G0000070
Transcript of G0000070
ELECTRICAL PRODUCTSPDL Electrical Products are available through electrical wholesalers New Zealand wide. Visit our website www.pdl.co.nzPDL Electrical Products are designed and engineered to ISO 9001. Freecall 0800 652 999. Freefax 0800 101 152. Email: [email protected]
PDL is a brand of Schneider Electric
Prepared for tomorrow.Designed for today.
Whit
e
Beige
Ivory
Crea
m
Switch on to NewStandards in Elegance
Polis
hed B
rass
Stain
less S
teel
Blac
k
Brus
hed B
ronz
e
The PDL 600 Designer Series is a significant
breakthrough in style and design excellence - a
perfect combination of good looks and feature-rich
practicality that brings new heights in elegance.
From the range of high quality plate finishes to the
stylish, chamfered edges, PDL’s 600 Designer Series
will blend in beautifully with any decor. The high
quality finish - unhindered by any visible screw caps -
combines the practical, non-marking advantages of a shiny,
highly polished switch plate with the fashionable,
unobtrusive appearance of a traditional matt finish.
Designed in consultation with practising electricians and
endorsed by leading architects, the PDL 600 Designer Series
is a uniquely elegant addition to today’s decor and design.
Over seventy practising electrical contractors were
involved in setting the design and feature specifications
of the PDL 600 Designer Series.
Behind the switch plates are a host of innovative time-
saving installation and safety features built into the
design. Extensive testing at an independent Telarc-
registered laboratory – equivalent to 100 years of
ordinary use – bears testimony to the superiority of
the PDL switch.
The 600 Designer Series utilises the world-leading
innovation of the front-loading 500 Series module
and is compatible with the full range of 500 and
600 Series specialty modules.
Designed and manufactured for New Zealand homes
and buildings, the 600 Designer Series is superior in
so many ways.
The Contractor’s Choice…
Clear Sub PlatesPDL sub plates in clearpolycarbonate are a feature ofone, two, and three-gangswitches. This enables clearand easy identification ofwiring configurations, as wellas simplifying the lining up offixing screws with flush boxthreads.
in at least ten waysFront-loading ModulesFront-loading switch modulescannot be pushed back into thewall cavity by frontal impact,saving low-profit maintenancecalls while maximising end-usersafety.
20 Amp Switch RatingSwitches are rated at 20 Ampsas standard.
Ratings:250V a.c., 50Hz,20A Resistive,20AX Highly Inductive,16AX Fluorescent,M60 Motor Rating,
DurableDecorating CapPDL’s clear plastic decoratingcap is stronger, more durableand better fitting than the thinblisters supplied with otherbrands. Switch can be operatedwhile the cap is held firmly inplace.
Backed-off TerminalScrewsAll 600 Designer Series switchand socket terminal screws arebacked off for immediatetermination – bigger terminalsprovide more room for cableconductors.
Ready-to-go FixingScrews & AdditionalLoop TerminalFixing screws are supplied heldin place by the decorating cap,ready to go as soon as the subplate is taken out of its bag.Additional loop terminal onsingle switches saves time andmoney.
Phillips/slotted ScrewHeadsPDL’s combination Phillips/slottedterminal and fixing screwsallow fitting and connectionsto be done faster and moreeasily. The versatile screwheads accommodate either aPhillips, Pozi or flat-bladedscrewdriver.
Clip-on Cover PlatesA range of clip-on coversconceal mounting screws andsimplify finishing anddecorating – with no visiblegap between switch moduleand cover plate.
Metal or Gloss FinishCover plates come in three highlypopular metal finishes – polishedbrass, brushed bronze andstainless steel – plus five designercolours with an elegant, glossfinish that’s easy to care for. Forcleaning, simply use a clothdampened with water only.Cleaning agents are notrecommended as their use mayharm the product and voidwarranty claims.
Removable Extra SwitchThe removable extra switch onPDL sockets allows for greaterflexibility. The extra switch can bereplaced with a 500 Series or 600Designer Series module to suityour application (excludingtelephone modules). Optionsinclude neon indicators, hinged lidmodules, push button switchmodules, etc.
4
3
6
8
9
2 7
10
1
5
2-Way.
Index Switches Page
Standard Switches 8Waterproof Switches, IP56 9 - 10Waterproof Permanent Connection Unit, IP56 10Permanent Connection Unit 10Fan Speed Control Switches 11Dimmer Switches 11Range Switches 11Programmable Time Switches 12Time Delay Switches 12Card-Operated Switches 13Key Card Operated Switch 13
Switch PlatesStandard Switch Plates 14Switch Plates with ID Facility 15Blank Plates 16Worktop Switch Plates 16Architrave Switch Plates 16
Cover PlatesSwitch Cover Plates 18Socket Cover Plates 19Dual Cover Plates 20Combination Cover Plates 20
Protected Switches & SocketsRCD Protected Sockets 21RCD Protection Devices 22RCD Protected Socket & Shaver Socket 22Universal Shaver Socket 22
Surge Protected SocketFine Surge Protection 23
Switched SocketsVertical Switched Sockets 24 - 26Horizontal Switched Sockets 27 - 29Worktop Switched Sockets 30
Unswitched SocketHorizontal, Unswitched Socket 31
Phone, Fax & TV Outlets Page
BT Telephone Jackpoints 31TV Outlet 31
Switch ModulesStandard Switch Modules 33 - 34Standard Modules with Hinged Lids 34Dedicated Switch Modules 34Illuminated Modules 35Buzzer Modules 35Rotary Switch Modules 35Tactile Switch Modules 36Dimmer Control Modules 36Fan Speed Control Modules 36Push Button Switch Modules 37Pull Cord Switch Modules 37Permanent Connection Module 37Blank Modules 38Communication Modules 38 - 40Module Shroud 41Module Ejector 41
Batten HolderBatten Holder with Clip-on Cover 41Ceiling Mounting Base 41
Additional AccessoriesHot Water Switches 42Ceiling Switches 42Time Switch 42Key Lock Switches 43Waterproof Safety Switch 43Range Switches 44Range Socket 44Automatic Lighting Sensor Switch 45Threaded Socket 45
Mounting AccessoriesFlush Boxes 46Mounting Brackets 46 - 47Module Mounting Clips 47Mounting Blocks & Spacers 48 - 49Conversion Plate 49
Floor-Mounted Accessories Page
Floor Socket 49Power Tower 49
Multi-Gang Switch PanelsStainless Steel Switch Plates 50Switch Panel Wall Boxes 50
Miscellaneous AccessoriesTerminals 51Junction Boxes 51
Focus on Risk ManagementSurge Protection 52Recessed Sockets with Safety Shrouds 52Front-loading Modules 52Waterproof Switches 53Safety Shuttered Sockets 53Safety Switches 53
Electronic Building Operating SystemsPDL e.BOS 54
Data & Communication ProductsSuperNet 55
Technical DataWiring Diagrams 56 - 59
Quality ManagementProduct Testing for Quality Assurance 60
Index by Catalogue NumberProducts in Numerical Order 62 - 63
SWITCHES
STANDARD SWITCHESSwitches comply with Standards: AS3100, AS3133 & BS3676.Ratings: 250V a.c., 50Hz, 20A Resistive, 20AX Highly Inductive,
16AX Fluorescent to EN 60669-1, M60, Motor Rating.Terminals accommmodate: 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
681
6811-GANG SWITCHPlate: 118mm x 74mmMounting centres: 84mmVertical or horizontal mounting.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 681M# Metal coverplate.
683
6833-GANG SWITCHPlate: 118mm x 74mmMounting centres: 84mmVertical or horizontal mounting.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 683M# Metal coverplate.
684H
6844-GANG SWITCHPlate: 118mm x 74mmMounting centres: 84mmVertical or horizontal mounting.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.Suits Cat 684M# Metal cover plate.
Order as 684VH and 4 x 681M20.
686H
6866-GANG SWITCHPlate: 118mm x 74mmMounting centres: 84mmVertical or horizontal mounting.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.Suits Cat 686M# Metal coverplate.
Order as 686VH and 6 x 681M20.
Page 8
682
6822-GANG SWITCHPlate: 118mm x 74mmMounting centres: 84mmVertical or horizontal mounting.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 682M# Metal coverplate.
685
6855-GANG SWITCHPlate: 118mm x 74mmMounting centres: 84mmVertical or horizontal mounting.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.Suits Cat 686M# Metal cover plate.
Order as 685VH and 5 x 681M20.
WATERPROOF SWITCHES, IP56Switches comply with Standards: AS3100, AS3133, BS3676 & AS1939.Ratings: 230V - 240V a.c., 50Hz, 16A Resistive, 16AX Inductive,
10AX Fluorescent. IP 56 Protection.Terminals accommodate: 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
Switches meet the requirements for installation in Zone 1 as perAS/NZS 3000:2000, Sections 7.1, 7.2 and 7.6, and NZS 3000: 1997,Sections 702.9.2 and 702.9.3
681HWP
681HWPHORIZONTAL 1-GANG SWITCHPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Suits Cat 681M# Metal coverplate.
682VWPD
682VWPVERTICAL 2-GANG SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 682M# Metal coverplate.
682VWPDVERTICAL 2-GANG SWITCHwith DEDICATED MODULESAs for 682VWP but withdedicated modules for light andfan.Available white only.
682HWP
682HWPHORIZONTAL 2-GANG SWITCHPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Suits Cat 682M# Metal coverplate.
683VWP
683VWPVERTICAL 3-GANG SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V MountingBracket.
Suits Cat 683WPM# Metal coverplate.
683VWPD
683VWPDVERTICAL 3-GANG SWITCHwith DEDICATED MODULESAs for 683VWP but withdedicated modules for light,fan and heat.
Available white only.
683HWP
683HWPHORIZONTAL 3-GANG SWITCHPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Suits Cat 683WPM# Metal coverplate.
681VWP
681VWPVERTICAL 1-GANG SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 681M# Metal coverplate.
Page 9
651
651PERMANENT CONNECTIONUNITPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat145V, 148V or 146V MountingBracket.
Suits Cat 682M# Metal coverplate.
PERMANENT CONNECTION UNITPCU complies with Standards: AS3100 & AS3133.Ratings: 250V a.c., 50Hz, 20A Resistive, 20AX Highly Inductive,
16AX Fluorescent, M60.Terminals accommodate: 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
651VWP
651VWPPERMANENT CONNECTIONUNIT, IP56Plate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 682M# Metal coverplate.
WATERPROOF PERMANENT CONNECTION UNIT, IP56PCU complies with Standards: AS3100, AS3133 & AS1939.Ratings: 230V - 240V a.c., 50Hz, 16A Resistive, 16AX Inductive,
10AX Fluorescent. IP 56 Protection.Terminals accommodate: 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
WATERPROOF SWITCHES, IP56 cont...
683HWPD
683HWPDHORIZONTAL 3-GANG SWITCHwith DEDICATED MODULESAs for 683HWP but withdedicated modules for light,fan and heat.
Available white only.
684VWP
684VWPVERTICAL 4-GANG SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 684M# Metal coverplate.
684VWPD
684VWPDVERTICAL 4-GANG SWITCHwith DEDICATED MODULESAs for 684VWP but withdedicated modules for light,fan and heat.
Available white only.
684HWP
684HWPHORIZONTAL 4-GANG SWITCHPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Suits Cat 684M# Metal coverplate.
684HWPDHORIZONTAL 4-GANG SWITCHwith DEDICATED MODULESAs for 684HWP but withdedicated modules for light,fan and heat.
Available white only.
Page 10
625
625FAN SPEED CONTROL SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuitable for induction andshaded pole motors.Features adjustable minimumspeed control.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 625M# Metal coverplate.
FAN SPEED CONTROL SWITCHESSwitches comply with Standard: AS3100.Ratings: 230V - 240V a.c., 50Hz.Terminals accommodate: 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
625X
Page 11
625C3 680
680VERTICAL RANGE SWITCH SP 32APlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 680M# Metal cover plate.
RANGE SWITCHESSwitches comply with Standards: AS3100 & AS3133.Ratings: SP: 230V - 240V a.c., 50Hz, 32A Resistive, 25AX Inductive, M180.
