboard,mouse, or other USB-compatible devices.

1394 Port (Optional)The IEEE1394 port on the back panel provides connection to IEEE1394 devices.

VGA PortThe DB15-pin female connector is provided for monitor.

LAN (RJ-45) JackThe standard RJ-45 jack is for connection to single Local Area Network (LAN). Youcan connect a network cable to it.

eSATA PortThe eSATA port is for attaching the eSATA external hard drive.(about specif ication content please refer to Intel website)

Back Panel

Keyboard

USB Port

Mouse LAN JackRS-Out

CS-Out

SS-Out

VGA Port1394 Port(Optional)

Line-In

eSATA Port

Line-Out

Mic

USB Port

LED Color LED State condition

Off LAN link is not established.

Left Orange On (steady state) LAN link is established.

On (brighter & pulsing) The computer is communicating with another computer on the LAN.

Green Off 10 Mbit/sec data rate is selected.

Right On 100 Mbit/sec data rate is selected.Orange On 1000 Mbit/sec data rate is selected.

Link IndicatorActivity Indicator

2-11

Hardware Setup

Audio PortsThese audio connectors are used for audio devices. You can differentiate the colorof the audio jacks for different audio sound effects.

Line-In (Blue) - Line In, is used for external CD player, tapeplayer or other audio devices.

Line-Out (Green) - Line Out, is a connector for speakers or headphones. Mic (Pink) - Mic, is a connector for microphones. RS-Out (Black) - Rear-Surround Out in 4/ 5.1/ 7.1 channel mode. CS-Out (Orange) - Center/ Subwoofer Out in 5.1/ 7.1 channel mode. SS-Out (Gray) - Side-Surround Out 7.1 channel mode.

Important

eSATA for Windows VISTA (ICH9 Base)1. Please enable AHCI mode under BIOS set up manual then install VISTA OS

and you can use eSATA functionality.2. AHCI mode is not supported while you install Windows XP with ICH9 Base.eSATA for all (ICH9R)You can fully use eSATA functionality while you operate your system underWindows XP or Windows VISTA (AHCI/RAID mode)

2-12

MS-7357 Mainboard

Connectors

Floppy Disk Drive Connector: FDD1This connector supports 360KB, 720KB, 1.2MB, 1.44MB or 2.88MB floppy disk drive.

IDE Connector: IDE1This connector supports IDE hard disk drives, optical disk drives and other IDE devices.

Important

If you install two IDE devices on the same cable, you must configure thedrives separately to master / slave mode by setting jumpers. Refer to IDEdevice ’s documentation supplied by the vendors for jumper sett inginstructions.

IDE1

FDD1

2-13

Hardware Setup

Serial ATA Connector: SATA1/ SATA2/ SATA3/ SATA4/ SATA7(SATA3 and SATA4 are optional)This connector is a high-speed Serial ATA interface port. Each connector can con-nect to one Serial ATA device.

SATA3(Optional)

SATA4(Optional)

SATA1 SATA2

SATA7

Important

Please do not fold the Serial ATA cable into 90-degree angle. Otherwise,data loss may occur during transmission.

2-14

MS-7357 Mainboard

Chassis Intrusion Switch Connector: JCASE1This connector connects to a 2-pin chassis switch. If the chassis is opened, theswitch will be short. The system will record this status and show a warning mes-sage on the screen. To clear the warning, you must enter the BIOS utility and clear therecord.

CD-In Connector: JCD_IN1This connector is provided for external audio input.

Fan Power Connectors: CPUFAN1, SYSFAN1The fan power connectors support system cooling fan with +12V. When connectingthe wire to the connectors, always note that the red wire is the positive and shouldbe connected to the +12V; the black wire is Ground and should be connected to GND.If the mainboard has a System Hardware Monitor chipset on-board, you must use aspecially designed fan with speed sensor to take advantage of the CPU fan control.

Important

1. Please refer to the recommended CPU fans at processor’s official websiteor consult the vendors for proper CPU cooling fan.

2. Fan cooler set with 3 or 4 pins power connector are both available forCPUFAN1.

3. CPUFAN1 supports fan control. You can setup it in H/W Monitor of BIOSSetup. You can install Dual Core Center utility that will automaticallycontrol the CPU fan speed according to the actual CPU temperature.

SYSFAN1CPUFAN1

SENSOR+12VGND

CONTROL

GN

D+1

2VS

EN

SO

RC

ONT

RO

L

JCASE12

GN

DC

INTR

U

1

JCD_IN1

GND

RL

2-15

Hardware Setup

Front Panel Audio Connector: JAUD1This connector allows you to connect the front panel audio and is compliant withIntel® Front Panel I/O Connectivity Design Guide.

JAUD112

910

PIN SIGNAL DESCRIPTION

1 MIC_L Microphone - Left channel2 GND Ground3 MIC_R Microphone - Right channel4 PRESENCE# Active low signal-signals BIOS that a High Definition Audio dongle

is connected to the analog header. PRESENCE# = 0 when aHigh Definition Audio dongle is connected

5 LINE out_R Analog Port - Right channel6 MIC_JD Jack detection return from front panel microphone JACK17 Front_JD Jack detection sense line from the High Definition Audio CODEC

jack detection resistor network8 NC No control9 LINE out_L Analog Port - Left channel10 LINEout_JD Jack detection return from front panel JACK2

HD Audio Pin Definition


1 MIC Microphone input signal2 GND Ground3 MIC_PWR Microphone power4 NC No Control5 LINE out_R Right channel audio signal to front panel6 NC No Control7 NC No Control8 Key No pin9 LINE out_L Left channel audio signal to front panel10 NC No Control

AC’97 Audio Pin Definition

2-16

MS-7357 Mainboard

Front USB Connector: JUSB1/ JUSB2/ JUSB3This connector, compliant with Intel® I/O Connectivity Design Guide, is ideal for con-necting high-speed USB interface peripherals such as USB HDD, digital cameras,MP3 players, printers, modems and the like.

Serial Port Connector: JCOM1This connector is a 16550A high speed communication port that sends/receives 16bytes FIFOs. You can attach a serial device.

PIN SIGNAL PIN SIGNAL1 VCC 2 VCC

3 USB0- 4 USB1-5 USB0+ 6 USB1+

7 GND 8 GND

9 Key (no pin) 10 USBOC

Pin Definition

12

910

JUSB1/2/3

USB 2.0 Bracket(Optional)

Important

Note that the pins of VCC and GND must be connected correctly to avoidpossible damage.


