ppt- laser induced ignition of gasoline direct injection engines
Fuel injection system in c.i engines
-
Upload
vagish-tripathi -
Category
Engineering
-
view
1.040 -
download
3
Transcript of Fuel injection system in c.i engines
![Page 1: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/1.jpg)
Shankersinh Vaghela Bapu Institute Of Technology
Department of Mechanical
Internal Combustion Engines (2161902)
Prepared ByRahul Someshvar 13ME119Utsav Thakor 13ME120Vagish Tripathi 13ME121
Fuel Supply System For C.I Engine
![Page 2: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/2.jpg)
2
Fuel injection system for diesel engine
![Page 3: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/3.jpg)
3
Air Injection System
Here, the fuel is injected by means of high pressure air at about 70 bar into the combustion
chamber.
It needs compressor to supply compressed air & the fuel pump to draw the desired fuel from
fuel tank both to be supplied to the injector.
AdvantagesI. Provides good atomization of fuel.
II. Heavy viscous fuel can be used .
Disadvantages
I. Air compressor needs extra maintenance.
II. System is bulky and expensive.
![Page 4: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/4.jpg)
4
Solid or Airless Injection System
Here, fuel is directly injected into the cylinder without the aid of compressed air.
The fuel does not vaporize at ordinary temperatures & also the fuel supplied needs to be
atomized & mix with air, it requires high injection pressure over 70 bar.
Types of solid Fuel Injection System
I. Mechanical Injection
II. Electronic Injection
Mechanical Injection is further classified as:
a) Common rail direct injection (CRDI) system
b) Individual pump system
c) Distributor system
![Page 5: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/5.jpg)
5
Common-Rail Direct Injection (CRDI) System
![Page 6: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/6.jpg)
6
Advantages
I. This system is simple & easy to maintenance.
II. It Can control fuel supply as per load & speed of engine.
III. It has only one pump needed for a multi-cylinder engine.
Disadvantages
I. System needs accurate design .
II. There is a chance of developing leakage at the valve seat.
III. Injection pressure used are in range of 200 – 300 bar pressure.
![Page 7: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/7.jpg)
7
Individual Pump System
![Page 8: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/8.jpg)
8
Distributor System
![Page 9: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/9.jpg)
9
Electronic Injection
It uses the electronic sensors for precise metering of fuel.
The sensors feed the data to an electronic control unit (ECU) which determines the amount of fuel to be injected depending upon the engine speed & throttle position.
Advantages
I. Reduces fuel consumption & gives better mileage.
II. Reduces exhaust emissions.
III. Improves engine power.
IV. Prevents overheating of engine during braking & idling conditions of the engine.
![Page 10: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/10.jpg)
10
Fuel Injection Pumps
Objectives
I. To deliver accurately metered quantity of fuel.
II. High pressures in the range of 100 bar to 300 bar needed depending upon the
compression ratio of engine to achieve required atomization of fuel.
III. Fuel must be injected and terminated at the correct timing.
Types of Injection Pumps
I. Jerk type injection pump ( Bosch fuel injection pump )
II. Distributor type injection pump
![Page 11: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/11.jpg)
11
Bosch Fuel Injection Pump
![Page 12: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/12.jpg)
12
![Page 13: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/13.jpg)
13
Distributor Type Fuel Pump
![Page 14: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/14.jpg)
14
Nozzles
Nozzle is the part of an injector through which the fuel is injected into the combustion chamber.
Design of nozzle should be such that the liquid fuel leaving the nozzle is atomized which helps in proper mixing of fuel & air.
Type of nozzle used in an injector depends on the type of combustion chamber used in an engine.
Various types of Nozzles:
I. The pintle nozzle
II. The single hole nozzle
III. The multi-hole nozzle
IV. The pintaux nozzle
![Page 15: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/15.jpg)
15
Pintle Nozzle
I. Have thin ends in the form of pin.
II. Shape of the pin can be varied.
III. Hollow cylindrical jet or a wide angle spray
can be obtained.
Specifications:
Advantages
I. It avoids dribbling of fuel in the combustion chamber
![Page 16: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/16.jpg)
16
Single hole nozzle
Specifications
I. A single hole is bored at bottom tip of nozzle.
II. Hole diameter is of 0.2 mm.
III. Spray cone angle obtained ranges from 5-20
degrees.
AdvantagesI. Suitable for open combustion
chamber
Disadvantages
I. Gives small spray cone angle.
II. Have a tendency to dribble.
![Page 17: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/17.jpg)
17
Multiple hole Nozzle
Specifications
I. Have multiple holes bored at the tip of the nozzle.
II. Number of holes vary from 4 to 8.
III. Diameter vary from 0.2 mm to 0.35 mm.
AdvantagesI. It ensures proper mixing of fuel in the
chamber.
Disadvantages
I. It requires high injection pressures in the range of 180 to 200 bar.
![Page 18: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/18.jpg)
18
Pintaux Nozzle
Specifications
I. Pintle type of nozzle with an auxiliary hole drilled in it.
II. Auxiliary hole injects fuel in a direction upstream the direction of air before the main
injection starts.
Advantages
I. It reduces the delay period due to better heat transfer
between fuel & air.
II. It results into better cold starting performance.
![Page 19: Fuel injection system in c.i engines](https://reader036.fdocuments.us/reader036/viewer/2022062503/589cf95d1a28abcc258b67c5/html5/thumbnails/19.jpg)
19
Thank You