FWPS CENTRAL KITCHEN SECTION 092216 FEDERAL WAY … · 6. ASTM C754 - Standard Specification for...

FWPS CENTRAL KITCHEN FEDERAL WAY PUBLIC SCHOOLS 07792.00

SECTION 092216NON-STRUCTURAL METAL FRAMING

October 18, 2011 BID SET 092216 - 1 of 8

SECTION 092216 NON-STRUCTURAL METAL FRAMING

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Formed steel stud interior wall framing not subject to bearing and axial loads. 2. Formed steel studs and resilient channels and clips use for framing of gypsum board

ceiling with resilient attachment. 3. Deflection track.

B. Related Sections: 1. Section 054000 - Cold-Formed Metal Framing 2. Section 053100 - Steel Decking 3. Section 061000 - Rough Carpentry 4. Section 072116 - Blanket Insulation 5. Section 072113 - Board Insulation: Furring strips 6. Section 078400 - Firestopping 7. Section 081113 - Hollow Metal Doors and Frames 8. Section 083113 - Access Doors and Frames 9. Section 087100 - Door Hardware 10. Section 092226 - Suspension Systems 11. Section 095300 - Acoustical Ceiling Suspension Assemblies 12. Section 092900 - Gypsum Board 13. Division 21 - Fire Suppression 14. Division 23 - Heating, Ventilating, & Air Conditioning 15. Division 26 - Electrical

1.2 REFERENCES

A. Reference Standards: Current edition at date of Bid.

B. American Society for Testing and Materials (ASTM) International: 1. ASTM A568 - General Requirements for Steel, Sheet, Carbon and High-

Strength, Low-Alloy, Hot-Rolled and Cold-Rolled 2. ASTM A653 - Standard Specification for Steel Sheet, Zinc Coated

(Galvanized) or Zinc-Iron Alloy-Coated (Galvanized) by the Hot-Dip Process

3. ASTM A792 - Standard Specification for Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Process.

4. ASTM A875 - Standard Specification for Steel Sheet, Zinc-5% Aluminum Alloy-Coated by the Hot-Dip Process.

5. ASTM C645 - Standard Specification for Nonstructural Steel Framing Members

6. ASTM C754 - Standard Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products

7. ASTM C1002 - Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Bases to Wood Studs or Steel Studs.

8. ASTM E1966 - Standard Test Method for Fire-Resistive Joint Systems.




C. International Code Council (ICC) Evaluation Services, Website http://www.icc-es.org/Evaluation_Reports

D. Northwest Wall and Ceiling Bureau (NWCB), Tel (206) 524-4243 (Bob Drury, Mark Fowler), Website: http://www.nwcb.org 1. NWCB 200-100 - Screws. 2. NWCB 200-104 - Framing Tolerance. 3. NWCB 200-103 - Friction Fitting and Gap Tolerance of Metal Studs. 4. NWCB 200-500 - Non-Load Bearing Partitions and Lay-In Acoustical Ceilings.

E. Steel Stud Manufacturers Association (SSMA): Product Technical Information, Website http://www.ssma.com 1. SSMA ICC-ES Legacy Report ER-4943P, Revised Aug 2003 after revision. 2. SSMA Product Technical Information. 3. SSMA Industry Technical Note 2 – Unsheathed Flange Bracing.

F. Underwriters Laboratories (UL): UL 2079 - Tests for Fire Resistance of Building Joint Systems.

1.3 SYSTEM DESCRIPTION

A. System: Interior metal stud framing systems, plenums, furred ceilings, and soffits used in conjunction with sound insulation, and gypsum board systems.

B. Maximum Allowable Deflection: Design and size components for L/360 deflection at 5 psf loading.

C. Accommodate construction tolerances, deflection of building structural members, and clearance of intended openings.

1.4 SUBMITTALS

A. Submit under provisions of Sections 013300.

B. Product Data: 1. Published product information, code approvals accepted by ICC Evaluation Services,

specifications, and standard framing details. 2. Included framing components, lateral bracing, framed openings, bearing points,

anchorages, welds, screw fasteners, anchorage devices, splices, slip channels, backing for wall mounted items, and accommodation for wall mounted windows, doors, and hardware.

C. Design Data: Published Load table and criteria indicating section properties, height of wall limitations, combined axial and lateral load limitations, load and deflection criteria, and allowable loads for fasteners and welds.

D. Fire and Acoustical Assemblies: 1. Demonstrate equivalency to ICC, UL, GA, WH, and FM tests indicated by Contract

Documents. 2. Include ICC Evaluation Services acceptance for fire rated deflection track systems.




1.5 QUALIFICATIONS

A. Manufacturer: Member of Steel Stud Manufacturers Association (SSMA).

B. Installer: 1. Company specializing in work of this Section with minimum 3 years documented

experience in commercial quality work of comparable scope. 2. Recommended as qualified to perform work of this Project by Northwest Wall and

Ceiling Bureau (NWCB), or accepted by Architect.

1.6 REGULATORY REQUIREMENTS

A. Conform to regulatory requirements of Section 014100.

B. Design and Structural Properties: Conform to IBC Chapter 22, IBC Section 1632, AISI/NASPEC standards referenced by IBC, and SSMA ICC-ES Legacy Report ER-4943P as published by SSMA Product Technical Information.

C. Fire-Resistive Assemblies: Conform to Underwriters' Laboratories (UL) or other tested design reports acceptable to building code regulatory authority having jurisdiction.

D. Fire-Resistive Deflection Track and Joint System: Conform to IBC Chapter 7 including Section 702 and Section 713 for fire-resistive joint system as tested to UL 2079 or ASTM E1966.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Conform to provisions of Section 016600 and manufacturer's instructions.

B. Deliver in unopened containers or bundles, clearly labeled with manufacturer's name, brand, type, gauge/thickness, and grade. Verify undamaged conditions.

C. Store off the ground in dry well-ventilated space to protect from rusting and damage.

1.8 FIELD MEASUREMENTS

A. Verify field measurements with dimensions shown on Shop Drawings and manufacturer’s instructions.

1.9 COORDINATION

A. Conform to Section 013113 for coordination with related Sections.

B. Section 054000 for load bearing metal wall framing

C. Section 087100 for accommodating electric door strikes and other hardware items.

D. Section 078400 for firestopping installations prior to installation of gypsum board systems.

E. Section 092226 for suspended gypsum board ceiling systems.




PART 2 PRODUCTS

2.1 MANUFACTURERS

A. California Expanded Metal Products Co. (Cemco) 1. Tel (425) 591-4174, Fax (425) 413-1851, Email [email protected] (Aaron Rosin,

CSI) 2. Website www.cemcosteel.com

B. Dietrich Metal Framing 1. Tel (614) 840-4350, Fax (614) 840-4351, (Greg Ralph) 2. Website: www.dietrichindustries.com

C. SCAFCO Corporation 1. Tel (509) 343-9000, Fax (509) 343-9060 (Lawrence Stone) 2. Website: www.scafco.com

D. The Steel Network (TSN), Inc. 1. Tel (888) 474-4876, Fax (919) 845-1028, Email [email protected] (Howard

Sajecki) 2. Website http://www.steelnetwork.com

E. Steeler Inc. 1. Tel (800) 275-2279, (206) 725-2500, email [email protected] 2. Website www.steeler.com

F. Light Gauge Steel Framing: 1. Member of Steel Stud Manufacturers Association. 2. Accepted upon condition of satisfactory submittals referencing design requirements

and showing conformance to referenced ICC evaluation reports.

G. Substitution Requests: Submit for approval under provisions of Section 012500.

2.2 FRAMING MATERIALS

A. Refer to Section 054000 for load bearing members 20 gauge and over.

B. Non-Load Bearing - Light Gauge Framing Members: 1. ASTM C645, formed from steel meeting requirements of ASTM A568, ASTM A653

Grade 33. 2. Galvanized ASTM A653, G40 for interior conditions, except G60 where subject to

moisture exposure and at exterior walls. 3. Listed by ICC for structural design properties.

C. Steel Studs: 1. Minimum 33 mils (20 gauge). Provide higher gauge studs for greater design loads

conforming to manufacturer’s load tables. 2. Flanges: 1-1/4 inch, with 90-degree angle return leg 5/16 inches long. 3. Webs: Punched for mounting electrical conduit and cold rolled channel reinforcement.

D. Runners: Minimum thickness equal to stud gauge, except as otherwise indicated for top runners, minimum 1-1/4 inch flange, except as otherwise indicated for top runners.




E. Reinforcement for Metal Stud Framing Faced with Gypsum Board on One Side Only: 54 mils (16 gauge) minimum, 3/4 inch cold rolled channel, weighing 300 pounds per 1000 lineal feet, or 1-1/2 inch cold rolled channel, weighing 475 pounds per 1000 lineal feet.

F. Furring Channels: 1. Hat Channels: Minimum 33 mils (20 gauge), 1-3/8 inches wide, 7/8 inches deep,

hot-dip galvanized steel. 2. Z-Furring Channels: Minimum 33 mils (20 gauge), 1-1/2 inches deep, unless

otherwise specified, hot-dipped galvanized steel.

G. Sheet Metal Flat Strap Backing – Light Loads: Provided as alternative to 2 x dimensional lumber backing as specified Section 061000. For light loads such as toilet accessories. Not acceptable for heavy loads.

H. Sheet Metal Clipped Track Backing – Heavy Loads: Provided as alternative to Provide 2 x dimensional lumber backing as specified Section 061000. For heavy loads such as grab bars, handrails, wall hung cabinets. 1. Minimum 30 mils (20 gauge), 6 inches wide with 1-1/2 inch legs, notched and

continuous between studs designed for wall-supported items. 2. Minimum 54 mils (16 gauge) steel backing channel at loads exceeding 250 pounds

vertical point loading per fastener and as required for permanent support for heavier loads or loads where moment loads or torque is likely.

2.3 SOUND ISOLATION CHANNEL CLIPS AND CHANNEL SYSTEM

A. Manufacturers: 1. PAC International

a. Tel (866) 774-2100 / (503) 649-7700, Fax (503) 649-2710, Email [email protected] (Michael Gernhart, National Sales Mgr).

b. Website http://www.pac-intl.com 2. Kinetics Noise Control

a. Cell (206) 818-8840, Tel (425) 497-0660, Fax (425) 867-5542, (David Forrest, Seattle Sound and Vibration)

b. Website: www.seavib.com / http://kineticsnoise.com

B. Resilient Sound Isolation Clips: 1. PAC International, RSIC-1 Resilient Sound Isolation Clip, 7/8 inch hat channel mounted

to 54 mils (16 gauge clip) with rubber isolator for total 1-5/8 inch depth. 2. Kinetics IsoMax 7/8 inch hat channel mounted to 54 mils (16 gauge clip) with rubber

isolator for total 1-5/8 inch depth.

C. Furring Channel: 22 gage, 7/8 inch or 1-1/2 inch deep by 2-1/2 inch wide top by 1/1/4 inch wide bottom.

2.4 SOUND ISOLATION CHANNELS

A. Resilient Channels (RC-1): 1. 30 mils (25 gauge), 1/2 inch deep, hot-dip galvanized steel. 2. Pre-punched slotted fastener holes in flange 3/8 inch wide, 3 inch long, spaced 4 inch

on center. 3. Products:

a. Dietrich RC-Deluxe.




2.5 FASTENERS

A. Screw Fasteners: ASTM C1002 and C954, self-drilling, self-tapping framing, designed for type and gauge of framing. 1. Type G: Coarse pitch high thread for fastening gypsum board to gypsum board. 2. Type S: Fine thread for fastening gypsum board to cold formed steel members. 3. Type W: Coarse thread for fastening gypsum board to wood members. 4. Type A: Coarse pitch tapping screw for fastening metal plaster bases to wood or steel

members. 5. Type S-12: 18 gauge and heavier metal framing.

B. Anchorage Devices: Fasteners as required to transfer design loads. Powder actuated fasteners not permitted at overhead installations.

2.6 ACCESSORIES

A. Acoustical Sealant: As specified in Section 079200 and Section 092900.

PART 3 EXECUTION

3.1 EXAMINATION

A. Verify installation conditions as satisfactory to receive work of this Section.

B. Verify that rough-in utilities are in proper location.

3.2 PREPARATION

A. Meet at project site with the installers of related work including for hollow metal frames, mechanical, and electrical work. Review areas of potential interference and conflicts. Coordinate layout and make provisions for interfacing work.

B. Protect installed finish work of other trades and surfaces to preclude damage from work of this Section.

3.3 INSTALLATION

A. Install in accordance with manufacturer's instructions and provisions of Contract Documents.

B. Conform to ASTM C754 for installation of metal studs to receive gypsum board and other drywall systems.

C. At acoustic separation walls, place two beads of acoustical sealant between runners and substrate, studs and adjacent construction.

D. Isolation of Stud Systems from Structure: Where stud systems abut horizontal or vertical structural elements, isolate as required to prevent transfer of structural loads to light gauge framing systems.

E. Head of Wall Deflection Track: Install system designed to accept 1 inch deflection to prevent loading of non-load bearing wall framing.




1. Install at top of wall under structural steel deck and other systems and framing systems subject to deflection.

2. Firestop openings at fire-resistive construction under provisions of Section 078400 to close wall/ceiling penetrations through fire-resistive construction.

F. Nested Top Runner Systems: Accepted at non-fire resistive construction, based on Northwest Wall and Ceiling Bureau recommendations. Provide system as necessary to prevent sound transmission through acoustical wall systems.

G. Runner Tracks: 1. Layout and align tracks accurately at base and top of metal stud wall framing to make

plumb and true to line. 2. Butt runner tracks at partition corners and intersections, except leave clearance where

base course of gypsum board is to run through.

H. Steel Stud Wall Framing: 1. Erect studs not over 16 inch on center, unless otherwise indicated. Install additional

studs at partition intersections, corners, and as necessary to provide solid bearing for fasteners.

2. Construct corners using minimum three studs.

I. Door Openings: Install double boxed stud framing at openings.

J. Control and Expansion Joints: Install back to back studs. Conform to manufacturer’s and industry standards for control joints at fire rated walls. Coordinate with Section 092900 – Gypsum Board for locations of control joints.

K. Shimming and Bracing: 1. Shim metal furring to provide true and level surface for application of wallboard. 2. Cross brace chase partitions as recommended by manufacturer or accepted by

Architect. 3. Laterally brace metal studs to meet lateral design loads that have finish systems on one

side only or where finish systems do not run to full height of studs.

L. Install runner tracks and intermediate jack studs above and below wall openings to align with full-height wall stud spacing.

M. Bridging: Install lateral bridging as necessary to provide resistance to rotation and axial bending. Refer to NWCB requirements and SSMA Technical Note 2. 1. Walls supporting vertical (axial) loads and/or cladded only on one side:

a. Walls up to 10 feet height: Install two rows of bridging equally spaced. b. Walls over 10 feet height: Install bridging spaced 4'-0" maximum.

N. Sheet Metal Backing: Install continuous flat strap, steel channel or stud backing, notched between studs. Coordinate with requirements for support of wall mounted items including, casework, plumbing fixtures, mechanical equipment, door hardware, visual display surfaces, audio-visual equipment, and other items included in the Work.

O. Supplementary Framing: Install as necessary to accommodate loading conditions.

P. Resilient Channels: 1. Install per manufacturer’s instructions.




2. Fasten with 1-1/4 inch Type W screws for wood and 1-1/4 Type S screws for metal framing systems. Do not fasten with nails.

3. Overlap and nest and drive fasteners through both channel flanges into support framing. Do not butt channels.

4. Walls: a. Install with attachment flange facing down. b. Locate within 2 inch of floor and 6 inch from ceiling at 16 inch on center.

5. Ceilings: a. Install at right angles to framing system. b. Hold 1 inch clear of wall systems. c. Install into each framing member.

Q. Sound Retardant Partitions: Install acoustical sealant, between top and bottom runner tracks and adjacent material.

R. Install rubber closed cell closure strips, as specified in Section 053100, between top of stud partitions and preformed metal floor and roof deck as indicated to provide sound barrier between rooms.

3.4 ERECTION TOLERANCES

A. Maximum Variation From True Position: 1/8 inch in 10 foot.

B. Maximum Variation From Plumb: 1/8 inch in 10 foot.

3.5 REPAIR AND CLEANING

A. Repair or replace damaged studs and tracks.

B. Clean debris from tracks in preparation for drywall work. Do not allow any unexploded powder fasteners to be left in the tracks.

END OF SECTION


SECTION 092226SUSPENSION SYSTEMS


SECTION 092226 SUSPENSION SYSTEMS

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Interior suspended ceiling framing systems for support of screw attached interior

gypsum board ceilings.

B. Related Sections: 1. Section 061000 - Rough Carpentry 2. Section 052119 - Open Web Steel Joist Framing 3. Section 053100 - Steel Decking 4. Section 054000 - Cold-Formed Metal Framing 5. Section 092216 - Non-Structural Metal Framing 6. Section 092900 - Gypsum Board 7. Division 21 - Fire Suppression 8. Division 23 - Heating, Ventilating, and Air Conditioning 9. Division 26 - Electrical


A. Steel Channel Ceiling Suspension System: Cold-formed steel main support channels, lateral support channels and furring channels supported by hanger wire to structural support.

B. Pre-engineered Suspended Tee Bar Suspension System: Curved and flat ceiling interlocking main tees and cross tees as option to steel channel ceiling suspension system.

1.3 REFERENCES


B. American Society for Testing and Materials (ASTM) International: 1. ASTM A568 - General Requirements for Steel, Sheet, Carbon and High-

Strength, Low-Alloy, Hot-Rolled and Cold-Rolled. 2. ASTM C635 - Specification for Metal Suspension Systems for Acoustical

Tile and Lay-in Panel Ceilings. 3. ASTM C636 - Practice for Installation of Metal Ceiling Suspension Systems

for Acoustical Tile and Lay-in Panels. 4. ASTM C645 - Standard Specification for Non-Load (Axial) Bearing Steel

Studs, Runners (Track) and Rigid Furring Channels for Screw Application for Gypsum Board.

5. ASTM A653 - Standard Specification for Steel Sheet, Zinc Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvanized) by the Hot-Dip Process.

6. ASTM C754 - Standard Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum.

7. ASTM C954 - Standard Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases




to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness

8. ASTM C1002 - Specification for Steel Drill Screws for the Application of Gypsum Board.

C. Ceiling and Interior Systems Contractors Association (CISCA): Ceiling Systems Installation Handbook.

D. Northwest Wall and Ceiling Bureau (NWCB), Tel (206) 524-4243 (Mark Fowler, Bob Drury). 1. NWCB 400-102 - Suspended Ceilings. 2. NWCB 400-200 - Suspended Gypsum Board or Cement Board Ceilings.

1.4 SUBMITTALS

A. Submit under provisions of Section 013300.

B. Product Data: Manufacturer’s catalog cuts describing standard framing systems, components, finishes, product criteria, load charts, and limitations.

C. Manufacturer's Instructions: Include installation instructions, rough-in dimensions, special procedures, and perimeter conditions requiring special attention.

D. Design Data: Seismic sway bracing in conformance to Code, and ICC Evaluation Services Evaluation Report or approval for steel framing systems showing load and deflection criteria, correlated to gypsum board materials specified.

1.5 QUALITY ASSURANCE

A. Suspended Gypsum Board Installations: Perform work of this Section and Section 092900 by or under direct supervision of single installer.

1.6 QUALIFICATIONS

A. Installer: Company specializing in work of this section with minimum 3 years documented experience. Recommended by Northwest Wall and Ceiling Bureau prior to submitting Bid, or accepted by Architect.


A. Conform to requirements of Section 014100 for referenced Codes, ordinances, and other regulatory requirements.

B. Framing Systems: Listed by ICC ES Evaluation Report for structural design properties.

1.8 COORDINATION

A. Conform to Section 013113 for coordination with work of other Sections.

B. Section 053100 for support of hanger wire from structural steel deck prior to placement of concrete topping.




C. Section 054000 and Section 092216 for tying into metal framing systems.

D. Section 061000 for tying into wood framing systems.

E. Section 092900 as suspension framing for gypsum board ceiling systems.

F. Division 21, Division 23, and Division 26 for location, installation, support, and access to equipment and fixtures including fire sprinkler systems, lighting fixtures, and other required penetrations.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Steel Channel Ceiling Suspension System: As specified this Section.

B. Pre-Engineered Tee Bar Ceiling Suspension System: 1. Armstrong World Industries, Drywall Grid Systems

a. Cell (206) 919-0438, Voice Mail (877) 276-7876 Option 8 Ext 8143, Fax (253) 862-4775, Email [email protected] (Tim Hamilton CSI).

b. Website http://www.armstrong.com 2. USG Corporation, Drywall Suspension System

a. Cell (425) 468-9355, Fax (425) 888-5355, Voice Mail (800) 874-8880 Ext 6750, Email [email protected] (Scott Finlinson),

b. Website http://www.usg.com 3. BPB Celotex, Drywall Grid System:

a. Cell (253) 219-5725, Tel (360) 893-1514 (Home), Tel (800) 523-4684, Voice Mail (866) 8721, Fax (360) 893-1514, Email [email protected] (Bob Sagehorn, CSI).

b. Website www.celotex.com / www.bpb.com 4. Chicago Metallic Corp., Drywall Grid System

a. Tel (425) 277-0631, Fax (425) 277-5446, Email [email protected] (Schwarz & Associates, Andy Schwarz / Cell (206) 218-3489, Email [email protected] Jerald Schwarz)

b. Website http://www.chicagometallic.com

C. Substitution Requests: Submit for approval under provisions of Section 012500.

2.2 MATERIALS

A. Cold Rolled Steel: ASTM C645, conforming to ASTM A568 Grade 33 or ASTM A653 Grade 33. 1. Typical: Galvanized ASTM A653 G40. 2. Exterior Installations: Galvanized ASTM A653 G 60. 3. Swimming Pool Areas and other High Humidity Areas: Galvanize ASTM A653 G90.

2.3 STEEL CHANNEL CEILING SUSPENSION SYSTEM

A. Main Support Carrying Channels: Cold-rolled steel, 16 gauge (0.053 inch) by 1-1/2 inch deep.




B. Intermediate Lateral Support Runners: Cold-rolled steel, 16 gauge (0.053 inch) by 3/4 inch deep.

C. Furring Channels: Hat channels, 2-9/16 inch wide by 7/8 inch deep, minimum 20 (0.033 inch) gauge, rolled formed steel, and as required by loading and deflection tolerances, except 18 gauge minimum at exterior installations.

