FZ-SM02B-2 1.5~8kg(3.3~17.6lbs)RATED

Scan the QR code with your mobile device follow the link for know more about FEZIBO products.

https://www.facebook.com/Fezibous/?ref=bookmarks

Service@fezibo.com www.facebook.com/Fezibous www.fezibo.com

2 3

ASSEMBLY STEPS

STEP 1

PACKAGE CONTENTS

TOOLS NEEDED

Phillips Screwdriver

A (x2)Arm

B (x1)Clamp

C (x1)Clamp Cover

D (x2)VESA Plate

E (x1)Pole

F (x1)Cable Clip

G (x2)Thumbscrew

H (x3)Bolt

K (x1)4mm Allen Key

L (x1)6mm Allen Key

OPTION A: Clamp InstallationAdjust clamp (B) height according to thickness of desktop. Attach clamp cover (C) to clamp (B). Secure pole (E) to clamp (B) using three bolts (H). Tighten using 4mm Allen key (K).

I (x1)Support Plate

J (x1)Base

M-A (x8)M4x12

M-B (x8)M4x16

M-C (x8)M5x12

M-D (x8)M5x16

M-E (x8) D5 Washer

M-F (x8)Spacer

35-8

0mm

10-4

5mm

C

B

K

H

E

NOTE: SOME HARDWARE MAY NOT BE USED

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

TIPOVER WARNINGSERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARDSMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

17.6 lbs(8 kg)

DO NOT EXCEED WEIGHT CAPACITY.Failure to do so may result in serious injury.

PER ARM

4 5

STEP 1 (Continued)OPTION B: Grommet Base InstallationFor grommet hole attachment, disassemble clamp (B) using 6mm Allen key (L) and a Phillips screwdriver. Attach base (J) to pole (E) through ⅜” (10mm) grommet hole in desktop. Secure using bolt from clamp (B) and plate (I).

STEP 3Adjust arm (A) to desired height. Tighten using 6mm Allen key (L).

STEP 2Slide cable management clip (F) over top of pole (E). Adjust bolt on monitor arm (A) to slide over top of pole (E) as shown in diagram.

STEP 4

Attach VESA plate (D) to the back on monitor using bolts (M-A, M-B, M-C, M-D) and washers (M-E). For curved monitors, spacer (M-F) may be required.

M-E

M-AM-C

M-E

M-BM-D

M-F

D

I

0-40mmJ

F

A

L

L

6 7

STEP 5 STEP 7Adjust tension in arm and angle of monitor using 6mm Allen key (L). Clockwise reduces tension, counterclockwise increases tension. The tension should be just enough to hold your monitor in place without lifting itself up.

STEP 6

Slide VESA plate (D) over bracket on arm (A). Secure using thumb screw (G). Remove bottom covers from arm (A).

Run cables through bottom of arm (A). Re-attach covers.

G

Why choose FEZIBO?Many ergonomic office solutions come at high cost. Our mission is to useinnovation, creativity, and efficiency to produce a more affordable solutionthat doesn't sacrifice quality and is easily accessible to the millions of homeand office workers globally.

If any parts are received damaged or defective, please contact us. We are happy toreplace parts to ensure you have a fully functioning product.

For more FEZIBO products, check out our website at: www.fezibo.com

Service@fezibo.com www.facebook.com/Fezibous www.fezibo.com