Nuclear Fusion Reactor Designs Utilizing Spherical Electromagnetic
Fusion Neutrons from a Strong Spherical Shock Wave …Design Specific/General Fusion... · D-D...
Transcript of Fusion Neutrons from a Strong Spherical Shock Wave …Design Specific/General Fusion... · D-D...
D-D FUSION NEUTRONS FROM A STRONG SPHERICAL SHOCK WAVE FOCUSED ON A
DEUTERIUM BUBBLE IN WATER
Dr. Michel LabergeGeneral Fusion Inc.
SONOFUSION
� Sonofusion is making some noise� A bit short in energy, ~mJ in bubble� Concentration of energy in a collapsing cavity
in a liquid is interesting� 1/r velocity, pressure and temperature� Worth considering
Spherically focused shock wave
� More energy required than the small ultrasound transducer
� More powerful sound wave becomes shock wave
Advantages of shock wave
� Focusing shock is stable
Defocus, slow down Focus, speed up
Advantages of shock wave
� All pictures of shocks from our experiment or from other work are very smooth, no bumps or jets. Shocks look nice and stable.
� Shocks can have extreme material velocity� Super Nova explosion� Nuclear explosion� Shocks are cheaper to produce than laser or particle
beam� If atomic liquid (liquid metal), the liquid is not damaged
Stable cavity collapse?
� Pressure in shock accelerates the dense liquid pushing against the lower density target.
� RT stable?
Final crunch of cavity
� At the final crunch, the less dense target slows the denser liquid.
� RT unstable for very short time at max compression.
� No worse than laser ICF
Target
� Target could be inertial confined (ICF)� Target could be a pre-formed magnetized
plasma (MTF)� Simpler is a D-T bubble, but more complex
multi-layered targets could be designed for a higher yield, like laser targets
� A compact torus (spheromak, FRC) could be used for MTF
MF to MTF to ICF
Magneticfusion
linus Imploding liner
ICFFocused shock
n=1E14 P=1 Bar v=0 km/s t=1 s
n=1E17 P=1 kBar v=0.5 km/s t= 1 ms
n=1E20 P=1 Mbar v=5 km/s t=1 us
n=1E25 P=100 Gbar v=500 km/s t=10 ps
Heat losses due to instability
Extreme powerdensity
Shock generation
� Electric (electromagnetic, electrothermal)� Cost of pulse power technology is ~2$/J� Rep rate ~1Hz, power supply only is ~2$/W� Max cost for power plan with negligible fuel
cost is ~2$/W to be economical� Piston impact delivers energy in 10 us� Compressed air or steam accelerates pistons� Very low cost, 10 MJ of compressed air 100 k$
Focused shock driven fusion plant
Focused shock driven MTF
Spin the liquidto form a vortex And inject a compact Torus (FRC, spheromak)
Engineering advantages
� All neutrons and other radiation stopped in the liquid
� The liquid re-breeds tritium (lead-lithium liquid alloy for example)
� Low neutron load on reactor structure� Very low cost drivers, low tech reactor� If (big if) the physics works out, could rapidly
lead to economical power generation
Possible pitfalls
� Symmetry requirements are high, especially for ICF
� Shock losses� Shock losses are deadly for spherical pinch,
but losses in low compressibility liquid metal may be lower than in a compressible plasma
� EOS of materials is not very well known, will make hydro simulations questionable.
Hydrodynamic simulation
� A small hydro simulation with HYADES to estimate possible fusion yields of small scale demonstration experiments predicts 1E-5 to 1E7 neutrons depending on the water EOS table used.
� Definitively need more simulation both for ICF and MTF.
� Any hydro simulation scientists interested???
Experiment
� Develop a shock generator� Piston impact will require fancy servo control
system to have suitably small time jitter� Not enough resources now� Electric discharges are easier to time right� First try spark-array igniting explosive gas
mixture
Experiment
� Acoustic impedance mismatch between exploding gas and liquid is too high
� Spark-array itself makes a nice shock in air
Cylindrical set-up
Cylindrical machine power supply
Cylindrical shock in air
Cylindrical shock in air
Cylindrical shock in water
� Spark-array did not work in water. Only one array fired and took all the energy.