3mm contact gap. Terminals accommodate: 2 x 6mm2 cables each.DP: 400V - 415V a.c., 50Hz, 32A Resistive, 32AX Inductive.Terminals accommodate: 4 x 2.5mm2 cables each or 3 x 4mm2
cables each.
679H/2
620 & 620K
620ROTARY DIMMER SWITCHRating: 230V - 240V a.c. 50Hz.,70W - 400W. Leading Edge.Plate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 682M# Metal cover plate.
620KROTARY DIMMER SWITCHRating: 230V - 240V a.c. 50Hz.,150W - 1000W. Leading Edge.Plate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block withCat 557 Spacer (spacer included),Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 682M# Metal cover plate.
DIMMER SWITCHESDimmers comply with Standards: AS3100 & AS3133.Terminals accommodate: 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
625XFAN SPEED CONTROL withEXTRA SWITCHAs for 625 but with an extra681M20 2-Way switch module.
Suits Cat 625XM# Metal coverplate.
625C33-SPEED ‘NO HUM’ CEILINGSWEEP FAN CONTROLLERPlate: 118mm (h) x 74mm (w)Mounting centres: 84mm3-speed control for ceilingsweep fans up to 100VA.Uses 2µF and 3µF capacitors tocontrol fan speed.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 682M# Metal coverplate.
625C3/13-SPEED ‘NO HUM’ CEILINGSWEEP FAN CONTROLLERAs for 625C3 but uses 1µF and2µF capacitors to control fanspeed.
= EMC compliant. 679H/2HORIZONTAL RANGE SWITCHDP 32APlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Suits Cat 679M# Metal cover plate.
679V/2VERTICAL RANGE SWITCH DP 32APlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
679VN/2As for 679V/2 but fitted with neonto indicate ‘ON’ and available inwhite only.
NEW
632
632TIME DELAY SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmRating: 230V - 240V a.c., 50Hz,20AX resistive and inductive.Switch operates light and extractorfan together or independently.When light is turned OFF, fancontinues for 8 minutes. Comeswith both standard and ‘PRESS’switch modules.To use the fan without the light,replace Cat 681M20 module withCat 681M20P.Fan load 100VA max.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 682M# Metal cover plate.
PROGRAMMABLE TIME SWITCHESSwitches comply with Standard: AS3100.
646R24
646R24ROTARY TIMER with SHIELDPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmRating: 230V - 240V a.c., 50Hz,16AX resistive and 8AX inductive.Programmable Auto - Manual - OFF.N/C and N/O contacts.Time selection increments of20 minutes over a 24-hourperiod.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Available white only.
Suits Cat 646R24M# Metal coverplate.
646R7ROTARY TIMER with SHIELDAs for 646R24 but with timeselection increments of 140minutes over a 7-day period.
646RTCCLEAR SHIELDFor use with 646R7 and 646R24to protect settings.
646E7
646E77 DAY ELECTRONIC TIMERPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmRating: 230V - 240V a.c., 50Hz,15A resistive and 1000W tungstenhalogen. 1 x normally open and1 x normally closed contact.Built-in rechargeable back-up batteryprevents programming loss duringpower failures.7 day/ 24 hour timing facility for upto 6 different programmes withselection options including: everysingle day, weekdays, Monday toSaturday, and every day.Manual override - push ON/ push OFF.Reset button to delete all timerprogrammes. Random facility.
Suits Cat 89 Mounting Block, Cat144 Flush Box and Cat 145V,148V and 146V Mounting Bracket.
Available white only.
Suits Cat 646E7M# Metal coverplate.
648T60
648T5PRE-SET TIME DELAY SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmRating: 230V - 240V a.c., 50Hz,20A resistive.Time delay function pre-set at5 minutes.Double pole switching, normallyopen contacts.One touch activation.‘Off’ button for override of thetiming sequence – this alsoresets the timer.Accurate to +/- 6%.
Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 686M# Metal coverplate.
648T15PRE-SET TIME DELAY SWITCHAs for 648T5 but with time delayfunction pre-set at 15 minutes.Accurate to +/- 6%.
648T30PRE-SET TIME DELAY SWITCHAs for 648T5 but with time delayfunction pre-set at 30 minutes.Accurate to +/- 6%.
648T60PRE-SET TIME DELAY SWITCHAs for 648T5 but with time delayfunction pre-set at 60 minutes.Accurate to +/- 6%.
648T120PRE-SET TIME DELAY SWITCHAs for 648T5 but with time delayfunction pre-set at 120 minutesand accurate to +/- 8%.
Page 12
TIME DELAY SWITCHESSwitches comply with Standard: AS/NZS3100.
626VC2 & 626VC4
CARD-OPERATED SWITCHES
626N
626NKEY CARD OPERATED SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mm2 module switch with neonlocator and Key Card.Fitted with 2 x 681M20 2-Wayswitch modules and 2 x 500BModule Blanks.Switches can only be operated bythe Key Card which is inserted viathe bottom slot.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.Available white only.
Suits Cat 626NM# Metal cover plate.
KEY CARD OPERATED SWITCHSwitch complies with Standards: AS3100, AS3133 & BS3676.Ratings: 250V a.c., 50Hz, 20A Resistive, 20AX Highly Inductive,
16AX Fluorescent, M60.Terminals accommodate: 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
Page 13
626VC2HOSPITALITY CARD SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmRating: 230V - 240V a.c., 50Hz,2 x 16 Amp resistive circuitscontrolled by a door entry card.Provision for two extra modulesfor manually controlled circuitsor other standard modules.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 626VCM# Metal coverplate.
626VC4HOSPITALITY CARD SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmRating: 230V - 240V a.c., 50Hz,4 x 10 Amp resistive circuitscontrolled by a door entry card.Provision for two extra modulesfor manually controlled circuitsor other standard modules.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 626VCM# Metal coverplate.
Other options are available onrequest. Lead times apply.
Switches comply with Standards: AS3100, AS3133 & BS3676.
SWITCH PLATES
STANDARD SWITCH PLATES
681VH
681VH1-APERTUREPlate: 118mm x 74mmMounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 681M# Metal coverplate.
682VH
682VH2-APERTUREPlate: 118mm x 74mmMounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 682M# Metal coverplate.
683VH
683VH3-APERTUREPlate: 118mm x 74mmMounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 683M# Metal coverplate.
684VH
684VH4-APERTUREPlate: 118mm x 74mmMounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 684M# Metal coverplate.
685VH
685VH5-APERTUREPlate: 118mm x 74mmMounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 686M# Metal coverplate.
686VH
686VH6-APERTUREPlate: 118mm x 74mmMounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 686M# Metal coverplate.
Plates comply with Standard: AS3100.
Page 14
684HID
684HID4-APERTUREPlate: 74mm (h) x 118mm (w)Mounting centres: 62mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat145V, 148V, 148H 146V or146H Mounting Bracket.
Available white only.
Metal cover plate N/A.
682VID
682VID2-APERTUREPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 MountingBlock , Cat 144 Flush Box andCat 145V, 148V, 148H, 146V or146H Mounting Bracket.
Available white only.
Metal cover plate N/A.
SWITCH PLATES WITH ID FACILITYPlates comply with Standard: AS3100.
681VID
681VID1 APERTUREPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Available white only.
Metal cover plate N/A.
681HID
681HID1 APERTUREPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Available white only.
Metal cover plate N/A.
682HID
682HID2-APERTUREPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 MountingBlock, Cat 144 Flush Box andCat 145V, 148V, 148H, 146V or146H Mounting Bracket.
Available white only.
Metal cover plate N/A.
683HID
683HID3-APERTUREPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat145V, 148V, 148H, 146V or146H Mounting Bracket.
Available white only.
Metal cover plate N/A.
684VID
684VID4-APERTUREPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat145V, 148V, 148H, 146V or146H Mounting Bracket.
Available white only.
Metal cover plate N/A.
Page 15
661VH
661VH1-APERTUREPlate: 78mm x 32mmMounting centres: 62mmSuits Cat 560 Mounting Block.
Suits Cat 661M# Metal coverplate.
ARCHITRAVE SWITCH PLATESPlates comply with Standard: AS3100.
650VH
650VHBLANK PLATEPlate: 118mm x 74mmMounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.Suitable for use by OEMcustomers.
Suits Cat 686M# Metal coverplate.
BLANK PLATESPlates comply with Standard: AS3100.
650BVH
650BVHSTANDARD FULL-FACEBLANK PLATEPlate: 118mm x 74mmMounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 650BM# Metal coverplate.
688VH
688VH1-APERTUREPlate: 48mm (h) x 100mm (w)Mounting centres: 80mmSuits Cat 567S MountingBlock and Cat 558 MountingBracket.
Suits Cat 688M# Metal coverplate.
WORKTOP SWITCH PLATESPlates comply with Standard: AS3100.
689VH
689VH2-APERTUREPlate: 48mm (h) x 100mm (w)Mounting centres: 80mmSuits Cat 567S MountingBlock and Cat 558 MountingBracket.
Suits Cat 689M# Metal coverplate.
662VH
662VH2-APERTUREPlate: 78mm x 32mmMounting centres: 62mmSuits Cat 560 Mounting Block.
Suits Cat 662M# Metal coverplate.
663VH
663VH3-APERTUREPlate: 130mm x 32mmMounting centres: 114mmSuits Cat 565 Mounting Block.
Metal cover plate N/A.
664VH
664VH4-APERTUREPlate: 130mm x 32mmMounting centres: 114mmSuits Cat 565 Mounting Block.
Metal cover plate N/A.
Page 16
Page 17
ELECTRICAL PRODUCTSPDL Electrical Products are available through electrical wholesalers New Zealand wide. Visit our website www.pdl.co.nzPDL Electrical Products are designed and engineered to ISO 9001. Freecall 0800 652 999. Freefax 0800 101 152. Email: [email protected]
PDL is a brand of Schneider Electric
Designed for even more installation optionsand even easier fixing
PDL’s 600 Designer Series, with updatedswitched sockets, is a significantenhancement to an already provenrange, and the benefits are yours!
• Terminals on 600 Designer Seriesswitched sockets are now 20%bigger, allowing for quicker andeasier fixing.
• For easier stripping of cable andinsertion in the terminal area,terminals line up and arepositioned at the sameheight.
• Sockets now feature largerrockers, matching therockers on switchmodules.
• Additional mountingpoints on double,horizontal switchedsockets allow for morefixing options.
• The extra switch onPDL sockets is nowremovable for greaterflexibility. It can bereplaced with a moduleto suit your application(excluding telephonemodules). Options includehinged lid modules, neonindicators, push button switchmodules. double pole andintermediate switch modules, etc.
• We’ve even designed a socket withtwo removable extra switches - 694XX.
If you want a contractor-friendly rangedesigned for today, install PDL’s 600 Designer Series.
SWITCH COVER PLATES
625MPB625XMPB626NMPB626VCMPB646E7MPB646R24MPB650BMPB
POLISHED BRASS FINISH661MPB662MPB679MPB680MPB681MPB682MPB
683MPB683WPMPB684MPB686MPB688MPB689MPB
625MBBZ625XMBBZ626NMBBZ626VCMBBZ646E7MBBZ646R24MBBZ650BMBBZ
BRUSHED BRONZE FINISH661MBBZ662MBBZ679MBBZ680MBBZ681MBBZ682MBBZ
683MBBZ683WPMBBZ684MBBZ686MBBZ688MBBZ689MBBZ
625C625XC626NC626VCC646E7C646R24C650BC
PLASTIC FINISH
661C662C663C664C679C681C682C
683C683WPC684C686C688C689C
625MSS625XMSS626NMSS626VCMSS646E7MSS646R24MSS650BMSS
STAINLESS STEEL FINISH661MSS662MSS679MSS680MSS681MSS682MSS
683MSS683WPMSS684MSS686MSS688MSS689MSS
(Available white only)
Security screwed metal switch cover plates are available from PDLCustomer Services, Christchurch.
Page 18
681MPB
681MBBZ
681MSSSwitch cover plates can be used vertically or horizontally.