1 DCD Data Carry Detect 2 SIN Serial In or Receive Data 3 SOUT Serial Out or Transmit Data 4 DTR Data Terminal Ready 5 GND Ground 6 DSR Data Set Ready 7 RTS Request To Send 8 CTS Clear To Send 9 RI Ring Indicate

Pin Definition

1 2

9

JCOM1

2-17

Hardware Setup

S/PDIF Bracket (Optional)

S/PDIF-Out Connector: JSPDIF1This connector is used to connect S/PDIF (Sony & Philips Digital Interconnect Format)interface for digital audio transmission.

IEEE1394 Connector: J1394_2 (Optional)This connector allows you to connect the IEEE1394 device via an optional IEEE1394bracket.

Pin Definition

PIN SIGNAL PIN SIGNAL

1 TPA+ 2 TPA-

3 Ground 4 Ground

5 TPB+ 6 TPB-

7 Cable power 8 Cable power

9 Key (no pin) 10 Ground

J1394_2 1 2

9 10

IEEE1394 Bracket (Optional)

JSPDIF1

VCC

SPDIF

GND

2-18

MS-7357 Mainboard


1 HD_LED + Hard disk LED pull-up2 FP PWR/SLP MSG LED pull-up3 HD_LED - Hard disk active LED4 FP PWR/SLP MSG LED pull-up5 RST_SW - Reset Switch low reference pull-down to GND6 PWR_SW - Power Switch high reference pull-down to GND7 RST_SW + Reset Switch high reference pull-up8 PWR_SW + Power Switch low reference pull-up9 RSVD_DNU Reserved. Do not use.

JFP1 Pin Definition


1 GND Ground2 SPK- Speaker-3 SLED Suspend LED4 BUZ+ Buzzer+5 PLED Power LED6 BUZ- Buzzer-7 NC No connection8 SPK+ Speaker+

JFP2 Pin Definition

12

910JFP1

HDDLED

ResetSwitch

PowerLED

PowerSwitch

+ +

-

- -

+

78

PowerLED

Speaker

12JFP2

--+

+

Front Panel Connectors: JFP1, JFP2These connectors are for electrical connection to the front panel switches and LEDs.The JFP1 is compliant with Intel® Front Panel I/O Connectivity Design Guide.

2-19

Hardware Setup

Jumpers

Clear CMOS Jumper: JBAT1There is a CMOS RAM onboard that has a power supply from an external battery tokeep the data of system configuration. With the CMOS RAM, the system can auto-matically boot OS every time it is turned on. If you want to clear the system configuration,set the jumper to clear data.

Important

You can clear CMOS by shorting 2-3 pin while the system is off. Then returnto 1-2 pin position. Avoid clearing the CMOS while the system is on; it willdamage the mainboard.

JBAT11

Clear Data

3

1

Keep Data

3

1

2-20

MS-7357 Mainboard

Slots

PCI (Peripheral Component Interconnect) Express SlotThe PCI Express slot supports the PCI Express interface expansion card.The PCI Express x 16 supports up to 4.0 GB/s transfer rate.The PCI Express x 8 supports up to 2.0 GB/s transfer rate.The PCI Express x 4 supports up to 1.0 GB/s transfer rate.The PCI Express x 1 supports up to 250 MB/s transfer rate.

PCI (Peripheral Component Interconnect) SlotThe PCI slot supports LAN card, SCSI card, USB card, and other add-on cards thatcomply with PCI specifications.

PCI Express x16 Slot

PCI Express x1 Slot

32-bit PCI Slot

Important

1. When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to configure any necessary hardware or software settings for the ex pansion card, such as jumpers, switches or BIOS configuration.

PCI Interrupt Request RoutingThe IRQ, acronym of interrupt request line and pronounced I-R-Q, are hardware linesover which devices can send interrupt signals to the microprocessor. The PCI IRQpins are typically connected to the PCI bus pins as follows:

Order 1 Order 2 Order 3 Order 4

PCI Slot 1 INT A# INT B# INT C# INT D#

PCI Slot 2 INT B# INT C# INT D# INT A#

3-1

BIOS Setup

Chapter 3

BIOS Setup

This chapter provides information on the BIOS Setupprogram and allows you to configure the system foroptimum use.You may need to run the Setup program when:

² An error message appears on the screen during thesystem booting up, and requests you to run SETUP.

² You want to change the default settings for cus-tomized features.

3-2

MS-7357 Mainboard

Entering Setup

Important

1. The items under each BIOS category described in this chapter are undercontinuous update for better system performance. Therefore, the descrip-tion may be slightly different from the latest BIOS and should be held forreference only.

2. Upon boot-up, the 1st line appearing after the memory count is the BIOSversion. It is usually in the format:

A7357IMS V1.0 040307 where:

1st digit refers to BIOS maker as A = AMI, W = AWARD, and P =PHOENIX.2nd - 5th digit refers to the model number.6th digit refers to the chipset as I = Intel, N = nVidia, and V = VIA.7th - 8th digit refers to the customer as MS = all standard customers.V1.0 refers to the BIOS version.040307 refers to the date this BIOS was released.

Power on the computer and the system will start POST (Power On Self Test) process.When the message below appears on the screen, press <DEL> key to enter Setup.

Press DEL to enter SETUP

If the message disappears before you respond and you still wish to enter Setup,restart the system by turning it OFF and On or pressing the RESET button. You mayalso restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.

3-3

BIOS Setup

Getting HelpAfter entering the Setup menu, the first menu you will see is the Main Menu.

Main MenuThe main menu lists the setup functions you can make changes to. You can use thearrow keys ( ↑↓ ) to select the item. The on-line description of the highlighted setupfunction is displayed at the bottom of the screen.

Sub-MenuIf you find a right pointer symbol (as shown in the rightview) appears to the left of certain fields that means asub-menu can be launched from this field. A sub-menucontains additional options for a field parameter. Youcan use arrow keys ( ↑↓ ) to highlight the f ield andpress <Enter> to call up the sub-menu. Then you can use the control keys to entervalues and move from field to field within a sub-menu. If you want to return to themain menu, just press the <Esc >.

General Help <F1>The BIOS setup program provides a General Help screen. You can call up this screenfrom any menu by simply pressing <F1>. The Help screen lists the appropriate keysto use and the possible selections for the highlighted item. Press <Esc> to exit theHelp screen.