2.4 TEE BAR CEILING SUSPENSION SYSTEM

A. Straight Main Tees: 1-1/2 inch face width, 1-1/2 inch high by 144 inch long. Integral reversible splice with knurled face.

B. Cross Tees: 1-1/2 inch high, 48 inch long, 1-1/2 wide face. Integral reversible splice with knurled face. Quick release for positive locking and removal without need for tools.

C. Furring Channels (as applicable): 7/8 inch high, 48 inch ling, 1-7/16 inch face.

2.5 ACCESSORIES

A. Hanger Wire: 1. Minimum 12 gauge galvanized soft annealed wire, as accepted by ICBO Evaluation

Report ER-4071 and NWCB 400-200 recommendations. 2. Minimum 9 gauge galvanized soft annealed wire at double layer gypsum board,

equipment loading, and as required to limit deflection to L/360.

B. Tie Wire: 18 gauge galvanized soft annealed steel wire.

C. Furring Channel Clips: Manufacturer's standard galvanized wire, designed to attach furring channels to 1-1/2 inch cold rolled channels.

D. L-Type Runners: Minimum 24 gauge, 1 inch by 1 inch cold rolled galvanized steel.

E. Channel Molding: Minimum 24 gauge, 1-1/2 inch by 1 inch cold rolled galvanized channel.

F. Fastening Devices at Ceiling for Suspension: Conform to ASTM C754 and as instructed by manufacturer and NWCB.

G. Screw Type Fasteners: ASTM C1002 and C954, self-drilling, self-tapping framing screws, designed for gauge of framing.

PART 3 EXECUTION

3.1 EXAMINATION

A. Verify conditions ready to receive work of this Section before beginning.

B. Verify that work above ceiling suspension systems is complete, including fire protection, mechanical and electric systems, and installed in manner that will not adversely affect layout and installation of work of this Section.




3.2 STEEL CHANNEL CEILING SUSPENSION SYSTEM

A. Conform to manufacturer's instructions and provisions of Contract Documents.

B. Carrying Channel Runners: 1. Secure 1-1/2 cold rolled channel with hanger wire to overhead construction. 2. Space hanger wire and carrying channels not to exceed 4 foot on center each way,

except where intermediate spacing is required to meet loading capacity and deflection tolerances.

C. Furring Channels: Wire tie or clip hat channels to carrying channel runners spaced at 16 inch on center.

D. Install L-channel at perimeter of suspension system to provide continuous support for fastening gypsum board and plaster ceiling finishes.

E. Install additional carrying channels and furring channels to accommodate duct work, lighting fixtures, and other ceiling penetrations where needed for intermittent support.

3.3 TEE-BAR CEILING SUSPENSION SYSTEM

A. Install in accordance with manufacturer's instructions and provisions of Contract Documents. Where in conflict, verify with Architect before beginning work.

B. Conform to ASTM C636, CISCA installation standards, NWCB recommendations, UL Fire Resistance Directory, and other Regulatory Requirements for code compliance.

3.4 Flat Ceilings: 1. Space main tees at maximum 48 inch on center. 2. Support from hanger wire directly to structure above. 3. Space at maximum 48 inch on center. 4. Space cross tees at maximum 16 inch on center and as required to conform to UL.

B. Accessories: Install wall angles, channel molding, furring channel, attachment clips, transition clips, splice clips, as instructed by manufacturer for system assembly.

C. Install additional hanger wire, main tees, cross tees, and accessories as necessary to stabilize and complete system assembly 1. Maintain visually acceptable gypsum board planes and corners free of telegraphing and

visual surface defects. 2. Accommodate duct work, lighting fixtures, and other ceiling penetrations where

needed for intermittent support.

3.5 CONTROL JOINTS

A. Install control joints with framing members broken or spliced at spans exceeding 50 lineal foot or exceeding 2500 square foot overall if not indicated on Drawings.

B. Do not contact abutting construction such as walls and columns.

C. Seal with foam tape or joint sealant.




3.6 INSTALLATION TOLERANCES:

A. Maximum Variation From Level: 1/8 inch in 12 feet.

B. Maximum Deflection for Suspension System: L/360 of span.

END OF SECTION


SECTION 092800BACKING BOARDS AND UNDERLAYMENTS


SECTION 092800 BACKING BOARDS AND UNDERLAYMENTS

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Underlayment to interior tile wall systems

B. Related Sections: 1. Section 061000 - Rough Carpentry 2. Section 054000 - Cold-Formed Metal Framing 3. Section 092216 - Non-Structural Metal Framing 4. Section 092900 - Gypsum Board 5. Section 093000 - Tile


A. Conform to Tile Council of America (TCA) Methods and provisions of Section 093000 for backing board types and use.

1.3 REFERENCES


B. American National Standards Institute (ANSI): 1. ANSI A118.4 - Latex-Portland Cement Mortar. 2. ANSI A118.9 - Cementitious Backer Units.

C. American Society for Testing and Materials (ASTM) International: 1. ASTM C954 - Standard Specification for Steel Drill Screws for the

Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness

2. ASTM C1002 - Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs.

3. ASTM C1178 - Specification for Glass Mat Water-Resistant Gypsum Backing Panel

4. ASTM C1278 - Specification for Fiber Reinforced Gypsum Panels 5. ASTM C1288 - Standard Specification for Discrete Non-Asbestos Fiber-

Cement Interior Substrate Sheets. 6. ASTM C1325 - Standard Specification for Non-Asbestos Fiber-Mat

Reinforced Cement Substrate Sheets. 7. ASTM E119 - Test Methods for Fire Tests of Building Construction and

Materials 8. ASTM E136 - Standard Test Method for Behavior of Materials in a Vertical

Tube Furnace at 750 Degrees C.

D. Tile Council of America (TCA): Handbook for Ceramic Tile Installation.




1.4 SUBMITTALS


B. Product Data: Manufacturer's descriptive literature indicating material composition, thickness, sizes, and fire resistance for the following. 1. Backing board 2. Fasteners 3. Joint tape 4. Joint compound

C. Manufacturer's Instructions: Include installation requirements and conditions requiring special attention.



B. Deliver in manufacturer’s unopened protective packaging with manufacturer’s identifying label intact.

C. Store inside, under cover, protected from moisture, soiling, and damage. Lay sheets flat. Do no stand on edges.

1.6 COORDINATION


B. Section 092900 and 093000 for tile backing board tie into gypsum board systems.

PART 2 PRODUCTS

2.1 BACKING BOARD MANUFACTURERS

A. Custom Building Products, Wonderboard. 1. Tel (800) 246-5177 / (206) 762-6620, Direct Line (206) 767-2265, Fax (206) 768-

2816, Pager (800) 730-1145, Email [email protected] (Chuck Hill, Mfrs Rep) 2. Cell (209) 518-1153, Fax (209) 477-6752, Email [email protected] (John Gallup,

CTC, CSI Architectural Consultant). 3. Cell (206) 250-4675, Fax (425) 254-9262, Email [email protected] (Bob McCall, CTC,

NW Territory Mgr) 4. Website custombuildingproducts.com

B. CertainTeed (CT) (formerly BPB America, Inc. (BPB)) 1. Cell (425) 894-7784, Fax (206) 768-3792, Email [email protected] (Mark

Salmon, Sales Rep). 2. Cell (206) 852-5307, Tel (206) 768-3776, Email [email protected] (David

Moles, Reg Sales Mgr) 3. Website: www.bpb-na.com

C. Georgia Pacific, Corp. (G-P) 1. Tel (206) 781-6525, Email [email protected] (Mike Fletcher)




2. Website www.gpgypsum.com 3. Technical Services: (800) 225-6119

D. James Hardie Building Products, Inc. 1. Cell (206) 251-2982, Email [email protected] (Nate Haugen,

Hardiebacker Rep). 2. Website www.jameshardie.com.

E. U. S. Gypsum Co. (USG) 1. Cell (425) 468-9355, Fax (425) 888-5355, Voice Mail (800) 874-8880 Ext 6750, Email

[email protected] (Scott Finlinson CSI, Mfrs Rep). 2. Website www.usg.com

F. Temple-Inland 1. Cell (972) 467-3499, email: [email protected] (Glenn Miller) 2. Website: www.templeinland.com 3. Tel (206) 226-2311, (425) 277-0506, email: [email protected] (Dave Sommer) 4. Website: www.interra-facades.com

G. Knauf products not accepted.

H. Substitution Requests: Submit for approval under provisions of Section 012500.

2.2 GLASS MATT FACED GYPSUM BACKING BOARD

A. Glass Matt Faced Gypsum Backing Board: Conforming to ASTM C1178. 1. Non-Fire Rated: 1/2 inch thick or 5/8 inch thick as required to flush out with gypsum

board. 2. Fire Resistant: 5/8 inch thick, Type X, tested to ASTM E119, UL Classified.

B. Products: 1. Georgia Pacific, Corp. (G-P), Dens-Shield Tile Backer 2. CertainTeed (CT) (formerly BPB America, Inc. (BPB)), Backer Board Type X.

2.3 FIBER-CEMENT BACKING BOARD

A. Fiber Cement Backing Board and Underlayment: Portland cement, ground sand, cellulose fiber reinforced, autoclaved cement board, conforming to ASTM C1288. Non-combustible, conforming to ASTM E136. 1. Walls: 1/2 inch thick

a. James Hardie, Hardiebacker 500

2.4 GLASS-FIBER REINFORCED CEMENT BACKING BOARD

A. Glass Fiber Reinforced Cementitious Backing Board: Portland cement based, glass fiber mesh reinforced tile backing board, square or tapered edge, conforming to ASTM C1325 or ANSI A118.9. 1. Walls: 1/2 inch thick or 5/8 inch thick as required to flush out with gypsum board.

B. Products 1. U.S. Gypsum Corp., (USG), Durock 2. National Gypsum Company (NG), PermaBase Cement Board




3. Custom Building Products, Wonderboard. 4. C-Cure, C-Cure Board 990. 5. CertainTeed Corp.; FiberCement BackerBoard.

2.5 ACCESSORIES

A. Trim: Sheet Steel zinc coated by hot-dip process and as specified Section 092900.

B. Screw Fasteners: Conforming to ASTM C1002 and C954, self embedding bugle head and corrosion resistant coating, and as instructed by manufacturer. 1. Length: As required to penetrate minimum 3/8 inch into steel framing and 1-1/4 inch

into wood framing. 2. 20 Gauge Metal Framing: Type S 3. 18 Gauge or Heavier Metal Framing: Type S-12 Conforming to ASTM C954.

C. Filler: Pre-sanded dry-set or latex Portland cement mortar.

D. Joint and Corner Tape: Self adhesive, 2 inch wide, polymer-coated, open alkali-resistant glass-fiber mesh and as instructed by manufacture. Paper tape not accepted. 1. BPB Marco Fiberglass Drywall Mesh Tape

E. Joint Compound: Chemically curing type. Drying type joint compound not accepted. 1. Georgia Pacific, Speed Set 2. USG Sheetrock Easy Sand or Durabond 3. Beadex, Silver Set 4. BPB Profin Lightweight Setting Compound

F. Adhesives/Mortar Products: Latex Cement Mortar: ANSI A118.4 and as instructed by manufacturer for condition of use.

G. Joint Sealant: As specified Section 079200 and TCA E117.

PART 3 EXECUTION

3.1 EXAMINATION

A. Verify that conditions are ready to receive work of this Section before beginning. If not, notify Architect.

B. Verify framing substrate plumb, level, and solid with stud spacing maximum 16 inch on center and suitable for supporting and installing work of this Section.

C. Verify adjacent finishes as appropriate for application of work of this Section.

3.2 PREPARATION

A. Furr or shim as required to bring adjacent finished surfaces into flush alignment.

3.3 INSTALLATION





B. Screw to metal stud framing members at maximum 8 inch on center over stud framing spaced at maximum 16 inch on center. Set screw heads flush.

C. Fill fastening depressions and joints with specified organic adhesive or latex cement mortar for smooth, uniform surface free of cracks, depressions, and broken edges

D. Immediately embed glass-fiber mesh tape at joints and corners into organic adhesive or latex cement mortar and trowel smooth and level to face of panel.

E. Install additional fasteners and perform work as required to provide solid, firm substrate for tile installations specified Section 093000.

F. Seal joints and openings around pipes, fittings, and fixtures with water proof flexible joint sealant. 1. Allow areas to dry thoroughly prior to tile application. 2. Wipe excess material from surface of panels.

3.4 ADJUSTING

A. Remove and reinstall defective and damaged work. Leave ready as suitable substrate for installation of tile.

END OF SECTION


SECTION 092900GYPSUM BOARD


SECTION 092900 GYPSUM BOARD

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Gypsum board wall and ceiling systems. 2. Trim accessories, Joint compound, control joints, fasteners, and sealants. 3. Level of finish for gypsum board surfaces.

B. Related Sections: 1. Section 054000 - Cold-Formed Metal Framing 2. Section 061000 - Rough Carpentry 3. Section 061643 - Gypsum Sheathing 4. Section 072116 - Blanket Insulation 5. Section 078400 - Firestopping 6. Section 079200 - Joint Sealants 7. Section 092216 - Non-Structural Metal Framing 8. Section 092226 - Suspension Systems 9. Section 092800 - Backing Boards and Underlayment 10. Section 099000 - Painting and Coating

1.2 REFERENCES


B. American Society for Testing and Materials (ASTM) International: 1. ASTM C475 - Standard Specification for Joint Compound and Joint Tape

for Finishing Gypsum Board. 2. ASTM C834 - Standard Specification for Latex Sealants 3. ASTM C840 - Standard Specification for Application and Finishing of

Gypsum Board. 4. ASTM C919 - Standard Practice for Use of Sealants in Acoustical

Applications. 5. ASTM C954 - Standard Specification for Steel Drill Screws for the

Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness.

6. ASTM C1002 - Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs.

7. ASTM C1047 - Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base.

8. ASTM C1278 - Standard Specification for Fiber-Reinforced Gypsum Panel. 9. ASTM C1396 - Standard Specification for Gypsum Board. 10. ASTM C1658 - Standard Specifications for Fiberglass Mat Gypsum Panels. 11. ASTM C1629 - Standard Classification for Abuse-Resistant Nondecorated

Interior Gypsum Panel Products and Fiber-Reinforced Cement Panels.

12. ASTM D3273 - Standard Test Method for Resistance to Growth of Mold on




the Surface of Interior Coatings in an Environmental Chamber.

13. ASTM E90 - Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements.

C. Gypsum Association (GA): Website http://www.gypsum.org/ 1. GA-201 - Gypsum Board for Walls and Ceilings. 2. GA-214 - Recommended Levels of Levels of Gypsum Board Finish. 3. GA-216 - Specifications for the Application and Finishing of Gypsum

Board. 4. GA-226 - Application of Gypsum Board to Curved Surfaces. 5. GA-235 - Gypsum Board Typical Mechanical and Physical Properties. 6. GA-236 - Joint Treatment under Extreme Weather Conditions. 7. GA-238 - Guidelines for Prevention of Mold Growth on Gypsum

Board. 8. GA-600 - Fire Resistance Design Manual. 9. GA-801 - Handling and Storage of Gypsum Panel Products: A Guide

for Distributors, Retailers, and Contractors

D. Northwest Wall and Ceiling Bureau (NWCB), Tel (206) 524-4243 (Bob Drury and Mark Fowler) Email: [email protected], Website http://www.nwcb.org . 1. NWCB 300-100 - Guide Specification for Gypsum Wallboard. 2. NWCB 300-101 - Recommended Applications of Gypsum Board. 3. NWCB 300-102 - Installation of Gypsum Board for Fire Rated Partitions. 4. NWCB 300-103 - Field Technical Information – Gypsum Wallboard and

Winter Weather. 5. NWCB 300-104 - Installation of Control Joints in Interior Construction. 6. NWCB 300-105 - Installing Corner Trim for Gypsum Wallboard or Veneer

Plaster. 7. NWCB 300-300 - Recommended Procedure for Judging Gypsum Wallboard. 8. NWCB 300-301 - Recommended Levels for Finishing of Gypsum Board.

E. UL Fire Resistance Directory (UL): Fire Resistance Volume 1 – with Hourly Ratings for Beams, Floors, Roofs, Columns, Walls and Partitions.

1.3 SUBMITTALS


B. Product Data: Manufacturer's published descriptive literature for gypsum board types, trim accessories, and control joints pertinent to this Section.

C. Test Data: UL or WHI Design for each proprietary fire-resistive wall and ceiling assembly listing manufacturers and products. Unlisted manufacturers and products not accepted.


A. Installer: 1. Company specializing in work of this section with minimum 5 years documented

experience in commercial quality work of comparable scope. 2. Recommended as qualified installer by NWCB prior to Bid, or accepted by Architect.




B. Single Source Responsibility: 1. Perform work by or under direct supervision of the same installer. 2. Provide gypsum board products, listed in this Section, from the same manufacturer.


A. Conform with Section 014100 for code compliance requirements related to this Section.

B. Conform to requirements for tested fire rated assemblies. 1. GA 600, Fire Resistance Design Directory. 2. UL, Fire Resistance Directory, or Intertek Testing Services (WHi). 3. IBC Chapter 25, including Section 2506, 2508, 2509 and related tables. 4. ICC Evaluation Reports and Standards.

1.6 MOCK-UPS

A. Provide in accordance with Section 014300.

B. Install 100 square foot minimum mock-ups of each gypsum board finish and control joints.

C. Approved mock-ups may be incorporated into Work and become standard for approved workmanship and finishes.

1.7 PRE-INSTALLATION CONFERENCE

A. Arrange, in accordance with Section 013119 two weeks prior to beginning work of this Section.

B. Walk job and determine full extent level of quality for work.


A. In accordance with Section 016600, GA-238, GA-801, and manufacturer's instructions.

B. Deliver materials in original unbroken containers or bundles bearing name of manufacturer and brand.

C. Verify products undamaged before acceptance at Project Site. Do not use products with visible signs of mold growth and damage.

1.9 ENVIRONMENTAL REQUIREMENTS

A. Temperature, Ventilation and Moisture: Conform to NWCB 300-103 and manufacturer’s instructions. Maintain temporary controls to regulate heating, ventilating, moisture, and humidity levels. Do not begin taping and finishing until following conditions are achieved. 1. Building: Fully enclosed and free of standing water. Watertight roofing and wall

envelope systems in place. 2. Temperature: Between 50 and 95 degrees F for minimum 48 hours. 3. Relative Humidity: Less than 65 percent. 4. Gypsum Board Moisture Content: 0.4 percent on gypsum scale (12 percent on wood




scale). 5. Wood Substrate Moisture Content: Maximum 16 percent.

B. Lighting: Sufficient temporary lighting to perform work to achieve specified finishes.

1.10 COORDINATION


B. Coordinate with Wall Type Schedule, Section 061643 for gypsum sheathing, Section 092800 for backing boards, and for gypsum board systems used in conjunction with work of this Section.

C. Coordinate with Section 092216 for nonstructural metal framing and Section 092226 for suspension systems.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. United States Gypsum Corp. (USG) 1. Cell (425) 468-9355, Email [email protected] (Scott Finlinson). 2. Website: www.usg.com

B. Georgia Pacific Corp. (G-P) 1. Tel (206) 781-6525, Email [email protected] (Jeff Herrmann),

[email protected] (Mike Fletcher) 2. Website: www.gpgypsum.com 3. Tel (800) 225-6119 Technical

C. CertainTeed (CT) formerly BPB America, Inc. (BPB) 1. Cell (425) 894-7784, Fax (206) 768-3792, Email [email protected] (Mark

Salmon, Sales Rep). 2. Cell (206) 852-5307, Tel (206) 768-3776, Email [email protected] (David

Moles, Reg Sales Mgr) 3. Website: www.bpb-na.com

D. National Gypsum Company (NGC) 1. Tel (360) 260-4896, Pager (800) 608-4235, Fax (360) 260-0019, Email

[email protected] (Jim Flyr, Sales Rep) 2. Tel (800) 824-4227, Fax (800) 438-6266 (Western Service Sales Area) 3. Tel (800) 628-4662, Fax (800) 329-6421(Technical Assistance, Home Office) 4. Website: www.nationalgypsum.com

E. Temple-Inland 1. Cell (972) 467-3499, email: [email protected] (Glenn Miller) 2. Website: www.templeinland.com 3. Tel (206) 226-2311, (425) 277-0506, email: [email protected] (Dave Sommer) 4. Website: www.interra-facades.com

F. Knauf products not accepted.




G. Substitution Requests: Submit for approval under provisions of Section 012500.

2.2 PAPER FACED GYPSUM PRODUCTS

A. Fire Rated Gypsum Board: ASTM C1396, tapered edges, 5/8 inch, Type X core, paper faced. 1. Meet or exceed Type X. UL labeled and ICC ES approved for fire resistive systems. 2. Products:

a. Temple-Inland, Type X b. Georgia-Pacific, ToughRock Fireguard Type X c. USG, Sheetrock Firecode X d. National Gypsum, Gold Bond Fire-Shield Wallboard e. Certainteed, ProRoc Type X

B. Fire Rated Mold and Moisture Resistant Gypsum Board: ASTM C1396, 5/8 inch thick, tapered edge, Type X core. Mold resistance score of 10 when tested in accordance with ASTM D 3273. 1. Temple-Inland, ComfortGuard Type X 2. Georgia-Pacific, Mold-Guard Type X 3. USG, Mold Tough Firecode Core 4. National, XP Fire-Shield Gypsum Board 5. Certainteed, ProRoc Type X w/ M2 Tech

C. Tile Backing Board: As specified Section 092800.

2.3 JOINT TREATMENT MATERIALS

A. General: Comply with ASTM C475 and as recommended by gypsum board manufacturer for intended purpose.

B. Joint Tape: 1. Paper Tape: Manufacturer’s standard 2 inch wide 2. Fiberglass Tape: Not accepted for interior gypsum board products specified in this

section.

C. Joint Compound: Manufacturer’s standard powder or premix drying type regular or light weight. At locations where Mold and Moisture Resistant Gypsum Board is indicated, use regular weight joint compound.

D. Prefilling Compound (if required for gaps and damage): 1. NGC; Sta-Smooth Brand Joint Compound, setting type. 2. USG; Sheetrock or Beadex Brand Setting-Type Brand Taping Joint Compounds 3. Substitution Requests: Submit for approval under provisions of Section 012500.

E. Embedding Compound – First Coat: 1. NGC; ProForm Brand All Purpose Joint Compound, drying type. 2. USG; Sheetrock or Beadex Brand Taping Joint Compound Ready-Mixed 3. Substitution Requests: Submit for approval under provisions of Section 012500.