625MPB
625MSS625MBBZ
625C
625XMPB
625XMSS625XMBBZ
625XC
626NMPB
626NMSS626NMBBZ
626NC
626VCMPB
626VCMSS626VCMBBZ
626VCC 646E7C
646E7MPB646E7MBBZ
646E7MSS
646R24C
646R24MPB646R24MBBZ646R24MSS 650BMSS
650BMPB650BMBBZ
650BC
661MSS
661MPB661MBBZ
661C662MSS
662MPB662MBBZ
662C
663C 664C
688MSS
688MPB688MBBZ
688C689MSS
689MPB689MBBZ
689C
679MPB
679MSS679MBBZ
679C681MSS
681MPB681MBBZ
681C682MSS
682MPB682MBBZ
682C
683MSS
683MPB683MBBZ
683C
683WPMSS
683WPMPB683WPMBBZ
683WPC
684MSS
684MPB684MBBZ
684C686MSS
686MPB686MBBZ
686C
680MPB
680MSS680MBBZ
692MPB
692MSS692MBBZ
692C
691ZC 692ZC 694ZC 695ZC644ZC
691MPB
691MSS691MBBZ
691C
694C694MSS
694MPB694MBBZ
695MBBZ695MPB
695MSS695C
699C
694XXC
691RCDC
691RCDMPB
691RCDMSS691RCDMBBZ
691XMPB
691XMSS691XMBBZ
691XC
692XMPB
692XMSS692XMBBZ
692XC
695RCDMBBZ695RCDMPB
695RCDMSS695XMBBZ
695XMPB
695XMSS695XC
698MBBZ698MPB
698MSS698C
699TBMBBZ699TBMPB
699TBMSS699TBC
644C641C
694XMBBZ694XMPB
694XMSS694XC
694XXMBBZ694XXMPB
694XXMSS
SOCKET COVER PLATES
POLISHED BRASS FINISH612MPB691MPB691RCDMPB691XMPB
692MPB692XMPB694MPB694XMPB694XXMPB
695MPB695RCDMPB695XMPB698MPB699TBMPB
BRUSHED BRONZE FINISH612MBBZ691MBBZ691RCDMBBZ691XMBBZ
692MBBZ692XMBBZ694MBBZ694XMBBZ694XXMBBZ
695MBBZ695RCDMBBZ695XMBBZ698MBBZ699TBMBBZ
PLASTIC FINISH
612C641C644C644ZC691C691RCDC691XC691ZC
692C692XC692ZC694C694XC694XXC694ZC
695C695XC695ZC698C699C699TBC
STAINLESS STEEL FINISH612MSS691MSS691RCDMSS691XMSS
692MSS692XMSS694MSS694XMSS694XXMSS
695MSS695RCDMSS695XMSS698MSS699TBMSS
(Available white only)
Security screwed metal socket cover plates are available fromPDL Customer Services, Christchurch.
Page 19
Shrouded socket cover plates are supplied with security screws andspecial drill bits to allow for retrofitting of the sockets.
691MSS
691MPB
691MBBZ
683-692CCOMBINATION COVER for THREE MODULES & CAT 692 SOCKETPlate: 118mm (h) x 145mm (w)Available white only. Suits Cat 149 Flush Box.
681-695CCOMBINATION COVER for SINGLE MODULE & CAT 695 SOCKETPlate: 145mm (h) x 118mm (w)Available white only. Suits Cat 149 Flush Box.
682-681CCOMBINATION COVER for TWO MODULES & SINGLE MODULEPlate: 118mm (h) x 145mm (w)Available white only. Suits Cat 149 Flush Box.
692-681CCOMBINATION COVER for CAT 692 SOCKET & SINGLE MODULEPlate: 118mm (h) x 145mm (w)Available white only. Suits Cat 149 Flush Box.
695-695XCCOMBINATION COVER for CAT 695 SOCKET & CAT 695X SOCKETPlate: 145mm (h) x 118mm (w)Available white only. Suits Cat 149 Flush Box.
Other combination cover plates are available on request.
COMBINATION COVER PLATES
683-692C
DUAL & COMBINATION COVER PLATES
DUAL COVER PLATES
Page 20
692-692CDUAL COVER for CAT 692 SOCKETSPlate: 118mm (h) x 145mm (w)Available white only. Suits Cat 149 Flush Box.
683-683CDUAL COVER for CAT 683 SWITCHESPlate: 118mm (h) x 145mm (w)Available white only. Suits Cat 149 Flush Box.
686-686CDUAL COVER for CAT 686 SWITCHESPlate: 118mm (h) x 145mm (w)Available white only. Suits Cat 149 Flush Box.
695-695CDUAL COVER for CAT 695 SOCKETSPlate: 145mm (h) x 118mm (w)Available white only. Suits Cat 149 Flush Box.
684-684CDUAL COVER for CAT 684 SWITCHESPlate: 118mm (h) x 145mm (w)Available white only. Suits Cat 149 Flush Box.
Other dual cover plate combinations are available on request.
692-692C
Page 21
RCD PROTECTED SOCKETSRCDs comply with Standards: AS3100, AS3133, AS3112 & AS3190.Rating: 230V - 240V a.c., 50Hz, 10A outlet, 20A rated.Can be connected for downstream socket protection.
691RCD-30
691RCD-30SINGLE SWITCHED SOCKET 10Awith 30mA RCD PROTECTIONPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block, Cat144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.30mA tripping current.30ms tripping time.
Available white and black only.
Suits Cat 691RCDM# Metal coverplate.
695RCD-30
695RCD-10DOUBLE SWITCHED SOCKET 10Awith 10mA RCD PROTECTIONPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.10mA tripping current.30ms tripping time.Available white only.Suits Cat 695RCDM# Metal coverplate.
695RCD-30DOUBLE SWITCHED SOCKET 10Awith 30mA RCD PROTECTIONAs for 695RCD-10 but with 30mAtripping current
.
PROTECTED SWITCHES & SOCKETS
NEW
SHAVER SOCKETSocket complies with Standards: AS3100 & AS3194.Ratings: 230V - 240V a.c., 50Hz primary; 240V or 115V a.c. secondary,
20VA max rated.
675
675UNIVERSAL SHAVER SOCKETPlate: 118mm x 74mmMounting centres: 84mmDouble insulated.Switches on when plug is inserted.Vertical or horizontal mounting.Suits Cat 89 Mounting Block withCat 557 Spacer (spacer included),Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.
Suits Cat 686M# Metal cover plate.
RCD PROTECTED SOCKET & SHAVER SOCKET
675HRCD-30
675HRCD-30RCD PROTECTED SOCKET &SHAVER SOCKETPlate: 118mm (h) x 145mm (w)Mounting centres: 84mmRCD Protected Socket andUniversal Shaver Socket on oneplate. Comes complete withCat 149 Flush Box.Available white only.Metal cover plate N/A.
RCD Protected SocketRating: 230V - 240V a.c., 50Hz.Rated Current: 10A Socket OutletComplies with Standards: AS3100,AS3190, AS3133 & AS3112.30mA tripping current.30ms tripping time.Provides RCD protection to allsockets wired downstream ofthe RCD unit.
Universal Shaver SocketRating: 230V - 240V a.c. primaryand 240V - 115V a.c. secondary,20VA max. Double insulated.Switches on when plug is inserted.Complies with Standards:AS3100 & AS3194.
RCD PROTECTION DEVICES
696RCD-10
696RCD-10PLATE MOUNTED RCD 20Awith 10mA RCD PROTECTIONPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmProtects all socket outlets orpermanently-wired appliancesdownstream.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146H or 146VMounting Bracket.10mA tripping current.30ms tripping time.
Contacts remain closed in loss ofvoltage situations.
Double pole switching protectsthe appliance user against anearth fault even in the situationwhere Active and Neutral havebeen reversed.
Available white only.
Suits Cat 686M# Metal coverplate.
696RCD-30PLATE MOUNTED RCD 20Awith 30mA RCD PROTECTIONAs for 696RCD-10 but with 30mAtripping current.
RCDs comply with Standards: AS3100, AS3133 & AS3190.Rating: 230V - 240V a.c., 50Hz, 20A rated.Can be connected for downstream socket protection.
Page 22
Page 23
695SP
695SPSURGE PROTECTED SWITCHEDSOCKETPlate: 74mm (h) x 118mm (w)Protects all socket outlets orpermanently wired appliancesboth upstream and downstreamon the same circuit.Double pole switching. Surgeprotection status is clearlyindicated by both visual andaudible means.
Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Available white only.
Metal cover plate N/A.
For added protection, PDLrecommends that medium surgeprotection (Merlin Gerin Cat16600 and Cat 16604) is fitted tothe switchboard.
600SPM
600SPMREPLACEMENT MODULEFOR 695SPFront fitting moduleallowing for easy and safereplacement.
Response time <25nS.
Available white only.
Surge protected socket complies with standards: AS/NZS3112 and AS/NZ3100.Can be connected for upstream and downstream socket protectionRatings: 230V - 240V a.c, 50Hz, Nominal clamp voltage 710V @ 50Hz.
FINE SURGE PROTECTION
SURGE PROTECTED SOCKET
NEWNEW
691/15
691/15SINGLE SWITCHED SOCKET 15APlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Available white only.
Suits Cat 691M# Metal coverplate.
692
692DOUBLE SWITCHED SOCKET 10APlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 692M# Metal coverplate.
SWITCHED SOCKETS
VERTICAL SWITCHED SOCKETS
691
691SINGLE SWITCHED SOCKET 10APlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 691M# Metal coverplate.
691Z
691ZSINGLE SWITCHED SOCKET 10Awith SAFETY SHROUDPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSecurity screws supplied –Size 0 square drive head.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Available white only.
Metal cover plate N/A.
691R
691RSINGLE SWITCHED SOCKET 10Awith ROUND EARTH PINAs for 691 but with round earthpin for dedicated circuit.Plate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Available white only.
Suits Cat 691M# Metal coverplate.
Switched sockets comply with Standards: AS3100, AS3133 & AS3112.Ratings: 230V - 240V a.c., 50Hz.For additional safety, all PDL 600 Designer Series sockets are fitted withsafety shutters behind the pin holes.
Page 24
691X
691XSINGLE SWITCHED SOCKET 10Awith REMOVABLE EXTRASWITCH 20APlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Available white only.
Suits Cat 691XM# Metal coverplate.
VERTICAL SWITCHED SOCKETS cont...
692X
692XDOUBLE SWITCHED SOCKET 10Awith REMOVABLE EXTRASWITCH 20APlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Suits Cat 692XM# Metal coverplate.
692P
692PDOUBLE SWITCHED SOCKET 10Awith ‘RCD ON’ INDICATORPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.AMBER glowing ‘RCD ON’indicator.
Available in White only.
Suits Cat 692XM# Metal coverplate.
692R
692RDOUBLE SWITCHED SOCKET 10Awith ROUND EARTH PINAs for 692 but with round earthpin for dedicated circuit.Plate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Available white only.
Suits Cat 692M# Metal coverplate.
Page 25
692ID
692IDDOUBLE SWITCHED SOCKET 10Awith CIRCUIT IDENTIFICATIONAs for 692 but with circuitidentification. An opaque cap(supplied) can be engravedbefore clipping onto the subplate. Alternatively, a label canbe printed and covered with atransparent cap (cap supplied).
Available white only.
Suits Cat 692XM# Metal coverplate.
692Z
692ZDOUBLE SWITCHED SOCKET 10Awith SAFETY SHROUDPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSecurity screws supplied –Size 0 square drive head.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Metal cover plate N/A.
692/15
692/15DOUBLE SWITCHED SOCKET 15APlate: 118mm (h) x 74mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Available white only.
Suits Cat 692M# Metal coverplate.
692N
692NAs for 692 but fitted with neon toindicate ‘ON’, and available whiteonly.
641/15
641/154-WAY SWITCHED SOCKETwith 10A and 15A OUTLETSPlate: 194mm (h) x 81mm (w)Mounting centres: 84mm3 x 10A socket outlets and1 x 15A socket outlet.Suits Cat 144 Flush Box andCat 148V or 146V MountingBracket and Cat 640RC and Cat640SC 4 Gang Mounting Block.
Available white only.
Metal cover plate N/A.
VERTICAL SWITCHED SOCKETS cont...
641
6414-WAY SWITCHED SOCKET 10APlate: 194mm (h) x 81mm (w)Mounting centres: 84mm4 x 10A socket outlets.Suits Cat 144 Flush Box andCat 148V or 146V MountingBracket and Cat 640RC and640SC 4 Gang Mounting Block.