Control Keys

<↑> Move to the previous item<↓> Move to the next item<←> Move to the item in the left hand<→> Move to the item in the right hand<Enter> Select the item<Esc> Jumps to the Exit menu or returns to the main menu from a

submenu<+/PU> Increase the numeric value or make changes<-/PD> Decrease the numeric value or make changes<F6> Load Optimized Defaults<F8> Load Fail-Safe Defaults<F10> Save all the CMOS changes and exit

3-4

MS-7357 Mainboard

Standard CMOS FeaturesUse this menu for basic system configurations, such as time, date etc.

Advanced BIOS FeaturesUse this menu to setup the items of AMI® special enhanced features.

Integrated PeripheralsUse this menu to specify your settings for integrated peripherals.

Power Management SetupUse this menu to specify your settings for power management.

PnP/PCI ConfigurationsThis entry appears if your system supports PnP/PCI.

H/W MonitorThis entry shows your PC health status.

Frequency/Voltage ControlUse this menu to specify your settings for frequency/voltage control and overclocking.

Load Fail-Safe DefaultsUse this menu to load the default values set by the BIOS vendor for stable systemperformance.

The Main Menu

3-5

BIOS Setup

Load Optimized DefaultsUse this menu to load the default values set by the mainboard manufacturer specifi-cally for optimal performance of the mainboard.

BIOS Setting PasswordUse this menu to set the password for BIOS.

Save & Exit SetupSave changes to CMOS and exit setup.

Exit Without SavingAbandon all changes and exit setup.

3-6

MS-7357 Mainboard

The items in Standard CMOS Features Menu includes some basic setup items. Usethe arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to selectthe value you want in each item.

Standard CMOS Features

Date (MM:DD:YY)This allows you to set the system to the date that you want (usually the current date).The format is <day><month> <date> <year>.

day Day of the week, from Sun to Sat, determined byBIOS. Read-only.

month The month from Jan. through Dec.date The date from 1 to 31 can be keyed by numeric function keys.year The year can be adjusted by users.

Time (HH:MM:SS)This allows you to set the system time that you want (usually the current time). Thetime format is <hour> <minute> <second>.

SATA1/ 2/ 3/ 4/ 5/ 6Press <Enter> to enter the sub-menu, and the following screen appears:(SATA3 and SATA4 are for ICH9R only, SATA5 and SATA6 are eSATA.)

3-7

BIOS Setup

Device/ Vendor/ SizeIt will showing the device information that you connected to the SATA connector.

LBA/Large ModeThis allows you to enable or disable the LBA Mode. Setting to Auto enables LBAmode if the device supports it and the devices is not already formatted with LBAmode disabled.

DMA ModeSelect DMA Mode.

Hard Disk S.M.A.R.T.This allows you to activate the S.M.A.R.T. (Self-Monitoring Analysis & ReportingTechnology) capability for the hard disks. S.M.A.R.T. is a utility that monitorsyour disk status to predict hard disk failure. This gives you an opportunity tomove data from a hard disk that is going to fail to a safe place before the harddisk becomes offline.

SATA1~6 are appearing when you connect the HD devices to the SATA con-nector on the mainboard. Due to the IDE1 & SATA7 is controlled by Marvell88SE6111, the BIOS will not detect the IDE & SATA device and willnot show the status.

Important

3-8

MS-7357 Mainboard

Floppy Drive AThis item allows you to set the type of floppy drives installed. Available options:[None], [360K, 5.25 in.], [1.2M, 5.25 in.], [720K, 3.5 in.], [1.44M, 3.5 in.], [2.88M, 3.5 in.].

System InformationPress <Enter> to enter the sub-menu, and the following screen appears:

This sub-menu shows the CPU information, BIOS version and memory status ofyour system (read only).

3-9

BIOS Setup

Advanced BIOS Features

Boot Sector ProtectionThis function protects the BIOS from accidental corruption by unauthorized users orcomputer viruses. When enabled, the BIOS’ data cannot be changed when attempt-ing to update the BIOS with a Flash utility. To successfully update the BIOS, you’llneed to disable this Flash BIOS Protection function.You should enable this function at all times. The only time when you need to disableit is when you want to update the BIOS. After updating the BIOS, you should immedi-ately re-enable it to protect it against viruses.

Full Screen Logo DisplayThis item enables you to show the company logo on the bootup screen. Settings are:

[Enabled] Shows a still image (logo) on the full screen at boot.[Disabled] Shows the POST messages at boot.

Quick BootingSetting the item to [Enabled] allows the system to boot within 10 seconds since it willskip some check items.

Boot Up Num-Lock LEDThis setting is to set the Num Lock status when the system is powered on. Setting to[On] will turn on the Num Lock key when the system is powered on. Setting to [Off]will allow users to use the arrow keys on the numeric keypad.

3-10

MS-7357 Mainboard

IOAPIC FunctionThis field is used to enable or disable the APIC (Advanced Programmable InterruptController). Due to compliance with PC2001 design guide, the system is able to run inAPIC mode. Enabling APIC mode will expand available IRQ resources for the system.

MPS Table VersionThis field allows you to select which MPS (Multi-Processor Specification) version tobe used for the operating system. You need to select the MPS version supported byyour operating system. To find out which version to use, consult the vendor of youroperating system.

CPU FeaturePress <Enter> to enter the sub-menu and the following screen appears:

Execute Bit SupportIntel's Execute Bit Support functionality can prevent certain classes of malicious"buffer overflow" attacks when combined with a supporting operating system.This functionality allows the processor to classify areas in memory by whereapplication code can execute and where it cannot. When a malicious wormattempts to insert code in the buffer, the processor disables code execution,preventing damage or worm propagation.

Set Limit CPUID MaxVal to 3The Max CPUID Value Limit is designed to limit the listed speed of the processorto older operating systems.

Chipset FeaturePress <Enter> to enter the sub-menu and the following screen appears:

HPETThe HPET (High Precision Event Timers) is a component that is part of the chipset.You can to enable it, and will provide you with the means to get to it via thevarious ACPI methods.

3-11

BIOS Setup

VGA Share MemoryThe system shares memory to the onboard VGA card. This setting controls theexact memory size shared to the VGA card.

DVMT Mode SelectThis item allows you to set the mode for the graphics core.[Fixed] mode, a fixed-size fragment of the system memory is allocated to thegraphics core. It can only be used by the graphics core.[DVMT] mode, the driver of the graphics core uses the system memory like anyother OS component or application does.

Boot SequencePress <Enter> to enter the sub-menu and the following screen appears:

1st/ 2nd/ 3rd Boot DeviceThe items allow you to set the f irst/ second/ third boot device where BIOSattempts to load the disk operating system.

