08 H191 W02 D03 1-2 V1.2 - Sketching Isometric Pictorials and Ellipses 08
Fundamentals of Engineering Isometric Sketching and Coordinate Systems GSMST.
-
Upload
wyatt-bartlett -
Category
Documents
-
view
246 -
download
6
Transcript of Fundamentals of Engineering Isometric Sketching and Coordinate Systems GSMST.
Fundamentals of Engineering
Isometric Sketching and Coordinate Systems
GSMST
2
Objectives
Define 2D and 3D coordinate systemsDetermine coordinates of objects in: 2D views 3D views
Practice drawing isometric from orthographic
Pictorial Sketching:
Coordinate Systems Used to define the locations of points, lines,
and planes in 2 or 3 dimensions.
"Cartesian Coordinate system"
Y
X
4
A 2-D coordinate system locates the origin at the intersection of the X axis (horizontal axis or abscissa) and the Y axis (vertical axis or ordinate).
These are called View Coordinates.
Coordinate Space in 2-D
-5
-4
-3
-2
-1
0
1
2
3
4
5
-5 -4 -3 -2 -1 0 1 2 3 4 5
X-X
-Y
Y
5
-8
-6
-4
-2
0
2
4
6
8
-8 -6 -4 -2 0 2 4 6 8
Determine the Coordinates
point X Y
A
B
C
D
-3 6
-3 -2
6 -2
0 2
A
B C
D
6
In the 3-D coordinate system (world coordinate system) the axes are mutually perpendicular.
The origin (0,0,0) is usually taken at the intersection of these axes.
Coordinate Space in 3-DZ
X
Y
-Z
-X
-Y
(0,0,0)
3-D Coordinate Systems
Consist of three, mutually perpendicular axes used to define space
Positive or negative based on the axes
Right Hand Rule determines if a coordinate system is positive (right-handed) or negative (left- handed)
3-D Coordinate systems are generally positive (right-handed)
Coordinate Systems: Right Hand Rule
Place your fingers in the direction of the positive x-axis and rotate them in the direction of the y-axis. Your thumb will point in the direction of the positive z-axis.
Left or Right-Handed? The systems are right-handed (positive).
Z X
Y
Y Z X
These systems are left-handed (negative). Z X
Y
Y X Z
Orthographic Projection: Missing Views Constructing the third view helps visualization
skills. When constructing the third view, recall: Points project perpendicularly from one view to the
next. bject dimensions (height, width and
depth) are preserved from one view to the next.
17
Orthographic Projection: Missing Views Two Solutions
18
Pictorial Sketching Used to portray a 3-D object on a 2-D
sheet of paper.
3-D axes appear differently when shown on a 2-D surface.
Standard axes:
Isometric
Oblique
Oblique Sketching
Since one face of the object is undistorted, the most irregular face is usually shown in the plane of the paper.
Oblique Coordinate Axes
Oblique Coordinate Axes Note: Surface parallel to the plane of the paper (the XY plane) is shown in its true shape.
Oblique sketches are made perpendicular to an edge on the object
34
Oblique Sketching
Oblique sketch from edge DC:
3 2 Oblique Sketching 1
To draw oblique sketches: 1. Draw the first surface completely 2. Add lines showing the receding dimension (depth) 3. Repeat until the object is complete
Notice: All receding lines are parallel to one another
19
Task: Using engineering paper, draw both these coded sketches.
Oblique Practice
4 3
2 1
5 4 6 2
3 3 2 11
Isometric Coordinate Axes
Isometric sketches are made as if you’re looking down a diagonal a cube
Isometric Coordinate Axes Note: all isometric object surfaces will appear distorted.
Square surface appears as a rhombus
Isometric sketches are made as if you were looking down a diagonal of a cube
Isometric Coordinate Axes Isometric grid paper/dot paper is useful for constructing isometric drawings.
We'll use grid paper in class and dot here in the PowerPoint
Coded Plans
Pictorial sketches can be made from coded plans.
Coded plans define the shape of a block building.
"Arrow" shows the corner you are drawing from
Coded Plan Building
Coded Plans: Isometric Sketch From Corner C
Isometric Sketching 1 3
2 1
C Guidelines for constructing isometric drawings:
C Step 4 ... Step 1 & 2 Step 3
0.Draw edge "C“1.Sketch right or left surface. 2.Draw a surface that shares an edge with the surface just drawn. 3.Continue drawing one surface at a time until the object is complete.
Step 4 ...
26
Task: Using isometric paper, draw these coded sketches.
Isometric Practice
4 3
2 1
5 4 6 3
3 3 1 0
27
Task: Using the world coordinates convention for computers and CAD,determine the values of the coordinates for points in orthographic drawings and isometric drawings. Note the origin (0,0,0) can be set at an any point.
Orthographic and Isometrics Coordinates
X
Z
Y
28
B
B B
B
Y
X
Z
X
Z
Y
X Y ZA 0 0 0
A
A A
3 5 5C
CC
C
4 1 2
DDD
D
7 1 0
World Coordinates in Orthographic Projections
29
B
B B
B
Y
X
Z
X
Z
Y
X Y Z
A 0 0 0
A
A A
3 5 5C
CC
C
4 1 2
DDD
D
7 1 0
X
Z
YA
D
C
BWorld Coordinates in Isometric Projections
30
World Coordinates in the Isometric
X
Z
Y
A
What are the
Coordinates Of this point?X Y Z
3 2 5
Orthographic Projection:
Orthographic Views from Isometric Sketches
Make an orthographic sketch, by sketching top, front and right side views of the object shown below.
2 3 1 1
Orthographic Projection:
Isometric Sketches from Orthographic Views
•Sometimes you are asked to construct isometric sketches from orthographic views.
•Orthographic views develop visualization skills
•The box method is one way to do this.
•For some problems, the box method may not be very helpful.
Orthographic Projection:
Iso. Sketches from Ortho Views 1. Find the object's overall dimensions from
the orthographic views and sketch that size box on isometric dot paper.
W
Orthographic Projection:
Iso. Sketches from Ortho Views 2. Sketch the top, front, and right side
views in their appropriate locations on the box.
Orthographic Projection:
Iso. Sketches from Ortho Views 3. Add/remove lines until the view is complete.