Metal cover plate N/A.
Page 26
641N
641NAs for 641 but fitted with neonto indicate ‘ON’, and availablewhite only.
641P
641P4-WAY SWITCHED SOCKET10A with ‘RCD ON’ INDICATORPlate: 194mm (h) x 81mm (w)Mounting centres: 84mm4 x 10A socket outlets.Suits Cat 144 Flush Box andCat 148V or 146V MountingBracket and Cat 640RC and Cat640SC 4 Gang Mounting Block.
Available white only
Metal cover plate N/A.
HORIZONTAL SWITCHED SOCKETSSwitched sockets comply with Standards: AS3100, AS3133 & AS3112.Ratings: 230V - 240V a.c., 50Hz.
694
694SINGLE SWITCHED SOCKET 10APlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Suits Cat 694M# Metal coverplate.
694N
694NAs for 694 but fitted with neon toindicate ‘ON’, and available whiteonly.
Available white only.
694XX
694XXSINGLE SWITCHED SOCKET 10Awith 2 REMOVABLE EXTRASWITCHES 20APlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Available white only.
Suits Cat 694XXM# Metal coverplate.
694Z
694ZSINGLE SWITCHED SOCKET 10Awith SAFETY SHROUDPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSecurity screws supplied –Size 0 square drive head.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Avialable white only.
Metal cover plate N/A.
Page 27
694/15
694/15SINGLE SWITCHED SOCKET 15APlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Available white only.
Suits Cat 694M# Metal coverplate.
694R
694RSINGLE SWITCHED SOCKET 10Awith ROUND EARTH PINAs for 694 but with round earthpin for dedicated circuit.Plate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Available white only.
Suits Cat 694M# Metal coverplate.
694X
694XSINGLE SWITCHED SOCKET 10Awith REMOVABLE EXTRASWITCH 20APlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Available white only.
Suits Cat 694XM# Metal coverplate.
NEW
Cat 695P switched socket pictured above features an ‘RCD ON’ indicator,showing earth leakage protection status for the circuit.
HORIZONTAL SWITCHED SOCKETS cont...
695Z
695ZDOUBLE SWITCHED SOCKET 10Awith SAFETY SHROUDPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSecurity screws supplied –Size 0 square drive head.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Metal cover plate N/A.
695ID
695IDDOUBLE SWITCHED SOCKET 10Awith CIRCUIT IDENTIFICATIONAs for 695 but with circuitidentification. An opaque cap(supplied) can be engravedbefore clipping onto the subplate. Alternatively, a label canbe printed and covered with atransparent cap (cap supplied).
Available white only.
Suits Cat 695XM# Metal coverplate.
Page 28
695
695DOUBLE SWITCHED SOCKET 10APlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Suits Cat 695M# Metal coverplate.
695NAs for 695 but fitted with neonto indicate ‘ON’.Available white only.
695X
695XDOUBLE SWITCHED SOCKET 10Awith REMOVABLE EXTRASWITCH 20APlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Suits Cat 695XM# Metal coverplate.
695P
695PDOUBLE SWITCHED SOCKET 10Awith ‘RCD ON’ INDICATORPlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.AMBER glowing ‘RCD ON’indicator.
Available white only.
Suits Cat 695XM# Metal coverplate.
695R
695RDOUBLE SWITCHED SOCKET 10Awith ROUND EARTH PINAs for 695 but with round earthpin for dedicated circuit.Plate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Avilable white only.
Suits Cat 695M# Metal coverplate.
695/15
695/15DOUBLE SWITCHED SOCKET 15APlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSuits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 148Hor 146H Mounting Bracket.
Available white only.
Suits Cat 695M# Metal coverplate.
HORIZONTAL SWITCHED SOCKETS cont...
644
6444-WAY SWITCHED SOCKET 10APlate: 79mm (h) x 191mm (w)Mounting centres: 84mm4 x 10A socket outlets.Suits Cat 144 Flush Box andCat 148H or 146H MountingBracket and Cat 640RC and640SC 4 Gang Mounting Block.
Metal cover plate N/A.
644N
644NAs for 644 but fitted with neonto indicate ‘ON’.
Page 29
644/15
644/154-WAY SWITCHED SOCKETwith 10A and 15A OUTLETSPlate: 79mm (h) x 191mm (w)Mounting centres: 84mm3 x 10A socket outlets and1 x 15A socket outlet.Suits Cat 144 Flush Box andCat 148H or 146H MountingBracket and Cat 640RC and640SC 4 Gang Mounting Block.
Available white only.
Metal cover plate N/A.
644Z
644Z4-WAY SWITCHED SOCKET 10Awith SAFETY SHROUDSPlate: 79mm (h) x 191mm (w)Mounting centres: 84mm4 x 10A socket outlets.Security screws supplied –Size 0 square drive head.Suits Cat 144 Flush Box andCat 148H or 146H MountingBracket and Cat 640RC and640SC 4 Gang Mounting Block.
Available white only.
Metal cover plate N/A.
WORKTOP SWITCHED SOCKETSSwitched sockets comply with Standards: AS3100, AS3133 & AS3112.Ratings: 230V - 240V a.c., 50Hz.
698
698SINGLE SWITCHED SOCKET 10APlate: 48mm (h) x 100mm (w)Mounting centres: 80mmSuits Cat 567S Mounting Blockand Cat 558 Mounting Bracket.
Suits Cat 698M# Metal coverplate.
698NAs for 698 but fitted with neon toindicate ‘ON’.
698/15
698/15SINGLE SWITCHED SOCKET 15APlate: 48mm (h) x 100mm (w)Mounting centres: 80mmSuits Cat 567S Mounting Blockand Cat 558 Mounting Bracket.
Suits Cat 698M# Metal coverplate.
698R
698RSINGLE SWITCHED SOCKET 10Awith ROUND EARTH PINAs for 698 but with round earthpin for dedicated circuit.
Suits Cat 698M# Metal coverplate.
699TB
699TBDOUBLE SWITCHED SOCKET 10Awith SEPARATE BASESPlate 48mm (h) x 170mm (w)Mounting centres: 150mmSuits Cat 567L Mounting Blockand Cat 559 Mounting Bracket.
Suits Cat 699TBM# Metal coverplate.
699TBNAs for 699TB but fitted withneon to indicate ‘ON’.
699TB/15
699TB/15DOUBLE SWITCHED SOCKET 15APlate: 48mm (h) x 170mm (w)Mounting centres: 150mmSuits Cat 567L Mounting Blockand Cat 559 Mounting Bracket.
Available white only.
Suits Cat 699TBM# Metal coverplate.
699TBR
699TBRDOUBLE SWITCHED SOCKET 10Awith ROUND EARTH PINAs for 699TB but with roundearth pin for dedicated circuit.
Available white only.
Suits Cat 699TBM# Metal coverplate.
Page 30
699
699DOUBLE SWITCHED SOCKET 10APlate: 48mm (h) x 170mm (w)Mounting centres: 150mmSingle piece base for simplertermination.
Suits Cat 567L Mounting Blockand Cat 559 Mounting Bracket.
Metal cover plate N/A.
Page 31
BT TELEPHONE JACKPOINTS
617BT2
617BT22-WIRE BT SINGLE TELEPHONEOUTLET PLATEPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmStandard 2-wire telephoneoutlet. IDC termination.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V or 146V Mounting Bracket.
Available white only.Suits 612M# Metal cover plate.
Approved to TelepermitPTC 223/96/002.
617BT2/2
617BT2/22-WIRE BT DOUBLE TELEPHONEOUTLET PLATEPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmTwin 2-wire telephone outlet,allowing two separate lines ortwo outlets from one line.IDC termination. Suits Cat 89Mounting Block, Cat 144 FlushBox and Cat 145V, 148V or 146VMounting Bracket.
Available white only.
Suits 612M# Metal cover plate.
Approved to TelepermitPTC 223/97/003.
TV OUTLET
628 & 628F
628TV OUTLETPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmPAL type socket with clampterminals.Rating: 75 Ohm.Suits Cat 89 Mounting Block,Cat 144 Flush Box and Cat 145V,148V, 148H, 146V or 146HMounting Bracket.Suits Cat 681M# Metal coverplate.
628FTV OUTLETAs for 628 but PAL type socketwith ‘F’ connect facility in rear.
UNSWITCHED SOCKET
693/2
693/2DOUBLE HORIZONTALUNSWITCHED SOCKET 10APlate: 74mm (h) x 118mm (w)Mounting centres: 84mmSeparate bases allow forindividual circuit control ofappliances such as dishwashersand waste disposal units.Suits Cat 144 Flush Box andCat 148H or 146H MountingBracket.
Available white only.
Metal cover plate N/A.
Socket complies with Standards: AS3100 & AS3112.Rating: 230V - 240V a.c., 50Hz.
HORIZONTAL UNSWITCHED SOCKET
PHONE, FAX & TV OUTLETS
TELEPERMITA P P R O V E D
TELEPERMITA P P R O V E D
Page 32
ELECTRICAL PRODUCTSPDL Electrical Products are available through electrical wholesalers New Zealand wide. Visit our website www.pdl.co.nzPDL Electrical Products are designed and engineered to ISO 9001. Freecall 0800 652 999. Freefax 0800 101 152. Email: [email protected]
PDL is a brand of Schneider Electric
Switch mech breakthrough!There’s a tough newmech in town
Switch more applications thanever possible before with thebreakthrough single, standardsize 20 amp mech.
The new 681M20 switch modulebrings an unprecedented 20amp load to the standardmech. Now the stylish looksof the PDL 600 DesignerSeries can hide a powerfulnew functionality withobvious benefits forspecifiers and electricalcontractors.
The new 681M20 mechcan handle some veryimpressive loads:
• 20A resistive
• 20AX highly inductive
• 16AX fluorescent
• M60
Features
• Wider, deeper terminalsfor faster, easier termination
• Clearly marked shroudedterminals for increased safety,faster installation
• Terminal screws are acombination Phillips No 2/slottedheads, also backed off, for faster installationallowing for all common driver types.
Page 33
681M20P
681M20PNORMALLY OPEN SWITCHMODULERatings: 250V a.c., 50Hz, 20A.Spring return, 2-Way.Rocker marked ‘PRESS’.
681M20BAs for 681M20P but rockermarked with ‘BELL’ symbol.
681M20RAs for 681M20P but rockermarked ‘RESET’.
680M20N
680M20NNEON SWITCH MODULERatings: 250V a.c., 50Hz, 20A.1-Way.Neon flying leads can beconnected ‘permanently on’ orcan be connected to indicatewhen the switch is ‘on’ or ‘off’.
681M20HWS
681M20HWSHOT WATER SWITCH MODULERatings: 250V a.c., 50Hz,20A Resistive rating only forhot water system. 2-Way.Rocker marked ‘HWS’.
Available white only.
SWITCH MODULES
STANDARD SWITCH MODULESTerminals accommodate: 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.The terminals of Cat 680M32# can also accommodate up to 2 x 6mm2 cables each.
681M20
681M20SWITCH MODULERatings: 250V a.c., 50Hz,
20A Resistive,20AX Highly Inductive,16AX Fluorescent,M60, 2-Way.
578M16
578M16INTERMEDIATE SWITCHMODULERatings: 230V - 240V a.c., 50Hz,
16A Resistive,8AX Fluorescent and16AX Inductive.
587M10
587M10DOUBLE POLE SWITCHMODULERatings: 230V - 240V a.c., 50Hz,
10A Resistive and10AX Inductive.
NEWNEW
NEW
NEW
Page 34
681M20AC
DEDICATED SWITCH MODULESSTANDARD SWITCH MODULES cont...
680M32
SWITCH MODULES with HINGED LIDS
581M16HFCL
581M16HFRatings: 230-240V a.c., 50Hz,16A resistive,16AX inductive,10AX fluorescent, 2-Way.
581M16HFALAs for 581M16HF but withhinged, protective lid marked‘ALARM’.
581M16HFCLAs for 581M16HF but availablewhite only with clear, hinged,protective lid.Card supplied for ID purposes.
581M16HFFAs for 581M16HF but withhinged, protective lid marked‘FRIDGE’.