Boot From Other DeviceSetting the option to [Yes] allows the system to try to boot from other device. ifthe system fails to boot from the 1st/ 2nd/ 3rd boot device.

3-12

MS-7357 Mainboard

Integrated Peripherals

USB ControllerThis setting allows you to enable/disable the onboard USB controller.

USB Device Legacy SupportSelect [Enabled] if you need to use a USB-interfaced device in the operating system.

Onboard LAN ControllerThis item is used to enable/disable the onboard LAN controller.

LAN Option ROMThis item is used to decide whether to invoke the Boot ROM of the LAN controller.

Onboard IEEE1394 ControllerThis item allows you to enable/disable the onboard IEEE1394 controller.

Extra IDE ControllerThis setting is used to enable/disable the onboard IDE controller.

HD Audio ControllerThis setting is used to enable/disable the onboard audio controller.

3-13

BIOS Setup

On-Chip ATA DevicesPress <Enter> to enter the sub-menu and the following screen appears:

PCI IDE BusMasterSet this option to [Enabled] to specify that the IDE controller on the PCI local bushas bus mastering capability.

RAID Mode (for ICH9R only)The SATA RAID Mode supports RAID0,1,5,10. If AHCI is chosen, it allows you toenable SATA Stagger Spinup Support(not RAID mode) and take all hard disks onboard as master.

I/O DevicesPress <Enter> to enter the sub-menu and the following screen appears:

COM Port 1This item specifies the base I/O port addresses of the onboard Serial Port 1(COM 1). Selecting [Auto] allows AMIBIOS to automatically determine the correctbase I/O port address.

3-14

MS-7357 Mainboard

Power Management Setup

ACPI FunctionThis item is to activate the ACPI (Advanced Configuration and Power ManagementInterface) Function. If your operating system is ACPI-aware, such as Windows 2000/XP, select [Enabled].

ACPI Standby StateThis item specif ies the power saving modes for ACPI function. If your operatingsystem supports ACPI, such as Windows 2000/ XP , you can choose to enter theStandby mode in S1(POS) or S3(STR) fashion through the setting of this field. Set-tings are:

[S1] The S1 sleep mode is a low power state. In this state, no systemcontext is lost (CPU or chipset) and hardware maintains all systemcontext.

[S3] The S3 sleep mode is a lower power state where the in formation ofsystem configuration and open applications/files is saved to mainmemory that remains powered while most other hardware components turn off to save energy. The information stored in memory willbe used to restore the system when a “wake up” event occurs.

Important

S3-related functions described in this section are available only when yourBIOS supports S3 sleep mode.

3-15

BIOS Setup

Re-Call VGA BIOS From S3When ACPI Standby State is set to [S3], users can select the options in this field.Selecting [Enabled] allows BIOS to call VGABIOS to initialize the VGA card whensystem wakes up (resumes) from S3 sleep state. The system resume time is short-ened when you disable the function, but system will need an VGA driver to initializethe VGA card. Therefore, if the VGA driver of the card does not support the initializa-tion feature, the display may work abnormally or not function after resuming from S3.

Suspend Time Out (Minute)If system activity is not detected for the length of time specified in this f ield, alldevices except CPU will be shut off.

Power Button FunctionThis feature sets the function of the power button. Settings are:

[Power Off] The power button functions as normal power off button.[Suspend When you press the power button, the computer enters the

suspend/sleep mode, but if the button is pressed for morethan four seconds, the computer is turned off.

Restore On AC Power LossThis item specifies whether your system will reboot after a power failure or interruptoccurs. Settings are:

[Off] Always leaves the computer in the power off state.[On] Always leaves the computer in the power on state.[Last State] Restores the system to the status before power failure

or interrupt occurred.

Wakeup Event SetupPress <Enter> and the following sub-menu appears:

Resume From S3 By USB DeviceThe item allows the activity of the USB device to wake up the system from S3(Suspend to RAM) sleep state.

3-16

MS-7357 Mainboard

Resume From S3 By PS/2 KeyboardThis setting determines whether the system will be awakened from what powersaving modes when input signal of the PS/2 keyboard is detected.

Resume From S3 By PS/2 MouseThis setting determines whether the system will be awakened from what powersaving modes when input signal of the PS/2 mouse is detected.

Resume By PCI Device (PME#)When set to [Enabled], the feature allows your system to be awakened from thepower saving modes through any event on PME (Power Management Event).

Resume By PCI-E DeviceWhen set to [Enabled], the feature allows your system to be awakened from thepower saving modes through any event on PCI Express device.

Resume By RTC AlarmThe field is used to enable or disable the feature of booting up the system on ascheduled time/date.

3-17

BIOS Setup

Primary Graphic’s AdapterThis setting specifies which graphics card is your primary graphics adapter.

PCI Latency TimerThis item controls how long each PCI device can hold the bus before another takesover. When set to higher values, every PCI device can conduct transactions for alonger time and thus improve the effective PCI bandwidth. For better PCI performance,you should set the item to higher values.

PCI Slot 1/ 2 IRQThese items specify the IRQ line for each PCI slot.

PnP/PCI Configurations

This section describes configuring the PCI bus system and PnP (Plug & Play) feature.PCI, or Peripheral Component Interconnect, is a system which allows I/O devices tooperate at speeds nearing the speed the CPU itself uses when communicating withits special components. This section covers some very technical items and it isstrongly recommended that only experienced users should make any changes to thedefault settings.

3-18

MS-7357 Mainboard

IRQ Resource SetupPress <Enter> to enter the sub-menu and the following screen appears:

IRQ 3/ 4/ 5/ 7/ 9/ 10/ 11/ 14/ 15These items specify the bus where the specified IRQ line is used.The settings determine if AMIBIOS should remove an IRQ from the pool of avail-able IRQs passed to devices that are configurable by the system BIOS. Theavailable IRQ pool is determined by reading the ESCD NVRAM. If more IRQs mustbe removed from the IRQ pool, the end user can use these settings to reservethe IRQ by assigning an [Reserved] setting to it. Onboard I/O is configured byAMIBIOS. All IRQs used by onboard I/O are configured as [Available]. If all IRQsare set to [Reserved], and IRQ 14/15 are allocated to the onboard PCI IDE, IRQ 9will still be available for PCI and PnP devices.

IRQ (Interrupt Request) lines are system resources allocated to I/O devices.When an I/O device needs to gain attention of the operating system, it signalsthis by causing an IRQ to occur. After receiving the signal, when the operat-ing system is ready, the system will interrupt itself and perform the servicerequired by the I/O device.