� Changed to exploding aluminum foils by passing high current in them
� Worked well
Cylindrical shock and plasma
Naked sphere
Sphere
Sphere open
Spark gap switch
Capacitor bank
Ultrasound water degassing
Spherical mill
Aluminum foil spirals
Blown foil
Plastic scintillator
Shielded plastic scintillator
Shielded liquid scintillator
Bubble tracked by two cameras
Sphere specification
� Diameter: 16 cm� Surface accuracy: 20 um� Capacitor: 32 X 1.9 uF=60.8 uF� Max voltage: 60 kV� Max energy: 100 kJ� Timing accuracy between 32 foils: <5 ns� Ringing time: 11 us
Sphere specification
� Energy transfer time: 90% of energy in 5 us� Max Power, current: 20 GW, 700 kA� Experiment so far ran at: 38 kV, 9 GW, 400 kA� Deuterium bubble diameter: 100 um<D<6 mm� Bubble pressure: 0.4 psi to 160 psi� Bubble centering: +/- 30 um� Bubble spherical to better than 7 um
Detectors
� 5 x 5 x 7.5 = 187 cm3 plastic scintillator� 1.8 MeV gamma Compton edge at 150 mV� D=12.5 cm, L=7.5 cm, 920 cm3 NE213 liquid
scintillator� 1.8 MeV gamma Compton edge at 840 mV� Liquid scintillator can do pulse shape
discrimination (PSD). Neutrons produce longer pulses than gamma rays
AmBe PSD with analogue NIM
AmBe and Y88 PSD from digital traces from oscilloscope
AmBe and Y88 scatter plot
0
2000
4000
6000
8000
10000
12000
0 0.2 0.4 0.6 0.8
Fraction of energy in the tail
Inte
gra
ted
pu
lse
inte
nsi
ty
AmBey88
Results, 5 out of 8 shots in Deuterium gave a signal
Deuterium results
Deuterium results
Deuterium results
Deuterium results
4 out 4 shots with hydrogen gave no signal
Hydrogen results
Hydrogen results
All signals on a plot
All counts
0
50
100
150
200
250
300
1 7 13 19 25 31 37 43 49
time (us)
Pu
lse
hei
gh
t (m
V)
Series3Series2Series1
PSD of fusion results
AmBe and Y88 scatter plot
0
2000
4000
6000
8000
10000
12000
0 0.2 0.4 0.6 0.8
Fraction of energy in the tail
Inte
gra
ted
pu
lse
inte
nsi
ty
AmBey88fusion 10.8 usfusion 17 us
Results
� Signal above background� Particularly 3 signals at 10.7 +/- 0.1 us is very
unlikely� One would expect a quick neutrons peak, what
are the later counts?� Water thermalizes some neutrons, they diffuse
for many us, they are absorbed by water and steel and emit delayed gamma rays
Monte Carlo Simulation
� The delayed gammas are predicted by a neutrons and gammas transport code (MCNP)
� It predicts more neutrons than gammas, we seem to see more gammas than neutrons
� All fast neutrons arrive simultaneously, average neutron count is small. So our neutron peak may be many neutrons at the same time
� From this code and assumption, our best shot gave a fusion yield of 5E4
Interpretation
� The signal at 10.7 us is many neutrons at the same time from D-D fusion
� The later signals are gammas from thermal neutron absorption
� 10.7 us correspond to an average shock speed of Mach 5.
Review of the data
� We sent out the data to be reviewed by experienced scientists
� They were not convinced� One proposed to try to measure shock arrival
time in center, it should be 10.7 us if interpretation of the signal is correct
Shock arrival time measurement
Coaxial cable withsmall aluminumfoil just above centerconductor. Shock closesthe contact.
Shock timing
Shock arrival time
� The shock seems to arrive at 52.8 us, that is within experimental error Mach 1
� Not compatible with fusion signal at 10.7 us� Possible problem with the shock damaging the
cable and switch before the shock arrives giving the wrong timing
� Possibly correct, therefore no fusion signal
Future plan
� Try to detect neutrons in present set-up� Hydro simulation (anybody interested??)� If promising, build a bigger experiment� Cost ~5 M$� Energy 10 MJ� Time to build 2-3 years
Next phase