581M16HFMWAs for 581M16HF but withhinged, protective lid marked‘MICROWAVE’.
581M16HFSEAs for 581M16HF but withhinged, protective lid marked‘SENSOR’.581M16HFSE
681M20LO
Ratings: 250V a.c., 50Hz,20A Resistive,20AX Highly Inductive,16AX Fluorescent,M60, 2-Way.
681M20ACMarked ‘AIR CON’.
681M20A/MMarked ‘AUTO/MANUAL’.
681M20DMarked ‘DINING’.
681M20DRMarked ‘DOOR’.
681M20DWMarked ‘DISHWASHER’.
681M20DYMarked ‘DRYER’.
681M20FMarked ‘FAN’.
681M20FGMarked ‘FRIDGE’.
681M20F/RMarked ‘FORWARD/REVERSE’.
681M20GMarked ‘GAS’.
681M20GNMarked ‘GARDEN’.
681M20HMarked ‘HEAT’.
681M20HDMarked ‘HOOD’.
681M20HLFMarked ‘HIGH/FAN/LOW’.
681M20I/OMarked ‘ON/OFF’.
681M20LMarked ‘LIGHT’.
681M20LOMarked ‘LOUNGE’.
681M20MRMarked ‘MIRROR’.
681M20MWMarked ‘MICROWAVE’.
681M20OMarked ‘OUTSIDE’.
681M20PLMarked ‘POOL’.
681M20PUMarked ‘PUMP’.
681M20SMarked ‘SPA’.
681M20SEMarked ‘SENSOR’.
681M20STMarked ‘STAIRS’.
681M20TVMarked ‘TV’.
681M20WHMarked ‘WASH’.
681M20WTMarked ‘WASTE’.
680M32SWITCH MODULERatings: 230V - 240V a.c.,50Hz., Single Pole, 1-Way,32A Resistive, 25AX Inductive,M180.3mm contact gap.Terminals accommodate2 x 6mm2 conductors.
680M32ACMarked ‘AIR CON’.
680M32HMarked ‘HOB’.
680M32I/OMarked ‘ON/OFF’.
680M32OMarked ‘OVEN’.
680M32RMarked ‘RANGE’.
681M20WT
681M20L
Terminals accommodate: 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
32A
Page 35
566MNCB
566MNCBPIEZO BUZZERRating: 24V d.c.Current draw: 20mA.Sound level: 90dB.Nominal frequency: 3100 Hz.Rated for continuous use.
Module available white only.
666TMB24
BUZZER MODULES
687M4
687M33-POSITION ROTARY MODULE0, 1, 2
687M3A/M3-POSITION ROTARY MODULEAUTO, OFF, MAN
687M3I/II3-POSITION ROTARY MODULEI, 0, II
687M44-POSITION ROTARY MODULE0, 1, 2, 3
687M4F4-POSITION ROTARY MODULE0, 1, 2, 3Dial marked ‘Fan’.
ROTARY SWITCH MODULESTerminals accommodate 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
Rating: 230V - 240V a.c., 50Hz, 16A.
1588M
1588MBUZZER MODULERating: 240V a.c., 50Hz.Terminal connection: flyingleads.Sound level 70dB.
Available in White only.
666TMB24PIEZO BUZZERRating: 24V d.c.Current draw: 20mA.Sound level: 90dB.Nominal frequency: 3100 Hz.Rated for continuous use.Terminals accommodate0.5mm2 single strand cables or1mm2 multi-strand cables.
Available in White only.
666TML24
666TML24ILLUMINATED MODULERating: 24V d.c.Current draw: 20mARed LED illumination visible fromany angle.Terminals accommodate0.5mm2 single strand cables or1mm2 multi-strand cables.
Module available white only.
610TML24
610TML24ILLUMINATED MODULERating: 24V d.c.Current draw: 20mA.Red pinpoint LED illumination.Terminals accommodate0.5mm2 single strand cables or1mm2 multi-strand cables.
Module available white only.
510MN
510MNILLUMINATED MODULERating: 230V - 240V a.c., 50Hz.Two terminals for directconnection to neon.Available with CLEAR, RED, GREEN,AMBER or BLUE coloured lens.Dedicated Option: Printed ‘RCDON’ and available in white onlywith AMBER lens.
510ML12ILLUMINATED MODULERating: 12V a.c./d.c.Available with CLEAR, RED, GREEN,AMBER or BLUE coloured lens.
Module available white only.
510ML24ILLUMINATED MODULERating: 24V a.c./d.c.Available with CLEAR, RED, GREEN,AMBER or BLUE coloured lens.
Module available white only.
510MLD24V
510MLD24ILLUMINATED MODULEDEEP LENSRating: 24V a.c./d.c.Available with RED, GREEN,AMBER, BLUE or CLEARcoloured lens.
Module available white only.
ILLUMINATED MODULES
Page 36
680TMPB
680TMPBTACTILE SWITCH MODULERating: 24V d.c., 10mA.
12V d.c., 50mA.Momentary contact switch,normally open.
680TMNPB
680TMNPBILLUMINATED TACTILESWITCH MODULERating: 24V d.c., 10mA.
12V d.c., 50mA.Momentary contact switch,normally open.Separate terminals allowindependent wiring of LED.Available with RED or GREENLED.
Module available white only.
TACTILE SWITCH MODULES
520M
520MROTARY DIMMER MODULERating: 230V - 240V a.c., 50Hz,400W max.Leading Edge.Incandescent loads only.
DIMMER CONTROL MODULESTerminals accommodate 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
521M
521MREMOTE CONTROL POT2-wire remote dimmingpotentiometer.Rating of pot 470K Ohm.
Module available white only.
Terminals accommodate 0.5mm2 single strand or 1mm2 multi-strand cables.
FAN SPEED CONTROL MODULESTerminals accommodate 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
625C3M
625C3M3 SPEED ‘NO HUM’ CEILINGSWEEP FAN CONTROL MODULE3 speed control for ceilingsweep fans up to 100VA.Uses 2µF and 3µF capacitorsto control fan speed.The module is a two part unitrequiring two module spaces.
625C3/1M3 SPEED ‘NO HUM’ CEILINGSWEEP FAN CONTROL MODULE3 speed control for ceilingsweep fans up to 100VA.Uses 1µF and 2µF capacitorsto control fan speed.The module is a two part unitrequiring two module spaces.
Page 37
581M16PS
581M16PSPULL CORD SWITCH MODULERating: 230V - 240V a.c., 50Hz,
16A Resistive,10AX Fluorescent and16A Inductive.1-Way/2-Way.
Module available white only.
PULL CORD SWITCH MODULESTerminals accommodate 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
581M16PBPPROTRUDING PUSH BUTTONMODULEN/O-N/C.Ratings to AS1431 Pt. 1.Insulation Voltage 500V a.c.Operational Voltage 230V - 240V a.c.,50Hz.Thermal Current 16A.Operational Current 4A. 240V a.c.Operational Current 2A. 415V a.c.Utilisation Category AC 11.Degree of Protection IP40.Available with RED, WHITE orYELLOW button.
581M16PBS
581M16PBM
581M16PBMMUSHROOM PUSH BUTTONMODULEN/O-N/C.As for 581M16PBP butavailable with RED, WHITE orGREEN button.
PUSH BUTTON SWITCH MODULESTerminals accommodate 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
581M16PBSSHROUDED PUSH BUTTONMODULEN/O-N/C.As for 581M16PBP butavailable with RED, WHITE,GREEN or BLACK button.
581M16PBP
580M16NPS
580M16NPSPULL CORD SWITCH MODULEWITH NEONRating: 230V - 240V a.c., 50Hz,16A. 1-Way.White module with outer bodyred transparent.Neon flying leads can beconnected ‘permanently on’ orcan be connected to indicatewhen the switch is ‘on’ or ‘off’.
573MM
573MMMOMENTARY CONTACTPULL CORD SWITCH MODULERating: 24V, 12A.N/O - N/C.White module with red buttonand actuator.
551M2
551M2PERMANENT CONNECTIONMODULERating: 230V - 240V a.c.,50Hz, 16A.‘Bell Mouth’ cable entryaccommodates flexible cordsup to 10mm diameter.
PERMANENT CONNECTION MODULETerminals accommodate 4 x 1.5mm2 cables each or 2 x 2.5mm2 cables each.
Page 38
619MD
619MDDATAPLUS CAT 5 RJ45 MODULEIDC connections.Data and voice connection.Compliant to category 5, EIA-568.Allows for both 568A and 568Bwiring options.
Available in white or black only.
500B
500BBLANK MODULE
500BSTMarked ‘START’.Module available white only.
500BSPMarked ‘STOP’.Module available white only.
500BESPMarked ‘EMERGENCY STOP’.Module available white only.
BLANK MODULES
500IDBLANK MODULE for CIRCUIT IDModule comes with blank labelfor printing appliance details orcircuit identification. A clear,clip-on cover protects the label.
500ID
518M
518MBT OUTLET JACKIDC connections.For secondary connections.
Available white only.
COMMUNICATION MODULES
617M2
617M2BT OUTLET JACKTwo-wire outlet for two-wireinstallations.IDC connections.Two-wire outlets are notcompatible with three-wiresystems.Approved to Telepermit PTC 223.
TELEPERMITA P P R O V E D
519M6
519M6FCC 6-WAY OUTLET JACKIDC connections.For secondary connections.
500TT
500TTIDC TERMINATING TOOLFor use with Cat 617M2,518M and 519M6.
Available white only.
CAT 5e
COMMUNICATION MODULES cont...
Page 39
COMMUNICATION MODULES cont...
619MKLC
619MKLCDATA JACK ADAPTOR MODULEwith HINGED LIDAs for 619MKC but with hinged,gravity lid to facilitate circuitidentification and protect datasocket from dust when not in use.
619MALC
619MALCDATA JACK ADAPTOR MODULEwith HINGED LIDAs for 619MAC but with hinged,gravity lid to facilitate circuitidentification and protect datasocket from dust when not in use.
619MM
619MMDATA JACK ADAPTORMODULEAccepts Cat 5 RJ45 data jacksfrom Modtap.
619MAC
619MACDATA JACK ADAPTOR MODULEAccepts Cat 5 RJ45 data jacksfrom AT&T and Suttle.
619MDL
619MDLDATAPLUS CAT 5 RJ45MODULE with HINGED LIDAs for 619MD but with hinged,gravity lid to facilitate circuitidentification and protect datasocket from dust when not in use.
619MKC
619MKCDATA JACK ADAPTOR MODULEAccepts Cat 5 RJ45 data jacks inthe Keystone form from Krone,Amp, Hubbell, Suttle, HPM orDataplus.
528MF
528MFCOAXIAL CABLE SOCKET withREAR ‘F’ CONNECTIONRating: 75 Ohm.PAL type socket with ‘F’ connect inrear. Marked ‘TV’.
528MFIAs for 528MF but marked ‘IN’.
528MFOAs for 528MF but marked ‘OUT’.
528MFSAs for 528MF but marked ‘SKY’.
528MFVAs for 528MF but marked‘VIDEO’.
CAT 5e
Page 40
COMMUNICATION MODULES cont...
541M
541MRCA AUDIOCONNECTION SOCKETSolder type terminals.Socket coloured RED.
542MAs for 541M but socket colouredBLACK.
543MAs for 541M but socket colouredYELLOW.
509M
509MTV-FM SPLITTER SOCKETMODULESingle coaxial connection tocombined TV-FM aerial.Suits 75 Ohm coaxial cable.Comprising screw terminal forsignal core and saddle clamp forearth screen.Marked ‘FM’ and ‘TV’ onrespective modules.Suits 662VH and 682VH.Can be used as an outlet onmaster aerial systems.
528M
528MCOAXIAL CABLE CONNECTIONSOCKETRating: 75 Ohm.PAL type socket marked ‘TV’.Clamp terminals.
528MIPAL ISOLATED MODULERating: 75 Ohm.PAL type socket marked ‘TV’.Cable connection coaxial socketmodule. Mains isolated for240V a.c. For safety in hazardousenvironments.
529MAs for 528M but marked ‘FM’.
