Fyp cs
-
Upload
charith-sathyajith -
Category
Documents
-
view
70 -
download
3
Transcript of Fyp cs
![Page 1: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/1.jpg)
Aluminum – Graphite Thermo-electric module
Charith S Suriyakula
AS/07/08/077
Index # 2001
![Page 2: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/2.jpg)
Objective• To design and develop a low-cost and low-tech
thermo-electric generator module.
![Page 3: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/3.jpg)
The problem…• Fossil fuel is a limited resource of Earth. Fossil fuels are non-
renewable and is a finite resource.
• To meet the power demand of the world, people have to discover renewable energy sources.
• This is a solution for the expensive and environmentally damaging fossil fuels.
![Page 4: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/4.jpg)
Renewable energy sources• Main source is sunlight. Also known as Solar energy
o Can directly use to light, heat homes and other buildings.
o Can be used to generate electricity
o Hot water heating
• Wind energy is captured by wind turbines to generate electricity
• Hydro power is used to rotate turbines and generate electricity
![Page 5: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/5.jpg)
Waste Heat• In many cases, the efficiency of a process is limited due to
the energy loss as heat.
• We have to design the process to minimize the heat loss or to make use of the heat loss.
• Mechanical engines, computers generate heat which is wasted to air.
• The challenge is to convert the waste heat into a applicable energy form
![Page 6: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/6.jpg)
Heat Electricity ?• Seebeck effect is the phenomenon of
inducing electricity from heat
• It was first discovered by Thomas Seebeck in 1821
• Modern technology use semiconductor materials to design TEG devices
• TEGs are reliable efficient source of electricity
![Page 7: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/7.jpg)
Objective• To design and develop a low-cost and low-tech
thermo-electric generator module.
Glass slides
Copper wires
plastic
wood
aluminum
adhesivespaper
![Page 8: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/8.jpg)
Basic design
![Page 9: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/9.jpg)
![Page 10: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/10.jpg)
Improvements• The following cases were considered when designing the
TEG moduleo Heat conductivity from “hot” junction to “cold” junction needs to
be minimized.
o The temperature difference between “hot” and “cold” junctions needs to be maximized to induce higher energy from the module
o The contact points of two materials needs to be clearly specified.
o More couples = more power
![Page 11: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/11.jpg)
• More couples in a single glass slide.
• Still the contact points were not clearly visible.
![Page 12: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/12.jpg)
• The aluminum and graphite strips are connected using “L” shaped contact area.
![Page 13: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/13.jpg)
![Page 14: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/14.jpg)
![Page 15: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/15.jpg)
Results
![Page 16: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/16.jpg)
![Page 17: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/17.jpg)
![Page 18: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/18.jpg)
Discussion
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0 10 20 30 40 50 60
pe
r co
up
le v
olt
age
(µ
V)
temperature difference (0C)
Graph of ‘per couple voltage’ vs. ‘temperature difference when heated using an oil bath (Cell 5 vs. Cell 13)
Cell 5
Cell 13
Expon. (Cell 5)
Expon. (Cell 13)
Strip width comparison
![Page 19: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/19.jpg)
0.00
0.50
1.00
1.50
2.00
2.50
0 10 20 30 40 50 60 70
pe
r co
up
le v
olt
age
(µ
V)
temperature difference (0C)
Graph of ‘per couple voltage’ vs. ‘temperature difference when heated using an oil bath (Cell 01 vs. Cell 07)
Cell 01
Cell 07
Expon. (Cell 01)
Expon. (Cell 07)
Strip height comparison
![Page 20: Fyp cs](https://reader031.fdocuments.us/reader031/viewer/2022020307/55a3dfa61a28ab746d8b45bd/html5/thumbnails/20.jpg)