Fusion Pro - Stain Resistant Grout - Without Sealing
-
Upload
jancy-associates -
Category
Technology
-
view
321 -
download
3
description
Transcript of Fusion Pro - Stain Resistant Grout - Without Sealing
Information for the Design ProfessionalArchitect – Specifier – Interior Designer
Howard Jancy, CSI, CDTArchitectural Consultant | Custom Building Products
312-515-9215 :Cell | Email: [email protected]
What is Fusion Pro™ Single Component Grout™?
A patent-pending breakthrough in grout technology that delivers the best attributes of cement and epoxy grouts.
• Exceptional color consistency.• Superior stain resistance that exceeds
the performance of many epoxy grouts. No sealing is required.
• Handling and cleaning easier than epoxy grouts
• A durable, ready to use formula that is crack resistant and approved for interior and exterior applications.
Is it Cement? Epoxy? Urethane?
Fusion Pro™ is an advanced acrylic plus silicone resin.
Different than a Pre-mixed Grout
Fusion Pro™ Single Component Grout does not have any of the negative features associated with traditional premix
grouts:
• No soft grout joints• No short open time/stickiness• Much higher level of water resistance
We are trademarking the term “Single Component Grout” to highlight the superior performance of Fusion Pro™ over traditional premixed grouts.
Stain Resistance
Stain rate : 0 – 4 ( 0 – no visible stain 4 - intense)Source: Results based on internal testing
Stain resistance @ 4 hours dwell Fusion Pro™ Urethane Simple
Premix Epoxy Cement
water 0 0 0 0 1
coffee 0.5 1 1 2 2
red wine 0 0 0 2 3
soy sauce 0 0 0 0.5 3
ketchup 0 0 0 0 4
mustard 0.5 2 1 3 3
vegetable oil 0 0 0 0 4
Total 1 3 2 7.5 20
Microban’s patented formula works continuously to inhibit the growth of damaging microbes such as stain-causing bacteria, mold and mildew. Microban acts to reduce odors and deterioration of cured Fusion Pro™ grout.
Microban Antimicrobial Protection
Fusion Pro™ vs. Epoxy
Advantage of Fusion Pro™ Matches Fusion Pro™ Limitation of Fusion Pro™
Easy to use / workability Color Consistency Limited Chemical Resistance
No Epoxy Reaction Stain Resistance Not for Commercial Kitchens
No Mixing / Single Component Cleaning
Reusable
Price
Fusion Pro™ vs. Cement
Advantage of Fusion Pro™ Matches Fusion Pro™ Limitation of Fusion Pro™ Color Consistency Ease of use / workability Not Recommended for Submerged Areas
Stain Resistance Hardness Cost No Efflorescence No Mixing / Single ComponentReuseChemical Resistance Dustless
Fusion Pro™ vs. Urethane
Advantage of Fusion Pro™ Matches Fusion Pro™ Limitation of Fusion Pro™ Ease of use / workability Color ConsistencyStain Resistance No Efflorescence Price No Mixing / Single ComponentChemical Resistance ReuseCleaning Dustless
Unique Installation Attributes
• Work directly from the pail. No mixing required.• Unlike other grouts: Cleaning can begin immediately.• Unlike other grouts: To extend working time or recover drying
Fusion Pro™ grout, rewet surface with a moderately damp grout sponge.“When in doubt…wet it out!”
• Accepts light traffic in 24 hours.*• Accepts heavy foot traffic in three days.*
*Will vary with temperature, humidity and grout joint width. On-site mock up recommended.
Sealing After Tile & Grout Installation
• Fusion Pro™ grout’s unparalleled stain resistance means it does not need to be sealed
• If sealing of the tile after the installation of Fusion Pro™ is required, allow seven days for Fusion Pro™ to cure prior to the application of any sealer
• Sealers manufactured by Custom Building Products have been tested for compatibility and are the only sealers recommended
Cost Comparison
• ANSI 118.3 Epoxy Grouts - $1.10 to $1.35/sqft + a premium for installation, $1.00 -$2.00/sqft
• ANSI 118.6 Cement Grouts - $.08 to $.12/sqft
• ANSI 118.7 Hi Performance Cement Grouts - $.15 to $.25/sqft
• Fusion Pro - $.4o to $.45/sqft
Architectural Specification
• To include Fusion Pro in an Architectal Specification, the following statement is added to the grouting material section of the specification:
Chemical Resistant, Water-Cleanable Tile Setting and Grouting Epoxy; ANSI A118.3:
Custom Building Products Fusion Pro Single Component, High Performance Grout. Meeting the performance requirement of ANSI A118.3 and A118.7. No mixing required and is stain resistant.
Howard Jancy, CSI, CDTArchitectural Consultant | Custom Building Products
312-515-9215 :Cell | Email: [email protected]