615MST
615MST‘ST’ TYPE FIBRE OPTICCONNECTOR MODULE‘ST’ multi-mode throughconnector.Comes with two yellow dustcovers in place.
615MBB
615MBBBANANA BINERY POSTRating: 12V - 250V a.c., 10A.Suits standard banana plug.Accepts wire and forkedterminal connections.Black band.
615MRBAs for 615MBB but with a redband.
516M
516MBNC SOCKETRating: 50 Ohm.Solder terminals.
615MF
615MF‘F’ TYPE CONNECTOR MODULE‘F’ Female/Female throughconnector.
615MFTVAs for 615MF but marked ‘TV’.
Page 41
629F
629FCEILING MOUNTING BASEDiameter: 90mmFor use with Cat 629 BattenHolder or Cat 44A CeilingRose.
Available white only.
629
629BATTEN HOLDER withCLIP-ON COVER PLATEBase: 71mmMounting centres: 51mm4 terminals, each capable ofaccepting 4 x 2.5mm2 cable.Terminals are shrouded andfingerproofed.Backed-off terminal screws allface one direction.Rating: 250V a.c., 50Hz,150W max.
Available in White only.
Metal cover plate N/A.
BATTEN HOLDER
MODULE SHROUD
680S
680SMODULE SHROUDFlame retardent material.Insulates up to 3000V.Suits all 500 Series and600 Designer Series modules.
Available grey only.
MODULE EJECTOR
600ME
600MEMODULE EJECTORFor removing 500 Seriesand 600 Designer Seriesmodules from plates.Collapses module clip-in legssimultaneously and ejectsmodule.
Supplied in various colours.
BATTEN HOLDER CEILING MOUNTING BASE
Page 42
573
573PULL CORD SWITCHPlate: 66mm diameterMounting centres: 50mmRated at 230V - 240V a.c., 50Hz.Fitted with 581M16PS 2-WayPull Cord Switch module.16A resistive, 16A inductive,8AX fluorescent.
Available white only.
548BS
548BSSOLAR WATER HEATERBOOSTER SWITCHPlate: 118mm (h) x 74mm (w)Mounting centres: 84mmRated at 230V - 240V a.c.,50Hz, 20A. Operates when avoltage across the lineterminals is present. Provides aboost of electric heat whenwater usage exceeds thecapability of the solar waterheating system.
Available white only.
572
572HOT WATER SYSTEM SWITCHPlate: 66mm diameterMounting centres: 50mmat 45°Round surface mounting.Rated at 230V - 240V a.c., 50Hz.Fitted with 681M20HWS2-Way 20A switch for conduitbox mounting.
Available white only.
CEILING SWITCHESHOT WATER SWITCHES
574
574HOT WATER SYSTEM SWITCHPlate: 79mm x 52mmSurface mounting.Rated at 230V - 240V a.c., 50Hz.Two fixing points, fitted with681M20HWS.2-Way 20A switch.Clamp provided for conduit andflexible cord.2 x 501T terminals included.
Available white only.
546
546UNIVERSAL TIME SWITCHPlate: 118mm x 74mmMounting centres: 84mmRated at 230V-240V a.c., 50Hz,10AX resistive and inductive.Can be set to switch a loadeither ON or OFF for a selectedtime period from1 sec to 31.5 hours.
Available white only.
TIME SWITCH
573N
573NNEON PULL CORD SWITCHPlate: 66mm diameterMounting centres: 50mmRated at 230V - 240V a.c., 50Hz.Fitted with 580M16NPS 1-Wayneon Pull Cord Switch module.Neon can be wired:• Permanently ON• ON to indicate ON• ON in the OFF position as a
locator.
Available white only.
ADDITIONAL ACCESSORIESAccessories on pages 42 - 45 are from the 500 Series range; there is no equivalent in the 600 Designer Series. Features of these products include low-gloss finish,front-loading modules, 16A & 20A switch ratings, backed-off terminal screws, ready-to-go fixing screws, Phillips/slotted screw heads, and fixed wall plates.
Page 43
596/56RCD-30
596/56RCD-30PLATE MOUNTED RCDPlate: 118mm x 74mmMounting centres: 84mmRated at 230V - 240V a.c.,50Hz, 20A. Protected to IP56.Tested to AS3190:1990 andAS3100:1990.RCD protects all socket outletsor permanently-wiredappliances wired downstream.Its IP56 flush plate allows it tobe used in damp or dustyconditions.Switches off the current within30ms if electrical leakage toearth exceeds as little as 30mA.Suits Cat 89DP MountingBlock, Cat 144 Flush Box andCat 145V, 146V or 148VMounting Bracket.
Available white only.
WATERPROOF SAFETY SWITCHKEY LOCK SWITCHES
568, 568ON & 568OFF
568KEY LOCK SWITCHLOCKABLE ‘ON’ OR ‘OFF’Plate: 118mm x 74mmMounting centres: 84mmRated at 230V - 240V a.c.,50Hz, 16A, 2-Way.Suits Cat 89, 536 or 537Mounting Block, Cat 144 FlushBox and Cat 145V, 146V or148V Mounting Bracket.
Available white only.
568ONKEY LOCK SWITCHLOCKABLE ‘ON’Plate: 118mm x 74mmMounting centres: 84mmRated at 230V - 240V a.c.,50Hz, 16A, 2-Way.Suits Cat 89, 536 or 537Mounting Block, Cat 144 FlushBox and Cat 145V, 146V or148V Mounting Bracket.
Available white only.
568OFFKEY LOCK SWITCHLOCKABLE ‘OFF’Plate: 118mm x 74mmMounting centres: 84mmRated at 230V - 240V a.c.,50Hz, 16A, 2-Way.Suits Cat 89, 536 or 537Mounting Block, Cat 144 FlushBox and Cat 145V, 146V or148V Mounting Bracket.
Available white only.
568CKKEY LOCK SWITCHCOMMON KEYas for Cat 568
Available white only.
Page 44
545 & 547
545SINGLE POLE SWITCHPlate: 118mm x 74mmMounting centres: 84mmRated at 230V - 240V a.c., 50Hz,45AX inductive and 45Aresistive, 1-Way.Has ‘E’ & ‘N’ loop terminals.Suits Cat 89, 536 or 537Mounting Block, Cat 144 FlushBox and Cat 145V, 146V or 148VMounting Bracket.
Available white only.
547DOUBLE POLE SWITCHPlate: 118mm x 74mmMounting centres: 84mmRated at 415V a.c., 50Hz, 45AXinductive and 45A resistive, 1-Way.Suits Cat 89, 536 or 537Mounting Block, Cat 144 FlushBox and Cat 145V, 146V or 148VMounting Bracket.
Available white only.
RANGE SWITCHES
576
576RANGE SOCKETPlate: 118mm x 74mmMounting centres: 84mmRated at 230V - 400V a.c.,50Hz, 32A max, single or twophase cookers. 4 pin.Recommended for use with6mm2 two core with Earth orthree core with Earth TPS.Complies with AS3100 andAS3131.Compatible with Cat 976 RangePlug.Suits Cat 144 Flush Box orCat 89 or 537 Mounting Block.
Available white only.
RANGE SOCKET
Page 45
AUTOMATIC LIGHTING SENSOR SWITCH
556
556PIR SENSOR SWITCHPlate: 118mm x 74mmMounting centres: 84mmRated at 230V - 240V a.c., 50Hz,500W incandescent max,250W fluorescent max.Interior sensor which replacesstandard switch and turnslights ON automatically when itsenses movement.Field of view: 90° elliptical.Range: 5m forward and 5meither side of centre.Time setting: 20 seconds to 10minutes.Lux setting: 5 Lux upwards.Suits Cat 89, 536 or 537Mounting Block, Cat 144 FlushBox and Cat 145V, 146V or148V Mounting Bracket.
Available white only.
593LRP
593LRPSINGLE THREADED SOCKETwith PLUGPlate: 118mm x 74mmMounting centres: 84mmRated at 230V - 240V a.c.,50Hz, 10A.Comes complete withCat 905LR plug.Suits Cat 537 or 89 MountingBlock, Cat 144 Flush Box andCat 145V, 146V or 148VMounting Bracket.
Available white only.
THREADED SOCKET
146H
146HHORIZONTAL BRACKETNailed stud bracket forstandard plate size 600 DesignerSeries accessories.84mm product mountingcentres.
146T2
146T2TWIN STUD BRACKETNailed stud bracket for twostandard plate size 600Designer Series accessories.The bracket’s design providesfor segregation of services asper AS/NZS 3000:2000,Section 3.9.9.3.84mm product mountingcentres.
MOUNTING ACCESSORIES
Page 46
MOUNTING BRACKETS
144PT
144PTFLUSH BOXPlastic threaded plate fixingholes.84mm x 52mm opening.84mm product mountingcentres, 48mm deep.Large cable entries for ease ofwiring.Side mounting by nails.Provision for horizontal orvertical mounting to studs.Provision for angled screwfixing through side wall.
144MTFLUSH BOXAs for 144PT but with threadedbrass plate fixing holes.
FLUSH BOXES
149
149FLUSH BOXSize: 135mm x 96mm x57mm deep.Mounting centres: 84mmSuits Cat 675HRCD and dualand combination cover plates.Comes complete withsegregation barrier andearthing terminal.
146V
146VVERTICAL BRACKETNailed stud bracket forstandard plate size 600Designer Series accessories.84mm product mountingcentres.
558
MOUNTING BRACKETS cont...558HORIZONTAL BRACKETfor WORKTOP PLATES80mm product mountingcentres.Suits Cat 688VH, 689VH, 698,698N, 698R and 698/15.
559HORIZONTAL BRACKETfor WORKTOP PLATES150mm product mountingcentres.Suits Cat 699, 699N, 699TB,699TBR and 699TB/15.
Page 47
145V
148V
148H
145VVERTICAL BRACKET84mm product mountingcentres.Nails can be inserted at the side.Suits all standard plate size600 Designer Seriesaccessories.
148HHORIZONTAL BRACKET84mm product mountingcentres.Opening 52mm x 76mm.Suits all standard plate size600 Designer Seriesaccessories.
148VVERTICAL BRACKET84mm product mountingcentres.Opening 52mm x 76mm.Suits all standard plate size600 Designer Seriesaccessories.
539
539MOUNTING CLIP40mm mounting centres forscrew fixing.Suits all 500 Series and600 Designer Series modules.
MODULE MOUNTING CLIPS
533
533PANEL MOUNTING CLIPA 30mm square hole isrequired.Clip will accommodate metalthickness from 20SWG to16SWG (1.0mm - 1.5mm).Suits all 500 Series and600 Designer Series modules.
89M
89MUNIVERSAL MOUNTING BLOCKSize: 122mm x 80mmx 37mm deep.84mm product mountingcentres.Suits all standard size600 Designer Seriesaccessories.
Available Australia only.
89SMAs for 89M but 18mm deep. 531
531SPACER (standard size)Size: 118mm x 75mmx 13mm deep.84mm product mountingcentres.
537
537DEEP MOUNTING BLOCKSize: 120mm x 77mmx 35mm deep.84mm product mountingcentres.Knockouts as for Cat 536.Suits all standard size600 Designer Seriesaccessories.
536
536SHALLOW MOUNTING BLOCK(standard size)Size: 119mm x 76mm x 25mmdeep.84mm product mountingcentres.4 x 25mm knockouts,12 x 20mm knockouts,12 x 16mm knockouts,12 TPS cable knockouts.Suits all standard size600 Designer Seriesaccessories.
MOUNTING BLOCKS & SPACERS
89
89UNIVERSAL MOUNTING BLOCKSize: 122mm x 80mmx 30mm deep.84mm product mountingcentres.Suits all standard size600 Designer Seriesaccessories.
Available New Zealand only.
89SPAs for 89 but 18mm deep.
89DPAs for 89 but 37mm deep.
557
557MOUNTING BLOCK SPACERSize: 118mm x 75mm x 12mm.For use with Cat 89 MountingBlock for surface mountingextra deep accessorieseg Cat 675 Shaver Socket.
560
560SINGLE ARCHITRAVEMOUNTING BLOCKSize: 79mm x 33mmx 25mm deep.62mm product mountingcentres.4 x 16mm knockouts,4 x TPS cable knockouts.Suits Cat 661VH and 662VHArchitrave Plates.