Important

3-19

BIOS Setup

Chassis IntrusionThe field enables or disables the feature of recording the chassis intrusion statusand issuing a warning message if the chassis is once opened. To clear the warningmessage, set the field to [Reset]. The setting of the field will automatically return to[Enabled] later.

CPU Smart FAN TargetThe mainboard provides the Smart Fan function which can control the CPU fan speedautomatically depending on the current temperature to keep it with in a specific range.You can select a fan target value here. If the current CPU fan temperature reaches tothe target value, the smart fan function will be activated. It provides several sectionsto speed up for cooling down automatically.

SYS FAN1 ControlThe field allows you to determine the fan speed whether the system fan connectedto SYSFAN1 when the system is turned on.

---- PC Health Status ----

CPU/ System Temperature, CPU FAN/ SYS FAN1 Speed, CPU Vcore, 3.3V,,5V, 12V, 5V SBThese items display the current status of all of the monitored hardware devices/components such as CPU voltage, temperatures and all fans’ speeds.

H/W Monitor

3-20

MS-7357 Mainboard

Current CPU/ DRAM FrequencyThese items show the current clocks of CPU and Memory speed. Read-only.

Intel EISTThe Enhanced Intel SpeedStep technology allows you to set the performance level ofthe microprocessor whether the computer is running on battery or AC power. Thisfield will appear after you installed the CPU which support speedstep technology.

Adjust CPU FSB FrequencyThis item allows you to select the CPU Front Side Bus clock frequency (in MHz) andoverclock the processor by adjusting the FSB clock to a higher frequency. Settingoptions: For CPU FSB200: [200]~[500]

Adjusted CPU FrequencyThis item shown the CPU frequency after you adjusted. You need to restart thesystem to load the new CPU frequency you choose. (read only)

Frequency/Voltage Control

Important

Change these settings only if you are familiar with the chipset.

3-21

BIOS Setup

Advance DRAM ConfigurationPress <Enter> to enter the sub-menu and the following screen appears:

Configure DRAM Timing by SPDSelects whether DRAM timing is controlled by the SPD (Serial Presence Detect)EEPROM on the DRAM module. Setting to [Auto By SPD] enables DRAM timingsand the following related items to be determined by BIOS based on the configu-rations on the SPD. Selecting [Manual] allows users to configure the DRAMtimings and the following related items manually.

DRAM CAS# LatencyThis controls the CAS latency, which determines the timing delay (in clock cycles)before SDRAM starts a read command after receiving it.

DRAM RAS# to CAS# DelayThis field allows you to set the number of cycles for a timing delay between theCAS and RAS strobe signals, used when DRAM is written to, read from orrefreshed. Fast speed offers faster performance while slow speed offersmore stable performance.

DRAM RAS# PrechargeThis item controls the number of cycles for Row Address Strobe (RAS) to beallowed to precharge. If insufficient time is allowed for the RAS to accumulate itscharge before DRAM refresh, refresh may be incomplete and DRAM may fail toretain data. This item applies only when synchronous DRAM is installed in thesystem.

DRAM RAS# Activate to PrecharThis setting determines the time RAS takes to read from and write to a memorycell.Setting options: [8~15 DRAM Clocks].

3-22

MS-7357 Mainboard

DRAM TRFCThis setting determines the time RFC takes to read from and write to a memorycell.

DRAM TWRMinimum time interval between end of write data burst and the start of aprechargecommand. Allows sense amplifiers to restore data to cells.

DRAM TWTRMinimum time interval between the end of write data burst and the start of acolumn-read command. It allows I/O gating to overdrive sense amplifiers beforeread com-mand starts.

DRAM TRRDWhen the Timing Mode is set to [Manual], the field is adjustable. Specifies theactive-to-active delay of different banks. Available settings: [Auto], [2T], [3T], [4T].

DRAM TRTPTime interval between a read and a precharge command.

Memory HoleIn order to improve performance, certain space in memory can be reserved forISA peripherals. This memory must be mapped into the memory space below16MB. When this area is reserved, it cannot be cached.

FSB/Memory RatioThis setting control the ratio of CPU FSB / DRAM Clock Ratio to enable the CPU &DRAM to run at different frequency combinations. Please note that the setting optionsvary according to the CPU FSB Clock preset.

Adjusted DDR Memory FrequencyThis item shown the DDR memory frequency after you adjusted. You need to restartthe system to load the new memory frequency you choose. (read only)

Adjust PCIE FrequencyThis field allows you to select the PCIE frequency (in MHz).

Auto Disable DIMM/PCI FrequencyThis item is used to auto detect the DIMM/PCI frequency. Settings: [Enabled], [Disabled].

CPU VoltageThis item allows you to increase the CPU voltage.

3-23

BIOS Setup

Memory VoltageAdjusting the memory voltage can increase the DDR speed.

VTT FSB VoltageThis item allows you to set the FSB VTT voltage.

NB VoltageAdjust the North Bridge chipset voltage.

SB I/O PowerAdjust the South Bridge I/O voltage.

SB Core PowerAdjust the South Bridge core voltage.

Spread SpectrumThis setting is used to enable or disable the Spread Spectrum feature. W henoverclocking, always set it to [Disabled].

1. If you do not have any EMI problem, leave the setting at [Disabled] for optimalsystem stability and performance. But if you are plagued by EMI, select thevalue of Spread Spectrum for EMI reduction.

2. The greater the Spread Spectrum value is, the greater the EMI is reduced, andthe system will become less stable. For the most suitable Spread Spectrumvalue, please consult your local EMI regulation.

3. Remember to disable Spread Spectrum if you are overclocking becauseeven a slight jitter can introduce a temporary boost in clock speed which mayjust cause your overclocked processor to lock up.

Important

3-24

MS-7357 Mainboard

The two options on the main menu allow users to restore all of the BIOS settings tothe default Fail-Safe or Optimized values. The Optimized Defaults are the defaultvalues set by the mainboard manufacturer specifically for optimal performance of themainboard. The Fail-Safe Defaults are the default values set by the BIOS vendor forstable system performance.

When you select Load Fail-Safe Defaults, a message as below appears:

Selecting Ok and pressing Enter loads the BIOS default values for the most stable,minimal system performance.

When you select Load Optimized Defaults, a message as below appears:

Selecting Ok and pressing Enter loads the default factory settings for optimal sys-tem performance.