F. Fill Compound - Second Coat: 1. NGC; ProForm Brand All Purpose Joint Compound, drying type. 2. USG; Sheetrock or Beadex Brand All Purpose or Topping Joint Compound Ready-




Mixed 3. Substitution Requests: Submit for approval under provisions of Section 012500.

G. Finishing Compound – Third Coat: 1. NGC; ProForm Brand All Purpose Joint Compound, drying type. 2. USG; Sheetrock or Beadex Brand All Purpose or Topping Joint Compound Ready-

Mixed 3. Substitution Requests: Submit for approval under provisions of Section 012500.

H. Skim Coat – Level 5 Final Coat: 1. NGC; ProForm Brand All Purpose Joint Compound, drying type; ProForm Brand

Surfacer/Primer. 2. USG; Sheetrock or Beadex Brand All Purpose Ready-mixed Joint Compound or USG

Tuff-Hide Primer/Surfacer in lieu of skim coat. 3. Substitution Requests: Submit for approval under provisions of Section 012500.

2.4 ACCESSORIES

A. Thermal insulation: As specified Section 072116.

B. Joint Sealant at Exposed Joints: Paintable, Non-setting, non-staining, and as specified Section 079200.

C. Acoustical Sealant at Exposed Joints: As specified in Section 079200. 1. Nonsag, paintable, nonstaining, latex sealant conforming to ASTM C834. Tested to

ASTM E90 for reduction of airborne sound transmission through perimeter joints and openings in building construction at representative assemblies. Specified for type and quality: a. Pecora; AC-20 FTR Acoustical and Insulation Sealant b. USG, SHEETROCK, Acoustical Sealant c. Substitution Requests: Submit for approval under provisions of Section 012500.

D. Acoustical Sealant at Concealed Joints: As specified in Section 079200. 1. Synthetic Rubber Joint Sealant: Single component, non-skinning, non-hardening, 90

percent solids, acoustical properties conforming to ASTM E90. a. Pecora, BA-98 b. Tremco, Acoustical Sealant c. Substitution Requests: Submit for approval under provisions of Section 012500.

2. Water Based Siliconized Acrylic Latex: a. Pecora, AIS-919 b. USG, SHEETROCK, Acoustical Sealant c. Substitution Requests: Submit for approval under provisions of Section 012500.

3. Install 2 beads under steel stud framing channel and wood plates and into 1/2 inch space between top of floor and bottom of gypsum board and plaster systems.

E. Laminating Adhesive: Adhesive or joint compound recommended for directly adhering gypsum panels to continuous substrate. 1. Use adhesives that have a VOC content of 50 g/L or less when calculated according

to 40 CFR 59, Subpart D (EPA Method 24).

F. Firestopping and Smoke Sealants: As specified Section 078400.




2.5 TRIM

A. Provide trim shapes as required to cover and make neat edges.

B. Paper Faced Metal Bead and Trim: ASTM C1047, electro-galvanized steel with paper face and flanges, USG Beadex specified for type and quality. 1. Outside corner beads 2. Inside corners. 3. L-type edge trim. 4. J-shaped edge trim

2.6 FASTENERS

A. Screws: Conforming to ASTM C1002 and C954. Bugle or pan head, and lengths as required for securing materials in place. Minimum 3/4 inch penetration at wood and steel studs. 1. Wood Framing and Backing: Type W. 2. Light Gauge Metal Framing: Type S. 3. 18 Gauge or Heavier Metal Framing: Type S-12 and conforming to ASTM C954.

PART 3 EXECUTION

3.1 EXAMINATION

A. Verify installation conditions as satisfactory to receive work of this Section before beginning.

B. Verify framing systems, including backing, insulation, vapor barriers, work of Division 21, 22, 23 and 26, and other systems ready for work of this Section.

C. Verify work of Section 054000, Section 072116, Section 092216, and Section 092226 for metal framing, insulation installation, and vapor barrier requirements prior to beginning work of this Section.

D. Verify building fully enclosed and dry. 1. Do not begin work until building envelope is fully enclosed and temperature,

ventilation, and humidity are controlled. 2. Do not begin work under conditions that gypsum board installation may be exposed

to water contact.

3.2 PREPARATION

A. Protect surrounding areas and surfaces to preclude damage.

B. Avoid soiling, spatter, and damage to work of other trades. Use cover cloths, or other means of protection. Remove, clean, and repair soiled or damaged work.

3.3 INSTALLATION

A. Conform to ASTM C840, GA-216, NWCB 300-101, NWCB 300-102, NWCB 300-103, NWCB 300-105 and manufacturer's instructions.




3.4 BOARD INSTALLATION

A. Panel Joints: 1. Layout: Design to reduce joints to minimum. 2. Install board in maximum lengths to minimize horizontal and vertical joints. 3. Start installation of panels at exterior wall to position butt joints as far away from

exterior wall as possible. 4. Place edges in contact and fit neatly, without forcing into place. 5. Stagger joints on opposite sides of partitions and on same side of wall surface at

adjacent joints. 6. Maintain minimum 1/4 inch clearance from bottom of wall panel and top of floor.

Seal with acoustical sealant. 7. In order to prevent wicking of moisture, do not let gypsum board rest on floor after

installation.

B. Single Layer Systems: Install in accordance with ASTM C840. Where modified, amended, or required by fire resistive or sound isolation system, conform to the requirements of the manufacturer's tests, as approved.

C. Double Layer Systems: Install in accordance with ASTM C840, including System VIII for double layer gypsum wallboard installations applied with screws. Conform to required fire resistance standards.

D. Tile Backing Board: Install under provision of Section 092800 behind tile wall installations. Moisture resistant (green board) gypsum board is not accepted as backing for tile.

E. Joint Sealant and Acoustical Sealant: Install to completely fill void between wallboard edges and adjacent surface.

3.5 ACOUSTICAL SEALANT

A. Apply in accordance with sealant manufacturer’s instructions.

B. Apply 1/4 inch minimum 1/2 inch maximum bead of sealant to seal perimeter of sound-rated partitions.

C. Seal sound-rated partitions 1. on both sides where facings abut dissimilar materials 2. around perimeter, in the angle formed by panels and abutting dissimilar materials 3. at all intersections 4. at all panel terminations in door and window frames 5. at control joint locations before attaching the control joint to the panels.

D. Apply continuous beads of sealant around all openings formed for outlets, lights, etc. Completely butter the outside of electrical boxes.

E. Cut gypsum panels with 1/8 inch maximum relief at perimeter to receive sealant. Install before sealant skins.

3.6 FIRESTOPPING




A. Firestopping and Smoke Sealants: Install in accordance with Section 078400.

B. Mechanical and Electrical: Coordinate with Division 21 through Division 28. Provide for installations and penetrations of ductwork, equipment, receptacles, and other work.

3.7 TRIM INSTALLATION

A. Corner Trim: Reinforce external corners with specified corner beads.

B. Edge Trim: Install square edged metal trim bead at exposed edges and boundaries of areas and where abutting dissimilar materials.

C. Reveal Trim: 1. Install with screws at 12 inch on center in 10 foot lengths, except where shorter

lengths are sufficient for dimension of wall plane. 2. Make butt joints tight and in alignment. 3. Miter corners. 4. Promptly remove excess joint compound.

D. Other Trim: Install as indicated or required for complete and finished installation.

3.8 CONTROL JOINT INSTALLATION

A. Control Joints: Conform to NWCB 300-104 and GA-234, except as otherwise indicated. Verify that required double framing is in place before installing control joints. 1. Door and Relite Openings: Install control joints at each side of door and relite

opening and at both sides of wall, except alcoves and similar wall configurations. 2. Continuous Wall Planes: Not to exceed 30 lineal foot. Area not to exceed 300

square feet. 3. Ceilings: Not to exceed 50 lineal foot. Area not to exceed 2500 square foot. 4. Joints with Other Materials: Install where gypsum board meets other materials such

as masonry, concrete, plaster, and veneer plaster, except where joint is concealed under horizontal chair rail or other trim.

5. As indicated at other locations on Drawings.

3.9 TRIM AND JOINT FINISHING

A. Joints and Interior Angles: Embed tape in joint compound and apply three separate coats of joint compound over joints, angles, fastener heads, and accessories. Tool joint compound smooth and free of tool marks and rides. 1. Center reinforcing tape over joint and coat into compound leaving approximately

1/64 inch to 1/32 inch under tape to provide proper bond. 2. Follow with skim coat to embed tape, but not to function as second coat. 3. Allow embedding coat to thoroughly dry prior to application of second coat. 4. Allow second coat to thoroughly dry. 5. Apply third coat evenly over and extending beyond second coat on joints, feathering

to smooth uniform finish.

B. Beads, Trim, Fastener and Joint Depressions: 1. Cover with three coats of taping and joint compound. Apply in different directions

making smooth transitions with adjacent surfaces. 2. Allow sufficient drying time between coats.




3. Leave depressions flush with surface plane.

3.10 LEVELS OF FINISH

A. Conform to NWCB 300-301, GA-214, ASTM C 840, and provisions of Contract Documents.

B. Level 0 Finish: Accepted at walls not required to be fire-resistive construction at unfinished spaces. Apply to temporary construction. 1. No taping, finishing, or accessories required.

C. Level 1 Finish: Apply to fire-resistive wall construction in unfinished spaces as shown on Drawings. 1. Fire tape by embedding tape in joint compound at joints and angles. 2. Tool and ridge marks are accepted.

D. Level 2 Finish: Not used.

E. Level 3 Finish: Apply to mechanical and electrical utility areas not scheduled for paint finish. Apply to walls where heavy-weight wall coverings will be installed. 1. Fire tape by embedding tape in joint compound at joints and angles. 2. Apply two separate applications over taped joints and fastener heads. 3. Apply one coat over accessories. 4. Surfaces free of excess compound. 5. Tool and ridge marks not accepted.

F. Level 4 Finish: Apply to small rooms receiving paint finish and not subject to critical light reflection. Include maintenance and loading areas, restrooms, utility areas, mechanical, electrical, and custodial rooms. Apply to walls where light-weight wall coverings will be installed. 1. Sand between coats and after final coat, do not scuff paper, repair blemishes and

joint ridges. 2. After final sanding, wipe drywall surfaces with a damp sponge to remove dust and

particles. 3. Finish uniformly smooth, ready for paint finish or as substrate for other finishes. No

wall texturing is to be applied.

G. Level 5 Finish: Apply to public areas and large rooms receiving paint finish and not scheduled for veneer plaster. Include offices, corridors, lobbies, and kitchen production rooms, except where wall finish is covered with stainless steel panels where Level 4 Finish is acceptable. Over surface of Level 4 Finish: 1. Trowel apply thin skim coat of joint compound, USG Tuff-Hide Primer-Surfacer, or

other material labeled by manufacture for purpose of achieving Level 5 Finish. 2. Sand between coats and as needed for smooth finish. 3. Do not scuff paper. 4. Repair blemishes and joint ridges. 5. After final sanding, wipe surfaces with damp sponge removing dust and particles. 6. Leave areas finished uniformly smooth, free of tool marks and ridges, ready for work

of Section 099000.

3.11 TOLERANCES




A. Shim panels as necessary to conform to tolerances.

B. Between Board Faces: 1/16 inch offset.

C. Plane, Level, Warp, and Bow: 1/8 inch in 8 foot.

3.12 ADJUSTING

A. Remove and replace following gypsum board installations: 1. Board in contact with water for over 18 hour time period. 2. Gypsum core exhibiting dampness or water intrusion. 3. Facing paper exhibiting delamination. 4. Facing or core exhibiting mold growth or turning black. 5. Board sagging or warped. 6. Board directly exposed to water determined to be contaminated.

3.13 CLEANING

A. Clean beads, screeds, metal base, metal trim, mechanical and electrical items, and other work.

B. Wipe clean, leaving work ready for finish specified under other Sections.

C. As work is completed in each space, clean all rubbish, utensils, and surplus materials from the space. Leave floors broom-clean.

END OF SECTION


SECTION 093000TILE


SECTION 093000 TILE

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Tile interior wall and floor installations. 2. Metal trim shapes. 3. Porcelain Stone tile 4. Mortar, grout, joint sealants, and other accessories.

B. Related Sections: 1. Section 033000 - Cast-in-Place Concrete 2. Section 061000 - Rough Carpentry 3. Section 092216 - Non-Structural Metal Framing 4. Section 092800 - Backer Boards and Underlayment 5. Division 22 - Plumbing

1.2 REFERENCES


B. American National Standards Institute (ANSI): 1. ANSI A108.01 - General Requirements: Subsurfaces and Preparations by

Other Trades. 2. ANSI A108.1A - Installation of Ceramic Tile in the Wet-Set Method, with

Portland Cement Mortar. 3. ANSI A108.1B - Installation of Ceramic Tile on a Cured Portland Cement

Mortar Setting bed with Dry-Set or Latex-Portland Cement Mortar.

4. ANSI A108.1C - Contractors Option: ANSI A108.1A or ANSI 108.1B 5. ANSI A108.2 - General Requirements: Materials, Environmental and

Workmanship. 6. ANSI A108.4 - Installation of Ceramic Tile with Organic Adhesives or

Water Cleanable Tile-Setting Epoxy Adhesive. 7. ANSI A108.5 - Installation of Ceramic Tile Installed with Dry-Set Portland

Cement Mortar or Latex-Portland Cement Mortar. 8. ANSI A108.6 - Installation of Ceramic Tile with Chemical Resistant, Water

Cleanable Tile-Setting and -Grouting Epoxy. 9. ANSI A108.9 - Installation of Ceramic Tile with Modified Epoxy Emulsion

Mortar/Grout. 10. ANSI A108.10 - Installation of Grout in Tilework. 11. ANSI A108.13 - Installation of Load Bearing, Bonded, Waterproof

Membranes for Thin-Set Ceramic Tile and Dimension Stone.

12. ANSI A108.14 - Installation of Paper-Faced Glass Mosaic Tile. 13. ANSI A108.15 - Alternate Method: Installation of Paper-Faced Glass

Mosaic Tile. 14. ANSI A108.16 - Installation of Paper-Faced, Back-Mounted, Edge-

Mounted, or Clear film Face-Mounted Glass Mosaic Tile.


SECTION 093000TILE


15. ANSI A108.17 - Installation of Crack Isolation Membranes. 16. ANSI A118.1 - American National Specifications for Dry-Set Portland

Cement Mortar. 17. ANSI A118.3 - American National Specifications for Chemical Resistant,

Water-Cleanable, Tile-Setting and -Grouting Epoxy and Water Cleanable Tile-Setting Epoxy Adhesive.

18. ANSI A118.4 - American National Specifications for Latex-Portland Cement Mortar.

19. ANSI A118.6 - American National Specifications for Standard Cement Grouts for Tile Installation.

20. ANSI A118.7 - American National Specifications for Polymer Modified Tile Grouts for Tile Installation.

21. ANSI A118.8 - American National Specifications for Modified Epoxy Emulsion Mortar/Grout.

22. ANSI A118.10 - American National Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installation.

23. ANSI A118.12 - American National Specifications for Crack Isolation Membranes for Thin-Set Ceramic Tile and Dimensional Stone Installation.

24. ANSI A137.1 - Ceramic Tile.

C. American Society for Testing and Materials (ASTM) 1. ASTM C373 - Standard Test Method for Water Absorption, Bulk Density,

Apparent Porosity, and Apparent Specific Gravity of Fired Whiteware Products

2. ASTM C627 - Standard Test Method for Evaluating Ceramic Floor Tile Installation Systems Using the Robinson-Type Floor Tester

3. ASTM C648 - Standard Test Method for Breaking Strength of Ceramic Tile

4. ASTM C650 - Standard Test Method for Resistance of Ceramic Tile to Chemical Substances

5. ASTM C920 - Specification for Elastomeric Joint Sealants. 6. ASTM C1028 - Standard Test Method for Determining the Static

Coefficient of Friction of Ceramic Tile and Other Like Surfaces by the Horizontal Dynamometer Pull-Meter Method

7. ASTM D2244 - Standard Test Method for Rubber Property—Durometer Hardness

8. ASTM D4397 - Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications

D. Tile Council of North America (TCNA): 1. TCNA - Handbook for Ceramic Tile Installation. 2. TNCA A137.1 - Tile grade in accordance with: Recommended Standard

Specifications for Ceramic Tile.

1.3 SUBMITTALS


B. Product Data:


SECTION 093000TILE


1. Manufacturer's published literature for each product specified. 2. Sample warranty.

C. Shop Drawings: Show locations of each type of tile pattern. Show widths, details, and locations of expansion, contraction, control, and isolation joints in substrates and finished tile surfaces. Show stone thresholds where indicated.

D. Samples 1. Tile Samples: Full size in specified color. 2. Grout Samples: Cured colors and textures. 3. Control and Transition Trim Samples: Products, materials, and colors. 4. Sealant Samples: Cured colors and textures.

E. Certification: Written statement signed by installer’s representative and Contractor that grout, setting materials, and other accessories have been provided as specified, or where different, are as accepted by Architect.

F. Sample Warranty: Meet or exceed provisions specified by this Section.

1.4 MAINTENANCE DATA


B. Manufacturer's standard cleaning instructions and maintenance guide.

1.5 QUANTITY ASSURANCE

A. Provide grout and setting products from same manufacturer.

1.6 PERFORMANCE REQUIREMENTS

A. Static Coefficient of Friction: Provide flooring materials with the following values as determined by testing according to ASTM C1028: 1. Level Surfaces: Minimum 0.6. 2. Ramp Surfaces: Minimum 0.8.

1.7 QUALIFICATIONS

A. Installer: Company and employees specializing in work of this section with minimum 5 years documented experience.


A. Conform to provisions of Section 014100.

B. Accessibility Requirements: State of Washington, WAC 51-50-1000, Chapter 10 Means of Egress and WAC 51-50-1100, Chapter 11 Accessibility.

1.9 MOCK-UPS

A. Provide under provisions of Section 014300.


SECTION 093000TILE


B. Construct mock-up at adjacent wall and floor area, approximately 4 feet wide by 4 feet vertical by 4 feet horizontal. Include inside and outside corners and decorative tile.

C. Build-in specified components of construction.

D. Locate as instructed by Architect at adjacent wall and floor area.

E. Illustrate alignment of wall and floor patterns.

F. Build-in specified components of construction including colored sealant at wall base.

G. Architect accepted mock-up may remain as part of Work of this Contract.

H. Protect accepted mock-up as standard of quality for work of this Section.


A. Arrange, in accordance with Section 013119.

B. Attendance: Contractor, installer, Owner, Architect, manufacturer’s representative, and those requested to attend.

C. Meeting Time: Minimum 2 weeks prior to prior to beginning work of this Section and work of related Sections affecting work of this Section.

D. Location: Project Site.

E. Agenda: Include placement and types of expansion joints and trim, waterproof membrane, and grouting of joints.


A. Conform to provisions of Section 016600 and manufacturer's instructions to protect from damage.

B. Deliver in manufacturer's unopened, labeled packaging.


A. Do not install adhesives in unventilated areas.

B. Maintain minimum 50 degree F ambient temperature during installation and for 7 days following installation and as required by manufacturer's instructions.

1.13 COORDINATION


B. Section 033000 for sloping of concrete slab to floor drains or concrete slab depression for tile setting beds.

C. Division 22 for plumbing penetrations and installations.


SECTION 093000TILE


1.14 WARRANTY

A. Systems Warranty: Manufacturer’s 5 year Systems Warranty for mortars and grouts.

PART 2 PRODUCTS

2.1 TILE MANUFACTURERS

A. Crossville, distributed by United Tile. 1. Tel (425)-251-5290, Fax (425) 251-5047, Email [email protected] (Lisa

Anderson). 2. Website: http://www.crossvilleinc.com

B. Cube, distributed by Statements Distincitve Tile and Stone 1. Tel (206) 250-2415, Email [email protected] (Jill Reid) 2. Website: http://www.statementstile.com


2.2 TILE MATERIALS

A. Ceramic Tile: Meet or exceed ANSI 137.1.

B. Porcelain Stone Floor Tile: (PST): 1. Manufacturer: Crossville 2. Product: Ecocycle 3. Color: EC001 Storm, Cross Sheen 4. Size: 8 by 8 by 5/16 inch

C. Porcelain Cove Base Tile: 1. Manufacturer: Crossville 2. Product: Ecocycle 3. Color: EC001 Storm, Cross Sheen 4. Size: 6 by 8 by 5/16 inch

D. Ceramic Wall Tile: (CT): 1. Manufacturer: Cube 2. Product: Bianco Matte 3. Color: White 4. Size: 2 by 4 by 1/4 inch on 12 x 12 mesh.

2.3 SETTING MATERIALS, GROUTS, WATERPROOFING, SEALERS, AND ACCESSORIES MANUFACTUERS:

A. Durabond / Hydroment (Bostik Findley) 1. Tel (503) 466-9405, Email [email protected] (Scott Portman Territory Sales

Mgr), 2. Website http://www.bostik.com

B. Custom Building Products 1. Tel (800) 246-5177 / (206) 762-6620, Direct Line (206) 767-2265, Fax (206) 768-

2816, Pager (800) 730-1145, Email [email protected] (Chuck Hill, Mfrs Rep).


SECTION 093000TILE


2. Cell (209) 518-1153, Fax (209) 477-6752, Email [email protected] (John Gallup, Regional Tech Sales Rep).

3. Cell (206) 250-4675, Fax (425) 254-9262, Email [email protected] (Bob McCall, CTC, NW Territory Mgr),

4. Website http://www.custombuildingproducts.com

C. LATICRETE International, Inc. 1. Tel (800) 243-4788 X 235 / (203) 393-0010, Fax (203) 393-1948, Cell (203) 464-

5341, Email [email protected] (Mike Werner, CCTS) 2. Website http://www.laticrete.com

D. MAPEI, Corporation. 1. Cell (360) 921-9518, Email [email protected] (Mike Piazza). 2. Website http://www.mapei.com

E. TEC, Specialty Construction Brands (Subsidiary of H.B. Fuller Company). 1. Website http://www.tecspecialty.com

F. Substitution Requests: Submit for approval under provisions of Section 012500.

2.4 MORTAR

A. Conform to TCNA for Heavy Performance Level.

B. Thin-Set Bond Coat: Two-part mortar conforming to ANSI A118.4 with high-polymer, liquid acrylic Latex additive used in place of water. 1. Bostik Tile-Mate 760 with Hydroment 447 Flex-A-Lastic Mortar Admixture 2. Custom Versabond Flex Fortified Thin-Set Mortar 3. LATICRETE

a. LATICRETE 211 Crete Filler Powder with LATICRETE 4237 Latex Thin-Set Mortar Additive.

b. LATICRETE 317 Thin-Set Mortar with LATICRETE 333 Super Flexible Mortar Admixture.

