Fs22 installation - fire coating in malaysia, fire stopping, fireproofing
1
Page 1 of 1 FS22 Firestop Pillows Installation Instructions FS22 Firestop Pillows provide up to 4 hours fire protection in floors and walls when sealing around metal pipes, cable trays, cable bunches and trunking. Installation in Walls (Method 1) 1) Push the first FS22 Firestop Pillows into the hole to be filled, so that the longest dimension (300mm long) spans across the wall. 2) For electrical trunking, remove the lid and install a pillow inside so it aligns with the depth of the wall. Replace the lid on the electrical trunking. 3) Pack the hole tightly with more FS22 Firestop Pillows until it is full. Installation in Walls (Method 2) 1) Make a basket using galvanized steel mesh (50 x 50 squares x 2.5mm wire diameter) to sit into the hole in the floor slab. There should be a minimum 50mm overlap onto the surrounding floor slab or wall (see diagram on technical data sheet). Mechanically fix to top of floor slab or wall. 2) Lay FS22 Firestop Pillows standing on end into the wire basket. Pack the pillows tightly into the basket around the penetrating services. 3) For electrical trunking, remove the lid and install a pillow inside so that it aligns with the depth of the floor. Replace the lid on the electrical trunking. 4) Lay a sheet of the galvanized steel mesh over the basket and tie together using steel wire. Heath & Safety Instructions General: FS22 Firestop Pillows are manufactured from intumescent graphite compound and inert exfoliating fillers contained in a glass cloth bag. Dust may be generated if the bag splits prolonged exposure constitutes a health hazard. Eye Contact: If pillows split, the product may cause irritation or inflammation. Goggles must be worn. Dust or fibre generated from handling or cutting, if inhaled over a prolonged period, constitutes a health hazard. Skin Contact: The product may cause irritation to sensitive skins. Protective overalls and gloves should be worn to minimize exposure. If irritation occurs then wash the affected area thoroughly with soap and water. Inhalation: Inhalation may cause irritation. Ensure adequate ventilation when cutting and wear a dust mask complying with BS2091 or BS6016 Other Information The information is current as of March 2013. Please contact Fire Security for updates. Fire Security AS | Skibåsen 20b -4636 Kristiansand Norway T: +47 95 47 80 00 ׀F: +47 38 02 15 31 ׀Web: www.fire-security.net ׀Email: [email protected]
-
Upload
fire-security -
Category
Documents
-
view
50 -
download
7
description
Terms & Conditions about Fire Protection Service. Fire Security Systems are providing Fire Protection Products, Fire Coating, Fire Stopping, Cable Coating and Fireproofing services in USA, Canada, Africa, Middle East, Saudi Arabia, UAE, Malaysia, Indonesia, Korea, Kenya, Uganda, Baku, Bahrain and Many More Countries
Transcript of Fs22 installation - fire coating in malaysia, fire stopping, fireproofing
Page 1 of 1
FS22 Firestop Pillows Installation Instructions FS22 Firestop Pillows provide up to 4 hours fire protection in floors and walls when sealing around metal pipes, cable trays, cable bunches and trunking. Installation in Walls (Method 1)
1) Push the first FS22 Firestop Pillows into the hole to be filled, so that the longest dimension (300mm long) spans across the wall.
2) For electrical trunking, remove the lid and install a pillow inside so it aligns with the depth of the wall. Replace the lid on the electrical trunking.
3) Pack the hole tightly with more FS22 Firestop Pillows until it is full. Installation in Walls (Method 2)
1) Make a basket using galvanized steel mesh (50 x 50 squares x 2.5mm wire diameter) to sit into the hole in the floor slab. There should be a minimum 50mm overlap onto the surrounding floor slab or wall (see diagram on technical data sheet). Mechanically fix to top of floor slab or wall.
2) Lay FS22 Firestop Pillows standing on end into the wire basket. Pack the pillows tightly into the basket around the
penetrating services.
3) For electrical trunking, remove the lid and install a pillow inside so that it aligns with the depth of the floor. Replace the lid on the electrical trunking.
4) Lay a sheet of the galvanized steel mesh over the basket and tie together using steel wire.
Heath & Safety Instructions General: FS22 Firestop Pillows are manufactured from intumescent graphite compound and inert exfoliating fillers
contained in a glass cloth bag. Dust may be generated if the bag splits prolonged exposure constitutes a health hazard.
Eye Contact: If pillows split, the product may cause irritation or inflammation. Goggles must be worn. Dust or fibre
generated from handling or cutting, if inhaled over a prolonged period, constitutes a health hazard. Skin Contact: The product may cause irritation to sensitive skins. Protective overalls and gloves should be worn to
minimize exposure. If irritation occurs then wash the affected area thoroughly with soap and water. Inhalation: Inhalation may cause irritation. Ensure adequate ventilation when cutting and wear a dust mask
complying with BS2091 or BS6016 Other Information The information is current as of March 2013. Please contact Fire Security for updates.
Fire Security AS | Skibåsen 20b -4636 Kristiansand Norway T: +47 95 47 80 00 ׀ F: +47 38 02 15 31 ׀ Web: www.fire-security.net ׀ Email: [email protected]