Load Fail-Safe/ Optimized Defaults

3-25

BIOS Setup

BIOS Setting Password

When you select this function, a message as below will appear on the screen:

Type the password, up to six characters in length, and press <Enter>. The passwordtyped now will replace any previously set password from CMOS memory. You willbe prompted to confirm the password. Retype the password and press <Enter>. Youmay also press <Esc> to abort the selection and not enter a password.To clear a set password, just press <Enter> when you are prompted to enter thepassword. A message will show up confirming the password will be disabled. Oncethe password is disabled, the system will boot and you can enter Setup withoutentering any password.When a password has been set, you will be prompted to enter it every time you tryto enter Setup. This prevents an unauthorized person from changing any part of yoursystem configuration.

A-1

Dual Core Center

Dual Core Center

Dual CoreCenter, the most useful and powerful utilitythat MSI has spent much research and ef forts todevelop, helps users to monitor or configure the hard-ware status of MSI Mainboard & MSI Graphics card inwindows, such as CPU/GPU clock, voltage, fan speedand temperature.Before you install the Dual CoreCenter, please makesure the system has meet the following requirements:

1. Intel Pentium4 / Celeron, AMD Athlon XP/ Sempron or compatible CPU with PCI Express slot.2. 256MB system memory.3. CD-ROM drive for software installation.4. Operation system: Windows XP.5. DotNet Frame Work 2.0

Appendix A

A-2

MS-7357 Mainboard

Activating Dual Core Center

Once you have your Dual Core Center installed (locate the setup source file in thesetup CD accompanying with your mainboard, path: Utility --> MSI Utility --> DualCore Center), it will have an icon in the system tray, a short cut icon on thedesktop, and a short cut path in your “Start-up” menu. You may double-click on eachicon to enable Dual Core Center.

short-cut icon in the system tray

short-cut path in the start-up menu( p ath : S t ar t - - > P r og rams - - > MSI - - >DualCoreCenter-->DualCoreCenter)

A-3

Dual Core Center

Main

Before using this utility, we have to remind you: only when installing the MSIV044 (V044 has to install with the version 8.26 or newer driver)/ V046 orV060 graphics card can activate the full function of this utility. If you install agraphics card of other brand, only hardware status of the MSI mainboard would beavailable.

Introduction:Click each button appearing above to enter sub-menu to make further configurationor to execute the function.

M BClick MB button to read current CPU temperature, FSB and CPU clock ofmainboard will show below.

VGAClick VGA button to read current GPU temperature, GPU clock and memoryclock of graphics card will show below.

DOTClick DOT button to enable or disable the Dynamic Overclocking Technology.

A-4

MS-7357 Mainboard

AV/ Game/ Office/ Silence/ CoolMSI provides five common settings for different environments. The settingshad been set to optimal values to reach better performance in eachenvironment. Click the button you need.

ClockIn this sub-menu, you can adjust and monitor the clocks of MB and graphicscard.

VoltageIn this sub-menu, you can adjust and monitor the voltages of MB and graphicscard.

FAN SpeedIn this sub-menu, you can adjust and monitor the fan speeds of MB andgraphics card.

TemperatureIn this sub-menu, you can monitor the temperatures of MB and graphics card.

User ProfileIn this sub-menu, you can set the values of clock, voltage and fan speed byyour need and save them in a profile. You can save 3 profiles for further use.

Important

Click on the icon , the clock, voltage, fan, and temperature buttons willappear beside the icon.

Important

Before clicking the AV/ Game/ Office/ Silence or Cool button, select Smoothmode or Sharp mode to decide whether you want the system to reach theoptimal values smoothly or quickly.

Sharp mode Smooth mode

A-5

Dual Core Center

DOT (Dynamic OverClocking)

Dynamic Overclocking Technology is an automatic overclocking function, included inthe MSITM’s newly developed Dual CoreCenter Technology. It is designed to detect theloading of CPU/ GPU while running programs, and to over-clock automatically. Whenthe motherboard detects that the loading of CPU is exceed the default threshold for atime, it will speed up the CPU and fan automatically to make the system run smootherand faster. When the graphics card detects that the loading of GPU is exceed thedefault threshold for a time, it will speed up the GPU, memory, fan and voltageautomatically to make the system run smoother and faster. When the CPU/ GPU istemporarily suspending or staying in low loading balance, it will restore the defaultsettings instead. Usually the Dynamic Overclocking Technology will be powered onlywhen users' PC runs huge amount of data, like 3D games or video process, and themotherboard/ graphicd card need to be boosted up to enhance the overall performance.There will be several selections when you click the DOT rate button (include increaserate and decrease rate buttons), to select the DOT level, then you have toclick the DOT button to apply the DOT function.

Important

Even though the Dynamic Overclocking Technology is more stable thanmanual overclocking, basically, it is still risky. We suggest user to makesure that your CPU can afford to overclock regularly first. If you find the PCappears to be unstable or reboot incidentally, it's better to lower the level ofoverclocking options. By the way, if you need to conduct overclockingmanually, please do not to apply the DOT function.

DOT FSB-DOWNRate button

DOT FSB-UPRate button

A-6

MS-7357 Mainboard

Clock

In the Clock sub-menu, you can see clock status (including FSB/ CPU clock ofmainboard and GPU/ memory clock of graphics card) of your system. And you canselect desired value for overclocking. There will be several items for you to select foroverclocking after you click button. You can click the plus sign button to increase the clock, or click the minus sign button to decrease the clock. Andfinally, click the Apply button to apply the values adjusted. If you do not want to applythe adjustments, click the Cancel button to cancel. Or click the Default button torestore the default values.

On the underside, it shows the graphs of the clocks. Only the curves of the itemwhich the button is lit up with red color will be shown.

Important

In the user profile, clicking the Save button can save the changes to it. In thedefault profile, the Save button is not available.

A-7

Dual Core Center

Voltage

In the Voltage sub-menu, you can see voltage status (including Vcore, memory, GPUvoltage... etc.) of your system, and you can select desired value for overclocking. Itwill show several items to select for overclocking after you click the button.You can click the plus sign button to increase the voltage, or click the minus signbutton to decrease. And finally, click the Apply button to apply the adjustments.If you do not want to apply the adjustments, click the Cancel button to cancel. Or clickthe Default button to restore the default values.

On the underside, it shows the graphs of the voltages. Only the curves of the itemwhich the button is lit up with red color will be shown.

I

Important

In the user profile, clicking the Save button can save the changes to it. In thedefault profile, the Save button is not available.