4. MAPEI KERABOND Dry Set Mortar with MAPEI 300 KERALASTIC Liquid Polymer Additive.

C. Portland Cement Mortar (Thick Set) at Floors: ANSI A108.2, thickness 1-3/8 inch minimum to 4-inch thick, as required to slope to floor drains and to align with other subflooring systems. 1. Portland Cement Mortar: Conform to ANSI A108.1A 2. Mortar Admixture:

a. Bostik Multi-Purpose Acrylic Latex Mortar Admixture with Hydroment 425, Grout Additive

b. Custom– CustomFloat with ThinSet Mortar Additive c. LATICRETE 3701 Fortified Mortar Bed d. MAPEI PRP 309 PLANICRETE 50 Multi-Purpose Latex Additive

D. Organic Adhesives / Mastic (ANSI A136.1): Not accepted for any conditions.

2.5 GROUT

A. Sanded Grout - Tile Joints 1/8 inch or Wider - Walls: Polymer modified, colored grout,


SECTION 093000TILE


conforming to ANSI 118.7 with 2 part epoxy emulsion conforming to ANSI A118.8. 1. Bostik Ceramic Tile Grout Joint Filler with Hydroment 425 Acrylic Latex Multi-

Purpose Mortar Admixture and Grout Additive used in place of mixing water, conforming to ANSI 118.4

2. Custom Polyblend Sanded Tile Grout, polymer modified 3. LATICRETE PermaColor Grout 4. MAPEI Ultracolor Ultra/Color

B. Epoxy Grout – Floors: Colored, two-component epoxy resin, mold, chemical, stain, and shock resistant compound conforming to ANSI A118.3. Suitable for horizontal tile joints 1/16 inch to 1 inch wide, and vertical tile joints 1/16 inch to 3/8 inch wide. 1. Bostik Color-Poxy, 100 percent Solids, Colored Epoxy Setting and Grouting System. 2. Custom:

a. CEG-2000 100% Solids Commercial Epoxy Grout b. 100% Solids Epoxy Grout (water cleanup)

3. LATICRETE a. SpectraLOCK PRO Grout for restroom areas

4. MAPEI Inc., KERAPOXY, Epoxy Grout

2.6 MEMBRANES

A. Uncoupling/Waterproofing/Drainage Membrane System: Membrane, Metal Divider Trim, and Control/Transition Edge Trim Systems: 1. Schlüter Systems

a. Cell (206) 412-5203, Fax (877) 685-0583, Email [email protected] (Kevin Vaughn).

b. Tel (800) 472-4588 (Home Office). c. Website http://www.schluter.com

2. Substitution Requests: Submit for approval under provisions of Section 012500.

B. Membrane: Schluter-DITRA, polyethylene membrane, vacuum formed into 1/8 inch thick grid of square dovetail cavities, laminated to anchoring fleece on bottom side.

C. Accessories: Include Schluter-KERDI-BAND (waterproofing tape), Schluter-KERDI-FLEX (flexible waterproofing tape), and Schluter-KERDI-KERECK (preformed corners), Schluter-KERDI-KM (pipe collar), and as instructed by manufacturer to make complete uncoupling/waterproof drainage system.

D. Waterproof and Anti-Fracture Membrane: Conform to ANSI A118.10. 1. LATICRETE 9235 Waterproofing Membrane or LATICRETE Hydro Ban

E. Liquid Trowel Applied Waterproof Membrane and Anti-Fracture Membrane: Conform to ANSI A118.10 an A118.12. VOC content of 65 g/L or less when calculated according to 40 CFR 59, Subpart D (EPA Method 24). 1. Bostik Ultra-Set 2. Custom RedGuard Waterproofing and Crack Prevention Membrane 3. LATICRETE 9235 Waterproofing Membrane or LATICRETE Hydro Ban 4. MAPEI Mapelastic PRP 315 5. TEC Hydraflex – Waterproofing Crack Isolation Membrane

2.7 EXPANSION AND ISOLATION JOINTS


SECTION 093000TILE


A. Interior Expansion Joints, Joint Sealant, and Backer Material: 1. Conform to TCNA, EJ171. Match colors and textures of grout (sanded and

unsanded). 2. Joint Sealants: Silicone sealant and backer as specified Section 079200. 3. Hydroment, CHEM-CALK 900, one-part urethane sealant for tile and marble, ASTM

C920, Class 25, non-sag, ASTM D2244 Durometer Hardness 35, specified for type and quality.

4. Vertical Joints: ASTM C920, Grade NS, Class 25, Use NT, M, & G, mildew-resistant silicone or polyurethane or mildew-resistant silicone, single or multi-component.

5. Horizontal Joints: ASTM C920, Grade P, Class 25, Use T, M, & G, ASTM D2240 Durometer Hardness 35 or greater, polyurethane or mildew-resistant silicone, single or multi-component.

2.8 TRIM

A. Metal Divider and Edge Trim: Schlüter Systems, solid metal edge protection trim in lengths, sizes, and types to align top edge with tile floor surface and conforming to ADA requirements. 1. Edge Transition:

a. Schlüter-SCHIENE-ATB 2. Vertical Edge Protection Trim:

a. Schluter – Jolly – ACGB, Brushed Chrome Anodized Aluminum

B. Level Transitions, Expansion Joints, and Control Joints: 1. Inside Corner Wall to Wall and Wall to Floor Transition Control Joints: Schlüter-

DILEX-AHK, ACGB. 2. Over Expansion Joints: Schlüter Dilex-BWS

2.9 SEALERS

A. Tile Penetrating Sealer: Two coat application: 1. Aqua Mix Inc., Sealer’s Choice Gold, water-based penetrating sealer (47 g/l) 2. Custom Building Products, TileLab Grout & Tile Sealer (33 g/l) 3. TEC Guard All – Invisible Penetrating Sealer.

B. Other Materials: Conform to TCNA Standard Specifications.

2.10 FINISHES

A. Tile: As specified in this Section.

B. Wall Grout Color: As accepted by Architect.

C. Floor Grout Color: As accepted by Architect.

D. Metal Divider and Edge Trim: Brushed Chrome Anodized Aluminum.

E. Level Transitions, Expansion Joints, and Control Joints: Brass

PART 3 EXECUTION

3.1 EXAMINATION


SECTION 093000TILE


A. Verify installation conditions as satisfactory to receive work of this Section.

B. Verify that concrete floor slabs are sloped to drains and are suitable for installing tile.

3.2 PREPARATION

A. Lay out work and center tile pattern to reduce cutting and to prevent small pieces less than 1/2 full size.

B. Where expansion joints and other breaks in mid-field occur, begin tile layout with whole tile size at both sides of break.

C. Protect surrounding surfaces to preclude damage from work of this Section.

3.3 INSTALLATION - GENERAL

A. Conform to TCNA Methods, manufacturer's instructions, ANSI Standards, and provisions of Contract Documents. 1. Ceramic Tile: Conform to ANSI A108.5. 2. Grout Joints:

a. Walls: Conform to ANSI A108.10. b. Floors: Conform to ANSI A108.6.

B. Evenly mix color and shade variations. Mix tile from different containers.

C. Grind edges and install to prevent visible cut edges.

D. Cut neatly around bases, trim, fixtures, and similar conditions.

E. Align tile joints at walls and floor.

F. Install specified ceramic base and trim shapes.

G. Pointing and Grouting: 1. Tool joints full and flush without voids or pinholes. 2. Clean excess grout from tile surface as work progresses. 3. Recess grout evenly at bottom of cushion edges and radius edges of tile.

H. Damp cure tile installations for 3 days in accordance with TCNA and ANSI standards.

I. Unspecified Installation Conditions: Conform to TCNA Methods and verify with Architect.

3.4 INTERIOR TILE WALL INSTALLATION

A. Install tile over tile backerboard specified Section 092800.

B. Do not install tile Installations over paper faced tile gypsum board, including moisture-resistant board (green board).

C. Apply leveling skim coat over tile backerboard, as necessary to provide smooth flat surface free of out of plane depressions and irregularities exceeding 1/8 inch in 10 foot.


SECTION 093000TILE


D. Install tile over prepared tile backerboard using thinset latex Portland cement bond coat.

E. Install sanded grout as specified in Part 2 and in accordance with manufacturer’s instructions.

3.5 INTERIOR TILE FLOOR INSTALLATION

A. Thin-Set Tile over Uncoupling/Waterproofing/Drainage Membrane: Conform to manufacturer’s instructions as required to complete system installation. 1. Apply thin-set mortar bond coat over concrete substrate using notched trowel. 2. Solidly embed anchoring fleece side of polyethylene uncoupling membrane into

mortar bed. Work membrane into mortar bed using float or screed trowel. 3. Seam joints with manufacturer’s waterproofing strip to form continuous waterproof

membrane.

B. Metal Trims: Install at metal dividers, vertical edges, expansion joints, control joints, and changes in finish floor materials. Align top edge of trim with surface of tile.

C. Extend tile into recesses and under equipment and fixtures to form a complete covering without interruptions.

D. Slope tile to drain where indicated on Drawings.

E. Floor Tile Penetrating Sealer: Apply 2 coats in accordance with manufacturer's instructions.

F. Install epoxy grout in accordance with manufacturer’s instructions.

3.6 EXPANSION JOINTS AND JOINT SEALANTS

A. Conform to TCNA EJ171 for expansion joint, isolation joint, perimeter joint construction joint, contraction joint, and generic movement joint systems, and provisions of Contract Documents.

B. Install joint sealant and backer rod or bond breaker tape conforming to TCNA EJ171 guidelines.

C. Install continuous control joint around floor perimeters between tile at floor and wall and where tilework abuts other restraining surfaces as necessary to allow independent differential expansion and contraction between floor and wall planes.

D. Install continuous control joint at inside corners of tile faced abutting walls to allow independent differential movement between wall planes.

E. Install sealant at joints at built-in plumbing fixture perimeters of meeting tile.

F. Seal around pipes and other penetrations through tile.

G. Provide expansion/control joints where indicated on Drawings, and as follows: 1. Interior: 20 feet to 25 feet in each direction. 2. Exterior: 8 feet to 12 feet in each direction. 3. Interior tilework exposed to direct sunlight or moisture: 8 feet to 12 feet in each


SECTION 093000TILE


direction.

3.7 ADJUSTING

A. Remove and replace damaged tile, such as broken, chipped, and stained units.

B. Remove work where joints are out of alignment or spaced unevenly.

C. Repair or replace work not conforming to mock-up or other specified requirements.

3.8 CLEANING

A. Clean work not less than 6 days after completion of work, using clean water and stiff bristle brushes.

B. Do not wire brush, use acid-type cleaning agents, or use other cleaning compounds with caustic or harsh fillers.

END OF SECTION


SECTION 095113ACOUSTICAL PANEL CEILINGS (ACP)


SECTION 095113 ACOUSTICAL PANEL CEILINGS (ACP)

PART 1 GENERAL

1.1 SUMMARY:

A. Section Includes: 1. Suspended sound-absorbing mineral fiber and glass fiber acoustical ceiling panels. 2. Suspended sound-diffusing ceiling panels.

B. Related Sections: 1. Section 092900 - Gypsum Board 2. Section 095300 - Acoustical Ceiling Suspension Assemblies 3. Division 21 - Fire Suppression 4. Division 22 - Plumbing 5. Division 23 - Heating, Ventilating, and Air Conditioning 6. Division 26 - Electrical

1.2 REFERENCES


B. American Society for Testing and Materials (ASTM) International: 1. ASTM C423 - Test Method for Sound Absorption and Sound Absorption

Coefficients by the Reverberation Room Method. 2. ASTM E413 - Classification for Rating Sound Insulation. 3. ASTM E1264 - Classification for Acoustical Ceiling Products 4. ASTM E1414 - Test Method for Airborne Sound Attenuation Between Rooms

Sharing a Common Ceiling and Plenum.

C. Ceiling and Interior Systems Contractors Association (CISCA): Acoustical Ceiling/Use and Practice.

1.3 SUBMITTALS

A. Submit in accordance with the requirements of Section 013300.

B. Product Data: Manufacturer's technical data for each product.

C. Shop Drawings: Reflected ceiling plans. 1. Indicate grid layouts, dimensions, and profiles, and items to be installed on or with

ceiling. 2. Include junctions and interactions with other finishes, systems, and mechanical and

electrical items. 3. Show conformance with Code requirements. 4. Coordinate with coordination shop drawings specified in Section 013113.

D. Samples: Submit 6 inch by 6 inch samples of each panel type illustrating color and range of appearance.




E. Manufacturer's Instructions: Include installation requirements, special procedures, and conditions requiring special attention.


A. Installer Qualifications: Company specializing in work of this Section with minimum 5 years documented experience installing commercial quality work of comparable scope.

B. Single Source Responsibility: Sections 095300 and 095113. 1. Perform work by or under direct supervision of same installer. 2. Provide tee bar ceiling grid and mineral fiber sound-absorbing acoustical ceiling panels

by same manufacturer.


A. Regulatory Requirements: Comply with provisions of Section 014100.

B. Surface Burning Characteristics: UL Labeled Class A Rated, Flamespread 0-25, tested to ASTM E1264.



B. Deliver materials in original, unopened, protective packaging with manufacturer's labels indicating brand name, pattern, size, and thickness attached and legible.

C. Store cartons and bundles at required temperature and humidity.

D. Do not begin installation until sufficient materials are received to complete the space.


A. Do not begin installation until gypsum board, painting, and other wet work is dry.

B. Install under standard occupancy conditions, between 60 degrees F and 85 degrees F, not more than 80 percent relative humidity, building fully enclosed.

1.8 COORDINATION


B. Coordinate with Section 095300 for installation with suspension system.

C. Division 21 for sprinkler system heads located at acoustical ceilings.

D. Division 23 for mechanical penetrations and locations, including grilles and diffusers.

E. Division 26 for electrical penetrations and locations including lighting fixtures, fire detection equipment, and exit signs




1.9 WARRANTY

A. Conform to Warranty provisions specified Section 017836.

B. Mineral Fiber Acoustical Ceiling Panels: Manufacturer standard 15 year Warranty against sag, warping, and mold.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Armstrong World Industries. 1. Cell (206) 919-0438, Fax (253) 862-4775, Email [email protected] (Tim

Hamilton CSI). 2. Website http://www.armstrong.com/

B. USG Interiors, Inc. 1. Cell (425) 468-9355, Fax (425) 888-5355, Email [email protected] (Scott Finlinson). 2. Website http://www.usg.com.

C. Hunter Douglas Architectural Products; 1. Cell (206) 719-6443, Fax (425) 487-9633, Email [email protected] (Rob Maddox,

Mfrs Rep) 2. Cell (206) 719-6441, Email [email protected] (Wade Nash, Spec Systems) 3. Tel: 866-556-1235; Fax: 720-872-7850; 4. Website: www.hdtechstyle.com.

D. Substitution Requests: Submit for approval under provisions of Section 012500.

2.2 ACOUSTICAL PANELS (ACP-1)

A. Acoustical Ceiling Panel (ACP-1): 1. Product: Hunter Douglas Techstyle 2. Provide panels comprising composite structural fiberglass core with non-woven

polyester textile surface wrapped on two opposite edges and matching integral hinged support clip on other two edges; with properties as follows: a. Panel Thickness: 1.125 inches. b. Panel Size: As shown on Drawings. c. Reveal: Panels configured to maintain reveal of 1/4 in between adjacent panels. d. Panel Color: White e. Noise Reduction Coefficient (NRC): 0.85, measured in accordance with ASTM C 423

with the equal to or better than absorption coefficient reading at the following specified frequencies: Frequency: 125 250 500 1000 2000 5000

Absorp Co-ef 0.61 0.82 0.65 0.88 1.04 1.03

f. Surface Burning Characteristics: Flame spread less than 25 and smoke developed less than 50, Class A (1), per ASTM E 84 and ASTM E 1264.

g. Light Reflectance (white only): LR-1 (75%), measured in accordance with ASTM E 1477.




h. Moisture Resistance: Resistant to relative humidity up to 95 percent at 105 degrees F (40.5 degrees C) for 30 days.

i. Mold and Mildew Resistant: In accordance with requirements of ASTM C 665. j. Fungi Resistant: Inc accordance with requirements of ASTM C 1338.

2.3 SQUARE-EDGE MINERAL FIBER ACOUSTICAL CEILING PANELS

A. Acoustical Ceiling Panel (ACP-2): 1. Products:

a. Armstrong, Ultima, Fine Textured. b. USG Interiors, ClimaPlus 2410.

2. Edge Style: Square Edge, Tegular 3. Size: 24 by 48 by 3/4 Inch. 4. Grid: 9/16 inch. 5. Basic Compliance Standard: ASTM E1264, Type IV, Form 2, Pattern E, Fire Class A. 6. Acoustical Performance:

a. Noise Reflectance Coefficient (NRC) Range: 0.70, tested to ASTM C423. b. Ceiling Attenuation Class (CAC): 35, tested to ASTM E1414.

7. Light Reflectance: 0.89 minumum.

2.4 SQUARE-EDGE MINERAL FIBER ACOUSTICAL CEILING PANELS

A. Acoustical Ceiling Panel (ACP-3): 1. Products:

a. Armstrong, Health Zone Ultima b. USG Interiors, Mars Healthcare

2. Edge Style: Square Edge, Tegular 3. Size: 24 by 48 by ¾ Inch 4. For Grid Size: 9/16 inch 5. Basic Compliance Standard: ASTM E1264, Type IV, Form 2, Pattern E, Fire Class A 6. Acoustical Performance:

a. Noise Reflectance Coefficient (NRC) Range: 0.70 minimum b. Ceiling Attenuation Class (CAC): 35

7. Light Reflectance: 0.86 minumum

2.5 ACCESSORIES

A. Suspension System: As specified in Section 095300.

B. Panel Retention Clips: Impact-resistant acoustical ceiling panel installations. : 1. Armstrong, 414. 2. USG Interiors, 20428.

C. As necessary to complete installation in accordance with manufacturer’s instructions.

2.6 FINISHES

A. Exposed Panel Surface Color: 1. Typical: Manufacturer’s standard white, unless otherwise indicated.




PART 3 EXECUTION

3.1 EXAMINATION


B. Verify fire sprinklers system, mechanical ductwork, and electrical lighting, wiring, fire detection, and other equipment ready for work of this Section.

C. Verify interfacements in place between acoustical suspension system and adjacent construction.

3.2 INSTALLATION OF LAY-IN ACOUSTIC PANELS

A. Conform to manufacturer's instructions, CISCA, and provisions of Contract Documents.

B. Install in suspended exposed tee grid systems specified Section 095300.

C. Install continuously at entire ceiling areas designated for acoustical ceiling panels, except for where mechanical, electrical, and other penetrations, finishes, or treatments are indicated.

D. Fit units in place in manner to be free from damaged edges, soiled surfaces, and other defects to appearance and function.

E. Fit border units neatly against abutting surfaces leaving no gaps, exposed or cut edges.

F. Install level, in uniform plane, free from twist warp, and dents.

G. Tegular Edges: Neatly field cut new tegular edges into panels that are cut to less than full size so that panels lay flat and level in grid suspension system. Buttons and other shimmed panel methods not accepted.

3.3 ADJUSTING

A. Remove and replace damaged, soiled, and discolored materials and work not conforming to Contract Documents.

END OF SECTION


SECTION 095300ACOUSTICAL CEILING SUSPENSION ASSEMBLIES


SECTION 095300 ACOUSTICAL CEILING SUSPENSION ASSEMBLIES

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Suspended metal tee grid ceiling system and perimeter trim for lay-in acoustical ceiling

panels. 2. Suspended metal tee grid ceiling system and perimeter trim for tegular, square edge

acoustical ceiling panels. 3. Acoustical isolation hangers. 4. Provisions for mechanical and electrical penetrations and installations.

B. Related Sections: 1. Section 095113 - Acoustical Panel Ceilings 2. Division 21 - Fire Suppression Systems 3. Division 22 - Plumbing 4. Division 23 - Heating, Ventilating, and Air Conditioning 5. Division 26 - Electrical

1.2 REFERENCES


B. American Society of Civil Engineers (ASCE) and Structural Engineering Institute (SEI): 1. ASCE/SEI 7 - Minimum Design Loads for Buildings and Other Structures.

C. American Society for Testing and Materials (ASTM) International: 1. ASTM A153 - Specifications for Zinc-Coating (Hot-Dip) on Iron and Steel

Hardware. 2. ASTM A641 - Specifications for Zinc-Coated (Galvanized) Steel Wire. 3. ASTM C635 - Standard Specification for the Manufacturer, Performance,

and Testing of Metal Suspension Systems for Acoustical Tile and Lay-In Panel Ceilings.

4. ASTM C636 - Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels.

5. ASTM A653 - Standard Specification for Steel Sheet, Zinc Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvanized) by the Hot-Dip Process.

D. Ceiling and Interior Systems Contractors Association (CISCA): Conform to applicable publications. Website http://cisca.org/home 1. CISCA - Acoustical Ceilings Use & Practice. 2. CISCA - Ceiling Systems Handbook. 3. CISCA - Guidelines for Seismic Restraint for Direct-hung Suspended

Ceiling Assemblies - Seismic Zones 3 & 4.

E. Northwest Wall and Ceiling Bureau (NWCB), Tel (206) 524-4243 (Bob Drury/Terry Kastner). Website http://www.nwcb.org. 1. NWCB 400-101 - Ceiling Systems




2. NWCB 400-102 - Suspended Ceiling Systems 3. NWCB 400-401 - Suspension Systems for Acoustical Lay-In Ceilings

1.3 DESIGN REQUIREMENTS

A. System Design: Prefinished metal modular grid suspension system designed to secure acoustical ceiling panels and integral mechanical and electrical components. 1. Components: Lock together in a positive manner. 2. Install to conceal plenum space above acoustical ceiling system and to allow access. 3. Make provisions for vertical as well as horizontal suspension systems.

B. Non-Fire Rated Grid: ASTM C635 Heavy Duty Classification (double web steel) exposed Tee with die cut components.

C. Seismic Lateral Design for Seismic Categories D, E, & F: 1. Conform to IBC Section 1613 including ASCE/SEI 7 Section 9.6.2.6, for 2 inch closure

angle with one end of ceiling grid attached to angle and other end with 3/4 inch clearance of grid to wall and with freedom to slide on closure angle. Other designs, as accepted by Regulatory Authority having local jurisdiction.