Page 48
89DI
89DIDOUBLE INSULATED MOUNTINGBLOCKSize: 122mm x 80mmx 37mm deep.84mm product mountingcentres.4 moulded conduit entry points(20mm & 25mm options).Suits all standard size600 Designer Series accessories.
Available in White only.
535
535POWER TOWERSize: 158mm x 158mmx 140mm high.Takes 4 x standard, vertical600 Designer Series plates.Fitted with divider forsegregated services.1 central 25mm conduit entryand 4 x 25mm knockouts.Cover has aperture for 500Series and 600 Designer Seriesmodules.
565
565DOUBLE ARCHITRAVEMOUNTING BLOCKSize: 132mm x 33mmx 25mm deep.2 mounting holes.114mm product mountingcentres.8 x 16mm knockouts,8 x TPS cable knockouts.Suits Cat 663VH and 664VHArchitrave Plates.
567S
567SSHORT WORKTOPMOUNTING BLOCKSize: 103mm x 51mmx 30mm.80mm product mountingcentres.4 x 16mm knockouts,4 x TPS cable knockouts.Suits Cat 688VH, 689VH, 698,698N, 698/15 and 698R.
MOUNTING BLOCKS & SPACERS cont...
567L
567LLONG WORKTOPMOUNTING BLOCKSize: 173mm x 51mmx 30mm.150mm product mountingcentres.8 x 16mm knockouts,8 x TPS cable knockouts.Suits Cat 699, 699N, 699TB,699TB/15 and 699TBR.
Page 49
535F
535FFLUSH FLOOR SOCKETRatings: 230V - 240V a.c.,
50Hz, 10A.Projection above the floor:10mm at highest point.Projection below the floor:52mm.Overall diameter: 130mmCut-out for the base:97 - 100mm diameter.Knockouts: 1 x 25mm.Conduit entries: 2 x 25mm.
Available in Grey only.
FLOOR SOCKET
FLOOR MOUNTED ACCESSORIES
POWER TOWER
640RC
640RCFOUR GANGMOUNTING BLOCKSize: 196mm x 84mmx 19mm high.84mm product mountingcentres.7 x 20mm Knock-outs.Round conduit adaptor 25mm.Suits Cat 644, 644N, 644P,644/15, 641, 641N, 641P and641/15.
Available in White only.Also Cat 640SC includingsquare conduit adaptor25.5mm x 16.5mm.
538
538CONVERSION PLATEPlate: 118mm x 118mm.Mounting centres (plate tobox): 84mm x 46mm.Plate mounting centres: 84mm.
Plate adapts existing2-gang installation to600 Designer Series standardplate size.
CONVERSION PLATE
MULTI-GANG STAINLESS STEEL SWITCH PANELS
STAINLESS STEEL SWITCH PLATES
534P8S
534P8SSTAINLESS STEELSWITCH PLATE8-WaySize: 128mm x 220mm.Supplied with 8 x Cat 533 WhiteModule Mounting Clips.
534P16S
534P16SSTAINLESS STEELSWITCH PLATE16-WaySize: 220mm x 220mm.Supplied with 16 x Cat 533 WhiteModule Mounting Clips.
534P24S
534P24SSTAINLESS STEELSWITCH PLATE24-WaySize: 313mm x 220mm.Supplied with 24 x Cat 533 WhiteModule Mounting Clips.
534B8
534B8SWITCH PANELWALL BOX8-WaySize: 108mm x 200mmx 60mm deep.1 earth terminal.Side knockouts: 2 x 38mm,4 x 25/21mm.Back knockouts: 11 x 38mm,2 x 25/21mm.
534B16
534B16SWITCH PANELWALL BOX16-WaySize: 200mm x 200mm x 60mmdeep.1 earth terminal.Side knockouts: 2 x 38mm,4 x 25/21mm.Back knockouts: 2 x 38mm,4 x 25/21mm.
534B24
534B24SWITCH PANELWALL BOX24-WaySize: 293mm x 200mm x 60mmdeep.1 earth terminal.Side knockouts: 2 x 38mm,4 x 25/21mm.Back knockouts: 3 x 38mm, 4 x 25/21mm.
SWITCH PANEL WALL BOXES
PDL’s switch panels accept all 500 Series and 600 DesignerSeries modules but they must be ordered separately.Standard plate finish is brushed stainless steel but polishedbrass plates are available on request. Mounting Boxes aresupplied separately.
Page 50
501T
501TSINGLE SCREW TERMINAL32ATerminal accepts 2 x 6mm2 or3 x 4mm2 conductors.
501JARSINGLE SCREW TERMINALS32A, BULKJar of 100 single screwterminals (32A).Terminals accept 2 x 6mm2 or3 x 4mm2 conductors.
TERMINALS
Page 51
MISCELLANEOUS ACCESSORIES
501L1
501L1SINGLE SCREW TERMINAL40ATerminal accepts 3 x 6mm2
conductors.
501L1/50SINGLE SCREW TERMINALS40A, BULKJar of 50 single screwterminals (40A).Terminals accept 3 x 6mm2
conductors.
501L2
501L2TWIN SCREW TERMINAL40ATerminal accepts 3 x 6mm2
conductors.
501L2/40TWIN SCREW TERMINALS40A, BULKJar of 40 twin screw terminals(40A).Terminals accept 3 x 6mm2
conductors.
544
544JUNCTION BOXSize: 67mm x 67mmx 37mm deep.Rated at 32A, 500V.4 mounting holes 51mm x51mm.Includes 4 x 501T terminals,fully shrouded.Each terminal accommodates4 x 2.5mm2 cables.
JUNCTION BOXES
544J
544JJUNCTION BOXSize: 65mm x 92mmx 45mm deep.Rated at 40A, 500V.Includes 1 twin and 3 singlescrew terminals, fullyshrouded. Each terminalaccommodates3 x 6mm2 cables.Comes with two ready-fix nailsin the base.
PDL's surge protected switched socket protects valuable electronicequipment from the damaging effects of high voltage surges.
All sockets on the same circuit as the 695SP are protected againstpower surges upstream and downstream.
The front -loading surge protection module can be replaced easilyand safely, and there is provision for tamperproofing.
PDL’s surge protected switch socket is featured on page 23.
Page 52
PDL's recessed sockets with 360º safety shrouds around thepin holes, meet the specifications in AS/NZS 3112 for recessedsockets, to give maximum safety at the interface between plugand socket. Refer to AS/NZS 3000:2000 Clause 4.9.1.2.
AS/NZS 3112 recognises the danger of contact with the live pinsof a partially-inserted plug and recommends recessed sockets toprevent this type of electrical accident.
Sockets with safety shrouds are featured on pages 24, 25, 27and 28.
Recessed Sockets withSafety Shrouds
Focus on Risk Management
Surge Protection
Front-loading switch modules cannot be pushed back into the wallcavity by frontal impact, ensuring end-user safety by preventingaccidental access to live areas.
Front-Loading Modules
PDL’s innovative waterproof switches are designed forbathrooms, ensuites, kitchens and laundries. They’re alsoideal for switching appliances such as waste disposals anddishwashers, offering protection from an electric shockwhen an appliance or a light is switched on by someonewith wet hands.
PDL waterproof switches meet the requirements forinstallation in Zone 1 as per AS/NZS 3000:2000,Sections 7.1, 7.2 and 7.6 and NZS 3000:1997,Sections 702.9.2 and 702.9.3.
Waterproof switches are featured on pages 9 & 10.
Waterproof Switches
PDL’s safety switches (Cat 696RCD-10 and 696RCD-30)provide 10mA or 30mA RCD protection for a number ofsocket outlets or permanently-wired appliances on thesame circuit.
The Powerguard RCDs switch off the current within 30milliseconds (30 thousandths of a second) if electricalleakage to earth exceeds as little as 10mA (10 milliamps)or 30mA (30 milliamps).
That could mean the difference between life and death.
Safety switches are featured on page 22.
Safety Switches
Page 53
Safety Shuttered Sockets
For additional safety, all PDL 600 Designer Series socket pinholes are fitted with safety shutters.
Page 54
ELECTRICAL PRODUCTSPDL Electrical Products are available through electrical wholesalers New Zealand wide. Visit our website www.pdl.co.nzPDL Electrical Products are designed and engineered to ISO 9001. Freecall 0800 652 999. Freefax 0800 101 152. Email: [email protected]
PDL is a brand of Schneider Electric
The spa pool is heating. The lightsare dimmed. The mood is set.And, best of all, inten minutes, you’ll behome to enjoy it.
PDL’s revolutionary e.BOSelectronic buildingoperating systemuses sophisticatedmicroprocessortechnology to giveyou control of yourhome. Lights fadeon and off as you enterand leave rooms, yourpreferred temperatureis created, curtainsopen and close as thesun rises and sets,freshly-brewed coffeegreets you in the morningsand home security and safetyis constantly monitored.
For information on e.BOSelectronic building operatingsystems, for new homes orcommercial premises, contactPDL by e-mail [email protected] or phone0800 PDL eBOS (0800 735 3267).
Page 55
ELECTRICAL PRODUCTSPDL Electrical Products are available through electrical wholesalers New Zealand wide. Visit our website www.pdl.co.nzPDL Electrical Products are designed and engineered to ISO 9001. Freecall 0800 652 999. Freefax 0800 101 152. Email: [email protected]
PDL is a brand of Schneider Electric
Rated the best for the worstelectrical conditionsPDL 56 SERIES
PDL’s 56 Series is the proven,watertight solution for toughindustrial environments.
Check these features...• Dustproof and
waterproof to IP66.• Manufactured from
high impact, greypolycarbonateas standard.
• Maximum UVresistance.
• 95x95mm platemodule for up tonine gangcombinations.
• One-piece,internally wiredcombinationswitched sockets.
• Sockets available with30mA RCD protection.
• Chemically-resistantorange and whiteversions available.
• Switches carry AC23A andAC3 motor ratings to EN60974,making them suitable for switchingDOL motors.
Page 56
TECHNICAL DATA WIRING DIAGRAMS
A/P (Red)
1
L
C N
Load
A/P (Red)
1
L
C N
Load
2
680M20N & 580M16NPS one way switches with neon
Neon permanently ON Neon ON, switch OFF (locator) Neon ON, switch ON (indicator)
Neon wires Neon wires Neon wires
Rear view of switch modules
2
A/P (Red)
1
L
C N
Load
578M16 Intermediate Switch
Rear view of switch modules
N (Black)
LOAD
A/P (Red)
681M20 2 way switch 578M16 intermediate switch 681M20 2 way switch
Any number of intermediate switches can be wired between the 2 way switches
2
1
L
C
2
1
L
C
3
12
4
681M20 Module Master Switching for Security
2
1
C2
1
C2
1
C2
1
C
681M20 681M20 681M20 681M20
N (Black)
A/P (Red)
687M3 Rotary Switch Module
687M4 Rotary Switch Module
Front
1
2
03
2C
Rear
3
2C 180°
Front
03
1
C
Rear
3
1C
180°
Internal from front
Internal from front
I
II
Front
2
3
13
2C
Rear
3
2C
360°
01
1Internal from front
Page 57
WIRING DIAGRAMS
620K Dimmer Two way circuit
Blue wireE (Green)
2
1
C
681M20
Loop2
1
C
681M20
White wireBrown wire
Lamp
A/P (Red)
N (Black)
620KDimmer
Lamp
620K Dimmer One way circuit
Loop2
1
C
681M20
White wireBrown wire
Lamp
A/P (Red)
N (Black)
Lamp620KDimmer Blue wireE (Green)
620 Dimmer & 520M Dimmer Module Two way circuit
2
1
C
681M20
Loop2
1
C
681M20
Lamp Lamp
A/P (Red)
N (Black)
White wire
White wire
520MDimmerModule
620 Dimmer & 520M Dimmer Module One way circuit
Loop2
1
C
681M20
Lamp LampA/P (Red)
N (Black)
White wire
White wire
520MDimmerModule
Page 58
625C3 & 625C3/1 Fan Controllers
Active
3
C
1
2
Neutral
Fan Motor 100VA maxRed
Purple
Brown
691RCD-30
A/PA/P (Red)
NN (Black) N OUT
E (Green)
A/POUT
LINE INAdditionalSocketOutlet
N
A/P
LOAD A
A (Red)LINE A
N (Black) LOAD N
E (Green)
695RCD
AdditionalSocketOutlet
N
A/P
LINE N
E
695RCD-10 & 30
696RCD-10 & 696RCD-30
A/P
N (Black)
E (Green)
LINE
696RCD
SocketOutlet
N
A/PA/P (Red)
N
A/P LOAD N
E
N
A/P
E
SocketOutlet
WIRING DIAGRAMS
Page 59
WIRING DIAGRAMS
648T5/15/30/60/120 Push Button Timers
Cat 646E7
N.C.N.O.A/PN
LOAD
A/P(Red)
N(Black)
A/P Line In
N
A/P Out
N
A/P Brown
N Blue
Standard Wiring for RJ45 Jack(Jack face shown)
PAIR 1
PAIR 2
PAIR 3
PAIR 4
White/blue
Blue
White/orange
Orange
White/Green
Green
White/Brown
Brown
TIP
RING
TIP
RING
TIP
RING
TIP
RING
Configuration: 568A
PAIR 3 PAIR 1 PAIR 4
PAIR 2
RJ45 EIA-T568A
Configuration: 568A
PAIR 2 PAIR 1 PAIR 4
PAIR 3
RJ45 EIA-T568B
1 2 3 4 5 6 7 8W-O O W-G BL W-BL G W-BR BR
JACK POSITIONS
1 2 3 4 5 6 7 8W-G G W-O BL W-BL O W-BR BR
JACK POSITIONS
646E7 Electronic Timer
619MD & 619MDL CAT 5 RJ45 Jack Module
110 punch down tool trim flush Place caps to fix wiresOR
Page 60
Quality Management
PDL Industries Limited,Telarc Reg. No. 061registered to ISO 9002.