A-8

MS-7357 Mainboard

FAN Speed

In the FAN Speed sub-menu, you can read fan status of your system. Select higherspeed for better cooling effect. There are several sections for you to change the fanspeed to a section after clicking button. Click the plus sign button toincrease the fan speed to a section, or click the minus sign button to decrease.Or click the Default button to restore the default values.

On the underside, it shows the graphs of the fan speed. Only the curves of the itemwhich the button is lit up with red color will be shown.

Important

1. When you set the fan speed manually, please make sure to disabled the “CPU Smart FAN Target” item in the BIOS.2. In the user profile, clicking the Save button can save the changes to it. In the default profile, the Save button is not available.

A-9

Dual Core Center

Temperature

In the Temperature sub-menu, you can see temperature status of your system.

On the underside, it shows the graphs of the temperatures. Only the curves of theitem which the button is lit up with red color will be shown.

A-10

MS-7357 Mainboard

User Profile

In the User Profile sub-menu, click the setting button that besides the user profilebar, and the next screen will appear.

Here you can define the clock/ fan speed/ voltage by your need, click thebutton to choose a value quickly, or click the plus / minus sign button toincrease/ decrease the value.

A-11

Dual Core Center

Use the draw bar to set the max system temperature. When the system temperatureexceeds the threshold you defined, the system will pop up a warning message andshut down the system.Use the draw bar to set the minimal fan speed. When the fan speed is lower than thethreshold you defined, the system will pop up a warning message.

Finally, you can choose the user profile by click the button in the left side and click theApply button to load the user profile.

After setting all values you need, you can change the user profile name in the boxthen click the save button to save all changes in a profile.

B-1

Realtek ALC888 Audio

Realtek ALC888 AudioAppendix B

The Realtek ALC888 provides 10-channel DAC that si-multaneously supports 7.1 sound playback and 2 chan-nels of independent s tereo sound output (multiplestreaming) through the Front-Out-Left and Front-Out-Right channels.

MS-7357 Mainboard

B-2

You need to install the driver for Realtek ALC888 codec to function properly beforeyou can get access to 2-, 4-, 6-, 8- channel or 7.1+2 channel audio operations.Follow the procedures described below to install the drivers for different operatingsystems.

Installation for Windows 2000/XPFor Windows® 2000, you must install Windows® 2000 Service Pack4 or later beforeinstalling the driver. For Windows® XP, you must install Windows® XP Service Pack1or later before installing the driver.The following illustrations are based on Windows® XP environment and could lookslightly different if you install the drivers in different operating systems.

1. Insert the application CD into the CD-ROM drive. The setup screen will auto-matically appear.

2. Click Realtek HD Audio Driver.

Installing the Realtek HD Audio Driver

Important

The HD Audio Configuration software utility is under continuous updateto enhance audio applications. Hence, the program screens shown here inthis section may be slightly different from the latest software utility and shallbe held for reference only.

Click here

B-3


3. Click Next to install the Realtek High Definition Audio Driver.

Click here

Select thisoption

4. Click Finish to restart the system.

Click here

MS-7357 Mainboard

B-4

After installing the audio driver, you are able to use the 2-, 4-, 6- or 8- channel audiofeature now. Click the audio icon from the system tray at the lower-right corner ofthe screen to activate the HD Audio Configuration. It is also available to enable theaudio driver by clicking the Azalia HD Sound Effect Manager from the ControlPanel.

Double click

Software Configuration

B-5


Sound Effect

Environment SimulationYou will be able to enjoy different sound experience by pulling down the arrow,totally 23 kinds of sound effect will be shown for selection. Realtek HD Audio SoundManager also provides five popular settings “Stone Corridor”, “Bathroom”, “Sewerpipe”, “Arena” and “Audio Corridor” for quick enjoyment.

You may choose the provided sound effects, and the equalizer will adjust automatically.If you like, you may also load an equalizer setting or make an new equalizer setting tosave as an new one by using the “Load EQ Setting” and “Save Preset” button,click “Reset EQ Setting” button to use the default value, or click “Delete EQ Set-ting” button to remove a preset EQ setting.

There are also other pre-set equalizer models for you to choose by clicking “Others”under the Equalizer part.

Here you can select a sound effect you like from the Environment list.

MS-7357 Mainboard

B-6

SaveThe settings are savedpermanently for futureuse

Reset10 bands of equalizerwould go back to the de-fault setting

Enable / DisableTo disable, you can tem-porarily s top the soundeffect without losing thesettings

LoadWhenever you would like touse preload settings, simplyclick this, the whole list willbe shown for your selection.

DeleteTo delete the pre-saved settings which are created from previous steps.

Equalizer SelectionEqualizer frees users from default settings; users may create their owned preferredsettings by utilizing this tool.

10 bands of equalizer, ranging from 100Hz to 16KHz.

B-7


Raise the key

Lower the key

Remove thehuman voice

Frequently Used Equalizer SettingRealtek recognizes the needs that you might have. By leveraging our long experienceat audio field, Realtek HD Audio Sound Manager provides you certain optimized equal-izer settings that are frequently used for your quick enjoyment.

[How to Use It]Other than the buttons “Pop” “Live” “Club” & “Rock” shown on the page, to pull downthe arrow in “Others”, you will find more optimized settings available to you.

Karaoke ModeKaraoke mode brings Karaoke fun back home. Simply using the music you usuallyplay, Karaoke mode can help you eliminate the vocal of the song or adjust the key toaccommodate your range.1.Vocal Cancellation: Single click on “Voice Cancellation”, the vocal of the song would be eliminated, while the background music is still in place, and you can be that singer!2.Key Adjustment: Using “Up / Down Arrow” to find a key which better fits your vocal range.

MS-7357 Mainboard

B-8

MixerIn the Mixer part, you may adjust the volumes of the rear and front panels individually.1. Adjust VolumeYou can adjust the volume of the speakers that you pluged in front or rear panel.

2. Multi-Stream FunctionALC888 supports an outstanding feature called Multi-Stream, which means you mayplay different audio sources simultaneously and let them output respectively from theindicated real panel or front panel. This feature is very helpful when 2 people areusing the same computer together for different purposes.

Click the button and the Mixer ToolBox menu will appear. Then check the Enableplayback multi-streaming and click OK to save the setup.

Important

You have to plug the device into the jacks on the rear and front panel firstbefore enable the multi-stream function.

Important

Before set up, please make sure the playback devices are well plugged in thejacks on the rear or front panel.

B-9


W hen you are playing the f irst audio source (for example: use W indows MediaPlayer to play DVD/VCD), the output will be played from the rear panel, which is thedefault setting.