2. Conform to IBC Section 803.9 and ASCE/SEI 7 Section 9.6.2.6.2.2, including requirement for independent support from structure above for light fixture and mechanical services installed into acoustical lay-in panel ceiling systems.

3. Conform to ASCE/SEI 7 Section 13.5.6.2.2.d for ceiling areas exceeding 2,500 square feet. Provide a seismic separation joints or structural analysis.

D. Minimum Design Components: Meet or exceed NWCB 400-401 and CISCA Guidelines for Zones 3 & 4 for Seismic Design Categories D, E, or F as defined by Structural Notes.

E. Main Runners and Cross Runners Pull out Tension: Minimum 180 pounds or twice the actual load whichever is greater, conforming to CISCA Guidelines for Seismic Zones 3 & 4.

1.4 SUBMITTALS


B. Product Data: Published performance data on metal grid suspension systems and components conforming to ASTM C635.

C. Shop Drawings: Reflected ceiling plans. 1. Indicate grid layouts, dimensions, and profiles, and items to be installed on or with

ceiling. 2. Include junctions and interactions with other finishes, systems, and mechanical and

electrical items. 3. Indicate seismic joints and seismic restraint systems. 4. Show conformance with Code requirements. 5. Coordinate with coordination shop drawings specified in Section 013113.

D. Samples: Full-size sample of grid system unit illustrating material and finish to match color of acoustical panels specified Section 095113. Include clips and accessories for each system.




E. Design Data: Submit calculations defining conformance with seismic bracing requirements of IBC. Design is required to bear stamp of Structural Engineer licensed in Washington State.

F. Manufacturer's Installation Instructions: Indicate special procedures, perimeter conditions requiring special attention and recommendations for suspension system installation.


A. Installer Qualifications: Company specializing in work of this Section with minimum 5 years documented experience installing commercial quality work of comparable scope.

B. Single Source Responsibility: Section 095300 and Section 095113. 1. Perform work by or under direct supervision of same installer. 2. Provide tee bar ceiling grid and acoustical ceiling panels by same manufacturer.


A. Conform to requirements of regulatory agencies specified by Section 014100.

B. Acoustical Ceiling Systems: Conform to IBC Section 803.9 and IBC Section 1621, including incorporated provisions of ASCE/SEI 7, 9.6.2.6 Suspended Ceilings.

1.7 MOCK-UP


B. Locate complete grid system at location as instructed by Architect.

C. Provide minimum 144 square foot mock-up as required to illustrate each system.

D. Include system components including as required to meet building code authority having jurisdiction.

E. Verify mock-up as conforming to manufacturer’s instructions and provisions of Contract Documents. Make adjustments as required for system conformance.

F. Do not begin work of this Section until inspection by manufacturer’ s representative and building code official is complete and system is accepted by Architect.

G. Protect and maintain accepted mock-up as standard of quality for work of this Section.

H. Incorporate accepted mock-up into work of this Section.



B. Deliver products in original, unopened, protective packaging.

C. Store products in original protective packaging in safe, protected location.




1.9 PROJECT CONDITIONS

A. Conform to CISCA handbook and Northwest Wall and Ceiling Bureau recommendations, including NWCB 400-401.

1.10 COORDINATION

A. Conform to Section 013113 for coordination with related Sections.

B. Section 095113 for acoustical ceiling panels installed into work of this Section.

C. Division 21 for sprinkler system heads located at acoustical ceilings.

D. Division 23 for mechanical penetrations and locations, including grilles and diffusers.

E. Division 26 for electrical penetrations and locations including lighting fixtures, fire detection equipment, and exit signs

1.11 WARRANTY


B. Ceiling Grid System: Manufacturer standard 10 year Warranty against corrosion, rust, and manufacturing defects.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Armstrong World Industries, 1. Cell (206) 919-0438, Voice Mail (877) 276-7876 Option 8 Ext 8143, Fax (253) 862-

4775, Email [email protected] (Tim Hamilton CSI). 2. Website http://www.armstrong.com

B. USG Interiors, Inc., 1. Cell (425) 468-9355, Fax (425) 888-5355, Voice Mail (800) 874-8880 Ext 6750, Email

[email protected] (Scott Finlinson, CSI). 2. Website http://www.usg.com

C. Chicago Metallic Co. 1. Tel (425) 277-0631, Fax (425) 277-5446, Email [email protected] (Schwarz &

Associates, Andy Schwarz / Cell (206) 218-3489, Email [email protected] Jerald Schwarz)

2. Website http://www.chicagometallic.com )

D. Substitution Requests: Submit under provisions of Section 012500.

2.2 PRODUCTS

A. Nonrated Suspension System – 15/16 inches wide 1. Armstrong, Prelude XL 15/16” Exposed Tee 2. USG, Nonrated: DX/DXL, Heavy Duty




3. CMC, 1200 System

2.3 SUSPENDED TEE BAR GRID SYSTEM

A. Grid Materials: ASTM A653 G30 minimum, commercial quality cold-rolled electro-galvanized steel.

B. Grid Suspension System for Lay-in Acoustical Panels 1. Main-Tees: 15/16 inch exposed flange with rolled cap, minimum 1-1/2 inch deep. 2. Cross-Tees: 15/16 inch exposed flange with rolled cap, minimum 1-1/2 inch deep.

a. Extended Web: Forming positive interlock. b. Lower Flange: Extended and offset. c. Mitre intersection with 1/8 inch reveal

C. Grid Suspension System for Square Edge, Tegular Acoustical Ceiling Panels 1. Product: Armstrong Suprafine XL 9/16”

a. Main-Tees: 9/16 inch exposed flange b. Cross-Tees: 9/16 inch exposed flange

2.4 WALL MOLDINGS

A. Angle Moldings for 15/16 inch Grid: Nominal 1 inch vertical and 2 inch horizontal legs. 1. Armstrong: 7812 2. USG: M20 Seismic Wall Mold

B. Shadow Molding for 15/16 inch Grid: 3/4 inch reveal with 2 inch horizontal leg. 1. Armstrong 7823 2. USG MS-274 – Seismic Shadow Molding

C. Shadow Molding for 9/16 inch Grid: 3/8 inch reveal with 9/16 inch horizontal leg. 1. Armstrong 7873 2. USG MS174

D. Angle Moldings Clips for 15/16 Grid: 1. Armstrong: BERC2 with 7/8 inch molding 2. USG: AC-M7 CLIP with molding

E. Angle Moldings for 15/16 inch Grid: Nominal 1 inch horizontal and vertical legs. 1. Armstrong: 7800 2. USG: MC11A

2.5 ACCESSORIES

A. Hanger Wire: Conform to NWCB 400-401, CISCA, and ASTM C 636. 1. 12 gauge supported at 4 foot centers. Other spacing as supported by stamped

structural calculations. 2. Galvanized soft-annealed, mild steel. 3. Pre-stretched, yield stress load of at least 3 times design load.

B. Lateral Seismic Force Bracing: Conform to NWCB 400-401and CISCA Guidelines for Seismic Restraint for Direct-hung Suspended Ceiling Assemblies (Zone 3-4), in Seismic Category D, E, and F.




C. Perimeter Trim: Extruded aluminum profiles, factory applied color coating same as grid system, nominal height as indicated on Drawings by 3/4 inch deep channel. 1. Armstrong Axiom Classic Trim 2. USG Compasso

D. Other Accessories and components: Manufacturer's tee-clips, bracing angles, and as required to complete and reinforce system.

E. Perimeter Trim at Clouds and Other Floating Edges: Extruded aluminum profiles, factory applied color coating same as grid system, nominal height as indicated on Drawings by 3/4 inch deep channel. 1. Armstrong Axiom Classic Trim 2. USG Compasso

2.6 FINISHES

A. Exposed Tee Bar Grid Finish: Low-gloss factory-applied paint finish.

B. Color: Match color of acoustical panels specified Section 095113.

PART 3 EXECUTION

3.1 EXAMINATION


B. Field measure to verify actual conditions, and verify that layout of grid system does not interfere with other work.

C. Verify that mechanical and electrical work in plenum space above ceiling is complete and that locations of equipment and light fixtures are located and installed.

3.2 INSTALLATION

A. Install in accordance with manufacturer's instructions, ASTM C635, and ASTM C636, NWCB 400-401, CISCA Zone 3 & 4, and provisions of Contract Documents.

B. Install system capable of supporting imposed loads with L/360 maximum span deflection.

C. Suspend mechanical equipment and electrical fixtures independently from suspended ceiling system to conform to ASCE/SEI 7, 9.6.2.6, ASTM C636, and ASTM C636.

D. Lay out system to a balanced grid design with edge units no less than 50 percent of acoustical panel size, except as otherwise indicated by reflected ceiling plan.

E. Install after major above ceiling work is complete. Coordinate location of hangers with other work.

F. Space hanger wires on main tees conforming to NWCB 400-401 and CISCA Zone 3 & 4 and ASTM C636 and as indicated on Drawings.




G. Hang suspension system independent from walls, columns, ducts, pipes, and conduit. Where hanging members are spliced, avoid visible displacement.

H. Where ducts or other components prevent regular spacing of hangers, provide trapeze to span extra distance as indicated on Drawings. 1. Do not interfere with mechanical or electrical work. 2. Do not support from ductwork or piping.

I. Do not support components on main tees or cross tees where weight may cause dead loads to exceed deflection tolerances of system.

J. Support light fixture loads by supplementary hangers located within 6 inches of each corner or support components.

K. Do not eccentrically load system or cause forces resulting in rotation of tees.

L. Install hangers at maximum 8 inch from vertical surfaces. Do not splay more than 1 in 6 out of plumb in vertical drop.

M. Install stabilizer bar or other suitable system to keep perimeter main tees and cross tees from spreading apart.

N. Provide hangers, channels, connectors, clips, and as required for installation of ceiling related accessories.

O. Reinforce vertical support systems with metal angles pop riveted into horizontal and vertical main-tees at 24 inches on center, and as required for rigid system.

P. Form expansion joints to accommodate plus or minus 1 inch movement. Maintain visual closure.

Q. Install wall moldings and trims at interfacement of ceiling with vertical surfaces and other interruptions using longest practical lengths. 1. Miter corners. 2. Include outside corner caps. 3. Attach to vertical surfaces with mechanical fasteners.

R. Install system to not restrict removal and reinstallation of acoustical panels with damage to panels or system.

3.3 TOLERANCES

A. Level main runners and cross tees to within 1/8 inch in 12 feet.

B. Maximum deflection for suspension system, including components, hangers, fastening devices, lighting fixtures, ceiling grilles and acoustical panels maximum L/360 of span.

3.4 ADJUSTING

A. Replace damaged units. Touch up minor scratches and spots to match finish with paint recommended by manufacturer.




END OF SECTION


SECTION 096513RESILIENT BASE AND ACCESSORIES


SECTION 096513 RESILIENT BASE AND ACCESSORIES

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Long roll type wall base. 2. Floor reducer and transition strips.

B. Related Sections: 1. Section 064100 - Architectural Wood Casework 2. Section 092900 - Gypsum Board 3. Section 096514 - Rubber Flooring and Stair Treads

1.2 REFERENCES


B. American Society for Testing and Materials (ASTM): ASTM F 1861- Standard Specification for Resilient Wall Base.

1.3 SUBMITTALS


B. Product Data: Published product characteristics, performance data, and specifications.

C. Samples: Provide complete line of color swatches from manufacturer's selection.

D. Samples: Provide sample illustrating selected colors.

E. Manufacturer's Instructions: Installation instructions, installation requirements, and perimeter conditions requiring special attention.

1.4 QUALIFICATIONS

A. Installer: Company specializing in work of this Section with minimum 5 years experience installing commercial quality work of comparable scope and quality specified for work of this Project.

1.5 MOCK-UPS


B. Provide sample installation of site-formed outside corner. Maintain approved mock-up in place as standard of quality for remaining installations.






B. Packaging: Deliver in original labeled carton.


A. Environmental Requirements: Maintain room temperature at not less than 70 degrees F for 24 hours prior to, during, and following installation.

B. Material Acclimation: Allow resilient base to acclimate for 24 hours before installation in room area conforming to environmental requirements.

1.8 MAINTENANCE


B. Maintenance Data: Manufacturer's cleaning and maintenance instructions.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Roppe 1. Tel (425) 776-8359, Fax (425) 771-5388, Cell (206) 227- 8035, Email

[email protected] (Olaf Vanluenen, CSI, Mfrs Rep). 2. Cell (206) 310-7504, Tel (800) 562-2857 / (206) 282-3770 Ext 1102, Fax (206) 281-

7612, Email [email protected] (T&A Supply, Jill Shaw). 3. Website http://www.tasupply.com / http://www.roppe.com

B. Johnsonite 1. Cell (206) 409-3870, Tel (253) 395-6287 #1685, Fax (253) 872-9022, Email

[email protected] (Pacific Mat, Nora Vivarelli CSI). 2. Website http://www.pacmat.com / http://www.johnsonite.com

C. Armstrong World Industries 1. Tel (800) 356-9301 Ext. 8975, Email [email protected] (Kim Shrader, Mfrs

Rep). 2. Cell (206) 409-3870, Tel (253) 395-6287 Ext 1685, Fax (253) 872-9022, Email

[email protected] (Nora Vivarelli CSI) 3. Website http://www.pacmat.com / http://www.armstrong.com

D. BurkeMercer 1. Tel (253) 796-3528 / (800) 878-6800, Pager (206) 917-1156, Cell (253) 219-3460

(Cronin Company, Greg Madsen). 2. Website http://www.burkemercer.com

E. Substitution Requests: Submit for approval under provisions of Section 012500.

2.2 RESILIENT BASE - GENERAL

A. Long Roll: Minimum 100 foot continuous base. No short lengths.

B. Height: 4 inch, except where 6 inch is shown on Drawings.




C. Gauge: 1/8 inch (0.125). Thinner 0.080 gauge not accepted.

D. Toe Types: 1. Style B - Coved toe at resilient flooring.

2.3 RUBBER BASE

A. Vulcanized resilient rubber with matt finish with solid color throughout material, ASTM F 1861 Type TS - Rubber, vulcanized thermoset. 1. Matt finish with solid color throughout material. 2. Type TV – Vinyl, Thermoplastic and Type TP – Rubber, Thermoset (vinyl/rubber

composite) bases are not accepted.

B. Products: 1. Roppe, Pinnacle Rubber Base. 2. BurkeMercer, BurkeBase Rubber Wall Base.

2.4 ACCESSORIES

A. Sealers, Fillers, Primers: Water-resistant type, as instructed by manufacturer.

B. Adhesives: As instructed by manufacturer. 1. Porous Surfaces: White acrylic cove base adhesive. 2. Non-Porous Surfaces: Contact bond adhesive.

C. Adhesives: Water-resistant type recommended by manufacturer to suit resilient products and substrate conditions indicated. 1. Use adhesives that comply with the following limits for VOC content when calculated

according to 40 CFR 59, Subpart D (EPA Method 24): a. Cove Base Adhesives: Not more than 50 g/L.

D. Other Materials: Provide incidental and accessory materials, tools, methods and equipment required for completion of resilient covering installations.

2.5 FINISHES

A. Resilient Base Color (RB): Johnsonite, 66 Either Ore.

B. Reducer/Transition Strip Color: Match base or as accepted by Architect.

PART 3 EXECUTION

3.1 EXAMINATION


B. Verify wall substrate installations free of voids and gaps, as necessary to provide solid backing behind resilient base installation.




3.2 PREPARATION

A. Remove grease, dust, dirt, and other foreign substances. Follow manufacturer's instructions.

B. Perform work as necessary under work of Section 092216, Section 092600, and Section 092900 to provide solid backing as substrate for work of this Section.

3.3 INSTALLATION

A. Install in accordance with manufacturer's instructions and provisions of Contract Documents.

3.4 RESILIENT BASE INSTALLATION

A. Install resilient base at wall perimeters of rooms and spaces to receive resilient flooring, carpeting, and other floors as indicated.

B. Provide around entire perimeter of rooms, including kick spaces at fixed casework.

C. Uncoil wall base 24 hours ahead of installation at room temperature to allow acclimation in the flat condition.

D. Install from ends toward center. Avoid stretching.

E. Using approved adhesives, cement directly to solid backing. Bond fully and tightly to wall and floor surfaces.

F. Fit joints for tight vertical joints.

G. Maintain minimum measurement of 18 inches between joints for resilient base and full length for resilient stringers where possible.

H. Install with no joints on a single wall less than 30 feet apart.

I. Corners: 1. Internal Corners: Mark, miter, and fold resilient base at corner. 2. External Corners: Mark and cut V into 2/3 thickness, and wrap resilient base around

corner. 3. Make relief cuts as necessary for smooth, even appearance. 4. Adhere with adhesive to hold permanently in place. 5. Premolded corner base are not accepted.

J. Scribe and fit to door frames and other interruptions.

3.5 REDUCER AND TRANSITION STRIPS

A. Reducing Strips: Install at terminations and unprotected or exposed edge transitions between out-of-plane finish flooring transitions.

B. Install in longest possible lengths with no length less than 4 foot long at single doors and 6 feet at double doors.




C. Fit with tight hairline joints between adjoining strips.

3.6 ADJUSTING

A. Replace wall base not uniformly adhered to wall, out of alignment, out of plumb, and where showing gaps, bulges and other installation defects.

3.7 CLEANING

A. After bases and reducer strips have set sufficiently, wash with neutral cleaner as recommended by manufacturer.

B. Leave surfaces smooth and clean, free of defects.

END OF SECTION



SECTION 096514RUBBER FLOORING

SECTION 096514 RUBBER FLOORING

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Rubber flooring. 2. Adhesives and accessories for complete installation.

B. Related Sections: 1. Section 061000 - Rough Carpentry 2. Section 092900 - Gypsum Board 3. Section 096513 - Resilient Base and Accessories

1.2 REFERENCES


B. ASTM International (ASTM): 1. ASTM C501 - Tabor Abrasion Test 2. ASTM C1028 - Standard Test Method for Determining the Static Coefficient

of Friction of Ceramic Tile and Other Like Surfaces by the Horizontal Dynamometer Pull-Meter Method

3. ASTM D2047 - Test Method for Static Coefficient of Friction of Polish-Coated Floor Surfaces as Measured by the James Machine.

4. ASTM D412 - Test Methods for Rubber Properties in Tension. 5. ASTM D570 - Test Method for Water Absorption of Plastics. 6. ASTM D2047 - Test Method for Static Coefficient of Friction of Polish-

Coated Floor Surfaces as Measured by the James Machine. 7. ASTM D2240 - Test Method for Rubber Property - Durometer Hardness. 8. ASTM E84 - Test Method for Surface Burning Characteristics of Building

Materials 9. ASTM E648 - Test Method for Critical Radiant Flux of Floor Covering

Systems Using a Radiant Heat Energy Source. 10. ASTM F1344 - Standard Specification for Rubber Floor Tile 11. ASTM F1869 - Standard Test Method for Measuring Moisture Vapor

Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride.

C. National Fire Protection Association (NFPA): NFPA 253 - Standard Method of Test for Critical Radiant Flux of Floor Covering System Using a Radiant Heat Energy Source.

1.3 SUBMITTALS


B. Product Data: Product literature including characteristics, specifications, physical properties, and performance criteria.

C. Samples: Flooring tile in accepted color, patterns, and thickness.




D. Manufacturer's Instructions: Include installation requirements, special procedures, and conditions requiring special attention.

E. Sample Warranty: Meet or exceed provisions specified by this Section.

1.4 MAINTENANCE DATA


B. Maintenance Data: Instructions for cleaning general care.


A. Hardness: ASTM D2240, Shore A, 87 percent.

B. Tensile Strength: ASTM D412, minimum 900 psi.

C. Elongation: ASTM D412, minimum 200 percent.

D. Water Absorption: ASTM D570, less than 0.3 percent.

E. Tabor Abrasion: ASTM C501, less than one gram loss, H-18 wheel, 5 gram load, 1000 cycles.

F. Slip-Resistance: ASTM D2047, static coefficient of friction of 1.00 for dry leather shoes and 0.90 on foam rubber and solid rubber shoes dry and wet, random sampling.

G. Critical Radiant Panel: ASTM E648, minimum 1.02 watts, Class 1.

H. Flamespread: ASTM E84, NFPA 253, maximum 0.25 rating, Class A.

I. Critical Radiant Flux Test: ASTM E648, Class 1.

J. Static Coefficient of Friction: ASTM D2047, 0.8-1.0.

K. Static Coefficient of Friction: Provide flooring materials with the following values as determined by testing according to ASTM C1028: 1. Level Surfaces: Minimum 0.6. 2. Ramp Surfaces: Minimum 0.8.


A. Installer Qualifications: 1. Company specializing in work of this Section with minimum of 3 years experience

installing commercial quality work of comparable scope. 2. Approved as qualified installer by manufacturer’s representative prior to Bid, or

accepted by Architect.


A. Conform to provisions of Section 016600 and manufacturer’s instructions.




B. Deliver in original cartons labeled with manufacturer’s name, product, and run number.

C. Store floor covering materials in dry place maintained at temperature of 50 degrees F to 90

degrees F for 48 hours before laying.

D. Handle to prevent breakage and discoloration.

1.8 PROJECT BUILDING CONDITIONS

A. Room Temperature: Maintain at minimum 70 degrees F for 48 hours before and during installation. Maintain at minimum 55 degrees F thereafter.

1.9 COORDINATION


B. Section 061000 for installation of rubber floor tile over plywood base.

C. Section 096513 for resilient base.

1.10 WARRANTIES


B. Manufacturer: Standard 10 year wear warranty for flooring.

1.11 EXTRA STOCK

A. Extra Stock: Furnish 3 rubber flooring tiles.

B. Obtain written receipt when delivered to Owner’s Representative.

PART 2 PRODUCTS

2.1 MANUFACTURER

A. Johnsonite, specified for type and quality. 1. Cell (206) 200-2439, Voice Mail (800) 899-8916 Ext 767, Email

[email protected] (Matt Barr, Sales Business Mgr). 2. Website: www.johnsonite.com

B. Roppe 1. Tel (425) 776-8359, Fax (425) 771-5388, Cell (206) 227- 8035, Email

[email protected] (Olaf Vanluenen, CSI, Mfrs Rep) 2. Cell (206) 310-7504, Tel (800) 562-285 / (206) 282-3770 Ext 1102, Email

[email protected] (T&A Supply, Jill Shaw). 3. Website: www.roppe.com.