NATIONALACCREDITATION
OF CERTIFICATIONBODIES
ISO 9002CERT NO. 11595
QU
ALIT
Y
ASSESSED
REGISTEREDSUPPLIER
PDL Electrical Products aremanufactured by
The design and manufacture of products by PDL has always been backed by third party testing anddevelopment facilities.
PDL uses Parkside Laboratories, an independent IANZ-registered electrical laboratory, for its producttesting and IANZ-endorsed test reports to ensure international product acceptance.
Parkside Laboratories offers testing and certification services in the fields of electrical, EMC,environmental, calibration and metrology, with test procedures performed in accordance with ISO Guide17025 and ISO 9001. Their in-house Quality Management Systems meet International AccreditationNew Zealand (formerly known as TELARC) standards, ensuring that all procedures meet or exceed therequirements of the New Zealand Code of Laboratory Management Practice.
The facility has also expanded to encompass information technology, telecommunications equipmentand test electrical equipment for explosive atmospheres. EMC facilities have also been extended andParkside now boasts its own outside open area test site (OATS).
As an International Accreditation New Zealand registered laboratory, Parkside Laboratories' test resultsare recognised and accepted by other accreditation authorities in the following countries: Australia,the United States of America, Ireland, the United Kingdom, Portugal, Spain, France, Belgium,the Netherlands, Germany, Austria, Switzerland, Italy, Denmark, Norway, Sweden, Finland, China,Chinese Taipei, Hong Kong, Singapore, South Africa, Czech Republic, Korea, and Japan.
In 1998, Parkside Laboratories became the first laboratory in New Zealand and one of the first in theworld, to be granted Conformity Assessment Body status for CE marking outside the European Union.
The combination of research, development and quality assurance has underpinned the current successof PDL electrical and electronic products.
An independent International Accreditation New Zealand registered electrical laboratory is used for product testingto ensure compliance to international standards and product quality.
Page 61
NOTES
Page 62
89 4889DI 4889DP 4889M 4889SM 48
89SP 48144MT 46144PT 46145V 47146H 46146T2 46146V 46148H 47148V 47149 46500B 38500BESP 38500BSP 38500BST 38500ID 38500TT 38501JAR 51501L1 51501L1/50 51501L2 51501L2/40 51501T 51509M 40510ML12 35510ML24 35510MLD24 35510MN 35516M 40518M 38519M6 38520M 36521M 36528M 40528MF 39528MFI 39528MFO 39528MFS 39528MFV 39528MI 40529M 40531 48533 47534B8 50534B16 50534B24 50534P8S 50534P16S 50534P24S 50535 49535F 49536 48537 48538 49539 47541M 40542M 40543M 40544 51544J 51545 44546 42547 44548BS 42551M2 37556 45557 48558 47559 47560 48
INDEX BY CATALOGUE NUMBER626VC2 13626VC4 13628 31628F 31629 41629F 41632 12640RC 49641 26641C 19641N 26641P 26641/15 26644 29644C 19644N 29644Z 29644ZC 19644/15 29646E7 12646E7C 18646E7MBBZ 18646E7MPB 18646E7MSS 18646R7 12646R24 12646R24C 18646R24MBBZ 18646R24MPB 18646R24MSS 18646RTC 12648T5 12648T15 12648T30 12648T60 12648T120 12650BC 18650BMBBZ 18650BMPB 18650BMSS 18650BVH 16650VH 16651 10651VWP 10661C 18661MBBZ 18661MPB 18661MSS 18661VH 16662C 18662MBBZ 18662MPB 18662MSS 18662VH 16663C 18663VH 16664C 18664VH 16666TMB24 35666TML24 35675 22675HRCD-30 22679C 18679H/2 11679MBBZ 18679MPB 18679MSS 18679V/2 11679VN/2 11680 11680M32 34680M32AC 34680M32H 34680M32I/O 34680M32O 34
565 49566MNCB 35567L 49567S 49568 43568OFF 43568ON 43572 42573 42573MM 37573N 42574 42576 44578M16 33580M16NPS 37581M16HF 34581M16HFAL 34581M16HFCL 34581M16HFF 34581M16HFMW 34581M16HFSE 34581M16PBM 37581M16PBP 37581M16PBS 37581M16PS 37587M10 33593LRP 45596/56RCD-30 43600ME 41600SPM 23610TML24 35612C 19612MBBZ 19612MPB 19612MSS 19615MBB 40615MF 40615MFTV 40615MRB 40615MST 40617BT2 31617BT2/2 31617M2 38619MAC 39619MALC 39619MD 38619MDL 39619MKC 39619MKLC 39619MM 39620 11620K 11625 11625C 18625C3 11625C3/1 11625C3M 36625C3/1M 36625MBBZ 18625MPB 18625MSS 18625X 11625XC 18625XMBBZ 18625XMPB 18625XMSS 18626N 13626NC 18626NMBBZ 18626NMPB 18626NMSS 18626VCC 18626VCMBBZ 18626VCMPB 18626VCMSS 18
Cat No. Page Cat No. PageCat No. Page
INDEX BY CATALOGUE NUMBERCat No. Page Cat No. Page Cat No. Page
Page 63
683VWPD 9683WPC 18683WPMBBZ 18683WPMPB 18683WPMSS 18683-683C 20683-692C 20684 8684C 18684-684C 20684HID 15684HWP 10684HWPD 10684MBBZ 18684MPB 18684MSS 18684VH 14684VID 15684VWP 10684VWPD 10685 8685VH 14686 8686C 18686MBBZ 18686MPB 18686MSS 18686VH 14686-686C 20687M3 35687M3A/M 35687M3I/II 35687M4 35687M4F 35688C 18688MBBZ 18688MPB 18688MSS 18688VH 16689C 18689MBBZ 18689MPB 18689MSS 18689VH 16691 24691C 19691MBBZ 19691MPB 19691MSS 19691R 24691RCD-30 21691RCDC 19691RCDMBBZ 19691RCDMPB 19691RCDMSS 19691X 24691XC 19691XMBBZ 19691XMPB 19691XMSS 19691Z 24691ZC 19691/15 24692 24692C 19692ID 25692MBBZ 19692MPB 19692MSS 19692N 25692P 25692R 25692X 25692XC 19692XMBBZ 19
680M32R 34680MBBZ 18680MPB 18680MSS 18680S 41680TMNPB 36680TMPB 36681 8681C 18681HID 15681HWP 9681M20 33681M20AC 34681M20A/M 34681M20B 33681M20D 34681M20DR 34681M20DW 34681M20DY 34681M20F 34681M20FG 34681M20F/R 34681M20G 34681M20GN 34681M20H 34681M20HD 34681M20HLF 34681M20HWS 33681M20I/O 34681M20L 34681M20LO 34681M20MR 34681M20MW 34681M20N 33681M20O 34681M20P 33681M20PL 34681M20PU 34681M20R 33681M20S 34681M20SE 34681M20TV 34681M20WH 34681M20WT 34681M20ST 34681MBBZ 18681MPB 18681MSS 18681VH 14681VID 15681VWP 9681-695C 20682 8682C 18682HID 15682HWP 9682MBBZ 18682MPB 18682MSS 18682VH 14682VID 15682VWP 9682VWPD 9682-681C 20
683 8683C 18683HID 15683HWP 9683HWPD 10683MBBZ 18683MPB 18683MSS 18683VH 14683VWP 9
692XMPB 19692XMSS 19692Z 25692ZC 19692/15 25692-681C 20692-692C 20693/2 31694 27694C 19694MBBZ 19694MPB 19694MSS 19694N 27694R 27694X 27694XC 19694XMBBZ 19694XMPB 19694XMSS 19694XX 27694XXC 19694XXMBBZ 19694XXMPBZ 19694XXMSS 19694Z 27694ZC 19694/15 27695 28695C 19695ID 28695MBBZ 19695MPB 19695MSS 19695N 28695P 28695R 28695RCD-10 21695RCD-30 21695RCDMBBZ 19695RCDMPB 19695RCDMSS 19695SP 23695X 28695XC 19695XMBBZ 19695XMPB 19695XMSS 19695Z 28695ZC 19695/15 28695-695C 20695-695XC 20696RCD-10 22696RCD-30 22698 30698C 19698MBBZ 19698MPB 19698MSS 19698N 30698R 30698/15 30699 30699C 19699TB 30699TB/15 30699TBC 19699TBMBBZ 19699TBMPB 19699TBMSS 19699TBN 30699TBR 301588M 35
PDL products are privileged to reside in almost every New Zealand home and
office. People touch PDL products millions of times across the country, every day.
PDL is also a significant exporter, earning foreign exchange for New Zealand by shipping industry-
best value-added product around the globe.
The PDL Electrical Products range (largely made in Christchurch) offers an extensive range of
switch and wiring accessories. The PDL Electronics range (made in Napier) involves high-tech
electronic solutions for industrial applications.
In just over six decades, PDL has stamped its indelible hallmark of quality and innovation on the
domestic, commercial and industrial markets in everything from electrical accessories to industrial
switchgear, AC variable speed drives to home automation.
Plastic & Die Casting Ltd, founded in 1947 was purchased by (the then) Bob
Stewart in 1957 and renamed PDL Industries Ltd. It was Sir Robertson Stewart's
acumen which created the vehicle which allowed PDL to grow and thrive for
the balance of the 20th century. PDL grew from 12 staff and sales of NZ$5000
per annum, to 2000 staff and NZ$350m sales across 3 continents - in 60 years.
PDL has now joined the Schneider family of leading electrical brands. Along with Merlin Gerin,
Telemecanique, Modicon and Square D - the PDL product ranges are now marketed locally by
Schneider Electric New Zealand.
Schneider Electric’s worldwide distribution network now also offers the PDL brand to a wider
global market, direct from the PDL plants in Christchurch & Napier.
PDL products continue to be designed and engineered by New Zealanders, from the independent
PDL manufacturing facilities in Christchurch & Napier. PDL is now, and will remain, a Kiwi brand
and we take pride in that.
NZO502PDL600, Pr inted May 2002, rep laces Febr uar y 2000 ed i t ionPDL i s a br and of Schne ider E lectr ic
PDL Electrical Products are available through electrical wholesalers
New Zealand wide.
PDL Electrical Products are designed and engineered to ISO 9001.
Resellers source PDL in New Zealand through Schneider Electric.
Freecall 0800-652 999, freefax 0800-101 152
Email orders to [email protected]
Online product detail - download from www.pdl.co.nz