Then you must to select the Realtek HD Audio 2nd output from the scroll listfirst, and use a different program to play the second audio source (for example: useWinamp to play MP3 files). You will find that the second audio source (MP3 music) willcome out from the Line-Out audio jack of Front Panel.

MS-7357 Mainboard

B-10

3. Playback control

Playback deviceThis function is to let you freely decide which ports tooutput the sound. And this is essential when multi-streaming playback enabled.- Realtek HD Audio Output- Realtek HD Audio 2nd Output

Tool Mute

MuteYou may choose to mute single or multiple volume controls or to completely mutesound output.

Tool- Show the following volume controlsThis is to let you freely decide which volume control items to be displayed.- Advanced controls- Enable playback multi-streamingW ith this function, you will be able to have an audio chat with your friends viaheadphone (stream 1 from front panel) while still have music (stream 2 from backpanel) in play. At any given period, you can have maximum 2 streams operatingsimultaneously.

B-11


4. Recording control

Recording device-Realtek HDA Primary input-Mic in at front panel (Green)

MuteYou may choose to mute single or multiple volume controls or to completely mutesound input.Tool- Show the following volume controlsThis is to let you freely decide which volume control items to be displayed.- Enable recording multi-streaming

Tool Mute

Important

ALC888 allows you to record the CD, Line, Mic and Stereo Mix channelssimultaneously, frees you from mixing efforts. At any given period, you maychoose 1 of the following 4 channels to record.

MS-7357 Mainboard

B-12

Audio I/OIn this tab, you can easily configure your multi-channel audio function and speakers.You can choose a desired multi-channel operation here.

a. Headphone for the common headphoneb. 2CH Speaker for Stereo-Speaker Outputc. 4CH Speaker for 4-Speaker Outputd. 6CH Speaker for 5.1-Speaker Outpute. 8CH Speaker for 7.1-Speaker Output

Speaker Configuration:

1. Plug the speakers in the corresponding jack.

2. Dialogue “connected device” will pop up for your selection. Please select thedevice you have plugged in. - If the device is being plugged into the correct jack, you will be able to find the icon beside the jack changed to the one that is same as your device. - If not correct, Realtek HD Audio Manager will guide you to plug the device into the correct jack.

B-13


Connector Settings

Click to access connector settings.

Disable front panel jack detection (option)Jack detection function only works with HD audio front panel.

Mute rear panel output when front headphone plugged in.

Enable auto popup dialogue, when device has been plugged inOnce this item checked, the dialog “Connected device” would automatically pop upwhen device plugged in.

MS-7357 Mainboard

B-14

S/PDIF (optional, for HDMI graphics card only)Short for Sony/Philips Digital Interface, a standard audio file transfer format. S/PDIFallows the transfer of digital audio signals from one device to another without havingto be converted first to an analog format. Maintaining the viability of a digital signalprevents the quality of the signal from degrading when it is converted to analog.

Output Sampling Rate 44.1KHz: This is recommend while playing CD. 48KHz: This is recommended while playing DVD or Dolby. 96KHz: This is recommended while playing DVD-Audio. 192KHz: This is recommended while playing High quality Audio.

Output Source No S/PDIF out: There will no S/PDIF out. Output digital audio source: The digital audio format (such as .wav, .mp3, .midi etc) will come out through S/PDIF-Out.

B-15


Test SpeakersYou can select the speaker by clicking it to test its functionality. The one you selectwill light up and make testing sound. If any speaker fails to make sound, then checkwhether the cable is inserted f irmly to the connector or replace the bad speakerswith good ones. Or you may click the auto test button to test the sounds ofeach speaker automatically.

Subwoofer

Front Right

Rear Right

Center

Front Left

Rear Left

Side Left

Side Right

MS-7357 Mainboard

B-16

MicrophoneIn this tab you may set the function of the microphone. Select the Noise Suppres-sion to remove the possible noise during recording, or select Acoustic EchoCancelltion to cancel the acoustic echo druing recording.

Acoustic Echo Cancelltion prevents playback sound from being recorded by mi-crophone together with your sound. For example, you might have chance to useVOIP function through Internet with your friends. The voice of your friend will comeout from speakers (playback). However, the voice of your friend might also berecorded into your microphone then go back to your friend through Internet. In thatcase, your friend will hear his /her own voice again. W ith AEC(Acoustic EchoCancellation) enabled at your side, your friend can enjoy the benefit with less echo.

B-17


3D Audio DemoIn this tab you may adjust your 3D positional audio before playing 3D audio applica-tions like gaming. You may also select different environment to choose the mostsuitable environment you like.

MS-7357 Mainboard

B-18

InformationIn this tab it provides some information about this HD Audio Configuration utility,including Audio Driver Version, DirectX Version, Audio Controller & Audio Codec. Youmay also select the language of this utility by choosing from the Language list.

Also there is a selection Show icon in system tray. Switch it on and an icon

will show in the system tray. Right-click on the icon and the Audio Accessoriesdialogue box will appear which provides several multimedia features for you to takeadvantage of.

B-19


Hardware Setup

Connecting the SpeakersWhen you have set the Multi-Channel Audio Function mode properly in the softwareutility, connect your speakers to the correct phone jacks in accordance with thesetting in software utility.

n 2-Channel Mode for Stereo-Speaker OutputRefer to the following diagram and caption for the function of each phone jack on theback panel when 2-Channel Mode is selected.

1 Line In2 Line Out (Front channels)3 MIC4 No function5 No function6 No function

3

1

2

6

4

5

4-Channel Analog Audio Output

MS-7357 Mainboard

B-20

n 4-Channel Mode for 4-Speaker Output


1 Line In2 Line Out (Front channels)3 MIC4 Line Out (Rear channels)5 No function6 No function

3

1

2

6

4

5

B-21




1 Line In2 Line Out (Front channels)3 MIC4 Line Out (Rear channels)5 Line Out (Center and Subwoofer channel)6 No function

1

2

6

4

5

3

MS-7357 Mainboard

B-22



1 Line In2 Line Out (Front channels)3 MIC4 Line Out (Rear channels)5 Line Out (Center and Subwoofer channel)6 Line Out (Side channels)

1

2

6

4

5

3

G33M Seriesstatic.highspeedbackbone.net/pdf/MSI_G33M_Series_Manual.pdf · If a problem arises with...

Documents

Transcript of G33M Seriesstatic.highspeedbackbone.net/pdf/MSI_G33M_Series_Manual.pdf · If a problem arises with...