2.2 MATERIAL

A. Composed of 100 percent synthetic virgin rubber, finely ground stabilizing fillers, migrating waxes and soil-releasing agents, high quality fade-resistance pigmentation with solid color throughout material, blended, calendared, and vulcanized, conforming to ASTM F1344.

2.3 RUBBER FLOOR TILES

A. Tile Flooring: Johnsonite, Hammered Surface Speckled Rubber Floor Tile (HRTSP), conforming to ASTM F1344 1. Thickness: 0.125 inches. 2. Size: 24 by 24 inches square. 3. Pattern: 20 Speckled, Roundel Artisan Collection 4. Finish: Roundel Artisan Collection, Manufacturer’s standard colors

2.4 ACCESSORIES

A. Leveling Compounds, Sealers, Fillers, and Primers: Water-resistant type, as supplied by or recommended by manufacturer.

B. Adhesives: Non-solvent base and as instructed by manufacturer for installation.

C. Adhesives: Contact adhesives and adhesive tapes as required to adhere work of this Section to substrate, as instructed by manufacturer.

D. Caulking Compound: Two-part epoxy for adhering nose of treads to stringers, as instructed by manufacturer.

E. Other: As instructed by manufacturer and as required to conform to manufacturers Warranty provisions.

PART 3 EXECUTION

3.1 EXAMINATION


B. Surfaces: Smooth, hard, stable, clean, and dry.

C. Plywood Substrate: Inspected by manufacturer's representative for moisture content. Do not proceed until floor has been certified as suitable by manufacturer's representative. 1. Alkalinity, Moisture and Adhesion Testing: Perform tests recommended by

manufacturer. Proceed with installation only after substrates pass testing.

3.2 PREPARATION

A. Remove grease, dirt, dust and other foreign substances from substrate surfaces. Follow Manufacturer's directions.




B. Level substrate surfaces not conforming to specified tolerances with underlayment per manufacturer’s recommendations.

3.3 INSTALLATION


B. Use trowel size for adhesives as instructed by manufacturer.

C. Make seams and joints snug and tight.

D. Roll flooring with 150 pound roller.

3.4 ADJUSTING

A. Repair or replace work of this Section that is not fully adhered to substrate, material with overlapping or open joints, and material damaged prior to Owner occupancy.

3.5 CLEANING

A. After adhesives have cured, clean work of this Section with a neutral cleaner following procedures as instructed by manufacturer.

3.6 PROTECTION

A. Cover flooring with undyed, untreated kraft paper prior to Owner occupancy.

B. Do not permit foot traffic for minimum 24 hours after installation and until adhesives have sufficiently cured.

C. Limit foot traffic and heavy loads.

3.7 FINISHING

A. After rubber flooring and stair tread adhesive have fully cured, clean with neutral cleaner using materials and procedures in accordance to manufacturer's instructions.

END OF SECTION


SECTION 096724RESINOUS MORTAR FLOORING


SECTION 096724 RESINOUS MORTAR FLOORING

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: Troweled urethane mortar flooring system with integral urethane base as part of Alternate No. 5 – Urethane Floor at Kitchen Areas

B. Related Sections: 1. Section 012300 - Alternates 2. Section 033000 - Cast- In- Place Concrete

1.2 REFERENCES

A. Reference Standards: Current edition at date of Project Manual, except as otherwise specified.

B. ASTM International (ASTM): 1. ASTM C307 - Standard Test Method for Tensile Strength of Chemical-

Resistant Mortar, Grouts, and Monolithic Surfacings 2. ASTM C413 - Standard Test Method for Absorption of Chemical- Resistant

Mortars, Grouts, and Monolithic Surfacings and Polymer Concretes

3. ASTM C531 - Standard Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical- Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes

4. ASTM C579 - Standard Test Methods for Compressive Strength of Chemical- Resistant Mortars, Grouts, Monolithic Surfacings and Polymer Concretes

5. ASTM C580 - Standard Test Method for Flexural Strength and Modulus of Elasticity of Chemical- Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes

6. ASTM C1028 - Standard Test Method for Determining the Static Coefficient of Friction of Ceramic Tile and Other Like Surfaces by the Horizontal Dynamometer Pull- Meter Method

7. ASTM D635 - Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

8. ASTM D2047 - Standard Test Method for Static Coefficient of Friction of Polish- Coated Flooring Surfaces as Measured by the James Machine

9. ASTM D2240 - Standard Test Method for Rubber Property—Durometer Hardness

10. ASTM D4060 - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser

11. ASTM D4226 - Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products

12. ASTM D4541 - Standard Test Method for Pull- Off Strength of Coatings Using Portable Adhesion Testers




1.3 SUBMITTALS


B. Product Data: Published literature shown performance characteristics, physical properties, and limitations. Include typical details and solutions for joints, cracks, and

C. Samples: Actual materials approximately 6 inch square illustrating full range of colors and appearance.

D. Certificates: Installer as trained and authorized to install manufacturer’s system.

E. Manufacturer's Instructions: Include installation instructions, special procedures, and perimeter conditions requiring special attention.

F. Sample Warranty: Meet or exceed provisions specified by this Section.

1.4 CLOSEOUT SUBMITTALS


B. Maintenance Instructions to Owner's Personnel: Conform to Section 017823


A. Manufacturer: Company specializing in work of this Section with minimum 3 years documented manufacturing experience.

B. Installer: 1. Company specializing in work of this Section with minimum 3 years documented

experience of comparable scope.2. Trained and authorized by manufacturer prior to Bid Date.


A. Static Coefficient of Friction: Provide flooring materials with the following values as determined by testing according to ASTM C1028: 1. Level Surfaces: Minimum 0.8.

1.7 MOCK-UPS

A. Provide under Quality Assurance provisions of Section 014300.

B. Locate minimum 8 square foot mock-up as instructed by Architect and as required to illustrate system.

C. Verify mock-up as conforming to manufacturer’s instructions and provisions of Contract Documents.

D. Remove mock-ups that are not accepted, and protect and maintain accepted mock-up as standard of quality for work of this Section.




E. Do not incorporate accepted mock-up into work of this Section.


A. Arrange, in accordance with Section 013119.

B. Attendance: Contractor, installer, Owner, Architect, manufacturer’s representative, and those requested to attend.

C. Meeting Time: Minimum 3 weeks prior to prior to beginning work of this Section and work of related Sections affecting work of this Section.



A. Conform to provisions of Section 016600 and manufacturer’s instructions.

B. Deliver to project site in manufacturer’s protective packaging with identifying labels intact and legible.

C. Store with an enclosed space at temperatures between 60 to 80 degrees F. Protect from moisture, dampness, direct UV radiation, freezing, and construction activities.


A. Temperature of Substrate and Material: Maintain between 60 and 85 degrees F. Do not install where floor temperatures will exceed 140°F on a continuous basis.

B. Moisture: Do use water or steam in vicinity during application.

1.11 COORDINATION


B. Section 033000 for concrete slab finishing, tolerances, and repair of concrete substrates out of tolerance.

1.12 WARRANTIES


PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Stonhard, specified for type and quality. 1. Tel (503) 410- 1263, Email [email protected] (Kevin Boyd). 2. Website http://www.stonhard.com

B. Substitution Requests: Conform to provisions of Section 012500.




2.2 MATERIALS

A. Product: StonClad UT 1. General: a high performance, four- component mortar consisting of urethane resin,

curing agent, pigments, selected, graded aggregates, a two- component, high performance, pigmented urethane sealer.

B. Mortar Base (StonClad UT): 1. Resin: Urethane 2. Formulation Description: Four- component mortar consisting of urethane resin, curing

agent, pigments and graded quartz aggregates. 3. Type: Pigmented mortar 4. Application Method: Notched trowel 5. Application thickness: ¼”

C. Sealer (StonClad UT Sealer): 1. Resin: Polyurethane 2. Formulation Description: Two- component, high performance, urethane sealer. 3. Type: Pigmented 4. Finish: Gloss 5. Number of Coats: 1

D. Surface Texture: 1. Provide “Light” texture to conform with specified Static Coefficient of Friction.

E. Coved Base/Vertical Surfaces: 1. Stonclad UR with Stonclad UT Sealer: Four- component mortar consisting of urethane

resin, curing agent, selected, graded aggregates blended with inorganic pigments, a two- component, high performance, pigmented urethane sealer as manufactured and installed by Stonhard. Apply over concrete curb.

2.3 EQUIPMENT

A. Mixing and Application Equipment: Conform to manufacturer’s instructions.

2.4 ACCESSORIES

A. Primers and Sealers: As instructed by manufacturer.

B. Patching and Fill Material: Resinous product as instructed by manufacturer for specific application.

C. Joint Sealant: As specified in Section 079200.

2.5 FINISHES

A. Colors: As accepted by Architect from manufacturer’s standard selection.




PART 3 EXECUTION

3.1 EXAMINATION

A. Verify conditions as satisfactory to receive work of this Section before beginning.

B. Concrete Substrate Surface: 1. Dry and free of all wax, grease, oils, fats, soil, loose or foreign materials, and laitance. 2. Open pores throughout and have a sandpaper texture.

C. Temperature of Substrate and Flooring Ingredients: Verify in conformance to provisions of this Section and manufacturer’s instructions.

D. Moisture Testing Test horizontal substrates to determine acceptable dryness. Test method as recommended by resinous flooring manufacturer. 1. Perform in situ probe test, ASTM F 2170. Proceed with application only after

substrates do not exceed a maximum potential equilibrium relative humidity of 85 percent.

2. Perform anhydrous calcium chloride test, ASTM F 1869. Proceed with application only after substrates have maximum moisture- vapor- emission rate of 6 lb per 1,000 sq. ft. per 24 hours.

3. Perform additional moisture tests recommended by manufacturer. Proceed with application only after substrates pass testing.

3.2 PREPARATION

A. Protection: Cover adjacent surfaces as necessary to protect from damage by installation of this work.

B. Substrate Preparation: 1. Remove laitance and unbonded cement particles using mechanical methods, including

abrasive blasting or scarifying.2. Remove bond breakers and other contaminants by scrubbing with a heavy- duty

industrial detergent (Stonhard, Stonkleen DG9) and rinsing with clean water.

C. Crack Treatment materials: Isolate and reinforce concrete substrate floor cracks 1/8 inch or greater, conforming to manufacturer’s instructions and details.

D. Priming: Conform to manufacturers instructions.

3.3 INSTALLATION


B. Mixing: 1. General: Mix components until consolidated only in amounts that can be applied

within recommended application life.2. Discard materials not used within application life.

C. System Application: 1. General: Apply each component of resinous flooring system in compliance with

manufacturer's written directions to produce a uniform monolithic wearing surface of




thickness indicated, uninterrupted except at divider strips, sawn joints or other types of joints (if any), indicated or required.

D. Resinous Flooring: 1. Troweled Mortar: Mix mortar material according to manufacturer's recommended

procedures. Mix mortar material according to manufacturer's recommended procedures. Uniformly spread mortar over substrate at manufacturer’s recommended height using specially designed trowel.

2. Trowel and finish to 1/4 inch uniform thickness using steel finishing trowels and power trowels a to compact and smooth surface of flooring material.

3. Hand tool edges and confined areas. Hand screed material at 5/16 inch. Then, compact to 1/4 inch thickness. Make smooth uniform surface free of trowel marks and ridges.

4. Broadcast graded quartz aggregate texture directly into mortar base. 5. Finish Sealer: Vacuum the floor surface. Mix and apply sealer with strict adherence to

manufacturer's installation procedures.

E. Cove Base/Vertical Surfaces: 1. Mix and apply cove base mortar in conjunction with mortar base of resinous flooring at

the height indicated on Drawings and/or Finish Schedule.

F. Surface Texture: 1. Apply Finish Sealer at a rate to achieve a surface finish that matches samples

submitted.

G. Cure Rate: 1. 8 hours for foot traffic at 77 degrees F.2. 24 hours for moderate wheeled operations. 3. 48 hours for common industrial spillages and heavy traffic. 4. 72 hours for strong chemical spillages.

3.4 FIELD QUALITY CONTROL

A. Manufacturer’s Field Service: Attend meetings and make interim and final inspections to verify conformance of installation as conforming to manufacturer instructions.

3.5 ADJUSTING

A. Inspect and make adjustments after installation.

B. Repair or replace defective work.

3.6 CLEANING

A. Leave installations clean and premises free from residue and debris from work of this Section.

3.7 PROTECTION

A. Take measures to protect flooring system from damage due to construction activities prior to Substantial Completion.




B. Cover flooring with plywood in areas subject to impact and rolling loads.

END OF SECTION


SECTION 097723FABRIC-WRAPPED PANELS


SECTION 097723 FABRIC-WRAPPED PANELS

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Sound-absorbing fabric-wrapped fiberglass acoustical wall panels.

B. Related Sections: 1. Section 092216 - Non-Structural Metal Framing 2. Section 095300 - Acoustical Ceiling Suspension Assemblies 3. Section 092900 - Gypsum Board

1.2 REFERENCES


B. ASTM International (ASTM): 1. ASTM E84 - Test Method for Surface Burning Characteristics of Building

Materials 2. ASTM C423 - Test Method for Sound Absorption and Sound Absorptive

Coefficients by the Reverberation Room Method.


A. Sound-absorbing Panels Noise Reduction Coefficient (NRC): Minimum NRC 0.80, 2 inch thick semi-rigid fiberglass core panels, tested to ASTM C423 with Type A mounting.

1.4 SUBMITTALS


B. Shop Drawings: Locations, elevations, dimensions, configurations, installation attachment methods, and joint treatment at abutting panels.

C. Product Data: Acoustical performance characteristics, panel composition, components, and acoustically porous fabric.

D. Samples: Sample of each acoustical panel type.

E. Manufacturer's Instructions: Include installation instructions, special procedures, and conditions requiring special attention.

1.5 QUALIFICATIONS

A. Installer: 1. Company specializing in work of this Section with minimum 5 years documented

experience installing commercial quality work of comparable scope. 2. Authorized installer by manufacturer.




1.6 MOCK-UPS

A. Install mock-up panels to show typical construction and reveals between panels.

B. Approved mock-up may remain in place.



B. Fire Rating: Components and system, Tested ASTM E84. Fire Hazard Classification: IBC / UL Class A. 1. Flame Spread Rating: Less than 25. 2. Smoke Developed: Less than 450.



B. Store materials off ground. Cover and protect from dirt and dust contamination.

C. Handle materials in a manner that will protect them from damage and soiling.

1.9 ENVIRONMENTAL CONDITIONS

A. Ambient Temperature and Humidity: Continuously maintain building space temperatures range between 60 degrees F to 80 degrees F and relative humidity not more than 80 percent.

B. Building: Fully enclosed, wet work complete.

1.10 COORDINATION


B. Section 095300 for installation of acoustical panels into ceiling tee-bar grid system

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Snap-Tex Northwest Inc. 1. Tel (206) 789-2413, Fax (206) 789-3699, Email [email protected] (Ken Huber

CSI, Alvin Wolberg) 2. Website http://www.snaptex.com

B. Wall Technology, Inc. 1. Tel (425) 277-0631, Fax (425) 277-5446, Email [email protected] Schwarz &

Associates, Andy Schwarz, Jerald Schwarz). 2. Website http://www.walltechnology.com

C. Fabri-Mate Systems Inc.




1. Tel (866) 622-2996 / (805) 642-7470, Fax (805) 642-3154 2. Website: http://www.fabricmate.com

D. Decoustics 1. Tel/Cell (253) 333-6564, Fax (253) 333-6517, Email [email protected] (Don King,

Creative Design Concepts). 2. Tel (800) 387-3809, Email [email protected] (John Balog, Vice-President Sales &

Mktg). 3. Website http://www.decoustics.com

E. Sound Concepts 1. Tel (425) 424-0551, Fax (425) 424-3531, Email [email protected] (Doug Turner

CSI). 2. Tel (204) 783-6297 (Richard Anthony, Sales Mgr). 3. Website http://www.soundconceptscan.com

F. Kinetics Noise Control 1. Cell (206) 818-8840, Tel (425) 497-0660, Fax (425) 867-5542, (David Forrest, Seattle

Sound and Vibration) 2. Website: www.seavib.com / http://kineticsnoise.com

G. Substitution Requests: Conform to provisions of Section 012500.

2.2 SOUND-ABSORBING FABRIC WRAPPED FIBERGLASS ACOUSTICAL PANELS

A. Tackable Fiberglass Acoustical Panel Core: 1. Minimum 6 to 7 pcf density dimensionally stable rigid tackable fiberglass. 2. Resin hardened edges.

a. Horizontal: Square b. Vertical: Bevel front face 1/4 inch.

B. Panel Finish Fabric 1. Acoustically Porous Fabric: 100 percent recycled polyester, unbacked, Class A tested

ASTM E84. 2. Fabric shall cover face, edges, and a return on the back of a minimum of 1-1/2 inches.

C. FWP-1: 1. 4 inch thick core 2. Fabric:

a. Manufacturer: Architex b. Pattern: Sprinkle c. Color: Tangerine

D. FWP-2: 1. 1 inch thick core 2. Fabric:

a. Manufacturer: Architex b. Pattern: Sprinkle c. Color: Tangerine

E. FWP-3: 1. 1 inch thick core




2. Fabric: a. Manufacturer: Carnegie b. Pattern: Strie 6423 c. Color: 129

2.3 ACCESSORIES

A. Mounting Accessories: Impaling clip system adhered with construction adhesive, used in conjunction with security leveling clips approximately matching color of panel fabric, and as instructed by manufacturer for permanent mounting to prevent dislodgement due to impact.

B. Metal Clips or Bar Hangers: Manufacturer's standard two-part metal "Z" clips, with one part of each clip mechanically attached to back of panel and the other part to substrate, designed to permit unit removal.

C. Hook-and-Loop Strips: Manufacturer's standard Velcro type fasteners.

2.4 FABRICATION

A. Fabricate in sizes as detailed, and as necessary to provide clean square lines and joints with edges of adjacent panels in alignment.

PART 3 EXECUTION

3.1 EXAMINATION

A. Verify conditions ready to receive work of this Section before beginning work.

B. Verify space enclosed and weathertight, painting and other wet work complete and dry, dust generating work and overhead work complete.

3.2 PREPARATION

A. Field measure and verify wall areas to receive acoustical panels. Establish exact layout of units.

3.3 INSTALLATION


B. Mount according to manufacturer's instructions for uniform appearance. Make panel installation plumb and aligned with joints and edges straight and true to line.

C. Install using fastening system as instructed by manufacturer.

3.4 ADJUSTING

A. Make adjustments as necessary to align panels visually and to make fastening systems secure.




B. Trim fabric and remove loose threads.

C. Repair or replace panels where fabric or plastic facing is not adhered or is damaged.

3.5 CLEANING

A. Clean exposed surfaces of acoustical wall panels.

END OF SECTION


SECTION 098116ACOUSTICAL INSULATION


SECTION 098116 ACOUSTICAL INSULATION

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Acoustical wall cavity fiberglass batt insulation

B. Related Sections: 1. Section 061000 - Rough Carpentry 2. Section 062000 - Finish Carpentry 3. Section 072116 - Blanket Insulation 4. Section 092216 - Non Structural Metal Framing 5. Section 092900 - Gypsum Board

1.2 REFERENCES


B. American Society for Testing and Materials (ASTM): 1. ASTM C665 - Standard Mineral Fiber Blanket Thermal Insulation for Light

Frame Construction and Manufactured Housing. 2. ASTM C423 - Standard Test Method for Sound Absorption and Sound

Absorption Coefficients by the Reverberation Room Method. 3. ASTM C1338 - Standard Test Method for Determining Fungi Resistance of

Insulation Materials and Facings. 4. ASTM E84 - Standard Test Method for Surface Burning Characteristics of

Building Materials. 5. ASTM E96 - Standard Test Methods for Water Vapor Transmission of

Materials. 6. ASTM E795 - Standard Practices for Mounting Test Specimens During

Sound Absorption Tests.


A. Acoustical Insulation: 1. Fiberglass batt and blanket insulation used at acoustical interior partition walls.

1.4 SUBMITTALS


B. Shop Drawings: 1. Show extent of acoustical insulation on floor plan.

C. Product Data: Published performance characteristics and properities showing conformance to this Section. 1. Sound Absorptive Coefficients.




D. Manufacturer's Instructions: Indicate installation requirements, special procedures, and conditions requiring special attention.

1.5 QUALIFICATIONS

A. Installer: Company specializing in work of this Section with minimum 3 years documented experience.



B. Deliver in manufacturer's original labeled package indicating R-Value, thickness, and density.

C. Store in clean, dry place and handle to prevent tearing material.

PART 2 PRODUCTS

2.1 INSULATION MANUFACTURERS

A. Johns Manville 1. Tel (425) 391-0119, Fax 425-391-5999, Cell (206) 409-5650, Email [email protected]

(John Robinson CSI, Mfrs Rep). 2. Tel (800) 654-3103 (Information Center). 3. Website http://www.jm.com

B. Knauf Fiber Glass 1. Cell (360) 907-5185, (360) 834-4932, Email [email protected] (Francis

Cloudt, Area Manager). 2. Cell (206) 391-0835, Tel (425) 488-7600 Ext 111, Fax (425) 488-7827, Email

[email protected] (Steve Thompson, Gen Mgr, R-Factor). 3. Tel (800) 825-4434 Ext 8212. 4. Website http://www.knaufusa.com

C. Owens Corning 1. Tel (425) 497-0660, Fax (425) 867-5542, (Seattle Sound and Vibration, Dave Forrest

Cell (206) 396-6885), Website http://:www.forrestsound.com 2. Voice Mail (800) 773-1551 Maylene Hugh, Marketing Development Mgr), Website

http://www.owenscorning.com

D. Substitution Requests: Conform to provisions of Section 012500.

2.2 BATT AND BLANKET ACOUSTICAL INSULATION

A. Unfaced, friction fit glass fiber batt insulation is accepted for sound insulation with tested NRC coefficients. Provide in thickness to fill full width of studs at interior partitions, except where otherwise indicated by Wall Type Schedule.




2.3 FIBERGLASS SOUND BLANKET

A. Wall Cavity Insulation: Johns Manville, ComfortTherm, Poly-Encapsulated Fiber Glass Acoustical Insulation, Formaldehyde Free. 1. Insulation: ASTM C665, Type II, Class A, Category 1 2. Film Permeability: ASTM E96.

a. Facer Film: 0.5 perms b. Perforated Backer Film: 25 perms

3. Thickness: 3-1/2 inch 4. Width: 16 inch 5. Noise Reduction Coefficient (NRC): 0.90, ASTM E795, Type E-405 Mounting

PART 3 EXECUTION

3.1 INSTALLATION


B. Wall Cavity Insulation: 1. Install friction fit unfaced batt insulation to completely fill width of stud and furring

system space, except as otherwise indicated by Wall Type Schedule. 2. Install insulation to provide continuity of insulating layer. Completely fill spaces within

insulating cavity. Do not compress insulation. 3. Install insulation tightly around electrical outlets, switches, and other wall and ceiling

penetrations. Seal joints. 4. When installed at walls in heights over 8 foot, provide supplementary support to hold

unfaced friction fit insulation in place.

END OF SECTION


SECTION 099000PAINTING AND COATING


SECTION 099000 PAINTING AND COATING

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Surface preparation. 2. Field applied primers and sealers. 3. Field applied coatings and paints. 4. Schedule at end of this Section.

B. Shop Preparation and Primers for Metal: Specified Section 055000 - Metal Fabrication.

C. Related Sections include but are not limited to following: 1. Section 012300 - Alternates 2. Section 033000 - Cast-In-Place Concrete 3. Section 051200 - Structural Steel Framing 4. Section 052119 - Open Web Steel Joist Framing 5. Section 053100 - Steel Deck 6. Section 055000 - Metal Fabrications 7. Section 061000 - Rough Carpentry 8. Section 061800 - Glue Laminated Construction 9. Section 062000 - Finish Carpentry 10. Section 064100 - Architectural Wood Casework 11. Section 079200 - Joint Sealants 12. Section 081113 - Hollow Metal Doors and Frames 13. Section 083113 - Access Doors and Frames 14. Section 092900 - Gypsum Board 15. Section 104413 - Fire Protection Cabinets 16. Division 21 - Fire Suppression 17. Division 22 - Plumbing 18. Division 23 - Heating, Ventilating, and Air Conditioning 19. Division 26 - Electrical

1.2 REFERENCES


B. American Society for Testing and Materials (ASTM)International: 1. ASTM D523 - Standard Test Method for Specular Gloss. 2. ASTM D6763 - Standard Guide for Testing Exterior Wood Stains. 3. ASTM D5324 - Standard Guide for Testing Water-Borne Architectural

Coatings. 4. ASTM D6386 - Standard Practice for Preparation of Zinc (Hot-Dip

Galvanized) Coated Iron and Steel Hardware Surfaces for Painting.

C. United States Environmental Protection Agency (EPA):




1. EPA 40 CFR Part 59 (AD-FRL-6149-71RIN 2060 - National Volatile Organic Compound Emission Standards for Architectural Coatings, Final Rule, Federal Register/Vol. 63, No.176, September 11, 1998/Rules and Regulations.

2. Website http://www.epa.gov/ttn/uatw/183e/aim/fr1191.txt

D. Green Seal: www.greenseal.org 1. GS-11: Green Seal Environmental Standard for Paints and Coatings

E. Society for Protective Coatings (SSPC) - Systems and Specifications: http://www.sspc.org/ 1. Surface Preparation Standards and Specifications:

a. SSPC-SP 1: Solvent Cleaning b. SSPC-SP 2: Hand Tool Cleaning c. SSPC-SP 3: Power Tool Cleaning d. SSPC-SP 6: Commercial Blast Cleaning e. SSPC-SP 10: Near White Blast Cleaning f. SSPC-SP11: Power Tool Cleaning to Bare Metal

F. The Master Painters Institute (MPI): Tel (888) 674-8937, Fax (888) 211-8708, Email [email protected], Website http://www.paintinfo.com (Bob Welch, Technical Director). 1. MPI Architectural Painting Specification Manual (ASPM)

1.3 DEFINITIONS

A. DFT: Dry Film Thickness.

B. MSDS: Material Safety Data Sheet.

C. WFT: Wet Film Thickness.

1.4 SUBMITTALS


B. Product Data: Submit complete list of manufacturers and products including Product Data Sheets and MSDS. Arrange in same format as scheduled this Section. Include performance characteristics, limitations, and volatile organic compounds (VOC) emissions information.

C. Color Samples: Size not less than 8 inch by 10 inch draw-down for each color selected for final acceptance prior to beginning work. 1. Label back of each drawdown with manufacturer, product, color name and number,

and gloss level. 2. Furnish additional samples as required for acceptance of colors, finishes, and

textures. 3. Retain approved samples for reference.

D. Sample Warranty: Meet or exceed provisions specified by this Section.

1.5 CLOSEOUT SUBMITTALS





B. Maintenance Data: Product data sheets, manufacturer’s application instructions, MSDS, product color name and number, cleaning instructions, and touch-up and repaint instructions.


A. Single Source Responsibility: Supply primers, intermediate, and finish coats for each paint and coating system from single manufacturer, except as otherwise specified.

B. Product Listings: Acceptance based upon Approved Product List and as specified by this Section to make complete product line for each manufacturer. Where no product is listed for accepted manufacturer, verify with Architect before proceeding.

C. Surface Preparation: Conform to SSPC, manufacturer’s instructions, MPI Level 2 and 3, and these specifications. 1. Remove bond breakers, dust, foreign matter, and surface irregularities. 2. Prepare to prevent bleed-through of substrate material.

D. Paint System Application: Conform to manufacturer’s instructions. 1. Paint Grade: Conform to Premium Grade, except as otherwise specified.

a. Minimum one primer coat and two finish coats, except as otherwise specified. b. Additional coats as necessary to cover with no holidays or other surface

imperfections. 2. Dry film thickness (DFT) and wet film thickness (WFT), as instructed by manufacturer.

E. Painting Inspection: 1. The Owner may retain a Painting Inspection Agency to monitor the Contractor’s

painting operations. The Contractor shall permit access to the building to allow Owner’s painting inspector to perform activities that may include, but not limited to the following: a. Attend preconstruction meeting, make inspection of substrates prior to application

of paints and coatings, make intermittent inspections, and make final inspection based on requirements of manufacturer’s instructions.

b. Make report to Architect indicating defects and action required where inspection indicates non-compliance.

2. Contractor: Notify Owner one week prior to beginning work of this section so Owner can notify Painting Inspection Agency.

1.7 QUALIFICATIONS

A. Applicator: 1. Able to document minimum 10 years continuous experience in commercial quality

projects of similar type and scope. 2. Member of Painting and Decorating Contractors of America (PDCA), Master Painters

Institute (MPI), or accepted by Architect. 3. Employ qualified journeymen painters with apprentices under direction of qualified

journeymen, conforming to trade regulations.






B. Volatile Organic Compounds (VOC) Emissions: Conform to Green Seal Standard GS-11 http://www.greenseal.org/standards/paints.htm and US Environmental Protection Agency (EPA).

1.9 MOCK-UPS


B. Apply paint minimum 10 square foot area mock-ups for each accepted color and substrate type. Notify Architect when mock-ups are ready to review.

C. Install mock-ups after acceptance of submittals.

D. Located mock-ups as accepted by Architect.

E. Protect and retain accepted mock-ups as standard of quality for work of this Section.

F. Accepted mock-up may be incorporated into finished work.


A. Arrange under provisions of Section 013119.

B. Attendance: Contractor, painting subcontractor, Owner, Architect, manufacturer’s technical representative, Painting Inspection Agency, and others as requested to attend.

C. Meeting Time: Minimum 2 weeks before beginning work of this Section and work of related Sections affecting work of this Section, as required to meet Project Schedule.




B. Deliver in unopened, sealed containers, bearing manufacturer's original labels with manufacturer’s brand name, product name and number, color designation, surface preparation, mixing and reducing instructions, coverage, drying time, clean-up instructions, MSDS, and VOC content.

C. Store and utilize paint in original containers bearing manufacturer’s label for ease of identification. Do not put paint in containers bearing labels for other products.

D. Store at ambient temperature between 45 degrees F and 90 degrees F. Store and mix material outside building.

E. Take special safety precautions against hazards from toxic and flammable materials.

F. Place paint and solvent contaminated cloths and materials, subject to spontaneous combustion, in containers and remove from job site each day.




1.12 PROJECT SITE CONDITIONS

A. Environmental Requirements: Apply paints and coatings at surface and air temperatures above 45 degrees F and rising.

B. Weather: Do not apply exterior coatings when precipitation is predicted or is imminent.

C. Ventilation: Maintain continuous air exchange ventilation. Move moisture, odors, and fumes from painting to outside of building.

D. Illumination: Maintain lighting level of 50 foot candles measured at mid height at substrate surfaces.

1.13 WARRANTY


B. Manufacturer: 5 year materials Warranty.

C. Contractor: Furnish a 2-year labor and material maintenance bond. Defect correction will be promptly addressed following the specifications.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Benjamin Moore / Coronado 1. Tel (800) 642-5678 Ext 2217, Fax (503) 263-3849, Cell (503) 318-8046 Email

[email protected] (Randy Tessman, Architectural Rep). 2. Website http://www.benjaminmoore.com / http://www.coronadopaint.com/

B. Kelly-Moore Paint Company / RPM Company, Rust-Oleum 1. Tel (425) 260-2619, email [email protected] (Holly Davidson) 2. Tel (888) 677-2468 (Technical Hot Line). 3. Website http://www.kellymoore.com

C. Glidden Professional Paints 1. Cell (206) 354-0179, Fax (425) 413-2835, Email

[email protected] (Terry Decker, CSI, Architectural/Engineering Representatives).

2. Website https://www.gliddenprofessional.com/home.do

D. Parker/ Comex Group 1. Cell (206) 450-7342, Fax (425) 486-6155, Email [email protected] (Mike

Murphy, Architectural Sales Rep). 2. Website http://www.parkerpaint.com

E. PPG Industries, Inc/ Pittsburgh Paints. 1. Web Site http://www.pittsburghpaints.com

F. Sherwin-Williams Company




1. Tel (425) 427-1900 Ext 104, Fax (425) 427-1911, Cell (425) 417-1765, Email [email protected] (Brian Keil, CSI, CCPR).

2. Website http://www.sherwin-williams.com

G. Tnemec Company, Inc. 1. Tel (206) 762-5755 #3, Fax (206) 767-7588, Email [email protected] 2. Website http:www.tnemec.com

H. Substitution Requests: Submit for acceptance under provisions of Section 012500.

2.2 MATERIALS

A. Painting and Coating Schedule: Refer to Schedule at end of this Section for products specified for specific finishes.

B. Surfaces Not Scheduled for Paints and Coatings: Where unscheduled surfaces are discovered following Bid, assume premium commercial quality paint or coating and as instructed by manufacturer’s technical representative. Submit to Architect for acceptance prior to beginning work.

C. Coatings: Ready mixed, except catalyzed coatings. Process pigments to consistency for uniform and homogeneous coatings, good flow and brushing qualities, drying or curing free of streaks and sags.

2.3 GLOSS AND SHEEN LEVELS

A. Conform to Gloss and Sheen Levels as tested in accordance with ASTM D523, regardless of that stated by manufacturer product data and shown on paint containers.

GLOSS AND SHEEN LEVELS UNITS AT 60 DEGREES UNITS AT 85 DEGREES

G1 Matte or Flat 0 to 5 10 Maximum G2 Low Sheen / Velvet 0 to 10 10 to 35 G3 Eggshell 10 to 25 10 to 35 G4 Satin 20 to 35 35 Minimum G5 Semi-Gloss 35 to 70 (N/A) G6 Gloss 70 to 85 (N/A) G7 High Gloss More than 85 Units (N/A)

2.4 FINISHES AND COLORS

A. Field Painting Product Systems and Gloss Levels: As scheduled in this Section.

B. Paint and Stain Colors: Listing of paint manufacturer’s color does not constitute acceptance of paint manufacturer or product. 1. P-1: PPG, 541-2, Glistening Frost. 2. P-2: Not Used. 3. P-3: ICI Paints, A1833, Forest Black. 4. P-4: Kelly Moore, KM3829-2, Grey Matters. 5. P-5: PPG, 327-7, Burled Redwood.




PART 3 EXECUTION

3.1 EXAMINATION

A. Verify conditions ready to receive work of this Section before beginning work. Report to the general contractor unsatisfactory conditions or noncompliant work of other trades.

B. Arrange for adequate lighting, temporary heat, and ventilation.

C. Maximum Moisture Content of Substrates: Conform to manufacturer’s instructions. Perform tests using commercial quality electronic moisture meter. Where exceeding following values, promptly notify Architect and obtain direction before beginning work. 1. Exterior Wood: 17 percent. 2. Interior Wood: 10 percent. 3. Interior Finish Detail Woodwork, Including Trim, and Casework: 10 percent. 4. Plaster and Gypsum Materials: 6 to 7 percent.

D. The start of application shall mean the Contractor and Applicator fully accept conditions and substrates for the successful performance of the coating systems.

3.2 MATERIALS TO BE PAINTED

A. Prepare and finish all surfaces of materials, except as specifically excluded or otherwise specified.

B. Include Structural, Mechanical, and Electrical Items in rooms and spaces scheduled for painting. Paint out conduit and other such items to match color of adjacent surfaces.

C. Field paint exposed features and elements, including pre-finished items, such as conduit, ductwork, including exposed roof-top mounted mechanical equipment, hangers and seats, structural steel, secondary steel, panels, grilles, and surfaces visible through vents and louvers, whether indicated or not, except where specifically excluded by Contract Documents.

3.3 MATERIALS NOT TO BE PAINTED

A. Refer to Finish Schedule for rooms or areas not required to be field painted.

B. Metals: Brass, bronze, copper, stainless steel, pre-finished metal, and plated metals other than galvanized metal, except as specifically indicated.

C. Plastic laminate, melamine, and other finished plastic surfacing.

D. Glass and clear plastic, except as otherwise indicated.

E. Substrates with specified factory-applied colored finishes and normally unfinished substrates: 1. Includes: Door hardware, electrical switch plates, fabrics, tackboards, porcelain

enameled metal fabrications, insulated metal wall panels, and lighting fixtures. 2. Exception: Wire mold and other normally prefinished items mounted on surfaces

receiving coatings: Paint out to match and blend with field surface.




F. Inaccessible materials permanently enclosed behind building construction and structural components.

G. Exposed concrete with plywood form finish and concrete with sandblast finish.

H. Interior structural wood members including exposed dimensional lumber and plywood at Office areas. (See Paragraph 3.5 for surface preparation of interior structural wood members.) Interior glued-laminated beams at Office areas shall receive sealer per schedule in Part 3 of this section.

3.4 SURFACE PREPARATI0N UNDER WORK OF OTHER SECTIONS

A. Field Substrate Preparation Specified Under Work of Related Sections: Work of other sections will be complete leaving the surfaces ready to paint except for very minor touch up not including trade damage.

B. Shop Preparation and Primers for Metal Fabrications: Specified under work of Section 051200, 052119, 053100 and 055000, except for spot priming and touch-up of shop primers prior to applying finish coats specified under this Section.

3.5 SURFACE PREPARATION PROCEDURES

A. Conform to: Where in conflict the most stringent shall apply. 1. SSPC- Surface Preparation Procedures. 2. Manufacturer instructions. 3. Contract Document provisions. 4. MPI

B. Mildew Removal: 1. Do not use bleach to remove mold from carbon-based materials. These include paper,

cellulous, wood, sucrose (sugar), gypsum board, and materials that are considered food for mold.

2. Contact Owner and Architect for remediation method for mold contamination of carbon-based materials.

3. Proceed with methods to remove stains as specified for non-carbon based materials.

C. Steel and Iron: Put in condition to receive paint. Remove grease, rust, scale, dirt, and dust. Use prime paints compatible with finish coats. 1. Field Welded or Abraded Spots: Power tool, clean, and prepare, conforming to SSPC-

SP-3. Spot prime by end of same day. 2. Surfaces Shop Primed Conforming to Section 055000: Solvent clean free of oil and

grease before coating, conforming to SSPC-SP-1. 3. Surfaces Shop Primed with Alkyd Coatings and Coatings not Conforming to Section

051200, 052119, 053100 and 055000: a. Machine clean to SSPC SP-3. b. Power tool clean to SSPC SP-3 as required for removal of rust and scaling at

difficult to reach locations. c. Solvent clean free of oil and grease before coating, conforming to SSPC-SP-1.

4. Surfaces Not Previously Shop Primed: a. Remove Rust and Scale: Power tool clean and prepare, conforming to SSPC-SP-3.

Apply prime coat when thoroughly dry and before forming of visible rust.




b. Oil and Grease: Solvent clean, conforming to SSPC-SP-1, before applying finish coat.

D. New Factory Preprimed and Factory Prefinished Metals: Solvent clean in accordance with SSPC-SP-1 and apply bonding primer.

E. Uncoated, Ungalvanized, and Existing Ferrous Metals: Power tool clean and prepare in accordance with SSPC-SP-3. Prime by end of same work day and before forming of visible rust. 1. Remove oil, grease, and other foreign substances by lacquer thinner, conforming to

SSPC SPC-1. 2. Lightly scuff sand with 120 grit paper to break surface sheen without scratching or

scaring surface.

F. Hot-Dipped Galvanized Steel Treatment: Conform to ASTM D6386 for preparation of galvanized surfaces prior to application of primers and other coatings directly to galvanized surfaces. 1. Newly Galvanized Steel:

a. Within 48 hours of galvanizing, and before zinc oxide or zinc hydroxide formations on surface, clean surfaces of oil and grease.

b. Smooth high spots and rough edges by sanding or sweep blasting. c. Apply zinc-phosphate treatment or other acceptable adhesion promoter.

2. Partially weathered Galvanized Steel: a. Test for and remove chromatic conversion coatings that may have been applied at

factory. b. Clean surfaces of oil and grease. Smooth high spots and rough edges by sanding

or sweep blasting. c. Remove wet storage stain using a mild ammonia solution, rinse with water, and air

blow dry. d. Apply paint coating within 30 minutes before zinc oxides begin to reform or apply

zinc-phosphate treatment or other acceptable adhesion promoter. 3. Weathered Galvanized Steel:

a. After 1-1/2 to 2 years following formation of a hard zinc-carbonate surface, clean surfaces of oil, grease, and loose particles.

b. Smooth high spots and rough edges by sanding or sweep blasting. c. Scuff and brighten using 3M metal finish pad to remove zinc oxidation. d. Clean to remove surface contamination, conforming to SSPC-SP-1 Solvent

Cleaning and Manufacturer's priming instructions. 4. Verify preparation with manufacturer.

G. Zinc Coat Galvanized Ferrous Metal for Dryfall Coatings and Dryfall Paint at Interior Overhead Ceilings: 1. Rust-Inhibitive (not flash rust inhibitive), Low-Temperature Cure Dryfall Coatings: No

preparation required over dust-free and dry surfaces. 2. Dryfall Paint (Non Rust-Inhibitive): Conform to preparation surface preparation

methods including solvent cleaning, test for chromate passivation, and etching cleaner.

H. Wood Products Receiving Opaque Finishes: 1. Clean to remove dirt, bond breakers, and material that is not suitable for paint

adhesion to substrate. 2. Wipe off dust and minor grit prior to applying prime coat.




3. Fill fastener holes and fine cracks after primer has dried. 4. Sand smooth and level with surface, ready for finish coat. 5. Maintain surface condition for subsequent finish coats.

I. Interior Structural Wood Members (rough carpentry, dimensional lumber and plywood) at Office area: Shall not receive any finish. 1. Review cleaning procedures with Architect. 2. Use a light baking soda blast for cleaning. Do not etch or damage the wood. 3. Clean to remove dirt, bond breakers, and material. 4. Wipe off dust and minor grit. 5. Sand smooth and level with surface.

J. Wood Products Receiving Transparent Finishes: 1. Preparation: Sand, seal, and prepare surfaces to receive uniform coatings free of

blotches, inconsistent absorption, irregular sheen, and color variations. 2. Remove stains, discolorations, marks, and other surface inconsistencies through

sanding, bleaching, and other applicable methods. 3. Clean to remove dirt, bond breakers, and material not suitable for transparent finish

adhesion to substrate. 4. Wipe off dust and minor grit prior to applying prime coat. 5. Fill fastener holes and fine cracks with woody putty matching wood species. 6. Apply sanding sealer. 7. Sand smooth and level with surface, ready for finish coat. 8. Maintain surface condition for subsequent finish coats.

K. Priming Wood: 1. Prior to installation, prime all sides of wood, including concealed faces of panels,

moldings, siding, and other thin wood, plywood, and panel material subject to warping and bowing.

2. Prime cut ends of wood elements prior to installation. 3. Apply 2 coats of sealer, primer, or suitable finish system to balance finish on exposed

face.

L. Gypsum Board Surfaces: 1. Repair and remove minor irregularities, contaminations, dust, and dirt. 2. Where surface defects appear after prime coating, repair defects under work of

appropriate Section, and reprime over repaired areas. 3. Do not begin surface preparation on gypsum board materials that have been saturated

by water. Notify Owner and Architect.

M. Mechanical and Electrical Work: Remove dirt, grease, and oil from metal and insulating coverings.

3.6 PROTECTION

A. Take measures to protect surfaces not receiving work of this Section including protection from overspray, adjacent surfaces and down wind surfaces. 1. Provide drop cloths, shields, and protective equipment. 2. Repair or replace damaged surfaces caused by failure to provide suitable protection.




B. Remove or mask electrical outlets and switch plates, mechanical diffusers, escutcheons, registers, surface hardware, fittings, fastenings, and other items not receiving coating system.

C. Remove door hardware from doors and frames in preparation for painting.

D. Correct minor defects and clean substrate surfaces included under work of this Section.

E. Remove coatings that exhibit surface defects or unsuitable surface adhesion.

3.7 APPLICATION

A. Conform to manufacturer's instructions, MPI, and provisions of Contract Documents.

B. Conform to Premium Grade, including application of two finish coats over prepared and primed substrates.

C. Apply as many additional coats for complete coverage and for acceptable finished appearance, free of holidays and color irregularities.

D. Apply primer and each finish coat in slightly different hue as means to verify multiple coat coverage.

E. Conform to manufacturer’s instructions for wet film and dry film thickness of coatings. 1. Apply coatings at manufacturers’ specified application rates. Do not thin coatings. 2. Verify wet film thickness (WFT) by use of wet film gage during application. 3. Test dry film thickness (DFT) using Tooke or other accepted measuring device.

3.8 PATCHING

A. Repair surfaces damaged during construction activities. Touch-up and refinish as necessary for finished appearance prior to Substantial Completion and Owner occupancy.

B. Construction and trade damage shall be paid by the trade who did the damage.

3.9 REPLACEMENT OF HARDWARE AND MISCELLANEOUS ITEMS

A. Reinstall items previously removed for painting, including hardware, electrical plates.

3.10 FIELD QUALITY CONTROL

A. Independent Field Inspection and Testing: Conform to Quality Assurance provisions specified in this Section and provisions of Section 014324 for Painting Inspection Services.

3.11 ADJUSTING

A. Take measures as necessary and as instructed by Architect to repair, prepare, and recoat systems not conforming to Contract Document provisions.




3.12 CLEANING

A. As Work proceeds, promptly remove spilled, and splattered paint and coating products so as not to damage surfaces.

B. Maintain premises free from unnecessary accumulation of tools, equipment, surplus materials, and debris.

C. At conclusion of work, thoroughly clean paint and coatings from surfaces not designated to be painted. 1. Do not scratch or damage surfaces. 2. Verify chemical compatibility of cleaners to materials to be cleaned.

D. Leave premises neat, clean and free from debris and residue from work of this Section.

E. Do not dump paint, stains, chemicals and clean/wash painting equipment anywhere in the landscaping around the building, site, or property, including the adjoining property.

F. Control and dispose of unused painting and coating system products and waste as require by environmental laws.

3.13 EXTERIOR PAINTING SCHEDULE

A. Exterior Galvanized and Shop Primed Ferrous Metal: Include interior and exterior surfaces of doors and frames at exterior walls, handrails, and other galvanized metal surfaces. 1. Pre-Treatment, Preparation, and Shop Primers for Ferrous Metals and Aluminum: As

specified under work of Section 055000 and pre-primed metal under work of related Sections.

2. Pre-Treatment for Steel Doors and Frames: As specified Section 081113. 3. Field Applied Etching Cleaner (excludes factory primed doors and frames): Use in lieu

of SP-1 Solvent Cleaning, specified under preparation. a. Coronado Coroguard Super Etch Gray 317-200 b. Devoe Dev Prep 88 WB Heavy Duty Cleaner Concentrate c. Kelly-Moore Paint Co. Jasco Prep and Primer d. Sherwin-Williams, Sherwin-Williams, Clean & Etch

4. Primer: Do not apply alkyd primers or coatings directly to galvanized surfaces a. Benjamin Moore, Benjamin Moore Industrial, Acrylic Metal Primer, P04 b. Devoe Coatings, Devguard All Purpose Metal Primer, 4120 or 4160 or Devoe 4020

Devflex WB Acrylic DTM Primer Finish c. Kelly Moore, Acry Shield Acrylic Metal Primer, 1725 (<100 g/l VOC) d. Parker / Comex Group, UltraTech Universal Water-Based Metal Primer C309 e. Sherwin-Williams, Pro Industrial Pro-Cyl Universal Acrylic Primer (100 g/l VOC)

5. Two Coat, Acrylic Semi-Gloss Finish (Gloss Level 5): a. Benjamin Moore, DTM Acrylic Latex, P28 b. Coronado Corotech DTM Acrylic Semi-Gloss Enamel 182 Line c. Devoe, Devflex, High Performance Waterborne Acrylic, 4216-0100. or Devoe

Devflex 4206 QD WB Acrylic Semi-Gloss d. Kelly-Moore, Dura-Poxy+ Gloss Acrylic Enamel, 1680 (<100 g/l VOC) e. Parker, DTM Acylic Semi-Gloss 9225 f. Sherwin-Williams, Pro Industrial 0 VOC Acrylic, 113.03 (0 g/l VOC)




B. Exterior Ferrous Metal Subject to Moisture: Special Coating at exposed portions of overhead steel decking, sheet metal, hollow metal, and overhead and vertical structural steel members at Trash area. 1. Tnemec or Sherwin Williams:

a. Preparation: New preprimed, galvanized, and prefinished metals: Prepare in accordance with ASTM D6386.

b. Preparation: Uncoated, ungalvanized, and existing ferrous metals: power tool clean and prepare in accordance with SSPC-SP-3. Prime by end of same work day and before forming of visible rust.

c. Primer Tnemec: Touch-up shop prime, Series 394 Periprime, Aromatic Polyurethane, Mio-Zinc Filled Primer.

d. Primer S-W: Touch-up shop prime, Corothane I Galvapac 1k Zinc Primer B65G11 e. Field Finish Tnemec: 2 coats of Series 115 Uni-Bond DF, Self-Crosslink

hydrophobic Acrylic at 2 to 4 mils DFT per coat. f. Field Finish S-W: Sher-Cryl HP Acrylic Coating B66 Series g. Colors: Match PPG 541-2, Glistening Frost.

C. Exterior Glue-Lam Units - Satin Spar Marine Varnish: 1. Two Coat Application, Sand lightly between coats.

a. Benjamin Moore, Moore's, Sunbar Clear Spar Varnish, 441-00 b. Coronado Marine Spar Varnish 149 Line c. Kelly Moore, McCloskey, Man O’War, 7509 d. Parker Paint, McCloskey, Man O’War, 7509 e. Sherwin Williams, Minwax, Helmsman, Spar Varnish

D. Wood Siding – Penetrating Oil Based Finish: Low VOC formula, water repellant, UV protection. 1. Two Coat Application.

a. Messmer’s UV Plus for Hardwood Decks

E. Exterior Plastic - Including PVC and ABS Materials including downspouts: 1. Bonding Primer:

a. Benjamin Moore, Fresh Start, All-Purpose Acrylic latex Primer, 023 b. GliddenProfessional 3210 Gripper, 100% Acrylic Primer Sealer or Devoe Devran

210 Universal Epoxy Primer c. Kelly Moore, Kel Bond 287 (<100g/l VOC) d. Parker Paint CGI , General Paint, Bonding Primer, 51-050 e. Sherwin-Williams, DTM Bonding Primer B66-A50 (100 g/l VOC)

2. Two Coat, Acrylic Semi-Gloss Finish (Gloss Level 5): a. Benjamin Moore, DTM Acrylic Latex, P28 b. Coronado Corotech DTM Acrylic Semi-Gloss Enamel 182 Line c. Devoe, Devflex, High Performance Waterborne Acrylic, 4216-0100 d. Kelly-Moore, ACRY-SHIELD Exterior Semi-Gloss acrylic Finish, 1250 (<100 g/l

VOC) e. Parker, DTM Acylic Semi-Gloss 9225 f. Sherwin-Williams, Pro Industrial 0 VOC Acrylic, 113.03 03 (0 g/l VOC)

3.14 INTERIOR PAINTING SCHEDULE

A. Conform to manufacturer's instructions, and provisions of Contract Documents. Where in conflict, assume requirements that are more stringent and verify with Architect.




B. Interior Ferrous Metal - Paint Finish: 1. Shop Primer Coat: Refer to Section 055000 for metal shop fabrications. 2. Touch-Up / Field Primer: White or Gray color. Red primer not accepted.

a. Benjamin Moore, Acrylic Metal Primer, P04 b. Coronado Rust Scat Acrylic Metal Primer 36-11 c. Devflex DTM Flat Int/Ext WB Primer/Finish, 4020 d. Kelly-Moore, ACRYSHIELD Acrylic Metal Primer, 1725 (<100 g/l VOC) e. Parker / Comex Group, UltraTech Universal Water-Based Metal Primer, C309, (85

g/l VOC) f. Sherwin-Williams, Pro Industrial Pro-Cryl Universal Primer Off White B66W310

(<100 g/l VOC) 3. Two Coat, Acrylic Semi-Gloss Finish (Gloss Level 5):

a. Benjamin Moore, Latex, P28-08 b. Coronado Corotech Acrylic Semi-Gloss Enamel 182 Line c. Devoe, Hi Performance Waterborne Acrylic, 4216-0100 d. Kelly-Moore, DURA-POXY + Semi-Gloss Acrylic Enamel, 1685(<100 g/l VOC) e. Parker/General, Envirogard WB Acrylic Semi Gloss, 15-020 f. Sherwin-Williams, ProClassic Waterborne Semi-Gloss B31-850 Series (145 g/l

VOC)

C. Interior Non-Ferrous Metal - Paint Finish: 1. Shop Preparation and Shop Primer: Specified Section 055000. For factory coated

aluminum, refer to paint manufacturer instructions for bonding primer. 2. Touch-up / Field Primer:

a. Benjamin Moore, Acrylic Metal Primer P04 b. Coronado Rust Scat Acrylic Metal Primer 36-11 c. Devoe Deveflex, DTM Flat Waterborne Primer and Finish, 4020 d. Kelly-Moore, ACRYSHIELD Acrylic Metal Primer, 1725 (<100 g/l VOC) e. Parker / Comex Group, UltraTech Universal Water-Based Metal Primer, C309, (85

g/l VOC) f. Sherwin-Williams, DTM Bonding Primer B66-A50 (51 g/l VOC)

3. Two Coat Acrylic Semi-Gloss Finish (Gloss Level 5): a. Benjamin Moore, Moorcraft Super Spec Latex Semi-Gloss Enamel, 276 b. Coronado SuperKote 5000 Acrylic Semi-Gloss Enamel 32 Line c. GliddenProfessional, 1412 Ultra Hide 150 Interior Latex Semi-Gloss d. Kelly-Moore, PROFESSIONAL Interior Acrylic, Semi-Gloss Enamel, 1050 (<100 g/l

VOC) e. Parker, DTM Acrylic Semi-Gloss, 9225, (97 g/l VOC) f. Sherwin-Williams, ProMar 200 Semi-Gloss B31W200 (138 g/l VOC)

D. Interior Dry-Fall Coating at Interior Exposed-to-View Overhead Steel Surfaces (Including Steel Decking and Structural Steel Framing Members) included in Alternate No. 8: One coat application, self-priming, dry-fall, rust and corrosion resistant coating system. Apply additional coats as required to cover for uniform finish with no holidays. 1. Pre-Treatment and Primers: Not required. 2. Dryfall Coating:

a. Benjamin Moore Sweep Up Spray Acrylic 156 b. Coronado Super Kote 5000 Acrylic Dryfall 112-1 c. Devoe Unigrip 4382 Modified Epoxy Egg Shell Dry Fall, 4380 Primer Finish Flat

White or Black d. Sherwin-Williams, Waterborne Acrylic Dry Fall B42W2 Eggshell White (100 g/l VOC)




E. Interior Glue-Lam Units - Satin Spar Marine Varnish: 1. Two Coat Application, Sand lightly between coats.

a. Benjamin Moore, Moore's, Sunbar Clear Spar Varnish, 441-00 b. Coronado Marine Spar Varnish 149 Line c. Kelly Moore, McCloskey, Man O’War, 7509 d. Parker Paint, McCloskey, Man O’War, 7509 e. Sherwin Williams, Minwax, Helmsman, Spar Varnish

F. Interior Clear Transparent Finished Wood - Semi-Gloss: Three-Coat Finish. Sanding sealer and Stain as instructed by manufacturer to match Architect’s sample. 1. Satin (Gloss Level 4): At hardboard bases

a. Benjamin Moore Stays Clear, Satin, 423 b. GliddenProfessional Woodpride, Interior Waterborne Aquacrylic Satin Varnish,

1802 c. Kelly-Moore, KEL-THANE II, 2097 (<200 g/l VOC) d. Parker, Old Masters, Interior Water-Based Polyurethane, Satin, (<275 g/l VOC) e. (Sherwin-Williams), Minwax Polycrylic Water-Based Protective Finish Satin Clear

(275 g/l VOC) 2. Semi-Gloss (Gloss Level 5): Tinted color at maple veneer hardwood plywood and

solid sawn maple lumber refer to Section 064100. a. Benjamin Moore Stays Clear, Satin, 423 b. Coronado Aqua Plastic Urethane Acrylic Varnish 70 Line c. GliddenProfessional Wood Pride Aquacrylic WB Gloss varnish, 1808 d. Kelly-Moore, KEL-THANE II, 2094 (<200 g/l VOC) e. Parker, Old Masters, Interior Water-Based Polyurethane, Semi-Gloss, (<275 g/l

VOC) f. (Sherwin-Williams), Minwax Polycrylic Water-Based Protective Finish Semi-Gloss

Clear (275 g/l VOC)

G. Interior Gypsum Board and Primed Wood - Low Odor (Low VOC) Paint: 1. Primer:

a. Benjamin Moore, Moorcraft Super Spec Latex Enamel Undercoater & Primer Sealer, 253

b. Coronado Super Kote 5000 Latex Primer Sealer 40-11 c. Glidden Professional, 1090 PVA Standard Interior Latex Sealer d. Kelly-Moore, Premium Axry-Plex Int PVA Primer/Sealer Low Odor/Low VOC 971-

100 (<20 g/l VOC) or Premium Acry-Plex Zero VOC Int Wall Primer & Undercoat 973-10

e. Parker / Comex Group, UltraTech Low Odor / Zero VOC Primer, C153 f. Sherwin-Williams, ProGreen 200 Low VOC Interior Latex Primer B28W600 (43 g/l

VOC) 2. Flat (Gloss Level 1): At ceilings

a. Benjamin Moore, Super Spec Green Flat 780 b. Coronado Air Care Odorless Latex Flat 1225 Line c. Glidden Professional, Life Master 9100 No VOC Flat d. Kelly-Moore, Enviro-Coat Interior Acrylic Flat Wall Paint, 1500 (0 VOC) e. Parker / Comex Group, UltraTech Low Odor / Zero VOC Flat, C129 f. Sherwin-Williams, ProGreen 200 Low VOC Interior Latex Flat B30-650 Series (44

g/l VOC) 3. Eggshell (Gloss Level 3): At walls

a. Benjamin Moore Super Spec Green Eggshell 783 b. Coronado Air Care Odorless Eggshell Enamel 1230 Line




c. Glidden Professional Life Master 9300 No 0 VOC Eggshell d. Kelly-Moore, Enviro-Coat Interior Acrylic Eggshell Enamel 1510, (0 VOC) e. Parker / Comex Group, UltraTech Low Odor / Zero VOC Eggshell, C132 f. Sherwin-Williams, ProGreen 200 Low VOC Interior Latex Eg-Shel B20-600 Series

(40 g/l VOC)

H. Interior Gypsum Board - Utility Areas: Includes walls and ceilings of areas subject to moisture such as toilet rooms, custodian closets, sprinkler rooms, and other utility areas subject to moisture. 1. Acrylic Primer:


b. Coronado Super Kote 5000 Latex Primer Sealer, 40-11 c. Glidden Professional 1030 PVA Wall Primer/Sealer or High Hide Primer 1000 d. Kelly-Moore, ACRY-Plex Interior Latex Primer/Sealer, 971(<20 g/l VOC) e. Parker / Comex Group, UltraTech Primer Sealer, C152, (50 g/l VOC) f. Sherwin Williams, PrepRite, Interior Latex Primer, B28W200 (87 g/l VOC)

2. Two Coat Acrylic Semi-Gloss Finish (Gloss Level 5): Walls and ceilings. a. Benjamin Moore, Moorcraft Super Spec Latex Semi-Gloss Enamel, 276 b. Coronado Super Kote 5000 Acrylic Semi-Gloss Enamel 32 Line c. GliddenProfessional, 1416 Ultra Hide Interior Latex Semi-Gloss d. Kelly-Moore, PROFESSIONAL Interior Acrylic Semi-Gloss Enamel, 1050 (<100 g/l

VOC) e. Parker / Comex Group, UltraTech Interior Latex Semi-Gloss Enamel, C119 (124 g/l

VOC) f. Sherwin-Williams, ProMar 200, Zero VOC Interior Latex B20 Series

3.15 SPECIAL INTERIOR PAINT

A. Interior Gypsum Board - Utility Areas (Tile-Like Finish): Includes walls of areas subject to high moisture including Kitchen Production areas (Rooms 150A – 150G). 1. Acrylic Primer:


b. Coronado Super Kote 5000 Latex Primer Sealer, 40-11 c. GliddenProfessioanl 1030 PVA Wall Primer/Sealer or High Hide Primer 1000] d. Kelly-Moore, ACRY-PLEX Interior Latex Primer/Sealer, 971 (<20 g/l VOC) e. Parker / Comex Group, UltraTech Primer Sealer, C152, (50 g/l VOC) f. Parker/General, Breeze, Super Seal Latex, 51-087 g. Sherwin Williams, PrepRite 200, Interior Latex Primer, B28W200 (87 g/l VOC)

2. Two Coat, Waterborne Epoxy Finish: (Gloss Level 7) a. Benjamin Moore, Super Spec Acrylic Epoxy Coating, 256 b. Coronado Coropoxy Waterborne Acrylic Epoxy 138 line c. Devoe, Tru-Glaze WB, 4408 Gloss Devoe 4406 Semi-Gloss d. ICI Dulux, Devoe, Tru-Glaze WB, 4408 Gloss Devoe 4406 Semi-Gloss e. Kelly-Moore, Sierra Waterborn Epoxy S60 (0 VOC) f. Parker- Ameron, WB Epoxy Acrylic, 335 g. Sherwin Williams, Pro Industrial Hi-Build W/Based Catalyzed Epoxy, B71 Series

B. Interior Gypsum Board - Walls to Receive Wall Coverings and Visual Display Surfaces: One Coat: Waterborne Primer/Sealer, Vapor Barrier, perm rating less than 1.0. 1. Primer:




a. Benjamin Moore, Super Spec Vapor Barrier Primer, 260 b. GliddenProfessional 1060 Vapor Barrier Primer Sealer c. Kelly-Moore, Vapor-Shield Wallboard & Masonry Primer/Sealer, 95-500 (<10 g/l

VOC) d. Parker, Perm Gard, Latex Vapor Barrier, 1845, (83 g/l VOC) e. Sherwin-Williams, Moisture Vapor Barrier, Primer/Finish B72W1 (73 g/l VOC)

2. One Coat or more coats as recommended by manufacturer: a. Benjamin Moore Stays Clear, Satin, 423 b. GliddenProfessional Woodpride, Interior Waterborne Aquacrylic Satin Varnish,

1802 c. Kelly-Moore, KEL-THANE II, 2097 (<200 g/l VOC) d. Parker, Old Masters, Interior Water-Based Polyurethane, Satin, (<275 g/l VOC) e. Sherwin-Williams, Wood Classics, Waterborne Polyurethane, A68F90

3.16 EXPOSED MECHANICAL AND ELECTRICAL WORK IN FINISHED SPACES

A. Ferrous Metal Ducts, Exposed Piping, and Conduit (Except Stainless Steel): As specified this Section for ferrous metal - paint finish.

B. Exposed Galvanized Ducts, Piping, and Conduit: 1. Acrylic Primer: Gray color. Red primer not accepted.

a. Benjamin Moore, Acrylic Metal Primer P04 b. Coronado Insul-x Aqualock Primer c. GliddenProfessional 3210 Gripper stain Killer Primer-Sealer or Deveflex 4020 HP

DTM Flat Waterborne Primer and Finish, or Devoe 4030 Tru Glaze WB Epoxy Primer d. Kelly-Moore, ACRY SHIELD Acrylic Metal Primer, 1725 (<100 g/l VOC) e. Parker/General, Bonding Primer, 51-050 f. Sherman-Williams, DTM Primer/Finish, B66W1 (51g/l VOC)

2. Two Coat Acrylic Semi-Gloss Finish (Gloss Level 5): a. Benjamin Moore, Moorcraft Super Spec Latex Semi-Gloss Enamel, 276 b. Coronado Coropoxy Waterborne Acrylic Epoxy 138 line c. Kelly-Moore, PROFESSIONAL Interior Acrylic Semi-Gloss Enamel, 1050 (<100 g/l

VOC) d. Parker, DTM Acrylic Semi-Gloss, 9225, (97 g/l VOC) e. Sherwin Williams, Sher-Cryl HPA Semi-Gloss B66 Series (199 g/L VOC)

3. Two Coat Acrylic High-Gloss Finish (Gloss Level7): a. Benjamin Moore, Impervex Latex High Gloss Metal & Wood Enamel, 309 b. Coronado Super Kote 5000 Acrylic Gloss Enamel 414-01 c. Devoe 4428 Tru Glaze WB Epoxy Gloss, (< 50 g/l VOC) d. Kelly-Moore, Dura-Poxy+ Gloss Acrylic Enamel, 1680 (<100 g/l VOC) e. Parker General, Envirogard, 15 Line, (220 g/l VOC) f. Sherwin Williams, Sher-Cryl HPA Gloss B66 Series (199 g/L VOC)

4. Exposed Cloth Insulation Coverings for Pipes and Ductwork: 5. Undercoat: Drywall joint compound thinned with Latex Sealer to working consistency. 6. Acrylic Primer:


b. Coronado Super Kote 5000 Latex Primer Sealer 40-11 c. Glidden Professional 1000 Hi Hide Primer Sealer d. Kelly-Moore, Acry Plex 971 Interior Primer Sealer (<20 g/l VOC) e. Parker / Comex Group, UltraTech Primer Sealer, C152, (50 g/l VOC) f. Sherwin Williams, PrepRite Classic, B28W111 (41 g/l VOC)




7. Two Coat Acrylic Eggshell Finish (Gloss Level 3): a. Benjamin Moore, Moorcraft Super Spec Latex, Pearl Enamel, 277 b. Coronado Super Kote 5000 Interior Eggshell Enamel 30 Line c. Glidden Professional, 1412 Ultra Hide 150 Interior Latex Eggshell d. Kelly-Moore, PROFESSIONAL Interior Acrylic Eggshell Enamel, 1010 e. Parker Paint, Pro Satin, Interior Latex Satin Gloss, 5750, (127 g/l VOC) f. Sherwin Williams, ProMar 200 EgShel B20W200 (99 g/L VOC)

C. Inside of Ducts, Where Visible from Room: 1. Same treatment as specified for galvanized and ferrous metal surfaces. 2. Two Coat Acrylic Flat Finish: As specified this Section for each materials. Dull black

color.

D. Exposed Registers, Grilles, Exposed Conduit, Electric Cabinets, and Unfinished Portions of Cast-iron Fixtures Exposed to View: 1. Same treatments as specified for applicable materials. 2. Acrylic Finish Coat: As specified this Section for each materials. Match adjacent

surfaces. 3. Use bonding primer for factory prefinished items

END OF SECTION

FWPS CENTRAL KITCHEN SECTION 092216 FEDERAL WAY … · 6. ASTM C754 - Standard Specification for...

Documents

Transcript of FWPS CENTRAL KITCHEN SECTION 092216 FEDERAL WAY … · 6. ASTM C754 - Standard Specification for...